This document provides instructions for servicing components of a Caterpillar 330C FM excavator engine. It describes procedures for removing and installing the cylinder head, which involves draining coolant, removing various attached components, and using lifting equipment due to the head's weight of 147 kg. Instructions are also given for installing the cylinder head, including torquing bolts in a specific sequence and reattaching hoses and sensors. Additional procedures describe removing and installing the lifter group from the cylinder block.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...shudun96087
This document provides instructions for servicing components of a Caterpillar 330C FM excavator engine. It describes how to remove and install the cylinder head, which involves draining coolant, removing accessories, sensors and bolts, and lifting the head off. It also details removing and installing the lifter group by using tools to pull lifters from the cylinder block and lubricating them before replacing in their original locations. Precautions are given to keep parts clean and contain fluids during repair work.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...cnp692569
This document provides instructions for installing a camshaft on a Caterpillar C9 engine. It begins by noting the required tools and keeping parts clean. It then instructs to set the #1 piston to top center, align the camshaft and idler gear timing marks, apply lubricant to the camshaft, and position the camshaft in the cylinder block. It concludes by noting to install the thrust plate and bolts while ensuring the camshaft lobes and bearings are not damaged.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...kesi7153062
This document provides instructions for installing a camshaft on a Caterpillar C9 engine. It begins by noting the required tools and keeping parts clean. It then instructs to set the #1 piston to top center, align the camshaft and idler gear timing marks, apply lubricant to the camshaft, and position the camshaft in the cylinder block. It concludes by noting to install the thrust plate and bolts while ensuring the camshaft lobes and bearings are not damaged.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B2L) Service Repair Manual (B2L0000...jdjkskmikdkmd
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various accessories, and using lifting tools to remove the cylinder head. The installation procedure outlines reinstalling gaskets and accessories and tightening bolts in a specific sequence. Instructions are also provided for removing the camshaft by aligning timing marks and repositioning lifters, and installing the camshaft by lubricating parts and ensuring proper timing of gears.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B2L) Service Repair Manual Instant ...yan77xunhao
This document provides instructions for removing and installing various engine components on a Caterpillar 330C FM EXCAVATOR including:
- Cylinder head removal which requires draining coolant and removing accessories before removing bolts and lifting off the head.
- Cylinder head installation which involves positioning a new gasket and torquing bolts in a specific sequence.
- Lifter group removal by using a hook tool to remove individual lifters and mark them for reinstallation.
- Lifter group installation by lubricating lifters and reinstalling them in the original locations.
- Camshaft removal which requires setting the engine to top dead center and aligning timing marks before
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...udjdkkmdmdm
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator engine. The removal process involves draining coolant, removing various accessories, and using lifting tools to remove the cylinder head. The installation process details cleaning and lubricating parts, torquing bolts in a specific sequence, and reinstalling accessories. Correct timing of gears is emphasized for proper engine function.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fikkskkdmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 330C FM EXCAVATOR including:
- Cylinder head removal which requires draining coolant and removing accessories before removing bolts and lifting off the head.
- Cylinder head installation which involves positioning a new gasket and torquing bolts in a specific sequence.
- Lifter group removal by using a hook tool to remove individual lifters and mark them for installation.
- Lifter group installation by applying lubricant to lifters before reinstalling them in the original locations.
- Camshaft removal which requires setting the #1 piston at top center and aligning timing
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...shudun96087
This document provides instructions for servicing components of a Caterpillar 330C FM excavator engine. It describes how to remove and install the cylinder head, which involves draining coolant, removing accessories, sensors and bolts, and lifting the head off. It also details removing and installing the lifter group by using tools to pull lifters from the cylinder block and lubricating them before replacing in their original locations. Precautions are given to keep parts clean and contain fluids during repair work.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...cnp692569
This document provides instructions for installing a camshaft on a Caterpillar C9 engine. It begins by noting the required tools and keeping parts clean. It then instructs to set the #1 piston to top center, align the camshaft and idler gear timing marks, apply lubricant to the camshaft, and position the camshaft in the cylinder block. It concludes by noting to install the thrust plate and bolts while ensuring the camshaft lobes and bearings are not damaged.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...kesi7153062
This document provides instructions for installing a camshaft on a Caterpillar C9 engine. It begins by noting the required tools and keeping parts clean. It then instructs to set the #1 piston to top center, align the camshaft and idler gear timing marks, apply lubricant to the camshaft, and position the camshaft in the cylinder block. It concludes by noting to install the thrust plate and bolts while ensuring the camshaft lobes and bearings are not damaged.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B2L) Service Repair Manual (B2L0000...jdjkskmikdkmd
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various accessories, and using lifting tools to remove the cylinder head. The installation procedure outlines reinstalling gaskets and accessories and tightening bolts in a specific sequence. Instructions are also provided for removing the camshaft by aligning timing marks and repositioning lifters, and installing the camshaft by lubricating parts and ensuring proper timing of gears.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B2L) Service Repair Manual Instant ...yan77xunhao
This document provides instructions for removing and installing various engine components on a Caterpillar 330C FM EXCAVATOR including:
- Cylinder head removal which requires draining coolant and removing accessories before removing bolts and lifting off the head.
- Cylinder head installation which involves positioning a new gasket and torquing bolts in a specific sequence.
- Lifter group removal by using a hook tool to remove individual lifters and mark them for reinstallation.
- Lifter group installation by lubricating lifters and reinstalling them in the original locations.
- Camshaft removal which requires setting the engine to top dead center and aligning timing marks before
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...udjdkkmdmdm
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator engine. The removal process involves draining coolant, removing various accessories, and using lifting tools to remove the cylinder head. The installation process details cleaning and lubricating parts, torquing bolts in a specific sequence, and reinstalling accessories. Correct timing of gears is emphasized for proper engine function.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fikkskkdmmd
This document provides instructions for removing and installing various engine components on a Caterpillar 330C FM EXCAVATOR including:
- Cylinder head removal which requires draining coolant and removing accessories before removing bolts and lifting off the head.
- Cylinder head installation which involves positioning a new gasket and torquing bolts in a specific sequence.
- Lifter group removal by using a hook tool to remove individual lifters and mark them for installation.
- Lifter group installation by applying lubricant to lifters before reinstalling them in the original locations.
- Camshaft removal which requires setting the #1 piston at top center and aligning timing
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar Cat 330D and 330D L Excavator (Prefix GBC) Service Repair Manual ...f89siekkmdmm2w
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the proper sequence for installing mounting bolts are also included.
Caterpillar Cat 330D and 330D L Excavator (Prefix GBC) Service Repair Manual ...f8uejkdkdmm3e
This service repair manual provides instructions for repairing and reassembling parts of the 330D and 330D L excavator models. It describes how to remove and install the cylinder head, camshaft, lifter group, and rocker arm and shaft. Detailed steps are provided, including necessary tools and torque specifications. Safety notices advise keeping parts clean and taking care when handling heavy components.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...fuusejkddmmd3e
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the correct sequence for installing mounting bolts are also provided.
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is important during installation.
Caterpillar Cat 330D and 330D L Excavator (Prefix GBC) Service Repair Manual ...shibi1322
The document provides instructions for removing and installing a cylinder head on a Caterpillar C9 engine. It outlines the required tools and gives step-by-step procedures for removing the cylinder head which involves draining coolant, removing mounting bolts and cables, and lifting the head off. Instructions for installing the cylinder head include positioning the gasket, tightening bolts in a specific sequence, and reconnecting cables before refilling the cooling system.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...diskdkkdmmd
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It describes:
1) Removing the rocker arm shaft, front cover, and valve lifters before removing the camshaft.
2) Aligning timing marks and removing bolts and thrust plate to access the camshaft.
3) Lubricating and carefully installing the camshaft, rotating it to prevent binding in the bearings.
Caterpillar Cat 330D and 330D L Excavator (Prefix GBC) Service Repair Manual ...fucheng89
This service repair manual provides instructions for repairing and reassembling parts of the 330D and 330D L excavator models. It describes how to remove and install the cylinder head, camshaft, lifter group, and rocker arm and shaft. Detailed steps are provided, including necessary tools and torque specifications. Safety notices advise keeping parts clean and taking care when handling heavy components.
The document provides instructions for removing and installing various components of an excavator engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, and exhaust manifold. The procedures include required tools, safety warnings, step-by-step instructions, and torque specifications for reinstallation.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to contain hydraulic fluids.
This document provides disassembly instructions for the travel motor on a 336F L XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing the head, springs, relief valves, pistons, barrel assembly, swashplate and other internal components. Detailed illustrations accompany each step to show how to properly remove parts and note their positions for reassembly. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly.
Caterpillar Cat 336F L XE Excavator (Prefix MTW) Service Repair Manual (MTW00...jdksmmdmdd
This document provides disassembly instructions for a travel motor on a 336F LN XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations accompany each step to show how to remove each part in the proper sequence. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly. Required tools are listed that will be needed to complete the process.
Caterpillar Cat 336F L XE Excavator (Prefix YBH) Service Repair Manual (YBH00...jdksmmdmdd
This document provides instructions for disassembling the travel motor on a 336F LNXE excavator. The 27 step procedure includes removing components like the motor head assembly, barrel assembly, piston assemblies, springs, seals, plates and more. Special care must be taken when removing components under spring pressure. Tools and safety precautions are listed for each step. The goal is to disassemble all parts while keeping them organized for proper reassembly.
This document provides instructions to disassemble a travel motor on a 349F and 349F L excavator. It outlines 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, port plate, springs, seals, bearings, valves and more. Precautions are provided to be aware of parts under spring force. Various specialized tools are required to properly support, attach, extract and remove components from the motor.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a hydraulic fan drive for an excavator. It details 22 steps for disassembly, removing components like bolts, retainers, seals, discs, and housing pieces. It then details 14 steps for reassembly, including pressing in bearings and seals, installing retaining rings, and pressing the shaft assembly back into place using the proper tools. Cleanliness is emphasized throughout to prevent contamination of precision components.
Caterpillar Cat 349E L Excavator (Prefix KFX) Service Repair Manual (KFX00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Personal protective equipment is recommended when removing parts with stored spring energy. Tools include lifting devices, bolts, nuts, and specialized pullers and presses. Drained fluids must be contained and disposed of properly.
Caterpillar Cat 349E L Excavator (Prefix MPZ) Service Repair Manual (MPZ00001...jdksmmdmdd
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts.
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Precise torques and specifications are provided to ensure correct reassembly.
Caterpillar Cat 349D2 L Excavator (Prefix RAN) Service Repair Manual (RAN0000...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pistons, and housing. Precautions are provided to keep parts clean and in correct orientation during reassembly.
This document provides instructions for removing and installing the rear gear group on a 349D2 and 349D2 L excavator powered by a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, bushings and bearings. The installation procedure involves 12 steps including lowering temperatures of bearings before installation, applying sealant to bolts, and ensuring proper dimensions are met. Tools including drivers and installer are required.
The document provides instructions for disassembling a travel motor. It lists the required tools and gives step-by-step instructions to remove parts like the head, plates, seals, pins, and more. Safety notices are included to handle parts carefully and avoid contamination when disassembling components.
Caterpillar Cat 349D2 L Excavator (Prefix GAX) Service Repair Manual (GAX0000...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, reinstalling these components in reverse order and noting to clean all parts and replace seals and gaskets. Precautions are provided to contain fluids, mark parts locations, and avoid contaminating the hydraulic system.
More Related Content
Similar to Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K00001 and up).pdf
Caterpillar Cat 330D and 330D L Excavator (Prefix GBC) Service Repair Manual ...f89siekkmdmm2w
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the proper sequence for installing mounting bolts are also included.
Caterpillar Cat 330D and 330D L Excavator (Prefix GBC) Service Repair Manual ...f8uejkdkdmm3e
This service repair manual provides instructions for repairing and reassembling parts of the 330D and 330D L excavator models. It describes how to remove and install the cylinder head, camshaft, lifter group, and rocker arm and shaft. Detailed steps are provided, including necessary tools and torque specifications. Safety notices advise keeping parts clean and taking care when handling heavy components.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...fuusejkddmmd3e
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the correct sequence for installing mounting bolts are also provided.
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is important during installation.
Caterpillar Cat 330D and 330D L Excavator (Prefix GBC) Service Repair Manual ...shibi1322
The document provides instructions for removing and installing a cylinder head on a Caterpillar C9 engine. It outlines the required tools and gives step-by-step procedures for removing the cylinder head which involves draining coolant, removing mounting bolts and cables, and lifting the head off. Instructions for installing the cylinder head include positioning the gasket, tightening bolts in a specific sequence, and reconnecting cables before refilling the cooling system.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...diskdkkdmmd
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It describes:
1) Removing the rocker arm shaft, front cover, and valve lifters before removing the camshaft.
2) Aligning timing marks and removing bolts and thrust plate to access the camshaft.
3) Lubricating and carefully installing the camshaft, rotating it to prevent binding in the bearings.
Caterpillar Cat 330D and 330D L Excavator (Prefix GBC) Service Repair Manual ...fucheng89
This service repair manual provides instructions for repairing and reassembling parts of the 330D and 330D L excavator models. It describes how to remove and install the cylinder head, camshaft, lifter group, and rocker arm and shaft. Detailed steps are provided, including necessary tools and torque specifications. Safety notices advise keeping parts clean and taking care when handling heavy components.
Similar to Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K00001 and up).pdf (7)
The document provides instructions for removing and installing various components of an excavator engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, and exhaust manifold. The procedures include required tools, safety warnings, step-by-step instructions, and torque specifications for reinstallation.
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to contain hydraulic fluids.
This document provides disassembly instructions for the travel motor on a 336F L XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing the head, springs, relief valves, pistons, barrel assembly, swashplate and other internal components. Detailed illustrations accompany each step to show how to properly remove parts and note their positions for reassembly. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly.
Caterpillar Cat 336F L XE Excavator (Prefix MTW) Service Repair Manual (MTW00...jdksmmdmdd
This document provides disassembly instructions for a travel motor on a 336F LN XE excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and more. Detailed illustrations accompany each step to show how to remove each part in the proper sequence. Safety precautions are provided to warn of potential spring forces and contain fluids during disassembly. Required tools are listed that will be needed to complete the process.
Caterpillar Cat 336F L XE Excavator (Prefix YBH) Service Repair Manual (YBH00...jdksmmdmdd
This document provides instructions for disassembling the travel motor on a 336F LNXE excavator. The 27 step procedure includes removing components like the motor head assembly, barrel assembly, piston assemblies, springs, seals, plates and more. Special care must be taken when removing components under spring pressure. Tools and safety precautions are listed for each step. The goal is to disassemble all parts while keeping them organized for proper reassembly.
This document provides instructions to disassemble a travel motor on a 349F and 349F L excavator. It outlines 27 steps to fully disassemble the travel motor, removing components like the motor head assembly, port plate, springs, seals, bearings, valves and more. Precautions are provided to be aware of parts under spring force. Various specialized tools are required to properly support, attach, extract and remove components from the motor.
Caterpillar Cat 349E L Excavator (Prefix FJB) Service Repair Manual (FJB00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a hydraulic fan drive for an excavator. It details 22 steps for disassembly, removing components like bolts, retainers, seals, discs, and housing pieces. It then details 14 steps for reassembly, including pressing in bearings and seals, installing retaining rings, and pressing the shaft assembly back into place using the proper tools. Cleanliness is emphasized throughout to prevent contamination of precision components.
Caterpillar Cat 349E L Excavator (Prefix KFX) Service Repair Manual (KFX00001...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor on a 349E L VG excavator. It includes 27 steps for disassembly and 18 steps for assembly. Key parts that are removed and installed include the head assembly, brake housing, rotating group, barrel assembly, pistons, bearings and seals. Tools and torque specifications are provided for correct disassembly and reassembly.
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Personal protective equipment is recommended when removing parts with stored spring energy. Tools include lifting devices, bolts, nuts, and specialized pullers and presses. Drained fluids must be contained and disposed of properly.
Caterpillar Cat 349E L Excavator (Prefix MPZ) Service Repair Manual (MPZ00001...jdksmmdmdd
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts.
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Precise torques and specifications are provided to ensure correct reassembly.
Caterpillar Cat 349D2 L Excavator (Prefix RAN) Service Repair Manual (RAN0000...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pistons, and housing. Precautions are provided to keep parts clean and in correct orientation during reassembly.
This document provides instructions for removing and installing the rear gear group on a 349D2 and 349D2 L excavator powered by a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, bushings and bearings. The installation procedure involves 12 steps including lowering temperatures of bearings before installation, applying sealant to bolts, and ensuring proper dimensions are met. Tools including drivers and installer are required.
The document provides instructions for disassembling a travel motor. It lists the required tools and gives step-by-step instructions to remove parts like the head, plates, seals, pins, and more. Safety notices are included to handle parts carefully and avoid contamination when disassembling components.
Caterpillar Cat 349D2 L Excavator (Prefix GAX) Service Repair Manual (GAX0000...jdksmmdmdd
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, reinstalling these components in reverse order and noting to clean all parts and replace seals and gaskets. Precautions are provided to contain fluids, mark parts locations, and avoid contaminating the hydraulic system.
The document provides instructions for removing and installing various components of an excavator engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, and exhaust manifold. The procedures include required tools, safety warnings, step-by-step instructions, and torque specifications for reinstallation.
This document provides instructions for removing and installing various engine components on a C13 engine, including:
1. Removing the rear gear group by removing bolts, seals, gears, bushings, and bearings.
2. Removing the flywheel by attaching lifting tools and removing bolts.
3. Removing the crankshaft rear seal by removing bolts. Detailed steps and illustrations are provided for each procedure. Required tools are listed.
This document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like plates and seals. It then describes removing the head, brake piston, disks, and rotating group. Components like the shaft, bearings, and pistons are then removed from the rotating group. Reassembly involves reversing these steps and ensuring components like O-rings and washers are properly installed. Precautions are provided to prevent contamination and correctly identify parts.
Caterpillar Cat 336D2 L Excavator (Prefix FAJ) Service Repair Manual (FAJ0000...jdksmmdmdd
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools.
This document provides instructions for disassembling the travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 27 steps to remove parts like the motor head assembly, springs, pistons, seals, plates and other components. Various tools are required including bolts, retaining ring pliers, drivers and pullers. Precautions are mentioned to relieve spring pressure safely and contain fluids. The process yields individual parts to allow inspection and replacement of worn items.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B1K
Configuration: 330C Forest Swing Machines B1K00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i04506590
Rocker Arm and Shaft - Install
SMCS - 1102-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-2998 Lubricant -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Apply Tooling (A) to both ends of the pushrods.
2. Lubricate the pushrods with clean engine oil. Install the pushrods and the valve bridges.
1/3(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00953116
3. Position rocker shaft (4) on the cylinder head. Install bolts (1).
Illustration 2 g02685496
Rocker shaft hold down bolts tightening sequence
4. Tighten bolts (1) in the sequence shown. Tighten bolts (1) to standard torque.
2/3(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 5. Apply Tooling (A) to each of the bottom faces of the rocker arms.
6. Position rocker arm adjustment screws (2) and tighten nuts (3). Adjust the valve lash of the
rocker arms. Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust".
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 12:36:20 UTC+0800 2020
3/3(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B1K
Configuration: 330C Forest Swing Machines B1K00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02273201
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
Start By:
A. Remove the rocker arm and shaft. Refer to Disassembly and Assembly, "Rocker Arm and
Shaft - Remove".
B. Remove the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
C. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
D. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/3(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations".
2/3(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 1 g01063034
2. Remove accessory drive group (1) .
3. Disconnect tube assemblies (3) and (4) .
4. Remove tube assembly (2) .
5. Disconnect hose (5) .
Illustration 2 g01142119
6. Disconnect hose assemblies (6) and (7) .
7. Disconnect the sensors.
8. Attach Tooling (A) and a suitable lifting device to cylinder head (9). The weight of cylinder
head (9) is approximately 147 kg (325 lb).
9. Remove bolts (8). Remove cylinder head (9) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 12:37:16 UTC+0800 2020
3/3(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B1K
Configuration: 330C Forest Swing Machines B1K00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i05919858
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 4C-5593 Anti-Seize Compound 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Position a new gasket on the engine.
1/5(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 1 g01142119
2. Attach Tooling (A) and a suitable lifting device to cylinder head (9) . The weight of cylinder head (9)
is approximately 147 kg (325 lb). Position the cylinder head onto the dowels in the engine block.
3. Apply Tooling (B) to the threads of bolts (8) . Install bolts (8) .
Tighten the plugs (not shown) for the high-pressure oil gallery on each end of the cylinder head to
the following torque 285 ± 25 N·m (210 ± 18 lb ft).
Note: Refer to Reuse and Salvage Guidelines, SEBF8301, "Inspection and Reuse of Critical
Fasteners Used in All Engines" for reuse criteria of bolts (8) .
Illustration 2 g01063104
4. Tighten bolts (8) according to the following procedure:
a. Tighten Bolt (1) through Bolt (26) in a numerical sequence to a torque of 160 ± 15 N·m (118 ±
11 lb ft).
b. Loosen Bolt (1) through Bolt (26) until the washers are loose under the bolt heads.
2/5(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. c. Tighten Bolt (1) through Bolt (26) again in a numerical sequence to a torque of 160 ± 15 N·m
(118 ± 11 lb ft).
d. Place a mark on Bolt (1) through Bolt (26) .
e. Rotate Bolt (1) through Bolt (26) in a numerical sequence. Rotate the bolts in the clockwise
direction for 90 degrees (1/4 turn) from the mark on the bolts.
f. Loosen Bolt (1) through Bolt (26) until the washers are loose under the bolt heads.
g. Tighten Bolt (1) through Bolt (26) in a numerical sequence to a torque of 160 ± 15 N·m (118 ±
11 lb ft).
h. Place a mark on Bolt (1) through Bolt (26) .
i. Rotate Bolt (1) through Bolt (26) in a numerical sequence. Rotate the bolts in the clockwise
direction for 90 degrees (1/4 turn) from the mark on the bolts.
j. Tighten Bolt (27) through Bolt (31) in a numerical sequence to a torque of 28 ± 7 N·m (21 ± 5
lb ft).
Tighten the plugs (not shown) for the high-pressure oil gallery on each end of the cylinder
head to the following torque 285 ± 25 N·m (210 ± 18 lb ft).
5. Connect the sensors.
6. Connect hose assemblies (6) and (7) .
3/5(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 3 g01063034
7. Connect hose (5) .
8. Install tube assembly (2) .
9. Connect tube assemblies (3) and (4) .
10. Install accessory drive group (1) .
11. Fill the cooling system. Refer to Operation and Maintenance Manual, "Refill Capacities and
Recommendations".
End By:
a. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism
Cover Base - Remove and Install".
b. Install the alternator. Refer to Disassembly and Assembly, " Alternator - Remove and Install".
c. Install the unit injectors. Refer to Disassembly and Assembly , "Unit Injector - Install".
d. Install the rocker arm and shaft. Refer to Disassembly and Assembly , "Rocker Arm and Shaft -
Install".
Sat Sep 12 12:38:12 UTC+0800 2020
4/5(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B1K
Configuration: 330C Forest Swing Machines B1K00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i06809044
Lifter Group - Remove and Install
SMCS - 1209-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2730 Hook 1
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 1 g00953158
1. Use Tooling (A) to remove valve lifters (1). Place identification marks on the valve lifters
for installation purposes.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A FT-2730 Hook 1
B 8T-2998 Lubricant 1
2/3(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 2 g00953158
1. Apply Tooling (B) to valve lifters (1) prior to installation. Use Tooling (A) to install valve
lifters (1) in the original location in the cylinder block.
End By:
a. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 12:39:07 UTC+0800 2020
3/3(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B1K
Configuration: 330C Forest Swing Machines B1K00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02274059
Camshaft - Remove
SMCS - 1210-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2730 Hook 12
Start By:
a. Remove the rocker arm and the shaft. Refer to Disassembly and Assembly, "Rocker Arm
and Shaft - Remove".
b. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Use Tooling (A) to reposition the valve lifters out of the way of the camshaft.
2. Set the No. 1 piston to top center on the compression stroke. Refer to Testing and Adjusting,
"Finding Top Center Position for No. 1 Piston".
1/3(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 1 g01032348
3. Ensure that the timing marks on camshaft gear (1) and idler gear (2) are aligned.
4. Remove bolts (3) and thrust plate (4) from the cylinder block.
Illustration 2 g01032349
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2/3(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. 5. Remove camshaft (5) from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 12:40:03 UTC+0800 2020
3/3(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B1K
Configuration: 330C Forest Swing Machines B1K00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i05278252
Camshaft - Install
SMCS - 1210-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2730 Hook 12
B 8T-2998 Lubricant -
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 1 g03356215
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
Note: During the installation of the camshaft, rotate the camshaft in both directions in order to
prevent binding in the camshaft bearing bores.
1. Lubricate the camshaft lobes and the valve lifter bore with a 50/50 mixture of Tooling (B). Apply
clean engine oil on the camshaft bearing journals. Carefully install camshaft (10) in the cylinder
block.
2/4(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 2 g03356207
(5) Gear for the high-pressure fuel pump
(6) Camshaft gear
(7) Idler gear
(8) Crankshaft gear
(9) Timing marks
NOTICE
When installing the camshaft, make sure the number one cylinder is at
top center of the compression stroke with the timing bolt installed in
the flywheel. The camshaft timing is very important. The timing mark
on the camshaft drive gear must line up with the timing mark on the
idler gear. Refer to the Specifications Manual for more information.
2. Correct fuel injection timing and correct valve mechanism operation is determined by properly
timing crankshaft gear (8) and camshaft gear (6) to idler gear (7). Also, high-pressure fuel pump gear
(5) must be timed to camshaft gear (6). During installation of the front gear, timing marks (9) on
idler gear (7) must be in alignment with the timing marks on crankshaft gear (8) and the timing
marks on camshaft gear (6). The "0" mark on camshaft gear (6) must align with the timing mark on
idler gear (7). The "V" mark on camshaft gear (6) must align with the "V" mark on fuel pump gear
(5).
3/4(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 3 g01032348
3. Install thrust plate (4) and bolts (3).
4. The maximum permissible end play for a worn camshaft is 0.46 mm (0.018 inch). The maximum
permissible end play for a new camshaft is 0.13 ± 0.08 mm (0.005 ± 0.003 inch).
5. Use Tooling (A) to position the valve lifters in the cylinder block.
6. Calibrate the speed/timing sensor. Refer to Troubleshooting, "Engine Speed/Timing Sensor -
Calibrate".
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
b. Install the rocker arm and the shaft. Refer to Disassembly and Assembly, "Rocker Arm and Shaft -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 12:40:59 UTC+0800 2020
4/4(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B1K
Configuration: 330C Forest Swing Machines B1K00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02408922
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
1. Wrap the camshaft with a protective covering in order to prevent damage to the camshaft.
Illustration 1 g01142107
NOTICE
1/2(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Do not allow the camshaft to fall to the floor when pressing it from the
drive gear. Also make sure that the camshaft lobes do not catch on the
press plates.
2. Use a suitable press to remove the camshaft from camshaft gear (1).
Installation Procedure
Note: The temperature of the camshaft gear must not exceed 177 °C (350 °F) during
installation.
1. Raise the temperature of the camshaft gear up to a temperature of 177 °C (350 °F).
2. Align the key in the camshaft with the groove (keyway) in the camshaft gear.
3. Install the camshaft gear on the end of the camshaft.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 12:41:55 UTC+0800 2020
2/2(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B1K
Configuration: 330C Forest Swing Machines B1K00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02545687
Camshaft Bearings - Remove
SMCS - 1211-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
b. Remove the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing-
Remove and Install".
Note: Note the oil hole orientation in each camshaft bearing prior to removal for assembly
purposes.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/2(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00633159
1. Use Tooling (A) to remove the camshaft bearings from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 12 12:42:51 UTC+0800 2020
2/2(W)
w
2020/9/12
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...