1) The document provides instructions for removing and installing various engine components, including the engine oil filter base, engine oil cooler, hydraulic oil cooler, and air cleaner.
2) The procedures note that cleanliness is important and tools may be required for some removal and installation steps.
3) Technicians are advised to follow the steps carefully to correctly disassemble and reassemble the components.
Caterpillar cat 336 d l excavator (prefix kkt) service repair manual (kkt0000...fjskemdme
1. The document provides instructions for removing and installing the engine oil filter base, engine oil cooler, and hydraulic oil cooler on Caterpillar 336D and 336D L excavators.
2. The procedures emphasize cleanliness and inspecting parts for wear or damage before assembly.
3. Individual components are removed and installed using the proper tools and following illustrated steps and tightening sequences.
Caterpillar cat 336 d l excavator (prefix kkt) service repair manual (kkt0000...fjskkkdmem
1. The document provides instructions for removing and installing the engine oil filter base, engine oil cooler, and hydraulic oil cooler on Caterpillar 336D and 336D L excavators.
2. The procedures emphasize cleanliness and inspecting parts for wear or damage before assembly.
3. Individual components are removed and installed using the proper tools and following illustrated steps and tightening sequences.
Caterpillar cat 336 d excavator (prefix kkt) service repair manual (kkt00001 ...fjskemdme
1. The document provides instructions for removing and installing the engine oil filter base, engine oil cooler, and hydraulic oil cooler on Caterpillar 336D and 336D L excavators.
2. The procedures emphasize cleanliness and inspecting parts for wear or damage before assembly.
3. Individual components are removed and installed according to illustrated steps, with required tools listed at the start of each section.
Caterpillar cat 336 d excavator (prefix kkt) service repair manual (kkt00001 ...fjskkkdmem
1. The document provides instructions for removing and installing various engine components on 336D and 336D L excavators, including the engine oil filter base, engine oil cooler, hydraulic oil cooler, and air cleaner.
2. The procedures describe cleaning parts, removing and installing components using the proper tools and fasteners, and ensuring correct assembly.
3. Cleanliness is emphasized as important to prevent dirt from entering components.
Caterpillar cat 336 d l excavator (prefix kkt) service repair manual (kkt0000...fjjsekwsxkdmmem
1. The document provides instructions for removing and installing various engine components on a 336D excavator, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. The procedures describe cleaning parts, using specific tools, removing bolts and hoses, and ensuring proper installation of gaskets and components.
3. Technicians are advised to follow the steps carefully to correctly disassemble and reassemble parts in the specified order.
Caterpillar cat 336 d excavator (prefix kkt) service repair manual (kkt00001 ...fjjsekwsxkdmmem
1. The document provides instructions for removing and installing various engine components on a 336D excavator, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. The procedures describe cleaning parts, using specific tools, removing bolts and hoses, and ensuring proper installation of gaskets and components.
3. Technicians are advised to follow the steps carefully to correctly disassemble and reassemble parts in the specified order.
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...fujkskemdmdm4r
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar cat 336 d l excavator (prefix kkt) service repair manual (kkt0000...fjskemdme
1. The document provides instructions for removing and installing the engine oil filter base, engine oil cooler, and hydraulic oil cooler on Caterpillar 336D and 336D L excavators.
2. The procedures emphasize cleanliness and inspecting parts for wear or damage before assembly.
3. Individual components are removed and installed using the proper tools and following illustrated steps and tightening sequences.
Caterpillar cat 336 d l excavator (prefix kkt) service repair manual (kkt0000...fjskkkdmem
1. The document provides instructions for removing and installing the engine oil filter base, engine oil cooler, and hydraulic oil cooler on Caterpillar 336D and 336D L excavators.
2. The procedures emphasize cleanliness and inspecting parts for wear or damage before assembly.
3. Individual components are removed and installed using the proper tools and following illustrated steps and tightening sequences.
Caterpillar cat 336 d excavator (prefix kkt) service repair manual (kkt00001 ...fjskemdme
1. The document provides instructions for removing and installing the engine oil filter base, engine oil cooler, and hydraulic oil cooler on Caterpillar 336D and 336D L excavators.
2. The procedures emphasize cleanliness and inspecting parts for wear or damage before assembly.
3. Individual components are removed and installed according to illustrated steps, with required tools listed at the start of each section.
Caterpillar cat 336 d excavator (prefix kkt) service repair manual (kkt00001 ...fjskkkdmem
1. The document provides instructions for removing and installing various engine components on 336D and 336D L excavators, including the engine oil filter base, engine oil cooler, hydraulic oil cooler, and air cleaner.
2. The procedures describe cleaning parts, removing and installing components using the proper tools and fasteners, and ensuring correct assembly.
3. Cleanliness is emphasized as important to prevent dirt from entering components.
Caterpillar cat 336 d l excavator (prefix kkt) service repair manual (kkt0000...fjjsekwsxkdmmem
1. The document provides instructions for removing and installing various engine components on a 336D excavator, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. The procedures describe cleaning parts, using specific tools, removing bolts and hoses, and ensuring proper installation of gaskets and components.
3. Technicians are advised to follow the steps carefully to correctly disassemble and reassemble parts in the specified order.
Caterpillar cat 336 d excavator (prefix kkt) service repair manual (kkt00001 ...fjjsekwsxkdmmem
1. The document provides instructions for removing and installing various engine components on a 336D excavator, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. The procedures describe cleaning parts, using specific tools, removing bolts and hoses, and ensuring proper installation of gaskets and components.
3. Technicians are advised to follow the steps carefully to correctly disassemble and reassemble parts in the specified order.
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...fujkskemdmdm4r
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...zan2736ban
1. The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. Removal and installation procedures are outlined in steps with accompanying illustrations. Cleanliness is emphasized and inspecting parts for wear or damage before reassembly.
3. Tools required are listed for some procedures. Proper lifting of heavy components like the hydraulic oil cooler is advised to prevent injury.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...f8uesjdkdmdm
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...f8sejdkdmdijd
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
The document provides instructions for servicing components of 336D and 336D L excavators, including:
1) Procedures for assembling the engine oil filter base, requiring installation of seals, plugs, and covers.
2) Steps for installing the engine oil filter base, including attaching hoses and bolting it into place.
3) Removing and installing the engine oil cooler and hydraulic oil cooler, describing lifting equipment needed and connection of hoses.
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...ze3xiandiao
1. The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. Removal and installation procedures are outlined in steps with accompanying illustrations. Cleanliness is emphasized and inspecting parts for wear or damage before reassembly.
3. Tools required are listed for some procedures. Proper lifting of heavy components like the hydraulic oil cooler is advised to prevent injury.
The document provides instructions for servicing components of 336D and 336D L excavators, including:
1) Procedures for assembling the engine oil filter base, requiring installation of seals, plugs, and covers.
2) Steps for installing the engine oil filter base, including attaching hoses and bolting it into place.
3) Removing and installing the engine oil cooler and hydraulic oil cooler, describing lifting equipment and replacement of gaskets.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...f7usuejkdkddm3
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...ufs89eodkdmdm
1. The document provides instructions for removing and installing various engine components on a 336D excavator, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. The procedures describe cleaning parts, using specific tools, removing bolts and hoses, and ensuring proper installation.
3. Technicians are advised to follow the steps carefully to correctly disassemble and reassemble parts.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...jdkskmmdmd1
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...jdkskmdmdm
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
1. The document provides instructions for removing and installing various engine components on a 336D excavator, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. The procedures describe cleaning parts, using specific tools, removing bolts and hoses, and ensuring proper installation.
3. Technicians are advised to follow the steps carefully to correctly disassemble and reassemble parts.
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...pwg56547003
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
1. The document provides instructions for servicing parts of a 336D excavator, including installing an engine oil filter base, installing an engine oil cooler, and removing and installing a hydraulic oil cooler.
2. Steps are provided to clean parts, install valves, seals, and plugs into the engine oil filter base.
3. Instructions are given to install the engine oil filter base, connect hoses, and fill the engine with coolant.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...zatao0179249295
1. The document provides instructions for installing and removing various engine components on a 336D excavator, including the engine oil filter base, engine oil cooler, hydraulic oil cooler, and air cleaner.
2. The procedures describe cleaning parts, using proper tools, and connecting hoses and brackets in the specified order.
3. Technicians are advised to follow the steps carefully and use new replacement parts if old parts are worn or damaged.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...kesi7153062
1. The document provides instructions for installing and removing various engine components on a 336D excavator, including the engine oil filter base, engine oil cooler, hydraulic oil cooler, and air cleaner.
2. The procedures describe cleaning parts, using required tools, installing and removing gaskets, hoses, brackets, covers, and other components in a specified sequence.
3. Technicians are advised to follow the established procedures carefully and wear protective equipment when working with spring-loaded parts to prevent injury.
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and other attachments, and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and other parts are then removed to separate the outside housing from the rotor.
More Related Content
Similar to Caterpillar Cat 336D LN EXCAVATOR (Prefix L5K) Service Repair Manual (L5K00001 and up).pdf
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...zan2736ban
1. The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. Removal and installation procedures are outlined in steps with accompanying illustrations. Cleanliness is emphasized and inspecting parts for wear or damage before reassembly.
3. Tools required are listed for some procedures. Proper lifting of heavy components like the hydraulic oil cooler is advised to prevent injury.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...f8uesjdkdmdm
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...f8sejdkdmdijd
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
The document provides instructions for servicing components of 336D and 336D L excavators, including:
1) Procedures for assembling the engine oil filter base, requiring installation of seals, plugs, and covers.
2) Steps for installing the engine oil filter base, including attaching hoses and bolting it into place.
3) Removing and installing the engine oil cooler and hydraulic oil cooler, describing lifting equipment needed and connection of hoses.
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...ze3xiandiao
1. The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. Removal and installation procedures are outlined in steps with accompanying illustrations. Cleanliness is emphasized and inspecting parts for wear or damage before reassembly.
3. Tools required are listed for some procedures. Proper lifting of heavy components like the hydraulic oil cooler is advised to prevent injury.
The document provides instructions for servicing components of 336D and 336D L excavators, including:
1) Procedures for assembling the engine oil filter base, requiring installation of seals, plugs, and covers.
2) Steps for installing the engine oil filter base, including attaching hoses and bolting it into place.
3) Removing and installing the engine oil cooler and hydraulic oil cooler, describing lifting equipment and replacement of gaskets.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...f7usuejkdkddm3
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...ufs89eodkdmdm
1. The document provides instructions for removing and installing various engine components on a 336D excavator, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. The procedures describe cleaning parts, using specific tools, removing bolts and hoses, and ensuring proper installation.
3. Technicians are advised to follow the steps carefully to correctly disassemble and reassemble parts.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...jdkskmmdmd1
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D and 336D L Excavator (Prefix KKT) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...jdkskmdmdm
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
1. The document provides instructions for removing and installing various engine components on a 336D excavator, including the engine oil filter base, engine oil cooler, and hydraulic oil cooler.
2. The procedures describe cleaning parts, using specific tools, removing bolts and hoses, and ensuring proper installation.
3. Technicians are advised to follow the steps carefully to correctly disassemble and reassemble parts.
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...pwg56547003
The document provides instructions for removing and installing various engine components on Caterpillar 336D and 336D L excavators, including:
1) Removing and installing the engine oil filter base in 3 steps.
2) Removing and installing the engine oil cooler in 2 steps.
3) Removing and installing the hydraulic oil cooler in 5 steps.
4) Removing and installing the air cleaner in 6 steps.
1. The document provides instructions for servicing parts of a 336D excavator, including installing an engine oil filter base, installing an engine oil cooler, and removing and installing a hydraulic oil cooler.
2. Steps are provided to clean parts, install valves, seals, and plugs into the engine oil filter base.
3. Instructions are given to install the engine oil filter base, connect hoses, and fill the engine with coolant.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...zatao0179249295
1. The document provides instructions for installing and removing various engine components on a 336D excavator, including the engine oil filter base, engine oil cooler, hydraulic oil cooler, and air cleaner.
2. The procedures describe cleaning parts, using proper tools, and connecting hoses and brackets in the specified order.
3. Technicians are advised to follow the steps carefully and use new replacement parts if old parts are worn or damaged.
Caterpillar Cat 336D L Excavator (Prefix KKT) Service Repair Manual (KKT00001...kesi7153062
1. The document provides instructions for installing and removing various engine components on a 336D excavator, including the engine oil filter base, engine oil cooler, hydraulic oil cooler, and air cleaner.
2. The procedures describe cleaning parts, using required tools, installing and removing gaskets, hoses, brackets, covers, and other components in a specified sequence.
3. Technicians are advised to follow the established procedures carefully and wear protective equipment when working with spring-loaded parts to prevent injury.
Similar to Caterpillar Cat 336D LN EXCAVATOR (Prefix L5K) Service Repair Manual (L5K00001 and up).pdf (20)
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and other attachments, and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and other parts are then removed to separate the outside housing from the rotor.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...f8usiedkdmm
This document provides instructions for removing and installing the final drive and travel motor on 330D L and 330D N Hydraulic Excavators. The removal procedure involves separating the track, disconnecting hydraulic lines, and removing mounting bolts to lift the final drive and travel motor assembly out. The installation procedure specifies cleaning and inspecting parts, attaching components in the reverse order of removal, and refilling the hydraulic system. Tools and safety precautions are also listed.
Caterpillar Cat 330-A L EXCAVATOR (Prefix 9ML) Service Repair Manual (9ML0000...f8usiedkdmm
The document provides instructions for installing and removing a turbocharger on a Caterpillar 330 excavator engine:
1) To remove the turbocharger, loosen clamps and bolts holding the oil supply/drain tubes and housing. Remove the turbocharger and check seals.
2) To install the turbocharger, position it on the exhaust manifold with new gaskets. Attach the oil tubes and housing with bolts and clamps.
3) The instructions also cover removing and installing the exhaust manifold, which involves removing nuts and studs, checking gaskets, and attaching the manifold.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...f8usiedkdmm
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 3YR) Service Repair Manual (3YR00001...f8usiedkdmm
The document provides instructions for servicing components of a 330B L excavator, including:
1) Installing a compression brake and connecting wires and bolts.
2) Removing and disassembling a rocker shaft assembly by removing retaining rings, springs, and supports.
3) Assembling a rocker shaft by installing supports, springs, washers and tightening bolts.
Caterpillar Cat 385C L Excavator (Prefix JCM) Service Repair Manual (JCM00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. It cautions to check all O-rings and seals for wear and replace if needed.
This document provides instructions for disassembling and assembling the travel motor of a 329E Mobile Hydraulic Power Unit. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 23 steps for assembly, reinstalling those components in reverse order while noting proper lubrication and alignment of parts. Tools required are also listed.
The document provides instructions for removing and installing valve components on a Caterpillar C-18 engine, including:
1) Removal and installation procedures for the variable valve actuator, requiring removal of the valve mechanism cover and disconnection of electrical harnesses.
2) Removal of the rocker arm assembly by removing mounting bolts and studs and lifting it out as a unit.
3) Disassembly of individual rocker arms by removing adjustment screws, buttons, and O-rings.
4) Reassembly of rocker arms and installation of the rocker arm assembly by positioning it, installing mounting hardware, and adjusting valves and injectors.
The document provides instructions for removing and installing various engine components on a Caterpillar C13 engine, including:
- Removing the valve cover, rocker arm and shaft, cylinder head, and other components. Cleaning and inspecting parts during removal.
- Installing components by reversing the removal procedures, applying anti-seize compound, adjusting clearances, and reconnecting wiring harnesses and fluid lines.
- Detailed steps include using lifting tools to handle heavy parts like the cylinder head, removing and tightening bolts in a specific sequence, and ensuring proper reinstallation of identification marks and plugs on disconnected lines.
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. It begins with removing the final drive and describes dismantling it into individual parts like the ring gear, carrier assemblies, planetary gears and shafts. Alignment marks are noted to aid reassembly. The instructions then describe assembling the final drive components back into the final drive housing.
Caterpillar Cat 345B II MH EXCAVATOR (Prefix APB) Service Repair Manual (APB0...f8usiedkdmm
The document provides instructions for disassembling a swing drive on an excavator. Key steps include:
1. Draining the oil from the swing drive and removing attachments like the dipstick and filler cap.
2. Removing bolts and washers to separate the cover from the swing drive housing.
3. Using tools to disassemble the internal components of the carrier assemblies, including planetary gears.
4. Removing the ring gear, sun gear, and other large internal components from the swing drive housing.
Caterpillar Cat 345C Mobile Hydraulic Excavator (Prefix M3E) Service Repair M...f8usiedkdmm
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, seals and other components. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the reverse order of disassembly. Contamination of hydraulic systems must be avoided during the process.
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and tightening sequences are provided. The installation ends by installing a crankshaft rear seal.
This document provides instructions for removing and installing cylinder heads on 345B and 345B L excavator models. The removal procedure involves removing various components to access the cylinder head such as the valve cover, rocker arms, and pushrods. Specific bolts and sensors must then be removed from the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, and tightening head bolts to the proper torque. Special tools and repair kits are listed for tasks such as removing fuel filters and repairing damaged cylinder block threads.
Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM0000...f8usiedkdmm
The document provides instructions for removing and installing various engine components, including:
1) Removing the cylinder head which involves first removing the fuel injection lines and exhaust manifold.
2) Instructions for disassembling the rocker shaft which includes removing rocker arms, springs, and supports.
3) Procedures for assembling the rocker shaft by installing the rocker arms, supports, springs and securing with a pin and plugs.
Caterpillar Cat 329F L Excavator (Prefix ERL) Service Repair Manual (ERL00001...f8usiedkdmm
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
The document provides instructions for removing and installing various components of a Caterpillar C7.1 engine, including the vibration damper and pulley, crankshaft front seal, and front cover. The removal procedures involve using various tools to remove screws, bolts, seals and other parts. The installation procedures specify cleaning components, installing new seals and gaskets, and tightening bolts to the specified torques.
The document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that include removing the motor head, brake components, rotating assembly, seals and other parts. It then lists 12 steps for assembly that include installing seals, piston assemblies, cam plate and other components in the reverse order of disassembly. Precautions are provided regarding spring loaded parts and proper positioning of marked components. Required tools are listed.
Caterpillar Cat 385C L MH EXCAVATOR (Prefix WAW) Service Repair Manual (WAW00...f8usiedkdmm
This document provides instructions for removing and installing fuel system components on a Caterpillar 385C L MH EXCAVATOR. The components include the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors. The procedures describe disconnecting hoses, removing mounting bolts, and using various tools to properly remove and install each component while keeping parts clean and free of contaminants.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR L5K
Configuration: 336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit C9 Engine Supplement
Media Number -RENR8647-16 Publication Date -01/10/2015 Date Updated -26/10/2015
i02417234
Engine Oil Filter Base - Disassemble
SMCS - 1306-015; 1306
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
1/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01208235
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 1. Remove connector (20) and O-ring seal (19).
2. Remove cover (18) and O-ring seal (16).
3. Remove stud (17).
4. Remove connector (14) and O-ring seal (15).
5. Remove adapter (12) and O-ring seal (10).
6. Remove plug (2) and O-ring seal (3).
7. Remove plug (13), O-ring seal (11), spring (9), and valve (8) from engine oil filter base (1).
8. Remove plug (4), O-ring seal (5), spring (6), and valve (7) from engine oil filter base (1).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 07:27:43 UTC+0800 2020
3/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR L5K
Configuration: 336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit C9 Engine Supplement
Media Number -RENR8647-16 Publication Date -01/10/2015 Date Updated -26/10/2015
i02417236
Engine Oil Filter Base - Assemble
SMCS - 1306-016; 1306
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
1/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g01208235
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 1. Install valve (7), spring (6), O-ring seal (5), and plug (4) into engine oil filter base (1).
2. Install valve (8), spring (9), O-ring seal (11), and plug (13) into engine oil filter base (1).
3. Install O-ring seal (3) and plug (2).
4. Install O-ring seal (10) and adapter (12).
5. Install O-ring seal (15) and connector (14).
6. Install stud (17).
7. Install O-ring seal (16) and cover (18).
8. Install O-ring seal (19) and connector (20).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 07:28:38 UTC+0800 2020
3/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR L5K
Configuration: 336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit C9 Engine Supplement
Media Number -RENR8647-16 Publication Date -01/10/2015 Date Updated -26/10/2015
i02417231
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M8 - 1.25 by 65 mm
2
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01208181
1/4
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 1. Install the gasket and engine oil filter base (10) over Tooling (A).
2. Install bolts (9).
Illustration 2 g01208179
Illustration 3 g01208224
3. Remove Tooling (A) and install bolts (8). Refer to Illustration 3 for the correct tightening
sequence.
2/4
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 4 g01208178
4. Connect hose assemblies (6) and (7).
Illustration 5 g01208176
5. Install hose (5).
Illustration 6 g01208119
6. Close engine hood (4).
3/4
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 7 g01208173
7. Connect hose assembly (3).
Illustration 8 g01208170
8. Raise guard (2) and install bolts (1).
9. fill the engine with coolant. Refer to Operation and Maintenance Manual, "Refill
Capacities".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 07:29:34 UTC+0800 2020
4/4
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR L5K
Configuration: 336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit C9 Engine Supplement
Media Number -RENR8647-16 Publication Date -01/10/2015 Date Updated -26/10/2015
i02417228
Engine Oil Cooler - Remove and Install
SMCS - 1378-010
Removal Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g01208148
1. Remove gasket (1) and engine oil cooler (2).
Installation Procedure
1/2
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 2 g01208148
1. Install engine oil cooler (2) and gasket (1).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 07:30:30 UTC+0800 2020
2/2
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR L5K
Configuration: 336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit C9 Engine Supplement
Media Number -RENR8647-16 Publication Date -01/10/2015 Date Updated -26/10/2015
i02415509
Hydraulic Oil Cooler - Remove and Install
SMCS - 1374-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 189-0408 Shackle As 2
Start By:
a. Remove the fan group. Refer to Disassembly and Assembly, "Fan Group (Includes Fan, Fan
Guard, Fan Shroud, and Hydraulic Fan Motor) - Remove".
Illustration 1 g01207524
1. Remove hose (1), bolts (2), and plate (3).
1/5
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g01207525
2. Remove bolts (4) and bracket (5).
Illustration 3 g01207526
3. Attach Tooling (A) and a suitable lifting device to hydraulic oil cooler (6). The weight of
hydraulic oil cooler (6) is approximately 68 kg (150 lb).
4. Remove bolt (7).
Illustration 4 g01207527
5. Remove bolts (8).
2/5
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 5 g01207528
6. Use the suitable lifting device to remove hydraulic oil cooler (6).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 189-0408 Shackle As 2
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 6 g01207528
1. Use Tooling (A) and a suitable lifting device to position hydraulic oil cooler (6). The weight
of hydraulic oil cooler (6) is approximately 68 kg (150 lb).
3/5
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 7 g01207527
2. Install bolts (8).
Illustration 8 g01207526
3. Install bolt (7) and remove Tooling (A) from hydraulic oil cooler (6).
Illustration 9 g01207525
4. Install bracket (5) and bolts (4).
4/5
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 10 g01207524
5. Install plate (3), bolts (2), and hose (1).
End By:
a. Install the fan group. Refer to Disassembly and Assembly, "Fan Group (Includes Fan, Fan
Guard, Fan Shroud, and Hydraulic Fan Motor) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 07:31:26 UTC+0800 2020
5/5
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR L5K
Configuration: 336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit C9 Engine Supplement
Media Number -RENR8647-16 Publication Date -01/10/2015 Date Updated -26/10/2015
i02412726
Air Cleaner - Remove and Install
SMCS - 1051-010; 1054-010
Removal Procedure
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g01205948
1. Open doors (2) and (1).
1/6
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 2 g01206308
2. Remove cover (3).
Illustration 3 g01206309
Illustration 4 g01206310
3. Remove primary filter element (4) and secondary filter element (5).
2/6
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 5 g01206311
4. Disconnect hose (6) from the back of air cleaner assembly (7).
Illustration 6 g01206312
5. Remove bolts (8) and air cleaner assembly (7).
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
3/6
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 7 g01206312
1. Install air cleaner assembly (7) and bolts (8).
Illustration 8 g01206311
2. Connect hose (6) to the back of air cleaner assembly (7).
Illustration 9 g01206310
4/6
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 10 g01206309
3. Install secondary filter element (5) and primary filter element (4).
Illustration 11 g01206308
4. Install cover (3).
Illustration 12 g01205948
5. Close doors (1) and (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Fri Aug 21 07:32:21 UTC+0800 2020
5/6
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D LN EXCAVATOR L5K
Configuration: 336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit C9 Engine Supplement
Media Number -RENR8647-16 Publication Date -01/10/2015 Date Updated -26/10/2015
i02412735
Ether Start Valve - Remove and Install
SMCS - 1456-010-VL
Removal Procedure
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
Illustration 1 g01205948
1. Open doors (2) and (1).
1/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 2 g01205972
2. Disconnect harness assembly (3) and tube assembly (6).
3. Remove bolts (4) and ether start valve (5).
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 3 g01205972
1. Position ether start valve (5) and install bolts (4).
2. Connect harness assembly (3) and tube assembly (6).
2/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 4 g01205948
3. Close doors (1) and (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 07:33:17 UTC+0800 2020
3/3
336D LN Mobile Hydraulic Power Unit L5K00001-UP (MACHINE) POWERED BY ...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...