This service repair manual provides detailed instructions for assembling a travel motor for a 345B Excavator model in 33 steps, including installing piston assemblies, cam plates, bearings, seals, and adjusting spacer measurements to specified tolerances.
This document provides assembly instructions for installing a travel motor on a 345B Excavator. It outlines 33 steps to assemble parts like pistons, seals, plates and valves inside the travel motor housing. It then describes 4 steps for installing the assembled travel motor which include cleaning surfaces, replacing an O-ring seal, installing a coupling, and using lifting tools to slide the motor into the final drive housing.
This document provides assembly instructions for installing a travel motor on a 345B Excavator. It outlines 33 steps to assemble parts like pistons, seals, plates and valves inside the travel motor housing. It then describes 4 steps for installing the assembled travel motor which include cleaning surfaces, replacing an O-ring seal, installing a coupling, and using lifting tools to slide the motor into the final drive housing.
This document provides assembly instructions for installing a travel motor on a 345B Excavator. It outlines 33 steps to assemble parts like the piston, barrel, shaft and head. Tools needed are listed. Cleanliness is important to prevent contaminating the hydraulic system. Measurements are checked at various steps to ensure proper assembly.
This document provides assembly instructions for installing a travel motor on a 345B Excavator. It outlines 33 steps to assemble parts like pistons, seals, plates and valves inside the travel motor housing. It then describes 4 steps for installing the assembled travel motor which include cleaning surfaces, replacing an O-ring seal, installing a coupling, and using lifting tools to slide the motor into the final drive housing.
Caterpillar cat 345 b excavator (prefix amj) service repair manual (amj00001 ...kmf9ioseodk
The document provides assembly instructions for a travel motor in 3 steps:
1. It describes preparing the travel motor components and inserting keys, seals, pistons, plates and spacers into the motor body.
2. It explains assembling the barrel, installing the shaft and bearings, and inserting friction disks and separator plates.
3. It outlines attaching the head, installing valves, plugs and seals to complete the assembly. Precise measurements and torque specifications are listed to ensure correct assembly.
The document provides assembly instructions for a travel motor in 3 steps:
1. It describes preparing the travel motor components and inserting keys, seals, pistons, plates and spacers into the motor body.
2. It explains assembling the barrel, installing the shaft and bearings, and inserting friction disks and separator plates.
3. It outlines attaching the head, installing valves, plugs and seals to complete the assembly. Precise measurements and torque specifications are listed to ensure correct assembly.
The document provides assembly instructions for a travel motor in 3 steps:
1. It describes preparing the travel motor components and inserting keys, seals, pistons, plates and spacers into the motor body.
2. It explains assembling the barrel, installing the shaft and bearings, and inserting friction disks and separator plates.
3. It outlines attaching the head, installing valves, plugs and seals to complete the assembly. Precise measurements and torque specifications are listed to ensure correct assembly.
Caterpillar cat 345 b excavator (prefix amj) service repair manual (amj00001 ...fjsekdmmeed
This document provides assembly instructions for installing a travel motor on a 345B Excavator. It outlines 33 steps to assemble parts like seals, pistons, plates, and shafts inside the travel motor housing. It then describes 4 steps to install the assembled travel motor onto the final drive, including cleaning surfaces, replacing an O-ring seal, and using lifting tools to maneuver the motor into position. Proper torque specifications are given for tightening fasteners.
This document provides assembly instructions for installing a travel motor on a 345B Excavator. It outlines 33 steps to assemble parts like pistons, seals, plates and valves inside the travel motor housing. It then describes 4 steps for installing the assembled travel motor which include cleaning surfaces, replacing an O-ring seal, installing a coupling, and using lifting tools to slide the motor into the final drive housing.
This document provides assembly instructions for installing a travel motor on a 345B Excavator. It outlines 33 steps to assemble parts like pistons, seals, plates and valves inside the travel motor housing. It then describes 4 steps for installing the assembled travel motor which include cleaning surfaces, replacing an O-ring seal, installing a coupling, and using lifting tools to slide the motor into the final drive housing.
This document provides assembly instructions for installing a travel motor on a 345B Excavator. It outlines 33 steps to assemble parts like the piston, barrel, shaft and head. Tools needed are listed. Cleanliness is important to prevent contaminating the hydraulic system. Measurements are checked at various steps to ensure proper assembly.
This document provides assembly instructions for installing a travel motor on a 345B Excavator. It outlines 33 steps to assemble parts like pistons, seals, plates and valves inside the travel motor housing. It then describes 4 steps for installing the assembled travel motor which include cleaning surfaces, replacing an O-ring seal, installing a coupling, and using lifting tools to slide the motor into the final drive housing.
Caterpillar cat 345 b excavator (prefix amj) service repair manual (amj00001 ...kmf9ioseodk
The document provides assembly instructions for a travel motor in 3 steps:
1. It describes preparing the travel motor components and inserting keys, seals, pistons, plates and spacers into the motor body.
2. It explains assembling the barrel, installing the shaft and bearings, and inserting friction disks and separator plates.
3. It outlines attaching the head, installing valves, plugs and seals to complete the assembly. Precise measurements and torque specifications are listed to ensure correct assembly.
The document provides assembly instructions for a travel motor in 3 steps:
1. It describes preparing the travel motor components and inserting keys, seals, pistons, plates and spacers into the motor body.
2. It explains assembling the barrel, installing the shaft and bearings, and inserting friction disks and separator plates.
3. It outlines attaching the head, installing valves, plugs and seals to complete the assembly. Precise measurements and torque specifications are listed to ensure correct assembly.
The document provides assembly instructions for a travel motor in 3 steps:
1. It describes preparing the travel motor components and inserting keys, seals, pistons, plates and spacers into the motor body.
2. It explains assembling the barrel, installing the shaft and bearings, and inserting friction disks and separator plates.
3. It outlines attaching the head, installing valves, plugs and seals to complete the assembly. Precise measurements and torque specifications are listed to ensure correct assembly.
Caterpillar cat 345 b excavator (prefix amj) service repair manual (amj00001 ...fjsekdmmeed
This document provides assembly instructions for installing a travel motor on a 345B Excavator. It outlines 33 steps to assemble parts like seals, pistons, plates, and shafts inside the travel motor housing. It then describes 4 steps to install the assembled travel motor onto the final drive, including cleaning surfaces, replacing an O-ring seal, and using lifting tools to maneuver the motor into position. Proper torque specifications are given for tightening fasteners.
Caterpillar cat 345 b excavator (prefix amj) service repair manual (amj00001 ...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1. It describes preparing the travel motor components and inserting keys, seals, pistons, plates and spacers into the motor body.
2. It explains assembling the barrel, installing the shaft and bearings, and inserting friction disks and separator plates.
3. It outlines attaching the head, installing valves, plugs and seals to complete the assembly. Precise measurements and torque specifications are listed to ensure correct assembly.
Caterpillar Cat 345B L EXCAVATOR (Prefix 8RW) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for installing a cylinder head on a 345B L EXCAVATOR engine. The steps include:
1. Cleaning the cylinder head and block mating surfaces.
2. Installing the cylinder head gasket and O-rings on the block.
3. Lifting the cylinder head into place and installing bolts.
4. Tightening the bolts in a specific sequence to the correct torques.
5. Installing additional components like the water outlet manifold.
Caterpillar Cat 345B L EXCAVATOR (Prefix 8RW) Service Repair Manual (8RW00001...dujdkksdmm
The document provides instructions for removing and installing a cylinder head and lifter group on a Caterpillar 345B L EXCAVATOR engine. It describes disconnecting various engine components and sensors, removing bolts and gaskets, and lifting the cylinder head off the engine block. It then details cleaning surfaces, installing new gaskets and seals, replacing the cylinder head using a lifting device and specific tightening procedures for the head bolts. Finally, it outlines reconnecting components and filling the cooling system upon completion.
Caterpillar cat 345 b l excavator (prefix 8rw) service repair manual (8rw0000...kmf9ioseodk
This document provides instructions for installing a cylinder head on a 345B L EXCAVATOR engine. It describes cleaning and inspecting the cylinder head and block mating surfaces. The correct cylinder head gasket must be installed, along with new O-rings. The cylinder head is placed on guide bolts and bolts are tightened in a specific sequence to the correct torques. Sensors and lines are then reconnected to the cylinder head before installing the water outlet manifold.
Caterpillar cat 345 b l excavator (prefix 8rw) service repair manual (8rw0000...fujsekfkksemm
This document provides instructions for installing a cylinder head on a 345B L EXCAVATOR engine. It describes cleaning and inspecting the cylinder head and block mating surfaces. The correct cylinder head gasket must be installed, along with new O-rings. The cylinder head is placed on guide bolts and bolts are tightened in a specific sequence to the correct torques. Sensors and lines are then reconnected to the cylinder head before installing the water outlet manifold.
Caterpillar cat 345 b l excavator (prefix 8rw) service repair manual (8rw0000...fjsekdmmeed
The document provides instructions for removing and installing a cylinder head and lifter group on a Caterpillar 345B L EXCAVATOR engine. It describes disconnecting various engine components and sensors, removing bolts and gaskets, and lifting the cylinder head off the engine block. It then details cleaning surfaces, installing new gaskets and seals, bolting the head back onto the block, and reconnecting all components in reverse order. Proper torque specifications are provided for all fasteners.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual components from the pump housing using various tools. The assembly procedure describes installing the components in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Special safety precautions are noted for parts under spring tension.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 70 individual parts in over 40 steps, using various tools. The transmission is first removed from the vehicle and mounted on a stand. Components like gears, shafts, seals and housings are then systematically dismantled using presses, pullers and other tools to remove bearings, seals, springs and other internal pieces. Detailed illustrations accompany each step to show how to access and remove each part.
The document is a service repair manual that provides disassembly instructions for a 430E Backhoe Loader transmission. It lists the required tools and begins by having the transmission removed and installed on an engine stand. It then provides step-by-step instructions to disassemble the various transmission components including removing gears, shafts, seals, and other parts. Detailed illustrations accompany each step.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 430E backhoe loader. It lists the required tools and presents the steps in detail with illustrations. The removal procedure involves removing bolts and lowering the guard with a hydraulic jack to access the drive shaft. Installation is the reverse of removal.
The document provides instructions for assembling the transmission of a 430D Backhoe Loader. It describes installing various transmission components like bearing cups, seals, gears, shafts, and housing in their proper order and orientation. Tolerances for shaft play are also specified to be checked with gauges during assembly. The transmission is then mounted to the vehicle and electrical and hydraulic connections are made.
The document provides instructions for assembling the transmission of a 430D Backhoe Loader. It describes installing various transmission components like bearings, gears, shafts, seals and housing in their proper order and orientation. Tools required for the assembly are listed. Precautions like applying transmission oil and heating bearings to the specified temperature before installation are mentioned. Final steps include installing the transmission in the vehicle and connecting related components.
The document provides instructions for disassembling the transmission of a 420F2 backhoe loader. It describes removing over 20 components from the transmission, including the torque converter, gears, shafts, bearings, seals and other parts. Safety warnings are included to release springs carefully and wear protective equipment. Detailed illustrations accompany each step. The goal is to fully disassemble the transmission down to its individual parts for repair or replacement.
The document provides instructions for assembling a 424D backhoe loader transmission. It describes installing various transmission components like bearing cups, seals, gears, shafts, and housings. It also provides details on final assembly steps, which include applying sealant, installing the transmission case and shafts, and connecting electrical connectors. Tolerances for shaft play are specified to be checked with a dial indicator during assembly.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 422E backhoe loader. It describes:
1) Using a hydraulic jack to support the drive shaft guard while removing bolts and lowering the guard.
2) Removing bolts to detach the front drive shaft.
3) Installing the drive shaft and tightening bolts to the specified torque.
4) Raising and securing the drive shaft guard with new bolts after installation is complete.
This document provides instructions for removing and installing an engine from a Caterpillar 420F2 backhoe loader. It outlines 19 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses, removing mounting hardware, and lifting the engine out. The 18 steps listed to install the engine describe reconnecting wiring, replacing mounting hardware, refilling fluids, and reinstalling removed components. The document is a service repair manual that details the process to remove and install an engine on the specified backhoe loader model.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for installing an engine in a 420F2 backhoe loader. It outlines 17 steps to correctly position and secure the engine, connect related components like the transmission, alternator, and air conditioning, and refill fluids before completing reassembly. Tools including a hydraulic jack and load leveling beam are required. Proper installation ensures the engine operates safely and efficiently.
The document provides instructions for removing and installing the flywheel housing on a 422E Backhoe Loader. To remove the housing, the flywheel must first be removed. Bolts are then removed from the housing and it is lifted off using a device. When installing, dowels and seals are inspected, bolts are used to secure the housing, and torque specifications are provided. The process is intended to provide maintenance for the flywheel housing component.
This document provides instructions for removing and installing the crankshaft rear seal and flywheel housing on a Caterpillar 420F2 backhoe loader with a C4.4 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe how to remove the existing crankshaft rear seal and flywheel housing, clean and inspect components, install a new seal and gasket, and reinstall the housing while torquing bolts to the specified values.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 420F Backhoe Loader. The disassembly procedure involves removing 17 individual parts from the pump housing using various tools. The assembly procedure describes installing the parts in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided for parts that are spring loaded to prevent injury during assembly.
This document provides instructions for installing an engine in a 416F2 backhoe loader. It outlines 17 steps to correctly position and secure the engine, including connecting various components like the transmission, electrical harnesses, air conditioning compressor, and fuel and cooling systems. Proper installation of the engine is critical for safe and reliable operation of the backhoe loader.
More Related Content
Similar to Caterpillar Cat 345B EXCAVATOR (Prefix AMD) Service Repair Manual Instant Download.pdf
Caterpillar cat 345 b excavator (prefix amj) service repair manual (amj00001 ...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1. It describes preparing the travel motor components and inserting keys, seals, pistons, plates and spacers into the motor body.
2. It explains assembling the barrel, installing the shaft and bearings, and inserting friction disks and separator plates.
3. It outlines attaching the head, installing valves, plugs and seals to complete the assembly. Precise measurements and torque specifications are listed to ensure correct assembly.
Caterpillar Cat 345B L EXCAVATOR (Prefix 8RW) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for installing a cylinder head on a 345B L EXCAVATOR engine. The steps include:
1. Cleaning the cylinder head and block mating surfaces.
2. Installing the cylinder head gasket and O-rings on the block.
3. Lifting the cylinder head into place and installing bolts.
4. Tightening the bolts in a specific sequence to the correct torques.
5. Installing additional components like the water outlet manifold.
Caterpillar Cat 345B L EXCAVATOR (Prefix 8RW) Service Repair Manual (8RW00001...dujdkksdmm
The document provides instructions for removing and installing a cylinder head and lifter group on a Caterpillar 345B L EXCAVATOR engine. It describes disconnecting various engine components and sensors, removing bolts and gaskets, and lifting the cylinder head off the engine block. It then details cleaning surfaces, installing new gaskets and seals, replacing the cylinder head using a lifting device and specific tightening procedures for the head bolts. Finally, it outlines reconnecting components and filling the cooling system upon completion.
Caterpillar cat 345 b l excavator (prefix 8rw) service repair manual (8rw0000...kmf9ioseodk
This document provides instructions for installing a cylinder head on a 345B L EXCAVATOR engine. It describes cleaning and inspecting the cylinder head and block mating surfaces. The correct cylinder head gasket must be installed, along with new O-rings. The cylinder head is placed on guide bolts and bolts are tightened in a specific sequence to the correct torques. Sensors and lines are then reconnected to the cylinder head before installing the water outlet manifold.
Caterpillar cat 345 b l excavator (prefix 8rw) service repair manual (8rw0000...fujsekfkksemm
This document provides instructions for installing a cylinder head on a 345B L EXCAVATOR engine. It describes cleaning and inspecting the cylinder head and block mating surfaces. The correct cylinder head gasket must be installed, along with new O-rings. The cylinder head is placed on guide bolts and bolts are tightened in a specific sequence to the correct torques. Sensors and lines are then reconnected to the cylinder head before installing the water outlet manifold.
Caterpillar cat 345 b l excavator (prefix 8rw) service repair manual (8rw0000...fjsekdmmeed
The document provides instructions for removing and installing a cylinder head and lifter group on a Caterpillar 345B L EXCAVATOR engine. It describes disconnecting various engine components and sensors, removing bolts and gaskets, and lifting the cylinder head off the engine block. It then details cleaning surfaces, installing new gaskets and seals, bolting the head back onto the block, and reconnecting all components in reverse order. Proper torque specifications are provided for all fasteners.
Similar to Caterpillar Cat 345B EXCAVATOR (Prefix AMD) Service Repair Manual Instant Download.pdf (6)
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 430F Backhoe Loader. The disassembly procedure involves removing 17 individual components from the pump housing using various tools. The assembly procedure describes installing the components in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Special safety precautions are noted for parts under spring tension.
The document provides step-by-step instructions for disassembling the transmission of a 430E Backhoe Loader. It details removing over 70 individual parts in over 40 steps, using various tools. The transmission is first removed from the vehicle and mounted on a stand. Components like gears, shafts, seals and housings are then systematically dismantled using presses, pullers and other tools to remove bearings, seals, springs and other internal pieces. Detailed illustrations accompany each step to show how to access and remove each part.
The document is a service repair manual that provides disassembly instructions for a 430E Backhoe Loader transmission. It lists the required tools and begins by having the transmission removed and installed on an engine stand. It then provides step-by-step instructions to disassemble the various transmission components including removing gears, shafts, seals, and other parts. Detailed illustrations accompany each step.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 430E backhoe loader. It lists the required tools and presents the steps in detail with illustrations. The removal procedure involves removing bolts and lowering the guard with a hydraulic jack to access the drive shaft. Installation is the reverse of removal.
The document provides instructions for assembling the transmission of a 430D Backhoe Loader. It describes installing various transmission components like bearing cups, seals, gears, shafts, and housing in their proper order and orientation. Tolerances for shaft play are also specified to be checked with gauges during assembly. The transmission is then mounted to the vehicle and electrical and hydraulic connections are made.
The document provides instructions for assembling the transmission of a 430D Backhoe Loader. It describes installing various transmission components like bearings, gears, shafts, seals and housing in their proper order and orientation. Tools required for the assembly are listed. Precautions like applying transmission oil and heating bearings to the specified temperature before installation are mentioned. Final steps include installing the transmission in the vehicle and connecting related components.
The document provides instructions for disassembling the transmission of a 420F2 backhoe loader. It describes removing over 20 components from the transmission, including the torque converter, gears, shafts, bearings, seals and other parts. Safety warnings are included to release springs carefully and wear protective equipment. Detailed illustrations accompany each step. The goal is to fully disassemble the transmission down to its individual parts for repair or replacement.
The document provides instructions for assembling a 424D backhoe loader transmission. It describes installing various transmission components like bearing cups, seals, gears, shafts, and housings. It also provides details on final assembly steps, which include applying sealant, installing the transmission case and shafts, and connecting electrical connectors. Tolerances for shaft play are specified to be checked with a dial indicator during assembly.
The document provides instructions for removing and installing the front drive shaft on a Caterpillar 422E backhoe loader. It describes:
1) Using a hydraulic jack to support the drive shaft guard while removing bolts and lowering the guard.
2) Removing bolts to detach the front drive shaft.
3) Installing the drive shaft and tightening bolts to the specified torque.
4) Raising and securing the drive shaft guard with new bolts after installation is complete.
This document provides instructions for removing and installing an engine from a Caterpillar 420F2 backhoe loader. It outlines 19 steps to remove the engine, which include draining fluids, disconnecting wiring harnesses, removing mounting hardware, and lifting the engine out. The 18 steps listed to install the engine describe reconnecting wiring, replacing mounting hardware, refilling fluids, and reinstalling removed components. The document is a service repair manual that details the process to remove and install an engine on the specified backhoe loader model.
This document provides instructions for removing and installing the flywheel, crankshaft rear seal, and crankshaft wear sleeve on a Caterpillar 3054C engine. The removal procedure describes using tools to guide and support the flywheel during removal. The crankshaft rear seal is non-serviceable and must be replaced with the housing. The crankshaft wear sleeve is removed using a puller. Installation includes heating the ring gear, cleaning components, using tools to align and position parts, and torquing bolts to the specified values.
This document provides instructions for installing an engine in a 420F2 backhoe loader. It outlines 17 steps to correctly position and secure the engine, connect related components like the transmission, alternator, and air conditioning, and refill fluids before completing reassembly. Tools including a hydraulic jack and load leveling beam are required. Proper installation ensures the engine operates safely and efficiently.
The document provides instructions for removing and installing the flywheel housing on a 422E Backhoe Loader. To remove the housing, the flywheel must first be removed. Bolts are then removed from the housing and it is lifted off using a device. When installing, dowels and seals are inspected, bolts are used to secure the housing, and torque specifications are provided. The process is intended to provide maintenance for the flywheel housing component.
This document provides instructions for removing and installing the crankshaft rear seal and flywheel housing on a Caterpillar 420F2 backhoe loader with a C4.4 engine. It includes a list of required tools and step-by-step procedures with illustrations. The procedures describe how to remove the existing crankshaft rear seal and flywheel housing, clean and inspect components, install a new seal and gasket, and reinstall the housing while torquing bolts to the specified values.
This document provides instructions for disassembling and assembling the main hydraulic piston pump on a 420F Backhoe Loader. The disassembly procedure involves removing 17 individual parts from the pump housing using various tools. The assembly procedure describes installing the parts in reverse order and includes steps to properly set the bearing preload using feeler gauges and indicators. Precautions are provided for parts that are spring loaded to prevent injury during assembly.
This document provides instructions for installing an engine in a 416F2 backhoe loader. It outlines 17 steps to correctly position and secure the engine, including connecting various components like the transmission, electrical harnesses, air conditioning compressor, and fuel and cooling systems. Proper installation of the engine is critical for safe and reliable operation of the backhoe loader.
The document provides instructions for disassembling the transmission of a 416E Backhoe Loader. It lists required tools and gives step-by-step instructions with illustrations. Key steps include removing the transmission from the vehicle, then disassembling its major components such as pumps, shafts, gears, seals and housing. Specific instructions are provided for disassembling the front and rear output shafts. Safety precautions are noted for releasing spring forces. The goal is to fully disassemble the transmission into its core components.
1. The document provides instructions for removing and installing various engine components on a Caterpillar 416F2 backhoe loader, including lifters, camshafts, camshaft bearings, and piston cooling jets.
2. The procedures describe using specialized tools to remove parts and ensuring parts are clean before installation.
3. Technicians are advised to mark lifters during removal for correct installation and lubricate parts with oil before reinstallation.
The document provides instructions for installing a flywheel and crankshaft rear seal on a Caterpillar 3054C engine. It describes cleaning and preparing the components, heating the ring gear to install it on the flywheel, installing guide bolts and lifting brackets to position the flywheel, and tightening the bolts to specification. It also explains that the crankshaft rear seal is replaced as an assembly, cleaning the sealing surfaces, lubricating the new seal, using a plastic sleeve to protect the seal during installation, and tightening setscrews to secure the seal housing.
The document provides instructions for removing and installing a flywheel and flywheel housing on a Caterpillar 416E backhoe loader engine. It describes removing the flywheel by uninstalling bolts and lifting it off with support tools. It also details removing the flywheel housing by uninstalling bolts and lifting it off, then reversing the process to install the housing. Precautions are given to keep parts clean and support heavy components during removal and installation.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B EXCAVATOR AMD
Configuration: ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)
Disassembly and Assembly
345B, 345B Series II and W345B Series II Excavators Machine Systems
Media Number -SENR1934-11 Publication Date -01/01/2012 Date Updated -12/01/2012
i01324820
Travel Motor - Assemble - Series II
SMCS - 4351-016
S/N - AGS1-UP
S/N - AKJ1-UP
S/N - AKX1-UP
S/N - ALB1-UP
S/N - ALD1-UP
S/N - AMD1-UP
S/N - AMJ1-UP
S/N - AMN1-UP
S/N - APB1-UP
S/N - AYR1-UP
S/N - CCC1-UP
S/N - DCW1-UP
S/N - DET1-UP
S/N - FEE1-UP
Assembly Procedure
Table 1
1/15
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Required Tools
Tool Part Number Part Description Qty
(A) 180-6533 Seal Driver 1
(B) 6V-7030 Micrometer Depth Gauge 1
(C) 8T-0447 Calipers 1
(D) 4C-8359 Eyebolt 1
(E) 1P-0510 Driver Group 1
(F) 3E-3879 Eyebolt 1
(G) 1P-1862 Pliers 1
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: If a failure occurs, an accurate diagnosis of the cause can prevent a recurrence. Information
is available to analyze failures for piston pumps and motors. Refer to Special Publication,
SEBD0641, "Analyzing Axial Piston Pump and Motor Failures".
Note: Inspect all parts. If any parts are worn or damaged use new parts for replacement. The
installation of used parts during reconditioning is acceptable. Reuse and salvage information is
available on piston pumps. Refer to Guideline For Reusable Parts and Salvage Operations,
SEBF8032, "Piston Pumps and Motors". During reconditioning, correct any conditions that might
have caused the original failure.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound during the
assembly procedure.
Note: Apply a light film of "10W" oil to all components before assembly.
2/15
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 1 g00631019
1. Install O-ring seal (36) on plug (35) .
2. Install piston (34) and the plug in the travel motor body. Tighten the plug to a torque of 430
± 40 N·m (317 ± 30 lb ft).
Illustration 2 g00630992
Illustration 3 g00636553
3/15
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 3. Apply a thin coat of 4C-4030 Thread Lock Compound on the outer surfaces of lip type seal
(33) .
4. Use Tooling (A) and a suitable hammer to drive the lip type seal into the travel motor body.
Drive the seal downward until Tooling (A) makes contact with the travel motor housing.
5. Use Tooling (G) to install retaining ring (32) to the shaft end of the travel motor body.
Illustration 4 g00630986
6. Install two keys (31) inside the travel motor body.
Illustration 5 g00629434
7. Assemble washers (29), inner spacer (30) and outer spacer (28) in the proper orientation, as
shown.
4/15
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 6 g00628110
8. Use Tooling (B) to measure the distance from the outer spacer to the surface of the table.
The distance should be 22.1 ± 0.6 mm (0.87 ± 0.02 inch). If this measurement is off, check
orientation of the washers. If orientation is correct, replace washers and spacers with new
parts.
Illustration 7 g00625917
9. Install inner spacer (28), four washers (25), and outer spacer (27) to barrel (24) .
10. Install guide (26) to the barrel.
5/15
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 8 g00625911
11. Install piston assemblies (23) with retainer (22) in the piston assembly's original bore in
barrel (24) .
Illustration 9 g00625908
12. Install cam plate (21) on the barrel assembly.
Illustration 10 g00666621
6/15
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 11 g00628062
13. Use a suitable press to install bearing (19) onto shaft (18) .
Illustration 12 g00668076
14. Use a suitable press in order to install inner race (20) onto shaft (18) .
Note: Place the two support plates under the lip of shaft (18) .
7/15
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 13 g00626633
15. Insert shaft (18) in the barrel assembly.
Illustration 14 g00625891
Illustration 15 g00666743
16. Alternate five friction disks (17) and six separator plates (16) into the travel motor housing.
Start with a separator plate and end with a separator plate.
8/15
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 16 g00626837
17. Attach Tooling (D) to the shaft. Use a suitable lifting device in order to place barrel
assembly into the travel motor body.
Note: Align the notches of the cam plate with the keys in the travel motor body before you
lower the barrel assembly into the travel motor body.
Illustration 17 g00628965
18. Use Tooling (C) to measure the depth from the top surface of the travel motor body to the
bronze face of the barrel assembly. The distance should be 38 ± 2 mm (1.5 ± 0.08 inch). If
this measurement is off, check orientation of the barrel assembly. Also check if the cam
plate is properly seated on the keys.
9/15
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. 19. Install O-ring seals (15) and the backup rings on the brake piston.
Note: Make sure that you install the backup ring and the O-ring seal in the original position.
Refer to Illustration 19.
Illustration 20 g00629015
20. Install brake piston (14) in the body of the travel motor by hand. It may be necessary to use
a soft faced hammer to seat the brake piston correctly.
Illustration 21 g00629060
21. Use Tooling (C) to measure the distance from the top of the brake piston (14) to the top
surface of the travel motor body. The distance should be 20.8 ± 1 mm (0.82 ± 0.04 inch). If
this measurement is off, drive the brake piston further into the travel motor body.
11/15
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 22 g00627391
22. Install springs (12) and plate (11) .
23. Install O-ring seals (13) .
Illustration 23 g00629646
24. Use Tooling (E) to drive the bearing into the head.
Illustration 24 g00627405
12/15
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. 25. Install O-ring seal (9) onto the head.
26. Install port plate (8) on the head. It may be necessary to apply a small amount of grease to
the port plate in order to hold the port plate in place during the installation of the head.
Illustration 25 g00629613
27. Turn over head (6). Install Tooling (F) onto the head. Use a suitable lifting device to install
the head onto the travel motor.
Illustration 26 g00631594
28. Install three dowels (7) into the head.
13/15
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 27 g00628657
29. Install an O-ring on each plug (5) .
30. Install six bolts (4) which hold the head in place. Tighten the six bolts to a torque of 530 ±
70 N·m (391 ± 52 lb ft).
31. Install plugs (5) that hold the dowels in the head. Tighten the plugs to a torque of 75 ± 7
N·m (55 ± 5 lb ft).
Illustration 28 g00624938
32. Install O-ring seals (2) and rings (3) on the displacement change valve.
14/15
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 29 g00627438
33. Install displacement change valve (1) onto the head of the travel motor. Tighten the
displacement change valve to a torque of 50 ± 3 N·m (37 ± 2 lb ft).
34. To prevent possible damage to the travel motor, the unit should be filled with oil at least up
to the fill port prior to operation. Refer to Operation and Maintenance Manual for the
correct oil specification.
End By: Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install" in
this manual.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 4 12:11:29 UTC+0800 2020
15/15
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B EXCAVATOR AMD
Configuration: ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)
Disassembly and Assembly
345B, 345B Series II and W345B Series II Excavators Machine Systems
Media Number -SENR1934-11 Publication Date -01/01/2012 Date Updated -12/01/2012
i01321681
Travel Motor - Install - Series II
SMCS - 4351-012
S/N - AGS1-UP
S/N - AKJ1-UP
S/N - AKX1-UP
S/N - ALB1-UP
S/N - ALD1-UP
S/N - AMD1-UP
S/N - AMJ1-UP
S/N - AMN1-UP
S/N - APB1-UP
S/N - AYR1-UP
S/N - CCC1-UP
S/N - DCW1-UP
S/N - DET1-UP
S/N - FEE1-UP
Installation Procedure
Table 1
1/5
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Required Tools
Tool Part Number Part Description Qty
(A) 138-7574 Link Bracket 2
(B) M20x2.5x458mm (18 inch) Threaded Rod 2
Note: The procedure to install the right hand travel motor and the procedure to install the
left hand travel motor is identical. The procedure that follows is for one of the travel motors.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
Illustration 1 g00699158
Typical example
2. Replace the O-ring seal (6) that is used between the travel motor and the final drive.
3. Install O-ring seal (6) in the final drive. Apply clean hydraulic oil on the O-ring seal.
4. Install coupling (7) .
2/5
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 2 g00594780
Typical example
5. Carefully push travel motor (5) onto Tooling (B), as shown.
Illustration 3 g00699082
6. Remove two bolts from the head of travel motor (5) in order to install Tooling (A) .
7. Reposition the hoist and two lifting straps onto Tooling (A), as shown.
8. Slide the travel motor into the final drive.
3/5
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. 9. Install bolt (4) and remove Tooling (B) .
10. Remove Tooling (A) and install the two bolts back into the head of the travel motor.
Illustration 4 g00699080
11. Install three bolts (3) that secure the travel motor to the final drive.
Illustration 5 g00633124
Typical example
12. Remove the plugs from the ends of hose assemblies (1) and (2) .
13. Connect hose assemblies (1) and (2) to the travel motor.
NOTICE
To avoid system damage, make sure that the hydraulic motor is
properly filled with hydraulic oil before start-up.
4/5
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. 14. Fill the final drive with hydraulic oil to the correct level.
Reference: Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
Reference: Refer to Operation and Maintenance Manual, "Refill Capacities" for the correct
amount.
Reference: Refer to Operation and Maintenance Manual, "Final Drive Oil Level - Check"
for the correct filling procedure.
15. Install high efficiency filters in place of the pilot filter, case drain filter, and the return filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
16. Obtain a hydraulic oil sample from the main S·O·S port.
Reference: Refer to Operation and Maintenance Manual, "Sampling Interval and Location
of Sampling Valve" for the correct location.
17. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system.
End By: Install the travel brake valve. Refer to Disassembly and Assembly, "Travel Brake Valve
- Install" in this manual.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 4 12:12:24 UTC+0800 2020
5/5
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345B EXCAVATOR AMD
Configuration: ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)
Disassembly and Assembly
345B, 345B Series II and W345B Series II Excavators Machine Systems
Media Number -SENR1934-11 Publication Date -01/01/2012 Date Updated -12/01/2012
i06299392
Final Drive and Travel Motor - Remove
SMCS - 4050-011; 4351-011
S/N - 2NW1-UP
S/N - 2SW1-UP
S/N - 2ZW1-UP
S/N - 3MW1-UP
S/N - 4SS1-UP
S/N - 5WS1-UP
S/N - 6MW1-UP
S/N - 6XS1-UP
S/N - 7KS1-UP
S/N - 8KW1-UP
S/N - 8RW1-UP
S/N - 9CW1-UP
S/N - 9GS1-UP
S/N - AGS1-UP
S/N - AKJ1-UP
S/N - AKX1-UP
1/5
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. S/N - ALB1-UP
S/N - ALD1-UP
S/N - AMD1-UP
S/N - AMJ1-UP
S/N - AMN1-UP
S/N - APB1-UP
S/N - AYR1-UP
S/N - BFG1-UP
S/N - CCC1-UP
S/N - DCW1-UP
S/N - DET1-UP
S/N - FEE1-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(A)
132-8223 Power Pack 1
1U-6221 Hydraulic Torque Wrench Assembly 1
132-8154 3/4 inch Square Drive Link 1
Start By:
A. Remove the final drive sprocket. Refer to Disassembly and Assembly, "Final Drive
Sprocket - Remove and Install" in this manual.
B. Remove the travel brake valve. Refer to Disassembly and Assembly, "Counterbalance
Valve (Travel) - Remove" in this manual.
Note: The final drive sprocket does not need to be removed prior to removal of the final drive. If
the final drive is going to be disassembled, the sprocket should be removed.
Note: The procedure to remove the right hand final drive and the procedure to remove the left
hand final drive is identical. The procedure that follows is for one of the final drives.
NOTICE
2/5
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00595681
1. Attach two lifting straps and a hoist to final drive (1) , as shown. It may be necessary to
adjust the lifting straps for correct balance of the final drive.
3/5
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
26. Illustration 2 g00633039
2. Oil will drain from the hose assembly (2) and hose assembly (3) when the hoses are
disconnected from the travel motor. Position an oil pan under the travel motor in order to
contain the hydraulic oil.
3. For assembly purposes, put identification marks on hose assembly (2) and hose assembly
(3) . Disconnect hose assembly (2) and hose assembly (3) from the travel motor. Put a plug
in the end of each hose assembly. Plugs prevent oil loss and plugs keep contaminants out of
the hydraulic system.
Illustration 3 g00594077
Illustration 4 g00633042
4. Use Tooling (A) to remove bolts (4) and the washers that hold the final drive to the
undercarriage frame assembly. Carefully remove the final drive and the travel motor from
the undercarriage frame assembly. The combined weight of the final drive and the travel
motor is 714 kg (1575 lb).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 4 12:13:19 UTC+0800 2020
4/5
ISJ HEX COMMONALITY CHART AMD00001-UP (MACHINE)(SEBP5600 - 00) -...
2020/9/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...