The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, including removing the head, springs, brake piston, rotating assembly, and seals. It then outlines 28 steps for assembly, installing components in reverse order and noting proper torque specifications and lubrication of seals. The proper procedure aims to prevent injury from spring forces and ensure correct alignment of parts.
Caterpillar cat 336 e h excavator (prefix hdw) service repair manual (hdw0000...fjskekdmjekm
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes installing seals, springs, plates, pistons, bearings and other parts back into their proper positions, taking care to align markings and lubricate components. Tools and torque specifications are provided for each step.
Caterpillar cat 336 e lh excavator (prefix rza) service repair manual (rza000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly procedure involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly procedure describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lh excavator (prefix ssl) service repair manual (ssl000...fjskekdmjekm
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor and final drive unit. The disassembly process involves removing components like the cover, sun gear, planetary gear assembly, and retaining rings. Precautions are provided regarding weight of components. The assembly process specifies applying thread locking compound and tightening bolts to the specified torques.
Caterpillar cat 336 e l excavator (prefix yce) service repair manual (yce0000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove components like the motor head, springs, brake piston, rotating assembly, and seals. The assembly procedure describes 28 steps and requires various tools to reinstall the components in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Precautions are provided to watch for spring forces and avoid damaging mating surfaces.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjskekmdm
The document provides disassembly and assembly instructions for a 336E and 336E L excavator travel motor. It lists required tools and parts and outlines 27 steps to disassemble the travel motor, removing components like the head, springs, brake piston, and seals. It then describes 21 steps for reassembling the travel motor, providing notes on lubrication and proper positioning of parts like the piston assemblies, cam plate, and brake piston.
Caterpillar cat 336 e lh excavator (prefix hdw) service repair manual (hdw000...cdsasw
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes installing seals, springs, plates, pistons, bearings and other parts back into their proper positions, taking care to align markings and lubricate components. Tools and torque specifications are provided for each step.
Caterpillar Cat 336E H Excavator (Prefix HDW) Service Repair Manual (HDW00001...udfjjdjkkmds
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes lubricating parts and ensuring proper alignment of components. Special safety notes are included throughout to warn of spring loads and to wear protective equipment when specified.
Caterpillar cat 336 e lh excavator (prefix hdw) service repair manual (hdw000...cdfxssw
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It lists 27 steps for disassembly, including removing the head, ports, seals, springs, brake piston, plates, and seals from various components. It then lists 18 steps for assembly, installing components in reverse order and noting proper positioning and torque specifications. Tools required include adapters, nuts, washers, eyebolts, retaining ring pliers, drivers, pullers, and thread rods.
Caterpillar cat 336 e h excavator (prefix hdw) service repair manual (hdw0000...fjskekdmjekm
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes installing seals, springs, plates, pistons, bearings and other parts back into their proper positions, taking care to align markings and lubricate components. Tools and torque specifications are provided for each step.
Caterpillar cat 336 e lh excavator (prefix rza) service repair manual (rza000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly procedure involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly procedure describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lh excavator (prefix ssl) service repair manual (ssl000...fjskekdmjekm
The document provides instructions for disassembling and assembling components of a 336E excavator final drive and travel motor. It describes in detail how to remove and install the travel motor and final drive unit. The disassembly process involves removing components like the cover, sun gear, planetary gear assembly, and retaining rings. Precautions are provided regarding weight of components. The assembly process specifies applying thread locking compound and tightening bolts to the specified torques.
Caterpillar cat 336 e l excavator (prefix yce) service repair manual (yce0000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove components like the motor head, springs, brake piston, rotating assembly, and seals. The assembly procedure describes 28 steps and requires various tools to reinstall the components in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Precautions are provided to watch for spring forces and avoid damaging mating surfaces.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjskekmdm
The document provides disassembly and assembly instructions for a 336E and 336E L excavator travel motor. It lists required tools and parts and outlines 27 steps to disassemble the travel motor, removing components like the head, springs, brake piston, and seals. It then describes 21 steps for reassembling the travel motor, providing notes on lubrication and proper positioning of parts like the piston assemblies, cam plate, and brake piston.
Caterpillar cat 336 e lh excavator (prefix hdw) service repair manual (hdw000...cdsasw
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes installing seals, springs, plates, pistons, bearings and other parts back into their proper positions, taking care to align markings and lubricate components. Tools and torque specifications are provided for each step.
Caterpillar Cat 336E H Excavator (Prefix HDW) Service Repair Manual (HDW00001...udfjjdjkkmds
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes lubricating parts and ensuring proper alignment of components. Special safety notes are included throughout to warn of spring loads and to wear protective equipment when specified.
Caterpillar cat 336 e lh excavator (prefix hdw) service repair manual (hdw000...cdfxssw
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It lists 27 steps for disassembly, including removing the head, ports, seals, springs, brake piston, plates, and seals from various components. It then lists 18 steps for assembly, installing components in reverse order and noting proper positioning and torque specifications. Tools required include adapters, nuts, washers, eyebolts, retaining ring pliers, drivers, pullers, and thread rods.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 8001 and up)fjskekdmjekm
This document provides specifications and layout diagrams for a wheel loader. It includes:
1. Specifications such as operating weight, tipping load, engine details, and dimensions.
2. Layout diagrams showing the location of major components such as the bucket, lights, engine, radiator, exhaust filter, and hydraulic components.
3. Details of electrical component locations in and around the cab, including switches, controllers, and sensors.
The document provides technical information on the configuration and specifications of a wheel loader to support maintenance and repair work. Diagrams identify key parts and their locations on the machine.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 85Z7. It provides instructions on operating and maintaining the machine safely and properly. The manual covers safety procedures, component identification, controls and displays, operating instructions, maintenance, and specifications. Operators should read the full manual before operating the machine to learn how to use it correctly and avoid injuries or damage.
Kawasaki 85 z7 wheel loader equipment components parts catalogue manualfjskekdmjekm
This document is a parts catalog for a wheel loader model 85Z7 powered by an ISUZU 6HK1 engine. It contains a list of parts for the pump system with corresponding part names, numbers, quantities and service codes. The parts include pumps, valves, motors, cylinders and other transmission components. Serial numbers are provided to identify applicable models for each part.
This document is a parts catalog for a Wheel Loader model 80Z7B powered by a Cummins QSB6.7 engine. It contains over 500 numbered parts listings organized by system, including the engine, transmission, hydraulics, electrical, and attachments. It also includes name plates and provides the chassis number range and manufacturer's serial number for the 80Z7B model.
Kawasaki 80 z7 wheel loader parts catalogue manual (serial no. 80c6 5001 and up)fjskekdmjekm
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It contains over 400 parts listed by category including the engine, power train, chassis, cab, electric system, hydraulic system, loader attachment, tools, and name plates. Each part lists the applicable model, mark, and serial number it is associated with.
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It lists various components of the loader in detail including valves, pumps, motors, transmissions, cylinders, accumulators, axles and more. Each component lists the applicable part number, name, quantity, and other identifying information. The parts catalog provides essential information on replacement parts for maintenance and repair of the 80Z7 wheel loader.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 70Z7. It provides safety instructions and information on operating and maintaining the machine. Key points include:
- Read the manual carefully before operating the machine to learn how to safely operate and service it.
- The machine is designed to operate in temperatures from -20°C to 40°C and altitudes up to 2,000 m.
- Only use diesel fuel specified in JIS K-2204, EN-590 or ASTM D-975 standards with 15 ppm or less sulfur content.
- The manual covers safety labels, components, starting and operating the engine, moving and operating the machine,
Cummins qsl9 engine parts catalogue manualfjskekdmjekm
The document is a parts catalog for a Cummins QSL9 engine with serial numbers 73638149- listing various engine parts and specifications. It contains over 170 pages detailing individual engine components and systems through listings of part names, numbers, quantities and other specifications. Key sections include listings for the cylinder block, crankshaft, front gear housing, cam shaft, injectors, turbocharger, cylinder head and other major engine parts and assemblies.
Caterpillar cat 318 e l excavator (prefix dzf) service repair manual (dzf0000...fjskekdmjekm
The document provides instructions for removing and installing a crankshaft timing ring on a C4.4 engine. It describes:
1) Removing the crankshaft first according to a separate procedure.
2) Cleaning the crankshaft timing ring and inspecting it for wear or damage, replacing if needed.
3) Lubricating and installing the timing ring on the crankshaft, ensuring it is seated properly.
Caterpillar cat 318 d2 l excavator (prefix xgs) service repair manual (xgs000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar cat 318 d2 l excavator (prefix xah) service repair manual (xah000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. Precise alignment of parts is critical for correct function of the travel motor.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar cat 318 d2 l excavator (prefix sgb) service repair manual (sgb000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d2 l excavator (prefix dpj) service repair manual (dpj000...fjskekdmjekm
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and housing pieces. Proper cleaning and safety precautions are noted throughout. The goal is to fully separate all parts of the final drive for maintenance or repair.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d l excavator (prefix zkj) service repair manual (zkj0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D L excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive cover, carrier assembly, ring gears, and other components. It then lists 13 steps for assembly, including installing bearings in the main housing, preloading the bearings to determine the correct shim thickness, installing seals and gears, and reassembling disassembled components. The goal is to disassemble and clean all parts before precise reassembly in the reverse order of disassembly.
Caterpillar cat 318 c ln excavator (prefix mdy) service repair manual (mdy000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing components like the cover, carrier assembly, ring gears, and seals. It then lists 4 notes about cleanliness and applying lubricants before presenting 29 steps for assembly, reversing the disassembly process and adding components like bearings and seals.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 8001 and up)fjskekdmjekm
This document provides specifications and layout diagrams for a wheel loader. It includes:
1. Specifications such as operating weight, tipping load, engine details, and dimensions.
2. Layout diagrams showing the location of major components such as the bucket, lights, engine, radiator, exhaust filter, and hydraulic components.
3. Details of electrical component locations in and around the cab, including switches, controllers, and sensors.
The document provides technical information on the configuration and specifications of a wheel loader to support maintenance and repair work. Diagrams identify key parts and their locations on the machine.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 85Z7. It provides instructions on operating and maintaining the machine safely and properly. The manual covers safety procedures, component identification, controls and displays, operating instructions, maintenance, and specifications. Operators should read the full manual before operating the machine to learn how to use it correctly and avoid injuries or damage.
Kawasaki 85 z7 wheel loader equipment components parts catalogue manualfjskekdmjekm
This document is a parts catalog for a wheel loader model 85Z7 powered by an ISUZU 6HK1 engine. It contains a list of parts for the pump system with corresponding part names, numbers, quantities and service codes. The parts include pumps, valves, motors, cylinders and other transmission components. Serial numbers are provided to identify applicable models for each part.
This document is a parts catalog for a Wheel Loader model 80Z7B powered by a Cummins QSB6.7 engine. It contains over 500 numbered parts listings organized by system, including the engine, transmission, hydraulics, electrical, and attachments. It also includes name plates and provides the chassis number range and manufacturer's serial number for the 80Z7B model.
Kawasaki 80 z7 wheel loader parts catalogue manual (serial no. 80c6 5001 and up)fjskekdmjekm
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It contains over 400 parts listed by category including the engine, power train, chassis, cab, electric system, hydraulic system, loader attachment, tools, and name plates. Each part lists the applicable model, mark, and serial number it is associated with.
This document is a parts catalog for a wheel loader model 80Z7 powered by a Cummins QSB6.7 engine. It lists various components of the loader in detail including valves, pumps, motors, transmissions, cylinders, accumulators, axles and more. Each component lists the applicable part number, name, quantity, and other identifying information. The parts catalog provides essential information on replacement parts for maintenance and repair of the 80Z7 wheel loader.
This document is an operation and maintenance manual for a Kawasaki wheel loader model 70Z7. It provides safety instructions and information on operating and maintaining the machine. Key points include:
- Read the manual carefully before operating the machine to learn how to safely operate and service it.
- The machine is designed to operate in temperatures from -20°C to 40°C and altitudes up to 2,000 m.
- Only use diesel fuel specified in JIS K-2204, EN-590 or ASTM D-975 standards with 15 ppm or less sulfur content.
- The manual covers safety labels, components, starting and operating the engine, moving and operating the machine,
Cummins qsl9 engine parts catalogue manualfjskekdmjekm
The document is a parts catalog for a Cummins QSL9 engine with serial numbers 73638149- listing various engine parts and specifications. It contains over 170 pages detailing individual engine components and systems through listings of part names, numbers, quantities and other specifications. Key sections include listings for the cylinder block, crankshaft, front gear housing, cam shaft, injectors, turbocharger, cylinder head and other major engine parts and assemblies.
Caterpillar cat 318 e l excavator (prefix dzf) service repair manual (dzf0000...fjskekdmjekm
The document provides instructions for removing and installing a crankshaft timing ring on a C4.4 engine. It describes:
1) Removing the crankshaft first according to a separate procedure.
2) Cleaning the crankshaft timing ring and inspecting it for wear or damage, replacing if needed.
3) Lubricating and installing the timing ring on the crankshaft, ensuring it is seated properly.
Caterpillar cat 318 d2 l excavator (prefix xgs) service repair manual (xgs000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and describes 33 steps to fully disassemble the final drive components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the hydraulic components, and using lifting devices to remove heavier parts like the carrier assembly, ring gears, and main housing pieces. Safety notices are provided to release pressures and supports heavy parts.
Caterpillar cat 318 d2 l excavator (prefix xah) service repair manual (xah000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor of a 318D2 L excavator. The disassembly process involves removing 27 different components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional warnings to ensure proper installation of components like the cam plate. Precise alignment of parts is critical for correct function of the travel motor.
Caterpillar cat 318 d2 l excavator (prefix wgr) service repair manual (wgr000...fjskekdmjekm
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It describes 33 steps to remove components such as covers, plates, gears, seals, springs, and housings. Safety notices are included to warn of hazards such as parts propelled by springs and pressurized hydraulic fluid. Tools required include lifting devices, brackets, bolts, and pullers. Thorough cleaning is advised before disassembly to prevent dirt entry.
Caterpillar cat 318 d2 l excavator (prefix sgb) service repair manual (sgb000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d2 l excavator (prefix dpj) service repair manual (dpj000...fjskekdmjekm
This document provides instructions to disassemble the final drive on a 318D2 L excavator. It lists the required tools and gives step-by-step directions to remove each component. Key steps include using lifting devices and tools to remove the cover, carrier assembly, ring gears, and housing pieces. Proper cleaning and safety precautions are noted throughout. The goal is to fully separate all parts of the final drive for maintenance or repair.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d l excavator (prefix zkj) service repair manual (zkj0000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D L excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive cover, carrier assembly, ring gears, and other components. It then lists 13 steps for assembly, including installing bearings in the main housing, preloading the bearings to determine the correct shim thickness, installing seals and gears, and reassembling disassembled components. The goal is to disassemble and clean all parts before precise reassembly in the reverse order of disassembly.
Caterpillar cat 318 c ln excavator (prefix mdy) service repair manual (mdy000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing components like the cover, carrier assembly, ring gears, and seals. It then lists 4 notes about cleanliness and applying lubricants before presenting 29 steps for assembly, reversing the disassembly process and adding components like bearings and seals.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E LH EXCAVATOR JEA
Configuration: 336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator Machine Systems
Media Number -UENR0190-01 Publication Date -01/10/2014 Date Updated -04/11/2014
i03863290
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 by 250 mm (10 inch) Threaded Rod 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the travel motor.
1. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
1/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
3. Remove bolts (1).
4. Remove head (2) from the body of the travel motor.
2/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00887302
5. Remove O-ring seal (3), port plate (4), and bearing (5).
Illustration 3 g00887311
6. Remove O-ring seals (6). Remove springs (7).
Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B).
3/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 7. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
8. Remove seal (9) and backup ring (10) from the brake piston.
9. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
10. Remove plates (13) and friction discs (14).
4/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g02107957
Illustration 9 g00887405
Illustration 10 g00887424
11. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
12. Remove Tooling (C) from shaft (15).
13. Remove shaft (15) from rotating assembly (16).
Illustration 11 g00887426
5/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Use Tooling (D) in order to remove retaining ring (17) from shaft (15).
Illustration 12 g00887445
15. Use a suitable press in order to remove bearing race (18) from shaft (15).
Illustration 13 g00887463
16. Rotate shaft (15). Use a suitable press and tooling (E) in order to remove bearing race (19)
from shaft (15).
Illustration 14 g00887501
17. Remove cam plate (20) from barrel assembly (21).
6/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g00887520
18. Remove piston assemblies and retainer plate (22) from barrel assembly (21).
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g00887558
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Remove ball (23) and springs (24).
7/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g02107975
20. Remove bearing (25).
21. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
22. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27).
23. Remove lip seal (28).
Illustration 19 g00887619
24. Remove bolts (29) and cover (30).
8/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g00887729
25. Remove seal (31) and backup ring (32).
Illustration 21 g00887754
26. Remove piston actuator (33) and seal (34).
Illustration 22 g00887762
27. Remove O-ring seal (35) from the housing of the travel motor.
9/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E LH EXCAVATOR JEA
Configuration: 336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator Machine Systems
Media Number -UENR0190-01 Publication Date -01/10/2014 Date Updated -04/11/2014
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15).
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15).
Note: Bearing race (18) must contact retaining ring (17).
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16).
17. Place the pump housing into Tooling (A).
6/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 14 g02107957
18. Use Tooling (C) to install rotating assembly (16) into the housing.
Illustration 15 g00887501
Illustration 16 g02107975
19. The notches in cam plate (20) must align with keys (26). The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
7/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8).
24. Install brake piston (8) into the housing so that the cast mark on brake piston (8) is aligned
with the brake supply passage in the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level to
prevent damage to the O-ring seals.
8/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6).
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5).
Illustration 22 g00887295
9/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 25 23:43:54 UTC+0800 2020
10/10
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED ...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E LH EXCAVATOR JEA
Configuration: 336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator Machine Systems
Media Number -UENR0190-01 Publication Date -01/10/2014 Date Updated -04/11/2014
i07191698
Final Drive and Travel Motor - Remove and Install
SMCS - 4050; 4351
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change" for the correct
draining and filling procedures.
1/5
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g02108761
2. Remove bolts (1) and cover (2).
3. Separate the track.
Illustration 2 g02108762
4. Disconnect hose assemblies (3) ( 4), and (6). Remove fitting (5).
2/5
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 3 g02108781
5. Attach Tooling (A) and a suitable lifting device to final drive and travel motor (7). The
weight of final drive and travel motor (7) is approximately 860 kg (1896 lb). Put a slight
lifting tension on final drive and travel motor (7).
Illustration 4 g02108790
Note: Mark the orientation of the final drive and travel motor assembly for installation
purposes.
6. Remove bolts (8).
Illustration 5 g02108791
7. Use two bolts (8) to remove final drive and travel motor (7).
8. Carefully remove final drive and travel motor (7).
9. Remove bolts (8) from the frame.
3/5
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 6 g02108793
10. Remove bolts (9), counterbalance valve (10), and the O-ring seals.
Illustration 7 g02108794
11. Attach Tooling (B) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 84 kg (185 lb).
12. Remove four bolts (12) and travel motor (11) from final drive (13).
4/5
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Illustration 8 g02108914
13. Remove coupling (14).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
C - Loctite C5A Copper Anti-Seize -
1. Before assembly remove all compounds, oil, and dust.
2. Install final drive and travel motor (7) in the reverse order of removal.
a. Tighten bolts (9) to a torque of 80 ± 8 N·m (60 ± 6 lb ft).
b. Apply Tooling (C) to the threads of bolt (8).
c. Tighten bolts (8) to a torque of 250 ± 25 N·m (184 ± 18 lb ft) and turn an additional
angle of 45 ± 5 degrees. Refer to Service Magazine, M0083843, "An Improved Bolt
Tightening Procedure for the Critical Joints Is Now Used on All Excavators" for more
detail information.
d. Tighten hose assembly (3) to a torque of 160 ± 16 N·m (120 ± 12 lb ft).
e. Tighten bolts (1) to a torque of 130 ± 10 N·m (95 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 25 23:44:50 UTC+0800 2020
5/5
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E LH EXCAVATOR JEA
Configuration: 336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator Machine Systems
Media Number -UENR0190-01 Publication Date -01/10/2014 Date Updated -04/11/2014
i03885522
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 154-6183 Forcing Bolts 3
C 138-7576 Link Brackets 3
Start By:
a. Remove the final drive and the travel motor.
Illustration 1 g02131413
1/8
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 1. Attach Tooling (A) and a suitable lifting device to cover (2). The weight of cover (2) is
approximately 20 kg (45 lb). Remove bolts (1) and cover (2).
Illustration 2 g02131414
2. Remove plate (3) from cover (2).
Illustration 3 g02131415
3. Remove sun gear (4), spacer (5), and planetary gear assembly (6).
2/8
336E H & 336E LH (Hybrid) Excavators JEA00001-UP (MACHINE) POWERED BY...
2020/7/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...