The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions to contain fluids. The procedure describes attaching a lifting device to the travel motor and removing bolts and hose assemblies to detach the travel motor from the excavator.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...cdsaas
The document provides instructions for assembling a travel motor. It describes 33 steps for installing various components like seals, pistons, plates, and bearings. Measurements are taken throughout to ensure proper assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system. The travel motor must be filled with the correct oil type before operation to prevent damage.
Caterpillar cat 345 d l excavator (prefix mlk) service repair manual (mlk0000...hhfjksekmm
This document provides instructions for installing a travel motor. It outlines 33 steps for assembling components like seals, pistons, plates, and valves. Measurements are checked at several points to ensure proper assembly. The motor is filled with oil after installation to prevent damage during operation.
Caterpillar cat 349 d2 l excavator (prefix yae) service repair manual (yae000...cdsaas
The document provides instructions for assembling and installing a travel motor. It outlines 33 steps for assembling components like pistons, seals, plates, and bearings. Measurement checks are specified to ensure proper assembly. Tools required are listed. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 345 d l excavator (prefix jkn) service repair manual (jkn0000...hhfjksekmm
The document provides instructions for assembling a travel motor. It describes 33 steps to assemble parts like pistons, seals, plates, springs and valves. Measurements are checked with tools at several steps to ensure correct assembly. Cleaning parts and preventing contamination of hydraulic systems is emphasized.
Caterpillar cat 336 d l excavator (prefix kdj) service repair manual (kdj0000...fjskekdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) from a Caterpillar 336D L excavator. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. Tools include drivers, pliers, pullers and indicators to install components properly.
Caterpillar cat 336 d l excavator (prefix ppn) service repair manual (ppn0000...fjskekdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) for a 336D L & 336D LN excavator. The disassembly procedure involves 30 steps that remove components like the head, port plate, bearing cups, pistons, pins, and springs. The assembly procedure involves 25 steps that install components in the reverse order, and notes that cleanliness is important during assembly. Tools required include retaining ring pliers, a dial indicator, and a bearing puller.
Caterpillar cat 329 d2 and 329d2l excavator (prefix rga) service repair manua...udjfjjsekekkem
This document provides instructions for disassembling and assembling the swing motor of a Caterpillar 329D2 excavator. The disassembly procedure involves removing 27 parts in a specific order, taking care with spring-loaded components. The assembly procedure similarly involves installing the 27 parts in reverse order and also notes that O-rings, gaskets, and seals should be replaced and components should be cleaned before assembly. Torque specifications and required tools are provided for referenced steps.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...cdsaas
The document provides instructions for assembling a travel motor. It describes 33 steps for installing various components like seals, pistons, plates, and bearings. Measurements are taken throughout to ensure proper assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system. The travel motor must be filled with the correct oil type before operation to prevent damage.
Caterpillar cat 345 d l excavator (prefix mlk) service repair manual (mlk0000...hhfjksekmm
This document provides instructions for installing a travel motor. It outlines 33 steps for assembling components like seals, pistons, plates, and valves. Measurements are checked at several points to ensure proper assembly. The motor is filled with oil after installation to prevent damage during operation.
Caterpillar cat 349 d2 l excavator (prefix yae) service repair manual (yae000...cdsaas
The document provides instructions for assembling and installing a travel motor. It outlines 33 steps for assembling components like pistons, seals, plates, and bearings. Measurement checks are specified to ensure proper assembly. Tools required are listed. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 345 d l excavator (prefix jkn) service repair manual (jkn0000...hhfjksekmm
The document provides instructions for assembling a travel motor. It describes 33 steps to assemble parts like pistons, seals, plates, springs and valves. Measurements are checked with tools at several steps to ensure correct assembly. Cleaning parts and preventing contamination of hydraulic systems is emphasized.
Caterpillar cat 336 d l excavator (prefix kdj) service repair manual (kdj0000...fjskekdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) from a Caterpillar 336D L excavator. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. Tools include drivers, pliers, pullers and indicators to install components properly.
Caterpillar cat 336 d l excavator (prefix ppn) service repair manual (ppn0000...fjskekdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) for a 336D L & 336D LN excavator. The disassembly procedure involves 30 steps that remove components like the head, port plate, bearing cups, pistons, pins, and springs. The assembly procedure involves 25 steps that install components in the reverse order, and notes that cleanliness is important during assembly. Tools required include retaining ring pliers, a dial indicator, and a bearing puller.
Caterpillar cat 329 d2 and 329d2l excavator (prefix rga) service repair manua...udjfjjsekekkem
This document provides instructions for disassembling and assembling the swing motor of a Caterpillar 329D2 excavator. The disassembly procedure involves removing 27 parts in a specific order, taking care with spring-loaded components. The assembly procedure similarly involves installing the 27 parts in reverse order and also notes that O-rings, gaskets, and seals should be replaced and components should be cleaned before assembly. Torque specifications and required tools are provided for referenced steps.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat 336 e lh excavator (prefix gny) service repair manual (gny000...fjskekdmjekm
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 329 d l excavator (prefix wdk) service repair manual (wdk0000...ufjsjekfksemm
This document provides removal and assembly procedures for a travel motor on Caterpillar 329D and 329D L excavators. The removal procedure involves draining fluid, disconnecting hoses, removing bolts and pulling the travel motor out of the final drive. Disassembly of the travel motor requires removing the head, port plate, bearings, seals, springs, brake piston and various other internal components using specialized tools. The assembly procedure instructs to replace all seals and gaskets, clean all parts thoroughly, and install components in reverse order of removal while applying a film of oil. Proper cleanliness and torque specifications are emphasized throughout.
Caterpillar cat 336 f l excavator (prefix ljy) service repair manual (ljy0000...fjkskedmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 323 e l excavator (prefix rap) service repair manual (rap0000...fjskefkemms
The document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes steps to disassemble and remove the final drive components, such as the carrier assembly, ring gears, planetary gears, and seals. It also provides instructions for assembling the final drive, including pressing bearings into place, determining the correct shim thickness, installing seals and pins, and reassembling the carrier assembly. Tools required include lifting devices, presses, seal installers, and other specialized tools. Proper torque values and procedures are specified for reinstalling components.
Caterpillar cat 352 f excavator (prefix ndc) service repair manual (ndc00001 ...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor of a 352F excavator. It begins by describing how to safely remove the travel motor and various components using specialized tools. Detailed steps are provided to disassemble the motor head assembly, barrel assembly, piston assemblies, and other internal parts. Specifications and torque values are included for reassembly. The process concludes with lubricating and installing components in reverse order.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
The document provides instructions for removing and installing various engine components on a Caterpillar C9.3B industrial engine. It includes steps for removing and installing the crankshaft rear seal, flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, and housing (front). Diagrams and part numbers for required tools are provided for each procedure. The document is part of a service manual for Caterpillar technicians repairing C9.3B engines.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...fkjsekksmem
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f8uejkdkdmm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fuusejkddmmd3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujsekmd9idd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...shibi1322
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...fucheng89
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdksmmdmdd
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdkskmmdd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...8foskkdjdkdm3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...jiazhi27185
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujkse9didkke3
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...didkkskdmmd
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection from contamination during installation is emphasized.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat 336 e lh excavator (prefix gny) service repair manual (gny000...fjskekdmjekm
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 329 d l excavator (prefix wdk) service repair manual (wdk0000...ufjsjekfksemm
This document provides removal and assembly procedures for a travel motor on Caterpillar 329D and 329D L excavators. The removal procedure involves draining fluid, disconnecting hoses, removing bolts and pulling the travel motor out of the final drive. Disassembly of the travel motor requires removing the head, port plate, bearings, seals, springs, brake piston and various other internal components using specialized tools. The assembly procedure instructs to replace all seals and gaskets, clean all parts thoroughly, and install components in reverse order of removal while applying a film of oil. Proper cleanliness and torque specifications are emphasized throughout.
Caterpillar cat 336 f l excavator (prefix ljy) service repair manual (ljy0000...fjkskedmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 323 e l excavator (prefix rap) service repair manual (rap0000...fjskefkemms
The document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes steps to disassemble and remove the final drive components, such as the carrier assembly, ring gears, planetary gears, and seals. It also provides instructions for assembling the final drive, including pressing bearings into place, determining the correct shim thickness, installing seals and pins, and reassembling the carrier assembly. Tools required include lifting devices, presses, seal installers, and other specialized tools. Proper torque values and procedures are specified for reinstalling components.
Caterpillar cat 352 f excavator (prefix ndc) service repair manual (ndc00001 ...fjsjjekdkme
This document provides instructions for disassembling and assembling the travel motor of a 352F excavator. It begins by describing how to safely remove the travel motor and various components using specialized tools. Detailed steps are provided to disassemble the motor head assembly, barrel assembly, piston assemblies, and other internal parts. Specifications and torque values are included for reassembly. The process concludes with lubricating and installing components in reverse order.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
The document provides instructions for removing and installing various engine components on a Caterpillar C9.3B industrial engine. It includes steps for removing and installing the crankshaft rear seal, flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, and housing (front). Diagrams and part numbers for required tools are provided for each procedure. The document is part of a service manual for Caterpillar technicians repairing C9.3B engines.
Caterpillar cat 329 d excavator (prefix yfw) service repair manual (yfw00001 ...fkjsekksmem
This document provides instructions for disassembling and assembling the final drive of a 329D or 329D L excavator. It lists 37 steps for disassembly, removing components like gears, shafts, bearings and seals. The assembly section outlines 15 steps, including pressing bearings into place, installing seals, and using shims to set the proper bearing preload when mounting the main housing onto the motor housing. Cleanliness is emphasized throughout as important for preventing contamination.
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f8uejkdkdmm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fuusejkddmmd3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujsekmd9idd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...shibi1322
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...fucheng89
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdksmmdmdd
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...jdkskmmdd
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...8foskkdjdkdm3e
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...jiazhi27185
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...fujkse9didkke3
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...didkkskdmmd
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection from contamination during installation is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...km7seyrduhdw
The document provides instructions for assembling a travel motor. It describes 33 steps for installing parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...yin9niaojiao
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual (KHS00001...orrf0370383
The document provides instructions for assembling a travel motor. It describes 33 steps to install parts like seals, pistons, plates, and bearings. Measurements are checked with tools at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Similar to Caterpillar cat 349 d excavator (prefix gkf) service repair manual (gkf00001 and up) (15)
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...fjjseksxckmdme
This document provides instructions for disassembling and assembling the front axle of an M315C Wheeled Excavator. It begins with required tools and safety information. The 27 step disassembly process removes components like the carrier housing, planetary gears, brake assembly and bearings. The 22 step assembly process then rebuilds these components in reverse order, noting specifics like torque values and seal/bushing installation procedures. Precise assembly is required to properly rebuild the front axle.
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. Detailed steps describe each part removal and installation to correctly reassemble the travel motor.
This document provides instructions for removing and installing a swing motor and swing drive on an M315 excavator. It describes releasing hydraulic pressure, draining oil, disconnecting hoses, and removing and installing various components like bolts, seals, and motors. Safety precautions are provided regarding containing fluids, releasing pressure, and preventing personal injury. Detailed step-by-step instructions are given for disassembly and reassembly.
Caterpillar cat d6 r track type tractor (prefix 6jn) service repair manual (6...fjjseksxckmdme
This document provides assembly instructions for a Flexxaire fan on a D6R track-type tractor. It describes assembling the shifter block, hub, actuator bearings, carrier/spool, main bearing, and installing components like the O-ring and frost plug. The multi-step process involves placing various parts like bearings, washers, spacers and seals in the correct orientation and securing them with locknuts, applying thread lock compounds and grease. Tolerances and torque specifications are provided.
Caterpillar cat d6 r track type tractor (prefix 6hr) service repair manual (6...fjjseksxckmdme
1) The document provides instructions for removing and installing front track roller frames and recoil springs on a D6R track-type tractor.
2) It describes using various tooling to gradually compress the recoil springs and remove the retainer in increments to avoid injury.
3) Fifteen steps are outlined for installing the front track roller frame back onto the rear frame.
Caterpillar cat d6 r track type tractor (prefix 6gr) service repair manual (6...fjjseksxckmdme
The document provides instructions for removing and installing components of a D6R track-type tractor, including:
1) Removing the hydraulic control valve by draining hydraulic fluid, disconnecting hoses, and removing mounting bolts.
2) Disassembling the implement pump by removing mounting components, pistons, seals, and bearings.
3) Removing the hydraulic control linkage by disconnecting rods and removing mounting bolts, panels, and handles.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjjseksxckmdme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before installation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
Caterpillar cat d6 r track type tractor (prefix 5rr) service repair manual (5...fjjseksxckmdme
The document provides instructions for removing and installing various engine components on a Caterpillar D6R track-type tractor, including:
1. Removing and installing the spacer plate, which involves removing seals and gaskets.
2. Removing and installing water directors by removing them from the cylinder head and pressing new ones in at a specified depth.
3. Removing and installing the lifter group using a magnetic tool and checking lifter diameters.
4. Removing and installing the camshaft by aligning timing marks, removing bolts and gears, cleaning parts, and reinstalling with lubricant while rotating to prevent binding.
Caterpillar cat d6 r track type tractor (prefix 5pr) service repair manual (5...fjjseksxckmdme
The document provides instructions for removing and installing a spacer plate on a D6R track-type tractor with a 3306 engine. It describes removing the cylinder head, O-rings, seals, and spacer plate. It then details cleaning surfaces, installing new gaskets and seals, and reinstalling the spacer plate and cylinder head. The process also includes checking cylinder liner projection after installation.
Caterpillar cat d6 r track type tractor (prefix 5ln) service repair manual (5...fjjseksxckmdme
This document provides instructions for disassembling and assembling components of the fuel injection system for Caterpillar 3304B and 3306B engines. It describes how to disassemble the governor by removing the fuel ratio control and mounting bolts. Proper cleaning of parts to prevent contamination is emphasized. The assembly procedure explains how to install bearings and other components in the fuel injection pump housing using various tools, and how to set the timing when installing the pump and governor.
Caterpillar cat d6 r track type tractor (prefix 4wr) service repair manual (4...fjjseksxckmdme
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include draining oil, removing covers and shafts, using lifting tools to remove heavy components, and reinstalling parts in reverse order while applying new seals and grease. Detailed diagrams show tooling and component locations to aid the process.
The document provides removal and installation instructions for a precooler, water temperature regulator housing, water pump, and other engine components. It includes illustrations and lists required tools. The procedures describe disconnecting hoses and harness assemblies, removing bolts and parts like housings and manifolds, and installing components in the reverse order of removal while applying sealant compounds and ensuring cleanliness. Cautions are provided about containing fluids and preventing contamination.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting parts before installation and applying thread locking compound to bolts.
2. Installing the front plate, gears, and shafts in the correct order and orientation while adjusting backlash.
3. Torquing bolts and nuts to specified values after applying thread locking compound.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page service manual excerpt that describes:
1) Required tools and safety notices
2) Removal procedure which includes supporting the engine, removing bolts and lifting the housing off
3) Installation procedure which includes cleaning, applying sealant, positioning the housing and tightening bolts in a specific sequence and torque.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
This document provides disassembly and assembly instructions for a C18 industrial engine pump drive. It describes in detail how to disassemble and assemble the integral pump drive of a CX38-P892 petroleum transmission. The 19 step disassembly procedure includes removing bolts, gears, bearings, seals and other components. The 23 step assembly procedure describes cleaning parts and installing components in reverse order, paying attention to torque specifications and end play measurements. Tools required include lifting devices, pullers, indicators and other specialized tools.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and step-by-step procedures describing how to remove and install each component, with illustrations showing the parts.
3) Safety and cleaning notes are provided throughout to keep parts clean and avoid damage during disassembly and assembly.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Fuel priming pump removal and installation procedures in 3 steps.
- Fuel filter base removal procedure in 5 steps and disassembly procedure in 4 steps.
- Fuel filter base assembly procedure in 4 steps and installation procedure in 6 steps.
- Fuel transfer pump removal procedure in 6 steps and installation procedure in 7 steps.
- Electronic unit injector removal procedure with 5 steps requiring identification marks for installation.
Caterpillar cat 349 d l excavator (prefix gkf) service repair manual (gkf0000...fjjseksxckmdme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions to contain fluids. The procedure describes attaching a lifting device to the travel motor and removing bolts and hose assemblies to detach the travel motor from the excavator.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D EXCAVATOR GKF
Configuration: 349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile
Hydraulic Power Units Machine Systems
Media Number -RENR9574-10 Publication Date -01/08/2014 Date Updated -18/09/2018
i03778971
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 3E-3879 Eyebolt 1
D 4C-8359 Eyebolt 1
F 1P-1862 Pliers 1
G 1P-0510 Driver Group 1
J 4C-4030 Thread Lock Compound 1
K 180-6533 Seal Driver 1
L 6V-7030 Micrometer Depth Gauge 1
M 8T-0447 Calipers 1
N 1U-6396 O-Ring Assembly Compound 1
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
1/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline For Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
Note: O-ring seals , gaskets, and seals should always be replaced. A used O-ring seal may not
have the same sealing properties as a new O-ring seal. Use Tooling (H) during the assembly
procedure.
Note: Apply a light film of "10W" oil to all components before assembly.
Illustration 1 g01204890
1. Install O-ring seal (34) on plug (33).
2. Install piston (32) and the plug in the travel motor body. Tighten the plug to a torque of
430 ± 40 N·m (317 ± 30 lb ft).
2/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g01204916
Illustration 3 g01204919
3. Apply a thin coat of Tooling (J) on the outer surfaces of lip seal (31).
4. Use Tooling (K) and a suitable hammer to drive the lip seal into the travel motor body.
Drive the seal downward until Tooling (K) makes contact with the travel motor housing.
5. Use Tooling (F) to install retaining ring (30) to the shaft end of the travel motor body.
Illustration 4 g01204923
6. Install keys (29) inside the travel motor body.
3/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 5 g01204924
7. Assemble washers (25), inner spacer (28) and outer spacer (27) in the proper orientation, as
shown.
Illustration 6 g01204931
8. Use Tooling (L) to measure the distance from the outer spacer to the surface of the table.
The distance should be 22.1 ± 0.6 mm (0.87 ± 0.02 inch). If this measurement is off, check
orientation of the washers. If orientation is correct, replace washers and spacers with new
parts.
4/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 7 g00625917
9. Install inner spacer (28), washers (25), and outer spacer (27) to barrel (24).
10. Install guide (26) to the barrel.
Illustration 8 g00625911
11. Install piston assemblies (23) with retainer (22) in the piston assembly's original bore in
barrel (24).
Illustration 9 g00625908
12. Install cam plate (21) on the rotating group.
5/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 10 g00666621
Illustration 11 g00628062
13. Use a suitable press to install bearing (19) onto shaft assembly (18).
Illustration 12 g00668076
14. Use a suitable press in order to install inner race (20) onto shaft assembly (18).
Note: Place the two support plates under the lip of shaft assembly (18).
6/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 13 g00626633
15. Insert shaft assembly (18) in the rotating group.
Illustration 14 g00625891
Illustration 15 g00666743
16. Alternate disks (17) and separator plates (16) into the travel motor housing. Start with a
separator plate and end with a separator plate.
7/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 16 g00626837
17. Attach Tooling (D) to the shaft. Use a suitable lifting device in order to place barrel
assembly into the travel motor body.
Note: Align the notches of the cam plate with the keys in the travel motor body before you
lower the barrel assembly into the travel motor body.
Illustration 17 g01204938
18. Use Tooling (M) to measure the depth from the top surface of the travel motor body to the
bronze face of the barrel assembly. The distance should be 32.2 ± 2 mm (1.27 ± 0.08 inch).
If this measurement is off, check orientation of the barrel assembly. Also check if the cam
plate is properly seated on the keys.
8/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 18 g00625888
Illustration 19 g00667938
(15) O-Ring seals
19. Install O-ring seals (15) and the backup rings on the brake piston.
Note: Make sure that you install the backup ring and the O-ring seal in the original position.
Refer to Illustration 19.
9/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 20 g00629015
20. Install brake piston (14) in the body of the travel motor by hand. It may be necessary to use
a soft faced hammer to seat the brake piston correctly.
Illustration 21 g01204953
21. Use Tooling (M) to measure the distance from the top of the brake piston (14) to the top
surface of the travel motor body. The distance should be 20.8 ± 1.0 mm (0.82 ± 0.04 inch).
If this measurement is off, drive the brake piston further into the travel motor body.
Illustration 22 g00627391
22. Install springs (12) and plate (11).
10/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Eng...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. 23. Install O-ring seals (13).
Illustration 23 g01204965
24. Use Tooling (G) to drive the bearing into the head.
Illustration 24 g00627405
25. Install O-ring seal (9) onto the head.
26. Install port plate (8) on the head. It may be necessary to apply a small amount of grease to
the port plate in order to hold the port plate in place during the installation of the head.
Illustration 25 g01205007
11/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Eng...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. 27. Turn over head (6). Install Tooling (A) onto the head. Use a suitable lifting device to install
the head onto the travel motor.
Illustration 26 g00631594
28. Install Pins (7) into the head.
Illustration 27 g00628657
29. Install an O-ring on each plug (5).
30. Install bolts (4) which hold the head in place. Tighten the six bolts to a torque of
530 ± 70 N·m (391 ± 52 lb ft).
31. Install plugs (5) that hold the pins in the head. Tighten the plugs to a torque of 75 ± 7 N·m
(55 ± 5 lb ft).
12/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Eng...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 28 g00624938
32. Install O-ring seals (2) and rings (3) on the displacement change valve.
Illustration 29 g00627438
33. Install displacement change valve (1) onto the head of the travel motor. Tighten the
displacement change valve to a torque of 50 ± 3 N·m (37 ± 2 lb ft).
34. To prevent possible damage to the travel motor, the unit should be filled with oil at least up
to the fill port prior to operation. Refer to Operation and Maintenance Manual for the
correct oil specification.
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 1 13:30:17 UTC+0800 2020
13/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Eng...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D EXCAVATOR GKF
Configuration: 349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile
Hydraulic Power Units Machine Systems
Media Number -RENR9574-10 Publication Date -01/08/2014 Date Updated -18/09/2018
i02429546
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Threaded Rod
M 20 X 2.5 by 18 inch
2
B 140-7742 Sleeve 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/2
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 1 g01213930
Illustration 2 g01213930
1. Install Tooling (A) as a guide. Attach Tooling (B) and a suitable lifting device onto travel
motor (4). The weight of travel motor assembly (4) is approximately 127 kg (280 lb).
Position travel motor assembly (4) and install bolts (3).
Illustration 3 g01213929
2. Install bolts (2). Connect hose assemblies (1).
End By:
a. Install the counterbalance valve. Refer to Disassembly and Assembly, "Counterbalance
Valve (Travel) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 1 13:31:13 UTC+0800 2020
2/2
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D EXCAVATOR GKF
Configuration: 349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile
Hydraulic Power Units Machine Systems
Media Number -RENR9574-10 Publication Date -01/08/2014 Date Updated -18/09/2018
i02429611
Final Drive and Travel Motor - Remove
SMCS - 4050-011; 4351-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A Block 1
B
1U-6221 Hydraulic Torque Wrench Assembly 1
132-8154 3/4 inch Square Drive Link 1
132-8223 Power Pack 1
C 138-7575 Link Bracket 2
Note: The final drive sprocket does not need to be removed prior to removal of the final drive.
The sprocket must be removed in order to disassemble the final drive.
Note: The procedure to remove the right hand final drive and the procedure to remove the left
hand final drive is identical. The procedure that follows is for one of the final drives.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Release track tension. Refer to Operation and Maintenance Manual, "Track Adjustment -
Adjust".
Illustration 1 g01213996
2. Start the machine and position track roller (1) on Tooling (A). Make sure that the pin for
separating the track is positioned over the final drive.
3. Separate the track. Refer to Disassembly and Assembly, "Track - Seperate".
4. Drain the final drive. Refer to Operation and Maintenance Manual, "Final Drive Oil -
Change".
5. Remove the counterbalance valve. Refer to Disassembly and Assembly, "Counterbalance
Valve - Remove and Install".
2/4
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 2 g01214021
6. Attach two lifting slings and a suitable lifting device to final drive (2), as shown. It may be
necessary to adjust the lifting straps for correct balance of the final drive.
Illustration 3 g01214049
Illustration 4 g01214023
3/4
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. 7. Disconnect hose assemblies (3). Remove fittings (4) and bolts (5).
8. Use Tooling (B) to remove bolts (5) and the washers that hold the final drive to the
undercarriage frame assembly. Carefully remove the final drive and the travel motor from
the undercarriage frame assembly. The combined weight of the final drive and the travel
motor is 725 kg (1600 lb).
Illustration 5 g01214002
9. Invert final drive assembly (6) onto the cover, as shown.
10. Attach Tooling (C) and a suitable lifting device in order to remove travel motor (6). The
weight of travel motor assembly (6) is approximately 127 kg (280 lb). Remove travel motor
assembly (6).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 1 13:32:09 UTC+0800 2020
4/4
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 349D EXCAVATOR GKF
Configuration: 349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile
Hydraulic Power Units Machine Systems
Media Number -RENR9574-10 Publication Date -01/08/2014 Date Updated -18/09/2018
i05331566
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Stand Group 1
B 138-7573 Link Bracket 2
C 1P-1860 Retaining Ring Pliers 1
D 4C-8359 Eyebolt 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive and Travel Motor
- Remove" in this manual.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
1/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 1 g01207795
2. Remove coupling (1) from final drive (2) .
3. Attach a suitable lifting device to the final drive, and turn final drive (2) over 180 degrees.
The weight of final drive (2) is approximately 590 kg (1300 lb).
Illustration 2 g01207796
4. Attach the final drive to Tooling (A) . Put an alignment mark across the sections of the final
drive for assembly purposes. All parts must be reinstalled in the original locations.
5. Remove socket head screws (3) from the final drive cover.
2/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 3 g01207801
6. Attach Tooling (B) and a suitable lifting device to cover (5) , as shown. The weight of cover
(5) is approximately 52 kg (115 lb).
7. Remove bolts (4) and the washers that hold the cover in place.
8. Use a soft faced hammer in order to break the seal between cover (5) and the ring gear.
Remove cover (5) . The weight of cover (5) is 52 kg (115 lb).
Illustration 4 g01207835
9. Remove spacer (6) from the cover.
3/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 5 g01207845
10. Remove shims (7) from the cover.
11. Remove socket head bolts (8) and ring gear (9) from the cover.
Illustration 6 g01207864
12. Remove sun gear (10) from carrier assembly (11) . Remove carrier assembly (11) by lifting
the carrier assembly straight up.
13. Disassemble carrier assembly (11) , as follows:
4/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 7 g01207865
a. Remove spacers (12) . A spacer is located on each side of the sun gear in carrier
assembly (11) .
Note: Planetary gears (15) might be stamped with identification marks "L". Note the
position of the identification marks in relation to the carrier for assembly purposes.
Illustration 8 g01207897
b. Remove retaining ring (13) with Tooling (C) .
c. Remove thrust washers (14) and planetary gear (15) from the carrier.
d. Remove bearing (16) from the planetary gear.
e. Repeat Steps 13.b through 13.d for the other two planetary gears.
Illustration 9 g01208035
f. Use a screwdriver in order to remove retaining ring (17) from the carrier. Remove sun
gear (18) from the carrier.
5/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 10 g01208136
14. Attach Tooling (D) and a suitable lifting device to carrier assembly (19) , as shown.
Remove carrier assembly (19) by pulling the carrier assembly straight up. The weight of
carrier assembly (19) is approximately 45 kg (100 lb).
15. Disassemble carrier assembly (19) , as follows:
Note: Spacer (20) may remain with carrier assembly (19) , or the spacer may remain with
carrier assembly (28) . Refer to Step 17.
Illustration 11 g01208162
a. Remove spacer (20) from carrier assembly (19) .
6/13
349D & 349D L Excavators GKF00001-UP (MACHINE) POWERED BY C13 Engine...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...