This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176 engine. The removal procedure involves disconnecting sensors, tubes, wiring harnesses, and fuel filters before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, tightening bolts in a specific sequence, and reconnecting all components in reverse order. Tools required include a strap wrench and various sizes of drills, taps, and inserts for repairing damaged bolt threads if needed.
Caterpillar cat 345 b series ii excavator (prefix ccc) service repair manual ...kmf9ioseodk
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure includes disconnecting sensors and tubes, removing bolts, and lifting the cylinder head off using a strap wrench. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and lifting the cylinder head into place using a suitable device.
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual I...yan77xunhao
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and using guide bolts to position the cylinder head before reconnecting components.
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual (...f8usiejdkmdd
The document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176C engine. To remove the cylinder head, various components must first be disconnected including sensors, tubes, wiring harness, and fuel filter. The head bolts are then removed and the cylinder head lifted off using a suitable lifting device. To install the cylinder head, the mating surfaces are cleaned and the correct cylinder head gasket and O-rings are installed on the cylinder block before lowering the cylinder head into place.
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual (...dujdkksdmm
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and using guide bolts to position the cylinder head before reconnecting components.
Caterpillar cat 345 b series ii excavator (prefix ccc) service repair manual ...fujsekfkksemm
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds. The cylinder head bolts are then removed and the head lifted off using a suitable lifting device. For installation, the mating surfaces are cleaned and new gaskets installed before positioning the cylinder head on the block and installing the bolts.
Caterpillar cat 345 b series ii excavator (prefix ccc) service repair manual ...fjsekdmmeed
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176C engine. The removal process involves disconnecting various sensors and tubes, removing bolts, and lifting the cylinder head off. The installation involves cleaning surfaces, installing new gaskets and seals, lifting the cylinder head into place, and torquing the head bolts to the specified sequence and values. Proper cleaning, lubrication, and torque procedures are emphasized to ensure correct installation.
Caterpillar cat 345 b track type excavator (prefix 5ws) service repair manual...f8isoeidkdk
The document provides instructions for removing and installing cylinder head components on a Caterpillar 3176C engine, including:
1) Removal steps such as removing sensors, tubes, bolts and the cylinder head using a lifting device.
2) Installation steps such as cleaning surfaces, installing new gaskets and O-rings, lifting the cylinder head into place using a device, and torquing bolts to the specified value.
3) References other documents for removing related parts like the valve mechanism cover beforehand.
Caterpillar cat 345 bl track type excavator (prefix 5ws) service repair manua...jfdskekdmme
The document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves disconnecting sensors, tubes, hoses, and wiring before removing bolts and lifting the cylinder head off. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, tightening bolts in a specific sequence, and reconnecting all components in reverse order. Special tools are required and technicians should keep parts clean to prevent damage.
Caterpillar cat 345 b series ii excavator (prefix ccc) service repair manual ...kmf9ioseodk
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure includes disconnecting sensors and tubes, removing bolts, and lifting the cylinder head off using a strap wrench. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and lifting the cylinder head into place using a suitable device.
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual I...yan77xunhao
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and using guide bolts to position the cylinder head before reconnecting components.
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual (...f8usiejdkmdd
The document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176C engine. To remove the cylinder head, various components must first be disconnected including sensors, tubes, wiring harness, and fuel filter. The head bolts are then removed and the cylinder head lifted off using a suitable lifting device. To install the cylinder head, the mating surfaces are cleaned and the correct cylinder head gasket and O-rings are installed on the cylinder block before lowering the cylinder head into place.
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual (...dujdkksdmm
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and using guide bolts to position the cylinder head before reconnecting components.
Caterpillar cat 345 b series ii excavator (prefix ccc) service repair manual ...fujsekfkksemm
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds. The cylinder head bolts are then removed and the head lifted off using a suitable lifting device. For installation, the mating surfaces are cleaned and new gaskets installed before positioning the cylinder head on the block and installing the bolts.
Caterpillar cat 345 b series ii excavator (prefix ccc) service repair manual ...fjsekdmmeed
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176C engine. The removal process involves disconnecting various sensors and tubes, removing bolts, and lifting the cylinder head off. The installation involves cleaning surfaces, installing new gaskets and seals, lifting the cylinder head into place, and torquing the head bolts to the specified sequence and values. Proper cleaning, lubrication, and torque procedures are emphasized to ensure correct installation.
Caterpillar cat 345 b track type excavator (prefix 5ws) service repair manual...f8isoeidkdk
The document provides instructions for removing and installing cylinder head components on a Caterpillar 3176C engine, including:
1) Removal steps such as removing sensors, tubes, bolts and the cylinder head using a lifting device.
2) Installation steps such as cleaning surfaces, installing new gaskets and O-rings, lifting the cylinder head into place using a device, and torquing bolts to the specified value.
3) References other documents for removing related parts like the valve mechanism cover beforehand.
Caterpillar cat 345 bl track type excavator (prefix 5ws) service repair manua...jfdskekdmme
The document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves disconnecting sensors, tubes, hoses, and wiring before removing bolts and lifting the cylinder head off. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, tightening bolts in a specific sequence, and reconnecting all components in reverse order. Special tools are required and technicians should keep parts clean to prevent damage.
Caterpillar cat 345 b track type excavator (prefix 5ws) service repair manual...jfdskekdmme
The document provides instructions for removing and installing cylinder head components on a Caterpillar 3176C engine, including:
1) Removal steps such as removing sensors, tubes, bolts and the cylinder head using a lifting device.
2) Installation steps such as cleaning surfaces, installing new gaskets and O-rings, installing the cylinder head using a lifting device, and torquing bolts to the specified value.
3) The document provides illustrations of the components and tools needed to correctly perform the removal and installation.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 345B excavator engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean surfaces, inspect for damage, and install new gaskets and seals. Specific tightening procedures are outlined for installing the cylinder head and bolts to the correct torques.
Caterpillar cat 345 b excavator (prefix 6xs) service repair manual (6xs00001 ...f8isoeidkdk
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent contamination.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. The head bolts are tightened in a specific sequence to torques of 160 Nm initially and 90 degree turns, with some bolts at lower torque. Reinstalled components include water outlets, sensors, and hoses.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
Caterpillar Cat 390F L Excavator (Prefix FEH) Service Repair Manual (FEH00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the travel motor on a 390F excavator model. It involves 40 steps to disassemble the various components of the travel motor including removing seals, springs, plates, pistons, and bearings. The assembly section outlines 31 steps to reinstall these components in reverse order while ensuring proper cleaning and alignment of parts. Precision tools are required and safety precautions mentioned to avoid injury from spring forces.
Caterpillar Cat 374D L Excavator (Prefix PJA) Service Repair Manual (PJA00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the final drive of a 374D L Excavator. It describes 34 steps to disassemble the final drive by removing components like the ring gear, carrier assemblies, gears, shafts and seals. It then describes 8 steps for assembling the final drive, which involves cleaning parts, pressing in bearings and pins, installing housings and determining the correct shim number based on bearing preload measurements. The document contains detailed illustrations and lists required tools for each step.
Este documento contiene instrucciones para operar y mantener una máquina. Explica los números de la máquina, las señales de seguridad, cómo subirse y bajarse de la máquina, cómo operar la estación del operador, cómo conducir y operar la máquina, cómo transportarla, el mantenimiento requerido y las especificaciones técnicas.
Caterpillar Cat 374F L Excavator (Prefix DNM) Service Repair Manual (DNM00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. It lists the required tools and presents a step-by-step process to remove and install over 35 individual parts. Key steps include removing the ring gear, carrier assemblies, gears and shafts, and separating the main housing from the motor housing. Proper cleaning and application of sealant is emphasized throughout reassembly.
The document provides instructions for disassembling and assembling the travel motor of a 345C L EXCAVATOR. It lists 31 steps to disassemble the various components of the travel motor using different tools. These components include the head, plates, seals, pins, brake piston, disks, rotating group, shaft assembly, barrels, seals, and more. It emphasizes cleaning parts and marking components to ensure proper reassembly.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix GPH) Service Repair Manual...f8usiejdkmdd
This document provides instructions for disassembling and assembling the travel motor of a 345C L Hydraulic Excavator. The disassembly procedure involves 31 steps to remove components like the head, plates, disks, rotating group, seals and more. The assembly procedure involves 13 steps and notes to clean parts, apply lubricant, set proper measurements and orientations when reinstalling components like the washers, spacers and seals. Special tools are listed for tasks like removing bearings and installing seals.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists 31 steps to disassemble parts like the head, plates, seals, pistons, and housing. It then lists 27 steps to reassemble these parts in reverse order, making sure to clean parts and apply lubricant. Proper installation of seals, washers, and keys is emphasized.
This document provides instructions for disassembling and assembling the swing drive of a 340F Excavator. The disassembly procedure involves removing 27 parts from the swing drive including the cover, sun gear, carrier assembly, planetary gears, ring gear, pinion shaft, and bearings. The assembly procedure instructs installing lip seals and bearings on the cage and pinion shaft before lowering the cage over the pinion shaft and installing the bearing.
This document provides instructions for removing and installing an exhaust manifold and inlet and exhaust valves on a 325-A FM L EXCAVATOR 7LM. It describes:
1) Removing the bolts, exhaust manifold, and gaskets from the cylinder head to remove the exhaust manifold.
2) Installing new gaskets and mounting the exhaust manifold to the cylinder head, applying anti-seize compound and torqueing bolts.
3) Removing inlet and exhaust valves by compressing springs, removing retainers and springs, and removing seals and valves.
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 345 b track type excavator (prefix 5ws) service repair manual...jfdskekdmme
The document provides instructions for removing and installing cylinder head components on a Caterpillar 3176C engine, including:
1) Removal steps such as removing sensors, tubes, bolts and the cylinder head using a lifting device.
2) Installation steps such as cleaning surfaces, installing new gaskets and O-rings, installing the cylinder head using a lifting device, and torquing bolts to the specified value.
3) The document provides illustrations of the components and tools needed to correctly perform the removal and installation.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 345B excavator engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean surfaces, inspect for damage, and install new gaskets and seals. Specific tightening procedures are outlined for installing the cylinder head and bolts to the correct torques.
Caterpillar cat 345 b excavator (prefix 6xs) service repair manual (6xs00001 ...f8isoeidkdk
This document provides instructions for removing and installing cylinder heads on a Caterpillar 3176C engine. The removal procedure involves removing various components like sensors, tubes, and manifolds to access the cylinder head. Thirteen steps are outlined to remove the cylinder head, which weighs 135 kg. The installation procedure involves cleaning surfaces, inspecting for damage, selecting the correct gasket, and torquing 26 bolts to secure the cylinder head. Proper cleaning and installation of gaskets and seals is emphasized to prevent contamination.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. The head bolts are tightened in a specific sequence to torques of 160 Nm initially and 90 degree turns, with some bolts at lower torque. Reinstalled components include water outlets, sensors, and hoses.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces, select the correct gasket, and install the head using a lifting device. Detailed steps are given for tightening the head bolts in a specific sequence and torque pattern to properly secure the cylinder head.
Similar to Caterpillar Cat 345B Series II Excavator (Prefix DCW) Service Repair Manual (DCW00001 and up).pdf (9)
Caterpillar Cat 390F L Excavator (Prefix FEH) Service Repair Manual (FEH00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the travel motor on a 390F excavator model. It involves 40 steps to disassemble the various components of the travel motor including removing seals, springs, plates, pistons, and bearings. The assembly section outlines 31 steps to reinstall these components in reverse order while ensuring proper cleaning and alignment of parts. Precision tools are required and safety precautions mentioned to avoid injury from spring forces.
Caterpillar Cat 374D L Excavator (Prefix PJA) Service Repair Manual (PJA00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the final drive of a 374D L Excavator. It describes 34 steps to disassemble the final drive by removing components like the ring gear, carrier assemblies, gears, shafts and seals. It then describes 8 steps for assembling the final drive, which involves cleaning parts, pressing in bearings and pins, installing housings and determining the correct shim number based on bearing preload measurements. The document contains detailed illustrations and lists required tools for each step.
Este documento contiene instrucciones para operar y mantener una máquina. Explica los números de la máquina, las señales de seguridad, cómo subirse y bajarse de la máquina, cómo operar la estación del operador, cómo conducir y operar la máquina, cómo transportarla, el mantenimiento requerido y las especificaciones técnicas.
Caterpillar Cat 374F L Excavator (Prefix DNM) Service Repair Manual (DNM00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the final drive on a 374F L Excavator. It lists the required tools and presents a step-by-step process to remove and install over 35 individual parts. Key steps include removing the ring gear, carrier assemblies, gears and shafts, and separating the main housing from the motor housing. Proper cleaning and application of sealant is emphasized throughout reassembly.
The document provides instructions for disassembling and assembling the travel motor of a 345C L EXCAVATOR. It lists 31 steps to disassemble the various components of the travel motor using different tools. These components include the head, plates, seals, pins, brake piston, disks, rotating group, shaft assembly, barrels, seals, and more. It emphasizes cleaning parts and marking components to ensure proper reassembly.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix GPH) Service Repair Manual...f8usiejdkmdd
This document provides instructions for disassembling and assembling the travel motor of a 345C L Hydraulic Excavator. The disassembly procedure involves 31 steps to remove components like the head, plates, disks, rotating group, seals and more. The assembly procedure involves 13 steps and notes to clean parts, apply lubricant, set proper measurements and orientations when reinstalling components like the washers, spacers and seals. Special tools are listed for tasks like removing bearings and installing seals.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists 31 steps to disassemble parts like the head, plates, seals, pistons, and housing. It then lists 27 steps to reassemble these parts in reverse order, making sure to clean parts and apply lubricant. Proper installation of seals, washers, and keys is emphasized.
This document provides instructions for disassembling and assembling the swing drive of a 340F Excavator. The disassembly procedure involves removing 27 parts from the swing drive including the cover, sun gear, carrier assembly, planetary gears, ring gear, pinion shaft, and bearings. The assembly procedure instructs installing lip seals and bearings on the cage and pinion shaft before lowering the cage over the pinion shaft and installing the bearing.
This document provides instructions for removing and installing an exhaust manifold and inlet and exhaust valves on a 325-A FM L EXCAVATOR 7LM. It describes:
1) Removing the bolts, exhaust manifold, and gaskets from the cylinder head to remove the exhaust manifold.
2) Installing new gaskets and mounting the exhaust manifold to the cylinder head, applying anti-seize compound and torqueing bolts.
3) Removing inlet and exhaust valves by compressing springs, removing retainers and springs, and removing seals and valves.
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar Cat 385C L Excavator (Prefix T2E) Service Repair Manual (T2E00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. The disassembly process involves removing over 30 individual parts in a specific sequence. The assembly process reverses the disassembly steps and provides additional details on cleaning, lubricating, and setting bearing preloads using shims. Proper tools and lifting devices are required due to the large size and weight of many components. Cleanliness is emphasized throughout to prevent damage to precision parts from contaminants.
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure details cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash. Proper removal and installation is important to avoid engine damage.
This document provides instructions for disassembling and assembling the travel motor on a 390F excavator model. It involves over 40 steps to fully disassemble the travel motor by removing components like the head, relief valves, pistons, plates, seals, bearings, and housing. Special tools are required and safety precautions must be followed when removing spring-loaded or heavy parts. The assembly process reverses the disassembly steps and requires cleaning and lubricating parts before reinstallation.
Caterpillar Cat 385C L Excavator (Prefix EDA) Service Repair Manual (EDA00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and parts. The disassembly process involves removing over 30 components from the final drive housing in a specific sequence, including carrier assemblies, sun gears, planetary gear sets, and seals. The assembly process reverses the disassembly steps and provides notes on cleaning, inspecting, lubricating, and installing replacement parts as needed.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B II EXCAVATOR DCW
Configuration: 345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine
Disassembly and Assembly
3176C and 3196 Engines for Caterpillar Built Machines
Media Number -RENR1223-15 Publication Date -01/08/2015 Date Updated -03/08/2015
i01604601
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00515542
1. Place an identification mark on each rocker arm in order to identify the proper location in
the engine for installation.
2. Remove bolts (1) and rocker arms (2) .
3. Remove push rods (3). Keep each push rod with the respective rocker arm.
Illustration 2 g00515374
4. Remove valve bridges (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 19 00:15:25 UTC+0800 2020
2/2
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B II EXCAVATOR DCW
Configuration: 345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine
Disassembly and Assembly
3176C and 3196 Engines for Caterpillar Built Machines
Media Number -RENR1223-15 Publication Date -01/08/2015 Date Updated -03/08/2015
i07141366
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Inspect the condition of the following items: rocker arms, valve bridges, and push rods.
Replace the parts, if necessary.
Illustration 1 g00515542
2. Install push rods (3) in the correct location in the engine.
1/2
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 2 g00515374
3. Install valve bridges (4). Lubricate the top surface of the valve bridges with clean engine oil.
4. Place rocker arms (2) in the correct locations that were marked during removal. Install bolts
(1) and tighten to a torque of 100 ± 20 N·m (74 ± 15 lb ft).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 19 00:16:22 UTC+0800 2020
2/2
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B II EXCAVATOR DCW
Configuration: 345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine
Disassembly and Assembly
3176C and 3196 Engines for Caterpillar Built Machines
Media Number -RENR1223-15 Publication Date -01/08/2015 Date Updated -03/08/2015
i01771996
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
Start By:
A. Remove the base for the valve mechanism cover. Refer to Disassembly and Assembly,
"Valve Mechanism Cover Base - Remove and Install".
B. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00517348
1. Remove bolt (1). Remove clip (2) .
2. Disconnect sensors from engine wiring harness (3) .
3. Remove the sensors.
Illustration 2 g00517351
4. Remove bolts (5). Disconnect tube assembly (4) and remove the O-ring seal.
5. Remove bolts (7). Disconnect tube assembly (6) and remove the O-ring seals.
2/5
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g00517354
Typical example
6. Use Tooling (A) in order to remove fuel filter (8). Disconnect hose (9). Plug all openings
immediately.
7. Loosen bolt (11). Disconnect wiring harness (10) .
Illustration 4 g00517355
Typical example
8. Disconnect sensor connector (13) and clips (12). Remove clip (14) and the bolt.
3/5
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 5 g00517356
Typical example
9. Remove bolts (15) .
10. Remove water outlet manifold (16) .
Illustration 6 g00517359
11. Remove head bolts (17) .
12. Remove water outlet manifold gaskets (18) from cylinder head (19) .
4/5
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 7 g00517361
13. Attach a suitable lifting device to cylinder head (19). Remove cylinder head (19) from the
cylinder block. The weight of cylinder head (19) is 135 kg (300 lb).
14. Remove cylinder head gasket (20) and O-ring seals (21) from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 19 00:17:19 UTC+0800 2020
5/5
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B II EXCAVATOR DCW
Configuration: 345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine
Disassembly and Assembly
3176C and 3196 Engines for Caterpillar Built Machines
Media Number -RENR1223-15 Publication Date -01/08/2015 Date Updated -03/08/2015
i01792874
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
B 1U-5686 (1)
21/32 inch Drill Bit 1
C 4C-9732 (1)
M16x2.0-D7 Plug Tap 1
D 9U-5604 M16x2.0 32mm Heli-Coil Insert (2)
1
E 8T-2799 (1)
Heli-Coil Installation Tool 1
F 8T-3096 Plug Tap 1
G 6V-4876 Lubricant 1
( 1 )
Part of 4C-8367 Thread Repair Kit
( 2 )
This is a special length.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For more information, refer to Video Tape, LEVN5101, "C-10 and C-12 Head Gasket Repair
Procedure".
1. Thoroughly clean the mating surfaces of the cylinder head and the cylinder block.
1/7
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 2. Clean all 26 head bolt holes on the cylinder block with Tooling (F) .
3. After cleaning the threads, remove any debris from the head bolt holes on the cylinder block with a
vacuum line.
4. Visually inspect the head bolt holes on the cylinder block for thread damage.
5. If a damaged head bolt thread is observed, repair the damaged head bolt thread with a Heli-Coil
thread repair kit.
6. Inspect the cylinder head and the cylinder block for flatness. Refer to Guideline for Reusable Parts
and Salvage Operations, SEBF8162, "Procedure to Measure and Salvage Cylinder Head Assemblies
and Related Components".
Illustration 1 g00810396
Cylinder Head Gasket
(29) Straight Edge
2/7
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 2 g00810399
Cylinder Head Gasket
(28) Scalloped Edge
7. Determine the correct cylinder head gasket to use. Refer to Illustration 1 and Illustration 2.
Illustration 3 g00525775
8. Install the correct cylinder head gasket (26) and new O-ring seals (27) on the cylinder block. Inspect
the condition of the remaining gaskets. Replace the gaskets, if necessary.
Note: To avoid damage to the cylinder head gasket, use guide bolts of an appropriate size to install
the cylinder head.
9. Use a suitable lifting device to install the cylinder head on the cylinder block.
3/7
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 4 g00525534
10. Install four gaskets (24) on cylinder head (25) .
11. Install new cylinder head bolts (23). If the engine is equipped with a compression brake, then also
install new head bolt studs.
12. Lubricate the following components with Tooling (G) : the bolt threads, the underside of the bolt
heads and the washers. Follow Step 13 for the correct tightening procedure.
Illustration 5 g00517501
Note: Engines that are equipped with a compression brake will have three head bolt studs. Install the
head bolt studs in positions (2), (8), and (10). Tighten the head bolt studs in sequence with the
cylinder head bolts.
13. Tighten the cylinder head bolts according to the following procedure:
a. Tighten bolt (1) through bolt (26) in a numerical sequence to a torque of 160 ± 15 N·m (120 ±
11 lb ft).
b. Tighten bolt (1) through bolt (26) again in a numerical sequence to a torque of 160 ± 15 N·m
(120 ± 11 lb ft).
c. Place an index mark on each bolt head. Turn bolt (1) through bolt (26) in a numerical sequence
for an additional 90 degrees (1/4 turn).
4/7
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. d. Loosen bolt (1) through bolt (26) until the washers are loose under the bolt heads.
e. Tighten bolt (1) through bolt (26) in a numerical sequence to a torque of 160 ± 15 N·m (120 ±
11 lb ft).
f. Tighten bolt (1) through bolt (26) again in a numerical sequence to a torque of 160 ± 15 N·m
(120 ± 11 lb ft).
g. Place an index mark on each bolt head. Turn bolt (1) through bolt (26) in a numerical sequence
for an additional 90 degrees (1/4 turn).
h. Tighten bolt (27) through bolt (33) in a numerical sequence to a torque of 28 ± 7 N·m (20 ± 5
lb ft).
Illustration 6 g00525468
14. Install head bolt spacers (22) on the three head bolt studs. Tighten head bolt spacers (22) to a torque
of 100 ± 20 N·m (75 ± 15 lb ft).
15. Install water outlet manifold (21) and bolts (20) .
Illustration 7 g00814600
16. Hold line (19) in position and connect fittings (17). Install bolts (18) .
5/7
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 8 g00676967
17. Connect wiring harness (14). Tighten bolt (16) to a torque of 6 ± 1 N·m (53 ± 9 lb in).
18. Connect hose (15) .
Illustration 9 g00676971
19. Connect sensor connector (12). Install the clip, the washer, and bolt (11). Secure the wiring harness
with tie straps (13) .
20. Install fuel filter (10) with Tool (A). Follow the instructions on the fuel filter.
21. Connect hose (9) .
22. Install hose (8) .
23. Install the bolts, the washers, and two nuts (7) .
6/7
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 10 g00525386
24. Install tube assembly (5) with the O-ring seals, two bolts (6), and the washers.
25. Install tube assembly (3) with the O-ring seal, two bolts (4), and the washers. Install the clip and the
bolt to tube assembly (5) and (3) .
Illustration 11 g00524436
26. Route wiring harness (1) accordingly and connect sensor connector (2) .
27. Fill the cooling system with coolant to the correct level. Refer to the Operation and Maintenance
Manual for the correct filling procedure.
End By:
a. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrods - Install".
b. Install the valve cover base. Refer to Disassembly and Assembly, "Valve Mechanism Cover Base -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 19 00:18:15 UTC+0800 2020
7/7
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B II EXCAVATOR DCW
Configuration: 345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine
Disassembly and Assembly
3176C and 3196 Engines for Caterpillar Built Machines
Media Number -RENR1223-15 Publication Date -01/08/2015 Date Updated -03/08/2015
i02087499
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/5
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g01022184
1. Remove bolts (1) and lifter assembly (2). The lifter assembly can be removed in two
sections.
Illustration 2 g01022187
2/5
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 2. Remove the following items from the right end of lifter shaft (5) : bracket assembly (6),
valve lifters (8) and unit injector lifter (9) .
3. Remove the following items from the middle of lifter shaft (5) : valve lifters (8) and unit
injector lifter (9) .
4. Remove the following items from the left end of lifter shaft (5) : bracket assembly (7), valve
lifters (8) and unit injector lifter (9) .
5. Remove dowel (4) and cap plug (3) from lifter shaft (5) .
6. Remove the spring pin from bracket assembly (7), if necessary.
7. Remove dowel (10) from bracket assembly (6), if necessary.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g01022187
1. Install the spring pin and dowel (10) in bracket assembly (6). Install the spring pin and the
dowel in bracket assembly (7) .
2. Install dowel (4) and cap plug (3) in lifter shaft (5). Lubricate the lifter shaft with clean
engine oil prior to assembly.
3. Install the following items on the left end of lifter shaft (5) : bracket assembly (7), valve
lifters (8) and unit injector lifter (9) .
4. Install the following items on the middle of lifter shaft (5) : valve lifters (8) and unit injector
lifter (9) .
5. Install the following items on the right end of lifter shaft (5) : bracket assembly (6), valve
lifters (8) and unit injector lifter (9) .
4/5
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 4 g01022184
Note: Immerse the entire lifter assembly in clean engine oil prior to installation on the
engine.
6. Place the lifter assembly (2) on the engine and install bolts (1). Tighten the bolts to a torque
of 30 ± 3 N·m (22 ± 2 lb ft).
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 19 00:19:12 UTC+0800 2020
5/5
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B II EXCAVATOR DCW
Configuration: 345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine
Disassembly and Assembly
3176C and 3196 Engines for Caterpillar Built Machines
Media Number -RENR1223-15 Publication Date -01/08/2015 Date Updated -03/08/2015
i02363444
Camshaft - Remove
SMCS - 1210-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 131-1525 Camshaft Pilot 1
Start By:
A. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrod - Remove".
B. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
C. Remove the camshaft position sensor. Refer to Disassembly and Assembly, "Camshaft
Position Sensor - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
1/3
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. Install the timing
bolt in the flywheel. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1
Piston".
2. Ensure that the timing marks on the following gears are aligned: the camshaft drive gear, the
idler gear and the crankshaft gear.
Illustration 1 g00529917
Note: It is not necessary to remove the cylinder head for removal of the camshaft.
3. Wire the valve lifters away from the camshaft. See Illustration 1.
2/3
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 2 g00813405
4. Remove thrust pin (1) .
5. Install Tooling (A) into camshaft (2) .
Note: Lubricate Tooling (A) for easier removal of the camshaft. Lubrication also prevents
damaging the camshaft lobes and the camshaft bearings.
6. Carefully remove camshaft (2) from the engine.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 19 00:20:09 UTC+0800 2020
3/3
345B Series II Excavator DCW00001-UP (MACHINE) POWERED BY 3176 Engine(...
2020/9/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...