This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...fjjskqazxedmmem
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure describes taking off the electric starting motor, flywheel, rear gear components, covers and seals. The installation procedure outlines lowering the temperatures of bearings before inserting them and ensuring proper dimensions are met. Tools and torque specifications are listed for reassembling with loctite and checking flywheel runout.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...fjisejkdmd8id
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f8sejdkdmdijd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific instructions for installing seals and bearings. Tools and torque specifications are provided.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...yqen95561858
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...ze3xiandiao
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...fjjskqazxedmmem
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure describes taking off the electric starting motor, flywheel, rear gear components, covers and seals. The installation procedure outlines lowering the temperatures of bearings before inserting them and ensuring proper dimensions are met. Tools and torque specifications are listed for reassembling with loctite and checking flywheel runout.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...fjisejkdmd8id
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f8sejdkdmdijd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific instructions for installing seals and bearings. Tools and torque specifications are provided.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...yqen95561858
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...ze3xiandiao
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f7usuejkdkddm3
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...ufs89eodkdmdm
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkskmmdmd1
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkksmemmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other gears and covers. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...ifkkdkmdmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...jjfksekdmejik
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves removing multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel, which involves cleaning, applying sealant, heating components, and torquing bolts to the specified values. Precise alignment and positioning of gears and bearings is critical.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...fjjskqazxedmmem
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures to remove the rear crankshaft seal, gear group components like gears and covers, and installing new seals and bearings in their proper positions.
2. Detailed steps and illustrations are provided to remove and install the flywheel.
3. Removal of the crankshaft rear seal is outlined, noting inspection of the crankshaft seal surface afterwards. Precautions are included to contain fluids during disassembly.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...zatao0179249295
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
1. The rear gear group is removed by taking off bolts, seals, gears, and covers. Proper bearing installation is emphasized.
2. Flywheel removal requires lifting equipment due to its weight. Installation involves heating the ring gear, applying loctite, and torqueing bolts.
3. Removing the crankshaft rear seal involves taking off bolts. Inspection of the seal surface and crankshaft specifications is noted.
4. Installing the rear seal requires cleaning, applying primer and retaining compound, and following a tightening sequence.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...yinranhe0814
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator. The components include the rear gear group, flywheel, crankshaft rear seal. Detailed step-by-step procedures are provided along with illustrations. Required tools are listed for each job. Safety notices and other important information is also included.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...wfu089267
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
1. The rear gear group is removed by taking off bolts, seals, gears, and covers. Proper bearing installation is emphasized.
2. Flywheel removal requires lifting equipment due to its weight. Installation involves heating the ring gear, applying loctite, and torqueing bolts.
3. Removing the crankshaft rear seal involves taking off bolts. Inspection of the seal surface and crankshaft specifications is noted.
4. Installing the rear seal requires cleaning, applying primer and retaining compound, and following a tightening sequence.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...fjjskqazxedmmem
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing the rear gear group and rear crankshaft seal of a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 12 steps including cleaning parts, installing bearings, seals, gears, and bolts while ensuring proper dimensions and torque specifications are followed. Tools required are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...fjisejkdmd8id
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f8sejdkdmdijd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...ifkkdkmdmd
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying loctite to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...yqen95561858
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and multi-step procedures involving removing and installing various components like bolts, seals, gears, and bearings.
3. Precise instructions are given regarding tool usage, component orientation, and torque specifications to correctly disassemble and reassemble the rear of the engine.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual Instant D...fskekkdmdmdm3e
- The document provides instructions for removing and installing the idler gear of the front gear group on a C4.2 engine for Caterpillar built machines.
- To remove the idler gear, the front housing must first be removed. Then the idler gear bolt, thrust plate, and idler gear can be taken off the idler gear shaft. An idler shaft puller and driver group may be needed.
- To install the idler gear, first press in a new bushing if needed. Then install the idler shaft, idler gear, thrust plate, washer and idler gear bolt. Tighten the bolt to the specified torque.
More Related Content
Similar to Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant Download.pdf
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...f7usuejkdkddm3
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...ufs89eodkdmdm
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkskmmdmd1
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkksmemmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other gears and covers. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...ifkkdkmdmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...jjfksekdmejik
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves removing multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel, which involves cleaning, applying sealant, heating components, and torquing bolts to the specified values. Precise alignment and positioning of gears and bearings is critical.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...fjjskqazxedmmem
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures to remove the rear crankshaft seal, gear group components like gears and covers, and installing new seals and bearings in their proper positions.
2. Detailed steps and illustrations are provided to remove and install the flywheel.
3. Removal of the crankshaft rear seal is outlined, noting inspection of the crankshaft seal surface afterwards. Precautions are included to contain fluids during disassembly.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...zatao0179249295
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
1. The rear gear group is removed by taking off bolts, seals, gears, and covers. Proper bearing installation is emphasized.
2. Flywheel removal requires lifting equipment due to its weight. Installation involves heating the ring gear, applying loctite, and torqueing bolts.
3. Removing the crankshaft rear seal involves taking off bolts. Inspection of the seal surface and crankshaft specifications is noted.
4. Installing the rear seal requires cleaning, applying primer and retaining compound, and following a tightening sequence.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...yinranhe0814
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator. The components include the rear gear group, flywheel, crankshaft rear seal. Detailed step-by-step procedures are provided along with illustrations. Required tools are listed for each job. Safety notices and other important information is also included.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...wfu089267
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
1. The rear gear group is removed by taking off bolts, seals, gears, and covers. Proper bearing installation is emphasized.
2. Flywheel removal requires lifting equipment due to its weight. Installation involves heating the ring gear, applying loctite, and torqueing bolts.
3. Removing the crankshaft rear seal involves taking off bolts. Inspection of the seal surface and crankshaft specifications is noted.
4. Installing the rear seal requires cleaning, applying primer and retaining compound, and following a tightening sequence.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...fjjskqazxedmmem
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing the rear gear group and rear crankshaft seal of a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 12 steps including cleaning parts, installing bearings, seals, gears, and bolts while ensuring proper dimensions and torque specifications are followed. Tools required are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...fjisejkdmd8id
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f8sejdkdmdijd
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling and assembling these components.
3. Proper installation requires using specific tools to install components like bearings at the correct temperature and orientation.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...ifkkdkmdmd
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying loctite to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...yqen95561858
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and multi-step procedures involving removing and installing various components like bolts, seals, gears, and bearings.
3. Precise instructions are given regarding tool usage, component orientation, and torque specifications to correctly disassemble and reassemble the rear of the engine.
Similar to Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant Download.pdf (19)
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual Instant D...fskekkdmdmdm3e
- The document provides instructions for removing and installing the idler gear of the front gear group on a C4.2 engine for Caterpillar built machines.
- To remove the idler gear, the front housing must first be removed. Then the idler gear bolt, thrust plate, and idler gear can be taken off the idler gear shaft. An idler shaft puller and driver group may be needed.
- To install the idler gear, first press in a new bushing if needed. Then install the idler shaft, idler gear, thrust plate, washer and idler gear bolt. Tighten the bolt to the specified torque.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly process removes components like housing, gears, seals and bearings. The 22 step assembly process reverses this to rebuild the final drive, applying loctite and torquing bolts to specification. Tools required include link brackets, crossblocks, drivers and torque wrenches. Safety precautions are noted for releasing spring forces.
Caterpillar Cat 336F and 336F L Excavator (Prefix DSW) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs and seals. Tools required include a transmission repair stand, lifting eye assembly, driver group and various bolts, pins and seals. Technicians are advised to mark components for reinstallation and take care when removing parts to avoid damage.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 345D L Excavator (Prefix JKN) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, bearings and other components into the travel motor housing and barrel. Measurements are taken throughout to ensure proper assembly. The travel motor is then installed on the excavator and filled with the correct oil type.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor. It details 27 steps for assembling the travel motor that include installing seals, springs, pistons, and other components in the proper order and orientation. Thirteen steps are listed for disassembling the final drive, which include removing the cover, gears, and planetary gear assembly. Personal injury warnings are provided and all components must be cleaned before assembly.
Caterpillar Cat 336E L Excavator (Prefix BZY) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor of a 336E L excavator. The disassembly procedure involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstalling parts. Special care must be taken when handling springs or parts under spring force to avoid injury.
Caterpillar Cat 330F and 330F L Excavator (Prefix LCG) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. It describes 37 steps to disassemble the final drive by removing gears, shafts, housings, seals and other components. It then describes 34 steps to reassemble the final drive, including pressing in new bearings, installing seals, adjusting bearing preload with shims, and applying threadlocker to bolts. Precise tools and lifting devices are required due to the heavy weights of up to 550 kg involved.
Caterpillar Cat 336E L Excavator (Prefix DPX) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor on a 336E L excavator. The disassembly process involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on lubricating parts and ensuring proper alignment of components.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fskekkdmdmdm3e
1) The document provides step-by-step instructions for disassembling the travel motor of a 336D2L excavator.
2) It describes removing over 30 components of the travel motor including the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates and more.
3) Detailed illustrations are provided to accompany each step showing how to remove each component using the recommended tools.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It describes 13 steps to remove the component, which include disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. 11 steps are listed to install the component, in reverse order, including attaching lifting devices, positioning the assembly, and reinstalling hoses and covers. Tools and torque specifications are provided.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLC) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for removing and installing a crankshaft wear sleeve and crankshaft gear on a 325C excavator. It describes using various tools to distort and remove the existing wear sleeve and instructions for installing a new sleeve using a multi-piece installer tool. It also outlines steps for removing the crankshaft gear using a bearing puller and installing the gear by heating it and pressing it onto the crankshaft. The document provides maintenance technicians with detailed parts and tool information as well as safety notices for completing these tasks.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for assembling and installing a travel motor. It outlines 34 steps for assembling components like pistons, seals, plates, and bearings. It also describes using tools to measure clearances and distances during assembly. Finally, it details installing the assembled travel motor using lifting devices and bolts, and connecting hydraulic hose assemblies.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for removing and installing the rear gear group and rear crankshaft seal of a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 12 steps including cleaning parts, installing bearings, seals, gears, and bolts while ensuring proper dimensions and torque specifications are followed. Tools required include drivers, link brackets, guide studs, and installation tools.
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306B engine. It describes:
1) Marking the gears to ensure proper timing during removal and installation.
2) Removing the camshaft bolts and carefully removing the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before installation.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
The document provides instructions for removing and installing various components of a Caterpillar 621E wheel scraper, including:
1) Removing and installing the push-pull plate that connects the push-pull spring to the support assembly.
2) Disassembling and assembling the push-pull spring itself by removing discs and plates.
3) A detailed process for removing and installing the ejector cylinder, which requires the use of lifting tools and wood blocks due to the cylinder's weight.
4) Brief instructions for removing and adjusting the position of the lower front and guide rollers on the ejector assembly.
This document provides assembly instructions for a final drive on an excavator. It involves assembling and installing several components in the following order: installing bearings and determining shim thickness; installing seals; installing dowel pins; installing the housing on the motor housing; installing coupling gear, bolts, and ring gear; assembling carrier assemblies; installing gears, shafts, and retaining rings; installing the cover and testing for leaks. The process requires precision measurements and uses several specialized tools to properly assemble the final drive.
How To Fix The Key Not Detected Issue In Mercedes CarsIntegrity Motorcar
Experiencing a "Key Not Detected" problem in your Mercedes? Don’t take it for granted. Go through this presentation to find out the exact nature of the issue you are dealing with. Have your vehicle checked by a certified professional if necessary.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345D L EXCAVATOR YEE
Configuration: 345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06931709
Gear Group (Rear) - Remove and Install
SMCS - 1206-010; 1212-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp. 1
B 1P-0510 Driver Gp 1
Start By:
a. Remove the electric starting motor.
b. Remove the flywheel.
1. Support the engine.
1/10
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g06002548
2. Remove bolts (2) and rear crankshaft seal (1).
Illustration 2 g06002556
3. Remove bolts (4) and the washers. Remove cover (3) and the seal.
Illustration 3 g06002558
4. Remove gear (7), bolts (6), and gear (5).
Illustration 4 g06002564
2/10
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. 5. Remove O-ring seal (8) from gear (7).
Illustration 5 g06172622
6. Use Tooling (A) to remove bushing (7A) from gear assembly (7).
Illustration 6 g06172537
7. Remove bolts (9), adapter assembly (10), and the O-ring seal.
Illustration 7 g06172541
8. Use Tooling (B) to remove bearing (11) from adapter assembly (10).
3/10
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 8 g06172549
9. Remove gear assembly (12).
Illustration 9 g06172554
10. Remove cover (13) and the O-ring seal.
Illustration 10 g06172557
11. Use Tooling (B) to remove bearing (14).
Installation Procedure
4/10
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Table 2
Required Tools
Tool Part Number Part Description Qty
A 095-0706 Bolt 2
Illustration 11 g06172557
Illustration 12 g06172580
5/10
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 13 g06172587
1. Lower the temperature of bearing (14). Be sure to match Dimension (B) and Dimension (C)
when installing bearing (14.). Dimension (B) indicates the angle of the joint on bearing (14).
Dimension (B) is 15° ± 1°. Dimension (C) shows the distance from bearing (14) to the end
of the bore. Dimension (C) is 4.000 ± 0.500 mm (0.1575 ± 0.0197 inch).
Illustration 14 g06172554
2. Install the O-ring seal and cover (9).
6/10
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 15 g06172597
3. Install gear assembly (12) with oil passage plug (12A) facing out.
Illustration 16 g06172601
Illustration 17 g06172609
4. Lower the temperature of bearing (11). Be sure to match Dimension (F) and Dimension (G)
when installing bearing (11) into adapter assembly (10). Dimension (F) indicates the angle
of the joint on bearing (11). Dimension (F) is 15° ± 1°. Dimension (G) shows the distance
from bearing (11) to the end of the bore. Dimension (G) is 3.500 ± 0.500 mm
(0.1378 ± 0.0197 inch).
7/10
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 18 g06172537
5. Install the O-ring seal, adapter assembly (10), and bolts (9).
Illustration 19 g06172619
6. Lower the temperature of bearing (7A). Install bearing (7A) into gear assembly (7). Be sure
that each relief (H) is within 2° of each relief in gear assembly (7).
Illustration 20 g06002564
7. Install O-ring seal (8) onto gear (7).
8/10
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 21 g06002578
8. Install gear (5) and bolts (6).
Note: Tooling (A) is for supporting gear (7) during the installation of the cover and the rear
crankshaft seal.
Note: The bolt holes in gear (7) are not symmetrical. When installing Tooling (C), check
the rest of the bolts holes in gear (7) are aligned with the holes in the crankshaft.
9. Install gear (7) and Tooling (C).
Illustration 22 g06002581
10. Install cover (3), the seal, bolts (4), and the washers.
9/10
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 23 g06002592
11. Install rear crankshaft seal (1) and bolts (2).
12. Remove Tooling (C).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:46:46 UTC+0800 2020
10/10
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345D L EXCAVATOR YEE
Configuration: 345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249234
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B FT2712 Guide Stud 1
1/2
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 1 g01132214
1. Attach Tooling (A) and a suitable lifting device to flywheel (2). The weight of flywheel (2)
is approximately 79 kg (175 lb).
2. Remove top bolt (1). Install Tooling (B).
3. Remove remaining bolts (1).
4. Remove flywheel (2).
5. Use a hammer and a punch in order to remove the ring gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:47:43 UTC+0800 2020
2/2
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345D L EXCAVATOR YEE
Configuration: 345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06123534
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B FT2712 Guide Stud 1
C - Loctite 242 1
Always wear protective gloves when handling parts that have been
heated.
1. Raise the temperature of the ring gear. Position the ring gear with the part number toward
the crankshaft. Install the ring gear on the flywheel. Allow the ring gear to cool. Use a soft
hammer in order to seat the ring gear against the shoulder of the flywheel.
1/2
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 1 g01132214
2. Attach Tooling (A) and a suitable lifting device to flywheel (2) . The weight of flywheel (2)
is approximately 79 kg (175 lb).
3. Position flywheel (2) on Tooling (B) .
4. Apply Tooling (C) to bolts (1) .
5. Install bolts (1) . Remove Tooling (B) . Install remaining bolt (1) . Tighten the bolts evenly
to a torque of 300 ± 40 N·m (221 ± 30 lb ft).
6. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect" for the
correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:48:40 UTC+0800 2020
2/2
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345D L EXCAVATOR YEE
Configuration: 345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06010889
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 1 g01132235
1. Remove bolts (1).
2. Remove crankshaft rear seal (2).
Note: Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual Inspection and
Magnetic Particle Inspection" for the correct inspection procedure of the crankshaft seal surface.
Note: Refer to Reuse and Salvage Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9,
C-9, C10, C11, C12, C-12, C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the
correct specifications of the crankshaft.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:49:37 UTC+0800 2020
2/2
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345D L EXCAVATOR YEE
Configuration: 345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06010890
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 Primer N -
B - Loctite 620 Retaining Compound -
C 147-2675 Wear Sleeve Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 1 g01140085
Illustration 2 g03698745
Numerical tightening sequence for bolts (2).
Note: If required, install a crankshaft wear sleeve at engine overhaul. For more information
please refer to the following Reuse and Salvage Guidelines. Refer to Reuse and Salvage
Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9, C-9, C10, C11, C12, C-12,
2/3
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the correct specifications
of the crankshaft. Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual
Inspection and Magnetic Particle Inspection" for the correct inspection procedure of the
crankshaft seal surface.
1. If a crankshaft wear sleeve is necessary, refer to Step 1.a through Step 1.d to install the
crankshaft wear sleeve. If a crankshaft wear sleeve is not necessary, refer to Step 2.
a. Clean and polish the crankshaft of imperfections.
b. Use Tooling (A) to clean the outside diameter of the crankshaft and the inside
diameter of the crankshaft wear sleeve.
c. Apply Tooling (B) to the outside diameter of the crankshaft and the inside diameter of
the crankshaft wear sleeve.
d. Use Tooling (C) to install the crankshaft wear sleeve.
Note: Leave the shipping sleeve in place to install the crankshaft rear seal. The crankshaft
rear seal must be installed dry.
Note: If the seal group, O-ring seal, and the shipping sleeve are separated, these
components should not be used.
2. Lubricate the O-ring seal with clean engine oil that is on the back of the crankshaft rear seal
(1).
3. Position crankshaft rear seal (1) and the shipping sleeve over the crankshaft. Push
crankshaft rear seal (1) in place to dislodge the shipping sleeve.
Note: Do not remove the shipping sleeve until bolts (2) are installed.
4. Install new bolts (2) hand tight. Then, tighten bolts (2) in numerical sequence, shown in
Illustration 2. Tighten bolts (2) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:50:33 UTC+0800 2020
3/3
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345D L EXCAVATOR YEE
Configuration: 345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249340
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
1. Support the engine.
Illustration 1 g01132273
1/3
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. 2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2)
is approximately 62 kg (137 lb).
3. Remove bolts (1) and flywheel housing (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8846 Gasket Sealant 1
1. Apply Tooling (A) to the face of the cylinder block.
Illustration 2 g01132273
2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2)
is approximately 62 kg (137 lb). Position flywheel housing (2) on the rear of the cylinder
block.
3. Install bolts (1).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Mon Jul 6 09:51:30 UTC+0800 2020
2/3
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345D L EXCAVATOR YEE
Configuration: 345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249982
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
1/3
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 1 g01132580
1. Remove belt (1).
2. Attach a suitable lifting device to crankshaft vibration damper and pulley (3). The weight of
crankshaft vibration damper and pulley (3) is approximately 27 kg (60 lb). Remove bolts
(2).
3. Remove crankshaft vibration damper and pulley (3).
Installation Procedure
2/3
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 2 g01132580
1. Attach a suitable lifting device to crankshaft vibration damper and pulley (3). The weight of
crankshaft vibration damper and pulley (3) is approximately 27 kg (60 lb). Position
crankshaft vibration damper and pulley (3) on the engine.
2. Install bolts (2).
3. Install belt (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:52:27 UTC+0800 2020
3/3
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345D L EXCAVATOR YEE
Configuration: 345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02250084
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Start By:
a. Remove the crankshaft vibration damper and pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
28. Illustration 1 g01132620
1. Remove nuts (1).
2. Remove crankshaft front seal (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:53:24 UTC+0800 2020
2/2
345D L Excavator YEE00001-UP (MACHINE) POWERED BY C13 Engine(SEBP52...
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...