The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) for Caterpillar 336D2 and 336D2 L excavators. The disassembly procedure involves using various tools to remove 30 individual parts from the pump in a specific order. The assembly procedure similarly lists 30 steps to reinstall the parts in reverse order, noting requirements for cleaning, heating/cooling parts, and warnings about spring-loaded components.
Caterpillar Cat 336D L Excavator (Prefix PPN) Service Repair Manual (PPN00001...zatao0179249295
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of a 336D L & 336D LN excavator. The disassembly process involves removing 30 parts in 9 steps, taking care with springs that can cause injury. The assembly follows a 30 step process and refers to other documents for filling hydraulic fluid. Precise installation of bearings and seals is required using various specialty tools.
The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators. The procedures include 30 steps for assembling the pump and 7 steps for disassembling it. Tools required include retaining ring pliers, a dial indicator, and a bearing puller. Technicians are advised to clean all parts thoroughly before assembly and to replace any worn or damaged parts.
Caterpillar Cat 336D L Excavator (Prefix PPN) Service Repair Manual (PPN00001...kesi7153062
The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators. The procedures include 30 steps for assembling the pump and 7 steps for disassembling it. Tools required include retaining ring pliers, a dial indicator, and a bearing puller. Technicians are advised to clean all parts thoroughly before assembly and to replace any worn or damaged parts.
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) on Caterpillar 336D L and 336D LN excavators. The disassembly process involves removing 30 parts in 9 steps, taking care with springs that can propel parts, while the assembly follows 30 steps to reinstall all parts in the reverse order. Tools include retaining ring pliers, a dial indicator, and a bearing puller. The document emphasizes cleanliness during assembly and replacing any worn parts.
Caterpillar Cat 336D L Excavator (Prefix PPN) Service Repair Manual (PPN00001...cnp692569
The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators. The procedures include 30 steps for assembling the pump and 7 steps for disassembling it. Tools required include retaining ring pliers, a dial indicator, and a bearing puller. Technicians are advised to clean all parts thoroughly before assembly and to replace any worn or damaged parts.
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) on Caterpillar 336D L and 336D LN excavators. The disassembly process involves removing 30 parts in 9 steps, taking care with springs that can propel parts, while the assembly follows 30 steps to reinstall all parts in the reverse order. Tools include retaining ring pliers, a dial indicator, and a bearing puller. Cleanliness is important and worn parts should be replaced.
Caterpillar Cat 336D2 L Excavator (Prefix TLY) Service Repair Manual (TLY0000...zatao0179249295
The document provides instructions for disassembling and assembling a piston pump. It includes 30 steps for assembly, beginning with cleaning parts and ending with filling the hydraulic system with oil. The 3 steps for disassembly are: 1) removing bolts and the head, 2) removing internal seals and plates, and 3) removing pistons, bearings and other internal components. Tools include retaining ring pliers, a dial indicator, and a bearing puller. Safety precautions are provided for spring loaded parts.
The document provides instructions for disassembling and assembling a piston pump. It includes 30 steps for assembly, beginning with cleaning parts and ending by filling the hydraulic system with oil. Disassembly involves 8 steps, starting with removing the head and ending by removing pins from the barrel. Required tools include retaining ring pliers, a dial indicator, and a bearing puller. Safety precautions are provided throughout.
Caterpillar Cat 336D L Excavator (Prefix PPN) Service Repair Manual (PPN00001...zatao0179249295
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of a 336D L & 336D LN excavator. The disassembly process involves removing 30 parts in 9 steps, taking care with springs that can cause injury. The assembly follows a 30 step process and refers to other documents for filling hydraulic fluid. Precise installation of bearings and seals is required using various specialty tools.
The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators. The procedures include 30 steps for assembling the pump and 7 steps for disassembling it. Tools required include retaining ring pliers, a dial indicator, and a bearing puller. Technicians are advised to clean all parts thoroughly before assembly and to replace any worn or damaged parts.
Caterpillar Cat 336D L Excavator (Prefix PPN) Service Repair Manual (PPN00001...kesi7153062
The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators. The procedures include 30 steps for assembling the pump and 7 steps for disassembling it. Tools required include retaining ring pliers, a dial indicator, and a bearing puller. Technicians are advised to clean all parts thoroughly before assembly and to replace any worn or damaged parts.
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) on Caterpillar 336D L and 336D LN excavators. The disassembly process involves removing 30 parts in 9 steps, taking care with springs that can propel parts, while the assembly follows 30 steps to reinstall all parts in the reverse order. Tools include retaining ring pliers, a dial indicator, and a bearing puller. The document emphasizes cleanliness during assembly and replacing any worn parts.
Caterpillar Cat 336D L Excavator (Prefix PPN) Service Repair Manual (PPN00001...cnp692569
The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators. The procedures include 30 steps for assembling the pump and 7 steps for disassembling it. Tools required include retaining ring pliers, a dial indicator, and a bearing puller. Technicians are advised to clean all parts thoroughly before assembly and to replace any worn or damaged parts.
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) on Caterpillar 336D L and 336D LN excavators. The disassembly process involves removing 30 parts in 9 steps, taking care with springs that can propel parts, while the assembly follows 30 steps to reinstall all parts in the reverse order. Tools include retaining ring pliers, a dial indicator, and a bearing puller. Cleanliness is important and worn parts should be replaced.
Caterpillar Cat 336D2 L Excavator (Prefix TLY) Service Repair Manual (TLY0000...zatao0179249295
The document provides instructions for disassembling and assembling a piston pump. It includes 30 steps for assembly, beginning with cleaning parts and ending with filling the hydraulic system with oil. The 3 steps for disassembly are: 1) removing bolts and the head, 2) removing internal seals and plates, and 3) removing pistons, bearings and other internal components. Tools include retaining ring pliers, a dial indicator, and a bearing puller. Safety precautions are provided for spring loaded parts.
The document provides instructions for disassembling and assembling a piston pump. It includes 30 steps for assembly, beginning with cleaning parts and ending by filling the hydraulic system with oil. Disassembly involves 8 steps, starting with removing the head and ending by removing pins from the barrel. Required tools include retaining ring pliers, a dial indicator, and a bearing puller. Safety precautions are provided throughout.
Caterpillar Cat 336D2 L Excavator (Prefix TLY) Service Repair Manual (TLY0000...luanxianshi27
The document provides instructions for disassembling and assembling a piston pump. It includes 30 steps for assembly, beginning with cleaning parts and ending with filling the hydraulic system with oil. The 3 steps for disassembly are: 1) removing bolts and the head, 2) removing internal seals and plates, and 3) removing pistons, bearings and other internal components. Tools include retaining ring pliers, a dial indicator, and a bearing puller. Safety precautions are provided for spring loaded parts.
1. The document provides instructions for disassembling and assembling the piston pump of a 336D2 excavator.
2. It details 30 steps for assembly, including installing various parts like bearings, seals, springs, and fasteners.
3. Instructions are accompanied by illustrations and warnings about safety and cleanliness.
The document provides instructions for disassembling and assembling a piston pump. It includes 30 steps for assembly, beginning with cleaning parts and ending by filling the hydraulic system with oil. Disassembly involves 8 steps, starting with removing the head and ending by removing pins from the barrel. Required tools include retaining ring pliers, a dial indicator, and a bearing puller. Safety precautions are provided throughout.
Caterpillar Cat 336D2 L Excavator (Prefix TLY) Service Repair Manual (TLY0000...cnp692569
The document provides instructions for disassembling and assembling a piston pump. It includes 30 steps for assembly, beginning with cleaning parts and ending by filling the hydraulic system with oil. The 3 steps for disassembly are: 1) removing bolts and the head, 2) removing internal components like pistons and bearings, and 3) using tools to remove the rotating group and bearing cone. Protective equipment is recommended as parts are under spring pressure.
Caterpillar Cat 336D L Excavator (Prefix ZML) Service Repair Manual (ZML00001...zatao0179249295
1. The document provides instructions for disassembling and assembling a piston pump used in a 336D L excavator.
2. The disassembly process involves using various tools to remove over 30 individual parts from the pump in sequential order.
3. Reassembly requires carefully installing each part in reverse order, ensuring proper placement of seals, bearings, springs and other components. Special tools and procedures are specified to prevent injury.
Caterpillar Cat 336D L Excavator (Prefix ZML) Service Repair Manual (ZML00001...kesi7153062
1. The document provides instructions for disassembling and assembling a piston pump used in a hydraulic excavator fan.
2. The disassembly process involves using various tools to remove over 30 individual parts from the pump in sequential order.
3. Reassembly requires carefully installing each part in reverse order, ensuring proper placement of seals, bearings, springs and other components.
4. Cleanliness is emphasized throughout to prevent contamination during assembly.
Caterpillar Cat 336D L Excavator (Prefix ZML) Service Repair Manual (ZML00001...cnp692569
1. The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of an excavator.
2. The disassembly process involves removing 30 individual parts in 9 steps, taking care with spring-loaded components.
3. Reassembly requires properly cleaning, inspecting, and installing the 30 components in the reverse order of disassembly over 29 steps. Proper tooling and safety precautions are noted throughout.
Caterpillar Cat 336D L Excavator (Prefix MDS) Service Repair Manual (MDS00001...zatao0179249295
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) on a 336D L excavator. The disassembly process involves removing 30 parts in 9 steps, taking care with springs that can cause injury. The assembly follows the reverse of disassembly and references other sections for installing the pump and filling the hydraulic system.
Caterpillar Cat 336D L Excavator (Prefix MDS) Service Repair Manual (MDS00001...kesi7153062
1. The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of a 336D L excavator.
2. The disassembly process includes removing 30 individual parts in 9 steps, taking care with spring-loaded components.
3. Reassembly requires installing the parts in reverse order, with 30 steps to install all components and ensure proper operation.
Caterpillar Cat 336D L Excavator (Prefix MDS) Service Repair Manual (MDS00001...cnp692569
The document provides instructions for disassembling and assembling a piston pump used in a hydraulic excavator fan. It details 30 steps for removing parts like bearings, seals, pistons, springs, and housings. Proper cleaning of parts is emphasized. Tools needed are also listed. The overall process dismantles the pump into its individual components and then reassembles it for installation.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fhjsjkdmemm
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other internal components. Safety warnings are provided to prevent injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fjjskmdmem
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reassembles the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring loaded parts.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reassembles the pump with 30 parts in 29 steps, requiring cleaning of parts, application of specific temperatures, and use of tools including retaining ring pliers and a dial indicator. Safety precautions are provided throughout regarding spring-loaded parts.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reinstalls the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring-loaded parts.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fjjskekdmmem
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and outlines 30 steps to fully disassemble the pump. These include removing bolts, seals, springs, bearings, pistons, and other internal components. Cleanliness is emphasized throughout the process.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...pfiskdmjekm
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and steps to remove the piston motor, including bending locking tabs and removing bolts and the hub. A lifting device is used to position the fan motor assembly and remove the piston motor. The disassembly procedure includes using tools like a bearing puller to remove components from the piston motor.
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and outlines 30 steps to fully disassemble and reassemble the pump. These include removing housing components, seals, bearings, pistons, springs and other internal parts. Cleanliness is emphasized throughout the process.
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and steps to remove the piston motor, including bending locking tabs and removing bolts and the hub. A lifting device is used to position the fan motor assembly and remove the piston motor. The disassembly procedure includes using tools like a bearing puller to remove components from the piston motor.
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 349F L Excavator (Prefix TEW) Service Repair Manual (TEW00001...zatao0179249295
The document provides instructions to disassemble and assemble the travel motor of 349F and 349F L excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It then describes assembling the motor in reverse order, noting specifications like part numbers, torque values, and lubrication points to reinstall components in their original positions.
Caterpillar Cat 349F L Excavator (Prefix KEA) Service Repair Manual (KEA00001...zatao0179249295
The document provides instructions for disassembling and assembling the travel motor of a 349F L excavator. It lists 30 steps to disassemble the motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It also provides specifications for assembling the motor, such as torque specifications for plugs and bolts, and notes on lubricating sliding surfaces before assembly. The goal is to take the motor apart in a specific sequence and then rebuild it correctly using the provided specifications.
More Related Content
Similar to Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF00001 and up).pdf
Caterpillar Cat 336D2 L Excavator (Prefix TLY) Service Repair Manual (TLY0000...luanxianshi27
The document provides instructions for disassembling and assembling a piston pump. It includes 30 steps for assembly, beginning with cleaning parts and ending with filling the hydraulic system with oil. The 3 steps for disassembly are: 1) removing bolts and the head, 2) removing internal seals and plates, and 3) removing pistons, bearings and other internal components. Tools include retaining ring pliers, a dial indicator, and a bearing puller. Safety precautions are provided for spring loaded parts.
1. The document provides instructions for disassembling and assembling the piston pump of a 336D2 excavator.
2. It details 30 steps for assembly, including installing various parts like bearings, seals, springs, and fasteners.
3. Instructions are accompanied by illustrations and warnings about safety and cleanliness.
The document provides instructions for disassembling and assembling a piston pump. It includes 30 steps for assembly, beginning with cleaning parts and ending by filling the hydraulic system with oil. Disassembly involves 8 steps, starting with removing the head and ending by removing pins from the barrel. Required tools include retaining ring pliers, a dial indicator, and a bearing puller. Safety precautions are provided throughout.
Caterpillar Cat 336D2 L Excavator (Prefix TLY) Service Repair Manual (TLY0000...cnp692569
The document provides instructions for disassembling and assembling a piston pump. It includes 30 steps for assembly, beginning with cleaning parts and ending by filling the hydraulic system with oil. The 3 steps for disassembly are: 1) removing bolts and the head, 2) removing internal components like pistons and bearings, and 3) using tools to remove the rotating group and bearing cone. Protective equipment is recommended as parts are under spring pressure.
Caterpillar Cat 336D L Excavator (Prefix ZML) Service Repair Manual (ZML00001...zatao0179249295
1. The document provides instructions for disassembling and assembling a piston pump used in a 336D L excavator.
2. The disassembly process involves using various tools to remove over 30 individual parts from the pump in sequential order.
3. Reassembly requires carefully installing each part in reverse order, ensuring proper placement of seals, bearings, springs and other components. Special tools and procedures are specified to prevent injury.
Caterpillar Cat 336D L Excavator (Prefix ZML) Service Repair Manual (ZML00001...kesi7153062
1. The document provides instructions for disassembling and assembling a piston pump used in a hydraulic excavator fan.
2. The disassembly process involves using various tools to remove over 30 individual parts from the pump in sequential order.
3. Reassembly requires carefully installing each part in reverse order, ensuring proper placement of seals, bearings, springs and other components.
4. Cleanliness is emphasized throughout to prevent contamination during assembly.
Caterpillar Cat 336D L Excavator (Prefix ZML) Service Repair Manual (ZML00001...cnp692569
1. The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of an excavator.
2. The disassembly process involves removing 30 individual parts in 9 steps, taking care with spring-loaded components.
3. Reassembly requires properly cleaning, inspecting, and installing the 30 components in the reverse order of disassembly over 29 steps. Proper tooling and safety precautions are noted throughout.
Caterpillar Cat 336D L Excavator (Prefix MDS) Service Repair Manual (MDS00001...zatao0179249295
The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) on a 336D L excavator. The disassembly process involves removing 30 parts in 9 steps, taking care with springs that can cause injury. The assembly follows the reverse of disassembly and references other sections for installing the pump and filling the hydraulic system.
Caterpillar Cat 336D L Excavator (Prefix MDS) Service Repair Manual (MDS00001...kesi7153062
1. The document provides instructions for disassembling and assembling the piston pump (hydraulic fan) of a 336D L excavator.
2. The disassembly process includes removing 30 individual parts in 9 steps, taking care with spring-loaded components.
3. Reassembly requires installing the parts in reverse order, with 30 steps to install all components and ensure proper operation.
Caterpillar Cat 336D L Excavator (Prefix MDS) Service Repair Manual (MDS00001...cnp692569
The document provides instructions for disassembling and assembling a piston pump used in a hydraulic excavator fan. It details 30 steps for removing parts like bearings, seals, pistons, springs, and housings. Proper cleaning of parts is emphasized. Tools needed are also listed. The overall process dismantles the pump into its individual components and then reassembles it for installation.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fhjsjkdmemm
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other internal components. Safety warnings are provided to prevent injury from spring forces.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fjjskmdmem
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reassembles the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring loaded parts.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reassembles the pump with 30 parts in 29 steps, requiring cleaning of parts, application of specific temperatures, and use of tools including retaining ring pliers and a dial indicator. Safety precautions are provided throughout regarding spring-loaded parts.
The document provides instructions for disassembling and assembling a piston pump used in excavator models 336D2 and 336D2 L. The disassembly process involves removing 30 parts in 7 steps, using various tools. The assembly process reinstalls the parts in 30 steps, ensuring proper cleaning, heating and cooling of parts, and using tools to set clearances and install retaining rings. Safety precautions are provided to prevent injury from spring-loaded parts.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...fjjskekdmmem
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and outlines 30 steps to fully disassemble the pump. These include removing bolts, seals, springs, bearings, pistons, and other internal components. Cleanliness is emphasized throughout the process.
Caterpillar cat 336 d2 l excavator (prefix ycf) service repair manual (ycf000...pfiskdmjekm
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and steps to remove the piston motor, including bending locking tabs and removing bolts and the hub. A lifting device is used to position the fan motor assembly and remove the piston motor. The disassembly procedure includes using tools like a bearing puller to remove components from the piston motor.
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and outlines 30 steps to fully disassemble and reassemble the pump. These include removing housing components, seals, bearings, pistons, springs and other internal parts. Cleanliness is emphasized throughout the process.
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and steps to remove the piston motor, including bending locking tabs and removing bolts and the hub. A lifting device is used to position the fan motor assembly and remove the piston motor. The disassembly procedure includes using tools like a bearing puller to remove components from the piston motor.
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Similar to Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF00001 and up).pdf (20)
Caterpillar Cat 349F L Excavator (Prefix TEW) Service Repair Manual (TEW00001...zatao0179249295
The document provides instructions to disassemble and assemble the travel motor of 349F and 349F L excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It then describes assembling the motor in reverse order, noting specifications like part numbers, torque values, and lubrication points to reinstall components in their original positions.
Caterpillar Cat 349F L Excavator (Prefix KEA) Service Repair Manual (KEA00001...zatao0179249295
The document provides instructions for disassembling and assembling the travel motor of a 349F L excavator. It lists 30 steps to disassemble the motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It also provides specifications for assembling the motor, such as torque specifications for plugs and bolts, and notes on lubricating sliding surfaces before assembly. The goal is to take the motor apart in a specific sequence and then rebuild it correctly using the provided specifications.
Caterpillar Cat 349F L Excavator (Prefix HPD) Service Repair Manual (HPD00001...zatao0179249295
This document provides instructions for disassembling the travel motor on 349F and 349F L Excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations are provided for each step along with safety notices and required tools. The goal is to break down the travel motor into its core components for repair or replacement.
Caterpillar Cat 349F L Excavator (Prefix HLB) Service Repair Manual (HLB00001...zatao0179249295
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L Excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It also provides specifications for components like plug torque values and spring dimensions to follow when reassembling the travel motor in reverse order.
Caterpillar Cat 349F L Excavator (Prefix BZ2) Service Repair Manual (BZ200001...zatao0179249295
This document provides instructions for disassembling the travel motor on 349F and 349F L Excavator models. It describes 27 steps to fully disassemble the travel motor, including draining fluids, removing housing components, plates, seals, bearings, and other internal parts. Various tools are required, and safety precautions are provided to remove parts under spring tension. The goal is to break down the travel motor into its core components to facilitate repair or replacement of parts.
The document provides instructions to disassemble and assemble the travel motor of 349F and 349F L excavators. It describes 31 steps to disassemble the travel motor by removing components like plugs, seals, springs, pistons, plates, and bearings. It then describes assembling the motor in reverse order, noting specifications like torque values and lubrication points for components like plugs, bolts, seals and bearings.
This document provides instructions to disassemble a travel motor on a 349F and 349F L Excavator. It outlines 27 steps to fully disassemble the travel motor, including draining fluids, removing housing components, plates, pistons, bearings, seals and other internal parts. Various tools are required, including bolts, nuts, pullers, eyebolts and other lifting devices to safely remove parts. Safety precautions are provided to wear protective equipment when removing parts with spring forces.
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L Excavators. It begins by listing the required tools and safety precautions. The 31 step disassembly process removes components like plugs, springs, pistons, plates and seals. The assembly section lists specifications for components and their installation, such as torque values and lubricants to use.
This document provides instructions for disassembling the travel motor on 349F and 349F L Excavator models. It describes 27 steps to fully disassemble the travel motor, including draining fluids, removing housing components, plates, bearings, seals, springs, and pistons. Special care must be taken when removing components under spring pressure. Various tools are required including lifting devices, pullers, bolts and eyebolts to securely support parts being removed.
Caterpillar Cat 349E L Excavator (Prefix TFG) Service Repair Manual (TFG00001...zatao0179249295
1. The document provides step-by-step instructions for disassembling and assembling a hydraulic fan drive for a 349E L excavator.
2. The disassembly process involves removing 22 components and parts from the fan drive assembly including sensors, retainers, seals, plates, discs, and housings.
3. The assembly process lists 8 steps including pressing components back together and installing new seals, sleeves and retaining rings. Precise instructions are provided along with required tools.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...zatao0179249295
The document provides instructions for disassembling and assembling a hydraulic fan drive on an excavator. The disassembly process involves removing 22 components from the fan drive including bolts, seals, retainers, discs, and bearings. The assembly process reverses the disassembly steps and provides illustrations of each step. Precautions are listed regarding cleanliness, handling components, and properly assembling spring-loaded parts.
The document provides instructions for disassembling and assembling a hydraulic fan drive for a 349E excavator. The disassembly process involves removing 22 components from the fan drive including bolts, retainers, seals, discs, plates, and bearings. The assembly process is the reverse and includes applying sealant and installing the components in the proper order and orientation using various tools. Special care must be taken when handling springs and seals. Cleanliness is important to prevent contamination.
Caterpillar Cat 349D2 L Excavator (Prefix XAC) Service Repair Manual (XAC0000...zatao0179249295
This document provides step-by-step instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pistons, and housing. Proper tooling is required and parts must be cleaned, marked and replaced in their original locations and orientations. Safety notices warn of spring forces, contained fluids, and preventing contamination.
Caterpillar Cat 349D2 L Excavator (Prefix WEC) Service Repair Manual (WEC0000...zatao0179249295
This document provides instructions for removing and installing various engine components on a 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing gears, seals, bolts and bearings.
2. Removing the flywheel by detaching lifting brackets, installing guide studs, and removing bolts and the flywheel.
3. Installing the flywheel by heating the ring gear, attaching lifting brackets, applying threadlocker to bolts, and tightening bolts to specification.
4. Removing the crankshaft rear seal by removing bolts and the seal, and inspecting the crankshaft surface.
5. Installing
The document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1) Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2) Removing the flywheel by attaching lifting tools and removing bolts.
3) Removing the crankshaft rear seal by removing bolts.
Installation procedures are also provided with details on cleaning, heating, cooling, and applying threadlocker to parts before tightening to specified torques. Tools required are listed for each procedure.
Caterpillar Cat 349D L Excavator (Prefix FLA) Service Repair Manual (FLA00001...zatao0179249295
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing and installing the rear gear group components like gears, covers, seals, and bearings. Precise measurements and tooling are required for proper installation.
- Procedures for removing and installing the flywheel, which requires lifting equipment due to its weight. The ring gear must be heated for removal and cooled for installation.
- Removing and installing the crankshaft rear seal using specific bolts and torque specifications. Inspection of the crankshaft surface is also noted.
Precise measurements and use of the correct tools are emphasized for correct re
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...zatao0179249295
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
1. The rear gear group is removed by taking off bolts, seals, gears, and covers. Proper bearing installation is emphasized.
2. Flywheel removal requires lifting equipment due to its weight. Installation involves heating the ring gear, applying loctite, and torqueing bolts.
3. Removing the crankshaft rear seal involves taking off bolts. Inspection of the seal surface and crankshaft specifications is noted.
4. Installing the rear seal requires cleaning, applying primer and retaining compound, and following a tightening sequence.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...zatao0179249295
The document provides instructions for disassembling and assembling a swing drive. It lists the required tools and parts. The disassembly process involves removing components like the carrier assembly, ring gear, sun gear and planetary gears. The assembly process instructs to clean parts and apply lubricants before reinstalling components like bearings, seals and gears in the reverse order of disassembly. Proper alignment and pressing of components into place is emphasized.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...zatao0179249295
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine. The removal procedure includes removing the electric starting motor, flywheel, rear crankshaft seal, various gears and covers. The installation procedure describes installing these components in reverse order and provides details on properly positioning bearings and applying threadlocker to bolts. Tools required are also listed.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...zatao0179249295
This document provides instructions for removing and installing the rear gear group on a 345D L excavator with a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 11 steps in the reverse order and provides notes on properly installing bearings, seals, and gears. Tools required are also listed.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR YCF
Configuration: 336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02732015
Piston Pump (Hydraulic Fan) - Assemble
SMCS - 1387-016-QP; 5070-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1857 Retaining Ring Pliers 1
D 8T-5096 Dial Indicator Gp 1
Illustration 1 g01212915
1. Lower the temperature of bearing cup (49). Install bearing cup (49).
1/11
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 2 g01212913
2. Install lip seal (48).
3. Use Tooling (B) in order to install retaining ring (47).
Illustration 3 g01213404
4. Raise the temperature of bearing cone (46).
5. Install bearing cone (46) onto shaft (45).
Illustration 4 g01213405
6. Install bearing cone (46), shaft (45), and bearing cone (31).
2/11
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 5 g01213407
7. Lower the temperature of bearing cone (26). Install bearing cone (26).
Illustration 6 g01212900
8. Position head (23) onto the housing.
9. Install bolts (22).
Illustration 7 g01213409
10. Use Tooling (D) in order to determine the end play of shaft (45).
3/11
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 8 g01212900
11. Remove bolts (22) and head (23).
Illustration 9 g01213405
12. Remove bearing cone (31).
Illustration 10 g01213433
13. Install bearings (44).
4/11
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 11 g01212910
14. Install swashplate (43).
Illustration 12 g01373818
15. Install shim (40), spring (41), and shim (42) to barrel (38).
Illustration 13 g01212908
5/11
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
16. Use Tooling (A), Tooling (B), and a suitable press in order to install retaining ring (39) into
barrel (38).
Illustration 14 g01212907
17. Install pins (37) into barrel (38).
Illustration 15 g01212906
18. Install bearing (36), retainer (35), and pistons (34).
6/11
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 16 g01212905
19. Install rotating group (32) and shim (33).
Note: Shim thickness was determined on Step 9.
Illustration 17 g01212904
20. Install bearing cone (31).
Illustration 18 g01212903
21. Install piston (30).
7/11
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 19 g01212902
22. Install spring (27), piston (29), and O-ring seal (28).
Illustration 20 g01213436
23. Install O-ring seals (24) and port plate (25).
Illustration 21 g01212900
8/11
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
24. Install head (23) and bolts (22).
Illustration 22 g01212898
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
25. Install spool (15), poppet (16), spring (17), spring (18), shim (19), O-ring seal (20), and
housing (21) into housing (2).
26. Install retainer (7), spring (8), retainer (9), spool (10), O-ring seal (12), backup ring (11), O-
ring seal (13), and cartridge (14).
27. Install screw (6) into housing (2).
9/11
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 23 g01212897
28. Install coil (4) and nut (5).
Illustration 24 g01212896
29. Install O-ring seals (3).
Illustration 25 g01212895
30. Install controller (2) and bolts (1).
End By:
10/11
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 En...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. a. Install the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Hydraulic Fan)
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 5 11:14:11 UTC+0800 2020
11/11
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 En...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR YCF
Configuration: 336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02424411
Piston Pump (Hydraulic Fan) - Install
SMCS - 1387-012-QP; 5070-012-HFN
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01211400
1. Position piston pump (7) and install bolts (6).
2. Connect harness assembly (5).
3. Connect hose assemblies (3) and (4).
1/2
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Illustration 2 g01211399
4. Connect hose assembly (2).
Illustration 3 g01206719
5. Close door (1).
6. Fill the hydraulic system with oil. Refer to Operation and Maintenance Manual, "Refill
Capacities".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 5 11:15:07 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR YCF
Configuration: 336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415451
Piston Motor (Hydraulic Fan) - Remove
SMCS - 1386-011-QP; 5058-011-FM
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g01207415
1. Bend locking tabs (1) backward.
2. Remove bolts (2) and hub (3).
1/2
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 2 g01207416
3. Use a suitable lifting device to position fan motor assembly (4) onto suitable cribbing. The
weight of fan motor assembly (4) is approximately 68 kg (150 lb).
Illustration 3 g01207418
4. Attach a suitable lifting device to piston motor (5). The weight of piston motor (5) is
approximately 23 kg (50 lb).
5. Remove bolts (6) and fan motor (5).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 5 11:16:03 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR YCF
Configuration: 336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415272
Piston Motor (Hydraulic Fan) - Disassemble
SMCS - 1386-015-QP; 5058-015-FM; 5058-015-HFN
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9152 Bearing Puller Gp 1
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Start By:
a. Remove the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Remove".
1/7
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 1 g01207275
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove bolts (1) and head (2).
Illustration 2 g01207276
2. Remove O-ring seal (3), port plate (4), and bearing cup (5).
Illustration 3 g01207278
2/7
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove plug (6), sleeve (7), poppet (8), spring (9), poppet (10), and O-ring seal (11).
Illustration 4 g01207279
4. Remove bearing cone (12).
Illustration 5 g01207280
5. Remove shim (13) and rotating group (14).
3/7
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 9 g01207284
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Use Tooling (C) and Tooling (B) in order to remove retaining ring (19).
10. Remove shim (23), spring (22), and shim (21).
Illustration 10 g01207285
11. Remove swashplate (24) and shaft (25).
5/7
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 11 g01207287
12. Use Tooling (A) in order to remove bearing cone (26) from shaft (25).
Illustration 12 g01207286
13. Use Tooling (C) in order to remove retaining ring (27).
14. Remove lip seal (28).
Illustration 13 g01207288
15. Remove bearing cup (29).
6/7
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 L EXCAVATOR YCF
Configuration: 336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415273
Piston Motor (Hydraulic Fan) - Assemble
SMCS - 1386-016-QP; 5058-016-FM; 5058-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Illustration 1 g01207288
1. Install bearing cup (29).
1/7
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 2 g01207286
2. Install lip seal (28).
3. Use Tooling (C) in order to install retaining ring (27).
Illustration 3 g01207624
4. Raise the temperature of bearing cone (26).
5. Install bearing cone (26) onto shaft (25).
Illustration 4 g01207285
6. Install shaft (25) and swashplate (24).
2/7
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Illustration 5 g01207283
Illustration 6 g01207284
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
7. Install shim (21), spring (22), and shim (23).
8. Use Tooling (C) and Tooling (B) in order to install retaining ring (19).
3/7
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Illustration 7 g01207282
9. Install pins (18).
Illustration 8 g01207281
10. Install bearing (17).
11. Install pistons (15) and retainer (16).
Illustration 9 g01207280
12. Install rotating group (14) and shim (13).
4/7
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Illustration 10 g01207279
13. Install bearing cone (12).
Illustration 11 g01207278
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install O-ring seal (11), poppet (10), spring (9), poppet (8), sleeve (7), and plug (6).
5/7
336D2 & 336D2 L Excavators YCF00001-UP (MACHINE) POWERED BY C9 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...