Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual (J6D00001 and up).pdf

Service Repair Manual
Models
336D L Excavator

Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336D L MOBILE HYD POWER UNIT J6D
Configuration: 336D L Mobile Hydraulic Power Unit J6D00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i05271119
Final Drive - Disassemble
SMCS - 4050-015
S/N - GGH1-UP
S/N - HHK1-UP
S/N - J6D1-UP
S/N - JRX1-UP
S/N - NBN1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 3
B 8T-0226 Bolt 2
C
5F-7366 Forcing Screw 1
1A-1935 Full Nut 1
D 150-1782 Crossblock 1
E 5P-8713 Plate 1
F 1P-0510 Driver Gp 1
G 384-8910 Torque Wrench 1
1/12
336D L Mobile Hydraulic Power Unit J6D00001-UP (MACHINE) POWERED BY C...
2020/9/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...

3S-6224 Electric Hydraulic Pump Gp 1
8H-8535 1 1/4 Socket 1
H 1U-9895 Crossblock 1
J 126-7183 Crossblock 1
K c M14 X 2.0 X 254mm -
L 417-6239 Lifting Adapter 1
Illustration 1 g03032222
1. Use Tooling (A) and a suitable lifting device in order to position final drive (1) . The weight
of final drive (1) is approximately 435 kg (960 lb).
2. Remove bolts (2) .
2/12
2020/9/1

https://www.aservicemanualpdf.com/
My Dear Friend! Thank you very
much for visiting. Full manual if
required, please enter the
following URL into your browser.
https://www.aservicemanualpdf.com/

3. Use Tooling (B) and suitable pry bar to remove flange (3) . Remove o-ring (4) from flange
(3) .
3/12
2020/9/1

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Use Tooling (C) , (D) , (E) , and (F) to compress spring retainer (6) .
5. Remove retaining ring (5) .
6. Remove spring retainer (6) .
7. Remove springs (7) and piston (8) . Remove gear (12) (not shown) .
4/12
2020/9/1

8. Remove discs (9) and plates (10) .
9. Remove seals (11) and gear (12) .
5/12
2020/9/1

10. Use Tooling (A) and a suitable lifting device to reposition final drive (1) . The weight of
final (1) is approximately 435kg (960 lb).
11. Remove bolts (14) . Use a suitable lifting device to remove cover (13) .
12. The weight of cover (13) is approximately 73 kg (160 lb).
6/12
2020/9/1

13. Remove o-ring (15) from cover (13) .
14. Remove gear assembly (16) .
7/12
2020/9/1

15. Remove gear (18) from shaft (17) .
16. Remove gear assembly (19) .
8/12
2020/9/1

17. Remove gear (20) .
18. Use Tooling (G) to remove bolts (21) . Bolts (21) may need the temperature raised for
assisting removal. (Note: disregard bolts (21) .)
19. Remove housing (22) .
9/12
2020/9/1

20. Remove gear assemblies (23) .
21. Compress retaining ring (25) in order to remove plate assembly (24) .
22. Use Tooling (C) , (H, and) (J) in order to separate housing (26) from hub (27) .
10/12
336D L Mobile Hydraulic Power Unit J6D00001-UP (MACHINE) POWERED BY ...
2020/9/1

23. Remove race (28) and use Tooling (A) and a suitable lifting device to lift off housing (26) .
The housing (26) weighs approximately 113 kg (250 lb)
24. Remove seal (29) and bearing assemblies (30) .
11/12
2020/9/1

25. Remove race (32) and seal (31) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 1 14:52:55 UTC+0800 2020
12/12
2020/9/1

Shutdown SIS
Previous Screen
i05271457
Final Drive - Assemble
SMCS - 4050-016
S/N - GGH1-UP
S/N - HHK1-UP
S/N - J6D1-UP
S/N - JRX1-UP
S/N - NBN1-UP
Assembly Procedure
Table 1
Required Tools
A 138-7575 Link Bracket 3
B 8T-0226 Bolt 2
D 150-1782 Crossblock 1
E
1P-0520 Driver Gp 1
1P-0510 Driver Gp
F 123-8527 Adapter 1
G 132-8122 TorqueWrench 1
3S-6224 Electric Hydraulic Pump Gp 1
1/11
2020/9/1

8H-8535 1 1/4 Socket 1
J 126-7183 Crossblock 1
L 417-6239 Lifting Adapter 1
M - Loctite 242 -
N 8T-9206 Duo Cone Installer As 1
1. Install spacer (33) . Use Tooling (N) to install seal (31) . Install race (32) .
2. Use Tooling (N) to install seal (29) . Install bearing assemblies (30) .
2/11
2020/9/1

3. Use Tooling (A) and a suitable lifting device to position housing (26) onto the hub (27) .
The weight of housing (26) is approximately 113 kg (250 lb). Install race (28) .
4. Compress retaining ring (25) in order to install plate assembly (24) .
3/11
2020/9/1

5. Install gear assemblies (23) .
6. Install housing (22) .
7. Install bolts (21) . Use Tooling (G) and tighten bolts (21) to a torque of 1440 N·m (1062 lb
ft).
4/11
2020/9/1

8. Install gear (20) .
9. Install gear assembly (19) .
5/11
2020/9/1

10. Position shaft (17) in gear assembly (16) and install gear (18) .
11. Install gear assembly (16) .
6/11
2020/9/1

12. Install o-ring (15) onto cover (13) .
13. Use Tooling (L) to position cover (13) .
14. Apply Tooling (M) to bolts (14) and install. Tighten bolts (14) to a torque of 190 N·m (140
lb ft).
7/11
2020/9/1

15. Use Tooling (A) and a suitable lifting device to reposition final drive (1) . The weight of
final drive (1) is approximately 435 kg (960 lb).
16. Install gear (12) ( not shown ) and seals (11) .
8/11
2020/9/1

17. Install discs (9) and plates (10) .
18. Install piston (8) and springs (7) .
9/11
2020/9/1

Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Position spring retainer (6) and retaining ring (5) .
20. Use Tooling (C) , (D) , (E) , and (F) to compress spring retainer (6) in order to install
retaining ring (5) .
10/11
2020/9/1

21. Install O-ring (4) . Use Tooling (B) to position flange (3) .
22. Install bolts (2) . Tighten bolts (2) to a torque of 215 N·m (159 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 1 14:53:51 UTC+0800 2020
11/11
2020/9/1

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Shutdown SIS
Previous Screen
i02451126
Final Drive and Travel Motor - Remove
SMCS - 4050-011; 4351-011
Removal Procedure
Table 1
Required Tools
A
5P-0306 Vacuum Transducer 1
FT-1115 Vacuum Cap 1
6V-4142 Fitting 1
5K-5068 Fitting 1
B 1U-9200 Lever Puller Hoist 1
C 138-7573 Link Bracket 1
Note: Put identification marks on all hose assemblies, fittings and ports so that all the components
can be reassembled in the original configuration. Plug all of the hose assemblies and cap all of the
fittings. This helps to prevent fluid loss and this helps to keep contaminants from entering the
system.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/6
2020/9/1

before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
2/6
2020/9/1

1. Remove bolts (1) and cover (2).
2. Separate the track. Refer to Disassembly and Assembly, "Track - Seperate".
3. Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach
an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This
procedure will pull vacuum on the hydraulic system.
4. Disconnect hose assemblies (3) and remove fitting (4).
3/6
2020/9/1

Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual (J6D00001 and up).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual (J6D00001 and up).pdf

Similar to Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual (J6D00001 and up).pdf (20)

More from zatao0179249295

More from zatao0179249295 (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual (J6D00001 and up).pdf