This document provides instructions to disassemble a 336F and 336F L excavator travel motor. It outlines 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, various plugs, seals, springs, relief valves, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, retaining ring pliers, bearing puller group, and other hardware. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 336 f excavator (prefix lcl) service repair manual (lcl00001 ...fjsqazkekdmme
This document provides instructions to disassemble a 336F and 336F L excavator travel motor. It lists the required tools and describes 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal components. Marks should be made on components to ensure proper reassembly. Care is needed when removing parts to avoid damage and release of stored spring forces.
Caterpillar cat 336 f l excavator (prefix lcl) service repair manual (lcl0000...fjsqazkekdmme
This document provides instructions to disassemble a 336F and 336F L excavator travel motor. It lists the required tools and describes 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal components. Marks should be made on components to ensure proper reassembly. Care is needed when removing parts to avoid damage and release of stored spring forces.
Caterpillar Cat 336F L Excavator (Prefix KFT) Service Repair Manual (KFT00001...djdksmmdmd
The document provides instructions for disassembling a 336F LN excavator travel motor. It lists 27 steps to completely disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and various bolts, pins and seals. Safety precautions are provided to release spring forces and contain fluids.
The document provides instructions for disassembling a 336F excavator travel motor. It describes 27 steps to remove components such as the motor head, springs, seals, relief valves, plugs and ball bearings. Tools include a transmission repair stand, lifting eye assembly, driver group and retaining ring pliers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 336 f ln excavator (prefix kft) service repair manual (kft000...fjsjekkdmnem
The document provides instructions for disassembling a 336F LN excavator travel motor. It describes 27 steps to remove components such as the motor head assembly, springs, seals, relief valves, plugs and bolts. Various tools are required including a driver group, retaining ring pliers, bearing puller group and eyebolt for lifting components. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix KFT) Service Repair Manu...f8uejkdkdmm3e
The document provides instructions for disassembling a 336F excavator travel motor. It describes 27 steps to remove components such as the motor head, springs, seals, relief valves, plugs and ball bearings. Tools include a transmission repair stand, lifting eye assembly, driver group and retaining ring pliers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 336 f ln excavator (prefix kft) service repair manual (kft000...fhhjsjekmdme
The document provides instructions for disassembling a 336F LN excavator travel motor. It lists 27 steps to completely disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and various bolts, pins and seals. Safety precautions are provided to release spring forces and contain fluids.
Caterpillar cat 336 f l excavator (prefix kft) service repair manual (kft0000...didkkmmdm
The document provides instructions for disassembling a 336F excavator travel motor. It describes 27 steps to remove components such as the motor head, springs, seals, relief valves, plugs and ball bearings. Tools include a transmission repair stand, lifting eye assembly, driver group and retaining ring pliers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 336 f excavator (prefix lcl) service repair manual (lcl00001 ...fjsqazkekdmme
This document provides instructions to disassemble a 336F and 336F L excavator travel motor. It lists the required tools and describes 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal components. Marks should be made on components to ensure proper reassembly. Care is needed when removing parts to avoid damage and release of stored spring forces.
Caterpillar cat 336 f l excavator (prefix lcl) service repair manual (lcl0000...fjsqazkekdmme
This document provides instructions to disassemble a 336F and 336F L excavator travel motor. It lists the required tools and describes 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal components. Marks should be made on components to ensure proper reassembly. Care is needed when removing parts to avoid damage and release of stored spring forces.
Caterpillar Cat 336F L Excavator (Prefix KFT) Service Repair Manual (KFT00001...djdksmmdmd
The document provides instructions for disassembling a 336F LN excavator travel motor. It lists 27 steps to completely disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and various bolts, pins and seals. Safety precautions are provided to release spring forces and contain fluids.
The document provides instructions for disassembling a 336F excavator travel motor. It describes 27 steps to remove components such as the motor head, springs, seals, relief valves, plugs and ball bearings. Tools include a transmission repair stand, lifting eye assembly, driver group and retaining ring pliers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 336 f ln excavator (prefix kft) service repair manual (kft000...fjsjekkdmnem
The document provides instructions for disassembling a 336F LN excavator travel motor. It describes 27 steps to remove components such as the motor head assembly, springs, seals, relief valves, plugs and bolts. Various tools are required including a driver group, retaining ring pliers, bearing puller group and eyebolt for lifting components. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix KFT) Service Repair Manu...f8uejkdkdmm3e
The document provides instructions for disassembling a 336F excavator travel motor. It describes 27 steps to remove components such as the motor head, springs, seals, relief valves, plugs and ball bearings. Tools include a transmission repair stand, lifting eye assembly, driver group and retaining ring pliers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar cat 336 f ln excavator (prefix kft) service repair manual (kft000...fhhjsjekmdme
The document provides instructions for disassembling a 336F LN excavator travel motor. It lists 27 steps to completely disassemble the travel motor, removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Tools required include a transmission repair stand, lifting eye assembly, driver group, and various bolts, pins and seals. Safety precautions are provided to release spring forces and contain fluids.
Caterpillar cat 336 f l excavator (prefix kft) service repair manual (kft0000...didkkmmdm
The document provides instructions for disassembling a 336F excavator travel motor. It describes 27 steps to remove components such as the motor head, springs, seals, relief valves, plugs and ball bearings. Tools include a transmission repair stand, lifting eye assembly, driver group and retaining ring pliers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001...f8uesjdkdmdm
The document provides instructions for installing a hydraulic lockout control on an excavator. It describes:
1) Installing the hydraulic lockout control using bolts and securing a switch.
2) Installing a panel and screws to cover the components.
3) The document contains detailed step-by-step instructions and illustrations for assembling and disassembling various components of an excavator such as a piston motor and fan. Safety warnings are provided throughout.
This document provides assembly instructions for repairing the transmission of a 329DL excavator. It consists of 52 steps to assemble the transmission components in the correct order, including installing gaskets, bearings, pistons, seals, covers, and other parts into the pump housing. Precautions are provided for steps involving spring tension. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
This document provides instructions for disassembling and assembling the recoil spring on a 329D L excavator. It describes:
1. The required tools and sockets for disassembly and assembly.
2. The disassembly procedure which involves using a special recoil spring bench tool to safely compress the spring and remove components.
3. The assembly procedure which again uses the bench tool to compress the spring and measure its length during assembly. Proper spring length is critical.
This document provides repair instructions for a 329DL excavator transmission. It outlines 38 steps to disassemble and reassemble the transmission, including instructions to clean parts, replace seals and O-rings, measure bearing clearance using shims, and install various transmission components like gears, seals, and housing pieces. Special tools are required for tasks like installing duo-cone seals and bearing surfaces must be coated with anti-seize compound before assembly.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...f8uesjdkdmdm
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix RGA) Service Repair Manual...f8uesjdkdmdm
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, springs, and valves in the proper sequence.
3. Lifting the swing motor or drive using lifting brackets and removing bolts to separate the components.
Caterpillar Cat 326D2 L Excavator (Prefix KER) Service Repair Manual (KER0000...f8uesjdkdmdm
This document provides the disassembly procedure for a travel motor in 27 steps. It begins by cleaning the outside of the travel motor and fastening it vertically. The first steps include removing the head and various internal components like seals, springs, plates, and pistons. Later steps dismantle the rotating assembly, remove bearings from the shaft, and disassemble the barrel assembly. Throughout, care is taken to mark components for reinstallation in their original positions. Required tools are also listed.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...f8uesjdkdmdm
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing supports and clamps, and disconnecting tubes and hoses to remove the cylinder head.
3. Installing a new gasket and torquing bolts to specified values to install the cylinder head. Reconnecting all tubes, hoses and harness assemblies.
1. The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine.
2. The removal procedure includes disconnecting harness assemblies, removing bolts, and draining coolant from the cooling system.
3. The installation procedure specifies applying anti-seize compound to bolts and tightening them in a numerical sequence to the specified torques. Connecting harness assemblies and installing supports are also described.
Caterpillar Cat 326D2 L (Prefix KGY) Service Repair Manual (KGY00001 and up).pdff8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
This document provides instructions for disassembling a travel motor. It begins by having the technician clean and secure the travel motor vertically. They are instructed to mark the head and body for alignment during reassembly. Over 25 steps are then outlined to remove various components of the travel motor like the head, brake piston, plates, and barrel assembly. Throughout, technicians are warned to be careful not to damage parts and ensure components are reinstalled in their original positions.
The document provides the disassembly procedure for a travel motor in 27 steps. It begins by removing the travel motor and cleaning it. Key steps include removing the head, brake piston, friction plates, and rotating assembly. The rotating assembly contains a shaft that requires removing retaining rings and bearing races using various tools. Piston assemblies are also removed from the barrel assembly after marking their positions.
Caterpillar Cat 325D L EXCAVATOR (Prefix T2S) Service Repair Manual (T2S00001...f8uesjdkdmdm
The document provides instructions to disassemble a final drive for a 325D L excavator. Key steps include:
1. Cleaning and marking the final drive assembly.
2. Removing the cover and gears using various tools.
3. Taking apart the carrier assemblies by removing pins, washers, and gears.
4. Using presses and hammers to separate additional components from the housing.
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdff8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavator models. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, seals and housing cover. Corresponding assembly instructions are also provided, specifying the use of various tools and noting that all seals and gaskets must be replaced. Cleanliness is emphasized throughout the assembly process.
The document provides step-by-step instructions to disassemble a final drive on an excavator. It begins by removing the final drive from the machine and securing it to a repair stand. Various components like gears, shafts, seals and housings are then removed individually using an assortment of tools. Detailed illustrations accompany each step to show how to properly disassemble the final drive. Cleanliness is emphasized to prevent dirt from entering the mechanism during reassembly.
Caterpillar Cat 325D L Excavator (Prefix SCR) Service Repair Manual (SCR00001...f8uesjdkdmdm
The document provides instructions for removing and installing a lifter group on a Caterpillar C7 engine. It describes disconnecting related components like the rocker arms and pushrods. It then instructs removing bolts and side covers to access the lifter arms and shaft. Identification marks should be made on each lifter before removal to ensure proper reinstallation.
Caterpillar Cat 325D L Excavator (Prefix NAC) Service Repair Manual (NAC00001...f8uesjdkdmdm
This service repair manual provides instructions for repairing a 325D L excavator transmission. It details 33 steps for disassembling and assembling the transmission components. Cleanliness is important during repair. O-rings and seals should always be replaced. Various tools are used to install bearings, seals, gears, and other parts in the correct order. Proper torque specifications and safety precautions are noted throughout the process.
Caterpillar Cat 325D L Excavator (Prefix LAL) Service Repair Manual (LAL00001...f8uesjdkdmdm
This document provides the disassembly procedure for a 325D L excavator travel motor. It lists the required tools and gives step-by-step instructions to disassemble the various components of the travel motor. Some key steps include removing the head from the motor body, extracting the brake piston, removing plates and discs, and taking apart the rotating assembly. Proper cleaning and replacement of seals is emphasized for reassembly.
Caterpillar Cat 325D L Excavator (Prefix MCL) Service Repair Manual (MCL00001...f8uesjdkdmdm
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Fasten the final drive assembly to a repair stand and remove the cover by taking out bolts and setscrews.
2) Remove additional components from the cover including a gear, check plate, and seals.
3) Clean all components thoroughly before disassembly to prevent dirt from entering during reassembly.
Caterpillar Cat 330D L Excavator (Prefix B6H) Service Repair Manual (B6H00001...f8uesjdkdmdm
The document provides instructions for installing a hydraulic lockout control on an excavator. It describes:
1) Installing the hydraulic lockout control using bolts and securing a switch.
2) Installing a panel and screws to cover the components.
3) The document contains detailed step-by-step instructions and illustrations for assembling and disassembling various components of an excavator such as a piston motor and fan. Safety warnings are provided throughout.
This document provides assembly instructions for repairing the transmission of a 329DL excavator. It consists of 52 steps to assemble the transmission components in the correct order, including installing gaskets, bearings, pistons, seals, covers, and other parts into the pump housing. Precautions are provided for steps involving spring tension. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
This document provides instructions for disassembling and assembling the recoil spring on a 329D L excavator. It describes:
1. The required tools and sockets for disassembly and assembly.
2. The disassembly procedure which involves using a special recoil spring bench tool to safely compress the spring and remove components.
3. The assembly procedure which again uses the bench tool to compress the spring and measure its length during assembly. Proper spring length is critical.
This document provides repair instructions for a 329DL excavator transmission. It outlines 38 steps to disassemble and reassemble the transmission, including instructions to clean parts, replace seals and O-rings, measure bearing clearance using shims, and install various transmission components like gears, seals, and housing pieces. Special tools are required for tasks like installing duo-cone seals and bearing surfaces must be coated with anti-seize compound before assembly.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix THW) Service Repair Manual...f8uesjdkdmdm
The document provides instructions for removing and installing a flywheel on a C7.1 engine. It describes:
1) Removing the bolts and electric starting motor to access the flywheel.
2) Installing guide studs and using lifting equipment to remove the flywheel.
3) Inspecting the flywheel and removing the ring gear if needed.
4) Cleaning and preparing the surfaces, then installing the flywheel using lifting equipment and guide studs, and tightening the bolts to the specified torque.
Caterpillar Cat 329D2 and 329D2L Excavator (Prefix RGA) Service Repair Manual...f8uesjdkdmdm
The document provides instructions for disassembling and assembling a swing motor and swing drive. Key steps include:
1. Cleaning all parts thoroughly before assembly and applying a light film of hydraulic oil.
2. Using retaining ring pliers to install a retaining ring and assembling plates, pistons, springs, and valves in the proper sequence.
3. Lifting the swing motor or drive using lifting brackets and removing bolts to separate the components.
Caterpillar Cat 326D2 L Excavator (Prefix KER) Service Repair Manual (KER0000...f8uesjdkdmdm
This document provides the disassembly procedure for a travel motor in 27 steps. It begins by cleaning the outside of the travel motor and fastening it vertically. The first steps include removing the head and various internal components like seals, springs, plates, and pistons. Later steps dismantle the rotating assembly, remove bearings from the shaft, and disassemble the barrel assembly. Throughout, care is taken to mark components for reinstallation in their original positions. Required tools are also listed.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...f8uesjdkdmdm
The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine. Key steps include:
1. Removing bolts and disconnecting harness assemblies to remove the valve mechanism cover base.
2. Draining coolant, removing supports and clamps, and disconnecting tubes and hoses to remove the cylinder head.
3. Installing a new gasket and torquing bolts to specified values to install the cylinder head. Reconnecting all tubes, hoses and harness assemblies.
1. The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine.
2. The removal procedure includes disconnecting harness assemblies, removing bolts, and draining coolant from the cooling system.
3. The installation procedure specifies applying anti-seize compound to bolts and tightening them in a numerical sequence to the specified torques. Connecting harness assemblies and installing supports are also described.
Caterpillar Cat 326D2 L (Prefix KGY) Service Repair Manual (KGY00001 and up).pdff8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 326D2 excavator. It lists the required tools and gives step-by-step procedures to remove and install various components of the travel motor such as the head, bearings, brake piston, seals, and housing covers. Special care must be taken when handling springs or installing seals to avoid injury. All components must be cleaned thoroughly before assembly and lubricated with oil during reassembly.
This document provides instructions for disassembling a travel motor. It begins by having the technician clean and secure the travel motor vertically. They are instructed to mark the head and body for alignment during reassembly. Over 25 steps are then outlined to remove various components of the travel motor like the head, brake piston, plates, and barrel assembly. Throughout, technicians are warned to be careful not to damage parts and ensure components are reinstalled in their original positions.
The document provides the disassembly procedure for a travel motor in 27 steps. It begins by removing the travel motor and cleaning it. Key steps include removing the head, brake piston, friction plates, and rotating assembly. The rotating assembly contains a shaft that requires removing retaining rings and bearing races using various tools. Piston assemblies are also removed from the barrel assembly after marking their positions.
Caterpillar Cat 325D L EXCAVATOR (Prefix T2S) Service Repair Manual (T2S00001...f8uesjdkdmdm
The document provides instructions to disassemble a final drive for a 325D L excavator. Key steps include:
1. Cleaning and marking the final drive assembly.
2. Removing the cover and gears using various tools.
3. Taking apart the carrier assemblies by removing pins, washers, and gears.
4. Using presses and hammers to separate additional components from the housing.
Caterpillar Cat 326D2 (Prefix KGY) Service Repair Manual (KGY00001 and up).pdff8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavator models. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, seals and housing cover. Corresponding assembly instructions are also provided, specifying the use of various tools and noting that all seals and gaskets must be replaced. Cleanliness is emphasized throughout the assembly process.
The document provides step-by-step instructions to disassemble a final drive on an excavator. It begins by removing the final drive from the machine and securing it to a repair stand. Various components like gears, shafts, seals and housings are then removed individually using an assortment of tools. Detailed illustrations accompany each step to show how to properly disassemble the final drive. Cleanliness is emphasized to prevent dirt from entering the mechanism during reassembly.
Caterpillar Cat 325D L Excavator (Prefix SCR) Service Repair Manual (SCR00001...f8uesjdkdmdm
The document provides instructions for removing and installing a lifter group on a Caterpillar C7 engine. It describes disconnecting related components like the rocker arms and pushrods. It then instructs removing bolts and side covers to access the lifter arms and shaft. Identification marks should be made on each lifter before removal to ensure proper reinstallation.
Caterpillar Cat 325D L Excavator (Prefix NAC) Service Repair Manual (NAC00001...f8uesjdkdmdm
This service repair manual provides instructions for repairing a 325D L excavator transmission. It details 33 steps for disassembling and assembling the transmission components. Cleanliness is important during repair. O-rings and seals should always be replaced. Various tools are used to install bearings, seals, gears, and other parts in the correct order. Proper torque specifications and safety precautions are noted throughout the process.
Caterpillar Cat 325D L Excavator (Prefix LAL) Service Repair Manual (LAL00001...f8uesjdkdmdm
This document provides the disassembly procedure for a 325D L excavator travel motor. It lists the required tools and gives step-by-step instructions to disassemble the various components of the travel motor. Some key steps include removing the head from the motor body, extracting the brake piston, removing plates and discs, and taking apart the rotating assembly. Proper cleaning and replacement of seals is emphasized for reassembly.
Caterpillar Cat 325D L Excavator (Prefix MCL) Service Repair Manual (MCL00001...f8uesjdkdmdm
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Fasten the final drive assembly to a repair stand and remove the cover by taking out bolts and setscrews.
2) Remove additional components from the cover including a gear, check plate, and seals.
3) Clean all components thoroughly before disassembly to prevent dirt from entering during reassembly.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L EXCAVATOR LCL
Configuration: 336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i03863290
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 by 250 mm (10 inch) Threaded Rod 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the travel motor.
1. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
1/10
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. 2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
3. Remove bolts (1).
4. Remove head (2) from the body of the travel motor.
2/10
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g00887302
5. Remove O-ring seal (3), port plate (4), and bearing (5).
Illustration 3 g00887311
6. Remove O-ring seals (6). Remove springs (7).
Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B).
3/10
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 7. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
8. Remove seal (9) and backup ring (10) from the brake piston.
9. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
10. Remove plates (13) and friction discs (14).
4/10
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 8 g02107957
Illustration 9 g00887405
Illustration 10 g00887424
11. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
12. Remove Tooling (C) from shaft (15).
13. Remove shaft (15) from rotating assembly (16).
Illustration 11 g00887426
5/10
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 14. Use Tooling (D) in order to remove retaining ring (17) from shaft (15).
Illustration 12 g00887445
15. Use a suitable press in order to remove bearing race (18) from shaft (15).
Illustration 13 g00887463
16. Rotate shaft (15). Use a suitable press and tooling (E) in order to remove bearing race (19)
from shaft (15).
Illustration 14 g00887501
17. Remove cam plate (20) from barrel assembly (21).
6/10
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 15 g00887520
18. Remove piston assemblies and retainer plate (22) from barrel assembly (21).
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g00887558
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Remove ball (23) and springs (24).
7/10
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 17 g02107975
20. Remove bearing (25).
21. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
22. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27).
23. Remove lip seal (28).
Illustration 19 g00887619
24. Remove bolts (29) and cover (30).
8/10
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 20 g00887729
25. Remove seal (31) and backup ring (32).
Illustration 21 g00887754
26. Remove piston actuator (33) and seal (34).
Illustration 22 g00887762
27. Remove O-ring seal (35) from the housing of the travel motor.
9/10
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L EXCAVATOR LCL
Configuration: 336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07195340
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 421-5662 Lifting Eye Assembly 1
C
6V-5215 M8 X 1.25 X 16 MM Bolt 2
9M-1974 M8 Hard Washer 2
D 1P-0510 Driver Gp 1
Start By:
a. Remove travel motor.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/14
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g06249277
1. Fasten travel motor (1) in a vertical position on Tooling (A). The weight of travel motor (1)
is approximately 82 kg (180 lb).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2. Remove bolts (2) and cap (3).
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
2/14
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 2 g06249309
Illustration 3 g06249323
Illustration 4 g06249325
3. Remove bolts (4) and cap (5).
4. Remove spring (6), spring (9), spool assembly (8), and spring seats (7).
3/14
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 5 g06249329
5. Remove plug (11), relief valve (10), and the O-ring seals.
Illustration 6 g06249334
6. Remove plug (13), relief valve (12), and the O-ring seals.
Illustration 7 g06249337
7. Remove plug (14), and the O-ring seal.
4/14
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 8 g06249341
Illustration 9 g06249344
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8. Remove plug (15), spool assembly (16), spring (17), and the O-ring seals.
5/14
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 10 g06249348
9. Remove plugs (18) and the O-ring seals.
Illustration 11 g06249351
10. Remove bolts (19).
Illustration 12 g06249354
11. Attach Tooling (B) and a suitable lifting device to motor head assembly (20). The weight of
motor head assembly (20) is approximately 27 kg (60 lb). Remove motor head assembly
(20).
6/14
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 13 g06250338
12. Remove the ball bearing that is located on the bottom side of motor head assembly (20).
Illustration 14 g06249364
Port plate (25) may still be adhered to the bottom of motor head assembly (20).
13. Remove O-ring seals (21), O-ring seal (22), springs (23), springs (24), and port plate (25).
Note: Note the location of springs (23). They must be installed in the same location during
the assembly procedure.
Illustration 15 g06249511
7/14
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 14. Insert Tooling (C) into piston assembly (26). Use a suitable prying device and Tooling (C)
to remove piston assembly (26).
Illustration 16 g06250418
15. Remove O-ring seal (27) and O-ring seal (28).
Illustration 17 g06249522
16. Use suitable prying devices to remove guide assembly (29).
Illustration 18 g06249535
17. Remove O-ring seal (30).
8/14
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 19 g06249539
Illustration 20 g06249544
18. Remove separator plates (31) and friction plates (32). Note the alternating order of separator
plates (31) and friction plates (32) for assembly purposes.
Illustration 21 g06249564
19. Remove barrel assembly (33).
Note: Do not allow the components of barrel assembly (33) to come apart while you
remove barrel assembly (33). The components of barrel assembly (33) must be reinstalled
into the original positions.
9/14
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 22 g06249598
Note: Mark the component locations for assembly purposes before you disassemble the
barrel assembly.
20. Remove piston assemblies (34) and retainer (35).
Illustration 23 g06249609
21. Remove hold down ball (36).
Illustration 24 g06249621
10/14
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. 22. Remove dowel pins (37).
Illustration 25 g06249657
23. Put location marks on swashplate (38) for assembly purposes. Remove swashplate (38).
Illustration 26 g06249682
24. Remove pistons (39) and the balls.
Illustration 27 g06249751
25. Remove springs (40).
11/14
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Illustration 28 g06249755
Illustration 29 g06249758
26. Use a suitable press and Tooling (D) to remove snap ring (41), spacers (42), and spring (43).
12/14
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 30 g06249760
27. Use a soft faced hammer to remove shaft assembly (44). Remove shaft assembly (44) in the
direction that is indicated by the arrow.
28. Remove O-ring seal (45).
Illustration 31 g06249762
29. Remove lip seal (46).
Illustration 32 g06249763
30. Use a suitable press to push shaft (47) out of bearing (48).
13/14
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engi...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L EXCAVATOR LCL
Configuration: 336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336F Excavator Machine Systems
Media Number -UENR0192-04 Publication Date -01/02/2018 Date Updated -21/02/2018
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
336F & 336F L Excavators LCL00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/6/9
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...