This document provides instructions for removing and installing a water pump on a 349E L excavator. The removal procedure involves: 1) Removing the water temperature regulator and fan drive; 2) Removing various sheet assemblies and supports; 3) Disconnecting support assemblies and repositioning harness assemblies; 4) Removing hoses. The installation procedure involves reversing the removal steps and applying threadlock to bolts.
This document provides instructions for assembling a torque converter for a 730 Articulated Truck. It lists 43 steps to assemble the various components of the torque converter in the correct order. Safety precautions are provided at the beginning regarding lifting heavy components and containing fluids. Diagrams illustrate each step. The summary ends by stating to connect the assembled torque converter housing to the planetary transmission.
Caterpillar cat 963 b track loader (prefix 9bl) service repair manual (9bl000...ujdjfjjskekmm
The document provides instructions for disassembling and assembling the air suspension system on a Caterpillar 963B track loader seat. It describes 22 steps to disassemble parts like the air spring, indicator, adjustment knob, and compressor. It then describes 19 steps to reassemble these parts in reverse order. Diagrams are provided to illustrate each step. Safety notices advise releasing air pressure before disassembly and wearing protective equipment when working with springs.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 345 c l hydraulic excavator (prefix pjw) service repair manua...hhfjksekmm
The document provides assembly instructions for a 345C excavator final drive system in 3 steps:
1. Adjust the bearing preload of the final drive by measuring dimensions and determining the correct shim thickness.
2. Assemble the carrier assemblies, which include installing planetary gears, bearings, shafts, and pins into housings.
3. Install the assembled carrier assemblies into the sprocket and ring gears in the correct order.
Caterpillar cat 319 d l excavator (prefix zca) service repair manual (zca0000...fjkskedmme
This document provides assembly instructions for a final drive on an excavator model 319D L. It involves 37 steps including installing bearings, seals, gears, and other components into housings and covers. Precise measurements and torque specifications are required. Cleanliness is important throughout the process. The completed final drive and sprocket assembly weighs approximately 310 kg.
Caterpillar cat 319 d l excavator (prefix kfm) service repair manual (kfm0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component. Some key steps in the disassembly include removing the cover, carrier assembly, ring gears, and separating internal planetary gears. Assembly involves installing bearings in the main housing, determining the correct shim thickness, installing seals, and reassembling internal components along with aligning the main housing to the motor housing. The instructions are detailed with illustrations and require specialized tools.
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Caterpillar cat 345 d l excavator (prefix jkn) service repair manual (jkn0000...hhfjksekmm
The document provides instructions for assembling a travel motor. It describes 33 steps to assemble parts like pistons, seals, plates, springs and valves. Measurements are checked with tools at several steps to ensure correct assembly. Cleaning parts and preventing contamination of hydraulic systems is emphasized.
This document provides instructions for assembling a torque converter for a 730 Articulated Truck. It lists 43 steps to assemble the various components of the torque converter in the correct order. Safety precautions are provided at the beginning regarding lifting heavy components and containing fluids. Diagrams illustrate each step. The summary ends by stating to connect the assembled torque converter housing to the planetary transmission.
Caterpillar cat 963 b track loader (prefix 9bl) service repair manual (9bl000...ujdjfjjskekmm
The document provides instructions for disassembling and assembling the air suspension system on a Caterpillar 963B track loader seat. It describes 22 steps to disassemble parts like the air spring, indicator, adjustment knob, and compressor. It then describes 19 steps to reassemble these parts in reverse order. Diagrams are provided to illustrate each step. Safety notices advise releasing air pressure before disassembly and wearing protective equipment when working with springs.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 345 c l hydraulic excavator (prefix pjw) service repair manua...hhfjksekmm
The document provides assembly instructions for a 345C excavator final drive system in 3 steps:
1. Adjust the bearing preload of the final drive by measuring dimensions and determining the correct shim thickness.
2. Assemble the carrier assemblies, which include installing planetary gears, bearings, shafts, and pins into housings.
3. Install the assembled carrier assemblies into the sprocket and ring gears in the correct order.
Caterpillar cat 319 d l excavator (prefix zca) service repair manual (zca0000...fjkskedmme
This document provides assembly instructions for a final drive on an excavator model 319D L. It involves 37 steps including installing bearings, seals, gears, and other components into housings and covers. Precise measurements and torque specifications are required. Cleanliness is important throughout the process. The completed final drive and sprocket assembly weighs approximately 310 kg.
Caterpillar cat 319 d l excavator (prefix kfm) service repair manual (kfm0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component. Some key steps in the disassembly include removing the cover, carrier assembly, ring gears, and separating internal planetary gears. Assembly involves installing bearings in the main housing, determining the correct shim thickness, installing seals, and reassembling internal components along with aligning the main housing to the motor housing. The instructions are detailed with illustrations and require specialized tools.
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Caterpillar cat 345 d l excavator (prefix jkn) service repair manual (jkn0000...hhfjksekmm
The document provides instructions for assembling a travel motor. It describes 33 steps to assemble parts like pistons, seals, plates, springs and valves. Measurements are checked with tools at several steps to ensure correct assembly. Cleaning parts and preventing contamination of hydraulic systems is emphasized.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 140 m 3 awd motor grader (prefix n9j) service repair manual (...ufjjsejfkskemme
This document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal process involves:
1. Removing the rear chassis support to access the pump.
2. Disconnecting hydraulic hoses and electrical harnesses from the pump.
3. Using lifting equipment to remove the 52 kg pump from the grader.
Reinstallation is the reverse of removal, including reconnecting hoses and harnesses and securing the pump with bolts. Proper cleaning and replacement of O-rings is emphasized to prevent contamination.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 349 f lxe excavator (prefix rax) service repair manual (rax00...fjsjjekdkme
The document provides instructions for disassembling and assembling the final drive of a 349F LXE excavator. The disassembly procedure involves removing 33 parts from the final drive including the ring gear, carrier assembly, planetary gears, and seals. The assembly procedure instructs installing 52 parts in the reverse order and specifies torque specifications and lubricants to apply during assembly. Tools required include lifting devices, punches, and seal installation tools.
Caterpillar cat 730 c articulated truck (prefix tff) service repair manual (t...ufjjsekkemmd
The document provides instructions for disassembling and assembling the torque converter of a 730C articulated truck. It lists 18 steps for disassembly, which include removing housing assemblies, bearings, plates, discs, seals and other internal components. It then lists 15 steps for assembly, which describe installing components in reverse order and include details on tooling used and proper torque specifications. The instructions note to keep parts clean from contaminants to prevent wear and shortened life.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fjjsjeskkekem
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f8uejkdkdmm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fuusejkddmmd3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujsekmd9idd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...shibi1322
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...fucheng89
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdksmmdmdd
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdkskmmdd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...8foskkdjdkdm3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...jiazhi27185
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujkse9didkke3
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...didkkskdmmd
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection from contamination during installation is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...km7seyrduhdw
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...yin9niaojiao
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 140 m 3 awd motor grader (prefix n9j) service repair manual (...ufjjsejfkskemme
This document provides instructions for removing and installing a piston pump from a Caterpillar 140M 3 AWD motor grader. The removal process involves:
1. Removing the rear chassis support to access the pump.
2. Disconnecting hydraulic hoses and electrical harnesses from the pump.
3. Using lifting equipment to remove the 52 kg pump from the grader.
Reinstallation is the reverse of removal, including reconnecting hoses and harnesses and securing the pump with bolts. Proper cleaning and replacement of O-rings is emphasized to prevent contamination.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 349 f lxe excavator (prefix rax) service repair manual (rax00...fjsjjekdkme
The document provides instructions for disassembling and assembling the final drive of a 349F LXE excavator. The disassembly procedure involves removing 33 parts from the final drive including the ring gear, carrier assembly, planetary gears, and seals. The assembly procedure instructs installing 52 parts in the reverse order and specifies torque specifications and lubricants to apply during assembly. Tools required include lifting devices, punches, and seal installation tools.
Caterpillar cat 730 c articulated truck (prefix tff) service repair manual (t...ufjjsekkemmd
The document provides instructions for disassembling and assembling the torque converter of a 730C articulated truck. It lists 18 steps for disassembly, which include removing housing assemblies, bearings, plates, discs, seals and other internal components. It then lists 15 steps for assembly, which describe installing components in reverse order and include details on tooling used and proper torque specifications. The instructions note to keep parts clean from contaminants to prevent wear and shortened life.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat d11 t track type tractor dozer bulldozer (prefix mdg) service...fjjsjeskkekem
This document provides assembly instructions for a final drive on a D11T track-type tractor. It lists 37 steps and required tools to assemble the final drive components which include installing bearings and seals using specialized tools, torquing bolts to specified values, and checking clearances with feeler gauges. Pictures accompany each step to illustrate the assembly process.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f8uejkdkdmm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fuusejkddmmd3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujsekmd9idd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...shibi1322
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...fucheng89
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdksmmdmdd
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdkskmmdd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...8foskkdjdkdm3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...jiazhi27185
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujkse9didkke3
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...didkkskdmmd
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection from contamination during installation is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...km7seyrduhdw
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...yin9niaojiao
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...orrf0370383
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...fjskekxcddmmme
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...cdsaas
The document provides instructions for assembling a travel motor. It describes 33 steps for installing various components like seals, pistons, plates, and bearings. Measurements are taken throughout to ensure proper assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system. The travel motor must be filled with the correct oil type before operation to prevent damage.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...hhfjksekmm
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection from contamination during installation is emphasized.
Caterpillar cat 349 d l excavator (prefix gkf) service repair manual (gkf0000...fjjseksxckmdme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions to contain fluids. The procedure describes attaching a lifting device to the travel motor and removing bolts and hose assemblies to detach the travel motor from the excavator.
Similar to Caterpillar cat 349 e l excavator (prefix mpz) service repair manual (mpz00001 and up) (19)
Caterpillar cat 349 d2 l excavator (prefix sdm) service repair manual (sdm000...didkkskdmmd
The document provides instructions for disassembling a travel motor. It lists 30 steps to remove parts like the head, plates, seals, pistons, and housing. Tools include eyebolts, pullers, drivers, and presses. Removed parts must be cleaned and reinstalled in their original positions and orientations during reassembly to avoid damaging components. Safety notices warn of risks like fluids, springs, and heavy lifting.
Caterpillar cat 349 d2 l excavator (prefix ran) service repair manual (ran000...didkkskdmmd
The document provides instructions for disassembling a travel motor. It lists the required tools and gives step-by-step instructions to remove parts like the head, plates, seals, pins, bearing, and more. Safety notices are included to handle parts carefully, avoid damage, clean components properly, and contain fluids.
Caterpillar cat 349 d2 l excavator (prefix pfd) service repair manual (pfd000...didkkskdmmd
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pistons, and housing. Tools include eyebolts, pullers, drivers, and presses. Removed parts must be cleaned and reinstalled in their original positions and orientations during reassembly.
Caterpillar cat 349 d2 l excavator (prefix gax) service repair manual (gax000...didkkskdmmd
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and more. Identification marks should be made on matching parts for reassembly. Cleanliness is important to prevent contamination. The assembly process reverses the disassembly steps.
This document provides instructions for removing and installing the rear gear group on a 349D2 and 349D2 L excavator powered by a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, bushings and bearings. The installation procedure involves 12 steps including lowering temperatures of bearings before installation, applying sealant to bolts, and ensuring proper dimensions are met. Tools including drivers and installer are required.
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pistons, and housing. Precautions are outlined to prevent contamination and ensure proper installation of parts in their original locations. The assembly section instructs installation of components in reverse order and includes applying sealant and lubricant.
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 29 steps for assembly, installing components like seals, pistons, plates, and housing in reverse order of disassembly. Tools required are listed in a table. Cautions are provided about cleanliness, contamination, marking parts locations, and applying lubricant before assembly.
The document provides instructions for disassembling a travel motor. It lists the required tools and gives step-by-step instructions to remove parts like the head, plates, seals, pins, bearing, and piston. Safety notices are included to handle parts carefully, avoid damage, clean components properly, and contain fluids.
The document provides instructions for disassembling a travel motor. It lists 30 steps to remove parts like the head, plates, seals, pistons, and housing. Tools include eyebolts, pullers, drivers, and presses. Removed parts must be cleaned and reinstalled in their original positions and orientations during reassembly to avoid damaging components. Safety notices warn of risks like fluids, springs, and heavy lifting.
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pistons, and housing. Tools include eyebolts, pullers, drivers, and presses. Removed parts must be cleaned and reinstalled in their original positions and orientations during reassembly.
The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and more. The instructions note to mark parts locations and orientations. Reassembly follows the reverse order, and cautions are provided to avoid damage and contamination.
Caterpillar cat 349 d l mobile hydraulic excavator (prefix dkn) service repai...didkkskdmmd
The document provides instructions for disassembling a travel motor. It begins by removing the displacement change valve and O-rings from the motor head. Several plugs, bolts, and seals are then removed from the head and housing. Pins and plates are taken out, and bearing pullers are used to remove internal components like bearings. The rotating group, piston assemblies, seals, and other pieces are dismantled using various tools. Detailed steps and illustrations guide the disassembly process.
Caterpillar cat 349 d l excavator (prefix wtd) service repair manual (wtd0000...didkkskdmmd
The document provides instructions for assembling a travel motor. It lists the required tools and begins by noting the importance of cleanliness. It then provides 33 steps describing how to install seals, spacers, pistons, disks, bearings and other components into the travel motor housing and barrel. It concludes by stating the travel motor should be filled with the correct oil specification prior to operation.
Caterpillar cat 349 d l excavator (prefix rbj) service repair manual (rbj0000...didkkskdmmd
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, disks, piston assemblies, seals and more. Special tools are required to remove some parts and care must be taken to prevent damage and contamination. All parts must be cleaned and reinstalled in their original locations and orientations.
Caterpillar cat 349 d l excavator (prefix pzg) service repair manual (pzg0000...didkkskdmmd
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions for removing components like the head, plates, disks, piston assemblies, seals and more. Special care must be taken to clean parts and ensure they are reinstalled in their original locations and orientations. Proper assembly prevents damage and contamination issues.
Caterpillar cat 349 d l excavator (prefix nnf) service repair manual (nnf0000...didkkskdmmd
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, disks, seals and more. It then lists 28 steps for assembly, installing components like seals, spacers, washers, pistons and plugs in the reverse order of disassembly. Precautions are provided to keep parts clean and properly identify components during disassembly and reassembly.
Caterpillar cat 349 d l excavator (prefix men) service repair manual (men0000...didkkskdmmd
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 13 steps for assembly, including installing seals, spacers, pistons, housing, and tightening components. Required tools include eyebolts, pullers, drivers, and seals. Cleanliness is emphasized to prevent contamination of hydraulic components.
Caterpillar cat 349 d l excavator (prefix klh) service repair manual (klh0000...didkkskdmmd
The document provides step-by-step instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pistons, housing and more. Special tools are required to remove some parts and precautions must be taken when handling springs or heavy components. Each part is to be cleaned and inspected, replacing any that are worn or damaged.
Caterpillar cat 349 d l excavator (prefix jgb) service repair manual (jgb0000...didkkskdmmd
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, plates, disks, seals and pistons. It also provides notes about cleaning parts, applying lubricant, and ensuring components are reinstalled in their original locations during assembly. The assembly instructions list the components and their order of installation back into the travel motor housing.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i06192451
Fan Drive - Assemble - Hydraulic Fan Drive
SMCS - 1359-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1861 Retaining Ring Pliers 1
B 9U-7480 Compressing Tube 1
C 1P-1859 Retaining Ring Pliers 1
D 1P-1863 Retaining Ring Pliers 1
E - Loctite Flexible Anaerobic Gasket Flange 1
F - Loctite 648 1
G 359-4915 Driver 1
H 359-4916 Driver 1
Note: Caution is required while handling the lip seals. The lip seals can be damaged if objects or
cleaning fluids contact the sealing surface.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts except the lip
seals with cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to
dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If
any parts are worn or damaged, use new parts for replacement.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
1/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01333314
1. Use a suitable press to install bearing (29) into case (9) . Use Tooling (A) in order to install
retaining ring (28) .
Illustration 2 g01333310
Note: Caution is required while handling the lip seals. The lip seals can be damaged if
objects or cleaning fluids contact the sealing surface.
2. Apply Tooling (E) to the outside diameter of lip seal (27) . Carefully install lip seal (27) into
case (9) .
2/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g02092525
3. Install seal (25) onto shaft assembly (24) .
4. Apply Tooling (F) to the full diameter of the shoulder on shaft assembly (24) . Position new
sleeve (30) on shaft assembly (24) . The external chamfer on sleeve (30) will be on top. Use
Tooling (G) and a suitable press in order to install sleeve (30) . Remove excess Tooling (F) .
Illustration 4 g01333308
Illustration 5 g01286111
3/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 5. Position tube assembly (26) into case (9) .
6. Position case (9) and tube assembly (26) onto shaft assembly (24) .
7. Use a suitable press and a suitable driver to press shaft assembly (24) through the bearing
and through tube assembly (26) .
Illustration 6 g01333303
8. Use Tooling (D) in order to install retaining ring (23) . Install seal rings (22) onto shaft
assembly (24) .
Illustration 7 g01333301
9. Install spring (21) on clutch housing assembly (11) .
4/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g01333300
10. Install seal (20) on piston (18) .
Illustration 9 g01333298
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
11. Install piston (18) . Use Tooling (B) and a suitable press in order to position piston (18) .
Use Tooling (C) in order to install retaining ring (19) . Carefully release the tension on
Tooling (B) .
5/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g01208920
12. Install clutch plates (16) and discs (17) . Install retaining ring (15) .
Illustration 11 g01209073
13. Position cover assembly (8) onto clutch housing assembly (11) .
Note: Make sure that the splines of cover assembly (8) fully engage all of the clutch plates
and discs in the clutch assembly.
6/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g01209125
Illustration 13 g01258534
Note: Caution is required while handling the lip seals. The lip seals can be damaged if
objects or cleaning fluids contact the sealing surface.
14. Use a suitable press in order to install bearing (14) . Use Tooling (A) in order to install
retaining ring (13) . Install lip seal (12) .
Illustration 14 g01333297
15. Position cover assembly (8) on the opposite side.
16. Install O-ring seal (10) on cover assembly (8) .
7/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g01208914
17. Position cover assembly (8) onto case (9) . Install bolts (7) and tighten bolts (7) to a
minimum torque of 18 N·m (13 lb ft) up to a maximum torque of 31 N·m (23 lb ft).
Illustration 16 g02092935
18. Apply Tooling (F) to the full diameter of the shoulder on drive flange (6) . Position new
sleeve (6A) on drive flange (6) . The external chamfer on sleeve (6A) will be on top. Use
Tooling (H) and a suitable press in order to install sleeve (6A) . Remove excess Tooling
(F) .
8/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g01333295
19. Install drive flange (6) and O-ring seal (5) .
Illustration 18 g01333292
20. Install retainer (4) . Tighten retainer (4) to a minimum torque of 610 N·m (450 lb ft) up to a
maximum torque of 750 N·m (550 lb ft). After achieving the torque range, overtighten
retainer (4) as needed in order to align the next position for locking screws (3) .
21. Install locking screws (3) and tighten locking screws (3) to a minimum torque of 7 N·m (62
lb in) to a maximum torque of 10 N·m (89 lb in).
9/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g01208862
22. Position sensor (1) . Install bolt (2) .
End By: Install the fan clutch. Refer to Disassembly and Assembly, "Fan Clutch - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:21:39 UTC+0800 2020
10/10
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04142231
Fan Drive - Assemble - Direct Drive
SMCS - 1359-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Illustration 1 g02341528
1. Install spring pin (6) into plate (7) .
2. Apply Tooling (A) to the threads of bolt (8). Install bearing assembly (2), spacer (3), hub
assembly (4), bearing assembly (5), plate (7), and bolt (8) onto bracket assembly (1).
Tighten bolt (8) to a torque of 115 ± 15 N·m (85 ± 11 lb ft).
1/2
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. End By: Install the fan drive (direct drive).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:22:35 UTC+0800 2020
2/2
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04108512
Water Pump - Remove and Install
SMCS - 1361-010; 1361-011; 1361-012
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Start By:
A. Remove the water temperature regulator.
B. Remove fan drive.
Illustration 1 g02310883
1/4
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 1. Remove bolts (1) and sheet assembly (2). Remove bolts (3) and sheet assembly (4) .
Illustration 2 g02311921
2. Remove step (6), sheet assembly (5), sheet assembly (7), and sheet assembly (8) .
Illustration 3 g02311923
Note: Open the hoods to the FULLY OPEN position.
3. Disconnect support assembly (9). Use suitable cribbing to support the support assembly (9) .
4. Remove support assembly (10) and support assembly (11) .
2/4
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g02311924
Note: Keep a minimum diameter bend of 102 mm (4.0 inch) for harness assemblies (13) .
5. Remove sheet assembly (15) and sheet assembly (16). Reposition sheet assembly (12) .
6. Remove hose (14) .
Illustration 5 g02311973
Illustration 6 g02311974
3/4
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 7. Remove bracket (14), tube (19), and elbow assembly (20) .
8. Remove bolts (22), water pump (21), and the O-ring seal.
Installation Procedure
1. Install water pump (21) in the reverse order of removal.
a. Lubricate the bore for the water pump (21) with lubricant that is being sealed.
b. Apply Tooling (A) to the threads of bolts (1) and (3) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:23:31 UTC+0800 2020
4/4
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04137389
Crankshaft Vibration Damper and Pulley - Remove and
Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2712 Guide Stud 2
Start By:
A. Remove the fan drive.
Illustration 1 g02334917
1/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 1. Remove bolts (2) and support (1). Disconnect bracket (3) .
Illustration 2 g02334920
2. Remove belt (4). Refer to the Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
3. Use two people to remove bracket assembly (6). The weight of bracket assembly (6) is
approximately 28 kg (62 lb). Remove bolts (5) and bracket assembly (6) .
Illustration 3 g02334921
4. Remove two bolts (9). Install Tooling (A).
5. Remove the remaining bolts (9). Remove pulley (11), adapter (10), pulley (8), and damper
assembly (7).
Installation Procedure
1. Install the crankshaft vibration damper and pulley in the reverse order of removal procedure.
Wed Sep 16 18:24:27 UTC+0800 2020
2/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04109121
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Start By:
A. Remove the crankshaft vibration damper and pulley.
Illustration 1 g01870637
Typical Example
1. Remove nuts (1) and crankshaft front seal (2) .
Installation Procedure
1. Install crankshaft front seal (2) in reverse order of removal.
1/2
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Note: Leave the shipping sleeve in place in order to install the crankshaft front seal. The
crankshaft front seal must be installed dry.
Illustration 2 g01870695
a. Tighten nuts (1) in a numerical sequence.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:25:22 UTC+0800 2020
2/2
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04109500
Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact skin.
1. Refer to Operation and Maintenance Manual, "Engine Oil and Oil Filter - Change" for the
correct draining and filling procedures.
1/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 1 g02312593
2. Remove bolts (1) and plate assemblies (4).
3. Remove bolts (2) and plate assembly (3) .
Illustration 2 g02312754
4. Disconnect clips (5) and (6) .
Illustration 3 g02312755
2/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 5. Disconnect harness assembly (7). Disconnect hose assembly (10).
6. Remove bolts (8) and lower engine oil pan (9) .
Illustration 4 g02312836
7. Remove bolts (11), bolts (13), and tube assembly (12).
8. Remove engine oil pan (9) .
Installation Procedure
1. Install engine oil pan (9) in reverse order of the removal.
a. Apply Tooling (A) to the threads of bolts (1) and (2) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 16 18:26:18 UTC+0800 2020
3/3
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349E L EXCAVATOR MPZ
Configuration: 349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
349E Excavator and 349E MHPU
Mobile Hydraulic Power Unit C13 Engine Supplement
Media Number -KENR9847-03 Publication Date -01/01/2013 Date Updated -28/01/2013
i04142771
Engine Front Mount - Remove and Install
SMCS - 1152-FR
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 242 -
Personal injury can result from hot coolant, steam and alkali.
At operating temperature, engine coolant is hot and under pressure.
The radiator and all lines to heaters or the engine contain hot coolant or
steam. Any contact can cause severe burns.
Remove cooling system pressure cap slowly to relieve pressure only
when engine is stopped and cooling system pressure cap is cool enough
to touch with your bare hand.
Do not attempt to tighten hose connections when the coolant is hot, the
hose can come off causing burns.
Cooling System Coolant Additive contains alkali. Avoid contact with
skin and eyes.
1/7
349E L Excavators MPZ00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/9/16
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...