This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts.
This document provides instructions for assembling a torque converter for a 730 Articulated Truck. It lists 43 steps to assemble the various components of the torque converter in the correct order. Safety precautions are provided at the beginning regarding lifting heavy components and containing fluids. Diagrams illustrate each step. The summary ends by stating to connect the assembled torque converter housing to the planetary transmission.
Caterpillar cat 963 b track loader (prefix 9bl) service repair manual (9bl000...ujdjfjjskekmm
The document provides instructions for disassembling and assembling the air suspension system on a Caterpillar 963B track loader seat. It describes 22 steps to disassemble parts like the air spring, indicator, adjustment knob, and compressor. It then describes 19 steps to reassemble these parts in reverse order. Diagrams are provided to illustrate each step. Safety notices advise releasing air pressure before disassembly and wearing protective equipment when working with springs.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 345 c l hydraulic excavator (prefix pjw) service repair manua...hhfjksekmm
The document provides assembly instructions for a 345C excavator final drive system in 3 steps:
1. Adjust the bearing preload of the final drive by measuring dimensions and determining the correct shim thickness.
2. Assemble the carrier assemblies, which include installing planetary gears, bearings, shafts, and pins into housings.
3. Install the assembled carrier assemblies into the sprocket and ring gears in the correct order.
Caterpillar cat 319 d l excavator (prefix zca) service repair manual (zca0000...fjkskedmme
This document provides assembly instructions for a final drive on an excavator model 319D L. It involves 37 steps including installing bearings, seals, gears, and other components into housings and covers. Precise measurements and torque specifications are required. Cleanliness is important throughout the process. The completed final drive and sprocket assembly weighs approximately 310 kg.
Caterpillar cat 319 d l excavator (prefix kfm) service repair manual (kfm0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component. Some key steps in the disassembly include removing the cover, carrier assembly, ring gears, and separating internal planetary gears. Assembly involves installing bearings in the main housing, determining the correct shim thickness, installing seals, and reassembling internal components along with aligning the main housing to the motor housing. The instructions are detailed with illustrations and require specialized tools.
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Caterpillar cat 345 d l excavator (prefix jkn) service repair manual (jkn0000...hhfjksekmm
The document provides instructions for assembling a travel motor. It describes 33 steps to assemble parts like pistons, seals, plates, springs and valves. Measurements are checked with tools at several steps to ensure correct assembly. Cleaning parts and preventing contamination of hydraulic systems is emphasized.
This document provides instructions for assembling a torque converter for a 730 Articulated Truck. It lists 43 steps to assemble the various components of the torque converter in the correct order. Safety precautions are provided at the beginning regarding lifting heavy components and containing fluids. Diagrams illustrate each step. The summary ends by stating to connect the assembled torque converter housing to the planetary transmission.
Caterpillar cat 963 b track loader (prefix 9bl) service repair manual (9bl000...ujdjfjjskekmm
The document provides instructions for disassembling and assembling the air suspension system on a Caterpillar 963B track loader seat. It describes 22 steps to disassemble parts like the air spring, indicator, adjustment knob, and compressor. It then describes 19 steps to reassemble these parts in reverse order. Diagrams are provided to illustrate each step. Safety notices advise releasing air pressure before disassembly and wearing protective equipment when working with springs.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 345 c l hydraulic excavator (prefix pjw) service repair manua...hhfjksekmm
The document provides assembly instructions for a 345C excavator final drive system in 3 steps:
1. Adjust the bearing preload of the final drive by measuring dimensions and determining the correct shim thickness.
2. Assemble the carrier assemblies, which include installing planetary gears, bearings, shafts, and pins into housings.
3. Install the assembled carrier assemblies into the sprocket and ring gears in the correct order.
Caterpillar cat 319 d l excavator (prefix zca) service repair manual (zca0000...fjkskedmme
This document provides assembly instructions for a final drive on an excavator model 319D L. It involves 37 steps including installing bearings, seals, gears, and other components into housings and covers. Precise measurements and torque specifications are required. Cleanliness is important throughout the process. The completed final drive and sprocket assembly weighs approximately 310 kg.
Caterpillar cat 319 d l excavator (prefix kfm) service repair manual (kfm0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component. Some key steps in the disassembly include removing the cover, carrier assembly, ring gears, and separating internal planetary gears. Assembly involves installing bearings in the main housing, determining the correct shim thickness, installing seals, and reassembling internal components along with aligning the main housing to the motor housing. The instructions are detailed with illustrations and require specialized tools.
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Caterpillar cat 345 d l excavator (prefix jkn) service repair manual (jkn0000...hhfjksekmm
The document provides instructions for assembling a travel motor. It describes 33 steps to assemble parts like pistons, seals, plates, springs and valves. Measurements are checked with tools at several steps to ensure correct assembly. Cleaning parts and preventing contamination of hydraulic systems is emphasized.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 140 m 3 awd motor grader (prefix n9j) service repair manual (...ufjjsejfkskemme
This document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal process involves:
1. Removing the rear chassis support to access the pump.
2. Disconnecting hydraulic hoses and electrical harnesses from the pump.
3. Using lifting equipment to remove the 52 kg pump from the grader.
Reinstallation is the reverse of removal, including reconnecting hoses and harnesses and securing the pump with bolts. Proper cleaning and replacement of O-rings is emphasized to prevent contamination.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 349 f lxe excavator (prefix rax) service repair manual (rax00...fjsjjekdkme
The document provides instructions for disassembling and assembling the final drive of a 349F LXE excavator. The disassembly procedure involves removing 33 parts from the final drive including the ring gear, carrier assembly, planetary gears, and seals. The assembly procedure instructs installing 52 parts in the reverse order and specifies torque specifications and lubricants to apply during assembly. Tools required include lifting devices, punches, and seal installation tools.
Caterpillar cat 730 c articulated truck (prefix tff) service repair manual (t...ufjjsekkemmd
The document provides instructions for disassembling and assembling the torque converter of a 730C articulated truck. It lists 18 steps for disassembly, which include removing housing assemblies, bearings, plates, discs, seals and other internal components. It then lists 15 steps for assembly, which describe installing components in reverse order and include details on tooling used and proper torque specifications. The instructions note to keep parts clean from contaminants to prevent wear and shortened life.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fjjsjeskkekem
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f8uejkdkdmm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fuusejkddmmd3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujsekmd9idd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...shibi1322
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...fucheng89
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdksmmdmdd
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdkskmmdd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...8foskkdjdkdm3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...jiazhi27185
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujkse9didkke3
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...didkkskdmmd
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection from contamination during installation is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...km7seyrduhdw
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...yin9niaojiao
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 140 m 3 awd motor grader (prefix n9j) service repair manual (...ufjjsejfkskemme
This document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal process involves:
1. Removing the rear chassis support to access the pump.
2. Disconnecting hydraulic hoses and electrical harnesses from the pump.
3. Using lifting equipment to remove the 52 kg pump from the grader.
Reinstallation is the reverse of removal, including reconnecting hoses and harnesses and securing the pump with bolts. Proper cleaning and replacement of O-rings is emphasized to prevent contamination.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 349 f lxe excavator (prefix rax) service repair manual (rax00...fjsjjekdkme
The document provides instructions for disassembling and assembling the final drive of a 349F LXE excavator. The disassembly procedure involves removing 33 parts from the final drive including the ring gear, carrier assembly, planetary gears, and seals. The assembly procedure instructs installing 52 parts in the reverse order and specifies torque specifications and lubricants to apply during assembly. Tools required include lifting devices, punches, and seal installation tools.
Caterpillar cat 730 c articulated truck (prefix tff) service repair manual (t...ufjjsekkemmd
The document provides instructions for disassembling and assembling the torque converter of a 730C articulated truck. It lists 18 steps for disassembly, which include removing housing assemblies, bearings, plates, discs, seals and other internal components. It then lists 15 steps for assembly, which describe installing components in reverse order and include details on tooling used and proper torque specifications. The instructions note to keep parts clean from contaminants to prevent wear and shortened life.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fjjsjeskkekem
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f8uejkdkdmm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fuusejkddmmd3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujsekmd9idd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...shibi1322
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...fucheng89
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdksmmdmdd
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdkskmmdd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...8foskkdjdkdm3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...jiazhi27185
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujkse9didkke3
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...didkkskdmmd
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection from contamination during installation is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...km7seyrduhdw
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...yin9niaojiao
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...orrf0370383
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...fjskekxcddmmme
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...cdsaas
The document provides instructions for assembling a travel motor. It describes 33 steps for installing various components like seals, pistons, plates, and bearings. Measurements are taken throughout to ensure proper assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system. The travel motor must be filled with the correct oil type before operation to prevent damage.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...hhfjksekmm
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection from contamination during installation is emphasized.
Caterpillar cat 349 d l excavator (prefix gkf) service repair manual (gkf0000...fjjseksxckmdme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions to contain fluids. The procedure describes attaching a lifting device to the travel motor and removing bolts and hose assemblies to detach the travel motor from the excavator.
Similar to Caterpillar cat 349 e l excavator (prefix mpz) service repair manual (mpz00001 and up) (19)
Caterpillar cat m315 c wheeled excavator (prefix h2b) service repair manual (...cdsaas
The document provides instructions for disassembling the piston pump (swing) of an M315C wheeled excavator. It describes removing 22 individual parts from the pump housing including the servo valve, charge pump, gears, head, port plate, relief valves, spool, and adjustment screw. Cleanliness is important when disassembling to prevent dirt from entering the internal mechanisms. Personal injury precautions are also noted regarding hydraulic pressure and spring force.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...cdsaas
This document provides instructions for disassembling and assembling the main hydraulic pump of a M315C wheeled excavator. It lists 42 steps to disassemble the pump by removing components like valves, springs, seals, pistons, and bearings. It then lists the assembly steps in reverse order, noting to clean parts and apply new thread lock before reinstalling components. Precautions are provided to mark parts for orientation and contain fluids during maintenance.
Caterpillar cat 330 d2 l excavator (prefix xdr) service repair manual (xdr000...cdsaas
The document provides instructions for installing and removing an engine oil pump, water pump, and water temperature regulator on a Caterpillar 330D2 excavator. The oil pump installation involves cleaning components, installing various parts in sequence using specific tools and torques. The water pump removal requires draining coolant and removing hoses and bolts. Its installation aligns parts using guide studs and torques bolts in a given order. Removing the temperature regulator involves draining coolant and disconnecting hoses.
Caterpillar cat 330 d2 l excavator (prefix hsp) service repair manual (hsp000...cdsaas
The document provides instructions for disassembling a 330D2 excavator travel motor. It is a 27 step process that includes removing the head, brake piston, barrel assembly, cam plate, shaft assembly, and other internal components. Special tools are required and components must be marked for proper reassembly in the correct positions. Safety precautions are outlined to contain fluids and handle components carefully.
Caterpillar cat 330 d2 l excavator (prefix her) service repair manual (her000...cdsaas
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves 37 steps to remove all components of the final drive. Key steps include removing the final drive cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly process has 35 steps and involves installing components in reverse order while applying anti-seize compound and ensuring proper bearing preload using shims.
Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex000...cdsaas
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps including removing the final drive cover, carrier assembly, planetary gears, ring gears, and other components. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components of significant weight during disassembly. Cleanliness is emphasized to prevent dirt from entering internal mechanisms.
Caterpillar cat 330 d2 l excavator (prefix ex7) service repair manual (ex7000...cdsaas
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly, removing components like the head, port plate, bearings, brake piston, plates, and seals. It then lists 16 steps for assembly, replacing components in reverse order and noting specifics like lubrication, alignment marks, and press fittings. Precise installation of keys and cam plates is emphasized to prevent damage.
Caterpillar cat 330 d2 l excavator (prefix ebp) service repair manual (ebp000...cdsaas
The document provides instructions for disassembling an excavator travel motor. It begins by having the technician remove the travel motor from the excavator. The disassembly procedure then consists of 27 steps to dismantle the various components of the travel motor, including removing the head, brake piston, barrel assembly, cam plate, and other internal parts. Precautions are provided to properly contain fluids and mark components for reassembly. Required tools are also listed.
Caterpillar cat 330 d2 l excavator (prefix dtg) service repair manual (dtg000...cdsaas
The document provides instructions for disassembling a 330D2 excavator travel motor. It lists 27 steps to completely disassemble the travel motor, removing components like the motor head, brake piston, barrel assembly, cam plate, and shaft assembly. Tools required for the disassembly include an adapter, bolts, washers, eyebolt, retaining ring pliers, bearing puller, and shop air. Safety precautions are noted, such as containing fluids and avoiding damage to component surfaces.
The document provides instructions for installing and removing an engine oil pump, water pump, and water temperature regulator on a Caterpillar 330D2 excavator. The oil pump installation involves cleaning components, installing various parts in sequence using specific tools and torques. The water pump removal requires draining coolant and removing hoses and bolts. Its installation aligns parts using guide studs and torques bolts in a given order. Removing the temperature regulator involves draining coolant and disconnecting hoses.
The document provides instructions for disassembling a 330D2 excavator travel motor. The 27 step procedure includes removing the head, brake piston, barrel assembly, cam plate, shaft assembly, seals and other components. Special tools are required and technicians are advised to take care to not damage components and contain fluids.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves 37 steps to remove all components of the final drive. Key steps include removing the final drive cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly process has 35 steps and involves installing components in reverse order while applying anti-seize compound and ensuring proper bearing preload using shims.
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps including removing the final drive cover, carrier assembly, planetary gears, ring gears, and other components. Various specialized tools are required to disassemble parts and subassemblies. Cleanliness is important to prevent dirt from entering during disassembly.
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly, removing components like the head, port plate, bearings, brake piston, plates, and seals. It then lists 16 steps for assembly, replacing components in reverse order and noting specifics like lubrication, alignment marks, and press fittings. Precise installation of keys and cam plates is emphasized to prevent damage.
The document provides instructions for disassembling an excavator travel motor. It begins by having the technician remove the travel motor from the excavator. The disassembly procedure then consists of 27 steps to dismantle the various components of the travel motor, including removing the head, brake piston, barrel assembly, cam plate, and other internal parts. Precautions are provided to properly contain fluids and mark components for reassembly. Required tools are also listed.
The document provides instructions for disassembling a 330D2 excavator travel motor. It lists 27 steps to completely disassemble the travel motor, removing components like the motor head, brake piston, barrel assembly, cam plate, and shaft assembly. Tools required for the disassembly include an adapter, bolts, washers, eyebolt, retaining ring pliers, bearing puller, and shop air. Safety precautions are noted, such as containing fluids and avoiding damage to component surfaces.
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...cdsaas
This document provides instructions for removing and installing rear gear group components on a 330D L excavator powered by a C9 engine. The removal process involves using tools to remove retaining bolts and gears. Bearings are removed from adapters using tools as well. Clearances must be checked when installing new bearings. The installation process specifies torques for bolts and using loctite on reused bolts. Dimensions must be matched for bearing installation.
Caterpillar cat 330 d l excavator (prefix thj) service repair manual (thj0000...cdsaas
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like brackets, presses, and hammers/punches. Cleanliness is important to prevent dirt entry during disassembly.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...cdsaas
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Cleanliness is important to prevent contamination. The installation procedure specifies matching angles and distances when pressing bearings in place and lubricating bolts during reinstallation.
The flywheel removal involves using guide studs and lifting equipment due to the flywheel's weight. Removal of the ring gear may require a hammer and punch. Installation specifies heating the ring gear for pressing, applying thread
Caterpillar cat 330 d l excavator (prefix nbd) service repair manual (nbd0000...cdsaas
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, shafts, seals, and housing components using various tools while noting weights of parts removed. Detailed illustrations are provided for each step. Cleanliness is important to prevent dirt entry during disassembly.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i06192451
Fan Drive - Assemble - Hydraulic Fan Drive
SMCS - 1359-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1861 Retaining Ring Pliers 1
B 9U-7480 Compressing Tube 1
C 1P-1859 Retaining Ring Pliers 1
D 1P-1863 Retaining Ring Pliers 1
E - Loctite Flexible Anaerobic Gasket Flange 1
F - Loctite 648 1
G 359-4915 Driver 1
H 359-4916 Driver 1
Note: Caution is required while handling the lip seals. The lip seals can be damaged if objects or
cleaning fluids contact the sealing surface.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts except the lip
seals with cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to
dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If
any parts are worn or damaged, use new parts for replacement.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
1/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01333314
1. Use a suitable press to install bearing (29) into case (9) . Use Tooling (A) in order to install
retaining ring (28) .
Illustration 2 g01333310
Note: Caution is required while handling the lip seals. The lip seals can be damaged if
objects or cleaning fluids contact the sealing surface.
2. Apply Tooling (E) to the outside diameter of lip seal (27) . Carefully install lip seal (27) into
case (9) .
2/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g02092525
3. Install seal (25) onto shaft assembly (24) .
4. Apply Tooling (F) to the full diameter of the shoulder on shaft assembly (24) . Position new
sleeve (30) on shaft assembly (24) . The external chamfer on sleeve (30) will be on top. Use
Tooling (G) and a suitable press in order to install sleeve (30) . Remove excess Tooling (F) .
Illustration 4 g01333308
Illustration 5 g01286111
3/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 5. Position tube assembly (26) into case (9) .
6. Position case (9) and tube assembly (26) onto shaft assembly (24) .
7. Use a suitable press and a suitable driver to press shaft assembly (24) through the bearing
and through tube assembly (26) .
Illustration 6 g01333303
8. Use Tooling (D) in order to install retaining ring (23) . Install seal rings (22) onto shaft
assembly (24) .
Illustration 7 g01333301
9. Install spring (21) on clutch housing assembly (11) .
4/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g01333300
10. Install seal (20) on piston (18) .
Illustration 9 g01333298
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
11. Install piston (18) . Use Tooling (B) and a suitable press in order to position piston (18) .
Use Tooling (C) in order to install retaining ring (19) . Carefully release the tension on
Tooling (B) .
5/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g01208920
12. Install clutch plates (16) and discs (17) . Install retaining ring (15) .
Illustration 11 g01209073
13. Position cover assembly (8) onto clutch housing assembly (11) .
Note: Make sure that the splines of cover assembly (8) fully engage all of the clutch plates
and discs in the clutch assembly.
6/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g01209125
Illustration 13 g01258534
Note: Caution is required while handling the lip seals. The lip seals can be damaged if
objects or cleaning fluids contact the sealing surface.
14. Use a suitable press in order to install bearing (14) . Use Tooling (A) in order to install
retaining ring (13) . Install lip seal (12) .
Illustration 14 g01333297
15. Position cover assembly (8) on the opposite side.
16. Install O-ring seal (10) on cover assembly (8) .
7/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g01208914
17. Position cover assembly (8) onto case (9) . Install bolts (7) and tighten bolts (7) to a
minimum torque of 18 N·m (13 lb ft) up to a maximum torque of 31 N·m (23 lb ft).
Illustration 16 g02092935
18. Apply Tooling (F) to the full diameter of the shoulder on drive flange (6) . Position new
sleeve (6A) on drive flange (6) . The external chamfer on sleeve (6A) will be on top. Use
Tooling (H) and a suitable press in order to install sleeve (6A) . Remove excess Tooling
(F) .
8/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g01333295
19. Install drive flange (6) and O-ring seal (5) .
Illustration 18 g01333292
20. Install retainer (4) . Tighten retainer (4) to a minimum torque of 610 N·m (450 lb ft) up to a
maximum torque of 750 N·m (550 lb ft). After achieving the torque range, overtighten
retainer (4) as needed in order to align the next position for locking screws (3) .
21. Install locking screws (3) and tighten locking screws (3) to a minimum torque of 7 N·m (62
lb in) to a maximum torque of 10 N·m (89 lb in).
9/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g01208862
22. Position sensor (1) . Install bolt (2) .
End By: Install the fan clutch. Refer to Disassembly and Assembly, "Fan Clutch - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:21:39 UTC+0800 2020
10/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04142231
Fan Drive - Assemble - Direct Drive
SMCS - 1359-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Illustration 1 g02341528
1. Install spring pin (6) into plate (7) .
2. Apply Tooling (A) to the threads of bolt (8). Install bearing assembly (2), spacer (3), hub
assembly (4), bearing assembly (5), plate (7), and bolt (8) onto bracket assembly (1).
Tighten bolt (8) to a torque of 115 ± 15 N·m (85 ± 11 lb ft).
1/2
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. End By: Install the fan drive (direct drive).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:22:35 UTC+0800 2020
2/2
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04108512
Water Pump - Remove and Install
SMCS - 1361-010; 1361-011; 1361-012
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Start By:
A. Remove the water temperature regulator.
B. Remove fan drive.
Illustration 1 g02310883
1/4
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 1. Remove bolts (1) and sheet assembly (2). Remove bolts (3) and sheet assembly (4) .
Illustration 2 g02311921
2. Remove step (6), sheet assembly (5), sheet assembly (7), and sheet assembly (8) .
Illustration 3 g02311923
Note: Open the hoods to the FULLY OPEN position.
3. Disconnect support assembly (9). Use suitable cribbing to support the support assembly (9) .
4. Remove support assembly (10) and support assembly (11) .
2/4
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g02311924
Note: Keep a minimum diameter bend of 102 mm (4.0 inch) for harness assemblies (13) .
5. Remove sheet assembly (15) and sheet assembly (16). Reposition sheet assembly (12) .
6. Remove hose (14) .
Illustration 5 g02311973
Illustration 6 g02311974
3/4
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 7. Remove bracket (14), tube (19), and elbow assembly (20) .
8. Remove bolts (22), water pump (21), and the O-ring seal.
Installation Procedure
1. Install water pump (21) in the reverse order of removal.
a. Lubricate the bore for the water pump (21) with lubricant that is being sealed.
b. Apply Tooling (A) to the threads of bolts (1) and (3) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:23:31 UTC+0800 2020
4/4
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04137389
Crankshaft Vibration Damper and Pulley - Remove and
Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2712 Guide Stud 2
Start By:
A. Remove the fan drive.
Illustration 1 g02334917
1/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 1. Remove bolts (2) and support (1). Disconnect bracket (3) .
Illustration 2 g02334920
2. Remove belt (4). Refer to the Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
3. Use two people to remove bracket assembly (6). The weight of bracket assembly (6) is
approximately 28 kg (62 lb). Remove bolts (5) and bracket assembly (6) .
Illustration 3 g02334921
4. Remove two bolts (9). Install Tooling (A).
5. Remove the remaining bolts (9). Remove pulley (11), adapter (10), pulley (8), and damper
assembly (7).
Installation Procedure
1. Install the crankshaft vibration damper and pulley in the reverse order of removal procedure.
Wed Sep 16 18:24:27 UTC+0800 2020
2/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04109121
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Start By:
A. Remove the crankshaft vibration damper and pulley.
Illustration 1 g01870637
Typical Example
1. Remove nuts (1) and crankshaft front seal (2) .
Installation Procedure
1. Install crankshaft front seal (2) in reverse order of removal.
1/2
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Note: Leave the shipping sleeve in place in order to install the crankshaft front seal. The
crankshaft front seal must be installed dry.
Illustration 2 g01870695
a. Tighten nuts (1) in a numerical sequence.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:25:22 UTC+0800 2020
2/2
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04109500
Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact skin.
1. Refer to Operation and Maintenance Manual, "Engine Oil and Oil Filter - Change" for the
correct draining and filling procedures.
1/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 1 g02312593
2. Remove bolts (1) and plate assemblies (4).
3. Remove bolts (2) and plate assembly (3) .
Illustration 2 g02312754
4. Disconnect clips (5) and (6) .
Illustration 3 g02312755
2/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 5. Disconnect harness assembly (7). Disconnect hose assembly (10).
6. Remove bolts (8) and lower engine oil pan (9) .
Illustration 4 g02312836
7. Remove bolts (11), bolts (13), and tube assembly (12).
8. Remove engine oil pan (9) .
Installation Procedure
1. Install engine oil pan (9) in reverse order of the removal.
a. Apply Tooling (A) to the threads of bolts (1) and (2) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:26:18 UTC+0800 2020
3/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04142771
Engine Front Mount - Remove and Install
SMCS - 1152-FR
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Personal injury can result from hot coolant, steam and alkali.
At operating temperature, engine coolant is hot and under pressure.
The radiator and all lines to heaters or the engine contain hot coolant or
steam. Any contact can cause severe burns.
Remove cooling system pressure cap slowly to relieve pressure only
when engine is stopped and cooling system pressure cap is cool enough
to touch with your bare hand.
Do not attempt to tighten hose connections when the coolant is hot, the
hose can come off causing burns.
Cooling System Coolant Additive contains alkali. Avoid contact with
skin and eyes.
1/7
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...