This document provides instructions for disassembling and assembling the piston pump of a 336D L excavator. It outlines 30 steps to disassemble the pump into its individual components like housing, springs, pistons and seals. The assembly section then lists 29 steps to rebuild the pump, noting things like tool requirements, heating/cooling parts, and ensuring proper end play and shim thickness. Personal safety warnings are included throughout regarding spring-loaded components.
Caterpillar cat 336 d l excavator (prefix dts) service repair manual (dts0000...fjskkkdmem
The document provides step-by-step instructions for disassembling and assembling the piston pump of a 336D L excavator. It lists 30 steps for disassembly, removing components like bolts, seals, springs, and housings. It then lists 30 steps for assembly, installing the components in reverse order while noting things like tool usage and temperature requirements. The overall document provides a detailed technical procedure for maintenance and repair of the excavator's piston pump.
Caterpillar cat 336 d l excavator (prefix dts) service repair manual (dts0000...fjskemdme
This document provides disassembly and assembly instructions for the piston pump (hydraulic fan) on a Caterpillar 336D L excavator. It outlines 30 steps to disassemble the pump, removing components like housing, springs, pistons, bearings and seals. It then describes 26 steps for reassembling the pump, providing notes on cleaning parts and checking clearances. Finally, it describes installing the reassembled pump back onto the excavator and refilling the hydraulic system.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix KDJ) Service Repair Manu...shibi1322
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) used in Caterpillar 336D L and 336D LN excavators. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. It also provides illustrations matching each step for clarity.
Caterpillar cat 336 d l excavator (prefix kdj) service repair manual (kdj0000...cdfxssw
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) used in Caterpillar 336D L and 336D LN excavators. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix KDJ) Service Repair Manu...8foskkdjdkdm3e
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) used in Caterpillar 336D L and 336D LN excavators. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. It also provides illustrations matching each step for clarity.
Caterpillar cat 336 d ln excavator (prefix kdj) service repair manual (kdj000...cdfxssw
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) used in Caterpillar 336D L and 336D LN excavators. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. It also provides illustrations matching each step for clarity.
Caterpillar Cat 345C and 345C L Hydraulic Excavator (Prefix PJW) Service Repa...fijsekkdmdm2w
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, applying anti-seize compound, installing various seals and gears, and adjusting bearing preload using shims. Precision is required to prevent damage to seals and ensure proper engagement of gears. Lifting devices and care are needed due to components weighing up to 127 kg.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar cat 336 d l excavator (prefix dts) service repair manual (dts0000...fjskkkdmem
The document provides step-by-step instructions for disassembling and assembling the piston pump of a 336D L excavator. It lists 30 steps for disassembly, removing components like bolts, seals, springs, and housings. It then lists 30 steps for assembly, installing the components in reverse order while noting things like tool usage and temperature requirements. The overall document provides a detailed technical procedure for maintenance and repair of the excavator's piston pump.
Caterpillar cat 336 d l excavator (prefix dts) service repair manual (dts0000...fjskemdme
This document provides disassembly and assembly instructions for the piston pump (hydraulic fan) on a Caterpillar 336D L excavator. It outlines 30 steps to disassemble the pump, removing components like housing, springs, pistons, bearings and seals. It then describes 26 steps for reassembling the pump, providing notes on cleaning parts and checking clearances. Finally, it describes installing the reassembled pump back onto the excavator and refilling the hydraulic system.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix KDJ) Service Repair Manu...shibi1322
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) used in Caterpillar 336D L and 336D LN excavators. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. It also provides illustrations matching each step for clarity.
Caterpillar cat 336 d l excavator (prefix kdj) service repair manual (kdj0000...cdfxssw
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) used in Caterpillar 336D L and 336D LN excavators. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix KDJ) Service Repair Manu...8foskkdjdkdm3e
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) used in Caterpillar 336D L and 336D LN excavators. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. It also provides illustrations matching each step for clarity.
Caterpillar cat 336 d ln excavator (prefix kdj) service repair manual (kdj000...cdfxssw
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) used in Caterpillar 336D L and 336D LN excavators. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. It also provides illustrations matching each step for clarity.
Caterpillar Cat 345C and 345C L Hydraulic Excavator (Prefix PJW) Service Repa...fijsekkdmdm2w
The document provides assembly instructions for a final drive on an excavator model 345C. It involves 17 steps including installing bearing cups, applying anti-seize compound, installing various seals and gears, and adjusting bearing preload using shims. Precision is required to prevent damage to seals and ensure proper engagement of gears. Lifting devices and care are needed due to components weighing up to 127 kg.
Caterpillar Cat 345C and 345C L Excavator (Prefix TBA) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, pistons and housing pieces. Identification marks should be made on parts for reassembly. Cleaning is important to prevent contamination. The assembly procedure is not described.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336E and 336E L Excavator (Prefix KED) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for assembling a travel motor on an excavator. It describes 27 steps to assemble internal components like seals, springs, and bearings. These components include pistons, a cam plate, and a rotating assembly. The final steps connect the travel motor to the final drive and install exterior covers. Proper assembly requires using the correct tools and lubricants, and ensuring parts are aligned and torques are set correctly.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to disassemble the pump by removing components like bolts, sensors, valves, springs, pistons, gears, and bearings. The assembly section lists 48 steps to reinstall these components in reverse order, noting the need to heat some bearings before installation and ensure proper placement of pins, seals, and other parts. Precautions are provided for releasing spring forces. Required tools include various pliers, pins, and links to aid in removal and installation of components.
Caterpillar Cat 330F and 330F L Excavator (Prefix GHT) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling a 330F excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, brake piston, rotating assembly, pistons, seals, and other parts. Tools required include retaining ring pliers, a bearing puller, bolts, threaded rods, and other hardware. Safety precautions are provided to release spring forces carefully.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling the travel motor on a 336D2L excavator. It describes 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, springs, seals, relief valves, plugs, and more. Precautions are provided to watch for spring forces and contain fluids. Tools needed include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Reassembly will follow the disassembly steps in reverse order.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and over 15 additional parts. The goal is to allow maintenance and repair of these core powertrain systems.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 336D L Excavator (Prefix JBF) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for installing a unit injector sleeve on a Caterpillar C9 engine. It lists the required tools and gives step-by-step details for cleaning the sleeve and cylinder head bore, applying seals and retaining compound, and installing the sleeve using a hammer and installer tool. Proper installation is important to prevent leaks that could cause low pressure or excess oil consumption.
Caterpillar Cat 926 and 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing the cylinder head assembly on a 3204 vehicular engine. It describes:
1) Removing the cylinder head assembly by loosening hoses, removing bolts, and lifting it off with a hoist.
2) Cleaning and installing a new gasket before lowering the cylinder head back onto the cylinder block and tightening bolts in a specific sequence and torque.
3) Checking the flatness of the cylinder head and block surfaces during installation.
This document provides instructions for disassembling and assembling the torque converter and transmission of a Caterpillar 938F wheel loader. It details removing over 40 individual parts in 21 steps to disassemble the torque converter. A further 44 steps describe disassembling the transmission by removing components like shafts, gears, seals, and clutches. Precise tools and lifting devices are specified to carefully remove heavy parts. Reassembly is outlined in reverse order with notes to check components for wear and replace as needed.
Caterpillar Cat 325C and 325C L Excavator (Prefix BKW) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs to clean all parts thoroughly, apply lubricants, and install the parts in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Tools required include a transmission repair stand, link brackets, retaining ring pliers, and other specialized tools.
This document provides instructions for disassembling and assembling the piston pump of a 623G wheel scraper. Some key steps include:
1. Marking all mating components for alignment during assembly.
2. Removing various seals, springs, spools, and other internal parts from the pump housing and head.
3. Checking the preload on bearings during assembly by measuring clearance between the pump head and housing.
4. Cleaning all parts thoroughly before assembly and applying a light oil film. Precise alignment of marked components is important.
This document provides instructions for disassembling and assembling axle shaft assemblies for a 938F wheel loader. It describes removing components like the axle housing groups, axle shaft assembly, planetary carrier assembly, and installing new components in reverse order. Key steps include using various tools to remove retaining rings, planetary gears, and installing new bearings and seals at specified temperatures while ensuring proper torque specifications are met.
The document provides instructions for removing and installing fuel injection pumps on a Caterpillar 3406C diesel engine. Key steps include using various tools to hold components in place, loosening and removing bushings, seals and pumps. Reinstallation involves aligning pins and slots, installing spacers and seals correctly, and checking rack travel measurements to ensure proper installation. The document also describes disassembling and assembling the fuel injection pumps and fuel injection pump housing.
The document provides step-by-step instructions for disassembling and assembling the final drives of a 350L excavator. Key steps include removing the final drives and travel motors, disassembling the internal components of the final drives which include multiple planetary gear sets, carriers, and a sun gear, and then reassembling the final drives in reverse order. Proper cleaning, application of lubricants, and torque specifications are noted throughout to ensure correct reassembly.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, brake piston, rotating group, and seals. The instructions describe taking identifying marks on parts and cleaning components to prevent contamination. Reassembly is done in reverse order.
Caterpillar Cat 350 and 350 L Excavator (Prefix 8HK) Service Repair Manual In...fijsekkdmdm2w
This document provides instructions for removing and installing various engine components on a 350-A EXCAVATOR 8HK excavator with a 3306 engine, including:
1) Removing the cylinder head which requires first removing the fuel injection lines and exhaust manifold.
2) Instructions for disassembling, assembling, and installing the rocker shaft and pushrods.
3) Procedures for removing, disassembling, assembling, and installing the compression brake on the excavator.
Caterpillar Cat 336F and 336F L Excavator (Prefix NBL) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety cautions are provided throughout for parts under spring tension.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, which powers a 345D L excavator. The procedures include removing the electric starting motor, flywheel, rear crankshaft seal, and other rear gear components. Detailed illustrations show the components and tools used. Precautions are provided to properly support heavy components and contain fluids.
Caterpillar Cat 336E and 336E L Excavator (Prefix KED) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for assembling a travel motor on an excavator. It describes 27 steps to assemble internal components like seals, springs, and bearings. These components include pistons, a cam plate, and a rotating assembly. The final steps connect the travel motor to the final drive and install exterior covers. Proper assembly requires using the correct tools and lubricants, and ensuring parts are aligned and torques are set correctly.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly procedure includes removing components like bolts, seals, gears, and housings. The 21 step assembly procedure describes installing these components in reverse order, noting precautions like wearing protective equipment and using torque wrenches to specified settings. Tools required include link brackets, crossblocks, drivers, sockets, and lifting adapters.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to disassemble the pump by removing components like bolts, sensors, valves, springs, pistons, gears, and bearings. The assembly section lists 48 steps to reinstall these components in reverse order, noting the need to heat some bearings before installation and ensure proper placement of pins, seals, and other parts. Precautions are provided for releasing spring forces. Required tools include various pliers, pins, and links to aid in removal and installation of components.
Caterpillar Cat 330F and 330F L Excavator (Prefix GHT) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for disassembling a 330F excavator travel motor. It describes 28 steps to disassemble the various components of the travel motor, including removing the head assembly, brake piston, rotating assembly, pistons, seals, and other parts. Tools required include retaining ring pliers, a bearing puller, bolts, threaded rods, and other hardware. Safety precautions are provided to release spring forces carefully.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling the travel motor on a 336D2L excavator. It describes 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, springs, seals, relief valves, plugs, and more. Precautions are provided to watch for spring forces and contain fluids. Tools needed include a transmission repair stand, lifting eye assembly, driver group, and other specialized tools. Reassembly will follow the disassembly steps in reverse order.
This document provides instructions for disassembling and assembling the torque converter and transmission of a 938F wheel loader. It describes removing over 20 components of the torque converter including the transmission cover, driver gear, stator carrier, and retaining rings. It then details disassembling the transmission by removing the shafts, gears, clutch plates, seals, and over 15 additional parts. The goal is to allow maintenance and repair of these core powertrain systems.
Caterpillar Cat 325C and 325C L Excavator (Prefix BMM) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly. Key steps include:
1. Marking the final drive for alignment and removing it from the machine.
2. Removing the cover, gears, spacers, and carrier assemblies.
3. Disassembling the carrier assemblies by pressing out pins and removing gears and bearings.
4. Removing the ring gears from the main housing after lifting with slings.
Caterpillar Cat 336D L Excavator (Prefix JBF) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for installing a unit injector sleeve on a Caterpillar C9 engine. It lists the required tools and gives step-by-step details for cleaning the sleeve and cylinder head bore, applying seals and retaining compound, and installing the sleeve using a hammer and installer tool. Proper installation is important to prevent leaks that could cause low pressure or excess oil consumption.
Caterpillar Cat 926 and 926E WHEEL LOADER (Prefix 8NB) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for removing and installing the cylinder head assembly on a 3204 vehicular engine. It describes:
1) Removing the cylinder head assembly by loosening hoses, removing bolts, and lifting it off with a hoist.
2) Cleaning and installing a new gasket before lowering the cylinder head back onto the cylinder block and tightening bolts in a specific sequence and torque.
3) Checking the flatness of the cylinder head and block surfaces during installation.
This document provides instructions for disassembling and assembling the torque converter and transmission of a Caterpillar 938F wheel loader. It details removing over 40 individual parts in 21 steps to disassemble the torque converter. A further 44 steps describe disassembling the transmission by removing components like shafts, gears, seals, and clutches. Precise tools and lifting devices are specified to carefully remove heavy parts. Reassembly is outlined in reverse order with notes to check components for wear and replace as needed.
Caterpillar Cat 325C and 325C L Excavator (Prefix BKW) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs to clean all parts thoroughly, apply lubricants, and install the parts in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Tools required include a transmission repair stand, link brackets, retaining ring pliers, and other specialized tools.
This document provides instructions for disassembling and assembling the piston pump of a 623G wheel scraper. Some key steps include:
1. Marking all mating components for alignment during assembly.
2. Removing various seals, springs, spools, and other internal parts from the pump housing and head.
3. Checking the preload on bearings during assembly by measuring clearance between the pump head and housing.
4. Cleaning all parts thoroughly before assembly and applying a light oil film. Precise alignment of marked components is important.
This document provides instructions for disassembling and assembling axle shaft assemblies for a 938F wheel loader. It describes removing components like the axle housing groups, axle shaft assembly, planetary carrier assembly, and installing new components in reverse order. Key steps include using various tools to remove retaining rings, planetary gears, and installing new bearings and seals at specified temperatures while ensuring proper torque specifications are met.
The document provides instructions for removing and installing fuel injection pumps on a Caterpillar 3406C diesel engine. Key steps include using various tools to hold components in place, loosening and removing bushings, seals and pumps. Reinstallation involves aligning pins and slots, installing spacers and seals correctly, and checking rack travel measurements to ensure proper installation. The document also describes disassembling and assembling the fuel injection pumps and fuel injection pump housing.
The document provides step-by-step instructions for disassembling and assembling the final drives of a 350L excavator. Key steps include removing the final drives and travel motors, disassembling the internal components of the final drives which include multiple planetary gear sets, carriers, and a sun gear, and then reassembling the final drives in reverse order. Proper cleaning, application of lubricants, and torque specifications are noted throughout to ensure correct reassembly.
Caterpillar Cat 345D L Excavator (Prefix RAE) Service Repair Manual Instant D...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 345D L excavator. It lists the required tools and gives step-by-step instructions for removing components like the head, brake piston, rotating group, and seals. The instructions describe taking identifying marks on parts and cleaning components to prevent contamination. Reassembly is done in reverse order.
Caterpillar Cat 350 and 350 L Excavator (Prefix 8HK) Service Repair Manual In...fijsekkdmdm2w
This document provides instructions for removing and installing various engine components on a 350-A EXCAVATOR 8HK excavator with a 3306 engine, including:
1) Removing the cylinder head which requires first removing the fuel injection lines and exhaust manifold.
2) Instructions for disassembling, assembling, and installing the rocker shaft and pushrods.
3) Procedures for removing, disassembling, assembling, and installing the compression brake on the excavator.
Caterpillar Cat 336F and 336F L Excavator (Prefix NBL) Service Repair Manual ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. It begins by listing the required tools. The 30 step disassembly procedure describes how to remove components like springs, seals, plates, and housing pieces. The 28 step assembly procedure describes how to reinstall these components in reverse order and includes notes on lubrication and proper positioning. Personal safety cautions are provided throughout for parts under spring tension.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR DTS
Configuration: 336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02732014
Piston Pump (Hydraulic Fan) - Disassemble
SMCS - 1387-015-QP; 5070-015-HFN
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
B 1P-1857 Retaining Ring Pliers 1
C 9S-9152 Bearing Puller Gp 1
Start By:
a. Remove the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Hydraulic
Fan) - Remove".
1/9
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove housing (21), O-ring seal (20), shim (19), spring (18), spring (17), poppet (16), and
spool (15) from housing (2).
5. Cartridge (14), O-ring seal (13), backup ring (11), O-ring seal (12), spool (10), retainer (9),
spring (8), and retainer (7).
6. Remove screw (6) from housing (2).
Illustration 5 g01212900
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7. Remove bolts (22) and head (23).
3/9
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 6 g01212901
8. Remove O-ring seals (24), port plate (25), and bearing cup (26).
Illustration 7 g01212902
9. Remove spring (27), piston (29), and O-ring seal (28).
Illustration 8 g01212903
10. Remove piston (30).
4/9
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 9 g01212904
11. Remove bearing cone (31).
Illustration 10 g01212905
12. Remove shim (33) and rotating group (32).
Illustration 11 g01212906
13. Remove pistons (34), retainer (35), and bearing (36).
5/9
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 12 g01212907
14. Remove pins (37) from barrel (38).
Illustration 13 g01212908
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
15. Use Tooling (A), Tooling (B), and a suitable press in order to remove retaining ring (39)
from barrel (38).
6/9
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 14 g01373818
16. Remove shim (42), spring (41), and shim (40) from barrel (38).
Illustration 15 g01212910
17. Remove swashplate (43).
Illustration 16 g01212911
18. Remove shaft (45), bearing cone (46), and bearings (44).
7/9
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 17 g01212912
19. Use Tooling (C) in order to remove bearing cone (46) from shaft (45).
Illustration 18 g01212913
20. Use Tooling (B) in order to remove retaining ring (47).
21. Remove lip seal (48).
Illustration 19 g01212915
22. Remove bearing cup (49).
8/9
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR DTS
Configuration: 336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02732015
Piston Pump (Hydraulic Fan) - Assemble
SMCS - 1387-016-QP; 5070-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1857 Retaining Ring Pliers 1
D 8T-5096 Dial Indicator Gp 1
Illustration 1 g01212915
1. Lower the temperature of bearing cup (49). Install bearing cup (49).
1/11
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 2 g01212913
2. Install lip seal (48).
3. Use Tooling (B) in order to install retaining ring (47).
Illustration 3 g01213404
4. Raise the temperature of bearing cone (46).
5. Install bearing cone (46) onto shaft (45).
Illustration 4 g01213405
6. Install bearing cone (46), shaft (45), and bearing cone (31).
2/11
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 5 g01213407
7. Lower the temperature of bearing cone (26). Install bearing cone (26).
Illustration 6 g01212900
8. Position head (23) onto the housing.
9. Install bolts (22).
Illustration 7 g01213409
10. Use Tooling (D) in order to determine the end play of shaft (45).
3/11
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 8 g01212900
11. Remove bolts (22) and head (23).
Illustration 9 g01213405
12. Remove bearing cone (31).
Illustration 10 g01213433
13. Install bearings (44).
4/11
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 11 g01212910
14. Install swashplate (43).
Illustration 12 g01373818
15. Install shim (40), spring (41), and shim (42) to barrel (38).
Illustration 13 g01212908
5/11
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
16. Use Tooling (A), Tooling (B), and a suitable press in order to install retaining ring (39) into
barrel (38).
Illustration 14 g01212907
17. Install pins (37) into barrel (38).
Illustration 15 g01212906
18. Install bearing (36), retainer (35), and pistons (34).
6/11
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 16 g01212905
19. Install rotating group (32) and shim (33).
Note: Shim thickness was determined on Step 9.
Illustration 17 g01212904
20. Install bearing cone (31).
Illustration 18 g01212903
21. Install piston (30).
7/11
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 19 g01212902
22. Install spring (27), piston (29), and O-ring seal (28).
Illustration 20 g01213436
23. Install O-ring seals (24) and port plate (25).
Illustration 21 g01212900
8/11
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
24. Install head (23) and bolts (22).
Illustration 22 g01212898
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
25. Install spool (15), poppet (16), spring (17), spring (18), shim (19), O-ring seal (20), and
housing (21) into housing (2).
26. Install retainer (7), spring (8), retainer (9), spool (10), O-ring seal (12), backup ring (11), O-
ring seal (13), and cartridge (14).
27. Install screw (6) into housing (2).
9/11
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 23 g01212897
28. Install coil (4) and nut (5).
Illustration 24 g01212896
29. Install O-ring seals (3).
Illustration 25 g01212895
30. Install controller (2) and bolts (1).
End By:
10/11
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP5...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. a. Install the piston pump. Refer to Disassembly and Assembly, "Piston Pump (Hydraulic Fan)
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 6 11:40:16 UTC+0800 2020
11/11
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP5...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR DTS
Configuration: 336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02424411
Piston Pump (Hydraulic Fan) - Install
SMCS - 1387-012-QP; 5070-012-HFN
Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01211400
1. Position piston pump (7) and install bolts (6).
2. Connect harness assembly (5).
3. Connect hose assemblies (3) and (4).
1/2
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 2 g01211399
4. Connect hose assembly (2).
Illustration 3 g01206719
5. Close door (1).
6. Fill the hydraulic system with oil. Refer to Operation and Maintenance Manual, "Refill
Capacities".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 6 11:41:12 UTC+0800 2020
2/2
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR DTS
Configuration: 336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415451
Piston Motor (Hydraulic Fan) - Remove
SMCS - 1386-011-QP; 5058-011-FM
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
Illustration 1 g01207415
1. Bend locking tabs (1) backward.
2. Remove bolts (2) and hub (3).
1/2
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 2 g01207416
3. Use a suitable lifting device to position fan motor assembly (4) onto suitable cribbing. The
weight of fan motor assembly (4) is approximately 68 kg (150 lb).
Illustration 3 g01207418
4. Attach a suitable lifting device to piston motor (5). The weight of piston motor (5) is
approximately 23 kg (50 lb).
5. Remove bolts (6) and fan motor (5).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 6 11:42:08 UTC+0800 2020
2/2
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR DTS
Configuration: 336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415272
Piston Motor (Hydraulic Fan) - Disassemble
SMCS - 1386-015-QP; 5058-015-FM; 5058-015-HFN
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9152 Bearing Puller Gp 1
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Start By:
a. Remove the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Remove".
1/7
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. Illustration 1 g01207275
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove bolts (1) and head (2).
Illustration 2 g01207276
2. Remove O-ring seal (3), port plate (4), and bearing cup (5).
Illustration 3 g01207278
2/7
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove plug (6), sleeve (7), poppet (8), spring (9), poppet (10), and O-ring seal (11).
Illustration 4 g01207279
4. Remove bearing cone (12).
Illustration 5 g01207280
5. Remove shim (13) and rotating group (14).
3/7
336D L Excavator DTS00001-UP (MACHINE) POWERED BY C9 Engine(SEBP538...
2020/5/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...