The document provides step-by-step instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists 32 steps for disassembly, removing components like the carrier assembly, ring gear, and bearings. It then lists 13 steps for assembly, reinstalling these components in reverse order and noting that cleanliness is important, O-rings and seals should be replaced, and anti-seize compound should be used on threads.
Caterpillar cat 345 d l excavator (prefix rgd) service repair manual (rgd0000...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists 31 steps to fully disassemble the travel motor by removing components like the head, plates, seals, pins, brake piston, disks, and housing keys. Reassembly requires reversing the disassembly steps and ensuring parts are cleaned and placed back in their original locations and orientations. Special tools are listed to aid in removal and installation of components.
Caterpillar cat 345 d l excavator (prefix rae) service repair manual (rae0000...hhfjksekmm
This document provides step-by-step instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, bearings, and housing. Precautions are given to properly support heavy parts, avoid damage, and prevent contamination. Tools required are also listed.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 938 f wheel loader (prefix 7sn) service repair manual (7sn000...hhfjksekmm
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes in detail how to separate the transmission from the torque converter using various tools. It then outlines the step-by-step process to disassemble the transmission, including removing shafts, gears, seals, plates and other components. Precautions are noted regarding weights of parts and ensuring components are properly marked for reassembly.
Caterpillar cat 345 c excavator (prefix wde) service repair manual (wde00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 28 parts in 28 steps, including removing the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure involves installing 29 parts in 29 steps in the reverse order, adjusting bearing preload using shims, and applying anti-seize compound and thread lock to ensure proper assembly. Tools such as retaining ring pliers, eyebolts, and a transmission stand are required.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar cat 345 d l excavator (prefix jkn) service repair manual (jkn0000...hhfjksekmm
The document provides instructions for assembling a travel motor. It describes 33 steps to assemble parts like pistons, seals, plates, springs and valves. Measurements are checked with tools at several steps to ensure correct assembly. Cleaning parts and preventing contamination of hydraulic systems is emphasized.
Caterpillar cat 345 d l excavator (prefix rgd) service repair manual (rgd0000...hhfjksekmm
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists 31 steps to fully disassemble the travel motor by removing components like the head, plates, seals, pins, brake piston, disks, and housing keys. Reassembly requires reversing the disassembly steps and ensuring parts are cleaned and placed back in their original locations and orientations. Special tools are listed to aid in removal and installation of components.
Caterpillar cat 345 d l excavator (prefix rae) service repair manual (rae0000...hhfjksekmm
This document provides step-by-step instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, bearings, and housing. Precautions are given to properly support heavy parts, avoid damage, and prevent contamination. Tools required are also listed.
Caterpillar cat 345 d l excavator (prefix kfh) service repair manual (kfh0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a C13 engine, including:
1. The procedure for removing the rear gear group involves removing 10 components and using 2 required tools.
2. The installation procedure involves 11 steps and uses 1 required tool, and includes instructions for properly installing and positioning bearings.
3. Separate sections provide procedures for removing and installing the flywheel and crankshaft rear seal. Precautions are mentioned regarding handling heated parts and containing fluids.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 938 f wheel loader (prefix 7sn) service repair manual (7sn000...hhfjksekmm
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes in detail how to separate the transmission from the torque converter using various tools. It then outlines the step-by-step process to disassemble the transmission, including removing shafts, gears, seals, plates and other components. Precautions are noted regarding weights of parts and ensuring components are properly marked for reassembly.
Caterpillar cat 345 c excavator (prefix wde) service repair manual (wde00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 28 parts in 28 steps, including removing the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure involves installing 29 parts in 29 steps in the reverse order, adjusting bearing preload using shims, and applying anti-seize compound and thread lock to ensure proper assembly. Tools such as retaining ring pliers, eyebolts, and a transmission stand are required.
Caterpillar cat 365 b ii excavator (prefix der) service repair manual (der000...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B II EXCAVATOR. Key steps include:
1. Disassembling the final drive by removing gears, bearings, seals and housing components using various tools.
2. Determining the correct shim thickness for reassembly by measuring gear dimensions under precise loading conditions.
3. Reassembling the components in reverse order, applying anti-seize compound and torque sealant, and ensuring proper installation of seals between housings.
Caterpillar cat 345 d l excavator (prefix jkn) service repair manual (jkn0000...hhfjksekmm
The document provides instructions for assembling a travel motor. It describes 33 steps to assemble parts like pistons, seals, plates, springs and valves. Measurements are checked with tools at several steps to ensure correct assembly. Cleaning parts and preventing contamination of hydraulic systems is emphasized.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists the required tools and presents 33 steps for disassembly, removing all internal components. It then outlines 37 steps for reassembly, starting with cleaning and inspecting parts, and continuing through installing bearings, seals, gears, and housing components in the reverse order of disassembly. Tolerances and special installation tools are specified to ensure proper bearing preload and sealing.
Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the housing cover, carrier assemblies, planetary gear assemblies, ring gear, and motor housing. Precautions are given to ensure cleanliness during disassembly and assembly. The parts are to be reinstalled in their original locations and orientation marks should be made for alignment. Proper lifting devices and techniques are specified due to the heavy weights of some components.
Caterpillar cat 345 b series ii excavator (prefix ald) service repair manual ...fjsekdmmeed
This document provides instructions for removing and installing a lifter group on a 3176C engine. The removal process involves taking out bolts and separating the lifter assembly into sections to remove individual components like brackets, lifters and injector lifters. The installation is the reverse of removal, requiring cleaning of parts and reinstallation in the proper order and orientation. Precautions are provided to contain fluids and dispose of them according to regulations.
Caterpillar cat 324 d l excavator (prefix lab) service repair manual (lab0000...jfksekmmdme
This document provides the disassembly procedure for the final drive of a 324D L Excavator. It begins by listing the required tools. The procedure then details 32 steps to fully disassemble the final drive. These steps include removing gears, shafts, seals, housings, and other components. Special tools and multiple people are required for removing some heavier parts. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms.
Caterpillar cat 325 d excavator (prefix kbe) service repair manual (kbe00001 ...hfjsekekmmd
The document provides instructions for repairing the final drive of excavator models 325D and 325D L. It involves 14 steps including cleaning parts, applying lubricants, installing seals and bearings, adjusting bearing preload, and assembling components like the carrier assembly, planetary gears, and ring gear. Proper torque values and alignment of pins are emphasized throughout the process to ensure correct assembly.
Caterpillar cat 324 d excavator (prefix mnd) service repair manual (mnd00001 ...fjskekdmmem
The document provides instructions for disassembling the final drive of a 324D excavator. It lists required tools and 33 steps to completely disassemble the final drive. Key steps include removing the cover, carrier assembly, planetary gears, sun gears, and housing components. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 365 b excavator (prefix 9tz) service repair manual (9tz00001 ...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B L excavator. It describes in detail the 31 steps to disassemble the components of the final drive, including removing gears, shafts, carriers, and housing pieces. It then lists the 34 assembly steps, specifying the required tools and explaining how to install components like bearings, seals, gears, and housings back into the final drive. Precautions like cleaning parts and applying lubricants are noted.
Caterpillar cat 324 d ln excavator (prefix sym) service repair manual (sym000...jfksekmmdme
This document provides disassembly instructions for the final drive of a 324D L and 324D LN excavator. It outlines 32 steps to fully disassemble the final drive assembly, including removing gears, shafts, housings, seals, and other internal components. Cleanliness is emphasized to prevent dirt contamination during disassembly. Various specialty tools are listed that are required to remove retaining rings, pins, and other secured pieces. The document provides illustrations and detailed instructions for each step in the disassembly process.
The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, shafts, carriers, and planetary gears. Tools needed are listed. Detailed illustrations accompany each step to show how to remove each component. Cleanliness is emphasized to prevent dirt from entering during disassembly.
Caterpillar cat 325 d l excavator (prefix nac) service repair manual (nac0000...fjsekdmmeed
This document provides repair instructions for a 325D L excavator transmission. It outlines 33 steps to disassemble and reassemble the transmission components. Key parts include the main housing, motor housing, bearings, seals, gears, carriers, plugs, and cover. The instructions emphasize cleanliness and applying anti-seize compound to parts during assembly. Precise measurements and shimming are required to set bearing preload.
Caterpillar cat 324 d l excavator (prefix tsn) service repair manual (tsn0000...jfksekmmdme
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D and 324D L. The disassembly procedure involves 28 steps to remove components from the travel motor housing, including the head, port plate, bearings, brake piston, plates, springs, and seals. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of marked components.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 14 m motor grader (prefix b9j) service repair manual (b9j0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M Motor Grader. It lists 50 steps to fully disassemble these components, including removing sprockets, gears, seals, bearings, and housings. Various tools are required, and safety precautions are provided. Detailed illustrations accompany each step to show how to position parts and which fasteners to remove. Component weights are listed to assist with lifting and handling.
Caterpillar cat 385 c l excavator (prefix eda) service repair manual (eda0000...fjkskedmme
The document provides instructions for disassembling and assembling the final drive of a 385C L excavator. Key steps include:
1. Fastening the final drive to a repair stand and marking components for reassembly.
2. Removing housing covers, gears, shafts, and planetary gear assemblies from the carrier assemblies using lifting devices and tools.
3. Separating the housing from the motor housing and removing additional components from each.
4. Reassembling the components in reverse order, applying lubricants and sealants as needed, and adjusting bearing preload during assembly. Precision, cleanliness, and proper tooling are emphasized throughout.
Caterpillar cat 312 c l excavator (prefix cbt) service repair manual (cbt0000...fksjksmmde
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in multiple steps to fully disassemble the swing drive. These parts include gears, shafts, bearings, seals, and housings. The assembly section then lists the parts and tools needed and describes the reverse process of installing the components in the proper order and applying sealants or fasteners as needed.
Caterpillar cat 345 d l excavator (prefix pbt) service repair manual (pbt0000...hhfjksekmm
This document provides disassembly and assembly instructions for the swing drive of a 345D L excavator. It details 32 steps to disassemble the swing drive components including removing the carrier assembly, sun gear, ring gear, and bearings. It also lists the required tools. The assembly section notes the importance of cleanliness and lists 13 tools needed for reassembling the swing drive components.
Caterpillar cat 345 d l excavator (prefix pbt) service repair manual (pbt0000...fjjskqazxedmmem
This document provides disassembly and assembly instructions for the swing drive of a 345D L excavator. It details 32 steps to disassemble the swing drive components including removing the carrier assembly, sun gear, ring gear, and bearings. It also lists the required tools. The assembly section notes the importance of cleanliness and lists 13 tools needed for reassembling the swing drive components.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...yinranhe0814
The document provides instructions for disassembling and assembling a swing drive. It lists the required tools and parts. The disassembly process involves removing components like the carrier assembly, ring gear, sun gear and planetary gears. The assembly process instructs to clean parts and apply lubricants before reinstalling components like bearings, seals and gears in the reverse order of disassembly. Proper alignment and pressing of components into place is emphasized.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...wfu089267
The document provides instructions for disassembling and assembling a swing drive. It lists the required tools and parts. The disassembly process involves removing components like the carrier assembly, ring gear, and bearings. The assembly process describes cleaning and preparing the parts, applying lubricants, and installing components like the bearings, seals, and carrier assembly back into the swing drive housing. Proper alignment and pressing of parts into place is emphasized.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...zatao0179249295
The document provides instructions for disassembling and assembling a swing drive. It lists the required tools and parts. The disassembly process involves removing components like the carrier assembly, ring gear, sun gear and planetary gears. The assembly process instructs to clean parts and apply lubricants before reinstalling components like bearings, seals and gears in the reverse order of disassembly. Proper alignment and pressing of components into place is emphasized.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. The disassembly process involves removing 27 parts from the final drive housing using various tools. The assembly process specifies applying anti-seize compound to bearing surfaces and installing parts in reverse order using lifting devices and a pressure tool to set the bearing preload. Proper cleaning and inspection of O-rings is also noted.
Caterpillar cat 374 d l excavator (prefix pas) service repair manual (pas0000...fjjskekdmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists the required tools and presents 33 steps for disassembly, removing all internal components. It then outlines 37 steps for reassembly, starting with cleaning and inspecting parts, and continuing through installing bearings, seals, gears, and housing components in the reverse order of disassembly. Tolerances and special installation tools are specified to ensure proper bearing preload and sealing.
Caterpillar cat 385 c l excavator (prefix sbe) service repair manual (sbe0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 385C L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the housing cover, carrier assemblies, planetary gear assemblies, ring gear, and motor housing. Precautions are given to ensure cleanliness during disassembly and assembly. The parts are to be reinstalled in their original locations and orientation marks should be made for alignment. Proper lifting devices and techniques are specified due to the heavy weights of some components.
Caterpillar cat 345 b series ii excavator (prefix ald) service repair manual ...fjsekdmmeed
This document provides instructions for removing and installing a lifter group on a 3176C engine. The removal process involves taking out bolts and separating the lifter assembly into sections to remove individual components like brackets, lifters and injector lifters. The installation is the reverse of removal, requiring cleaning of parts and reinstallation in the proper order and orientation. Precautions are provided to contain fluids and dispose of them according to regulations.
Caterpillar cat 324 d l excavator (prefix lab) service repair manual (lab0000...jfksekmmdme
This document provides the disassembly procedure for the final drive of a 324D L Excavator. It begins by listing the required tools. The procedure then details 32 steps to fully disassemble the final drive. These steps include removing gears, shafts, seals, housings, and other components. Special tools and multiple people are required for removing some heavier parts. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms.
Caterpillar cat 325 d excavator (prefix kbe) service repair manual (kbe00001 ...hfjsekekmmd
The document provides instructions for repairing the final drive of excavator models 325D and 325D L. It involves 14 steps including cleaning parts, applying lubricants, installing seals and bearings, adjusting bearing preload, and assembling components like the carrier assembly, planetary gears, and ring gear. Proper torque values and alignment of pins are emphasized throughout the process to ensure correct assembly.
Caterpillar cat 324 d excavator (prefix mnd) service repair manual (mnd00001 ...fjskekdmmem
The document provides instructions for disassembling the final drive of a 324D excavator. It lists required tools and 33 steps to completely disassemble the final drive. Key steps include removing the cover, carrier assembly, planetary gears, sun gears, and housing components. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar cat 345 d l excavator (prefix byc) service repair manual (byc0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group on a 345D L Excavator powered by a C13 engine, including:
1. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, gears, bushings, bearings, and covers.
2. Detailed installation instructions are also provided, including proper tooling, torque specifications, and ensuring correct dimensions and alignments of components.
3. Removal and installation of the flywheel and rear crankshaft seal are also described following similar procedures.
Caterpillar cat 365 b excavator (prefix 9tz) service repair manual (9tz00001 ...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of a 365B L excavator. It describes in detail the 31 steps to disassemble the components of the final drive, including removing gears, shafts, carriers, and housing pieces. It then lists the 34 assembly steps, specifying the required tools and explaining how to install components like bearings, seals, gears, and housings back into the final drive. Precautions like cleaning parts and applying lubricants are noted.
Caterpillar cat 324 d ln excavator (prefix sym) service repair manual (sym000...jfksekmmdme
This document provides disassembly instructions for the final drive of a 324D L and 324D LN excavator. It outlines 32 steps to fully disassemble the final drive assembly, including removing gears, shafts, housings, seals, and other internal components. Cleanliness is emphasized to prevent dirt contamination during disassembly. Various specialty tools are listed that are required to remove retaining rings, pins, and other secured pieces. The document provides illustrations and detailed instructions for each step in the disassembly process.
The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, shafts, carriers, and planetary gears. Tools needed are listed. Detailed illustrations accompany each step to show how to remove each component. Cleanliness is emphasized to prevent dirt from entering during disassembly.
Caterpillar cat 325 d l excavator (prefix nac) service repair manual (nac0000...fjsekdmmeed
This document provides repair instructions for a 325D L excavator transmission. It outlines 33 steps to disassemble and reassemble the transmission components. Key parts include the main housing, motor housing, bearings, seals, gears, carriers, plugs, and cover. The instructions emphasize cleanliness and applying anti-seize compound to parts during assembly. Precise measurements and shimming are required to set bearing preload.
Caterpillar cat 324 d l excavator (prefix tsn) service repair manual (tsn0000...jfksekmmdme
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D and 324D L. The disassembly procedure involves 28 steps to remove components from the travel motor housing, including the head, port plate, bearings, brake piston, plates, springs, and seals. The assembly procedure reverses the disassembly steps and involves installing components in the proper order and orientation, with notes to clean parts thoroughly, apply lubricant, and ensure correct positioning of marked components.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 14 m motor grader (prefix b9j) service repair manual (b9j0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 14M Motor Grader. It lists 50 steps to fully disassemble these components, including removing sprockets, gears, seals, bearings, and housings. Various tools are required, and safety precautions are provided. Detailed illustrations accompany each step to show how to position parts and which fasteners to remove. Component weights are listed to assist with lifting and handling.
Caterpillar cat 385 c l excavator (prefix eda) service repair manual (eda0000...fjkskedmme
The document provides instructions for disassembling and assembling the final drive of a 385C L excavator. Key steps include:
1. Fastening the final drive to a repair stand and marking components for reassembly.
2. Removing housing covers, gears, shafts, and planetary gear assemblies from the carrier assemblies using lifting devices and tools.
3. Separating the housing from the motor housing and removing additional components from each.
4. Reassembling the components in reverse order, applying lubricants and sealants as needed, and adjusting bearing preload during assembly. Precision, cleanliness, and proper tooling are emphasized throughout.
Caterpillar cat 312 c l excavator (prefix cbt) service repair manual (cbt0000...fksjksmmde
The document provides instructions for disassembling and assembling the swing drive of a 312C excavator. It describes removing over 20 individual parts in multiple steps to fully disassemble the swing drive. These parts include gears, shafts, bearings, seals, and housings. The assembly section then lists the parts and tools needed and describes the reverse process of installing the components in the proper order and applying sealants or fasteners as needed.
Caterpillar cat 345 d l excavator (prefix pbt) service repair manual (pbt0000...hhfjksekmm
This document provides disassembly and assembly instructions for the swing drive of a 345D L excavator. It details 32 steps to disassemble the swing drive components including removing the carrier assembly, sun gear, ring gear, and bearings. It also lists the required tools. The assembly section notes the importance of cleanliness and lists 13 tools needed for reassembling the swing drive components.
Caterpillar cat 345 d l excavator (prefix pbt) service repair manual (pbt0000...fjjskqazxedmmem
This document provides disassembly and assembly instructions for the swing drive of a 345D L excavator. It details 32 steps to disassemble the swing drive components including removing the carrier assembly, sun gear, ring gear, and bearings. It also lists the required tools. The assembly section notes the importance of cleanliness and lists 13 tools needed for reassembling the swing drive components.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...yinranhe0814
The document provides instructions for disassembling and assembling a swing drive. It lists the required tools and parts. The disassembly process involves removing components like the carrier assembly, ring gear, sun gear and planetary gears. The assembly process instructs to clean parts and apply lubricants before reinstalling components like bearings, seals and gears in the reverse order of disassembly. Proper alignment and pressing of components into place is emphasized.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...wfu089267
The document provides instructions for disassembling and assembling a swing drive. It lists the required tools and parts. The disassembly process involves removing components like the carrier assembly, ring gear, and bearings. The assembly process describes cleaning and preparing the parts, applying lubricants, and installing components like the bearings, seals, and carrier assembly back into the swing drive housing. Proper alignment and pressing of parts into place is emphasized.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...zatao0179249295
The document provides instructions for disassembling and assembling a swing drive. It lists the required tools and parts. The disassembly process involves removing components like the carrier assembly, ring gear, sun gear and planetary gears. The assembly process instructs to clean parts and apply lubricants before reinstalling components like bearings, seals and gears in the reverse order of disassembly. Proper alignment and pressing of components into place is emphasized.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. The disassembly process involves removing 27 parts from the final drive housing using various tools. The assembly process specifies applying anti-seize compound to bearing surfaces and installing parts in reverse order using lifting devices and a pressure tool to set the bearing preload. Proper cleaning and inspection of O-rings is also noted.
Caterpillar Cat 385B L Excavator (Prefix FDL) Service Repair Manual (FDL00001...jdjkskmikdkmd
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
Caterpillar Cat 385B L Excavator (Prefix FDL) Service Repair Manual (FDL00001...paws21610697
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly process involves removing 27 parts from the final drive housing including gears, shafts, bearings, seals and housings. Individual components are removed using various tools including hydraulic wrenches, sockets and lifting devices.
The assembly process reverses the disassembly steps. It instructs applying anti-seize compound to bearing surfaces, setting proper bearing preload using shims, and installing seals and housings. Special tools are required to install some components. Proper cleaning and inspection of parts is emphasized throughout.
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
Caterpillar cat 385 b l excavator (prefix fdl) service repair manual (fdl0000...f9iosoidd
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. The disassembly process involves removing 27 parts from the final drive housing using various tools. The assembly process specifies applying anti-seize compound to bearing surfaces and installing parts in reverse order using lifting devices and a pressure tool to set the bearing preload. Proper cleaning and inspection of O-rings is also noted.
Caterpillar cat 385 b excavator (prefix fdl) service repair manual (fdl00001 ...fios9dkksd
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for tasks like removing and installing gears and seals.
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
Caterpillar Cat 385B L Excavator (Prefix FDL) Service Repair Manual (FDL00001...uddksemd8ud
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for some removal and installation steps.
Caterpillar Cat 385B L Excavator (Prefix FDL) Service Repair Manual (FDL00001...f7djidksmd3e
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly process involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly process reverses this, requiring installation of shims and seals in the proper locations and applying the correct bearing preload using hydraulic pressure tools. Precise cleaning and application of anti-seize compound is important throughout the process.
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for some removal and installation steps.
Caterpillar Cat 385B and 385B L Excavator (Prefix FDL) Service Repair Manual ...yan77xunhao
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
This document provides instructions for disassembling and assembling the final drive of a 385B excavator. The disassembly process involves removing 27 parts from the final drive housing using various tools. The assembly process specifies applying anti-seize compound to bearing surfaces and installing components in reverse order using lifting devices and a pressure tool to set the bearing preload. Proper cleaning and inspection of seals is emphasized before reassembly.
Caterpillar Cat 385B L Excavator (Prefix FDL) Service Repair Manual (FDL00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly procedure involves removing 27 parts in a specific sequence, including removing the ring gear, carrier assemblies, gears, shafts and seals. The assembly procedure instructs installing 31 parts in reverse order, and describes determining the correct shim thickness between the bearing cone and coupling gear to achieve proper bearing preload. Special tools are required for several steps.
Caterpillar cat 349 f l excavator (prefix hlb) service repair manual (hlb0000...didkskdkmdm
1. The document provides disassembly and assembly instructions for the travel motor on 349F and 349F L excavators.
2. It describes 31 steps to disassemble the travel motor, removing components like plugs, springs, pistons, and bearings. Special tools and precautions are noted.
3. The assembly section lists 15 specifications for components like plug torque values, seal types, and spring dimensions to follow when reassembling the travel motor. Proper lubrication of parts is emphasized.
Caterpillar cat 349 f excavator (prefix hlb) service repair manual (hlb00001 ...cdsaas
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Similar to Caterpillar cat 345 d l excavator (prefix pbt) service repair manual (pbt00001 and up) (20)
Komatsu saa6 d125 2 diesel engine service repair manualifkkdkmdmd
The document provides instructions for the reader to click on a link to access a complete manual without waiting. It notes that if clicking the link does not work, the reader should first download the PDF document and then click on it to access the manual.
This document is a shop manual for a Komatsu PC3000-6 hydraulic mining shovel with serial number PC3000-6 6219. It contains instructions for maintenance and repair of major components. The manual begins with safety warnings and tables of contents. It then provides specifications and overview descriptions of the shovel's main assembly groups and systems, including the drive system, hydraulic oil reservoir, and other components. Technicians are instructed to follow the manual's guidelines for personal and operational safety.
This shop manual provides proprietary information for maintaining and repairing the Komatsu Mining Germany GmbH PC3000-1 hydraulic mining shovel with serial number PC3000-1 6225. The manual is subject to revisions as the company continuously works to improve its products. Customers are advised to check with their distributor for the latest version of the manual. The manual is copyrighted and not to be reproduced without authorization from Komatsu Mining Germany GmbH.
This document is a shop manual for the PC3000-1 hydraulic mining shovel with serial number PC3000-1 6194. It provides information on the assembly, components, and systems of the mining shovel, including the main assembly groups, drive, hydraulic oil tank, hydraulic oil cooling, controls, and electronic monitoring system. The manual is proprietary to Komatsu Mining Germany GmbH and is subject to revisions as the company continues its research and development. Customers are advised to contact their distributor for the latest revision.
This 3-sentence summary provides the key details from the document:
The document is a shop manual for a Komatsu Mining Germany hydraulic mining shovel with serial number PC3000-1 6182, noting that the manual contains proprietary information and revisions may be made due to Komatsu's continuous research and development efforts. The manual was printed in the U.S.A. in July 2006 by Komatsu Mining Germany.
This 3-sentence summary provides the key details from the document:
The document is a shop manual for a Komatsu Mining Germany hydraulic mining shovel with serial number PC3000-1 6174, which contains proprietary information not to be reproduced without authorization. The manual notifies readers that Komatsu's policy is to improve products whenever possible, and revisions may be made to the publication, so customers should contact their distributor for the latest information. It was printed in the U.S.A. in July 2006 by Komatsu Mining Germany.
This 3-sentence summary provides the key details from the document:
The document is an operation and maintenance manual for a Komatsu Mining Germany GmbH hydraulic mining shovel with serial number PC3000-1 6193, with information that is proprietary and not to be reproduced without authorization. The manual was printed in July 2006 and Komatsu Mining Germany reserves the right to make changes or improvements to their products without updating previously sold models, as their research and development results in regular revisions to publications. Customers are advised to contact their distributor for information on the latest revision of the manual.
This document is the operation and maintenance manual for a Komatsu PC2000-8 hydraulic excavator. It provides important safety information and instructions for operating and servicing the excavator. Operators and maintenance personnel must read this manual thoroughly before working on the machine to understand safety precautions and procedures. The manual includes sections on safety, machine operation, controls and gauges, monitoring systems, and emergency procedures.
Massey ferguson mf 135148 mkiii135145 vs tractors (fr) parts catalogue manualifkkdkmdmd
This document contains parts lists and descriptions for engines and components of Massey Ferguson 135/148 MKIII/135/145 V/S tractors. It includes lists of parts for the engine and accessories for two different time periods, as well as parts lists for the cylinder block, crankshaft, pistons, connecting rods, and cylinder head of the AD3.152 engine. Each part is accompanied by the part number, quantity used, a description, and sometimes additional comments.
Massey ferguson mf 133135 mkiii135 v tractors parts catalogue manualifkkdkmdmd
The document provides a parts list for Massey Ferguson MF 133/135 MKIII/135 V tractors. It includes 37 items with part numbers, quantities, descriptions, and comments. The parts are grouped into sections including the engine and accessories, cylinder block, crankshaft, pistons, connecting rods, and cylinder head. The list provides replacement part numbers and notes differences for parts based on serial number and engine details.
Massey ferguson mf 7278 cerea combines parts catalogue manualifkkdkmdmd
The document provides a parts list and descriptions for the knives and fingers, right hand table auger, and left hand table auger components of Massey Ferguson MF 7272/7274/7278 CEREA combines for 20-22 foot headers. It lists over 150 individual part numbers, quantities, and additional identifying information for each component. Key parts include blades, fingers, bearings, plates, shafts, arms, and covers for the cutting and conveying mechanisms. Serial numbers are specified for some parts to indicate application ranges.
Massey ferguson mf 7276 combine parts catalogue manualifkkdkmdmd
1. The document provides a list of parts for the knives and fingers and table auger assemblies for Massey Ferguson MF 7274/7276 combines for various header widths ranging from 16 to 22 feet.
2. It includes the part numbers, quantities, descriptions, and any relevant comments for 142 total parts across both assemblies.
3. The parts are organized into tables with the item number, part number, quantity, description, and any applicable comments or footnotes provided for each part.
Massey ferguson mf 7274 combine parts catalogue manualifkkdkmdmd
1. The document provides a list of parts for the knives and fingers and table auger assemblies for Massey Ferguson MF 7274/7276 combines for various header widths ranging from 16 to 22 feet.
2. It includes the part numbers, quantities, descriptions, and any relevant comments for 142 different parts across both assemblies.
3. The parts are organized into tables with the item number, part number, quantity, description, and any applicable comments or footnotes provided for each part.
Massey ferguson mf 7274 cerea combines parts catalogue manualifkkdkmdmd
The document provides a parts list and descriptions for the knives and fingers, right hand table auger, and left hand table auger components of Massey Ferguson MF 7272/7274/7278 CEREA combines for 20-22 foot headers. It lists over 150 individual part numbers, quantities, and additional identifying information for each component. Key parts include blades, fingers, bearings, plates, shafts, arms, and covers for the cutting and conveying mechanisms. Serial numbers are specified for some parts to indicate application ranges.
Massey ferguson mf 7272 combine parts catalogue manualifkkdkmdmd
This document provides a parts list for a Massey Ferguson MF 7272 combine. It includes over 140 individual parts grouped into items numbered 1 through 142. Each item lists the part number, quantity, description, and any relevant comments. The parts are for the knives and fingers, table augers, and other components of the combine header for models ranging from 16 to 20 feet in width. Footnotes provide additional information about specific parts.
Massey ferguson mf 7272 cerea combines parts catalogue manualifkkdkmdmd
The document provides a parts list and descriptions for the knives and fingers, right hand table auger, and left hand table auger components of Massey Ferguson MF 7272/7274/7278 CEREA combines. It includes over 150 individual part numbers, quantities, and additional identifying information for components across the different sections. Key parts listed include blades, fingers, bearings, plates, shafts, arms, and fasteners for the cutting and conveying mechanisms. Serial numbers are specified for some part applicability.
Massey ferguson mf 7256 combine parts catalogue manualifkkdkmdmd
This document provides a parts list for the knives and fingers and table auger components for a Massey Ferguson MF 7254/7256 combine harvester. It includes 142 numbered items with corresponding part numbers and descriptions. Footnotes provide additional part number options and application details for some components. The parts listed are for freeflow headers ranging from 14 to 20 feet in width.
Massey ferguson mf 7256 cerea combine parts catalogue manualifkkdkmdmd
This document provides a list of parts for the table auger and knives for a Massey Ferguson MF 7256 CEREA COMBINE. It includes over 140 individual part numbers, descriptions, and specifications for components ranging from clips and bolts to the entire table auger assembly. The parts are organized by item number and apply to various configurations for header widths ranging from 14 to 20 feet. Footnotes provide additional information on part applicability.
Massey ferguson mf 7254 combine parts catalogue manualifkkdkmdmd
This document provides a parts list for the knives and fingers and table auger components for a Massey Ferguson MF 7254/7256 combine harvester. It includes 142 numbered items with corresponding part numbers and descriptions. Footnotes provide additional part number options and application details for some components. The parts listed are for freeflow headers ranging from 14 to 20 feet in width.
Massey ferguson mf 7252 combine parts catalogue manualifkkdkmdmd
The document provides a list of parts for the knives and fingers and table auger assemblies for a Massey Ferguson MF 7250/7252 combine. It includes 142 line items specifying the part numbers, quantities, descriptions and additional comments for each component. The assemblies cover header widths ranging from 14' to 20'.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345D L EXCAVATOR PBT
Configuration: 345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile
Hydraulic Power Units Machine Systems
Media Number -RENR9574-10 Publication Date -01/08/2014 Date Updated -18/09/2018
i05872085
Swing Drive - Disassemble
SMCS - 5459-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B 1P-2420 Transmission Repair Stand 1
C
5P-5197 Retaining Ring Pliers 1
1U-8759 Tip Set 1
D 1P-0510 Drive Group 1
Start By:
A. Remove the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Remove and
Install".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/12
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00724836
1. Fasten Tooling (A) and a suitable lifting device to the swing drive.
2. Place the swing drive onto Tooling (B) . The weight of the swing drive is approximately
290 kg (640 lb).
3. Open the drain valve and drain the oil from the swing drive into a suitable container for
storage or disposal. The capacity of the swing drive is 11 L (2.9 US gal). If necessary,
remove the drain valve from the swing drive housing.
Illustration 2 g00724832
4. Remove oil level gauge (Dipstick) (1) , filler breather cap assembly, and hose assembly (2)
from the swing drive.
2/12
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00724843
5. Remove fitting (3) from cover (5) .
6. Remove bolts (4) and the washers from cover (5) .
Illustration 4 g00724840
7. Attach Tooling (A) to cover (5) . Remove cover (5) .
3/12
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g00724854
8. Remove sun gear (6) from the carrier assembly (7) .
Illustration 6 g00724856
9. Remove spacer (8) from carrier assembly (7) .
10. Remove carrier assembly (7) from the swing drive.
11. Disassemble carrier assembly (7) , as follows:
Illustration 7 g00724860
a. Use a hammer and a punch in order to drive spring pin (9) into planetary shaft (10) .
4/12
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g00724862
b. Remove planetary shaft (10) , thrust washer (11) , thrust washer (14) , and planetary
gear (12) from the carrier assembly.
c. Remove bearing (13) from planetary gear (12) .
d. Use a hammer and a punch in order to remove spring pin (9) from the planetary shaft
(10) .
e. Repeat Steps 11.a through 11.d in order to remove the other planetary gears from the
carrier assembly.
Illustration 9 g00724866
12. Use a screwdriver in order to remove upper retaining ring (15) from sun gear (16) .
13. Remove carrier assembly (7) from sun gear (17) .
5/12
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g00725145
14. Remove retaining ring (17) from the sun gear.
Illustration 11 g00725166
15. Attach Tooling (A) to ring gear (18) .
16. Remove ring gear (18) from the swing drive housing (19) . The weight of ring gear (18) is
approximately 36 kg (80 lb).
6/12
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g00725186
17. Remove spacer (20) from carrier assembly (21) .
Illustration 13 g00725194
18. Use two screwdrivers in order to remove retaining ring (22) .
Illustration 14 g00725203
19. Use two persons to remove carrier assembly (21) . The weight of carrier assembly (21) is
approximately 40 kg (88 lb).
20. Disassemble carrier assembly (21) , as follows:
7/12
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00725252
a. Use a hammer and a punch to drive spring pin (23) into planetary shaft (24) .
Illustration 16 g00725260
b. Remove planetary shaft (24) , thrust washer (25) , thrust washer (29) , and planetary
gear (27) from the carrier assembly.
c. Remove bearing (26) and (28) from planetary gear (27) .
d. Use a hammer and a punch to remove spring pin (23) from planetary shaft (24) .
e. Repeat Steps 20.a through 20.d in order to remove the other planetary gears from the
carrier assembly.
8/12
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 17 g00725270
21. Use Tooling (C) to remove retaining ring (30) .
Illustration 18 g01203395
Illustration 19 g03704925
22. Place swing drive housing (19) sideways. Remove bolts (32) and the washers from bearing
cage (31) .
9/12
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 23. Put swing drive housing (19) into a suitable press. The combined weight of swing drive
housing (19) , pinion shaft (33) (not shown), and bearing cage (31) (not shown) is
approximately 152 kg (335 lb).
24. Place suitable blocking under pinion shaft (33) (not shown). This will prevent the pinion
shaft from falling while the shaft is pressed out of the swing drive housing.
25. Push the pinion shaft from swing drive housing (19) .
26. Remove swing drive housing (19) and the pinion shaft from the suitable press. The weight
of swing drive housing (19) is approximately 111 kg (245 lb). The weight of pinion shaft
(33) is approximately 41 kg (90 lb).
Illustration 20 g00725386
27. Place swing drive housing (19) sideways.
28. Remove bearing cage (31) from the swing drive housing (19) .
Illustration 21 g00725388
29. Remove lip seals (34) from bearing cage (31) .
30. Remove O-ring seal (35) from bearing cage (31) .
10/12
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 22 g00725300
31. Remove bearing inner race (36) from the smaller bearing.
Illustration 23 g00725383
32. Use the following procedure to remove bearing assembly (37) , spacer (38) , and bearing
assembly (39) .
11/12
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 24 g00725391
a. Place the bearings and the swing drive housing in a suitable press.
b. Use Tooling (D) and spacer (38) in order to remove bearing assembly (39) from the
swing drive housing. The weight of swing drive housing (19) is approximately 73 kg
(160 lb).
Note: Use care when components are pushed from the swing drive housing. Avoid
injury to personnel. Also, avoid damage to components.
Note: Bearing assembly (39) will be damaged upon the removal.
Illustration 25 g00725394
c. Rotate the swing drive housing to the other side. Remove bearing assembly (37) from
swing drive housing (19) .
Note: Push the outer race in order to prevent damage to bearing assembly (37) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 25 17:00:59 UTC+0800 2020
12/12
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345D L EXCAVATOR PBT
Configuration: 345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile
Hydraulic Power Units Machine Systems
Media Number -RENR9574-10 Publication Date -01/08/2014 Date Updated -18/09/2018
i02406626
Swing Drive - Assemble
SMCS - 5459-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 2
B 1P-2420 Transmission Repair Stand 1
C
5P-5197 Retaining ring pliers 1
1U-8759 Tip Set 1
D 1P-0510 Drive Group 1
E 1U-6396 O-Ring Assembly Compound 1
F 5P-3931 Anti-Seize Compound 1
G 5P-0960 Grease Cartridge 1
H 9S-3263 Thread Lock Compound 1
J 1U-8846 Gasket Sealant 1
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
1/13
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. Use Tooling (E) during the assembly procedure.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Make sure that all parts of the swing drive are thoroughly clean and free of dirt and debris
prior to assembly.
Illustration 1 g00725394
2. ApplyTooling (F) on the outside diameter of bearing (37) and the inside diameter of swing
drive housing (19).
3. Lower the temperature of bearing (37). Install bearing (37) in the swing drive housing. It
may be necessary to use a hammer and a punch to properly seat the bearing in the swing
drive housing.
2/13
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 2 g00725388
4. Install O-ring seal (35) into bearing cage (31).
5. Install lip seals (34) in bearing cage (31).
6. ApplyTooling (G) on the lip of each seal.
Illustration 3 g00725547
7. Carefully install cage (31) over pinion shaft (33).
Illustration 4 g00725554
8. Raise the temperature of bearing (39) and install bearing (39) on pinion shaft (33).
3/13
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 5 g00725572
9. Install spacer (38) on top of bearing assembly (37), as shown.
Note: Lip (e) for spacer (38) must face opposite bearing assembly (37), as shown.
Illustration 6 g00725575
10. Put swing drive housing (19) in a suitable press.
11. Apply Tooling (F) on the outside diameter of bearing assembly (39) and the inside diameter
of the swing drive housing.
12. Install pinion shaft (33), bearing cage (31), bearing assembly (39), through spacer (38) and
bearing (37).
Note: It may be necessary to reposition the press so that bearing assembly (39) is installed
evenly into the swing drive housing.
Note: Align bearing cage (31) with the swing drive housing during installation of the pinion
shaft. Temporarily install bolts that will hold bearing cage (31) to the swing drive housing.
4/13
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 7 g00725595
13. Remove the swing drive from a suitable press and place the swing drive sideways. The
combined weight of the swing drive housing, the pinion shaft, and the bearing cage is
approximately 152 kg (335 lb).
14. Remove the temporary bolts that are holding the bearing cage in position.
15. ApplyTooling (H) on the threads of bolts (32) that hold bearing cage (31) to swing drive
housing (19).
16. Tighten bolts (32) to a torque of 100 ± 20 N·m (75 ± 15 lb ft).
Illustration 8 g00725607
17. Raise the temperature of bearing inner race (36) and install bearing inner race (36) on the
pinion shaft (33).
Note: Make sure that the shaft is centered in the swing drive housing, before you install
bearing inner race (36).
5/13
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 9 g00725270
18. Use Tooling (C) to install retaining ring (30).
19. Assemble the carrier assembly (21), as follows:
Illustration 10 g00725260
a. Apply clean SAE 30W oil on bearing (26) and bearing (28). Install bearings (26) and
(28) into planetary gear (27).
b. Install thrust washer (25) on one side of planetary gear (27).
c. Install thrust washer (29) on the other side of planetary gear (27).
d. Use a deburring tool in order to remove the metal burr from the openings in the
carrier.
e. Install planetary gear (27) and the thrust washers in the carrier assembly (21).
6/13
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 11 g00725252
f. Install planetary shaft (24) through the gear assembly into the carrier assembly. Make
sure that the spring pin hole in the planetary shaft is in alignment with the spring pin
hole in the carrier.
Illustration 12 g00703700
g. Drive spring pin (23) into planetary shaft (24). Orient the split in spring pin (23)
vertically to the carrier. Align the split in the spring pin to the top or to the bottom.
Make a stake mark on each side of the spring pin hole in the carrier. Each stake mark
should be approximately 2.25 ± 0.75 mm (0.090 ± 0.030 inch) from the outside
diameter of the spring pin hole.
h. Repeat Steps 19.a through 19.g in order to install the other three planetary gears (27)
in the carrier assembly.
7/13
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 13 g00725203
20. Use two persons and install carrier assembly (21) into the housing. The weight of carrier
assembly (21) is approximately 40 kg (88 lb).
Illustration 14 g00725194
21. Install retaining ring (22).
Illustration 15 g00725186
22. Install spacer (20) into carrier assembly (21).
8/13
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 16 g00725166
23. Make sure that the mating surfaces of ring gear (18) and swing drive housing (19) are
thoroughly clean.
24. Apply Tooling (J) to the face of swing drive housing (19) and the face of ring gear (18).
25. Install Tooling (A) onto ring gear (18). The weight of ring gear (18) is approximately 36 kg
(80 lb).
26. Install ring gear (18) onto the swing drive housing (19).
Illustration 17 g00725145
27. Install retaining ring (17) into the sun gear.
9/13
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 18 g00724866
28. Install carrier assembly (7) into the sun gear. Install retaining ring (15) into sun gear (16).
29. Assemble carrier assembly (7), as follows:
Illustration 19 g00724862
a. Apply clean SAE 30W oil on bearing (13). Install bearing (13) in planetary gear (12).
b. Install a thrust washer (11) on one side of planetary gear (12).
c. Install a thrust washer (14) on the other side of planetary gear (12).
d. Use a deburring tool in order to remove the metal burr from the openings in the
carrier.
e. Install planetary gear (12) and the thrust washers in the carrier assembly (7).
Illustration 20 g00724860
f. Install planetary shaft (10) through the gear assembly into the carrier assembly. Make
sure that the spring pin hole in the planetary shaft is in alignment with the spring pin
hole in the carrier.
10/13
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 21 g00703700
g. Drive spring pin (9) into planetary shaft (10). Orient the split in spring pin (9)
vertically to the carrier. Align the split in the spring pin to the top or to the bottom.
Make a stake mark on each side of the spring pin hole in the carrier. Each stake mark
should be approximately 2.25 ± 0.75 mm (0.09 ± 0.03 inch) from the outside diameter
of the spring pin hole.
h. Repeat Steps 29.a through 29.g for the remaining gear assemblies.
Illustration 22 g00724856
30. Install carrier assembly (7) in the ring gear.
31. Install spacer (8) into carrier assembly (7).
11/13
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 23 g00724854
32. Install sun gear (6) into carrier assembly (7).
Illustration 24 g00724840
33. Make sure that the mating surfaces of the ring gear and cover (5) are thoroughly clean.
34. Apply on the flange surface of the ring gear and cover (5).
35. Fasten Tooling (A) and a suitable lifting device to cover (5). Put the cover in the original
position on the ring gear. Make sure that the cover is seated properly.
Illustration 25 g00724843
12/13
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 36. ApplyTooling (H) on the threads of bolts (4).
37. Install the washers and bolts (4) that hold the cover, the ring gear, and the swing drive
housing together. Tighten bolts (4) to a torque of 270 ± 40 N·m (200 ± 30 lb ft).
38. Install fitting (3) into cover (5).
Illustration 26 g00724832
39. Install oil level gauge (Dipstick) (1), filler breather cap assembly, and hose assembly (2) to
the swing drive.
40. If the drain valve was removed from the swing drive housing, reinstall the drain valve.
End By:
a. Install the swing drive. Refer to Disassembly and Assembly, "Swing Drive - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 25 17:01:56 UTC+0800 2020
13/13
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEB...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345D L EXCAVATOR PBT
Configuration: 345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile
Hydraulic Power Units Machine Systems
Media Number -RENR9574-10 Publication Date -01/08/2014 Date Updated -18/09/2018
i07188254
Swing Drive - Install
SMCS - 5459-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3939 Link Bracket As 2
C 5P-3931 Anti-Seize Compound -
D 1U-8846 Gasket Sealant -
E - Loctite 243 -
1/3
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
29. Illustration 1 g01196905
Note: During the installation procedure, the locating pin for the swing drive may come out
of the swing drive housing.
1. Thoroughly clean the mating surfaces of swing drive (2) and the main frame. Apply Tooling
(C) to the pin that locates swing drive (2) in the main frame. Apply Tooling (D) to the
mating surfaces of swing drive (2) and the main frame.
2. Attach Tooling (A) and a suitable lifting device onto swing drive (2). The weight of swing
drive (2) is approximately 290 kg (640 lb). Position swing drive (2) onto the locating pin on
the main frame.
3. Install corks (3). Remove Tooling (A).
Illustration 2 g01196904
2/3
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. 4. Apply Tooling (E) to the threads of bolts (1). Install bolts (1). Tighten bolts (1) to a torque
of 250 ± 25 N·m (184 ± 18 lb ft). Turn an additional angle of 45 ± 5 degrees.
5. Refer to Service Magazine , M0083843 , "An Improved Bolt Tightening Procedure for the
Critical Joints Is Now Used on all Excavators" for more detailed information.
6. Fill the swing motor with oil. Refer to Operation and Maintenance Manual, "Swing Drive
Oil - Change".
End By:
a. Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 25 17:02:54 UTC+0800 2020
3/3
345D L Excavators PBT00001-UP (MACHINE) POWERED BY C13 Engine(SEBP5...
2020/6/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...