The document provides instructions for disassembling and assembling a travel motor. It is a 28 step process that includes removing parts like seals, bearings, and housing components. Precision is required to reinstall the springs, pistons, and other small parts correctly. The final steps are to install the motor housing cover and tighten the bolts to the specified torque.
Caterpillar cat 336 e excavator (prefix ked) service repair manual (ked00001 ...fjekkdmmem
The document provides instructions for assembling and disassembling components of an excavator travel motor and final drive. It consists of 28 steps to assemble the travel motor, beginning with installing o-rings and seals and ending with installing the motor head. 13 steps are listed to remove and install the final drive and travel motor assembly, including draining oil, removing hoses and bolts, and lifting out the assembly. 10 steps are then given to disassemble the final drive, starting with removing the cover bolts and ending by removing the sun gear, spacer, and planetary gears.
Caterpillar cat 336 e excavator (prefix ked) service repair manual (ked00001 ...fjjskekdm
The document provides instructions for assembling and disassembling components of an excavator travel motor and final drive. It consists of 28 steps to assemble the travel motor, beginning with installing o-rings and seals and ending with installing the motor head. It also includes 13 steps to remove the final drive and travel motor assembly, and 5 steps to install it, including applying thread locking compound to bolts and specified torque values.
Caterpillar cat 336 e l excavator (prefix ked) service repair manual (ked0000...fjsekqazxkdmmem
The document provides instructions for assembling and disassembling components of an excavator travel motor and final drive. It consists of 28 steps to assemble the travel motor, beginning with installing o-rings and seals and ending with installing the motor head. 13 steps are listed to remove and install the final drive and travel motor assembly, including draining oil, removing hoses and bolts, and lifting out the assembly. 10 steps are then given to disassemble the final drive, starting with removing the cover bolts and ending by removing the sun gear, spacer, and planetary gears.
Caterpillar cat 336 e l excavator (prefix ked) service repair manual (ked0000...fjskekmdm
The document provides instructions for assembling a travel motor. It involves 27 steps including installing seals, springs, pistons, bearings and other components in the proper order and orientation. The travel motor is then installed by attaching it to the final drive assembly using bolts and following markings to ensure correct alignment. Disassembly is reversed, removing hoses, bolts, seals and other parts, taking care when handling components due to weight and pressures.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...zatao0179249295
1. The document provides assembly instructions for installing a travel motor on an excavator. It involves 27 steps including installing seals, springs, pistons and other components into housings and covers in the proper order and orientation.
2. Tools required include an adapter, nuts, washers, threaded rod, eyebolt, various pliers, a driver group, bearing puller group, and Loctite.
3. Safety precautions are provided for spring loaded components and hydraulic system pressure.
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. The procedure includes disconnecting hoses, removing mounting bolts, and lifting out the assembly.
3. Disassembly instructions are given for a final drive, starting with removing the cover and plate using lifting tools. Detailed diagrams accompany each step.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...luanxianshi27
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. It describes removing hoses, fittings, bolts, and lifting the assembly to remove it. The procedure is reversed for installation.
3. Disassembly instructions are given for a final drive, including removing the cover, plate, and links using lifting brackets and forcing bolts. Detailed diagrams accompany each step.
1. The document provides assembly instructions for installing a travel motor on an excavator. It involves 27 steps including installing seals, springs, pistons and other components into housings and covers in the proper order and orientation.
2. Tools required include an adapter, nuts, washers, threaded rod, eyebolt, various pliers, a driver group, bearing puller group, and Loctite.
3. Safety precautions are provided for spring loaded components and hydraulic system pressure.
Caterpillar cat 336 e excavator (prefix ked) service repair manual (ked00001 ...fjekkdmmem
The document provides instructions for assembling and disassembling components of an excavator travel motor and final drive. It consists of 28 steps to assemble the travel motor, beginning with installing o-rings and seals and ending with installing the motor head. 13 steps are listed to remove and install the final drive and travel motor assembly, including draining oil, removing hoses and bolts, and lifting out the assembly. 10 steps are then given to disassemble the final drive, starting with removing the cover bolts and ending by removing the sun gear, spacer, and planetary gears.
Caterpillar cat 336 e excavator (prefix ked) service repair manual (ked00001 ...fjjskekdm
The document provides instructions for assembling and disassembling components of an excavator travel motor and final drive. It consists of 28 steps to assemble the travel motor, beginning with installing o-rings and seals and ending with installing the motor head. It also includes 13 steps to remove the final drive and travel motor assembly, and 5 steps to install it, including applying thread locking compound to bolts and specified torque values.
Caterpillar cat 336 e l excavator (prefix ked) service repair manual (ked0000...fjsekqazxkdmmem
The document provides instructions for assembling and disassembling components of an excavator travel motor and final drive. It consists of 28 steps to assemble the travel motor, beginning with installing o-rings and seals and ending with installing the motor head. 13 steps are listed to remove and install the final drive and travel motor assembly, including draining oil, removing hoses and bolts, and lifting out the assembly. 10 steps are then given to disassemble the final drive, starting with removing the cover bolts and ending by removing the sun gear, spacer, and planetary gears.
Caterpillar cat 336 e l excavator (prefix ked) service repair manual (ked0000...fjskekmdm
The document provides instructions for assembling a travel motor. It involves 27 steps including installing seals, springs, pistons, bearings and other components in the proper order and orientation. The travel motor is then installed by attaching it to the final drive assembly using bolts and following markings to ensure correct alignment. Disassembly is reversed, removing hoses, bolts, seals and other parts, taking care when handling components due to weight and pressures.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...zatao0179249295
1. The document provides assembly instructions for installing a travel motor on an excavator. It involves 27 steps including installing seals, springs, pistons and other components into housings and covers in the proper order and orientation.
2. Tools required include an adapter, nuts, washers, threaded rod, eyebolt, various pliers, a driver group, bearing puller group, and Loctite.
3. Safety precautions are provided for spring loaded components and hydraulic system pressure.
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. The procedure includes disconnecting hoses, removing mounting bolts, and lifting out the assembly.
3. Disassembly instructions are given for a final drive, starting with removing the cover and plate using lifting tools. Detailed diagrams accompany each step.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...luanxianshi27
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. It describes removing hoses, fittings, bolts, and lifting the assembly to remove it. The procedure is reversed for installation.
3. Disassembly instructions are given for a final drive, including removing the cover, plate, and links using lifting brackets and forcing bolts. Detailed diagrams accompany each step.
1. The document provides assembly instructions for installing a travel motor on an excavator. It involves 27 steps including installing seals, springs, pistons and other components into housings and covers in the proper order and orientation.
2. Tools required include an adapter, nuts, washers, threaded rod, eyebolt, various pliers, a driver group, bearing puller group, and Loctite.
3. Safety precautions are provided for spring loaded components and hydraulic system pressure.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...cnp692569
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly. 10 steps are outlined for removal, including draining oil, removing hoses and fittings, and using lifting tools. 13 steps are given for installation, with torque specifications for the reinstallation bolts.
3. Disassembly instructions for the final drive include removing the cover, plate, and links using lifting brackets and forcing bolts.
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. The procedure includes disconnecting hoses, removing mounting bolts, and lifting out the assembly.
3. Disassembly instructions are given for a final drive, including removing the cover, plate, and installing lifting brackets to remove internal components. Detailed diagrams accompany each step.
Caterpillar Cat 336E and 336E L Excavator (Prefix GTJ) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components. 13 steps are listed to remove the final drive and travel motor as a unit which include draining oil, removing hoses, bolts and the counterbalance valve. The installation procedure lists 3 steps which are to install in reverse order of removal, apply thread locking compound to bolts, and tighten to specified torques.
Caterpillar Cat 336E and 336E L Excavator (Prefix GTJ) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic lines before removal.
2) Using lifting equipment to remove the final drive and travel motor assembly, travel motor, and coupling.
3) Cleaning and lubricating parts before reverse installation and tightening bolts to specified torques.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing the final drive and travel motor assembly.
2) Attaching lifting equipment to remove the assembly, which weighs approximately 860 kg.
3) Separating the travel motor from the final drive by removing four bolts.
4) Reinstalling the components by reversing the removal steps and tightening bolts to the specified torques.
Caterpillar cat 336 e excavator (prefix gtj) service repair manual (gtj00001 ...fjjfyjsekdmme
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Removing hoses, fittings, covers and bolts to separate the final drive and travel motor assembly from the excavator frame.
2) Using lifting devices to remove the assembly and further disassemble the travel motor from the final drive.
3) The reverse process to reinstall the components, applying sealant and torquing bolts to specifications.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing bolts to separate the final drive and travel motor assembly from the frame.
2) Attaching lifting equipment to remove the assembly and travel motor, noting orientation marks for reinstallation.
3) Reinstalling the components by reversing the removal steps and tightening bolts to specified torques.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...jfskemsemm
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components. 13 steps are listed to remove the final drive and travel motor as a unit which include draining oil, removing hoses, bolts and the counterbalance valve. The installation procedure lists 3 steps which are installing the components in reverse order of removal while applying threadlock and torquing bolts to the specified values.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...fjkkekmdm
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing the final drive and travel motor assembly.
2) Attaching lifting equipment to remove the assembly, which weighs approximately 860 kg.
3) Separating the travel motor from the final drive by removing four bolts.
4) Reinstalling the components by reversing the removal steps and tightening bolts to the specified torques.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and securing it with mounting bolts. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new one. The procedures are separated into sections for engines with a 14-bolt housing assembly versus a 10-bolt housing assembly. Precise instructions are given for lubricating parts, inserting the seal, aligning components, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f7usuejkdkddm3
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and pressing the pulley onto the crankshaft during installation. Tightening specifications are included for attaching the pulley.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts, lifting the flywheel off, and potentially removing a ring gear. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and explains cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The steps are:
1. Use a drill bit to drill out the lock tabs of the seal.
2. Pry the seal out of the housing with a seal removal tool.
3. Inspect the seal bore and remove any debris before installing the new seal.
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, installing components like seals, spacers, washers, and plugs in reverse order of disassembly. Tools required are listed in tables. Cautions are provided about cleanliness, contamination, misassembly, and applying lubricant to parts.
More Related Content
Similar to Caterpillar Cat 336E Excavator (Prefix KED) Service Repair Manual (KED00001 and up).pdf
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...cnp692569
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly. 10 steps are outlined for removal, including draining oil, removing hoses and fittings, and using lifting tools. 13 steps are given for installation, with torque specifications for the reinstallation bolts.
3. Disassembly instructions for the final drive include removing the cover, plate, and links using lifting brackets and forcing bolts.
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. The procedure includes disconnecting hoses, removing mounting bolts, and lifting out the assembly.
3. Disassembly instructions are given for a final drive, including removing the cover, plate, and installing lifting brackets to remove internal components. Detailed diagrams accompany each step.
Caterpillar Cat 336E and 336E L Excavator (Prefix GTJ) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components. 13 steps are listed to remove the final drive and travel motor as a unit which include draining oil, removing hoses, bolts and the counterbalance valve. The installation procedure lists 3 steps which are to install in reverse order of removal, apply thread locking compound to bolts, and tighten to specified torques.
Caterpillar Cat 336E and 336E L Excavator (Prefix GTJ) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic lines before removal.
2) Using lifting equipment to remove the final drive and travel motor assembly, travel motor, and coupling.
3) Cleaning and lubricating parts before reverse installation and tightening bolts to specified torques.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing the final drive and travel motor assembly.
2) Attaching lifting equipment to remove the assembly, which weighs approximately 860 kg.
3) Separating the travel motor from the final drive by removing four bolts.
4) Reinstalling the components by reversing the removal steps and tightening bolts to the specified torques.
Caterpillar cat 336 e excavator (prefix gtj) service repair manual (gtj00001 ...fjjfyjsekdmme
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Removing hoses, fittings, covers and bolts to separate the final drive and travel motor assembly from the excavator frame.
2) Using lifting devices to remove the assembly and further disassemble the travel motor from the final drive.
3) The reverse process to reinstall the components, applying sealant and torquing bolts to specifications.
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing bolts to separate the final drive and travel motor assembly from the frame.
2) Attaching lifting equipment to remove the assembly and travel motor, noting orientation marks for reinstallation.
3) Reinstalling the components by reversing the removal steps and tightening bolts to specified torques.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...jfskemsemm
The document provides instructions for disassembling and assembling a travel motor and final drive. It describes 27 steps to assemble the travel motor which include installing seals, springs, pistons and other components. 13 steps are listed to remove the final drive and travel motor as a unit which include draining oil, removing hoses, bolts and the counterbalance valve. The installation procedure lists 3 steps which are installing the components in reverse order of removal while applying threadlock and torquing bolts to the specified values.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...fjkkekmdm
The document provides instructions for removing and installing a travel motor on an excavator. It describes:
1) Draining the final drive oil and disconnecting hydraulic hoses before removing the final drive and travel motor assembly.
2) Attaching lifting equipment to remove the assembly, which weighs approximately 860 kg.
3) Separating the travel motor from the final drive by removing four bolts.
4) Reinstalling the components by reversing the removal steps and tightening bolts to the specified torques.
Similar to Caterpillar Cat 336E Excavator (Prefix KED) Service Repair Manual (KED00001 and up).pdf (9)
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and securing it with mounting bolts. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new one. The procedures are separated into sections for engines with a 14-bolt housing assembly versus a 10-bolt housing assembly. Precise instructions are given for lubricating parts, inserting the seal, aligning components, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f7usuejkdkddm3
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and pressing the pulley onto the crankshaft during installation. Tightening specifications are included for attaching the pulley.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts, lifting the flywheel off, and potentially removing a ring gear. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and explains cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The steps are:
1. Use a drill bit to drill out the lock tabs of the seal.
2. Pry the seal out of the housing with a seal removal tool.
3. Inspect the seal bore and remove any debris before installing the new seal.
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, installing components like seals, spacers, washers, and plugs in reverse order of disassembly. Tools required are listed in tables. Cautions are provided about cleanliness, contamination, misassembly, and applying lubricant to parts.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f7usuejkdkddm3
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
The document provides assembly instructions for a 345C excavator final drive system. It involves assembling three carrier assemblies that contain planetary gears, installing them into a ring gear housing along with other components like bearing cones and seals. The procedure has 26 steps and requires various tools. It ensures proper bearing preload is achieved and components are cleaned, lubricated and torqued correctly during reassembly.
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E EXCAVATOR KED
Configuration: 336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15).
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15).
Note: Bearing race (18) must contact retaining ring (17).
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16).
17. Place the pump housing into Tooling (A).
6/10
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 14 g02107957
18. Use Tooling (C) to install rotating assembly (16) into the housing.
Illustration 15 g00887501
Illustration 16 g02107975
19. The notches in cam plate (20) must align with keys (26). The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
7/10
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. 20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8).
24. Install brake piston (8) into the housing so that the cast mark on brake piston (8) is aligned
with the brake supply passage in the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level to
prevent damage to the O-ring seals.
8/10
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6).
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5).
Illustration 22 g00887295
9/10
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 2 23:39:24 UTC+0800 2020
10/10
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E EXCAVATOR KED
Configuration: 336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i07191698
Final Drive and Travel Motor - Remove and Install
SMCS - 4050; 4351
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change" for the correct
draining and filling procedures.
1/5
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 1 g02108761
2. Remove bolts (1) and cover (2).
3. Separate the track.
Illustration 2 g02108762
4. Disconnect hose assemblies (3) ( 4), and (6). Remove fitting (5).
2/5
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 3 g02108781
5. Attach Tooling (A) and a suitable lifting device to final drive and travel motor (7). The
weight of final drive and travel motor (7) is approximately 860 kg (1896 lb). Put a slight
lifting tension on final drive and travel motor (7).
Illustration 4 g02108790
Note: Mark the orientation of the final drive and travel motor assembly for installation
purposes.
6. Remove bolts (8).
Illustration 5 g02108791
7. Use two bolts (8) to remove final drive and travel motor (7).
8. Carefully remove final drive and travel motor (7).
9. Remove bolts (8) from the frame.
3/5
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 6 g02108793
10. Remove bolts (9), counterbalance valve (10), and the O-ring seals.
Illustration 7 g02108794
11. Attach Tooling (B) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 84 kg (185 lb).
12. Remove four bolts (12) and travel motor (11) from final drive (13).
4/5
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 8 g02108914
13. Remove coupling (14).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
C - Loctite C5A Copper Anti-Seize -
1. Before assembly remove all compounds, oil, and dust.
2. Install final drive and travel motor (7) in the reverse order of removal.
a. Tighten bolts (9) to a torque of 80 ± 8 N·m (60 ± 6 lb ft).
b. Apply Tooling (C) to the threads of bolt (8).
c. Tighten bolts (8) to a torque of 250 ± 25 N·m (184 ± 18 lb ft) and turn an additional
angle of 45 ± 5 degrees. Refer to Service Magazine, M0083843, "An Improved Bolt
Tightening Procedure for the Critical Joints Is Now Used on All Excavators" for more
detail information.
d. Tighten hose assembly (3) to a torque of 160 ± 16 N·m (120 ± 12 lb ft).
e. Tighten bolts (1) to a torque of 130 ± 10 N·m (95 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 2 23:40:20 UTC+0800 2020
5/5
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E EXCAVATOR KED
Configuration: 336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i03885522
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 154-6183 Forcing Bolts 3
C 138-7576 Link Brackets 3
Start By:
a. Remove the final drive and the travel motor.
Illustration 1 g02131413
1/8
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 1. Attach Tooling (A) and a suitable lifting device to cover (2). The weight of cover (2) is
approximately 20 kg (45 lb). Remove bolts (1) and cover (2).
Illustration 2 g02131414
2. Remove plate (3) from cover (2).
Illustration 3 g02131415
3. Remove sun gear (4), spacer (5), and planetary gear assembly (6).
2/8
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 4 g02131875
4. Remove retaining ring (7), washer (8), planetary gear (9), roller bearing (11), and washer
(12) from carrier assembly (13).
5. Remove retaining ring (10) and sun gear (14) from carrier assembly (13).
Illustration 5 g02131876
6. Remove spacer (16).
7. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (15). The weight
of planetary gear assembly (15) is approximately 32 kg (70 lb). Remove planetary gear
assembly (15).
3/8
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 6 g02131877
8. Drive spring pin (17) into planetary shaft (18) with a suitable hammer and a suitable punch.
9. Remove planetary shaft (18), washer (20), roller bearing (20), planetary gear (23), and
washer (24) from the carrier assembly (21).
10. Remove spring pin (17) from planetary shaft (18) with a suitable hammer and a suitable
punch.
11. Remove retaining ring (19) and sun gear (25) from carrier assembly (21).
Illustration 7 g02131878
12. Remove spacer (26).
13. Attach Tooling (A) and a suitable lifting device to ring gear (27). The weight of ring gear
(27) is approximately 70 kg (155 lb). Remove bolts (28) and ring gear (27).
4/8
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 8 g02131879
14. Remove O-ring seal (29).
15. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (30). The weight
of planetary gear assembly (30) is approximately 57 kg (125 lb). Remove planetary gear
assembly (30).
Illustration 9 g02131881
16. Drive spring pin (31) into planetary shaft (32) with a suitable hammer and a suitable punch.
17. Remove planetary shaft (32), washer (33), roller bearings (35), planetary gear (36), and
washer (36) from the carrier assembly (34).
18. Remove spring pin (31) from planetary shaft (32) with a suitable hammer and a suitable
punch.
5/8
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 10 g02131882
Illustration 11 g02131885
19. Remove bolts (38). Use Tooling (B) in order to remove gear (39).
Illustration 12 g02131886
20. Remove shims (40).
6/8
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 13 g02131887
21. Attach Tooling (C) and a suitable lifting device to sprocket housing (41). The weight of
sprocket housing (41) is approximately 107 kg (235 lb). Remove sprocket housing (41) and
roller bearing (42).
Illustration 14 g02131888
22. Remove bearing races (43) and Duo-Cone seal (44) from sprocket housing (41).
7/8
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 15 g02132155
23. Remove Duo-Cone seal (45) and roller bearing (47) from motor housing (48). The weight of
motor housing (48) is approximately 91 kg (200 lb).
24. If necessary, remove dowels (46) from motor housing (48).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Aug 2 23:41:16 UTC+0800 2020
8/8
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E EXCAVATOR KED
Configuration: 336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i05103849
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 154-6183 Forcing Bolts 3
C 138-7576 Link Brackets 3
D 5P-3931 Anti-Seize Compound -
E 1U-9895 Crossblock 1
F 6V-2012 Depth Micrometer 1
G 6V-7059 Micrometer () 1
H - Loctite 242 -
J 6V-2055 Grease -
K - Loctite 17430 -
L 8T-9206 Seal Installer 1
1/12
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Illustration 1 g02132155
1. Apply Tooling (D) to the surface of dowels (46) . Install dowels (46) .
2. Raise the temperature of roller bearing (47) . Install the roller bearing (47) on motor housing
(48) .
3. Install Duo-Cone seal (45) .
Illustration 2 g02131888
4. Lower the temperature of bearing races (43) . Install bearing races (43) in sprocket housing
(41) .
5. Install Duo-Cone seal (44) .
2/12
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. Illustration 3 g02131887
6. Attach Tooling (C) and a suitable lifting device to sprocket housing (41) . The weight of
sprocket housing (41) is approximately 107 kg (235 lb). Install sprocket housing (41) .
7. Raise the temperature of roller bearing (42) . Install the roller bearing (42) .
Illustration 4 g02135728
3/12
336E & 336E L Excavators KED00001-UP (MACHINE) POWERED BY C9.3 Engin...
2020/8/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...