This document provides instructions for assembling the swing drive of a 345B II excavator. Key steps include:
1. Cleaning and inspecting all parts before assembly.
2. Applying anti-seize compound and grease to bearings and installing them into the swing drive housing along with the pinion shaft and bearing cage.
3. Heating and pressing the bearings into place using a press and driver group tool.
4. Temporarily installing bolts to hold the bearing cage aligned with the swing drive housing.
Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual (FEE0000...zatao0179249295
This document provides instructions for disassembling and assembling the swing drive of a 345B II Excavator. It lists required tools and begins by having the user remove the swing drive. Detailed steps are provided to disassemble the various components of the swing drive including removing retaining rings, planetary gears, and bearings. Reassembly follows the reverse order, with notes to clean parts thoroughly and apply specified compounds before reinstalling components. Proper lifting techniques and cleanliness are emphasized throughout.
Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual (FEE0000...luanxianshi27
This document provides instructions for disassembling and assembling the swing drive of a 345B II Excavator. It lists required tools and begins by having the user remove the swing drive. Detailed steps are provided to disassemble the various components of the swing drive including removing retaining rings, planetary gears, and bearings. Reassembly follows the reverse order, with notes to clean parts thoroughly and apply specified compounds before reinstalling components. Proper lifting techniques and cleanliness are emphasized throughout.
Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual (FEE0000...wfu089267
The document provides instructions for assembling the swing drive of a 345B II excavator. Key steps include:
1. Cleaning and inspecting all parts before assembly.
2. Applying anti-seize compound and installing bearings and seals in the proper order.
3. Heating and pressing bearings onto the pinion shaft and into the swing drive housing.
The assembly procedure involves correctly installing over 30 parts in the swing drive in the specified sequence. Proper cleaning and application of compounds is important to ensure correct assembly.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...uddksemd8ud
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...f7djidksmd3e
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...paws21610697
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. It describes:
1) Disassembling the various components of the final drive by removing bolts, pins, gears, and other parts.
2) Proper cleaning and preparation of parts before assembly.
3) The assembly procedure, including installing seals, bearings, gears and other components in the correct order and orientation. Precise measurements are taken to determine the proper shim thickness.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. It describes:
1) Disassembling the various components of the final drive by removing bolts, pins, gears, and other parts.
2) Properly supporting components with tooling as they are removed to avoid injury.
3) Cleaning all parts thoroughly before assembly.
4) Assembling the components in reverse order, applying anti-seize compound, torqueing bolts, and ensuring proper bearing preload using shims.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...jdjkskmikdkmd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and verifying seal installation. Proper cleaning and torqueing of fasteners is emphasized.
Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual (FEE0000...zatao0179249295
This document provides instructions for disassembling and assembling the swing drive of a 345B II Excavator. It lists required tools and begins by having the user remove the swing drive. Detailed steps are provided to disassemble the various components of the swing drive including removing retaining rings, planetary gears, and bearings. Reassembly follows the reverse order, with notes to clean parts thoroughly and apply specified compounds before reinstalling components. Proper lifting techniques and cleanliness are emphasized throughout.
Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual (FEE0000...luanxianshi27
This document provides instructions for disassembling and assembling the swing drive of a 345B II Excavator. It lists required tools and begins by having the user remove the swing drive. Detailed steps are provided to disassemble the various components of the swing drive including removing retaining rings, planetary gears, and bearings. Reassembly follows the reverse order, with notes to clean parts thoroughly and apply specified compounds before reinstalling components. Proper lifting techniques and cleanliness are emphasized throughout.
Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual (FEE0000...wfu089267
The document provides instructions for assembling the swing drive of a 345B II excavator. Key steps include:
1. Cleaning and inspecting all parts before assembly.
2. Applying anti-seize compound and installing bearings and seals in the proper order.
3. Heating and pressing bearings onto the pinion shaft and into the swing drive housing.
The assembly procedure involves correctly installing over 30 parts in the swing drive in the specified sequence. Proper cleaning and application of compounds is important to ensure correct assembly.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...uddksemd8ud
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...f7djidksmd3e
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...paws21610697
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. It describes:
1) Disassembling the various components of the final drive by removing bolts, pins, gears, and other parts.
2) Proper cleaning and preparation of parts before assembly.
3) The assembly procedure, including installing seals, bearings, gears and other components in the correct order and orientation. Precise measurements are taken to determine the proper shim thickness.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. It describes:
1) Disassembling the various components of the final drive by removing bolts, pins, gears, and other parts.
2) Properly supporting components with tooling as they are removed to avoid injury.
3) Cleaning all parts thoroughly before assembly.
4) Assembling the components in reverse order, applying anti-seize compound, torqueing bolts, and ensuring proper bearing preload using shims.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual (DER0000...jdjkskmikdkmd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and verifying seal installation. Proper cleaning and torqueing of fasteners is emphasized.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual Instant ...jiuliu14811471
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and verifying seal installation. Proper cleaning and torqueing of fasteners is emphasized.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual Instant ...qianxu35543635
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. It describes:
1) Disassembling the various components of the final drive by removing bolts, pins, gears, and other parts.
2) Properly supporting components with tooling as they are removed to safely handle heavy pieces.
3) Cleaning all parts thoroughly before assembly.
4) Assembling the components in reverse order, applying anti-seize compound and determining the correct number of shims to achieve proper bearing preload.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...paws21610697
The document provides instructions to disassemble a swing drive for a 345B II MH excavator. Key steps include:
1. Draining the oil and removing covers and gears to access the internal components.
2. Using punches and hammers to remove pins holding planetary gears to disassemble the carrier assembly.
3. Removing the ring gear, carrier assembly, and other internal parts which require multiple people due to weights over 35 kg.
The purpose is to fully disassemble the swing drive to facilitate repair or replacement of internal components.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...uddksemd8ud
The document provides instructions to disassemble a swing drive for an excavator. Key steps include: draining fluids from the swing drive; removing the cover, sun gear, carrier assembly, ring gear, and other components; and disassembling the carrier assembly by removing planetary gears, shafts, and bearings. Tools and lifting devices are required to remove some heavy components weighing up to 268 kg. Safety precautions are noted such as containing fluids and avoiding damage to parts.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f8usiedkdmm
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear, sun gear, and other large internal components from the swing drive housing.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f7djidksmd3e
The document provides instructions to disassemble a swing drive for a 345B II MH excavator. Key steps include:
1. Draining the oil and removing covers and gears to access the internal components.
2. Using punches and hammers to remove pins holding planetary gears to disassemble the carrier assembly.
3. Removing the ring gear, carrier assembly, and other internal parts which require multiple people due to weights over 35 kg.
The purpose is to fully disassemble the swing drive to facilitate repair or replacement of internal components.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...jdjkskmikdkmd
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear and other large components from the swing drive housing.
Caterpillar cat 345 b ii mh excavator (prefix apb) service repair manual (apb...f8isoeidkdk
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear and other large components from the swing drive housing.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual Insta...yan77xunhao
The document provides instructions for disassembling the swing drive of an excavator. Key steps include: draining fluids from the swing drive; removing the cover, gears, and carrier assembly; disassembling the carrier assembly by removing planetary gears; and removing the ring gear and housing components. Tools and safety precautions are also outlined. The process is detailed over multiple steps to fully disassemble the swing drive components.
Caterpillar Cat 365B II EXCAVATOR (Prefix JMB) Service Repair Manual (JMB0000...f7djidksmd3e
The document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals, and housing components.
2. Cleaning all parts thoroughly before assembly.
3. Assembling components in reverse order, applying anti-seize compound and determining correct shim thickness to set bearing preload.
4. Installing new seals using special tools and ensuring seals remain undamaged during assembly.
Caterpillar Cat 365B II EXCAVATOR (Prefix JMB) Service Repair Manual (JMB0000...f8usiedkdmm
The document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals, and housing components.
2. Cleaning all parts thoroughly before assembly.
3. Assembling components in reverse order, applying anti-seize compound and determining correct shim thickness to set bearing preload.
4. Installing new seals using special tools and ensuring seals remain undamaged during assembly.
Caterpillar Cat 365B II EXCAVATOR (Prefix JMB) Service Repair Manual (JMB0000...paws21610697
The document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals, and housing components.
2. Cleaning all parts thoroughly before assembly.
3. Assembling components in reverse order, applying anti-seize compound and determining correct shim thickness to set bearing preload.
4. Installing new seals using special tools and ensuring seals remain undamaged during assembly.
Caterpillar Cat 365B II EXCAVATOR (Prefix JMB) Service Repair Manual (JMB0000...uddksemd8ud
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. It describes in detail how to remove over 30 individual parts in 16 steps. Key steps include removing the final drive cover, ring gear, carrier assemblies, gears, shafts and bearings. Reassembly requires cleaning all parts, applying anti-seize compound, installing bearings and seals, and adjusting shims to achieve the proper bearing preload. Precise instructions and illustrations are provided for each step.
Caterpillar Cat 365B II EXCAVATOR (Prefix JMB) Service Repair Manual (JMB0000...jdjkskmikdkmd
The document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals, and housing components.
2. Cleaning all parts thoroughly before assembly.
3. Assembling components in reverse order, applying anti-seize compound and determining correct shim thickness to set bearing preload.
4. Installing new seals using special tools and ensuring seals remain undamaged during assembly.
Caterpillar cat 365 b ii excavator (prefix jmb) service repair manual (jmb000...fios9dkksd
The document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals, and housing components.
2. Cleaning all parts thoroughly before assembly.
3. Assembling components in reverse order, applying anti-seize compound and determining correct shim thickness to set bearing preload.
4. Installing new seals using special tools and ensuring seals remain undamaged during assembly.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B4N) Service Repair Manual Instant ...yan77xunhao
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the cylinder head, applying anti-seize compound to bolts, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other components like the rocker arm first, ensuring timing marks are aligned, and lubricating the camshaft lobes during installation.
- Removing and installing the camshaft gear by pressing it off the camshaft, aligning the keyway, and heating the gear to the proper temperature during installation.
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
CASE CX700 CRAWLER EXCAVATOR Service Repair Manual Instant Download.pdfyan77xunhao
CASE/AKCELA hydraulic fluid is recommended for use in the hydraulic system. The specific fluid to use depends on the ambient temperature range. For temperate climates from -20°C to +40°C, use CASE/AKCELA HYDRAULIC EXCAVATOR FLUID. For hot climates from 0°C to +50°C, use CASE/AKCELA AW HYDRAULIC FLUID 68 HV.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling major transmission components like gears, shafts, bearings, springs and seals. Proper cleaning and lubrication of parts is emphasized. Safety notes warn of risks from improper handling of spring-loaded components.
The document provides instructions for removing and installing the boom on a 420F Backhoe Loader. It describes:
1) Disconnecting hoses and removing pins/bolts to separate the boom from the loader.
2) Using pullers and lifting devices to remove bearings and the boom cylinder.
3) Reversing the process to install the new or repaired boom by pressing in bearings and reattaching components.
This document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles
- Loosening the threaded nut and removing the nozzle and seat washer from the cylinder block
- Cleaning parts and installing a new seat washer before installing the nozzle
- Carefully tightening the nut to the specified torque
More Related Content
Similar to Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual Instant Download.pdf
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual Instant ...jiuliu14811471
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and verifying seal installation. Proper cleaning and torqueing of fasteners is emphasized.
Caterpillar Cat 365B II EXCAVATOR (Prefix DER) Service Repair Manual Instant ...qianxu35543635
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. It describes:
1) Disassembling the various components of the final drive by removing bolts, pins, gears, and other parts.
2) Properly supporting components with tooling as they are removed to safely handle heavy pieces.
3) Cleaning all parts thoroughly before assembly.
4) Assembling the components in reverse order, applying anti-seize compound and determining the correct number of shims to achieve proper bearing preload.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...paws21610697
The document provides instructions to disassemble a swing drive for a 345B II MH excavator. Key steps include:
1. Draining the oil and removing covers and gears to access the internal components.
2. Using punches and hammers to remove pins holding planetary gears to disassemble the carrier assembly.
3. Removing the ring gear, carrier assembly, and other internal parts which require multiple people due to weights over 35 kg.
The purpose is to fully disassemble the swing drive to facilitate repair or replacement of internal components.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...uddksemd8ud
The document provides instructions to disassemble a swing drive for an excavator. Key steps include: draining fluids from the swing drive; removing the cover, sun gear, carrier assembly, ring gear, and other components; and disassembling the carrier assembly by removing planetary gears, shafts, and bearings. Tools and lifting devices are required to remove some heavy components weighing up to 268 kg. Safety precautions are noted such as containing fluids and avoiding damage to parts.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f8usiedkdmm
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear, sun gear, and other large internal components from the swing drive housing.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f7djidksmd3e
The document provides instructions to disassemble a swing drive for a 345B II MH excavator. Key steps include:
1. Draining the oil and removing covers and gears to access the internal components.
2. Using punches and hammers to remove pins holding planetary gears to disassemble the carrier assembly.
3. Removing the ring gear, carrier assembly, and other internal parts which require multiple people due to weights over 35 kg.
The purpose is to fully disassemble the swing drive to facilitate repair or replacement of internal components.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...jdjkskmikdkmd
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear and other large components from the swing drive housing.
Caterpillar cat 345 b ii mh excavator (prefix apb) service repair manual (apb...f8isoeidkdk
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear and other large components from the swing drive housing.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual Insta...yan77xunhao
The document provides instructions for disassembling the swing drive of an excavator. Key steps include: draining fluids from the swing drive; removing the cover, gears, and carrier assembly; disassembling the carrier assembly by removing planetary gears; and removing the ring gear and housing components. Tools and safety precautions are also outlined. The process is detailed over multiple steps to fully disassemble the swing drive components.
Caterpillar Cat 365B II EXCAVATOR (Prefix JMB) Service Repair Manual (JMB0000...f7djidksmd3e
The document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals, and housing components.
2. Cleaning all parts thoroughly before assembly.
3. Assembling components in reverse order, applying anti-seize compound and determining correct shim thickness to set bearing preload.
4. Installing new seals using special tools and ensuring seals remain undamaged during assembly.
Caterpillar Cat 365B II EXCAVATOR (Prefix JMB) Service Repair Manual (JMB0000...f8usiedkdmm
The document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals, and housing components.
2. Cleaning all parts thoroughly before assembly.
3. Assembling components in reverse order, applying anti-seize compound and determining correct shim thickness to set bearing preload.
4. Installing new seals using special tools and ensuring seals remain undamaged during assembly.
Caterpillar Cat 365B II EXCAVATOR (Prefix JMB) Service Repair Manual (JMB0000...paws21610697
The document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals, and housing components.
2. Cleaning all parts thoroughly before assembly.
3. Assembling components in reverse order, applying anti-seize compound and determining correct shim thickness to set bearing preload.
4. Installing new seals using special tools and ensuring seals remain undamaged during assembly.
Caterpillar Cat 365B II EXCAVATOR (Prefix JMB) Service Repair Manual (JMB0000...uddksemd8ud
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. It describes in detail how to remove over 30 individual parts in 16 steps. Key steps include removing the final drive cover, ring gear, carrier assemblies, gears, shafts and bearings. Reassembly requires cleaning all parts, applying anti-seize compound, installing bearings and seals, and adjusting shims to achieve the proper bearing preload. Precise instructions and illustrations are provided for each step.
Caterpillar Cat 365B II EXCAVATOR (Prefix JMB) Service Repair Manual (JMB0000...jdjkskmikdkmd
The document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals, and housing components.
2. Cleaning all parts thoroughly before assembly.
3. Assembling components in reverse order, applying anti-seize compound and determining correct shim thickness to set bearing preload.
4. Installing new seals using special tools and ensuring seals remain undamaged during assembly.
Caterpillar cat 365 b ii excavator (prefix jmb) service repair manual (jmb000...fios9dkksd
The document provides instructions for disassembling and assembling the final drive of an excavator. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals, and housing components.
2. Cleaning all parts thoroughly before assembly.
3. Assembling components in reverse order, applying anti-seize compound and determining correct shim thickness to set bearing preload.
4. Installing new seals using special tools and ensuring seals remain undamaged during assembly.
Similar to Caterpillar Cat 345B II EXCAVATOR (Prefix FEE) Service Repair Manual Instant Download.pdf (16)
Caterpillar Cat 330C FM EXCAVATOR (Prefix B4N) Service Repair Manual Instant ...yan77xunhao
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the cylinder head, applying anti-seize compound to bolts, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other components like the rocker arm first, ensuring timing marks are aligned, and lubricating the camshaft lobes during installation.
- Removing and installing the camshaft gear by pressing it off the camshaft, aligning the keyway, and heating the gear to the proper temperature during installation.
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
CASE CX700 CRAWLER EXCAVATOR Service Repair Manual Instant Download.pdfyan77xunhao
CASE/AKCELA hydraulic fluid is recommended for use in the hydraulic system. The specific fluid to use depends on the ambient temperature range. For temperate climates from -20°C to +40°C, use CASE/AKCELA HYDRAULIC EXCAVATOR FLUID. For hot climates from 0°C to +50°C, use CASE/AKCELA AW HYDRAULIC FLUID 68 HV.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling major transmission components like gears, shafts, bearings, springs and seals. Proper cleaning and lubrication of parts is emphasized. Safety notes warn of risks from improper handling of spring-loaded components.
The document provides instructions for removing and installing the boom on a 420F Backhoe Loader. It describes:
1) Disconnecting hoses and removing pins/bolts to separate the boom from the loader.
2) Using pullers and lifting devices to remove bearings and the boom cylinder.
3) Reversing the process to install the new or repaired boom by pressing in bearings and reattaching components.
This document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 3054 engine. It describes:
- Removing fuel injection lines before removing nozzles
- Loosening the threaded nut and removing the nozzle and seat washer from the cylinder block
- Cleaning parts and installing a new seat washer before installing the nozzle
- Carefully tightening the nut to the specified torque
Caterpillar Cat 345B Series II Excavator (Prefix CCC) Service Repair Manual I...yan77xunhao
The document provides instructions for removing and installing the rocker shaft, pushrods, cylinder head, and related components on a 345B Series II Excavator with a 3176C engine. The removal procedure involves disconnecting sensors, tubes, and wiring before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning mating surfaces, installing new gaskets and seals, and using guide bolts to position the cylinder head before reconnecting components.
This document provides instructions for removing the cylinder head from a Caterpillar 3054C engine. The steps include:
1. Draining the coolant and engine oil from the engine oil cooler.
2. Removing the air filter hose.
3. Removing any attached components to the cylinder head like the valve cover, rocker arms, pushrods, etc.
4. Removing the cylinder head bolts and removing the cylinder head.
The document provides instructions for disassembling and assembling components of the control valve for an excavator model 385B. It describes 25 steps to disassemble parts like actuators, manifolds, solenoids, valves, seals and more. The assembly section outlines 14 steps and provides warnings to properly install spring-loaded parts to prevent injury. Precautions are noted to clean parts and check for wear before reassembly.
Caterpillar Cat 385C and 385C L Excavator (Prefix JCM) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Tools, torque specs and notes on lubrication and seals are provided. The goal is to disassemble, clean, inspect for wear, replace worn parts, and reassemble the final drive while maintaining cleanliness.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. It describes:
1) Removing over 30 components of the final drive including gears, shafts, housings and seals using various tools.
2) Cleaning and inspecting parts prior to assembly.
3) Assembling the components in reverse order, applying lubricants to bearings and sealing surfaces.
4) Using tools and procedures to properly set bearing preload when installing the main housing.
Caterpillar Cat 385B and 385B L Excavator (Prefix FDL) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
Caterpillar Cat 374F L Excavator (Prefix AP4) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of a 374F L Excavator. It lists the required tools and parts. The disassembly process involves removing components like the final drive cover, ring gear, carrier assemblies, gears, shafts and housings. The assembly process specifies cleaning parts, applying sealant, installing bearings and seals, and adjusting bearing preload using shims. Precautions are given for using hydraulic cylinders and puller studs during the assembly process.
This document provides instructions for disassembling and assembling the governor and fuel injection pump housing of a 3306 vehicular engine. It describes removing over 30 individual parts in 12 steps to disassemble the governor. It then describes assembling the governor in 35 steps, noting to clean and oil all parts before assembly.
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifter group
- Camshaft
- Camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep parts clean and properly support components.
The document provides instructions for removing and disassembling the transmission of a 428D Backhoe Loader. It describes 19 steps to disassemble the transmission into its major components which include removing valve groups, filters, shafts, seals and gaskets. Special tools are required and cleanliness is important when disassembling the transmission.
The document provides instructions for removing the bank valve from a 420E Backhoe Loader. It is a 19 step process that involves draining fluids, removing floor plates, disconnecting hoses and wiring, and using lifting equipment to remove the heavy bank valve unit. The bank valve is then disassembled into its individual valve components for inspection or replacement.
The document provides instructions for installing a swing frame on a 420E backhoe loader. It outlines 20 steps for the installation, which include lowering bearing temperatures, placing bars through frames, installing pins and bolts, connecting hoses and harnesses, and positioning cylinders. Tools required include levers, drivers, and lifting devices. Safety precautions are provided for working on pressurized hydraulic systems.
The document provides instructions to disassemble an axle housing, axle shaft, and wheel flange from a 420E backhoe loader. It outlines 9 steps to remove components including the axle shaft, retaining rings, locking plates, seals, bearings and bushings. Tools required include a spanner wrench, retaining ring pliers, and a combination puller. The purpose is to disassemble these components for repair or replacement.
The document provides instructions for removing and installing components related to the steering and final drive system of a Caterpillar 420E backhoe loader, including:
- Removing and installing the front tire and rim.
- Removing and installing the tie rod and steering cylinder.
- Removing the final drive planetary by draining oil and removing mounting screws.
- Disassembling the final drive planetary by using retaining ring pliers to remove the retaining ring.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B 1P-2420 Transmission Repair Stand 1
C
5P-5197 Retaining Ring Pliers As 1
1U-8759 Tip Set 1
D 1P-0510 Driver Gp 1
Start By:
A. Remove the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Remove and
Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00724836
2/13
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 1. Attach Tooling (A) and a suitable lifting device to the swing drive.
2. Position the swing drive on Tooling (B). The weight of the swing drive is approximately
268 kg (570 lb).
3. Open the drain valve, and drain the oil from the swing drive into a suitable container for
storage or disposal. The capacity of the swing drive is approximately 11 L (2.9 US gal). If
necessary, remove the drain valve from the swing drive housing.
Illustration 2 g00724832
4. Remove oil level gauge (Dipstick) (1), the filler breather cap assembly, and hose assembly
(2) from the swing drive.
Illustration 3 g00724843
5. Remove fitting (3) from cover (5) .
6. Remove bolts (4) and the washers from cover (5) .
3/13
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00724840
7. Attach Tooling (A) and a suitable lifting device to cover (5). Remove cover (5) .
Illustration 5 g00724854
8. Remove sun gear (6) from the carrier assembly (7) .
Illustration 6 g00724856
9. Remove spacer (8) from carrier assembly (7) .
4/13
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 10. Remove carrier assembly (7) from the swing drive.
11. Disassemble carrier assembly (7), as follows:
Illustration 7 g00724860
a. Use a hammer and a punch in order to drive spring pin (9) into planetary shaft (10) .
Illustration 8 g00724862
b. Remove planetary shaft (10), thrust washers (11) and (14), and planetary gear (12)
from the carrier.
c. Remove bearing (13) from planetary gear (12) .
d. Use a hammer and a punch in order to remove spring pin (9) from the planetary shaft
(10) .
e. Repeat Steps 11.a through 11.d in order to remove the remaining planetary gears from
the carrier.
5/13
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g00724866
12. Use a screwdriver in order to remove the upper retaining ring (15) from sun gear (16) .
13. Remove carrier (7) from sun gear (17) .
Illustration 10 g00725145
14. Remove retaining ring (17) from the sun gear.
Illustration 11 g00725166
6/13
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 15. Attach Tooling (A) and a suitable lifting device to ring gear (18) .
16. Remove ring gear (18) from the swing drive housing (19). The weight of ring gear (18) is
approximately 36 kg (80 lb).
Illustration 12 g00725186
17. Remove spacer (20) from carrier assembly (21) .
Illustration 13 g00725194
18. Use two screwdrivers in order to remove retaining ring (22) .
7/13
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00725203
19. Use two people to remove carrier assembly (21). The weight of carrier assembly (21) is
approximately 40 kg (88 lb).
20. Disassemble carrier assembly (21), as follows:
Illustration 15 g00725252
a. Use a hammer and a punch to drive spring pin (23) into planetary shaft (24) .
Illustration 16 g00725260
8/13
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. b. Remove planetary shaft (24), thrust washers (25) and (29), and planetary gear (27)
from the carrier.
c. Remove bearings (26) and (28) from planetary gear (27) .
d. Use a hammer and a punch to remove spring pin (23) from planetary shaft (24) .
e. Repeat Steps 20.a through 20.d in order to remove the remaining planetary gears from
the carrier.
Illustration 17 g00725270
21. Use Tooling (C) to remove retaining ring (30) .
Illustration 18 g00725274
22. Place swing drive housing (19) sideways. The weight of swing drive housing (19) is
approximately 73 kg (160 lb). Remove bolts (32) and the washers from bearing cage (31) .
9/13
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 19 g00725297
23. Put swing drive housing (19) in a press. The combined weight of the swing drive housing
(19), the pinion shaft, and the bearing cage is approximately 152 kg (335 lb).
Illustration 20 g00725301
24. Place steel supports (d) under the face of bearing cage (31), as shown.
25. Place a wood block directly under the pinion shaft (33). This will prevent the pinion shaft
from falling, while the shaft is pressed out of the swing drive housing.
Note: Use care when components are pushed from the swing drive housing. Avoid injury to
personnel. Also, avoid damage to components.
26. Push pinion shaft (33) from the swing drive housing. The weight of pinion shaft (33) is
approximately 41 kg (90 lb).
27. Remove the swing drive housing and the pinion shaft from the press.
10/13
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engi...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g00725386
28. Place swing drive housing (19) sideways. The weight of swing drive housing (19) is
approximately 73 kg (160 lb).
29. Remove remaining bolts (32), the washers, and bearing cage (31) from swing drive housing
(19) .
Illustration 22 g00725388
30. Remove lip seals (34) and O-ring seal (35) from bearing cage (31) .
11/13
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engi...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g00725300
31. Remove bearing cone (36) from the smaller bearing.
Illustration 24 g00725383
32. Use the following procedure to remove bearing assembly (37), spacer (38), and bearing
assembly (39) .
Illustration 25 g00725391
a. Place the bearings and the swing drive housing under a press.
b. Use Tooling (D) and spacer (38) in order to remove bearing assembly (39) from the
swing drive housing.
Note: Use care when components are pushed from the swing drive housing. Avoid
injury to personnel. Also, avoid damage to components.
Note: Bearing assembly (39) will be damaged upon the removal.
12/13
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engi...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 26 g00725394
c. Remove bearing assembly (37) from the swing drive housing (19) .
Note: Push on the outer race in order to prevent damage to bearing assembly (37) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Sep 20 18:26:18 UTC+0800 2020
13/13
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engi...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B II EXCAVATOR FEE
Configuration: 345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine
Disassembly and Assembly
345B, 345B Series II and W345B Series II Excavators Machine Systems
Media Number -SENR1934-11 Publication Date -01/01/2012 Date Updated -12/01/2012
i02830548
Swing Drive - Assemble
SMCS - 5459-016
S/N - AGS1-UP
S/N - AKX1-UP
S/N - ALB1-UP
S/N - ALD1-UP
S/N - AMD1-UP
S/N - AMJ1-UP
S/N - AMN1-UP
S/N - ANJ1-UP
S/N - APB1-UP
S/N - AYR1-UP
S/N - CCC1-UP
S/N - CDY1-UP
S/N - DCW1-UP
S/N - DET1-UP
S/N - FEE1-UP
Assembly Procedure
1/14
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B 1P-2420 Transmission Repair Stand 1
C
5P-5197 Retaining ring pliers 1
1U-8759 Tip Set 1
D 1P-0510 Drive Group 1
E 1U-6396 O-Ring Assembly Compound 1
F 5P-3931 Anti-Seize Compound 1
G 5P-0960 Molybdenum Grease 1
H 9S-3263 Thread Lock Compound 1
J 1U-8846 Gasket Sealant 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use Tooling (E) during the assembly procedure.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Make sure that all parts of the swing drive are thoroughly clean and free of dirt and debris
prior to assembly.
2/14
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00725394
2. Apply Tooling (F) on the outside diameter of bearing (37) and the inside diameter of swing
drive housing (19) .
3. Lower the temperature of bearing (37) . Install bearing (37) in the swing drive housing.
Illustration 2 g00725388
4. Install O-ring seal (35) into bearing cage (31) .
5. Install the two lip seals (34) in bearing cage (31) .
6. Apply Tooling (G) on the lip of each seal.
3/14
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00725547
7. Carefully install cage (31) over pinion shaft (33) .
Illustration 4 g00725554
8. Heat bearing (39) to a temperature of 135 °C (275 °F) and install bearing (39) on the pinion
shaft (33) .
Illustration 5 g00725572
4/14
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 9. Install spacer (38) on top of bearing (37) , as shown.
Note: Lip (e) for spacer (38) must face opposite bearing (37) , as shown.
Illustration 6 g00725575
10. Put swing drive housing (19) in the press.
11. Apply Tooling (F) on the outside diameter of bearing (39) and the inside diameter of the
swing drive housing.
12. Install pinion shaft (33) , bearing cage (31) , bearing assembly (39) , through spacer (38)
and bearing (37) .
Note: It may be necessary to reposition the press so that bearing assembly (39) is installed
evenly into the swing drive housing.
Note: Align bearing cage (31) with the swing drive housing during installation of the pinion
shaft. Temporarily install two bolts that will hold bearing cage (31) to the swing drive
housing.
Illustration 7 g00725595
5/14
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 13. Remove the swing drive from the press and place the swing drive sideways. The combined
weight of the swing drive housing, the pinion shaft, and the bearing cage is 152 kg (335 lb).
14. Remove the temporary bolts that are holding the bearing cage in position.
15. Apply Tooling (H) on the threads of bolts (32) that hold bearing cage (31) to swing drive
housing (19) .
16. Tighten bolts (32) to a torque of 100 ± 20 N·m (75 ± 15 lb ft).
Illustration 8 g00725607
17. Heat bearing cone (36) to a temperature of 135 °C (275 °F). Install bearing cone (36) on the
pinion shaft (33) .
Note: Make sure that the shaft is centered in the swing drive housing, before you install
bearing cone (36) .
Illustration 9 g00725270
18. Use Tooling (C) to install retaining ring (30) .
19. Assemble the carrier assembly (21) , as follows:
6/14
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 10 g00725260
a. Apply clean SAE 30W oil on bearing (26) and bearing (28) . Install bearings (26) and
(28) into planetary gear (27) .
b. Install thrust washer (25) on one side of planetary gear (27) .
c. Install thrust washer (29) on the opposite side of planetary gear (27) .
d. Use a deburring tool in order to remove the metal burr from the openings in the
carrier.
e. Install planetary gear (27) and the thrust washers in the carrier assembly (21) .
Illustration 11 g00725252
f. Install planetary shaft (24) through the gear assembly into the carrier assembly. Make
sure that the spring pin hole in the planetary shaft is in alignment with the spring pin
hole in the carrier.
7/14
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 12 g00703700
g. Drive spring pin (23) into shaft (24) . Orient the split in spring pin (23) vertically to
the carrier. Align the split in the spring pin to the top or to the bottom. Make a stake
mark on each side of the spring pin hole in the carrier. Each stake mark should be
approximately 2.25 ± 0.75 mm (0.09 ± 0.03 inch) from the outside diameter of the
spring pin hole.
h. Repeat Steps 19.a through 19.g in order to install the remaining planetary gears (27)
in the carrier.
Illustration 13 g00725203
20. Use two people and install carrier assembly (21) into the housing. The weight of carrier
assembly (21) is approximately 40 kg (88 lb).
8/14
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 14 g00725194
21. Install retaining ring (22) .
Illustration 15 g00725186
22. Install spacer (20) into carrier assembly (21) .
Illustration 16 g00725166
9/14
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engine(...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 23. Make sure that the mating surfaces of the ring gear (18) and the swing drive housing (19)
are thoroughly clean.
24. Apply Tooling (J) to the face of swing drive housing (19) and the face of ring gear (18) .
25. Install Tooling (A) onto ring gear (18) . Weight of the ring gear is approximately 36 kg (80
lb).
26. Install ring gear (18) onto the swing drive housing (19) .
Illustration 17 g00725145
27. Install retaining ring (17) into the sun gear.
Illustration 18 g00724866
28. Install carrier (7) into the sun gear. Install retaining ring (15) into sun gear (16) .
29. Assemble carrier assembly (7) , as follows:
10/14
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engi...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 19 g00724862
a. Apply clean SAE 30W oil on bearing (13) . Install bearing (13) in planetary gear
(12) .
b. Install a thrust washer (11) on one side of planetary gear (12) .
c. Install a thrust washer (14) on the opposite side of planetary gear (12) .
d. Use a deburring tool in order to remove the metal burr from the openings in the
carrier.
e. Install planetary gear (12) and the thrust washers in the carrier assembly (7) .
Illustration 20 g00724860
f. Install planetary shaft (10) through the gear assembly into the carrier assembly. Make
sure that the spring pin hole in the planetary shaft is in alignment with the spring pin
hole in the carrier.
11/14
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engi...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 21 g00703700
g. Drive spring pin (9) into shaft (10) . Orient the split in spring pin (9) vertically to the
carrier. Align the split in the spring pin to the top or to the bottom. Make a stake mark
on each side of the spring pin hole in the carrier. Each stake mark should be
approximately 2.25 ± 0.75 mm (0.09 ± 0.03 inch) from the outside diameter of the
spring pin hole.
h. Repeat Steps 29.a through 29.g for the remaining gear assemblies.
Illustration 22 g00724856
30. Install carrier assembly (7) in the ring gear.
31. Install spacer (8) into carrier assembly (7) .
12/14
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engi...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. Illustration 23 g00724854
32. Install sun gear (6) into carrier assembly (7) .
Illustration 24 g00724840
33. Make sure that the mating surfaces of the ring gear and cover (5) are thoroughly clean.
34. Apply Tooling (J) on the flange surface of the ring gear and cover (5) .
35. Fasten Tooling (A) and a suitable lifting device to cover (5) . Put the cover in the original
position on the ring gear. Make sure that the cover is seated properly.
13/14
345B Series II Excavator FEE00001-UP (MACHINE) POWERED BY 3176C Engi...
2020/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...