This document provides instructions for disassembling and assembling a final drive for 330F and 330F LN excavators. The disassembly procedure involves using various tools to remove 37 individual parts from the final drive assembly, including gears, shafts, housings, seals and bearings. The assembly procedure consists of 30 steps to reinstall the parts in reverse order, noting the proper application of sealants and adjustment of bearing preload using shims. Precise alignment and cleanliness of parts is emphasized throughout.
Caterpillar cat 330 f excavator (prefix jhf) service repair manual (jhf00001 ...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly, covers, gears, carriers, shafts, and seals. The assembly section provides instructions for installing seals, bearings, gears, carriers, and other components in the reverse order of disassembly. Special tools and precautions are noted throughout to properly set bearing preload and install seals without damage.
Caterpillar cat 330 f ln excavator (prefix jhf) service repair manual (jhf000...fksjksmmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by having the technician remove the final drive assembly and place it on a transmission repair stand. Detailed steps are then provided to disassemble the various components of the final drive including removing gears, shafts, carriers, and housing pieces. The final section provides instructions for reassembling the final drive, making sure to clean all parts and replace any damaged seals. Technicians are instructed to properly set the bearing preload when reinstalling components.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly, cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly section provides instructions for installing seals, bearings, gears, ring gear, and adjusting the bearing preload to complete reassembly of the final drive. Tools required are listed for both disassembly and assembly.
Caterpillar cat 330 f excavator (prefix jhf) service repair manual (jhf00001 ...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar cat 330 f ln excavator (prefix jhf) service repair manual (jhf000...dueikdkmem
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar Cat 330F, 330F L and 330F LN Excavator (Prefix JHF) Service Repai...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
Caterpillar Cat 330F, 330F L and 330F LN Excavator (Prefix JHF) Service Repai...zan2736ban
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, and using shims to set the proper bearing preload when reassembling components. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar Cat 330F L Excavator (Prefix JHF) Service Repair Manual (JHF00001...f8uesjdkdmdm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar cat 330 f excavator (prefix jhf) service repair manual (jhf00001 ...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly, covers, gears, carriers, shafts, and seals. The assembly section provides instructions for installing seals, bearings, gears, carriers, and other components in the reverse order of disassembly. Special tools and precautions are noted throughout to properly set bearing preload and install seals without damage.
Caterpillar cat 330 f ln excavator (prefix jhf) service repair manual (jhf000...fksjksmmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by having the technician remove the final drive assembly and place it on a transmission repair stand. Detailed steps are then provided to disassemble the various components of the final drive including removing gears, shafts, carriers, and housing pieces. The final section provides instructions for reassembling the final drive, making sure to clean all parts and replace any damaged seals. Technicians are instructed to properly set the bearing preload when reinstalling components.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...fjskkksmemm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly, cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly section provides instructions for installing seals, bearings, gears, ring gear, and adjusting the bearing preload to complete reassembly of the final drive. Tools required are listed for both disassembly and assembly.
Caterpillar cat 330 f excavator (prefix jhf) service repair manual (jhf00001 ...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar cat 330 f ln excavator (prefix jhf) service repair manual (jhf000...dueikdkmem
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar Cat 330F, 330F L and 330F LN Excavator (Prefix JHF) Service Repai...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
Caterpillar Cat 330F, 330F L and 330F LN Excavator (Prefix JHF) Service Repai...zan2736ban
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, and using shims to set the proper bearing preload when reassembling components. Precise tools and measurements are required to correctly reassemble the final drive.
Caterpillar Cat 330F L Excavator (Prefix JHF) Service Repair Manual (JHF00001...f8uesjdkdmdm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f excavator (prefix jhf) service repair manual (jhf00001 ...dfjjsjkemmm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...idkkdmmd
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise measurements and torque specifications are provided to ensure correct assembly.
Caterpillar Cat 330F L Excavator (Prefix JHF) Service Repair Manual (JHF00001...f8uejkkdmdm8u
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar Cat 330F L Excavator (Prefix JHF) Service Repair Manual (JHF00001...8ufjsekddm8u
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...dfjjsjkemmm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. The disassembly procedure involves using various tools to remove over 30 individual parts in a specific sequence. The assembly procedure similarly provides step-by-step instructions to reinstall the parts in reverse order, noting the importance of cleaning, applying sealants, and properly setting bearing preloads.
Caterpillar cat 330 f ln excavator (prefix jhf) service repair manual (jhf000...ikdkdmdm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
The document provides instructions for removing and installing various components of an excavator engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, and exhaust manifold. The procedures include required tools, safety warnings, step-by-step instructions, and torque specifications for reinstallation.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to contain hydraulic fluids.
This document provides disassembly instructions for the travel motor on a 336F L XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing the head, springs, relief valves, pistons, barrel assembly, swashplate and other internal components. Detailed illustrations accompany each step to show how to properly remove parts and note their positions for reassembly. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly.
Caterpillar Cat 336F L XE Excavator (Prefix MTW) Service Repair Manual (MTW00...jdksmmdmdd
This document provides disassembly instructions for a travel motor on a 336F LN XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations accompany each step to show how to remove each part in the proper sequence. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly. Required tools are listed that will be needed to complete the process.
Caterpillar Cat 336F L XE Excavator (Prefix YBH) Service Repair Manual (YBH00...jdksmmdmdd
This document provides instructions for disassembling the travel motor on a 336F LNXE excavator. The 27 step procedure includes removing components like the motor head assembly, barrel assembly, piston assemblies, springs, seals, plates and more. Special care must be taken when removing components under spring pressure. Tools and safety precautions are listed for each step. The goal is to disassemble all parts while keeping them organized for proper reassembly.
This document provides instructions to disassemble a travel motor on a 349F and 349F L excavator. It outlines 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, port plate, springs, seals, bearings, valves and more. Precautions are provided to be aware of parts under spring force. Various specialized tools are required to properly support, attach, extract and remove components from the motor.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a hydraulic fan drive for an excavator. It details 22 steps for disassembly, removing components like bolts, retainers, seals, discs, and housing pieces. It then details 14 steps for reassembly, including pressing in bearings and seals, installing retaining rings, and pressing the shaft assembly back into place using the proper tools. Cleanliness is emphasized throughout to prevent contamination of precision components.
Caterpillar Cat 349E L Excavator (Prefix KFX) Service Repair Manual (KFX00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Personal protective equipment is recommended when removing parts with stored spring energy. Tools include lifting devices, bolts, nuts, and specialized pullers and presses. Drained fluids must be contained and disposed of properly.
Caterpillar Cat 349E L Excavator (Prefix MPZ) Service Repair Manual (MPZ00001...jdksmmdmdd
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts.
More Related Content
Similar to Caterpillar Cat 330F Excavator (Prefix JFR) Service Repair Manual (JFR00001 and up).pdf
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f excavator (prefix jhf) service repair manual (jhf00001 ...dfjjsjkemmm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...idkkdmmd
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise measurements and torque specifications are provided to ensure correct assembly.
Caterpillar Cat 330F L Excavator (Prefix JHF) Service Repair Manual (JHF00001...f8uejkkdmdm8u
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar Cat 330F L Excavator (Prefix JHF) Service Repair Manual (JHF00001...8ufjsekddm8u
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins by describing how to disassemble the various components of the final drive by removing gears, shafts, carriers, and housings. It then describes the assembly process, which involves pressing in new bearings, installing seals with specialized tools, adjusting the bearing preload using shims to achieve the proper clearance, and reassembling the components in reverse order. Precise tools and measurements are required to correctly reassemble the final drive.
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...dfjjsjkemmm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. The disassembly procedure involves using various tools to remove over 30 individual parts in a specific sequence. The assembly procedure similarly provides step-by-step instructions to reinstall the parts in reverse order, noting the importance of cleaning, applying sealants, and properly setting bearing preloads.
Caterpillar cat 330 f ln excavator (prefix jhf) service repair manual (jhf000...ikdkdmdm
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then provides assembly steps in reverse order, including pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings using lifting devices due to the heavy weights involved. Precautions are given to clean parts thoroughly and apply specified threadlockers and sealants during reassembly.
Caterpillar cat 330 f l excavator (prefix jhf) service repair manual (jhf0000...fjsjjdkemmde
This document provides instructions for disassembling and assembling the final drive of an excavator model 330F. It begins with disassembly steps including removing the final drive assembly and various gears, shafts, and housings. It then describes assembling the final drive by cleaning parts, pressing in bearings, installing seals, adjusting bearing preload with shims, and reinstalling gears and housings. The summary provides an overview of the key steps and goals of the document.
Similar to Caterpillar Cat 330F Excavator (Prefix JFR) Service Repair Manual (JFR00001 and up).pdf (12)
The document provides instructions for removing and installing various components of an excavator engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, and exhaust manifold. The procedures include required tools, safety warnings, step-by-step instructions, and torque specifications for reinstallation.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to contain hydraulic fluids.
This document provides disassembly instructions for the travel motor on a 336F L XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing the head, springs, relief valves, pistons, barrel assembly, swashplate and other internal components. Detailed illustrations accompany each step to show how to properly remove parts and note their positions for reassembly. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly.
Caterpillar Cat 336F L XE Excavator (Prefix MTW) Service Repair Manual (MTW00...jdksmmdmdd
This document provides disassembly instructions for a travel motor on a 336F LN XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations accompany each step to show how to remove each part in the proper sequence. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly. Required tools are listed that will be needed to complete the process.
Caterpillar Cat 336F L XE Excavator (Prefix YBH) Service Repair Manual (YBH00...jdksmmdmdd
This document provides instructions for disassembling the travel motor on a 336F LNXE excavator. The 27 step procedure includes removing components like the motor head assembly, barrel assembly, piston assemblies, springs, seals, plates and more. Special care must be taken when removing components under spring pressure. Tools and safety precautions are listed for each step. The goal is to disassemble all parts while keeping them organized for proper reassembly.
This document provides instructions to disassemble a travel motor on a 349F and 349F L excavator. It outlines 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, port plate, springs, seals, bearings, valves and more. Precautions are provided to be aware of parts under spring force. Various specialized tools are required to properly support, attach, extract and remove components from the motor.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a hydraulic fan drive for an excavator. It details 22 steps for disassembly, removing components like bolts, retainers, seals, discs, and housing pieces. It then details 14 steps for reassembly, including pressing in bearings and seals, installing retaining rings, and pressing the shaft assembly back into place using the proper tools. Cleanliness is emphasized throughout to prevent contamination of precision components.
Caterpillar Cat 349E L Excavator (Prefix KFX) Service Repair Manual (KFX00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Personal protective equipment is recommended when removing parts with stored spring energy. Tools include lifting devices, bolts, nuts, and specialized pullers and presses. Drained fluids must be contained and disposed of properly.
Caterpillar Cat 349E L Excavator (Prefix MPZ) Service Repair Manual (MPZ00001...jdksmmdmdd
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts.
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Precise torques and specifications are provided to ensure correct reassembly.
Caterpillar Cat 349D2 L Excavator (Prefix RAN) Service Repair Manual (RAN0000...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pistons, and housing. Precautions are provided to keep parts clean and in correct orientation during reassembly.
This document provides instructions for removing and installing the rear gear group on a 349D2 and 349D2 L excavator powered by a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, bushings and bearings. The installation procedure involves 12 steps including lowering temperatures of bearings before installation, applying sealant to bolts, and ensuring proper dimensions are met. Tools including drivers and installer are required.
The document provides instructions for disassembling a travel motor. It lists the required tools and gives step-by-step instructions to remove parts like the head, plates, seals, pins, and more. Safety notices are included to handle parts carefully and avoid contamination when disassembling components.
Caterpillar Cat 349D2 L Excavator (Prefix GAX) Service Repair Manual (GAX0000...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, reinstalling these components in reverse order and noting to clean all parts and replace seals and gaskets. Precautions are provided to contain fluids, mark parts locations, and avoid contaminating the hydraulic system.
The document provides instructions for removing and installing various components of an excavator engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, and exhaust manifold. The procedures include required tools, safety warnings, step-by-step instructions, and torque specifications for reinstallation.
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1. Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Removing the crankshaft rear seal by removing bolts. Detailed steps and illustrations are provided for each procedure. Required tools are listed.
This document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like plates and seals. It then describes removing the head, brake piston, disks, and rotating group. Components like the shaft, bearings, and pistons are then removed from the rotating group. Reassembly involves reversing these steps and ensuring components like O-rings and washers are properly installed. Precautions are provided to prevent contamination and correctly identify parts.
Caterpillar Cat 336D2 L Excavator (Prefix FAJ) Service Repair Manual (FAJ0000...jdksmmdmdd
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools.
This document provides instructions for disassembling the travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 27 steps to remove parts like the motor head assembly, springs, pistons, seals, plates and other components. Various tools are required including bolts, retaining ring pliers, drivers and pullers. Precautions are mentioned to relieve spring pressure safely and contain fluids. The process yields individual parts to allow inspection and replacement of worn items.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR JFR
Configuration: 330F & 330F LN Excavators JFR00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326F, 329F and 330F Excavators Machine Systems
Media Number -UENR3313-07 Publication Date -01/09/2015 Date Updated -12/09/2018
i05436085
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 138-7575 Link Bracket 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G 138-7576 Link Bracket 2
H 154-6181 Forcing Screw 3
Start By:
a. Remove the final drive.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled to the original locations.
1/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00892878
2. Use Tooling (G) and a suitable lifting device to position the final drive assembly onto
Tooling (A). The weight of the final drive assembly is approximately 550 kg (1200 lb).
3. Remove bolts (1).
Illustration 2 g00892883
4. Use Tooling (B) and a suitable lifting device to remove cover (2). The weight of cover (2) is
approximately 32 kg (70 lb).
Illustration 3 g00892888
2/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 5. Remove bolts (3) and gear (4). Check plate (6). Replace plate (6) if plate (6) is worn.
Remove plugs (5) from cover (2).
Illustration 4 g00892906
6. Remove O-ring seals (7) from plugs (5).
Illustration 5 g00892930
7. Remove gear (8) and spacer (9).
Illustration 6 g00892965
3/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 8. Use Tooling (C) to remove retaining ring (10). Remove washer (11) and gear (12). Remove
bearing assembly (13) and washer (14).
9. Repeat Step 8 for the other two gear assemblies.
Illustration 7 g00892968
10. Remove retaining ring (15).
Illustration 8 g00892975
11. Remove carrier assembly (16).
4/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 9 g02408860
12. Use a suitable press to remove the shafts from carrier assembly (16).
Illustration 10 g00892977
13. Remove gear (17) and spacer (18).
Illustration 11 g00892997
5/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. 14. Use Tooling (D) and a suitable lifting device to remove planetary carrier (19). The weight of
planetary carrier (19) is approximately 48 kg (105 lb).
Illustration 12 g00893019
15. Remove retaining ring (21). Lift planetary carrier (19) off sun gear (20).
Illustration 13 g00896860
16. Drive spring pin (23) into planetary shaft (22).
Illustration 14 g00893043
6/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. 17. Remove planetary shaft (22). Use a suitable punch to remove spring pin (23) from planetary
shaft (22).
Illustration 15 g00896863
18. Remove washers (24) and bearing (25) from planetary gear (26).
19. Repeat Steps 16 through 18 for the other two planetary gears.
Illustration 16 g01842853
20. Remove gear (27). Remove spacer (27A).
Illustration 17 g01842974
7/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 21. Use two people to remove carrier assembly (28). The weight of carrier assembly (28) is
approximately 38 kg (85 lb).
Illustration 18 g01843140
22. Drive spring pin (30) into shaft (29).
Illustration 19 g00893658
23. Remove shaft (29). Use a suitable punch to remove spring pin (30) from shaft (29).
Illustration 20 g00893674
24. Remove washers (31) and bearings (32) from planetary gear (33).
8/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. 25. Repeat Steps 22 through 24 for the other three planetary gears.
Illustration 21 g01208300
26. Fasten Tooling (E) and a suitable lifting device to ring gear (34), as shown. Remove ring
gear (34) from sprocket housing (35). The weight of ring gear (34) is approximately 66 kg
(146 lb).
Illustration 22 g01208542
27. Remove O-ring seal (36) from sprocket housing (35).
Illustration 23 g01208553
9/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 28. Remove bolts (37) from coupling gear (38).
Illustration 24 g03431447
29. Install Tooling (H) in coupling gear (38). Tighten the Tooling (H) evenly in order to loosen
coupling gear (38). Remove the coupling gear from the motor housing.
Illustration 25 g01208578
Illustration 26 g01208625
30. Remove shims (40) from the motor housing.
10/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Note: Inner cones and outer bearing cones (42) and (44) are a slip fit on the motor housing.
While you remove sprocket housing (35) from the motor housing, inner bearing cone (42)
and outer bearing cones (44) may stay with the sprocket housing or the inner bearing cone
may stay on the motor housing.
31. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Separate the
sprocket housing from the motor housing. The weight of sprocket housing (35) is
approximately 109 kg (240 lb).
Illustration 27 g01208626
32. Remove the locating pins from the motor housing.
33. Remove Duo-Cone seal (41) from the motor housing.
34. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.
Illustration 28 g03431456
35. Remove Duo-Cone seal (43) from the sprocket housing.
36. If outer bearing cone (44) remained on the sprocket housing, then remove the outer bearing
cone.
37. Remove the bearing cups from the sprocket housing.
11/12(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR JFR
Configuration: 330F & 330F LN Excavators JFR00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326F, 329F and 330F Excavators Machine Systems
Media Number -UENR3313-07 Publication Date -01/09/2015 Date Updated -12/09/2018
i07332931
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Stand Group 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 138-7575 Link Bracket 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G
8T-9206 Duo-Cone Seal Installer As 1
169-0503 Installation Kit 1
H - Loctite C5A Copper Antiseize -
J - Loctite 242 Threadlocker -
K - Loctite Highflex GM -
L FT-2770 Leak down Test Tool 1
1. Make sure that all parts of the final drive are thoroughly clean and free of dirt and debris
prior to assembly. Check the condition of all O-ring seals that are used in the final drive. If
any of the seals are damaged, use new parts for replacement. Reassemble the final drive on
Tooling (A).
1/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 1 g03431464
Note: New final drives are equipped with angular contact ball bearings.
2. Apply Tooling (H) to the surfaces inside sprocket housing (35) that contacts the bearing
cups. Install a bearing cup that is in each side of the sprocket housing with a press. Make
sure that the bearing cups are properly seated.
3. Apply Tooling (H) to the surfaces inside the sprocket housing that contacts bearing cones
(44).
4. Install outer bearing cone (44) in the sprocket housing.
Illustration 2 g01208625
5. Attach Tooling (F) and a suitable lifting device to sprocket housing (35). The weight of
sprocket housing (35) is approximately 109 kg (240 lb). Install sprocket housing (35) on the
motor housing. Carefully install inner bearing cone (42) on the sprocket housing.
2/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 3 g01208578
6. Adjust the bearing preload of the final drive. Determine the correct number of shims (40)
that are required for the proper bearing preload, as follows:
Note: New final drives are equipped with angular contact ball bearings that require pre-load
like the old roller bearings.
Illustration 4 g01208987
a. Use a depth micrometer to measure the step height of coupling gear (38) at several
locations around the gear. Find the average for the measured dimensions around the
gear and record the dimension. Call this Dimension (X).
b. Apply a load of 4000 kg (8820 lb) to the bearing cones.
c. Rotate sprocket housing (35) several times to seat the bearing cones.
d. Reduce the load to 1000 ± 100 kg (2205 ± 220 lb).
3/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 5 g00631001
e. With the bearing cones loaded, measure the distance between the top face of the
motor housing and the top face of the bearing cone. Take measurements in several
locations around the motor housing. Find the average of the measured dimensions,
and record the dimensions. Call this Dimension (Y).
f. Determine the correct thickness of the shims which are used between the bearing
cones and the coupling gear . Use the following equation to determine the shim pack
thickness.
Shim pack thickness ... (Y) − (X) ± 0.05 mm (0.002 inch)
Note: If two shims are required, install the thinnest shim next to the coupling gear
during final assembly.
Illustration 6 g03431699
7. Attach Tooling (F) and a suitable lifting device to sprocket housing (35). Separate sprocket
housing (35) from the motor housing.
Reference: Refer to Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contacts the seals must be clean and dry. After
installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal seals.
4/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 7 g00631006
Illustration 8 g01208999
8. Use Tooling (G) to install Duo-Cone seal (43) in the sprocket housing.
Illustration 9 g00631014
5/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 10 g03431475
9. Use Tooling (G) to install Duo-Cone seal (41) in the motor housing.
10. Apply Tooling (H) in the bores for the locating pins that are in the motor housing. Reinstall
the locating pins in the motor housing.
Illustration 11 g01208625
11. Make sure that inner bearing cone (42) is seated properly on the motor housing.
Note: Do not scratch Duo-Cone seal (41) or damage the Duo-Cone seal in the main
housing, or the motor housing during assembly of the two components. After installation of
the main housing on the motor housing, there will be a small gap between the components.
The gap between the components is caused by the Duo-Cone seal. The gap will be
eliminated during the installation of the coupling gear .
12. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Carefully install
the sprocket housing on the motor housing.
13. Install the outer bearing cone on the sprocket housing. Make sure that the outer bearing cone
is properly seated.
6/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 12 g01208578
14. Install shims (40) that were determined in Steps 6.a through 6.f on the end of the sprocket
housing. If shims were required, make sure that the thinnest shim is installed on top.
Illustration 13 g01208553
15. Put coupling gear (38) in the original position on the motor housing.
16. Apply Tooling (J) on the threads of bolts (37) that hold coupling gear (38) in position.
Tighten bolts (37) evenly and tighten the bolts in diagonally opposite pairs to a torque of
570 ± 80 N·m (420 ± 60 lb ft).
Illustration 14 g01208542
7/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 17. Install O-ring seal (36) in sprocket housing (35).
Illustration 15 g01208300
18. Thoroughly clean the mating surface of sprocket housing (35) that contacts ring gear (34).
19. Apply a bead of Tooling (K) on the mating surface of ring gear (34).
20. Attach Tooling (E) and a suitable lifting device to ring gear (34). Put ring gear (34) in
position on the sprocket housing. The weight of ring gear (34) is approximately 66 kg
(146 lb). Make sure that the alignment mark upon the sprocket housing and the ring gear
line with each other.
Illustration 16 g01843479
8/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 17 g00893674
21. Assemble carrier assembly (28), as follows.
a. Install bearings (32) in planetary gear (33).
b. Install thrust washers (31) and planetary gear (33) in the carrier assembly.
c. Use a deburring tool to remove the metal burr from the openings in the carrier. Install
planetary shaft (29) in the carrier assembly.
d. Drive spring pin (30) into planetary shaft (29).
Illustration 18 g00941047
The stake mark is at position (S).
e. Orient the split in spring pin (30) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 2.25 ± 0.75 mm
(0.089 ± 0.030 inch) from the outside diameter of the spring pin hole.
22. Repeat Steps 21.a through 21.e to install the other two planetary gears in the carrier
assembly.
9/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 19 g01842974
23. Use two people to install carrier assembly (28). The weight of carrier assembly (28) is
approximately 38 kg (85 lb).
Illustration 20 g01842853
24. Install spacer (27A). Install gear (27).
Illustration 21 g00897548
10/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 22 g00896863
25. Assemble planetary carrier (19), as follows.
a. Install bearing (25) in planetary gear (26).
b. Install thrust washers (24) and planetary gear (26) in the planetary carrier.
c. Use a deburring tool to remove the metal burr from the openings in the carrier. Install
planetary shaft (22) in planetary carrier (19).
d. Drive spring pin (23) into planetary shaft (22).
Illustration 23 g00941047
The stake mark is at position (S).
e. Orient the split in spring pin (23) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 2.25 ± 0.75 mm
(0.089 ± 0.030 inch) from the outside diameter of the spring pin hole.
f. Repeat Steps 25.a through 25.e to install the other two planetary gears in the carrier.
11/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 24 g00893019
26. Position sun gear (20) in planetary carrier (19) and install retaining ring (21).
Illustration 25 g00892997
27. Use Tooling (D) and a suitable lifting device to install planetary carrier (19) into gear (34).
The weight of planetary carrier (19) is approximately 48 kg (105 lb).
Illustration 26 g00892977
28. Install spacer (18) and gear (17).
12/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 27 g01389807
Note: Make sure that the oil passages in the shafts are oriented toward the center of carrier
assembly (16).
29. Raise the temperature of carrier assembly (16). Lower the temperature of the shafts. Install
the shafts into carrier assembly (16) until the groove of the shafts is at Dimension (A).
Dimension (A) equals 25.00 ± 0.10 mm (0.984 ± 0.004 inch).
30. Make eight stake marks at distance of Dimension (C) from each shaft. Dimension (C)
equals 2.0 ± 1.0 mm (0.08 ± 0.04 inch). The width of each stake mark should be equal to
Dimension (B). Dimension (B) equals 4.0 ± 1.0 mm (0.16 ± 0.04 inch).
Illustration 28 g00892975
13/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. 31. Install carrier assembly (16).
Illustration 29 g00892968
32. Install retaining ring (15).
Illustration 30 g00892965
33. Install washer (14) and bearing assembly (13). Install gear (12) and washer (11). Use
Tooling (C) to install retaining ring (10).
34. Repeat Step 33 for the other two planetary gears.
Illustration 31 g00780428
14/17(W)
w
2020/6/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...