The document provides instructions for assembling a piston motor used in excavator models 336D2 and 336D2 L. It outlines 17 steps for installing various components like bearings, seals, springs, and retaining rings. Safety precautions are provided throughout noting potential injury from parts under spring force. Additional sections provide removal and disassembly instructions for a hydraulic lockout control component.
The document provides instructions for assembling a hydraulic lockout control. It describes 17 steps to assemble a piston motor, including installing bearings, seals, springs, and retaining rings. It also outlines 5 steps to disassemble a hydraulic lockout control, such as removing pins and springs. The assembly process is then described in 6 steps, including installing springs, pins, and lever assemblies. Personal injury warnings are provided throughout.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel using lifting devices, installing O-rings and seals, attaching hoses and fittings, and tightening bolts to specified torques. Proper cleanliness is emphasized to prevent contamination which can cause premature wear.
Caterpillar cat 312 d2 l excavator (prefix whj) service repair manual (whj000...fjjskekdmmse
The document provides instructions for installing a flywheel on a 3054C engine. It describes:
1) Cleaning the flywheel housing and inspecting the crankshaft rear seal for leaks.
2) Heating the ring gear to install it on the flywheel and cleaning the parts after they cool.
3) Using guide bolts and lifting brackets to position the flywheel and install bolts, tightening them to the specified torque.
4) Checking flywheel alignment after installation.
Bomag bw138 ac single tandem vibratory roller service repair manualpfiskdmjekm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 125 ADH, BW 135 AD, BW 138 AD, BW 138 AC. It includes technical specifications, safety information, descriptions of controls, operating procedures, maintenance schedules and procedures, and troubleshooting tips. The document is intended for operators and maintenance personnel and aims to ensure safe and proper use of the machines.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...fksjksmmde
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312D excavator with a C4.2 engine. It describes how to remove the electric starting motor, flywheel, ring gear, and housing bolts. It then explains how to install the housing using a link bracket and driver group, and reinstall the flywheel and starting motor.
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and outlines 30 steps to fully disassemble and reassemble the pump. These include removing housing components, seals, bearings, pistons, springs and other internal parts. Cleanliness is emphasized throughout the process.
Caterpillar cat 336 d excavator (prefix m3m) service repair manual (m3m00001 ...fjskekdmjekm
This document provides installation instructions for installing a swivel on an excavator. It involves attaching lifting tools to the swivel, installing fittings and hoses, and securing the swivel in place with bolts while applying the proper torque. Cleanliness is important during installation to prevent contamination. The document also provides disassembly and assembly instructions for the swivel components.
Caterpillar cat 336 d2 l excavator (prefix tly) service repair manual (tly000...pfiskdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D2 excavator. It details 30 steps for assembly, including installing bearings, seals, pistons, springs and other components in the proper order. Removal instructions are also given for removing the fan motor, bending tabs and removing bolts to access the motor. Safety precautions are provided throughout regarding spring-loaded parts that could cause injury.
The document provides instructions for assembling a hydraulic lockout control. It describes 17 steps to assemble a piston motor, including installing bearings, seals, springs, and retaining rings. It also outlines 5 steps to disassemble a hydraulic lockout control, such as removing pins and springs. The assembly process is then described in 6 steps, including installing springs, pins, and lever assemblies. Personal injury warnings are provided throughout.
Caterpillar cat 336 d2 l excavator (prefix far) service repair manual (far000...pfiskdmjekm
The document provides instructions for assembling and installing a swivel on an excavator. It lists the required tools which include link brackets and vacuum caps. The procedure involves cleaning parts, positioning the swivel using lifting devices, installing O-rings and seals, attaching hoses and fittings, and tightening bolts to specified torques. Proper cleanliness is emphasized to prevent contamination which can cause premature wear.
Caterpillar cat 312 d2 l excavator (prefix whj) service repair manual (whj000...fjjskekdmmse
The document provides instructions for installing a flywheel on a 3054C engine. It describes:
1) Cleaning the flywheel housing and inspecting the crankshaft rear seal for leaks.
2) Heating the ring gear to install it on the flywheel and cleaning the parts after they cool.
3) Using guide bolts and lifting brackets to position the flywheel and install bolts, tightening them to the specified torque.
4) Checking flywheel alignment after installation.
Bomag bw138 ac single tandem vibratory roller service repair manualpfiskdmjekm
This document provides operating and maintenance instructions for BOMAG tandem vibratory rollers, models BW 125 ADH, BW 135 AD, BW 138 AD, BW 138 AC. It includes technical specifications, safety information, descriptions of controls, operating procedures, maintenance schedules and procedures, and troubleshooting tips. The document is intended for operators and maintenance personnel and aims to ensure safe and proper use of the machines.
Caterpillar cat 312 d excavator (prefix kes) service repair manual (kes00001 ...fksjksmmde
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312D excavator with a C4.2 engine. It describes how to remove the electric starting motor, flywheel, ring gear, and housing bolts. It then explains how to install the housing using a link bracket and driver group, and reinstall the flywheel and starting motor.
The document provides instructions for disassembling and assembling a piston pump. It lists the required tools and outlines 30 steps to fully disassemble and reassemble the pump. These include removing housing components, seals, bearings, pistons, springs and other internal parts. Cleanliness is emphasized throughout the process.
Caterpillar cat 336 d excavator (prefix m3m) service repair manual (m3m00001 ...fjskekdmjekm
This document provides installation instructions for installing a swivel on an excavator. It involves attaching lifting tools to the swivel, installing fittings and hoses, and securing the swivel in place with bolts while applying the proper torque. Cleanliness is important during installation to prevent contamination. The document also provides disassembly and assembly instructions for the swivel components.
Caterpillar cat 336 d2 l excavator (prefix tly) service repair manual (tly000...pfiskdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) on a Caterpillar 336D2 excavator. It details 30 steps for assembly, including installing bearings, seals, pistons, springs and other components in the proper order. Removal instructions are also given for removing the fan motor, bending tabs and removing bolts to access the motor. Safety precautions are provided throughout regarding spring-loaded parts that could cause injury.
The document provides instructions for assembling and disassembling various components of an excavator, including:
1. Assembling the piston motor by installing various parts like bearings, seals, springs, and retaining rings in 17 steps.
2. Installing the assembled piston motor and fan motor assembly along with attaching bolts and bending locking tabs.
3. Disassembling the hydraulic lockout control by removing retaining rings, levers, springs, and pins over 5 steps.
4. Reassembling the hydraulic lockout control by reversing the disassembly steps over 6 steps.
5. Installing the assembled hydraulic lockout control along with bolts, screws, and attaching
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...zatao0179249295
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It consists of detailed step-by-step procedures with accompanying illustrations, covering tasks like installing bearings and seals, installing retaining rings, and removing panels and bolts. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...luanxianshi27
The document provides instructions for assembling and installing a hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps to assemble a piston motor, including installing various parts like bearings, seals, springs, and retaining rings. It then explains installing the assembled piston motor and attaching a fan motor assembly. Finally, it outlines installing the hydraulic lockout control unit with bolts, screws, and a cable strap.
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It consists of detailed step-by-step procedures with accompanying illustrations, covering tasks like installing bearings and seals, installing retaining rings, and removing panels and bolts. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
The document provides instructions for assembling and installing a hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps to assemble a piston motor, including installing various parts like bearings, seals, springs, and retaining rings. It then details installing the assembled piston motor and attaching a fan motor assembly. Finally, it explains how to install the hydraulic lockout control unit with bolts and screws, and attaching a switch and cable strap.
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...cnp692569
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps for assembling the piston motor, including installing bearings, seals, springs, and retaining rings. It also describes removing and disassembling the hydraulic lockout control into individual parts and reassembling it. Safety precautions are provided for parts under spring tension.
1) The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) The procedures describe disconnecting hoses and electrical connections, removing mounting bolts and identifying parts to ensure proper reinstallation.
3) Safety notices emphasize the importance of cleanliness and containing fluids to prevent contamination and environmental damage.
The document provides instructions for removing and installing a pump drive on a C18 Industrial Engine. It includes:
1) A list of required tools and safety notices for working on the engine.
2) Step-by-step instructions to disassemble the pump drive by removing components like bolts, gears, and bearings.
3) Parallel steps for reassembling the pump drive, including installing new seals and adjusting end play.
4) Instructions for installing the fully reassembled pump drive back onto the engine.
This service repair manual provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a Caterpillar C11 industrial engine. The procedures describe using various tools to remove and install components in a specific sequence, and include safety notices and illustrations. Removal involves disconnecting hoses, removing retaining components, and extracting parts from the cylinder head or engine. Installation is the reverse of removal.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document includes illustrations to identify the specific components and tools required for each procedure.
The document provides instructions for removing and installing various engine components on a Caterpillar C9.3B industrial engine. It includes steps for removing and installing the crankshaft rear seal, flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, and housing (front). Diagrams and part numbers for required tools are provided for each procedure. The document is part of a service manual for Caterpillar technicians repairing C9.3B engines.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...fjjskmdmem
The document provides instructions for removing and installing wheel spindle assemblies on a Caterpillar 966C wheel loader. Key steps include removing the brake shoes, brake camshaft, and air lines before removing the spindle assembly using a hoist. Installation involves installing seals and bearings on the spider and bearing assembly before placing it on the spindle and securing with nuts. Brake components and air lines are then reinstalled.
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g010...fjjskmdmem
This document provides instructions for removing and installing various components of the 966C wheel loader's power train, including wheels, brake shoes, wheel spindles, the front differential and carrier, and the rear differential and carrier. The procedures involve draining fluids, removing bolts and seals, using hoists and jacks, and reinstalling components in the reverse order while applying lubricants and torques as specified. Safety precautions are noted such as relieving air pressure from brake systems before disconnecting lines.
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...fjjskmdmem
The document provides instructions for removing and installing various components of the rear differential and carrier assembly of a 966C wheel loader, including removing the rear axles, disconnecting air lines, removing mounting bolts and lifting the rear of the machine to access the differential and carrier. The rear differential and carrier unit weighs 350 pounds and houses the internal gears that allow the rear wheels to turn at different speeds.
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j063...fjjskmdmem
This document provides instructions for removing and installing various components of the power train on a 966C wheel loader, including axles, final drive planet carriers, final drive ring gears and hubs, and wheels/bearings. The procedures describe draining oil, removing retaining rings and gears, and reinstalling components along with adjusting wheel bearings and installing seals.
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j000...fjjskmdmem
This document provides instructions for removing and installing various components of the final drive and wheel assembly of a 966C wheel loader, including:
- Removing and installing final drive planet carriers
- Disassembling and assembling final drive planet carriers
- Removing and installing final drive ring gears, hubs, and wheels
- Removing and installing wheels, bearings, and seals
- Removing and installing brake shoes
The document contains detailed step-by-step instructions and diagrams for each procedure.
Caterpillar cat 966 c wheel loader (prefix 18b) service repair manual (18b012...fjjskmdmem
The document provides instructions for disassembling and assembling the fuel injection pump housing of a Caterpillar 966C wheel loader. It describes:
1) Removing components like the fuel rack, lifters, camshaft, and bearings during disassembly.
2) Cleaning and lubricating parts before assembly.
3) Installing bearings, camshaft, lifters, fuel rack, and other components in reverse order of removal.
4) Timing the fuel injection pump housing and governor during installation on the engine.
Caterpillar cat 966 c wheel loader (prefix 18b) service repair manual (18b002...fjjskmdmem
1. The documents provide instructions for removing, installing, and servicing components of the engine oil filter base and cylinder head valves for a Caterpillar 966C wheel loader.
2. The procedures include using various tools to remove and install valves, valve guides, valve seat inserts, and the engine oil filter base.
3. Precautions are provided such as keeping parts clean and containing fluids during repair work.
Caterpillar cat 950 e wheel loader (prefix 65r) service repair manual (65r030...fjjskmdmem
The document provides instructions for removing and installing various components of the front and rear axle assemblies of a Caterpillar 950B wheel loader, including wheel spindles, front and rear axle housings, rear axle housing supports, and the front drive shaft and carrier bearing. The instructions include lists of required tools and parts, diagrams illustrating the component locations and removal/installation steps, and torque specifications for reinstalling components. Safety precautions are noted, such as blocking wheels and releasing parking brakes before removing drive shafts.
Caterpillar cat 950 e wheel loader (prefix 63r) service repair manual (63r060...fjjskmdmem
This document provides instructions for disassembling and assembling the transfer gears of a Caterpillar 950B wheel loader. It describes removing and installing over 30 individual parts in 14 steps. Key steps include using bolts and screws to separate the transmission from the transfer gears, removing bearing cages and gears, and checking bearing end play during reassembly. Proper heating and cooling of parts is emphasized during assembly/disassembly. The document also provides brief instructions for connecting and disconnecting the steering frame lock link and removing and installing the loader bucket.
Caterpillar cat 950 e wheel loader (prefix 22z) service repair manual (22z031...fjjskmdmem
This document provides instructions for removing and installing a crankshaft on a Caterpillar 3304B or 3306B engine. It describes using various tools to remove the crankshaft by lifting it straight up after removing connecting rods, caps and bolts. It also details installing new main and connecting rod bearings, checking clearances with plastigage, and reinstalling the crankshaft by lowering it into place and reattaching connecting rods and caps. A second section provides steps for accurately checking bearing clearances using plastic gauge strips.
More Related Content
Similar to Caterpillar cat 336 d2 l excavator (prefix wdc) service repair manual (wdc00001 and up)
The document provides instructions for assembling and disassembling various components of an excavator, including:
1. Assembling the piston motor by installing various parts like bearings, seals, springs, and retaining rings in 17 steps.
2. Installing the assembled piston motor and fan motor assembly along with attaching bolts and bending locking tabs.
3. Disassembling the hydraulic lockout control by removing retaining rings, levers, springs, and pins over 5 steps.
4. Reassembling the hydraulic lockout control by reversing the disassembly steps over 6 steps.
5. Installing the assembled hydraulic lockout control along with bolts, screws, and attaching
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...zatao0179249295
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It consists of detailed step-by-step procedures with accompanying illustrations, covering tasks like installing bearings and seals, installing retaining rings, and removing panels and bolts. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...luanxianshi27
The document provides instructions for assembling and installing a hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps to assemble a piston motor, including installing various parts like bearings, seals, springs, and retaining rings. It then explains installing the assembled piston motor and attaching a fan motor assembly. Finally, it outlines installing the hydraulic lockout control unit with bolts, screws, and a cable strap.
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It consists of detailed step-by-step procedures with accompanying illustrations, covering tasks like installing bearings and seals, installing retaining rings, and removing panels and bolts. Safety warnings are provided throughout to prevent injury from spring-loaded parts.
The document provides instructions for assembling and installing a hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps to assemble a piston motor, including installing various parts like bearings, seals, springs, and retaining rings. It then details installing the assembled piston motor and attaching a fan motor assembly. Finally, it explains how to install the hydraulic lockout control unit with bolts and screws, and attaching a switch and cable strap.
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...cnp692569
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps for assembling the piston motor, including installing bearings, seals, springs, and retaining rings. It also describes removing and disassembling the hydraulic lockout control into individual parts and reassembling it. Safety precautions are provided for parts under spring tension.
Similar to Caterpillar cat 336 d2 l excavator (prefix wdc) service repair manual (wdc00001 and up) (6)
1) The document provides instructions for removing and installing various fuel system components on a C18 Industrial Engine, including the fuel priming pump, fuel filter base, fuel transfer pump, and electronic unit injectors.
2) The procedures describe disconnecting hoses and electrical connections, removing mounting bolts and identifying parts to ensure proper reinstallation.
3) Safety notices emphasize the importance of cleanliness and containing fluids to prevent contamination and environmental damage.
The document provides instructions for removing and installing a pump drive on a C18 Industrial Engine. It includes:
1) A list of required tools and safety notices for working on the engine.
2) Step-by-step instructions to disassemble the pump drive by removing components like bolts, gears, and bearings.
3) Parallel steps for reassembling the pump drive, including installing new seals and adjusting end play.
4) Instructions for installing the fully reassembled pump drive back onto the engine.
This service repair manual provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a Caterpillar C11 industrial engine. The procedures describe using various tools to remove and install components in a specific sequence, and include safety notices and illustrations. Removal involves disconnecting hoses, removing retaining components, and extracting parts from the cylinder head or engine. Installation is the reverse of removal.
This document provides instructions for removing and installing various engine components on a Caterpillar C11 Industrial Engine. It describes procedures for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, the engine oil filter base, and the engine oil cooler. The document includes illustrations to identify the specific components and tools required for each procedure.
The document provides instructions for removing and installing various engine components on a Caterpillar C9.3B industrial engine. It includes steps for removing and installing the crankshaft rear seal, flywheel housing, vibration damper and pulley, crankshaft front seal, front cover, and housing (front). Diagrams and part numbers for required tools are provided for each procedure. The document is part of a service manual for Caterpillar technicians repairing C9.3B engines.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g028...fjjskmdmem
The document provides instructions for removing and installing wheel spindle assemblies on a Caterpillar 966C wheel loader. Key steps include removing the brake shoes, brake camshaft, and air lines before removing the spindle assembly using a hoist. Installation involves installing seals and bearings on the spider and bearing assembly before placing it on the spindle and securing with nuts. Brake components and air lines are then reinstalled.
Caterpillar cat 966 c wheel loader (prefix 78g) service repair manual (78g010...fjjskmdmem
This document provides instructions for removing and installing various components of the 966C wheel loader's power train, including wheels, brake shoes, wheel spindles, the front differential and carrier, and the rear differential and carrier. The procedures involve draining fluids, removing bolts and seals, using hoists and jacks, and reinstalling components in the reverse order while applying lubricants and torques as specified. Safety precautions are noted such as relieving air pressure from brake systems before disconnecting lines.
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j096...fjjskmdmem
The document provides instructions for removing and installing various components of the rear differential and carrier assembly of a 966C wheel loader, including removing the rear axles, disconnecting air lines, removing mounting bolts and lifting the rear of the machine to access the differential and carrier. The rear differential and carrier unit weighs 350 pounds and houses the internal gears that allow the rear wheels to turn at different speeds.
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j063...fjjskmdmem
This document provides instructions for removing and installing various components of the power train on a 966C wheel loader, including axles, final drive planet carriers, final drive ring gears and hubs, and wheels/bearings. The procedures describe draining oil, removing retaining rings and gears, and reinstalling components along with adjusting wheel bearings and installing seals.
Caterpillar cat 966 c wheel loader (prefix 76j) service repair manual (76j000...fjjskmdmem
This document provides instructions for removing and installing various components of the final drive and wheel assembly of a 966C wheel loader, including:
- Removing and installing final drive planet carriers
- Disassembling and assembling final drive planet carriers
- Removing and installing final drive ring gears, hubs, and wheels
- Removing and installing wheels, bearings, and seals
- Removing and installing brake shoes
The document contains detailed step-by-step instructions and diagrams for each procedure.
Caterpillar cat 966 c wheel loader (prefix 18b) service repair manual (18b012...fjjskmdmem
The document provides instructions for disassembling and assembling the fuel injection pump housing of a Caterpillar 966C wheel loader. It describes:
1) Removing components like the fuel rack, lifters, camshaft, and bearings during disassembly.
2) Cleaning and lubricating parts before assembly.
3) Installing bearings, camshaft, lifters, fuel rack, and other components in reverse order of removal.
4) Timing the fuel injection pump housing and governor during installation on the engine.
Caterpillar cat 966 c wheel loader (prefix 18b) service repair manual (18b002...fjjskmdmem
1. The documents provide instructions for removing, installing, and servicing components of the engine oil filter base and cylinder head valves for a Caterpillar 966C wheel loader.
2. The procedures include using various tools to remove and install valves, valve guides, valve seat inserts, and the engine oil filter base.
3. Precautions are provided such as keeping parts clean and containing fluids during repair work.
Caterpillar cat 950 e wheel loader (prefix 65r) service repair manual (65r030...fjjskmdmem
The document provides instructions for removing and installing various components of the front and rear axle assemblies of a Caterpillar 950B wheel loader, including wheel spindles, front and rear axle housings, rear axle housing supports, and the front drive shaft and carrier bearing. The instructions include lists of required tools and parts, diagrams illustrating the component locations and removal/installation steps, and torque specifications for reinstalling components. Safety precautions are noted, such as blocking wheels and releasing parking brakes before removing drive shafts.
Caterpillar cat 950 e wheel loader (prefix 63r) service repair manual (63r060...fjjskmdmem
This document provides instructions for disassembling and assembling the transfer gears of a Caterpillar 950B wheel loader. It describes removing and installing over 30 individual parts in 14 steps. Key steps include using bolts and screws to separate the transmission from the transfer gears, removing bearing cages and gears, and checking bearing end play during reassembly. Proper heating and cooling of parts is emphasized during assembly/disassembly. The document also provides brief instructions for connecting and disconnecting the steering frame lock link and removing and installing the loader bucket.
Caterpillar cat 950 e wheel loader (prefix 22z) service repair manual (22z031...fjjskmdmem
This document provides instructions for removing and installing a crankshaft on a Caterpillar 3304B or 3306B engine. It describes using various tools to remove the crankshaft by lifting it straight up after removing connecting rods, caps and bolts. It also details installing new main and connecting rod bearings, checking clearances with plastigage, and reinstalling the crankshaft by lowering it into place and reattaching connecting rods and caps. A second section provides steps for accurately checking bearing clearances using plastic gauge strips.
Caterpillar cat 950 e wheel loader (prefix 22z) service repair manual (22z000...fjjskmdmem
1. The document provides instructions for disassembling and assembling components of the fuel injection system for Caterpillar 3304B and 3306B engines, including the fuel injection pump housing, governor, and related parts.
2. The procedures include removing and installing bearings, camshafts, lifters, racks, gaskets and covers using various tools. Proper positioning and torque specifications are provided.
3. Detailed illustrations accompany each step to show how to disassemble and assemble the parts in the correct order and orientation.
Caterpillar cat 950 b wheel loader (prefix 65r) service repair manual (65r030...fjjskmdmem
The document provides instructions for removing and installing various components of the front and rear axle assemblies of a Caterpillar 950B wheel loader, including wheel spindles, front and rear axle housings, rear axle housing supports, and the front drive shaft and carrier bearing. The instructions include numbered steps detailing how to properly support and secure the components, which fasteners to remove and install, and proper torques to use.
Caterpillar cat 950 b wheel loader (prefix 65r) service repair manual (65r028...fjjskmdmem
The document provides instructions for removing and installing an exhaust manifold on a Caterpillar 950B wheel loader. Key steps include removing the turbocharger, fuel injection lines, exhaust manifold nuts and bolts, and exhaust manifold gaskets. When installing, apply anti-seize compound to studs if removed previously and ensure the two longer studs are in the correct position. Proper cleaning and installation of all parts is emphasized to prevent contamination.
Caterpillar cat 950 b wheel loader (prefix 65r) service repair manual (65r000...fjjskmdmem
This document provides instructions for removing and installing various components of a Caterpillar 3304 engine, including the spacer plate, water directors, lifter group, camshaft, and camshaft bearings. The procedures provide detailed steps and illustrations for each component, with notices to keep parts clean and properly align timing marks.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415273
Piston Motor (Hydraulic Fan) - Assemble
SMCS - 1386-016-QP; 5058-016-FM; 5058-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-1861 Retaining Ring Pliers 1
C 1P-0510 Driver Gp 1
Illustration 1 g01207288
1. Install bearing cup (29).
1/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g01207286
2. Install lip seal (28).
3. Use Tooling (C) in order to install retaining ring (27).
Illustration 3 g01207624
4. Raise the temperature of bearing cone (26).
5. Install bearing cone (26) onto shaft (25).
Illustration 4 g01207285
6. Install shaft (25) and swashplate (24).
2/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 5 g01207283
Illustration 6 g01207284
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
7. Install shim (21), spring (22), and shim (23).
8. Use Tooling (C) and Tooling (B) in order to install retaining ring (19).
3/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g01207282
9. Install pins (18).
Illustration 8 g01207281
10. Install bearing (17).
11. Install pistons (15) and retainer (16).
Illustration 9 g01207280
12. Install rotating group (14) and shim (13).
4/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 10 g01207279
13. Install bearing cone (12).
Illustration 11 g01207278
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install O-ring seal (11), poppet (10), spring (9), poppet (8), sleeve (7), and plug (6).
5/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 12 g01207276
15. Lower the temperature of bearing cup (5).
16. Install bearing cup (5), port plate (4), and O-ring seal (3).
Illustration 13 g01207275
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
17. Install head (2) and bolts (1).
End By:
a. Install the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Install".
6/7
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02415453
Piston Motor (Hydraulic Fan) - Install
SMCS - 1386-012-QP; 5058-012-FM
installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement.
Illustration 1 g01207418
1. Use a suitable lifting device to install piston motor (5). The weight of piston motor (5) is
approximately 23 kg (50 lb).
2. Install bolts (6).
1/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g01207416
3. Use a suitable lifting device to reposition fan motor assembly (4), as shown. The weight of
fan motor assembly (4) is approximately 68 kg (150 lb).
Illustration 3 g01207415
4. Install hub (3) and bolts (2).
5. Bend locking tabs (1) over bolts (2).
End By:
a. Install the fan. Refer to Disassembly and Assembly, "Fan - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 10 23:59:03 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02554917
Hydraulic Lockout Control - Remove
SMCS - 5001-011-LK
Removal Procedure
Illustration 1 g01187398
1. Remove screws (2) and panel (1).
1/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 2 g01278781
2. Remove screws (6). Cut cable strap (8) and place switch (7) aside.
3. Remove bolt (4), bolt (5), and hydraulic lockout control (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 10 23:59:59 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02378526
Hydraulic Lockout Control - Disassemble
SMCS - 5001-015-LK
Disassembly Procedure
Start By:
a. Remove the hydraulic lockout control. Refer to Disassembly and Assembly, "Hydraulic
Lockout Control - Remove".
Illustration 1 g01187382
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
1/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove retaining rings (1) and lever assembly (2).
2. Remove retaining ring (4), lever assembly (5), and spring (3).
Illustration 2 g01187383
3. Pull back cover (8) in order to remove pin (7) from pipe assembly (6).
Illustration 3 g01187385
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
2/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 4. Remove pin (10) from pin (9).
5. Remove spring (11) from cover (12).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 00:00:55 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02378527
Hydraulic Lockout Control - Assemble
SMCS - 5001-016-LK
Assembly Procedure
Illustration 1 g01187385
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 1. Install spring (11) to cover (12).
2. Install pin (10) to pin (9).
Illustration 2 g01187383
3. Install pin (7) to pipe assembly (6).
4. Slide cover (8) over pipe assembly (6).
Illustration 3 g01187382
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
5. Install spring (3), lever assembly (5), and retaining ring (4).
2/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 6. Install lever assembly (2) and retaining rings (1).
End By:
a. Install the hydraulic lockout control. Refer to Disassembly and Assembly, "Hydraulic
Lockout Control - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 00:01:51 UTC+0800 2020
3/3
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i07426591
Hydraulic Lockout Control - Install
SMCS - 5001-012-LK
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 243 -
Illustration 1 g01278781
1. Install hydraulic lockout control (3), bolt (4), and bolt (5).
2. Apply Tooling (A) to the threads of screws (6). Position switch assembly (7) and install
screws (6). Tighten screws (6) to a torque of 0.7 ± 0.1 N·m (6.2 ± 0.9 lb in). Attach cable
strap (8).
1/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g01187398
3. Install panel (1) and screws (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Aug 11 00:02:47 UTC+0800 2020
2/2
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D2 EXCAVATOR WDC
Configuration: 336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engine
Disassembly and Assembly
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic
Power Unit Machine Systems
Media Number -RENR8648-30 Publication Date -01/03/2015 Date Updated -15/08/2018
i02417256
Operator Console - Remove and Install
SMCS - 5258-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Start By:
a. Remove the seat. Refer to Disassembly and Assembly, "Seat - Remove".
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for
installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this
helps to keep contaminants from entering the system.
1/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g01208165
1. Remove plates (1) and (2).
Illustration 2 g01196137
2. Attach Tooling (A) and an air supply to the hydraulic oil tank. Apply 345 ± 70 kPa
(50 ± 10 psi) to Tooling (A).
2/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 6. Disconnect harness assemblies (6).
Illustration 7 g01208204
7. Remove plate (8). Move floor mat (7) toward the front of the cab.
Illustration 8 g01208208
8. Remove bolts (9) from each side of the operator console. Pull hose assemblies (3) and (4)
through the floor of the cab. Hose assemblies (3) and (4) were removed in Steps 3 and 4.
Pull harness assemblies (5) and (6) through the floor of the cab. Harness assemblies (5) and
(6) were removed in Steps 5 and 6.
Note: If the machine is equipped with a radio, the antenna will need to be disconnected.
4/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 9 g01208250
9. Disconnect harness assembly (10).
Illustration 10 g01208252
10. Remove bolts (11) and operator console (12).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
Illustration 11 g01208252
1. Install operator console (12) and bolts (11).
5/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 12 g01208250
2. Connect harness assembly (10).
Illustration 13 g01208208
3. Insert hose assemblies (3) and (4) through the hole in the cab floor. Insert harness
assemblies (5) and (6) through the holes in the cab floor. Hose assemblies (3) and (4) and
harness assemblies (5) and (6) will be connected in the following steps. Install bolts (9)
from each side of the operator console.
Note: If the machine is equipped with a radio, the antenna will need to be connected.
Illustration 14 g01208204
6/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 4. Move floor mat (7) toward the rear of the cab. Install plate (8).
Illustration 15 g01208202
5. Connect harness assemblies (6).
Illustration 16 g01208198
6. Connect harness assemblies (5).
Illustration 17 g01208191
7. Connect hose assemblies (4).
7/9
336D2 & 336D2 L Excavators WDC00001-UP (MACHINE) POWERED BY C9 Engi...
2020/8/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...