This document provides instructions for installing an engine in a 416F2 backhoe loader. It outlines 17 steps to correctly position and secure the engine, including connecting various components like the torque converter, electrical harnesses, air conditioning compressor, and fuel and cooling systems. Proper installation of the engine is critical for safe and reliable operation of the backhoe loader.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
2. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416F2 BACKHOE LOADER LYA
Configuration: 416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
416F2, 420F2 IT, 420F2 ST, 422F2, 428F2, 430F2 IT, 430F2 ST, 432F2, 434F2 and
444F2 Backhoe Loaders Engine Supplement
Media Number -UENR6152-01 Publication Date -01/06/2015 Date Updated -06/06/2018
i06199414
Engine - Install
SMCS - 1000-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7505 Hydraulic Jack 1
B 6V-3145 Load Leveling Beam 1
Illustration 1 g03849495
1. Attach Tooling (B) and a suitable lifting device to engine (30). The weight of engine (30) is
approximately 544kg (1200 lb). Use Tooling (B) and the suitable lifting device to position
engine (30) into the machine.
1/8
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g03849484
Illustration 3 g03849257
2. Align bell housing (28) to the engine and install bolts (29).
3. Rotate the engine and install bolts (26) in order to connect flywheel (27) to the torque
converter.
2/8
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g03849498
4. Install engine mounting bolts (31). Repeat on opposite side.
Illustration 5 g03849253
5. Install access panel (25).
Illustration 6 g02999824
6. Remove Tooling (A) from the transmission.
Illustration 7 g03849251
3/8
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 8 g03849240
7. Connect ground strap (24). Connect harness assemblies (21) to the electric starting motor.
Connect clip (22) to bracket (23).
Illustration 9 g03849221
8. Connect harness assemblies (20) to the alternator.
Illustration 10 g03849219
9. Position air conditioner compressor (19) on the engine and install bolts (18).
4/8
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 11 g03849206
10. Install fan and hub assembly (17). Install nuts (16).
Illustration 12 g03849203
11. Install fan shroud (15). Install fan guard (14). Install hose (13).
Illustration 13 g03849201
5/8
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 14 g03849199
12. Install tube (12). Install hoses (10) and (11).
13. Install tube (9). Install coolant tank (8).
Illustration 15 g03797235
14. Install fuel filter assembly (7).
Illustration 16 g03797205
15. Install plate assembly (5). Install bolts (4).
Note: Do not remove bolts (6).
6/8
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 17 g03797188
16. Position floor mat (3). Position plate (2) and install the bolts . Repeat on the opposite side of
the cab.
Illustration 18 g03797183
17. Turn battery disconnect switch (1) to the ON position.
18. Fill the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant
(ELC) - Change" for the correct filling procedure.
19. Fill the engine oil . Refer to Operation and Maintenance Manual, "Engine Oil and Filter -
Change" for the correct filling procedure.
End By:
a. Install air cleaner.
b. Install muffler.
c. Install hood assembly.
d. Install side panels.
Sun Dec 8 23:07:53 UTC+0800 2019
7/8
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416F2 BACKHOE LOADER LYA
Configuration: 416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02289796
Fuel Priming Pump and Fuel Filter Base - Remove and
Install
SMCS - 1258-010; 1260-010; 1261-010-SE; 1262-010
Removal Procedure
Table 1
Required Tools(1)
Tool Part Number Part Description Qty
ZZ
9U-7069 Cap 3
9U-7067 Cap 3
(1)
SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE
REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE
EXPERIENCED SERVICEMAN.
Start By:
a. Remove the assembly of the filter case and the fuel filter element. Refer to this Disassembly
and Assembly Manual, "Fuel Filter Base - Remove and Install".
Note: Put identification marks on all fuel hose assemblies and on all tube assemblies for
installation purposes. After being disconnected, plug all fuel hose assemblies and plug all tube
assemblies. This helps prevent fluid loss, and this helps to keep contaminants from entering the
system.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00952432
Typical example
1. Disconnect the tube assembly (5). Disconnect the tube assembly (6). Install dust covers onto
the connectors for the fuel priming pump.
2. Disconnect the fuel return line from the connector (3). Install a dust cover to the connector
(3).
3. Disconnect the harness assembly from the connector (2).
4. Support the fuel priming pump. Remove the three setscrews (1) and discard the rubber
washers. Remove the fuel priming pump (4).
2/3
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00952432
Typical example
1. Clean the external surfaces of the fuel priming pump (4). Position the fuel priming pump (4)
and install the setscrews (1) and new rubber washers.
2. Remove the dust covers from the fuel priming pump. Remove the plugs from the tube
assemblies. Connect the tube assembly (5). Connect the tube assembly (6).
3. Connect the fuel return line to the connector (3).
4. Connect the harness assembly to the connector (2).
5. Remove the air from the fuel system. Refer to the Operations and Maintenance Manual,
"Fuel System - Prime".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 8 23:09:12 UTC+0800 2019
3/3
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416F2 BACKHOE LOADER LYA
Configuration: 416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i01924034
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
ZZ
9U-7067 Cap 4
9U-7069 Cap 4
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS
SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01001306
1. Remove bolts (1). Remove cover (2) from the cylinder head.
2/4
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01001381
2. Disconnect fuel injection lines (3) at fuel injection nozzles (4).
3. Disconnect fuel injection lines (3) at fuel injection pump (5).
4. Remove the fuel injection lines.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01001381
1. Connect fuel injection lines (3) at fuel injection nozzles (4). Tighten the nut to 30 N·m
(22 lb ft).
2. Connect the fuel injection lines at fuel injection pump (5). Tighten the nut to 30 N·m
(22 lb ft).
3. Remove the air from the fuel system. Refer to Operations and Maintenance Manual, "Fuel
System - Prime".
3/4
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 4 g01001306
4. Position cover (2) on the cylinder head. Install bolts (1). Tighten the bolts to a torque of
9 N·m (80 lb in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 8 23:10:09 UTC+0800 2019
4/4
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416F2 BACKHOE LOADER LYA
Configuration: 416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i01878115
Fuel Injection Nozzles - Remove
SMCS - 1254-011
Removal Procedure
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g00975056
1. Remove hose (2) from fuel injection nozzle (1).
2. Remove bolt (3). Remove clamp (4) from the fuel injection nozzle.
3. Remove the fuel injection nozzle from the cylinder head. Remove O-ring seal (5) from the
fuel injection nozzle.
4. Remove seat washer (6) from the cylinder head.
Note: If the original seat washer is not removed, the projection of the fuel injection nozzle
will be incorrect when a new seat washer is installed.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 8 23:11:05 UTC+0800 2019
2/2
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416F2 BACKHOE LOADER LYA
Configuration: 416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i01878202
Fuel Injection Nozzles - Install
SMCS - 1254-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00975210
1/2
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 1. Lubricate seat washer (6) with clean engine oil. Install the seat washer in the cylinder head.
Note: If the original seat washer is reused, the projection of the fuel injection nozzle will be
incorrect.
2. Install O-ring seal (5) on fuel injection nozzle (1). Install the fuel injection nozzle in the
cylinder head.
Note: Alignment Pin (X) must be located opposite clamp (4).
3. Position clamp (4) on the fuel injection nozzle. Install bolt (3). Tighten the bolt to a torque
of 27 N·m (20 lb ft).
4. Install hose (2) to the fuel injection nozzle.
End By:
a. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Dec 8 23:12:02 UTC+0800 2019
2/2
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
21. Shutdown SIS
Previous Screen
Product: BACKHOE LOADER
Model: 416F2 BACKHOE LOADER LYA
Configuration: 416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
3054C Engines for Caterpillar Built Machines
Media Number -SENR5069-18 Publication Date -01/05/2015 Date Updated -19/09/2018
i02075261
Fuel Injection Pump - Remove - Delphi DP210
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Name Qty
A 230-6284 Timing Pin (Camshaft) 1
B 230-6283 Timing Pin (Crankshaft) 1
B 230-6283 Timing Pin ( Crankshaft) 1
C 9U-6198 Crankshaft Turning Tool 1
D 1P-2320 Combination Puller 1
ZZ
9U-7067 Cap 2
9U-7069 Cap 2
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
b. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
c. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install".
d. Remove the air compressor, if equipped. Refer to Disassembly and Assembly, "Air
Compressor - Remove and Install".
1/4
416F2 Center Pivot Backhoe Loader LYA00001-UP (MACHINE) POWERED BY C4...
2019/12/8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...