This document provides instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly that involve removing components like the head, O-rings, springs, plates, and seals. The assembly section lists 28 corresponding steps to reinstall these components in reverse order, noting to clean parts thoroughly, apply lubricant, and ensure proper positioning of marked components. Special tools are listed that may be required for tasks like removing races and installing seals and rings. Safety precautions are provided around spring loading and following procedures.
Caterpillar cat 336 d l excavator (prefix w3k) service repair manual (w3k0000...fjjskekdm
The document provides assembly instructions for a travel motor. Key steps include cleaning and inspecting parts, applying lubricant to components, and installing seals, bearings and other components in the proper order and orientation. Tools are required to install retaining rings, seals and bearing races. Torque specifications and notes on part markings are also provided to ensure correct assembly.
Caterpillar cat 336 d l excavator (prefix w3k) service repair manual (w3k0000...fjekkdmmem
The document provides assembly instructions for a travel motor. Key steps include cleaning and inspecting parts, applying lubricant to components, and installing seals, bearings and other components in the proper order and orientation. Special tools are required to install retaining rings, seals and bearing races correctly. Proper positioning of marked components like pistons must be followed for correct assembly.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...shudun96087
The document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 17 steps for assembly, reinstalling those components in reverse order, noting proper lubrication and torque specifications. Tools required include retaining ring pliers, a bearing puller, threaded rod, and Loctite.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...cnp692569
The document provides instructions to disassemble and assemble the travel motor of a 329E L excavator. Key steps include:
1. Removing the travel motor and cleaning it prior to disassembly.
2. Disassembling components like the head, brake piston, rotating assembly, and seals.
3. Inspecting parts and replacing as needed.
4. Assembling follows the reverse order, with components like seals, piston assemblies, and bearing races installed using press tools and lubricant. Proper alignment of parts is important for correct assembly.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...kesi7153062
The document provides instructions to disassemble and assemble the travel motor of a 329E L excavator. Key steps include:
1. Removing the head, seals, springs, brake components, and rotating assembly from the motor housing.
2. Pressing out bearings and races from the shaft and housing.
3. Reinstalling bearings, seals, brake components, piston assemblies, and rotating assembly back into the housing.
4. Reattaching the head and testing operation of the assembled travel motor.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...f7djidksmd3e
This document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists the required tools and presents 28 steps to fully disassemble the travel motor by removing components like the head, brake piston, plates, seals, bearings and housing covers. The 28 steps of assembly are then described to reinstall these components in reverse order using the appropriate tools, lubricants, and torque specifications.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...paws21610697
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar cat 336 d l excavator (prefix w3k) service repair manual (w3k0000...fjjskekdm
The document provides assembly instructions for a travel motor. Key steps include cleaning and inspecting parts, applying lubricant to components, and installing seals, bearings and other components in the proper order and orientation. Tools are required to install retaining rings, seals and bearing races. Torque specifications and notes on part markings are also provided to ensure correct assembly.
Caterpillar cat 336 d l excavator (prefix w3k) service repair manual (w3k0000...fjekkdmmem
The document provides assembly instructions for a travel motor. Key steps include cleaning and inspecting parts, applying lubricant to components, and installing seals, bearings and other components in the proper order and orientation. Special tools are required to install retaining rings, seals and bearing races correctly. Proper positioning of marked components like pistons must be followed for correct assembly.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...shudun96087
The document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists 28 steps for disassembly, removing components like the head, brake piston, rotating assembly, and seals. It then lists 17 steps for assembly, reinstalling those components in reverse order, noting proper lubrication and torque specifications. Tools required include retaining ring pliers, a bearing puller, threaded rod, and Loctite.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...cnp692569
The document provides instructions to disassemble and assemble the travel motor of a 329E L excavator. Key steps include:
1. Removing the travel motor and cleaning it prior to disassembly.
2. Disassembling components like the head, brake piston, rotating assembly, and seals.
3. Inspecting parts and replacing as needed.
4. Assembling follows the reverse order, with components like seals, piston assemblies, and bearing races installed using press tools and lubricant. Proper alignment of parts is important for correct assembly.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...kesi7153062
The document provides instructions to disassemble and assemble the travel motor of a 329E L excavator. Key steps include:
1. Removing the head, seals, springs, brake components, and rotating assembly from the motor housing.
2. Pressing out bearings and races from the shaft and housing.
3. Reinstalling bearings, seals, brake components, piston assemblies, and rotating assembly back into the housing.
4. Reattaching the head and testing operation of the assembled travel motor.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...f7djidksmd3e
This document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists the required tools and presents 28 steps to fully disassemble the travel motor by removing components like the head, brake piston, plates, seals, bearings and housing covers. The 28 steps of assembly are then described to reinstall these components in reverse order using the appropriate tools, lubricants, and torque specifications.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...f8usiedkdmm
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...paws21610697
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and presents 28 steps to take the travel motor apart and put it back together. The steps include removing components like the head, brake piston, barrel assembly parts, and seals and installing them in reverse order. Cautions are provided about spring force and ensuring proper alignment of parts.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...jdjkskmikdkmd
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...udjdkkmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists the required tools and presents 28 steps to fully disassemble the travel motor by removing components like the head, brake piston, plates, seals, bearings and housing covers. The 28 steps of assembly are then described to reinstall these components in reverse order using the appropriate tools, lubricants, and torque specifications.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists the required tools and presents 28 steps to fully disassemble the travel motor by removing components like the head, brake piston, plates, seals, bearings and housing covers. The 28 steps of assembly are then described to reinstall these components in reverse order using the appropriate tools, lubricants, and torques. Key steps include removing and installing retaining rings, seals, bearings and repositioning marked components in their original locations.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar Cat 329E L Excavator (Prefix RLD) Service Repair Manual (RLD00001...jdjkskmikdkmd
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Caterpillar Cat 325C FM EXCAVATOR (Prefix Y4P) Service Repair Manual (Y4P0000...ufs89eodkdmdm
This document provides instructions for disassembling and assembling the final drive of a 325C FM excavator. It lists the required tools and parts. The disassembly procedure involves removing over 30 components of the final drive including sprockets, gears, seals, plates, and housings. Detailed illustrations are provided to show how to remove each part correctly. The assembly procedure is not included.
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, and piston assemblies. Proper cleaning and identification of parts is emphasized to ensure correct reassembly. Tools required are listed in a table.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...ufs89eodkdmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...ufs89eodkdmdm
The document provides instructions for assembling a travel motor on an excavator. It details 27 steps including installing seals, springs, pistons and other components into the motor housing. The motor is then installed onto the final drive assembly and excavator frame using bolts. Proper lubrication and torque specifications are emphasized to correctly assemble the travel motor.
1. The document provides installation instructions for an implement pump on a D8T track-type tractor. It describes 34 steps for installing various parts like valves, springs, seals and bearings into the pump housing.
2. Precautions are provided to ensure fluids are contained and parts are cleaned before assembly. Tools required are listed. Lubrication and heating of some parts is specified before installation.
3. Once assembled, the pump is attached to the tractor using bolts and hoses are connected to the manifold and slip joints.
This document provides instructions for removing and installing the front housing of a C27 Industrial Engine. The removal procedure involves detaching various components from the front of the engine like the water pump, oil filter housing, and brackets. Tools are required to remove some parts. The installation procedure specifies applying sealant, positioning the front housing and gasket, and installing bolts and other parts in the reverse order of removal. Tightening torques are provided for the bolts.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C9 Industrial Engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing a unit injector from the cylinder head
The procedures describe draining fluids, removing bolts and hoses, cleaning parts, replacing seals, and torquing fasteners to the specified values. Special tools are listed for many of the removal and installation steps.
This document provides instructions for removing and installing inlet and exhaust valves on a C27 Industrial Engine. It describes:
- Using a valve spring compressor tool to remove the valve springs and valve spring retainers.
- Inspecting the valves and checking the spring force.
- Lubricating the valve stems before installation and compressing the springs with a tool to install the retainers.
- Cautions for wearing protective equipment when working with springs to avoid injury from parts propelled by the springs.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
This document provides instructions for removing and installing the engine oil filter base and oil cooler on a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Reversing the removal procedures for installation, including applying oil to seals and tightening bolts in a specific sequence
1) The document provides instructions for removing and installing various components of a Caterpillar C9.3 industrial engine, including disconnecting snap-to-connect fittings, removing and installing a muffler, and removing and installing a fuel priming pump and fuel filter base.
2) The procedures include illustrations showing the components and numbered steps for disassembly and reassembly. Safety warnings are provided at the beginning regarding relieving pressures before disconnection.
3) Torque specifications and required tools are listed for relevant installation steps.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing the engine oil filter base and oil cooler on a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Reversing the removal procedures for installation, including applying oil to seals and tightening bolts in a specific sequence
More Related Content
Similar to Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual (W3K00001 and up).pdf
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and presents 28 steps to take the travel motor apart and put it back together. The steps include removing components like the head, brake piston, barrel assembly parts, and seals and installing them in reverse order. Cautions are provided about spring force and ensuring proper alignment of parts.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual (ZCD00001...jdjkskmikdkmd
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...udjdkkmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists the required tools and presents 28 steps to fully disassemble the travel motor by removing components like the head, brake piston, plates, seals, bearings and housing covers. The 28 steps of assembly are then described to reinstall these components in reverse order using the appropriate tools, lubricants, and torque specifications.
Caterpillar Cat 329E L Excavator (Prefix ZCD) Service Repair Manual Instant D...yan77xunhao
This document provides instructions for disassembling and assembling the travel motor of a 329E L Excavator. It lists the required tools and presents 28 steps to fully disassemble the travel motor by removing components like the head, brake piston, plates, seals, bearings and housing covers. The 28 steps of assembly are then described to reinstall these components in reverse order using the appropriate tools, lubricants, and torques. Key steps include removing and installing retaining rings, seals, bearings and repositioning marked components in their original locations.
Caterpillar cat 329 e l excavator (prefix zcd) service repair manual (zcd0000...fikkskmmdm
This document provides instructions for disassembling and assembling the travel motor of a 329E L excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for each part removal and installation. The process involves removing 28 different components including seals, springs, plates, pistons, and bearings. Proper alignment and lubrication of parts is emphasized during assembly to ensure correct functioning of the travel motor.
Caterpillar Cat 329E L Excavator (Prefix RLD) Service Repair Manual (RLD00001...jdjkskmikdkmd
This document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components like the head, brake piston, rotating assembly, seals and bearings. The assembly section then lists the components and provides the reverse steps to reinstall components and ensure proper alignment using tools and lubricants.
Similar to Caterpillar Cat 336D L Excavator (Prefix W3K) Service Repair Manual (W3K00001 and up).pdf (6)
Caterpillar Cat 325C FM EXCAVATOR (Prefix Y4P) Service Repair Manual (Y4P0000...ufs89eodkdmdm
This document provides instructions for disassembling and assembling the final drive of a 325C FM excavator. It lists the required tools and parts. The disassembly procedure involves removing over 30 components of the final drive including sprockets, gears, seals, plates, and housings. Detailed illustrations are provided to show how to remove each part correctly. The assembly procedure is not included.
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, and piston assemblies. Proper cleaning and identification of parts is emphasized to ensure correct reassembly. Tools required are listed in a table.
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...ufs89eodkdmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...ufs89eodkdmdm
The document provides instructions for assembling a travel motor on an excavator. It details 27 steps including installing seals, springs, pistons and other components into the motor housing. The motor is then installed onto the final drive assembly and excavator frame using bolts. Proper lubrication and torque specifications are emphasized to correctly assemble the travel motor.
1. The document provides installation instructions for an implement pump on a D8T track-type tractor. It describes 34 steps for installing various parts like valves, springs, seals and bearings into the pump housing.
2. Precautions are provided to ensure fluids are contained and parts are cleaned before assembly. Tools required are listed. Lubrication and heating of some parts is specified before installation.
3. Once assembled, the pump is attached to the tractor using bolts and hoses are connected to the manifold and slip joints.
This document provides instructions for removing and installing the front housing of a C27 Industrial Engine. The removal procedure involves detaching various components from the front of the engine like the water pump, oil filter housing, and brackets. Tools are required to remove some parts. The installation procedure specifies applying sealant, positioning the front housing and gasket, and installing bolts and other parts in the reverse order of removal. Tightening torques are provided for the bolts.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C9 Industrial Engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing a unit injector from the cylinder head
The procedures describe draining fluids, removing bolts and hoses, cleaning parts, replacing seals, and torquing fasteners to the specified values. Special tools are listed for many of the removal and installation steps.
This document provides instructions for removing and installing inlet and exhaust valves on a C27 Industrial Engine. It describes:
- Using a valve spring compressor tool to remove the valve springs and valve spring retainers.
- Inspecting the valves and checking the spring force.
- Lubricating the valve stems before installation and compressing the springs with a tool to install the retainers.
- Cautions for wearing protective equipment when working with springs to avoid injury from parts propelled by the springs.
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
This document provides instructions for removing and installing the engine oil filter base and oil cooler on a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Reversing the removal procedures for installation, including applying oil to seals and tightening bolts in a specific sequence
1) The document provides instructions for removing and installing various components of a Caterpillar C9.3 industrial engine, including disconnecting snap-to-connect fittings, removing and installing a muffler, and removing and installing a fuel priming pump and fuel filter base.
2) The procedures include illustrations showing the components and numbered steps for disassembly and reassembly. Safety warnings are provided at the beginning regarding relieving pressures before disconnection.
3) Torque specifications and required tools are listed for relevant installation steps.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
This document provides instructions for removing and installing the engine oil filter base and oil cooler on a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Reversing the removal procedures for installation, including applying oil to seals and tightening bolts in a specific sequence
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...ufs89eodkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 345D L Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pins, bearing, and piston assemblies. Special care must be taken to clean parts and ensure they are reinstalled in their original locations. Proper assembly prevents damage and contamination of parts.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and over 15 additional parts. The goal is to allow maintenance and repair of these core powertrain systems.
Caterpillar Cat 345D L Excavator (Prefix RGD) Service Repair Manual (RGD00001...ufs89eodkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, plates, seals, pins, and piston assemblies. The instructions describe cleaning parts and ensuring they are reinstalled in their original locations to properly reassemble the travel motor.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...ufs89eodkdmdm
This document provides instructions for removing and installing various engine components on a 345D L Excavator, including:
1. The rear gear group, which involves removing several gears, seals, and bearings.
2. The flywheel, which requires lifting equipment and guide studs due to its weight.
3. The crankshaft rear seal, which is removed after removing the flywheel. Precise instructions are provided along with safety notices.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
2. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
4/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g00887302
6. Remove O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 3 g00887311
7. Remove O-ring seals (6) . Remove springs (7) .
Illustration 4 g00887331
5/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 5 g00890074
This is an example of the use of Tooling (B) .
8. Place a shop towel over brake piston (8) . Retain brake piston (8) with Tooling (B) . Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y) . Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
6/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g00887355
11. Remove plates (13) and friction discs (14) .
Illustration 8 g00887401
Illustration 9 g00887405
12. Install Tooling (C) into shaft (15) . Use a prybar to remove the rotating assembly (16) from
the housing.
7/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 13. Remove Tooling (C) from shaft (15) .
Illustration 10 g00887424
14. Remove shaft (15) from rotating assembly (16) .
Illustration 11 g00887426
15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15) .
8/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 12 g00887445
16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
Illustration 13 g00887463
17. Rotate shaft (15) . Install shaft (15) into a suitable press. Install Tooling (E) . Remove
bearing race (19) from shaft (15) .
Illustration 14 g00887501
18. Remove cam plate (20) from barrel assembly (21) .
9/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g00887520
19. Remove piston assemblies and retainer plate (22) from barrel assembly (21) .
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g00887558
20. Remove ball (23) and springs (24) .
10/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP5...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g00887578
21. Remove bearing (25) .
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27) .
24. Remove seal (28) .
Illustration 19 g00887619
25. Remove bolts (29) and cover (30) .
11/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP5...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g00887729
26. Remove seal (31) and backup ring (32) .
Illustration 21 g00887754
27. Remove piston actuator (33) and seal (34) .
Illustration 22 g00887762
28. Remove O-ring seal (35) from the housing of the travel motor.
12/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP5...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR W3K
Configuration: 336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i03124523
Travel Motor - Assemble
SMCS - 4351-016
S/N - B6H1-UP
S/N - DTS1-UP
S/N - EAH1-UP
S/N - EDX1-UP
S/N - EFT1-UP
S/N - ERN1-UP
S/N - FAR1-UP
S/N - FFK1-UP
S/N - GGE1-UP
S/N - GGH1-UP
S/N - HAS1-UP
S/N - HHK1-UP
S/N - J2F1-UP
S/N - JBT1-UP
S/N - JLP1-UP
S/N - JTN1-UP
1/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. S/N - WRK1-UP
S/N - XBH1-UP
S/N - YCF1-UP
S/N - ZCT1-UP
S/N - ZML1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded Rod M12 x 1.75 X 250 mm (10 in) long 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G 9S-3263 Thread Lock Compound -
Note: Replace all O-ring seals and gaskets. Apply a light film of"10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause trouble later. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
3/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33) .
Illustration 3 g00887729
3. Install backup ring (32) and seal (31) .
4/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 4 g00887619
4. Install cover (30) and bolts (29) . Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of seal (28) . Use Tooling (E) in order to install
seal (28) .
6. Use Tooling (F) in order to install retaining ring (27) .
5/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 6 g00887578
7. Rotate the housing.
8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25) .
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel. Install ball (23) onto springs (24) .
6/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 8 g00887520
11. Install piston assemblies and retainer plate (22) into barrel assembly (21) .
Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Install cam plate (20) onto barrel assembly (21) .
7/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15) .
Illustration 11 g00887426
14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15) .
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15) .
Note: Bearing race (18) must contact retaining ring (17) .
8/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 13 g00887405
16. Install Tooling (C) into shaft (15) . Install shaft (15) into rotating assembly (16) .
17. Place the pump housing into Tooling (A) .
Illustration 14 g00887401
18. Use Tooling (C) in order to install rotating assembly (16) into the housing.
Illustration 15 g00887501
9/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 16 g00887578
19. The notches in cam plate (20) must align with keys (26) . The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
10/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP5...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8) .
24. Install brake piston (8) into the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level in
order to prevent damage to the O-ring seals.
11/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP5...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6) .
Illustration 21 g00887302
26. Install O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 22 g00887295
27. Install head (2) onto the body of the travel motor.
12/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP5...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1) . Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By: Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu May 21 21:36:45 UTC+0800 2020
13/13
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP5...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR W3K
Configuration: 336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i03808350
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded Rod 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/4
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g00878123
2. Install new O-ring seal (6) . Apply clean hydraulic oil on the O-ring seal.
Illustration 2 g00707267
3. Attach a suitable lifting device to travel motor (4) , as shown.
4. The weight of the travel motor is approximately 57 kg (125 lb).
Illustration 3 g00878121
2/4
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 5. Carefully install travel motor (4) onto Tooling (A) . Slide the travel motor into the final
drive.
6. Install one of three bolts (5) that secures the travel motor to the final drive.
7. Remove Tooling (A) .
Illustration 4 g00707275
Typical example
8. Install remaining bolts (2) .
9. Connect hose assembly (3) . Connect hose assembly (1) .
10. Fill the final drive with oil.
ReferenceRefer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
ReferenceRefer to Operation and Maintenance Manual, "Final Drive Oil Level - Check" for
the correct filling procedure.
11. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
12. Obtain a hydraulic oil sample from the main S·O·S port.
ReferenceRefer to Operation and Maintenance Manual, "Sampling Interval and Location of
Sampling Valve" for the correct location.
13. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system.
ReferenceRefer to Contamination Control Guidelines, SEBF8436, "Hydraulic System
Flushing Procedure for 322C Hydraulic Excavators" for further information.
3/4
336D L Excavator W3K00001-UP (MACHINE) POWERED BY C9 Engine(SEBP537...
2020/5/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...