The document provides step-by-step instructions for disassembling the final drive of a 345C excavator. It lists 30 steps to remove components like the final drive cover, ring gear, carrier assemblies, planetary gears, and more. Detailed illustrations accompany each step to show how to attach lifting devices and tools, locate identification marks, and disassemble the various parts. Required tools include a transmission stand, link brackets, retaining ring pliers, eyebolts, and seal installer.
Caterpillar cat 345 c l hydraulic excavator (prefix gcl) service repair manua...hhfjksekmm
The document provides step-by-step instructions for disassembling the final drive of a 345C excavator. It begins by having the reader remove the final drive and coupling. They are then instructed to disassemble the multiple internal components of the final drive including the carrier assemblies, planetary gears, and sprocket housing. Detailed illustrations accompany each step to show how to remove over 30 individual parts like retainers, shafts, seals and gears from the final drive.
Caterpillar cat 345 c l hydraulic excavator (prefix els) service repair manua...hhfjksekmm
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. It describes in detail how to disassemble the various components of the final drive, including removing the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. It then describes the assembly process and how to properly adjust the bearing preload using shims. The goal is to thoroughly clean all parts and check seals before reassembling the final drive with the proper bearing adjustment.
Caterpillar cat 345 c l hydraulic excavator (prefix fpc) service repair manua...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 345C L Hydraulic Excavator. The disassembly procedure involves removing 28 parts in sequential order, including the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure similarly involves installing these 28 parts in reverse order, and adjusting the bearing preload by determining the correct number and thickness of shims to install based on precise measurement of gaps using tools like a micrometer. Proper cleaning, application of lubricants, and torque specifications are required.
Caterpillar cat 345 c excavator (prefix wde) service repair manual (wde00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 28 parts in 28 steps, including removing the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure involves installing 29 parts in 29 steps in the reverse order, adjusting bearing preload using shims, and applying anti-seize compound and thread lock to ensure proper assembly. Tools such as retaining ring pliers, eyebolts, and a transmission stand are required.
Caterpillar cat 345 c l hydraulic excavator (prefix lys) service repair manua...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly procedure involves removing over 20 individual parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs to clean all parts, apply anti-seize compound, install bearing cups and cones, and adjust shims to achieve the proper bearing preload when reassembling the components. Precise positioning of identification marks and alignment of parts is important for correct reassembly.
Caterpillar cat 345 c l excavator (prefix s5m) service repair manual (s5m0000...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly procedure involves removing over 20 components of the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs to clean all parts, apply anti-seize compound, install bearing cups and cones, and adjust the bearing preload using shims to achieve the proper load. Precise positioning of identification marks is required to reinstall parts in their original locations.
Caterpillar cat 345 c excavator (prefix taj) service repair manual (taj00001 ...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are provided for correctly reassembling the final drive.
Caterpillar cat 345 d excavator (prefix neg) service repair manual (neg00001 ...fjjskekdmme
This document provides disassembly and assembly instructions for the final drive of a 345D excavator. It details 30 steps to disassemble the final drive components including removing the cover, carrier assemblies, ring gear, and other internal parts. It then lists 21 steps for reassembling the final drive, including pressing in bearing cups, installing bearing cones and inner races, and refitting the sprocket housing and other components. Tools required are also listed.
Caterpillar cat 345 c l hydraulic excavator (prefix gcl) service repair manua...hhfjksekmm
The document provides step-by-step instructions for disassembling the final drive of a 345C excavator. It begins by having the reader remove the final drive and coupling. They are then instructed to disassemble the multiple internal components of the final drive including the carrier assemblies, planetary gears, and sprocket housing. Detailed illustrations accompany each step to show how to remove over 30 individual parts like retainers, shafts, seals and gears from the final drive.
Caterpillar cat 345 c l hydraulic excavator (prefix els) service repair manua...hhfjksekmm
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. It describes in detail how to disassemble the various components of the final drive, including removing the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. It then describes the assembly process and how to properly adjust the bearing preload using shims. The goal is to thoroughly clean all parts and check seals before reassembling the final drive with the proper bearing adjustment.
Caterpillar cat 345 c l hydraulic excavator (prefix fpc) service repair manua...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 345C L Hydraulic Excavator. The disassembly procedure involves removing 28 parts in sequential order, including the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure similarly involves installing these 28 parts in reverse order, and adjusting the bearing preload by determining the correct number and thickness of shims to install based on precise measurement of gaps using tools like a micrometer. Proper cleaning, application of lubricants, and torque specifications are required.
Caterpillar cat 345 c excavator (prefix wde) service repair manual (wde00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 28 parts in 28 steps, including removing the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure involves installing 29 parts in 29 steps in the reverse order, adjusting bearing preload using shims, and applying anti-seize compound and thread lock to ensure proper assembly. Tools such as retaining ring pliers, eyebolts, and a transmission stand are required.
Caterpillar cat 345 c l hydraulic excavator (prefix lys) service repair manua...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly procedure involves removing over 20 individual parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs to clean all parts, apply anti-seize compound, install bearing cups and cones, and adjust shims to achieve the proper bearing preload when reassembling the components. Precise positioning of identification marks and alignment of parts is important for correct reassembly.
Caterpillar cat 345 c l excavator (prefix s5m) service repair manual (s5m0000...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly procedure involves removing over 20 components of the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs to clean all parts, apply anti-seize compound, install bearing cups and cones, and adjust the bearing preload using shims to achieve the proper load. Precise positioning of identification marks is required to reinstall parts in their original locations.
Caterpillar cat 345 c excavator (prefix taj) service repair manual (taj00001 ...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing over 15 parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs how to install new seals, bearing cups and cones, shims, and other parts in the reverse order of disassembly while ensuring proper bearing preload. Tools and torque specifications are provided for correctly reassembling the final drive.
Caterpillar cat 345 d excavator (prefix neg) service repair manual (neg00001 ...fjjskekdmme
This document provides disassembly and assembly instructions for the final drive of a 345D excavator. It details 30 steps to disassemble the final drive components including removing the cover, carrier assemblies, ring gear, and other internal parts. It then lists 21 steps for reassembling the final drive, including pressing in bearing cups, installing bearing cones and inner races, and refitting the sprocket housing and other components. Tools required are also listed.
Caterpillar cat 345 c l hydraulic excavator (prefix gcl) service repair manua...fjjskqazxedmmem
The document provides step-by-step instructions for disassembling the final drive components of a 345C excavator. It begins by having the technician remove the final drive from the machine. It then instructs them to use various tools to disassemble the individual components of the final drive, including removing gears, shafts, seals, and housings. The disassembly process is described through 30 detailed steps with accompanying illustrations.
Caterpillar cat 345 c hydraulic excavator (prefix gcl) service repair manual ...fjsekqazxkdmmem
The document provides instructions for disassembling and assembling the final drive of a 345C excavator. It describes 30 steps to disassemble the final drive by removing components like the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. It then describes 27 steps to reassemble the final drive, including cleaning parts, applying anti-seize compound, installing bearings and seals, and adjusting the bearing preload using shims to achieve the proper dimensions. Precision is required to mark parts for correct reinstallation.
Caterpillar cat 345 c hydraulic excavator (prefix gcl) service repair manual ...fjskekmdm
The document provides instructions for disassembling and assembling the final drive of a 345C excavator. It describes 30 steps to disassemble the final drive by removing components like the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. It then describes 27 steps to reassemble the final drive, including cleaning parts, applying anti-seize compound, installing bearings and seals, and adjusting the bearing preload using shims to achieve the proper clearance. Precision is required to mark parts positions for correct reassembly.
Caterpillar cat 345 c hydraulic excavator (prefix els) service repair manual ...hfhjskedme
The document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C excavator. It describes removing over 30 individual parts including gears, shafts, housings and seals. Detailed illustrations are included to identify each part. Special tools are listed that are required, along with torque specifications for reinstalling components. The process is reversed for assembly, with parts reinstalled in the original locations and orientations.
Caterpillar cat 345 c l hydraulic excavator (prefix els) service repair manua...jjfksekdmejik
The document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C excavator. It describes removing 30 individual parts in 28 steps, including the final drive cover, carrier assemblies, ring gear, and other internal components. Reassembly follows the reverse order, with notes to reinstall parts in their original locations and orientations. Required tools include a transmission stand, link brackets, retaining ring pliers, eyebolts, a duo-cone seal installer, anti-seize compound, and thread lock compound.
Caterpillar cat 345 c l hydraulic excavator (prefix els) service repair manua...ifkkdkmdmd
The document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C excavator. It describes removing over 30 individual parts including gears, shafts, housings and seals. Detailed illustrations are included to identify each part. Special tools are listed that are required, along with torque specifications for reinstalling components. The process is reversed for assembly, with parts installed back in the original locations and orientations.
Caterpillar cat 345 c hydraulic excavator (prefix els) service repair manual ...fjkkekmdm
The document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C excavator. It describes removing over 30 individual parts including gears, shafts, housings and seals. Detailed illustrations are included to identify each part. Special tools are listed that are required, along with torque specifications for reinstalling components. The process is reversed for assembly, with parts reinstalled in the original locations and orientations.
Massey ferguson mf 135148 mkiii135145 vs tractors (fr) parts catalogue manualjjfksekdmejik
This document contains parts listings and descriptions for Massey Ferguson 135/148 MKIII/135/145 V/S tractors. It includes lists of parts for the engine and accessories in sections divided by serial number ranges. Lists of parts are also provided for the cylinder block, crankshaft, pistons, connecting rods, and cylinder head of the AD3.152 engine, each with accompanying part numbers and descriptions.
Massey ferguson mf 133135 mkiii135 v tractors parts catalogue manualjjfksekdmejik
The document provides a parts list for Massey Ferguson MF 133/135 MKIII/135 V tractors. It includes 37 items with part numbers, quantities, descriptions, and comments. The parts are grouped into sections including the engine and accessories, cylinder block, crankshaft, pistons, connecting rods, and cylinder head. The list provides replacement part numbers and notes differences for parts based on serial number and engine details.
Massey ferguson mf 7278 cerea combines parts catalogue manualjjfksekdmejik
The document provides a parts list and descriptions for the knives and fingers, right hand table auger, and left hand table auger components of Massey Ferguson MF 7272/7274/7278 CEREA combines for 20-22 foot headers. It includes 142 line items with part numbers, quantities, descriptions and additional information. The parts listed are for the cutting and conveying mechanisms and include knives, fingers, bearings, plates, shafts, arms and other components. Serial number ranges are specified for some parts to indicate application.
Massey ferguson mf 7276 combine parts catalogue manualjjfksekdmejik
1. The document provides a list of parts for the knives and fingers and table auger assemblies for Massey Ferguson MF 7274/7276 combines for header widths ranging from 16 to 22 feet.
2. It includes 142 line items with part numbers, quantities, descriptions, and additional comments for each part.
3. The parts are grouped into those for the knives and fingers freeflow assembly and the table auger right and left hand assemblies. Footnotes provide additional information on specific parts applications.
Massey ferguson mf 7274 combine parts catalogue manualjjfksekdmejik
1. The document provides a list of parts for the knives and fingers and table auger assemblies for Massey Ferguson MF 7274/7276 combines for various header widths ranging from 16 to 22 feet.
2. It includes the part numbers, quantities, descriptions, and any relevant comments for 142 unique parts across both assemblies.
3. The parts are organized into tables with the item number, part number, quantity, description, and any applicable comments or footnotes provided for each part.
Massey ferguson mf 7274 cerea combines parts catalogue manualjjfksekdmejik
The document provides a parts list and descriptions for the knives and fingers, right hand table auger, and left hand table auger components of Massey Ferguson MF 7272/7274/7278 CEREA combines for 20-22 foot headers. It lists over 150 individual part numbers, quantities, and additional identifying information for each component. Key parts include blades, fingers, bearings, plates, shafts, arms, and covers for the cutting and conveying mechanisms. Serial numbers are specified for some parts to indicate application ranges.
Massey ferguson mf 7272 combine parts catalogue manualjjfksekdmejik
This document provides a parts list for a Massey Ferguson MF 7272 combine. It includes 142 items with part numbers, descriptions, and other details. The parts are for the knives and fingers, table augers, and other components of the combine ranging from 16 to 20 feet. Footnotes provide additional information on some parts and their application depending on the serial number of the combine.
Massey ferguson mf 7272 cerea combines parts catalogue manualjjfksekdmejik
The document provides a list of parts for the knives and fingers and table augers of Massey Ferguson MF 7272/7274/7278 CEREA combines. It includes 142 items with part numbers, quantities, descriptions, and other details. The high-level functions of the parts listed are for cutting crops with knives and conveying them with table augers on the left and right sides of the combines. The parts support knives and fingers for cutting crops and table augers for moving cut crops on the left and right sides of the combines.
Massey ferguson mf 7256 combine parts catalogue manualjjfksekdmejik
This document provides a parts list for the knives and fingers and table auger components for a Massey Ferguson MF 7254/7256 combine harvester. It includes 142 numbered items with corresponding part numbers and descriptions. Footnotes provide additional part number options and application details for some components. The parts listed are for freeflow headers ranging from 14 to 20 feet in width.
Massey ferguson mf 7256 cerea combine parts catalogue manualjjfksekdmejik
This document provides a list of parts for the table auger and knives on a Massey Ferguson MF 7256 CEREA COMBINE. It includes over 130 individual part numbers, quantities, descriptions, and other identifying information for components ranging from clips and bolts to the table auger, knife blades, and auto header height control system. The parts cover header widths ranging from 14 to 20 feet.
Massey ferguson mf 7254 combine parts catalogue manualjjfksekdmejik
This document provides a parts list for the knives and fingers and table auger components for a Massey Ferguson MF 7254/7256 combine harvester. It includes 142 numbered items with corresponding part numbers and descriptions. Footnotes provide additional part number options and application details for some components. The parts listed are for freeflow headers ranging from 14 to 20 feet in width.
Massey ferguson mf 7252 combine parts catalogue manualjjfksekdmejik
The document provides a list of parts for the knives and fingers and table auger assemblies for a Massey Ferguson MF 7250/7252 combine. It includes 142 line items specifying the part numbers, quantities, descriptions and additional comments for each component. The assemblies cover header widths ranging from 14 feet to 20 feet.
Massey ferguson mf 7250 combine parts catalogue manualjjfksekdmejik
The document provides a list of parts for the knives and fingers and table auger assemblies for a Massey Ferguson MF 7250/7252 combine. It includes 142 line items specifying the part numbers, quantities, descriptions and additional comments for each component. The assemblies cover header widths ranging from 14' to 20'.
This document is a shop manual for a Komatsu PC3000-6 hydraulic mining shovel with serial number PC3000-6 6219. It contains instructions for maintenance and repair of major components. The manual begins with safety warnings and tables of contents. It then provides specifications and overview descriptions of the shovel's main assembly groups and systems, including the drive system, hydraulic oil reservoir, and other components. Technicians are instructed to follow the manual's guidelines for personal and operational safety.
This 3-sentence summary provides the key details from the document:
The document is an operation and maintenance manual for a Komatsu Mining Germany GmbH hydraulic mining shovel with serial number PC3000-1 6193, with information that is proprietary and not to be reproduced without authorization. Komatsu reserves the right to make changes or improvements to their products at any time without needing to update previously sold products, as their research and development results in regular revisions to manuals. Customers are advised to contact their distributor for information on the latest revision of manuals.
More Related Content
Similar to Caterpillar cat 345 c l hydraulic excavator (prefix gcl) service repair manual (gcl00001 and up)
Caterpillar cat 345 c l hydraulic excavator (prefix gcl) service repair manua...fjjskqazxedmmem
The document provides step-by-step instructions for disassembling the final drive components of a 345C excavator. It begins by having the technician remove the final drive from the machine. It then instructs them to use various tools to disassemble the individual components of the final drive, including removing gears, shafts, seals, and housings. The disassembly process is described through 30 detailed steps with accompanying illustrations.
Caterpillar cat 345 c hydraulic excavator (prefix gcl) service repair manual ...fjsekqazxkdmmem
The document provides instructions for disassembling and assembling the final drive of a 345C excavator. It describes 30 steps to disassemble the final drive by removing components like the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. It then describes 27 steps to reassemble the final drive, including cleaning parts, applying anti-seize compound, installing bearings and seals, and adjusting the bearing preload using shims to achieve the proper dimensions. Precision is required to mark parts for correct reinstallation.
Caterpillar cat 345 c hydraulic excavator (prefix gcl) service repair manual ...fjskekmdm
The document provides instructions for disassembling and assembling the final drive of a 345C excavator. It describes 30 steps to disassemble the final drive by removing components like the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. It then describes 27 steps to reassemble the final drive, including cleaning parts, applying anti-seize compound, installing bearings and seals, and adjusting the bearing preload using shims to achieve the proper clearance. Precision is required to mark parts positions for correct reassembly.
Caterpillar cat 345 c hydraulic excavator (prefix els) service repair manual ...hfhjskedme
The document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C excavator. It describes removing over 30 individual parts including gears, shafts, housings and seals. Detailed illustrations are included to identify each part. Special tools are listed that are required, along with torque specifications for reinstalling components. The process is reversed for assembly, with parts reinstalled in the original locations and orientations.
Caterpillar cat 345 c l hydraulic excavator (prefix els) service repair manua...jjfksekdmejik
The document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C excavator. It describes removing 30 individual parts in 28 steps, including the final drive cover, carrier assemblies, ring gear, and other internal components. Reassembly follows the reverse order, with notes to reinstall parts in their original locations and orientations. Required tools include a transmission stand, link brackets, retaining ring pliers, eyebolts, a duo-cone seal installer, anti-seize compound, and thread lock compound.
Caterpillar cat 345 c l hydraulic excavator (prefix els) service repair manua...ifkkdkmdmd
The document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C excavator. It describes removing over 30 individual parts including gears, shafts, housings and seals. Detailed illustrations are included to identify each part. Special tools are listed that are required, along with torque specifications for reinstalling components. The process is reversed for assembly, with parts installed back in the original locations and orientations.
Caterpillar cat 345 c hydraulic excavator (prefix els) service repair manual ...fjkkekmdm
The document provides step-by-step instructions for disassembling and assembling the final drive components of a 345C excavator. It describes removing over 30 individual parts including gears, shafts, housings and seals. Detailed illustrations are included to identify each part. Special tools are listed that are required, along with torque specifications for reinstalling components. The process is reversed for assembly, with parts reinstalled in the original locations and orientations.
Similar to Caterpillar cat 345 c l hydraulic excavator (prefix gcl) service repair manual (gcl00001 and up) (7)
Massey ferguson mf 135148 mkiii135145 vs tractors (fr) parts catalogue manualjjfksekdmejik
This document contains parts listings and descriptions for Massey Ferguson 135/148 MKIII/135/145 V/S tractors. It includes lists of parts for the engine and accessories in sections divided by serial number ranges. Lists of parts are also provided for the cylinder block, crankshaft, pistons, connecting rods, and cylinder head of the AD3.152 engine, each with accompanying part numbers and descriptions.
Massey ferguson mf 133135 mkiii135 v tractors parts catalogue manualjjfksekdmejik
The document provides a parts list for Massey Ferguson MF 133/135 MKIII/135 V tractors. It includes 37 items with part numbers, quantities, descriptions, and comments. The parts are grouped into sections including the engine and accessories, cylinder block, crankshaft, pistons, connecting rods, and cylinder head. The list provides replacement part numbers and notes differences for parts based on serial number and engine details.
Massey ferguson mf 7278 cerea combines parts catalogue manualjjfksekdmejik
The document provides a parts list and descriptions for the knives and fingers, right hand table auger, and left hand table auger components of Massey Ferguson MF 7272/7274/7278 CEREA combines for 20-22 foot headers. It includes 142 line items with part numbers, quantities, descriptions and additional information. The parts listed are for the cutting and conveying mechanisms and include knives, fingers, bearings, plates, shafts, arms and other components. Serial number ranges are specified for some parts to indicate application.
Massey ferguson mf 7276 combine parts catalogue manualjjfksekdmejik
1. The document provides a list of parts for the knives and fingers and table auger assemblies for Massey Ferguson MF 7274/7276 combines for header widths ranging from 16 to 22 feet.
2. It includes 142 line items with part numbers, quantities, descriptions, and additional comments for each part.
3. The parts are grouped into those for the knives and fingers freeflow assembly and the table auger right and left hand assemblies. Footnotes provide additional information on specific parts applications.
Massey ferguson mf 7274 combine parts catalogue manualjjfksekdmejik
1. The document provides a list of parts for the knives and fingers and table auger assemblies for Massey Ferguson MF 7274/7276 combines for various header widths ranging from 16 to 22 feet.
2. It includes the part numbers, quantities, descriptions, and any relevant comments for 142 unique parts across both assemblies.
3. The parts are organized into tables with the item number, part number, quantity, description, and any applicable comments or footnotes provided for each part.
Massey ferguson mf 7274 cerea combines parts catalogue manualjjfksekdmejik
The document provides a parts list and descriptions for the knives and fingers, right hand table auger, and left hand table auger components of Massey Ferguson MF 7272/7274/7278 CEREA combines for 20-22 foot headers. It lists over 150 individual part numbers, quantities, and additional identifying information for each component. Key parts include blades, fingers, bearings, plates, shafts, arms, and covers for the cutting and conveying mechanisms. Serial numbers are specified for some parts to indicate application ranges.
Massey ferguson mf 7272 combine parts catalogue manualjjfksekdmejik
This document provides a parts list for a Massey Ferguson MF 7272 combine. It includes 142 items with part numbers, descriptions, and other details. The parts are for the knives and fingers, table augers, and other components of the combine ranging from 16 to 20 feet. Footnotes provide additional information on some parts and their application depending on the serial number of the combine.
Massey ferguson mf 7272 cerea combines parts catalogue manualjjfksekdmejik
The document provides a list of parts for the knives and fingers and table augers of Massey Ferguson MF 7272/7274/7278 CEREA combines. It includes 142 items with part numbers, quantities, descriptions, and other details. The high-level functions of the parts listed are for cutting crops with knives and conveying them with table augers on the left and right sides of the combines. The parts support knives and fingers for cutting crops and table augers for moving cut crops on the left and right sides of the combines.
Massey ferguson mf 7256 combine parts catalogue manualjjfksekdmejik
This document provides a parts list for the knives and fingers and table auger components for a Massey Ferguson MF 7254/7256 combine harvester. It includes 142 numbered items with corresponding part numbers and descriptions. Footnotes provide additional part number options and application details for some components. The parts listed are for freeflow headers ranging from 14 to 20 feet in width.
Massey ferguson mf 7256 cerea combine parts catalogue manualjjfksekdmejik
This document provides a list of parts for the table auger and knives on a Massey Ferguson MF 7256 CEREA COMBINE. It includes over 130 individual part numbers, quantities, descriptions, and other identifying information for components ranging from clips and bolts to the table auger, knife blades, and auto header height control system. The parts cover header widths ranging from 14 to 20 feet.
Massey ferguson mf 7254 combine parts catalogue manualjjfksekdmejik
This document provides a parts list for the knives and fingers and table auger components for a Massey Ferguson MF 7254/7256 combine harvester. It includes 142 numbered items with corresponding part numbers and descriptions. Footnotes provide additional part number options and application details for some components. The parts listed are for freeflow headers ranging from 14 to 20 feet in width.
Massey ferguson mf 7252 combine parts catalogue manualjjfksekdmejik
The document provides a list of parts for the knives and fingers and table auger assemblies for a Massey Ferguson MF 7250/7252 combine. It includes 142 line items specifying the part numbers, quantities, descriptions and additional comments for each component. The assemblies cover header widths ranging from 14 feet to 20 feet.
Massey ferguson mf 7250 combine parts catalogue manualjjfksekdmejik
The document provides a list of parts for the knives and fingers and table auger assemblies for a Massey Ferguson MF 7250/7252 combine. It includes 142 line items specifying the part numbers, quantities, descriptions and additional comments for each component. The assemblies cover header widths ranging from 14' to 20'.
This document is a shop manual for a Komatsu PC3000-6 hydraulic mining shovel with serial number PC3000-6 6219. It contains instructions for maintenance and repair of major components. The manual begins with safety warnings and tables of contents. It then provides specifications and overview descriptions of the shovel's main assembly groups and systems, including the drive system, hydraulic oil reservoir, and other components. Technicians are instructed to follow the manual's guidelines for personal and operational safety.
This 3-sentence summary provides the key details from the document:
The document is an operation and maintenance manual for a Komatsu Mining Germany GmbH hydraulic mining shovel with serial number PC3000-1 6193, with information that is proprietary and not to be reproduced without authorization. Komatsu reserves the right to make changes or improvements to their products at any time without needing to update previously sold products, as their research and development results in regular revisions to manuals. Customers are advised to contact their distributor for information on the latest revision of manuals.
This document is the operation and maintenance manual for a Komatsu PC2000-8 hydraulic excavator. It provides important safety information and instructions for operating and servicing the excavator. Operators and maintenance personnel must read this manual thoroughly before working on the machine to understand safety precautions and procedures. The manual includes sections on safety, machine operation, maintenance information, and component descriptions.
Caterpillar cat 938 f wheel loader (prefix 7sn) service repair manual (7sn000...jjfksekdmejik
This document provides instructions for disassembling and assembling the torque converter and transmission of a Caterpillar 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and other internal parts. The multi-step process is intended to allow maintenance and repair of these core powertrain systems.
Caterpillar cat 938 f wheel loader (prefix 1km) service repair manual (1km000...jjfksekdmejik
This document provides instructions for installing a crankshaft on a 3116 engine. It lists the required tools and notes to keep parts clean and ensure crankshaft bearing tabs engage properly. The instructions describe installing main bearings, placing the crankshaft in the cylinder block, installing bearing caps and bolts, and checking end play clearance. References are provided for crankshaft reusability guidelines and specifications.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...jjfksekdmejik
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating the ring gear, applying threadlock, and tightening bolts.
4. Removing the crankshaft rear seal by removing bolts.
The document contains detailed step-by-step instructions, illustrations, and notes about required tools and inspection procedures.
Caterpillar cat 345 d l excavator (prefix rgg) service repair manual (rgg0000...jjfksekdmejik
This document provides instructions for disassembling and assembling the travel motor of a 345D L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pins, and piston assemblies. Special care must be taken to clean parts and ensure they are reinstalled in their original locations. Proper assembly prevents damage and contamination of parts.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR GCL
Configuration: 345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345C Excavator and 345C MHPU
Mobile Hydraulic Power Unit Machine Systems
Media Number -RENR8612-06 Publication Date -01/02/2013 Date Updated -21/02/2013
i05331566
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Stand Group 1
B 138-7573 Link Bracket 2
C 1P-1860 Retaining Ring Pliers 1
D 4C-8359 Eyebolt 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
Start By:
A. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive and Travel Motor
- Remove" in this manual.
1. Thoroughly clean the outside of the final drive and travel motor prior to disassembly.
1/13
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01207795
2. Remove coupling (1) from final drive (2) .
3. Attach a suitable lifting device to the final drive, and turn final drive (2) over 180 degrees.
The weight of final drive (2) is approximately 590 kg (1300 lb).
Illustration 2 g01207796
4. Attach the final drive to Tooling (A) . Put an alignment mark across the sections of the final
drive for assembly purposes. All parts must be reinstalled in the original locations.
5. Remove socket head screws (3) from the final drive cover.
2/13
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01207801
6. Attach Tooling (B) and a suitable lifting device to cover (5) , as shown. The weight of cover
(5) is approximately 52 kg (115 lb).
7. Remove bolts (4) and the washers that hold the cover in place.
8. Use a soft faced hammer in order to break the seal between cover (5) and the ring gear.
Remove cover (5) . The weight of cover (5) is 52 kg (115 lb).
Illustration 4 g01207835
9. Remove spacer (6) from the cover.
3/13
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g01207845
10. Remove shims (7) from the cover.
11. Remove socket head bolts (8) and ring gear (9) from the cover.
Illustration 6 g01207864
12. Remove sun gear (10) from carrier assembly (11) . Remove carrier assembly (11) by lifting
the carrier assembly straight up.
13. Disassemble carrier assembly (11) , as follows:
4/13
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 7 g01207865
a. Remove spacers (12) . A spacer is located on each side of the sun gear in carrier
assembly (11) .
Note: Planetary gears (15) might be stamped with identification marks "L". Note the
position of the identification marks in relation to the carrier for assembly purposes.
Illustration 8 g01207897
b. Remove retaining ring (13) with Tooling (C) .
c. Remove thrust washers (14) and planetary gear (15) from the carrier.
d. Remove bearing (16) from the planetary gear.
e. Repeat Steps 13.b through 13.d for the other two planetary gears.
Illustration 9 g01208035
f. Use a screwdriver in order to remove retaining ring (17) from the carrier. Remove sun
gear (18) from the carrier.
5/13
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g01208136
14. Attach Tooling (D) and a suitable lifting device to carrier assembly (19) , as shown.
Remove carrier assembly (19) by pulling the carrier assembly straight up. The weight of
carrier assembly (19) is approximately 45 kg (100 lb).
15. Disassemble carrier assembly (19) , as follows:
Note: Spacer (20) may remain with carrier assembly (19) , or the spacer may remain with
carrier assembly (28) . Refer to Step 17.
Illustration 11 g01208162
a. Remove spacer (20) from carrier assembly (19) .
6/13
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 12 g01208169
b. Drive spring pin (21) into planetary shaft (22) with a hammer and a punch.
Illustration 13 g01208189
c. Remove planetary shaft (22) , two thrust washers (23) and planetary gear (24) from
the carrier.
Note: Planetary gears (24) might be stamped with identification marks "M". Note the
position of the identification marks in relation to the carrier for assembly purposes.
d. Remove bearing (25) from the planetary gear.
e. Remove spring pin (21) from planetary shaft (22) with a hammer and a punch.
f. Repeat Steps 15.b through 15.e in order to remove the other two planetary gears from
the carrier.
7/13
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 14 g01208245
g. Use a screwdriver to remove retaining ring (26) . Remove sun gear (27) from the
carrier.
Illustration 15 g01208253
16. If spacer (20) was not removed in Step 15.a, remove the spacer from carrier assembly (28)
at this time.
Illustration 16 g01208256
8/13
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 17. Attach Tooling (E) and a suitable lifting device to carrier assembly (28) , as shown. Remove
carrier assembly (28) . The weight of carrier assembly (28) is approximately 64 kg (140 lb).
18. Disassemble carrier assembly (28) , as follows:
Illustration 17 g01208265
a. Drive spring pin (29) into planetary shaft (30) with a hammer and a punch.
Illustration 18 g01208280
b. Remove planetary shaft (30) , two thrust washers (31) , and planetary gear (32) from
the carrier.
Note: Planetary gears (32) might be stamped with identification marks "N". Note the
position of the identification marks in relation to the carrier for assembly purposes.
c. Remove bearings (33) from the planetary gear.
d. Drive spring pin (29) out of planetary shaft (30) with a hammer and a punch.
e. Repeat Steps 18.a through 18.d in order to remove the other three planetary gears
from the carrier.
9/13
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g01208300
19. Fasten Tooling (E) and a suitable lifting device to ring gear (34) , as shown. Remove ring
gear (34) from sprocket housing (35) . The weight of ring gear (34) is approximately 82 kg
(180 lb).
Illustration 20 g01208542
20. Remove O-ring seal (36) from sprocket housing (35) .
10/13
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY ...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 21 g01208553
Note: Mark the orientation of coupling (38) for assembly purposes.
21. Remove bolts (37) from coupling gear (38) .
Illustration 22 g01208572
22. Install suitable forcing bolts (39) in coupling gear (38) , as shown. Tighten the forcing bolts
evenly in order to loosen coupling gear (38) . Remove the coupling gear from the motor
housing.
Illustration 23 g01208578
11/13
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY ...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 24 g01208625
23. Remove shims (40) from the motor housing.
Note: Inner cones and outer bearing cones (42) are a slip fit on the motor housing. While
you remove sprocket housing (35) from the motor housing, inner bearing cone (42) may
stay with the sprocket housing or the inner bearing cone may stay on the motor housing.
24. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35) , as shown.
Separate the sprocket housing from the motor housing. The weight of sprocket housing (35)
is 127 kg (280 lb).
Illustration 25 g01208626
25. Remove the locating pins from the motor housing.
26. Remove duo-cone seal gp (41) from the motor housing.
27. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.
12/13
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY ...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 26 g01208633
28. Remove duo-cone seal gp (43) from the sprocket housing.
29. If inner bearing cone (42) remained on the sprocket housing, then remove the inner bearing
cone.
30. Remove the bearing cups from the sprocket housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 15:28:39 UTC+0800 2020
13/13
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY ...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR GCL
Configuration: 345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C13 Engine
Disassembly and Assembly
345C Excavator and 345C MHPU
Mobile Hydraulic Power Unit Machine Systems
Media Number -RENR8612-06 Publication Date -01/02/2013 Date Updated -21/02/2013
i05970668
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1860 Retaining Ring Pliers 1
D 4C-8359 Eyebolt 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G 8T-0531 Duo-Cone Seal Installer As 1
H 4C-5599 Anti-Seize Compound 1
J 9S-3263 Thread Lock Compound 1
K 1U-8846 Gasket Sealant 1
L 6V-7059 Micrometer 1
M 1U-9895 Crossblock 1
1. Make sure that all parts of the final drive are thoroughly clean and free of dirt and debris
prior to assembly. Check the condition of all O-ring seals that are used in the final drive. If
1/20
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. any of the seals are damaged, use new parts for replacement. Reassemble the final drive on
Tooling (A) .
Illustration 1 g01208879
2. Apply Tooling (H) to the surfaces inside sprocket housing (35) that makes contact with the
bearing cups. Install a bearing cup that is in each side of the sprocket housing with a press.
Make sure that the bearing cups are properly seated.
3. Apply Tooling (H) to the surfaces inside the motor housing that makes contact with bearing
cones (42) .
4. Install inner bearing cone (42) on the motor housing.
Illustration 2 g01208625
5. Apply Tooling (F) and a suitable lifting device to sprocket housing (35) , as shown. The
weight of sprocket housing (35) is approximately 127 kg (280 lb). Install sprocket housing
(35) on the motor housing. Carefully install outer bearing cone (42) on the sprocket housing.
2/20
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g01208578
6. Adjust the bearing preload of the final drive. Determine the correct number of shims (40)
that are required for the proper bearing preload, as follows:
Illustration 4 g01208987
a. Use a depth micrometer in order to measure the step height of coupling gear (38) at
several locations around the gear. Find the average for the measured dimensions
around the gear and record the dimension. Call this Dimension (X) .
b. Apply a load of 10000 kg (22000 lb)to bearing cones (42) .
c. Rotate sprocket housing (35) several times in order to seat the bearing cones.
d. Reduce the load to 3500 ± 350 kg (7700 ± 770 lb).
3/20
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 5 g00631001
Illustration 6 g03742848
e. While the load is still on the bearing cones, measure the distance between the top face
of the motor housing and the top face of bearing cone (42) . Take measurements in
several locations around the motor housing. Find the average of the measured
dimensions, and record the dimensions. Call this Dimension (Y) .
f. Determine the correct thickness of shims (40) which are used between bearing cone
(42) and coupling gear (38) . Use the following equation in order to determine the
shim pack thickness.
Shim pack thickness ... (X) − (Y) ± 0.05 mm (0.002 inch)
Note: If shims (40) are required, install the thinnest shim next to coupling gear (38)
during final assembly.
4/20
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 7 g01208625
7. Apply Tooling (F) and a suitable lifting device to sprocket housing (35) , as shown.
Separate sprocket housing (35) from the motor housing.
ReferenceRefer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that makes contact with the seals must be clean and
dry. After installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal
seals.
Illustration 8 g00631006
5/20
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 9 g01208999
8. Install Duo-Cone seal kit (43) in the sprocket housing with Tooling (G) .
Illustration 10 g00631014
Illustration 11 g01208626
Illustration 12 g01208625
6/20
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 9. Install Duo-Cone seal kit (41) in the motor housing with Tooling (G) .
10. ApplyTooling (H) in the bores for the locating pins that are in the motor housing. Reinstall
the locating pins in the motor housing.
11. Make sure that inner bearing cone (42) is seated properly on the motor housing.
Note: Do not scratch Duo-Cone seal gp (41) or damage the Duo-Cone seal gp in the main
housing, or the motor housing during assembly of the two components. After installation of
the main housing on the motor housing, there will be a small gap between the components.
The gap between the components is caused by the Duo-Cone seal kit. This will be
eliminated during the installation of the coupling gear.
12. Attach Tooling (F) and a suitable lifting device to sprocket housing (35) , as shown.
Carefully install the sprocket housing on the motor housing.
13. Install outer bearing cone (42) on the sprocket housing. Make sure that the outer bearing
cone is properly seated.
Illustration 13 g01208578
14. Install shims (40) that were determined in Steps 6.a through 6.f on the end of the sprocket
housing, as shown. If shims were required, make sure that the thinnest shim is installed on
top.
7/20
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 14 g01208553
15. Put coupling gear (38) in the original position on the motor housing.
16. Apply Tooling (J) on the threads of bolts (37) that hold coupling gear (38) in position.
Tighten bolts (37) evenly and tighten the bolts in diagonally opposite pairs.
Illustration 15 g01208542
17. Install O-ring seal (36) in sprocket housing (35) .
Illustration 16 g01208300
18. Thoroughly clean the mating surface of sprocket housing (35) that will make contact with
ring gear (34) .
19. Apply a bead of Tooling (K) on the mating surface of ring gear (34) .
20. Attach Tooling (E) and a suitable lifting device to ring gear (34) . Put ring gear (34) in
position on the sprocket housing. The weight of ring gear (34) is approximately 82 kg (180
lb). Make sure that the alignment mark up on the sprocket housing and the ring gear line
with each other.
8/20
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY C...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 19 g00513451
21. Assemble carrier assembly (28) , as follows:
Note: If planetary gear (32) is stamped with an "N", make sure that the planetary gear
identification grooves are facing in the correct direction, which was noted during the
disassembly of the carrier assembly (28) .
a. Assemble carrier assembly (28) .
b. Put clean SAE 30 oil on bearings (33) .
c. Install bearings (33) in planetary gear (32) .
d. Install a thrust washer (31) on each side of the planetary gear.
e. Install the planetary gear and thrust washers in carrier (28) .
f. Install planetary shaft (30) in carrier (28) and through planetary gear (32) . Make sure
that the spring pin hole in the planetary shaft is in alignment with the spring pin hole
in the carrier.
g. Install spring pin (29) in the carrier and into the planetary shaft. Install the spring pin
until the spring pin is even with the outside surface of the carrier. Orient the split in
the spring pin horizontally to the carrier. Align the split in the spring pin to the left or
to the right. Refer to Illustration 19.
h. Make a stake mark on each side of the spring pin hole in the carrier. This will prevent
the spring pin from falling out of the spring pin hole. Each stake mark should be
approximately 1.5 to 3.00 mm (.59 to .118 inch) from the spring pin hole.
i. Repeat Steps 21.a through 21.h in order to install the remaining three planetary gears
in carrier (30) .
Illustration 20 g01208256
22. Attach Tooling (E) and a suitable lifting device to carrier assembly (28) . The weight of
carrier assembly (28) is approximately 64 kg (140 lb). Put carrier assembly (28) in position
10/20
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY ...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. in the ring gear. It will be necessary to rotate carrier assembly (28) back and forth during
installation in order to engage all the gears properly.
Illustration 21 g01208253
23. Install spacer (20) on carrier assembly (28) .
24. Assemble carrier assembly (19) , as follows:
Illustration 22 g01208245
11/20
345C & 345C L Hydraulic Excavator GCL00001-UP (MACHINE) POWERED BY ...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...