This document provides instructions for assembling and disassembling a travel motor on Caterpillar 336F L and 336F LN excavators. It lists the required tools and parts and includes illustrations of each step. The assembly procedure involves installing seals, springs, pistons, bearings, and other components in the proper order. The disassembly and removal process describes draining fluid, disconnecting hoses, and using lifting devices to remove the final drive and travel motor assembly.
Caterpillar cat 336 f l excavator (prefix zbj) service repair manual (zbj0000...fjsjekdmmeme
This document provides instructions for servicing the travel motor on Caterpillar 336F L and 336F LN excavators. It describes the disassembly and assembly procedures, which include 27 individual steps. The document lists required tools and includes illustrations to clarify each step. The summary is:
1. The document provides a service repair manual for Caterpillar 336F L and 336F LN excavators, outlining the process for travel motor disassembly and assembly in 27 steps.
2. Illustrations and lists of required tools accompany the step-by-step instructions.
3. Reassembly requires applying sealant and torquing bolts to the specified values.
Caterpillar cat 336 f l excavator (prefix ljy) service repair manual (ljy0000...fjkskedmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 336 f l excavator (prefix ssn) service repair manual (ssn0000...fjsjekdmmeme
This document provides disassembly and assembly instructions for a 336F L excavator travel motor. The disassembly process involves removing 30 components from the travel motor in a specific sequence. Safety precautions are outlined due to parts under spring tension. The assembly section describes installing 35 components back into the travel motor housing following the reverse of the disassembly order. Tools required are listed for both procedures.
Caterpillar cat 336 f l excavator (prefix dkf) service repair manual (dkf0000...fjsjekdmmeme
This document provides instructions for disassembling and assembling a travel motor for 336F L and 336F LN excavators powered by a C9.3 engine. The disassembly procedure involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly procedure instructs assembling the travel motor in the reverse order and notes to lubricate parts and install components in their original positions and orientations. Safety precautions are provided throughout regarding releasing spring forces and installing spring loaded parts.
The document provides instructions for removing and installing various components on a 336 excavator, including the cab, window wiper motor, and connecting the upper frame and undercarriage frame. It includes lists of required tools and sequential steps supported by illustrations. Safety procedures and torque specifications are noted.
Caterpillar cat 336 f l excavator (prefix wtz) service repair manual (wtz0000...fjsjekdmmeme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. The disassembly procedure involves 30 steps to remove components like springs, seals, plates, and housing pieces. The assembly procedure reverses the disassembly with 23 steps like installing seals, springs, pistons and housing components. Special tools are listed and safety notices are provided regarding spring forces and component alignment.
Caterpillar cat 336 e lh excavator (prefix gny) service repair manual (gny000...fjskekdmjekm
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...fjskekmdm
The document provides instructions for assembling a travel motor used in excavators. It describes 27 steps to assemble components like seals, springs, pistons, and plates into the motor housing. Key steps include lubricating mating surfaces, installing retaining rings, and tightening bolts to specified torques. The assembly ends by installing the motor housing cover and bolts, and noting the motor is then ready for installation in the excavator.
Caterpillar cat 336 f l excavator (prefix zbj) service repair manual (zbj0000...fjsjekdmmeme
This document provides instructions for servicing the travel motor on Caterpillar 336F L and 336F LN excavators. It describes the disassembly and assembly procedures, which include 27 individual steps. The document lists required tools and includes illustrations to clarify each step. The summary is:
1. The document provides a service repair manual for Caterpillar 336F L and 336F LN excavators, outlining the process for travel motor disassembly and assembly in 27 steps.
2. Illustrations and lists of required tools accompany the step-by-step instructions.
3. Reassembly requires applying sealant and torquing bolts to the specified values.
Caterpillar cat 336 f l excavator (prefix ljy) service repair manual (ljy0000...fjkskedmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 336 f l excavator (prefix ssn) service repair manual (ssn0000...fjsjekdmmeme
This document provides disassembly and assembly instructions for a 336F L excavator travel motor. The disassembly process involves removing 30 components from the travel motor in a specific sequence. Safety precautions are outlined due to parts under spring tension. The assembly section describes installing 35 components back into the travel motor housing following the reverse of the disassembly order. Tools required are listed for both procedures.
Caterpillar cat 336 f l excavator (prefix dkf) service repair manual (dkf0000...fjsjekdmmeme
This document provides instructions for disassembling and assembling a travel motor for 336F L and 336F LN excavators powered by a C9.3 engine. The disassembly procedure involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly procedure instructs assembling the travel motor in the reverse order and notes to lubricate parts and install components in their original positions and orientations. Safety precautions are provided throughout regarding releasing spring forces and installing spring loaded parts.
The document provides instructions for removing and installing various components on a 336 excavator, including the cab, window wiper motor, and connecting the upper frame and undercarriage frame. It includes lists of required tools and sequential steps supported by illustrations. Safety procedures and torque specifications are noted.
Caterpillar cat 336 f l excavator (prefix wtz) service repair manual (wtz0000...fjsjekdmmeme
This document provides the disassembly and assembly procedures for a travel motor on a 336F excavator model. The disassembly procedure involves 30 steps to remove components like springs, seals, plates, and housing pieces. The assembly procedure reverses the disassembly with 23 steps like installing seals, springs, pistons and housing components. Special tools are listed and safety notices are provided regarding spring forces and component alignment.
Caterpillar cat 336 e lh excavator (prefix gny) service repair manual (gny000...fjskekdmjekm
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...fjskekmdm
The document provides instructions for assembling a travel motor used in excavators. It describes 27 steps to assemble components like seals, springs, pistons, and plates into the motor housing. Key steps include lubricating mating surfaces, installing retaining rings, and tightening bolts to specified torques. The assembly ends by installing the motor housing cover and bolts, and noting the motor is then ready for installation in the excavator.
Caterpillar cat 336 f l excavator (prefix zbj) service repair manual (zbj0000...didkkmmdm
This document provides instructions for assembling and disassembling a travel motor on Caterpillar 336F L and 336F LN excavators powered by a C9.3 engine. It describes the required tools and parts, and provides a step-by-step process with illustrations for removing and installing the final drive, travel motor, and various components like seals, springs, and plates. The summary focuses on the high-level process and does not include part numbers or other specific details.
Caterpillar cat 336 f l excavator (prefix zbj) service repair manual (zbj0000...fhhjsjekmdme
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...shibi1322
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar cat 336 f ln excavator (prefix zbj) service repair manual (zbj000...fjsjekkdmnem
This document provides instructions for assembling and disassembling a travel motor on Caterpillar 336F L and 336F LN excavators powered by a C9.3 engine. It describes the required tools and parts, and provides a step-by-step process with illustrations for removing and installing the final drive, travel motor, and various components like seals, springs, and plates. The summary focuses on the high-level process and does not include part numbers or other specific details.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...fucheng89
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...8foskkdjdkdm3e
This document provides instructions for assembling and disassembling a travel motor on Caterpillar 336F L and 336F LN excavators powered by a C9.3 engine. It describes the required tools and parts, and provides a step-by-step process with illustrations for removing and installing the final drive, travel motor, and various components like seals, springs, and plates. The summary focuses on the high-level process and does not include part numbers or other specific details.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...jiazhi27185
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar cat 336 f l excavator (prefix zbj) service repair manual (zbj0000...fjsjekkdmnem
This document provides instructions for assembling and disassembling a travel motor on Caterpillar 336F L and 336F LN excavators powered by a C9.3 engine. It describes the required tools and parts, and provides a step-by-step process with illustrations for removing and installing the final drive, travel motor, and various components like seals, springs, and plates. The summary focuses on the high-level process and does not include part numbers or other specific details.
Caterpillar cat 336 f ln excavator (prefix zbj) service repair manual (zbj000...fhhjsjekmdme
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar Cat 336F L Excavator (Prefix ZBJ) Service Repair Manual (ZBJ00001...fjdkksmemd
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar cat 336 f ln excavator (prefix zbj) service repair manual (zbj000...didkkmmdm
This document provides instructions for assembling and disassembling a travel motor on Caterpillar 336F L and 336F LN excavators powered by a C9.3 engine. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. Removal instructions are also provided in 13 steps, including draining fluids and marking components for proper reinstallation.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...yin9niaojiao
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
This document provides assembly and disassembly instructions for repairing the travel motor on Caterpillar 336F L and 336F LN excavators. It includes a list of required tools and multi-step procedures with illustrations for tasks like installing seals and bearings, lubricating parts, and torquing bolts. The final section describes removing the final drive and travel motor as the starting point for disassembly.
Caterpillar Cat 336F L Excavator (Prefix ZBJ) Service Repair Manual (ZBJ00001...zatao0179249295
This document provides instructions for assembling and disassembling the travel motor on Caterpillar 336F L and 336F LN excavators. It includes 27 steps for travel motor assembly involving installation of seals, springs, pistons and other components. For removal, it outlines 13 steps including draining fluid, disconnecting hoses, and removing bolts to separate the final drive, travel motor and coupling. Tools required are listed for both assembly and removal procedures.
This document provides assembly and disassembly instructions for repairing the travel motor on Caterpillar 336F L and 336F LN excavators. It includes a list of required tools and multi-step procedures with illustrations for tasks like installing seals and bearings, lubricating parts, and torquing bolts. The final section describes removing the final drive and travel motor as the starting point for disassembly.
Caterpillar Cat 336F L Excavator (Prefix ZBJ) Service Repair Manual (ZBJ00001...luanxianshi27
This document provides assembly and disassembly instructions for repairing the travel motor on Caterpillar 336F L and 336F LN excavators. It includes a list of required tools and multi-step procedures with illustrations for tasks like installing seals and bearings, lubricating parts, and torquing bolts. The final section describes removing the final drive and travel motor as the starting point for disassembly.
Caterpillar Cat 336F L Excavator (Prefix ZBJ) Service Repair Manual (ZBJ00001...wfu089267
This document provides assembly and disassembly instructions for repairing the travel motor on Caterpillar 336F L and 336F LN excavators. It includes a list of required tools and multi-step procedures with illustrations for tasks like installing seals and bearings, lubricating parts, and torquing bolts. The final section describes removing the final drive and travel motor as the starting point for disassembly.
This document provides instructions for assembling and disassembling the travel motor on Caterpillar 336F L and 336F LN excavators. It includes 27 steps for travel motor assembly and 13 steps for removal of the final drive and travel motor. Tools required are listed in tables. Safety precautions are provided to prevent injury from hydraulic pressure.
Caterpillar cat 336 f ln excavator (prefix dkf) service repair manual (dkf000...fjsjekdmmeme
This document provides instructions for disassembling and assembling a travel motor for 336F L and 336F LN excavators powered by a C9.3 engine. The disassembly procedure involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly procedure instructs assembling the travel motor in the reverse order and notes to lubricate parts and install components in their original positions and orientations. Safety precautions are provided throughout regarding releasing spring forces and installing spring loaded parts.
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar cat 330 l excavator (prefix 5ym) service repair manual (5ym00001 ...fjsjekdmmeme
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
More Related Content
Similar to Caterpillar cat 336 f ln excavator (prefix zbj) service repair manual (zbj00001 and up)
Caterpillar cat 336 f l excavator (prefix zbj) service repair manual (zbj0000...didkkmmdm
This document provides instructions for assembling and disassembling a travel motor on Caterpillar 336F L and 336F LN excavators powered by a C9.3 engine. It describes the required tools and parts, and provides a step-by-step process with illustrations for removing and installing the final drive, travel motor, and various components like seals, springs, and plates. The summary focuses on the high-level process and does not include part numbers or other specific details.
Caterpillar cat 336 f l excavator (prefix zbj) service repair manual (zbj0000...fhhjsjekmdme
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...shibi1322
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar cat 336 f ln excavator (prefix zbj) service repair manual (zbj000...fjsjekkdmnem
This document provides instructions for assembling and disassembling a travel motor on Caterpillar 336F L and 336F LN excavators powered by a C9.3 engine. It describes the required tools and parts, and provides a step-by-step process with illustrations for removing and installing the final drive, travel motor, and various components like seals, springs, and plates. The summary focuses on the high-level process and does not include part numbers or other specific details.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...fucheng89
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...8foskkdjdkdm3e
This document provides instructions for assembling and disassembling a travel motor on Caterpillar 336F L and 336F LN excavators powered by a C9.3 engine. It describes the required tools and parts, and provides a step-by-step process with illustrations for removing and installing the final drive, travel motor, and various components like seals, springs, and plates. The summary focuses on the high-level process and does not include part numbers or other specific details.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...jiazhi27185
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar cat 336 f l excavator (prefix zbj) service repair manual (zbj0000...fjsjekkdmnem
This document provides instructions for assembling and disassembling a travel motor on Caterpillar 336F L and 336F LN excavators powered by a C9.3 engine. It describes the required tools and parts, and provides a step-by-step process with illustrations for removing and installing the final drive, travel motor, and various components like seals, springs, and plates. The summary focuses on the high-level process and does not include part numbers or other specific details.
Caterpillar cat 336 f ln excavator (prefix zbj) service repair manual (zbj000...fhhjsjekmdme
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar Cat 336F L Excavator (Prefix ZBJ) Service Repair Manual (ZBJ00001...fjdkksmemd
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar cat 336 f ln excavator (prefix zbj) service repair manual (zbj000...didkkmmdm
This document provides instructions for assembling and disassembling a travel motor on Caterpillar 336F L and 336F LN excavators powered by a C9.3 engine. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. Removal instructions are also provided in 13 steps, including draining fluids and marking components for proper reinstallation.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...yin9niaojiao
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
This document provides assembly and disassembly instructions for repairing the travel motor on Caterpillar 336F L and 336F LN excavators. It includes a list of required tools and multi-step procedures with illustrations for tasks like installing seals and bearings, lubricating parts, and torquing bolts. The final section describes removing the final drive and travel motor as the starting point for disassembly.
Caterpillar Cat 336F L Excavator (Prefix ZBJ) Service Repair Manual (ZBJ00001...zatao0179249295
This document provides instructions for assembling and disassembling the travel motor on Caterpillar 336F L and 336F LN excavators. It includes 27 steps for travel motor assembly involving installation of seals, springs, pistons and other components. For removal, it outlines 13 steps including draining fluid, disconnecting hoses, and removing bolts to separate the final drive, travel motor and coupling. Tools required are listed for both assembly and removal procedures.
This document provides assembly and disassembly instructions for repairing the travel motor on Caterpillar 336F L and 336F LN excavators. It includes a list of required tools and multi-step procedures with illustrations for tasks like installing seals and bearings, lubricating parts, and torquing bolts. The final section describes removing the final drive and travel motor as the starting point for disassembly.
Caterpillar Cat 336F L Excavator (Prefix ZBJ) Service Repair Manual (ZBJ00001...luanxianshi27
This document provides assembly and disassembly instructions for repairing the travel motor on Caterpillar 336F L and 336F LN excavators. It includes a list of required tools and multi-step procedures with illustrations for tasks like installing seals and bearings, lubricating parts, and torquing bolts. The final section describes removing the final drive and travel motor as the starting point for disassembly.
Caterpillar Cat 336F L Excavator (Prefix ZBJ) Service Repair Manual (ZBJ00001...wfu089267
This document provides assembly and disassembly instructions for repairing the travel motor on Caterpillar 336F L and 336F LN excavators. It includes a list of required tools and multi-step procedures with illustrations for tasks like installing seals and bearings, lubricating parts, and torquing bolts. The final section describes removing the final drive and travel motor as the starting point for disassembly.
This document provides instructions for assembling and disassembling the travel motor on Caterpillar 336F L and 336F LN excavators. It includes 27 steps for travel motor assembly and 13 steps for removal of the final drive and travel motor. Tools required are listed in tables. Safety precautions are provided to prevent injury from hydraulic pressure.
Caterpillar cat 336 f ln excavator (prefix dkf) service repair manual (dkf000...fjsjekdmmeme
This document provides instructions for disassembling and assembling a travel motor for 336F L and 336F LN excavators powered by a C9.3 engine. The disassembly procedure involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly procedure instructs assembling the travel motor in the reverse order and notes to lubricate parts and install components in their original positions and orientations. Safety precautions are provided throughout regarding releasing spring forces and installing spring loaded parts.
Similar to Caterpillar cat 336 f ln excavator (prefix zbj) service repair manual (zbj00001 and up) (20)
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar cat 330 l excavator (prefix 5ym) service repair manual (5ym00001 ...fjsjekdmmeme
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Removing the fuel injection lines, exhaust manifold, and rocker shaft/pushrods before removing the cylinder head.
2. Removing the water pump elbow, inlet manifold, and air inlet pipe to access the cylinder head bolts.
3. Using a lifting device to safely remove the 95 kg cylinder head from the engine block.
4. Cleaning all parts to prevent contamination before reinstallation.
Caterpillar cat 330 c fm excavator (prefix b4n) service repair manual (b4n000...fjsjekdmmeme
This document provides instructions for servicing components of a Caterpillar 330C FM Excavator engine, including:
- Installing the cylinder head, which involves positioning a new gasket, attaching lifting tools to the head, applying anti-seize compound, and tightening bolts in a specific sequence.
- Removing and installing the camshaft, which requires removing other parts first like the rocker arm and front cover, then using hooks to position lifters and removing/installing the camshaft.
- Removing and installing the camshaft gear by first removing the camshaft, pressing it off the gear, heating the gear, and pressing it back onto the camshaft
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 b ln excavator (prefix 5lr) service repair manual (5lr000...fjsjekdmmeme
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the component locations and assembly sequences.
Caterpillar cat 330 b ln excavator (prefix 3yr) service repair manual (3yr000...fjsjekdmmeme
The document provides instructions for servicing components of a 330B L excavator including:
1. Installing a compression brake on the engine and connecting wires.
2. Removing and assembling the rocker shaft and pushrods, including disassembling the rocker shaft into individual components.
3. Removing the cylinder head from the engine which involves removing manifold, pushrods, and bolts holding the head in place. Proper lifting equipment is needed due to the head's weight.
Caterpillar cat 330 b l excavator (prefix 6dr) service repair manual (6dr0000...fjsjekdmmeme
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar cat 330 b l excavator (prefix 5lr) service repair manual (5lr0000...fjsjekdmmeme
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the components and steps in the process.
Caterpillar cat 330 b l excavator (prefix 3yr) service repair manual (3yr0000...fjsjekdmmeme
The document provides instructions for servicing components of a 330B L excavator including:
1. Installing a compression brake on the engine and connecting wires.
2. Removing and assembling the rocker shaft and pushrods, including disassembling the rocker shaft into individual components.
3. Removing the cylinder head from the engine which involves removing manifold, pushrods, bolts, and using a lifting device due to the head's weight of 95 kg.
Caterpillar cat 318 b n excavator (prefix 7kz) service repair manual (7kz0000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar cat 318 b ln excavator (prefix 7kz) service repair manual (7kz000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and bolts.
- Removing the flywheel housing by loosening bolts while supported by a lifting tool.
- Removing the vibration damper and pulley by loosening bolts and nuts using sockets and pullers.
Caterpillar cat 318 b l excavator (prefix 7kz) service repair manual (7kz0000...fjsjekdmmeme
The document provides instructions for removing and installing various engine components on a Caterpillar 3046 engine, including:
- Removing the flywheel by drilling holes in it and using a lifting strap and tool.
- Installing a new crankshaft rear seal using sealing tools and installing the flywheel back on with bolts.
- Removing the flywheel housing by removing bolts with a lifting strap and tool, and installing a new gasket and housing.
- Removing the vibration damper and pulley by removing bolts and nuts with sockets and a puller tool if needed.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjsjekdmmeme
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves using various tools to remove over 30 individual components from the final drive housing. The assembly process reverses the disassembly steps and provides details on installing bearings, seals, gears, and other components back into the housing using presses, lifting devices, and installation tools. Precise measurements are taken to determine the correct shim thickness for preloading the bearings. Cleanliness and lubrication of parts is emphasized throughout.
Caterpillar cat 315 c excavator (prefix cfl) service repair manual (cfl00001 ...fjsjekdmmeme
1) The document provides step-by-step instructions for disassembling and assembling the final drive of a 315C excavator.
2) It details 21 steps for disassembly, including removing gears, shafts, seals, and housing components.
3) The 19 steps for assembly describe installing these same parts in reverse order, with notes on cleaning, lubricating, and using various tools to set proper torque and clearance.
Caterpillar cat 311 c u excavator (prefix pad) service repair manual (pad0000...fjsjekdmmeme
The document provides disassembly instructions for the final drive, travel motor, travel brake valve, and traction control valve of an excavator model 311C. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like gears, plates, pistons, springs, and seals from each assembly. Safety warnings are included to take precautions for released spring forces during disassembly.
Caterpillar cat 311 c u excavator (prefix cke) service repair manual (cke0000...fjsjekdmmeme
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The document describes the required tools and provides a step-by-step procedure for removing the old seals and installing new seals. It also includes instructions for removing and installing the engine oil filter base and engine oil cooler.
Caterpillar cat 311 c excavator (prefix pad) service repair manual (pad00001 ...fjsjekdmmeme
The document provides disassembly instructions for the final drive, travel motor, travel brake valve, and traction control valve of an excavator model 311C. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like gears, plates, pistons, springs, and seals from each assembly. Safety warnings are included to take precautions for released spring forces during disassembly.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjsjekdmmeme
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The document describes the required tools and provides a step-by-step procedure for removing the old seals and installing new seals. It also includes instructions for removing and installing the engine oil filter base and engine oil cooler.
Caterpillar cat 311 b track type excavator (prefix 2ls) service repair manual...fjsjekdmmeme
This document provides instructions for servicing components of a 311B excavator engine, including:
1) Instructions for assembling the rocker shaft, including the components and installation steps.
2) Instructions for installing the rocker shaft and pushrods, including torque specifications.
3) Instructions for removing the cylinder head, including removal steps and safety notices.
Caterpillar cat 16 h na motor grader (prefix 6zj) service repair manual (6zj0...fjsjekdmmeme
This document provides instructions for removing and installing various engine components on a 16H NA Motor Grader with a 3406C engine, including:
1. Timing gears and plate
2. Camshaft
3. Camshaft bearings
4. Connecting rod bearings
5. Crankshaft main bearings
The instructions describe each removal and installation step in detail and include notes about proper procedure, tool usage, torque specifications and checks to perform.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L EXCAVATOR ZBJ
Configuration: 336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
340F Excavator Machine Systems
Media Number -UENR6797-01 Publication Date -01/09/2015 Date Updated -21/12/2016
i07175112
Travel Motor - Assemble
SMCS - 4351-016
S/N - DKF1-UP
S/N - RBC1-UP
S/N - SGH1-UP
S/N - ZBJ1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 � 7 N�m (21 � 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15).
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15).
Note: Bearing race (18) must contact retaining ring (17).
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16).
17. Place the pump housing into Tooling (A).
6/10336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g02107957
18. Use Tooling (C) to install rotating assembly (16) into the housing.
Illustration 15 g00887501
Illustration 16 g02107975
19. The notches in cam plate (20) must align with keys (26). The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
7/10336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8).
24. Install brake piston (8) into the housing so that the cast mark on brake piston (8) is aligned
with the brake supply passage in the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level to
prevent damage to the O-ring seals.
8/10336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6).
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5).
Illustration 22 g00887295
9/10336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 240 � 40 N�m (177 � 30 lb ft).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 17 17:52:56 UTC+0800 2020
10/10336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 E...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L EXCAVATOR ZBJ
Configuration: 336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
340F Excavator Machine Systems
Media Number -UENR6797-01 Publication Date -01/09/2015 Date Updated -21/12/2016
i07191698
Final Drive and Travel Motor - Remove and Install
SMCS - 4050; 4351
S/N - DKF1-UP
S/N - RBC1-UP
S/N - SGH1-UP
S/N - ZBJ1-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
1/6336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change" for the correct
draining and filling procedures.
Illustration 1 g02108761
2. Remove bolts (1) and cover (2).
3. Separate the track.
Illustration 2 g02108762
4. Disconnect hose assemblies (3) ( 4), and (6). Remove fitting (5).
2/6336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g02108781
5. Attach Tooling (A) and a suitable lifting device to final drive and travel motor (7). The
weight of final drive and travel motor (7) is approximately 860 kg (1896 lb). Put a slight
lifting tension on final drive and travel motor (7).
Illustration 4 g02108790
Note: Mark the orientation of the final drive and travel motor assembly for installation
purposes.
6. Remove bolts (8).
3/6336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 5 g02108791
7. Use two bolts (8) to remove final drive and travel motor (7).
8. Carefully remove final drive and travel motor (7).
9. Remove bolts (8) from the frame.
Illustration 6 g02108793
10. Remove bolts (9), counterbalance valve (10), and the O-ring seals.
4/6336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 7 g02108794
11. Attach Tooling (B) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 84 kg (185 lb).
12. Remove four bolts (12) and travel motor (11) from final drive (13).
Illustration 8 g02108914
13. Remove coupling (14).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
5/6336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. C - Loctite C5A Copper Anti-Seize -
1. Before assembly remove all compounds, oil, and dust.
2. Install final drive and travel motor (7) in the reverse order of removal.
a. Tighten bolts (9) to a torque of 80 � 8 N�m (60 � 6 lb ft).
b. Apply Tooling (C) to the threads of bolt (8).
c. Tighten bolts (8) to a torque of 250 � 25 N�m (184 � 18 lb ft) and turn an additional
angle of 45 � 5 degrees. Refer to Service Magazine, M0083843, "An Improved Bolt
Tightening Procedure for the Critical Joints Is Now Used on All Excavators" for more
detail information.
d. Tighten hose assembly (3) to a torque of 160 � 16 N�m (120 � 12 lb ft).
e. Tighten bolts (1) to a torque of 130 � 10 N�m (95 � 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 17 17:53:51 UTC+0800 2020
6/6336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L EXCAVATOR ZBJ
Configuration: 336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
340F Excavator Machine Systems
Media Number -UENR6797-01 Publication Date -01/09/2015 Date Updated -21/12/2016
i03885522
Final Drive - Disassemble
SMCS - 4050-015
S/N - DKF1-UP
S/N - RBC1-UP
S/N - SGH1-UP
S/N - ZBJ1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 154-6183 Forcing Bolts 3
C 138-7576 Link Brackets 3
Start By:
a. Remove the final drive and the travel motor.
1/8336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g02131413
1. Attach Tooling (A) and a suitable lifting device to cover (2). The weight of cover (2) is
approximately 20 kg (45 lb). Remove bolts (1) and cover (2).
Illustration 2 g02131414
2. Remove plate (3) from cover (2).
Illustration 3 g02131415
3. Remove sun gear (4), spacer (5), and planetary gear assembly (6).
2/8336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 4 g02131875
4. Remove retaining ring (7), washer (8), planetary gear (9), roller bearing (11), and washer
(12) from carrier assembly (13).
5. Remove retaining ring (10) and sun gear (14) from carrier assembly (13).
Illustration 5 g02131876
6. Remove spacer (16).
7. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (15). The weight
of planetary gear assembly (15) is approximately 32 kg (70 lb). Remove planetary gear
assembly (15).
3/8336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 6 g02131877
8. Drive spring pin (17) into planetary shaft (18) with a suitable hammer and a suitable punch.
9. Remove planetary shaft (18), washer (20), roller bearing (20), planetary gear (23), and
washer (24) from the carrier assembly (21).
10. Remove spring pin (17) from planetary shaft (18) with a suitable hammer and a suitable
punch.
11. Remove retaining ring (19) and sun gear (25) from carrier assembly (21).
Illustration 7 g02131878
12. Remove spacer (26).
13. Attach Tooling (A) and a suitable lifting device to ring gear (27). The weight of ring gear
(27) is approximately 70 kg (155 lb). Remove bolts (28) and ring gear (27).
4/8336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 8 g02131879
14. Remove O-ring seal (29).
15. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (30). The weight
of planetary gear assembly (30) is approximately 57 kg (125 lb). Remove planetary gear
assembly (30).
Illustration 9 g02131881
16. Drive spring pin (31) into planetary shaft (32) with a suitable hammer and a suitable punch.
17. Remove planetary shaft (32), washer (33), roller bearings (35), planetary gear (36), and
washer (36) from the carrier assembly (34).
18. Remove spring pin (31) from planetary shaft (32) with a suitable hammer and a suitable
punch.
5/8336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 10 g02131882
Illustration 11 g02131885
19. Remove bolts (38). Use Tooling (B) in order to remove gear (39).
Illustration 12 g02131886
20. Remove shims (40).
6/8336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 13 g02131887
21. Attach Tooling (C) and a suitable lifting device to sprocket housing (41). The weight of
sprocket housing (41) is approximately 107 kg (235 lb). Remove sprocket housing (41) and
roller bearing (42).
Illustration 14 g02131888
22. Remove bearing races (43) and Duo-Cone seal (44) from sprocket housing (41).
7/8336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 15 g02132155
23. Remove Duo-Cone seal (45) and roller bearing (47) from motor housing (48). The weight of
motor housing (48) is approximately 91 kg (200 lb).
24. If necessary, remove dowels (46) from motor housing (48).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Jun 17 17:54:47 UTC+0800 2020
8/8336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336F L EXCAVATOR ZBJ
Configuration: 336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
340F Excavator Machine Systems
Media Number -UENR6797-01 Publication Date -01/09/2015 Date Updated -21/12/2016
i05103849
Final Drive - Assemble
SMCS - 4050-016
S/N - DKF1-UP
S/N - RBC1-UP
S/N - SGH1-UP
S/N - ZBJ1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 154-6183 Forcing Bolts 3
C 138-7576 Link Brackets 3
D 5P-3931 Anti-Seize Compound -
E 1U-9895 Crossblock 1
F 6V-2012 Depth Micrometer 1
G 6V-7059 Micrometer () 1
H - Loctite 242 -
J 6V-2055 Grease -
K - Loctite 17430 -
1/12336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. L 8T-9206 Seal Installer 1
Illustration 1 g02132155
1. Apply Tooling (D) to the surface of dowels (46) . Install dowels (46) .
2. Raise the temperature of roller bearing (47) . Install the roller bearing (47) on motor housing
(48) .
3. Install Duo-Cone seal (45) .
Illustration 2 g02131888
4. Lower the temperature of bearing races (43) . Install bearing races (43) in sprocket housing
(41) .
5. Install Duo-Cone seal (44) .
2/12336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 3 g02131887
6. Attach Tooling (C) and a suitable lifting device to sprocket housing (41) . The weight of
sprocket housing (41) is approximately 107 kg (235 lb). Install sprocket housing (41) .
7. Raise the temperature of roller bearing (42) . Install the roller bearing (42) .
Illustration 4 g02135728
3/12336F L & 336F LN Excavators ZBJ00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/6/17https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...