This document provides instructions for removing and installing the rear gear group on a 345C excavator. It details:
1) The required tools and removal procedure which involves removing 14 components in 9 steps.
2) The installation procedure which involves properly installing and positioning 11 components in 11 steps, ensuring correct dimensions and alignments are followed. Special tools and loctite are required for installation.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
The document provides instructions for removing and installing various engine components on a Caterpillar C9.3B industrial engine. It includes steps for removing and installing the crankshaft rear seal, flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, and housing (front). Diagrams and part numbers for required tools are provided for each procedure. The document is part of a service manual for Caterpillar technicians repairing C9.3B engines.
Caterpillar cat 336 e l excavator (prefix yce) service repair manual (yce0000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove components like the motor head, springs, brake piston, rotating assembly, and seals. The assembly procedure describes 28 steps and requires various tools to reinstall the components in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Precautions are provided to watch for spring forces and avoid damaging mating surfaces.
Caterpillar cat 336 e l excavator (prefix dpx) service repair manual (dpx0000...fjskekmdm
This document provides instructions for disassembling and assembling a 336E L excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, O-rings, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly process in 21 steps and provides warnings about spring-loaded components and ensuring proper alignment of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, bearing puller group, and Loctite.
Caterpillar cat 336 e l excavator (prefix cmr) service repair manual (cmr0000...fjskekmdm
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove all components of the travel motor. Key steps include using an air pressure tool to remove the brake piston, pressing out bearing races, and removing springs. The assembly procedure reverses the disassembly process in 27 steps and provides details on lubricating parts and ensuring proper alignment of components like pistons and keys. Tools required include an adapter, nuts, washers, eyebolts, retaining ring pliers, a bearing puller, and Loctite.
Caterpillar cat 336 e l excavator (prefix bzy) service repair manual (bzy0000...fjskekmdm
This document provides instructions for disassembling and assembling a 336E L excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate and keys. Special tools are listed that are required for tasks like removing races and installing seals. Safety notices advise wearing protective equipment when working with spring-loaded parts.
This document provides instructions to remove and install the final drive and travel motor on a 323D3 excavator. The key steps are:
1. Position the final drive and travel motor in a cribbing and remove attachment bolts and covers.
2. Use pullers and eyebolts to separate the housing from the travel motor.
3. Remove seals, bearings, and other components from the housing and travel motor.
4. Clean all parts thoroughly and inspect for wear. Replace any worn parts.
5. Reassemble by installing bearings, seals and other components back into the housing and travel motor.
6. Apply anti-seize lubricant and use presses
Caterpillar cat 336 e l excavator (prefix jrj) service repair manual (jrj0000...fjskekmdm
The document provides instructions for disassembling and assembling the travel motor of a 336E L excavator. It lists 27 steps for disassembly, removing components like the head, springs, brake piston, plates and discs. It then lists 28 steps for assembly, reinstalling these components in reverse order and noting proper lubrication and torque specifications. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, bearing puller group and Loctite.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
The document provides instructions for removing and installing various engine components on a Caterpillar C9.3B industrial engine. It includes steps for removing and installing the crankshaft rear seal, flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, and housing (front). Diagrams and part numbers for required tools are provided for each procedure. The document is part of a service manual for Caterpillar technicians repairing C9.3B engines.
Caterpillar cat 336 e l excavator (prefix yce) service repair manual (yce0000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove components like the motor head, springs, brake piston, rotating assembly, and seals. The assembly procedure describes 28 steps and requires various tools to reinstall the components in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Precautions are provided to watch for spring forces and avoid damaging mating surfaces.
Caterpillar cat 336 e l excavator (prefix dpx) service repair manual (dpx0000...fjskekmdm
This document provides instructions for disassembling and assembling a 336E L excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, O-rings, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly process in 21 steps and provides warnings about spring-loaded components and ensuring proper alignment of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, bearing puller group, and Loctite.
Caterpillar cat 336 e l excavator (prefix cmr) service repair manual (cmr0000...fjskekmdm
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove all components of the travel motor. Key steps include using an air pressure tool to remove the brake piston, pressing out bearing races, and removing springs. The assembly procedure reverses the disassembly process in 27 steps and provides details on lubricating parts and ensuring proper alignment of components like pistons and keys. Tools required include an adapter, nuts, washers, eyebolts, retaining ring pliers, a bearing puller, and Loctite.
Caterpillar cat 336 e l excavator (prefix bzy) service repair manual (bzy0000...fjskekmdm
This document provides instructions for disassembling and assembling a 336E L excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate and keys. Special tools are listed that are required for tasks like removing races and installing seals. Safety notices advise wearing protective equipment when working with spring-loaded parts.
This document provides instructions to remove and install the final drive and travel motor on a 323D3 excavator. The key steps are:
1. Position the final drive and travel motor in a cribbing and remove attachment bolts and covers.
2. Use pullers and eyebolts to separate the housing from the travel motor.
3. Remove seals, bearings, and other components from the housing and travel motor.
4. Clean all parts thoroughly and inspect for wear. Replace any worn parts.
5. Reassemble by installing bearings, seals and other components back into the housing and travel motor.
6. Apply anti-seize lubricant and use presses
Caterpillar cat 336 e l excavator (prefix jrj) service repair manual (jrj0000...fjskekmdm
The document provides instructions for disassembling and assembling the travel motor of a 336E L excavator. It lists 27 steps for disassembly, removing components like the head, springs, brake piston, plates and discs. It then lists 28 steps for assembly, reinstalling these components in reverse order and noting proper lubrication and torque specifications. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, bearing puller group and Loctite.
This document provides removal and installation instructions for various components of a 345C excavator engine, including:
1) The rear gear group, which involves removing gears, seals, covers and bearings, taking care to properly install replacement bearings.
2) The flywheel, which requires specialized tools to lift it off due to its weight and to remove the ring gear.
3) The crankshaft rear seal, which is removed after taking off the flywheel. Precautions are described to contain fluids.
This document provides removal and installation instructions for various components of a 345C excavator engine. It describes how to remove and install the rear gear group, flywheel, rear crankshaft seal, and related components. The procedures include using various tools and following steps like removing bolts, seals, and covers, in the correct numerical order. Special precautions are outlined, such as containing fluids, cleaning parts, and applying threadlock.
This document provides removal and installation instructions for various components of a 345C excavator engine. It describes in step-by-step detail how to remove and install components like the rear gear group, flywheel, crankshaft rear seal, and more. Detailed illustrations and specifications are provided to ensure correct removal and installation of parts. Safety notices are included to handle fluids and contaminated parts properly.
Caterpillar cat d8 n track type tractor dozer bulldozer (prefix 1xj) service ...jfkskemwsxmdm
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a Caterpillar D8N track-type tractor with a 3406 engine. The removal procedure involves using various tools to remove 14 bolts and components including gears, covers, seals, and bearings. The installation procedure provides instructions to install these same components in reverse order and includes notes about cleaning, applying sealant, and ensuring proper dimensions and alignment. Proper tools and torque specifications are listed for each step.
Caterpillar cat d8 n track type tractor dozer bulldozer (prefix 1xj) service ...fujsekfksmemf
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar D8N track-type tractor with a 3406 engine. The removal procedure involves using tools to remove 11 components in 9 steps, including gears, covers, seals, and bearings. The installation procedure provides instructions to install 14 components in 12 steps, noting the proper orientation and temperature treatment of bearings.
Caterpillar cat d8 n track type tractor dozer bulldozer (prefix 1xj) service ...ufjjdjffjkskemm
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a Caterpillar D8N track-type tractor with a 3406 engine. The removal procedure involves using various tools to remove 14 bolts and components including gears, covers, seals, and bearings. The installation procedure provides instructions to install these same components in reverse order and includes notes about cleaning, applying sealant, and ensuring proper dimensions and alignment. Proper tools and torque specifications are listed for each step.
This document provides instructions for removing and installing components of the rear gear group and flywheel on a Caterpillar D8N track-type tractor powered by a 3406 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, various gears and covers. The installation procedure provides instructions for installing these components in reverse order and includes using specific tools and applying threadlock. Precautions are provided such as containing fluids and keeping parts clean from contaminants.
This document provides instructions for removing and installing components of the rear gear group and flywheel on a Caterpillar D8N track-type tractor powered by a 3406 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, various gears and covers. Tools required are listed. The installation procedure provides steps to install components in reverse order and notes on tool usage and specifications.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...jjfksekdmejik
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating the ring gear, applying threadlock, and tightening bolts.
4. Removing the crankshaft rear seal by removing bolts.
The document contains detailed step-by-step instructions, illustrations, and notes about required tools and inspection procedures.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and removing mounting bolts.
3. Removing the crankshaft rear seal by removing mounting bolts.
Detailed step-by-step instructions are provided along with illustrations to guide the process. Required tools are listed for each procedure. Precautions for handling components and proper installation techniques are also described.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...ifkkdkmdmd
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating components, applying threadlocker to bolts, and torquing bolts to specification.
4. Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...fjisejkdmd8id
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating components, applying threadlocker to bolts, and torquing bolts to specification.
4. Removing the crankshaft rear seal by removing bolts.
The document contains detailed step-by-step instructions, illustrations, and notes about required tools and inspection procedures.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f8sejdkdmdijd
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. The rear gear group, which involves removing several gears, seals, and bearings.
2. The flywheel, which requires lifting equipment and guide studs due to its weight.
3. The crankshaft rear seal, which is removed after removing the flywheel. Precise instructions are provided along with safety notices.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tools. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...yqen95561858
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...fjjseksxckmdme
This document provides instructions for disassembling and assembling the front axle of an M315C Wheeled Excavator. It begins with required tools and safety information. The 27 step disassembly process removes components like the carrier housing, planetary gears, brake assembly and bearings. The 22 step assembly process then rebuilds these components in reverse order, noting specifics like torque values and seal/bushing installation procedures. Precise assembly is required to properly rebuild the front axle.
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. Detailed steps describe each part removal and installation to correctly reassemble the travel motor.
This document provides instructions for removing and installing a swing motor and swing drive on an M315 excavator. It describes releasing hydraulic pressure, draining oil, disconnecting hoses, and removing and installing various components like bolts, seals, and motors. Safety precautions are provided regarding containing fluids, releasing pressure, and preventing personal injury. Detailed step-by-step instructions are given for disassembly and reassembly.
Caterpillar cat d6 r track type tractor (prefix 6jn) service repair manual (6...fjjseksxckmdme
This document provides assembly instructions for a Flexxaire fan on a D6R track-type tractor. It describes assembling the shifter block, hub, actuator bearings, carrier/spool, main bearing, and installing components like the O-ring and frost plug. The multi-step process involves placing various parts like bearings, washers, spacers and seals in the correct orientation and securing them with locknuts, applying thread lock compounds and grease. Tolerances and torque specifications are provided.
Caterpillar cat d6 r track type tractor (prefix 6hr) service repair manual (6...fjjseksxckmdme
1) The document provides instructions for removing and installing front track roller frames and recoil springs on a D6R track-type tractor.
2) It describes using various tooling to gradually compress the recoil springs and remove the retainer in increments to avoid injury.
3) Fifteen steps are outlined for installing the front track roller frame back onto the rear frame.
Caterpillar cat d6 r track type tractor (prefix 6gr) service repair manual (6...fjjseksxckmdme
The document provides instructions for removing and installing components of a D6R track-type tractor, including:
1) Removing the hydraulic control valve by draining hydraulic fluid, disconnecting hoses, and removing mounting bolts.
2) Disassembling the implement pump by removing mounting components, pistons, seals, and bearings.
3) Removing the hydraulic control linkage by disconnecting rods and removing mounting bolts, panels, and handles.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjjseksxckmdme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before installation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
More Related Content
Similar to Caterpillar cat 345 c excavator (prefix jar) service repair manual (jar00001 and up)
This document provides removal and installation instructions for various components of a 345C excavator engine, including:
1) The rear gear group, which involves removing gears, seals, covers and bearings, taking care to properly install replacement bearings.
2) The flywheel, which requires specialized tools to lift it off due to its weight and to remove the ring gear.
3) The crankshaft rear seal, which is removed after taking off the flywheel. Precautions are described to contain fluids.
This document provides removal and installation instructions for various components of a 345C excavator engine. It describes how to remove and install the rear gear group, flywheel, rear crankshaft seal, and related components. The procedures include using various tools and following steps like removing bolts, seals, and covers, in the correct numerical order. Special precautions are outlined, such as containing fluids, cleaning parts, and applying threadlock.
This document provides removal and installation instructions for various components of a 345C excavator engine. It describes in step-by-step detail how to remove and install components like the rear gear group, flywheel, crankshaft rear seal, and more. Detailed illustrations and specifications are provided to ensure correct removal and installation of parts. Safety notices are included to handle fluids and contaminated parts properly.
Caterpillar cat d8 n track type tractor dozer bulldozer (prefix 1xj) service ...jfkskemwsxmdm
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a Caterpillar D8N track-type tractor with a 3406 engine. The removal procedure involves using various tools to remove 14 bolts and components including gears, covers, seals, and bearings. The installation procedure provides instructions to install these same components in reverse order and includes notes about cleaning, applying sealant, and ensuring proper dimensions and alignment. Proper tools and torque specifications are listed for each step.
Caterpillar cat d8 n track type tractor dozer bulldozer (prefix 1xj) service ...fujsekfksmemf
This document provides instructions for removing and installing the rear gear group and flywheel on a Caterpillar D8N track-type tractor with a 3406 engine. The removal procedure involves using tools to remove 11 components in 9 steps, including gears, covers, seals, and bearings. The installation procedure provides instructions to install 14 components in 12 steps, noting the proper orientation and temperature treatment of bearings.
Caterpillar cat d8 n track type tractor dozer bulldozer (prefix 1xj) service ...ufjjdjffjkskemm
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a Caterpillar D8N track-type tractor with a 3406 engine. The removal procedure involves using various tools to remove 14 bolts and components including gears, covers, seals, and bearings. The installation procedure provides instructions to install these same components in reverse order and includes notes about cleaning, applying sealant, and ensuring proper dimensions and alignment. Proper tools and torque specifications are listed for each step.
This document provides instructions for removing and installing components of the rear gear group and flywheel on a Caterpillar D8N track-type tractor powered by a 3406 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, various gears and covers. The installation procedure provides instructions for installing these components in reverse order and includes using specific tools and applying threadlock. Precautions are provided such as containing fluids and keeping parts clean from contaminants.
This document provides instructions for removing and installing components of the rear gear group and flywheel on a Caterpillar D8N track-type tractor powered by a 3406 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, various gears and covers. Tools required are listed. The installation procedure provides steps to install components in reverse order and notes on tool usage and specifications.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...jjfksekdmejik
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating the ring gear, applying threadlock, and tightening bolts.
4. Removing the crankshaft rear seal by removing bolts.
The document contains detailed step-by-step instructions, illustrations, and notes about required tools and inspection procedures.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and removing mounting bolts.
3. Removing the crankshaft rear seal by removing mounting bolts.
Detailed step-by-step instructions are provided along with illustrations to guide the process. Required tools are listed for each procedure. Precautions for handling components and proper installation techniques are also described.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...ifkkdkmdmd
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating components, applying threadlocker to bolts, and torquing bolts to specification.
4. Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...fjisejkdmd8id
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. Removing the rear gear group by removing bolts, gears, seals, and bearings.
2. Removing the flywheel using lifting tools and guide studs.
3. Installing the flywheel by heating components, applying threadlocker to bolts, and torquing bolts to specification.
4. Removing the crankshaft rear seal by removing bolts.
The document contains detailed step-by-step instructions, illustrations, and notes about required tools and inspection procedures.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f8sejdkdmdijd
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. The rear gear group, which involves removing several gears, seals, and bearings.
2. The flywheel, which requires lifting equipment and guide studs due to its weight.
3. The crankshaft rear seal, which is removed after removing the flywheel. Precise instructions are provided along with safety notices.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual Instant D...fujkskemdmdm4r
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tools. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...yqen95561858
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
Similar to Caterpillar cat 345 c excavator (prefix jar) service repair manual (jar00001 and up) (15)
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...fjjseksxckmdme
This document provides instructions for disassembling and assembling the front axle of an M315C Wheeled Excavator. It begins with required tools and safety information. The 27 step disassembly process removes components like the carrier housing, planetary gears, brake assembly and bearings. The 22 step assembly process then rebuilds these components in reverse order, noting specifics like torque values and seal/bushing installation procedures. Precise assembly is required to properly rebuild the front axle.
This document provides instructions for disassembling and assembling the travel motor on a M315 Excavator. It involves removing and installing various components like hoses, valves, seals, bearings, and housings. Safety precautions are outlined to release hydraulic pressure before disassembly and ensure fluids are properly contained. Detailed steps describe each part removal and installation to correctly reassemble the travel motor.
This document provides instructions for removing and installing a swing motor and swing drive on an M315 excavator. It describes releasing hydraulic pressure, draining oil, disconnecting hoses, and removing and installing various components like bolts, seals, and motors. Safety precautions are provided regarding containing fluids, releasing pressure, and preventing personal injury. Detailed step-by-step instructions are given for disassembly and reassembly.
Caterpillar cat d6 r track type tractor (prefix 6jn) service repair manual (6...fjjseksxckmdme
This document provides assembly instructions for a Flexxaire fan on a D6R track-type tractor. It describes assembling the shifter block, hub, actuator bearings, carrier/spool, main bearing, and installing components like the O-ring and frost plug. The multi-step process involves placing various parts like bearings, washers, spacers and seals in the correct orientation and securing them with locknuts, applying thread lock compounds and grease. Tolerances and torque specifications are provided.
Caterpillar cat d6 r track type tractor (prefix 6hr) service repair manual (6...fjjseksxckmdme
1) The document provides instructions for removing and installing front track roller frames and recoil springs on a D6R track-type tractor.
2) It describes using various tooling to gradually compress the recoil springs and remove the retainer in increments to avoid injury.
3) Fifteen steps are outlined for installing the front track roller frame back onto the rear frame.
Caterpillar cat d6 r track type tractor (prefix 6gr) service repair manual (6...fjjseksxckmdme
The document provides instructions for removing and installing components of a D6R track-type tractor, including:
1) Removing the hydraulic control valve by draining hydraulic fluid, disconnecting hoses, and removing mounting bolts.
2) Disassembling the implement pump by removing mounting components, pistons, seals, and bearings.
3) Removing the hydraulic control linkage by disconnecting rods and removing mounting bolts, panels, and handles.
Caterpillar cat d6 r track type tractor (prefix 6fr) service repair manual (6...fjjseksxckmdme
The document provides instructions for removing and installing idler rollers and equalizer bars on a Caterpillar D6R track-type tractor. Key steps include using hoists and tools to remove idlers and bolts/retainers, cleaning and inspecting parts, lubricating seals with isopropyl alcohol, and testing assemblies for leaks before installation. Special tools are required to correctly set seal depths and check end play clearance during assembly.
Caterpillar cat d6 r track type tractor (prefix 5rr) service repair manual (5...fjjseksxckmdme
The document provides instructions for removing and installing various engine components on a Caterpillar D6R track-type tractor, including:
1. Removing and installing the spacer plate, which involves removing seals and gaskets.
2. Removing and installing water directors by removing them from the cylinder head and pressing new ones in at a specified depth.
3. Removing and installing the lifter group using a magnetic tool and checking lifter diameters.
4. Removing and installing the camshaft by aligning timing marks, removing bolts and gears, cleaning parts, and reinstalling with lubricant while rotating to prevent binding.
Caterpillar cat d6 r track type tractor (prefix 5pr) service repair manual (5...fjjseksxckmdme
The document provides instructions for removing and installing a spacer plate on a D6R track-type tractor with a 3306 engine. It describes removing the cylinder head, O-rings, seals, and spacer plate. It then details cleaning surfaces, installing new gaskets and seals, and reinstalling the spacer plate and cylinder head. The process also includes checking cylinder liner projection after installation.
Caterpillar cat d6 r track type tractor (prefix 5ln) service repair manual (5...fjjseksxckmdme
This document provides instructions for disassembling and assembling components of the fuel injection system for Caterpillar 3304B and 3306B engines. It describes how to disassemble the governor by removing the fuel ratio control and mounting bolts. Proper cleaning of parts to prevent contamination is emphasized. The assembly procedure explains how to install bearings and other components in the fuel injection pump housing using various tools, and how to set the timing when installing the pump and governor.
Caterpillar cat d6 r track type tractor (prefix 4wr) service repair manual (4...fjjseksxckmdme
The document provides instructions for removing and installing final drives, steering clutches, and brakes on a D6R track-type tractor. Key steps include draining oil, removing covers and shafts, using lifting tools to remove heavy components, and reinstalling parts in reverse order while applying new seals and grease. Detailed diagrams show tooling and component locations to aid the process.
The document provides removal and installation instructions for a precooler, water temperature regulator housing, water pump, and other engine components. It includes illustrations and lists required tools. The procedures describe disconnecting hoses and harness assemblies, removing bolts and parts like housings and manifolds, and installing components in the reverse order of removal while applying sealant compounds and ensuring cleanliness. Cautions are provided about containing fluids and preventing contamination.
This document provides instructions for installing and removing components of the front gear group of a C18 industrial engine. It describes:
1. Cleaning and inspecting parts before installation and applying thread locking compound to bolts.
2. Installing the front plate, gears, and shafts in the correct order and orientation while adjusting backlash.
3. Torquing bolts and nuts to specified values after applying thread locking compound.
This document provides instructions for removing and installing a cylinder head on a C18 industrial engine. It includes:
1) Detailed steps for removing the cylinder head such as disconnecting hoses, sensors, and removing bolts.
2) Instructions for installing seals, gaskets and the cylinder head, applying anti-seize compound to bolts, and tightening the bolts in a specific sequence.
3) Notes about cleaning parts and using new gaskets when installing the cylinder head.
This document provides instructions for removing and installing a flywheel housing on a C18 Industrial Engine WJB. It is a 3-page service manual excerpt that describes:
1) Required tools and safety notices
2) Removal procedure which includes supporting the engine, removing bolts and lifting the housing off
3) Installation procedure which includes cleaning, applying sealant, positioning the housing and tightening bolts in a specific sequence and torque.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
This document provides disassembly and assembly instructions for a C18 industrial engine pump drive. It describes in detail how to disassemble and assemble the integral pump drive of a CX38-P892 petroleum transmission. The 19 step disassembly procedure includes removing bolts, gears, bearings, seals and other components. The 23 step assembly procedure describes cleaning parts and installing components in reverse order, paying attention to torque specifications and end play measurements. Tools required include lifting devices, pullers, indicators and other specialized tools.
1) The document provides disassembly and assembly instructions for removing and installing various components of a C18 industrial engine, including the power take-off drive group, vibration damper and pulley, crankshaft front seal, and front cover.
2) The instructions include lists of required tools and step-by-step procedures describing how to remove and install each component, with illustrations showing the parts.
3) Safety and cleaning notes are provided throughout to keep parts clean and avoid damage during disassembly and assembly.
The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including:
- Fuel priming pump removal and installation procedures in 3 steps.
- Fuel filter base removal procedure in 5 steps and disassembly procedure in 4 steps.
- Fuel filter base assembly procedure in 4 steps and installation procedure in 6 steps.
- Fuel transfer pump removal procedure in 6 steps and installation procedure in 7 steps.
- Electronic unit injector removal procedure with 5 steps requiring identification marks for installation.
Caterpillar cat 349 d l excavator (prefix gkf) service repair manual (gkf0000...fjjseksxckmdme
The document provides instructions for removing a travel motor and final drive from an excavator. It lists the required tools which include blocks, a hydraulic torque wrench assembly, link brackets, and cautions to contain fluids. The procedure describes attaching a lifting device to the travel motor and removing bolts and hose assemblies to detach the travel motor from the excavator.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR JAR
Configuration: ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06931709
Gear Group (Rear) - Remove and Install
SMCS - 1206-010; 1212-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp. 1
B 1P-0510 Driver Gp 1
Start By:
a. Remove the electric starting motor.
b. Remove the flywheel.
1. Support the engine.
1/10
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g06002548
2. Remove bolts (2) and rear crankshaft seal (1).
Illustration 2 g06002556
3. Remove bolts (4) and the washers. Remove cover (3) and the seal.
Illustration 3 g06002558
4. Remove gear (7), bolts (6), and gear (5).
Illustration 4 g06002564
2/10
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 5. Remove O-ring seal (8) from gear (7).
Illustration 5 g06172622
6. Use Tooling (A) to remove bushing (7A) from gear assembly (7).
Illustration 6 g06172537
7. Remove bolts (9), adapter assembly (10), and the O-ring seal.
Illustration 7 g06172541
8. Use Tooling (B) to remove bearing (11) from adapter assembly (10).
3/10
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Table 2
Required Tools
Tool Part Number Part Description Qty
A 095-0706 Bolt 2
Illustration 11 g06172557
Illustration 12 g06172580
5/10
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 13 g06172587
1. Lower the temperature of bearing (14). Be sure to match Dimension (B) and Dimension (C)
when installing bearing (14.). Dimension (B) indicates the angle of the joint on bearing (14).
Dimension (B) is 15° ± 1°. Dimension (C) shows the distance from bearing (14) to the end
of the bore. Dimension (C) is 4.000 ± 0.500 mm (0.1575 ± 0.0197 inch).
Illustration 14 g06172554
2. Install the O-ring seal and cover (9).
6/10
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g06172597
3. Install gear assembly (12) with oil passage plug (12A) facing out.
Illustration 16 g06172601
Illustration 17 g06172609
4. Lower the temperature of bearing (11). Be sure to match Dimension (F) and Dimension (G)
when installing bearing (11) into adapter assembly (10). Dimension (F) indicates the angle
of the joint on bearing (11). Dimension (F) is 15° ± 1°. Dimension (G) shows the distance
from bearing (11) to the end of the bore. Dimension (G) is 3.500 ± 0.500 mm
(0.1378 ± 0.0197 inch).
7/10
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 18 g06172537
5. Install the O-ring seal, adapter assembly (10), and bolts (9).
Illustration 19 g06172619
6. Lower the temperature of bearing (7A). Install bearing (7A) into gear assembly (7). Be sure
that each relief (H) is within 2° of each relief in gear assembly (7).
Illustration 20 g06002564
7. Install O-ring seal (8) onto gear (7).
8/10
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 21 g06002578
8. Install gear (5) and bolts (6).
Note: Tooling (A) is for supporting gear (7) during the installation of the cover and the rear
crankshaft seal.
Note: The bolt holes in gear (7) are not symmetrical. When installing Tooling (C), check
the rest of the bolts holes in gear (7) are aligned with the holes in the crankshaft.
9. Install gear (7) and Tooling (C).
Illustration 22 g06002581
10. Install cover (3), the seal, bolts (4), and the washers.
9/10
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g06002592
11. Install rear crankshaft seal (1) and bolts (2).
12. Remove Tooling (C).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 09:05:39 UTC+0800 2020
10/10
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00)...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR JAR
Configuration: ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249234
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B FT2712 Guide Stud 1
1/2
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g01132214
1. Attach Tooling (A) and a suitable lifting device to flywheel (2). The weight of flywheel (2)
is approximately 79 kg (175 lb).
2. Remove top bolt (1). Install Tooling (B).
3. Remove remaining bolts (1).
4. Remove flywheel (2).
5. Use a hammer and a punch in order to remove the ring gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 09:06:35 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR JAR
Configuration: ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06123534
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7574 Link Bracket 1
B FT2712 Guide Stud 1
C - Loctite 242 1
Always wear protective gloves when handling parts that have been
heated.
1. Raise the temperature of the ring gear. Position the ring gear with the part number toward
the crankshaft. Install the ring gear on the flywheel. Allow the ring gear to cool. Use a soft
hammer in order to seat the ring gear against the shoulder of the flywheel.
1/2
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g01132214
2. Attach Tooling (A) and a suitable lifting device to flywheel (2) . The weight of flywheel (2)
is approximately 79 kg (175 lb).
3. Position flywheel (2) on Tooling (B) .
4. Apply Tooling (C) to bolts (1) .
5. Install bolts (1) . Remove Tooling (B) . Install remaining bolt (1) . Tighten the bolts evenly
to a torque of 300 ± 40 N·m (221 ± 30 lb ft).
6. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect" for the
correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 09:07:32 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR JAR
Configuration: ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06010889
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01132235
1. Remove bolts (1).
2. Remove crankshaft rear seal (2).
Note: Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual Inspection and
Magnetic Particle Inspection" for the correct inspection procedure of the crankshaft seal surface.
Note: Refer to Reuse and Salvage Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9,
C-9, C10, C11, C12, C-12, C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the
correct specifications of the crankshaft.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 09:08:29 UTC+0800 2020
2/2
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR JAR
Configuration: ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i06010890
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 Primer N -
B - Loctite 620 Retaining Compound -
C 147-2675 Wear Sleeve Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g01140085
Illustration 2 g03698745
Numerical tightening sequence for bolts (2).
Note: If required, install a crankshaft wear sleeve at engine overhaul. For more information
please refer to the following Reuse and Salvage Guidelines. Refer to Reuse and Salvage
Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9, C-9, C10, C11, C12, C-12,
2/3
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the correct specifications
of the crankshaft. Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual
Inspection and Magnetic Particle Inspection" for the correct inspection procedure of the
crankshaft seal surface.
1. If a crankshaft wear sleeve is necessary, refer to Step 1.a through Step 1.d to install the
crankshaft wear sleeve. If a crankshaft wear sleeve is not necessary, refer to Step 2.
a. Clean and polish the crankshaft of imperfections.
b. Use Tooling (A) to clean the outside diameter of the crankshaft and the inside
diameter of the crankshaft wear sleeve.
c. Apply Tooling (B) to the outside diameter of the crankshaft and the inside diameter of
the crankshaft wear sleeve.
d. Use Tooling (C) to install the crankshaft wear sleeve.
Note: Leave the shipping sleeve in place to install the crankshaft rear seal. The crankshaft
rear seal must be installed dry.
Note: If the seal group, O-ring seal, and the shipping sleeve are separated, these
components should not be used.
2. Lubricate the O-ring seal with clean engine oil that is on the back of the crankshaft rear seal
(1).
3. Position crankshaft rear seal (1) and the shipping sleeve over the crankshaft. Push
crankshaft rear seal (1) in place to dislodge the shipping sleeve.
Note: Do not remove the shipping sleeve until bolts (2) are installed.
4. Install new bolts (2) hand tight. Then, tighten bolts (2) in numerical sequence, shown in
Illustration 2. Tighten bolts (2) to a torque of 12 ± 3 N·m (106 ± 27 lb in).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 09:09:26 UTC+0800 2020
3/3
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR JAR
Configuration: ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249340
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
b. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
1. Support the engine.
Illustration 1 g01132273
1/3
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2)
is approximately 62 kg (137 lb).
3. Remove bolts (1) and flywheel housing (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-8846 Gasket Sealant 1
1. Apply Tooling (A) to the face of the cylinder block.
Illustration 2 g01132273
2. Attach a suitable lifting device to flywheel housing (2). The weight of flywheel housing (2)
is approximately 62 kg (137 lb). Position flywheel housing (2) on the rear of the cylinder
block.
3. Install bolts (1).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Mon Jul 20 09:10:23 UTC+0800 2020
2/3
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 345C EXCAVATOR JAR
Configuration: ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)
Disassembly and Assembly
C11 and C13 Engines for Caterpillar Built Machines
Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018
i02249982
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
1/3
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g01132580
1. Remove belt (1).
2. Attach a suitable lifting device to crankshaft vibration damper and pulley (3). The weight of
crankshaft vibration damper and pulley (3) is approximately 27 kg (60 lb). Remove bolts
(2).
3. Remove crankshaft vibration damper and pulley (3).
Installation Procedure
2/3
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 2 g01132580
1. Attach a suitable lifting device to crankshaft vibration damper and pulley (3). The weight of
crankshaft vibration damper and pulley (3) is approximately 27 kg (60 lb). Position
crankshaft vibration damper and pulley (3) on the engine.
2. Install bolts (2).
3. Install belt (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 09:11:20 UTC+0800 2020
3/3
ISJ HEX COMMONALITY CHART JAR00001-UP (MACHINE)(SEBP5600 - 00) - ...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...