The document provides instructions for removing, disassembling, assembling, and installing a compression brake on a 330B excavator engine. It describes removing the valve mechanism cover and then compression brake components. Disassembly steps include removing seals, springs, pistons and other parts. Assembly is the reverse of disassembly. Installation involves reinstalling the compression brake components and valve mechanism cover. Separate sections provide instructions for removing, assembling, and installing rocker shafts and pushrods.
The document provides instructions for removing, disassembling, and assembling a compression brake on a Caterpillar D7R track-type tractor. It describes removing the valve mechanism cover, then compression brake components like bolts, wires, pistons, springs, and oil tubes. Disassembly involves removing additional parts like retaining rings, clips, and seals. Reassembly requires installing these same components in reverse order while ensuring cleanliness to prevent wear.
The document provides instructions for removing, disassembling, and assembling a compression brake on a Caterpillar D7R track-type tractor. It describes removing the valve mechanism cover, then compression brake components like bolts, wires, pistons, springs, and oil tubes. Disassembly involves removing additional parts like retaining rings, clips, and seals. Reassembly requires installing these same components in reverse order while ensuring cleanliness to prevent premature wear.
The document provides instructions for removing, disassembling, and assembling a compression brake on a Caterpillar D7R track-type tractor. It describes removing the valve mechanism cover, then compression brake components like bolts, wires, pistons, springs, and oil tubes. Disassembly details removing parts like retaining rings and clips from the brake. Reassembly instructs installing pistons, springs, tubes and other components in reverse order. Similarly, it outlines removing, disassembling and assembling a rocker shaft, including removing supports, arms, springs and installing in reverse.
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...dujkdksmdmdm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, and remove the front cover and gasket.
3. Clean the front cover, housing, and install a new gasket. Use guide studs to position the front cover and hand tighten bolts.
4. Align the front cover and tighten the bolts. Install a new front seal and reinstall any removed components.
This document provides instructions for disassembling and assembling a final drive for 330F and 330F LN excavators. The disassembly procedure involves using various tools to remove 37 individual parts from the final drive assembly, including gears, shafts, housings, seals and bearings. The assembly procedure consists of 30 steps to reinstall the parts in reverse order, noting the proper application of sealants and adjustment of bearing preload using shims. Precise alignment and cleanliness of parts is emphasized throughout.
Caterpillar Cat 330D2 L Excavator (Prefix FEX) Service Repair Manual (FEX0000...dujkdksmdmdm
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
Caterpillar Cat 330D2 L Excavator (Prefix EBP) Service Repair Manual (EBP0000...dujkdksmdmdm
The document provides disassembly instructions for a 330D2 and 330D2 L excavator travel motor in 28 steps. It begins by having the technician thoroughly clean and secure the travel motor vertically before disassembling. The steps then carefully describe removing components like the head, brake piston, plates, seals, bearings, and more. Pictures accompany each step to illustrate the proper procedure. Safety notices are included to handle fluids and springs carefully.
The document provides instructions for removing, disassembling, and assembling a compression brake on a Caterpillar D7R track-type tractor. It describes removing the valve mechanism cover, then compression brake components like bolts, wires, pistons, springs, and oil tubes. Disassembly involves removing additional parts like retaining rings, clips, and seals. Reassembly requires installing these same components in reverse order while ensuring cleanliness to prevent wear.
The document provides instructions for removing, disassembling, and assembling a compression brake on a Caterpillar D7R track-type tractor. It describes removing the valve mechanism cover, then compression brake components like bolts, wires, pistons, springs, and oil tubes. Disassembly involves removing additional parts like retaining rings, clips, and seals. Reassembly requires installing these same components in reverse order while ensuring cleanliness to prevent premature wear.
The document provides instructions for removing, disassembling, and assembling a compression brake on a Caterpillar D7R track-type tractor. It describes removing the valve mechanism cover, then compression brake components like bolts, wires, pistons, springs, and oil tubes. Disassembly details removing parts like retaining rings and clips from the brake. Reassembly instructs installing pistons, springs, tubes and other components in reverse order. Similarly, it outlines removing, disassembling and assembling a rocker shaft, including removing supports, arms, springs and installing in reverse.
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...dujkdksmdmdm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, and remove the front cover and gasket.
3. Clean the front cover, housing, and install a new gasket. Use guide studs to position the front cover and hand tighten bolts.
4. Align the front cover and tighten the bolts. Install a new front seal and reinstall any removed components.
This document provides instructions for disassembling and assembling a final drive for 330F and 330F LN excavators. The disassembly procedure involves using various tools to remove 37 individual parts from the final drive assembly, including gears, shafts, housings, seals and bearings. The assembly procedure consists of 30 steps to reinstall the parts in reverse order, noting the proper application of sealants and adjustment of bearing preload using shims. Precise alignment and cleanliness of parts is emphasized throughout.
Caterpillar Cat 330D2 L Excavator (Prefix FEX) Service Repair Manual (FEX0000...dujkdksmdmdm
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps: 1) marking the final drive parts for reassembly; 2) removing the final drive cover and internal parts like gears, washers, seals and shafts; 3) disassembling the carrier assembly and planetary gears; 4) removing the ring gear and separating the motor and sprocket housings; and 5) taking out the coupling gear and shims. Cleanliness is important to prevent dirt ingress, and tools are needed to remove securing pins, rings, bolts and separate connected parts. Weights of individual parts are also provided.
Caterpillar Cat 330D2 L Excavator (Prefix EBP) Service Repair Manual (EBP0000...dujkdksmdmdm
The document provides disassembly instructions for a 330D2 and 330D2 L excavator travel motor in 28 steps. It begins by having the technician thoroughly clean and secure the travel motor vertically before disassembling. The steps then carefully describe removing components like the head, brake piston, plates, seals, bearings, and more. Pictures accompany each step to illustrate the proper procedure. Safety notices are included to handle fluids and springs carefully.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves removing 37 individual parts in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on setting the bearing preload and installing seals correctly.
The document provides instructions for disassembling an excavator travel motor. It is a 27 step process that includes removing the motor head, brake piston, barrel assembly, cam plate, and other internal components. Special tools are required to properly support and disassemble the motor. Technicians are advised to take care to contain fluids and properly dispose of them.
The document provides instructions for disassembling a final drive component in 3 steps:
1. Remove the final drive assembly and disassemble it by removing the cover, gears, carrier assembly, planetary gears, and ring gear.
2. Disassemble the planetary carrier by removing the shafts, washers, bearings and gears.
3. Remove the ring gear from the sprocket housing, then disassemble the motor housing by removing bolts, shims and a coupling gear.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual (R2D00001...dujkdksmdmdm
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Installation requires matching dimensions and orientations when pressing in new bearings and reinstalling components.
To remove the flywheel, bolts are first removed 180 degrees apart using a guide stud before lifting the flywheel off. Installation involves heating and pressing in a ring gear, lifting the flywheel into place using guide studs, and torquing bolts to the specified value
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...dujkdksmdmdm
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Removing hydraulic hoses and fittings, separating the track, and using a lever puller and vacuum pump to remove the assembly.
2. Lifting the assembly free using lifting brackets and bolts, and removing mounting bolts and seals.
3. Reinstalling seals and components in reverse order, and refilling the hydraulic system. Proper cleaning, safety procedures, and use of anti-seize compound are emphasized.
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual (JLP00001...dujkdksmdmdm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts before disassembly and have additional assistance when removing heavy components weighing over 30kg. The detailed process takes the final drive completely apart down to individual planetary gears and shafts.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...dujkdksmdmdm
The document provides instructions for assembling and installing the swing drive of an excavator. It describes 30 steps for assembling the internal components of the swing drive, including installing bearings, gears, seals, and housing components. It then describes 6 steps for installing the entire assembled swing drive into the excavator frame, including attaching lifting brackets, applying sealant, tightening bolts to the specified torque, and filling it with oil. The overall process installs and secures the fully assembled swing drive subsystem into the excavator.
Caterpillar Cat 330D L Excavator (Prefix ERN) Service Repair Manual (ERN00001...dujkdksmdmdm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive including removing covers, gears, carriers, shafts, seals and housings. Special tools are required including link brackets and forcing bolts to remove components due to their weight, with some parts weighing up to 550kg. Detailed illustrations accompany each step to show how to disassemble the various components.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...dujkdksmdmdm
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the proper sequence for installing mounting bolts are also included.
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key components that are disassembled include the drive housing, three planetary gear assemblies, carrier assemblies, ring gear, and other internal gears, shafts, seals and bearings. Special tools are required for pressing, pulling, and removing components. Proper lifting devices and safety precautions are noted due to the heavy weights of components ranging from 32 to 550 kg.
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like link brackets, forcing bolts, and presses. Cleanliness is important to prevent dirt from entering during reassembly.
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
The document provides instructions for assembling and installing the swing drive of an excavator. It describes applying sealant and installing bearings, gears, housings, and other components in the proper order and orientation. Bolts are tightened to the specified torque using an impact wrench. The completed swing drive is then installed on the excavator frame and filled with oil.
Caterpillar Cat 330C L Excavator (Prefix MCA) Service Repair Manual (MCA00001...dujkdksmdmdm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The disassembly process involves removing 28 different components in a specific sequence. The assembly process reverses the disassembly steps and includes applying thread lock compound and lubricating components before reassembly. Cleanliness is emphasized throughout to prevent contamination.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The disassembly process involves removing 28 different components in a specific sequence. The assembly process reverses the disassembly steps and includes applying thread lock compound and lubricating components before reassembly. Cleanliness is emphasized throughout to prevent contamination.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
Caterpillar Cat 330 L EXCAVATOR (Prefix 8CK) Service Repair Manual (8CK00001 ...dujkdksmdmdm
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar 330 LN excavator. The procedures include using various tools to compress springs, remove and insert components, and check spring forces. Safety notices are provided to keep parts clean and prevent injury from compressed springs.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The travel motor disassembly procedure involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals.
2. Travel motor assembly requires installing components in reverse order, applying thread lock compound and oil, and torquing bolts to specified values.
3. Special tools are required to remove and install bearings, seals, and retaining rings. Marks must be made to ensure pistons and other parts are reinstalled in the original positions.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves removing 37 individual parts in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on setting the bearing preload and installing seals correctly.
The document provides instructions for disassembling an excavator travel motor. It is a 27 step process that includes removing the motor head, brake piston, barrel assembly, cam plate, and other internal components. Special tools are required to properly support and disassemble the motor. Technicians are advised to take care to contain fluids and properly dispose of them.
The document provides instructions for disassembling a final drive component in 3 steps:
1. Remove the final drive assembly and disassemble it by removing the cover, gears, carrier assembly, planetary gears, and ring gear.
2. Disassemble the planetary carrier by removing the shafts, washers, bearings and gears.
3. Remove the ring gear from the sprocket housing, then disassemble the motor housing by removing bolts, shims and a coupling gear.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual (R2D00001...dujkdksmdmdm
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Installation requires matching dimensions and orientations when pressing in new bearings and reinstalling components.
To remove the flywheel, bolts are first removed 180 degrees apart using a guide stud before lifting the flywheel off. Installation involves heating and pressing in a ring gear, lifting the flywheel into place using guide studs, and torquing bolts to the specified value
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual (LRM00001...dujkdksmdmdm
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Removing hydraulic hoses and fittings, separating the track, and using a lever puller and vacuum pump to remove the assembly.
2. Lifting the assembly free using lifting brackets and bolts, and removing mounting bolts and seals.
3. Reinstalling seals and components in reverse order, and refilling the hydraulic system. Proper cleaning, safety procedures, and use of anti-seize compound are emphasized.
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual (JLP00001...dujkdksmdmdm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts before disassembly and have additional assistance when removing heavy components weighing over 30kg. The detailed process takes the final drive completely apart down to individual planetary gears and shafts.
Caterpillar Cat 330D L Excavator (Prefix EDX) Service Repair Manual (EDX00001...dujkdksmdmdm
The document provides instructions for assembling and installing the swing drive of an excavator. It describes 30 steps for assembling the internal components of the swing drive, including installing bearings, gears, seals, and housing components. It then describes 6 steps for installing the entire assembled swing drive into the excavator frame, including attaching lifting brackets, applying sealant, tightening bolts to the specified torque, and filling it with oil. The overall process installs and secures the fully assembled swing drive subsystem into the excavator.
Caterpillar Cat 330D L Excavator (Prefix ERN) Service Repair Manual (ERN00001...dujkdksmdmdm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive including removing covers, gears, carriers, shafts, seals and housings. Special tools are required including link brackets and forcing bolts to remove components due to their weight, with some parts weighing up to 550kg. Detailed illustrations accompany each step to show how to disassemble the various components.
Caterpillar Cat 330D L Excavator (Prefix GBC) Service Repair Manual (GBC00001...dujkdksmdmdm
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the proper sequence for installing mounting bolts are also included.
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key components that are disassembled include the drive housing, three planetary gear assemblies, carrier assemblies, ring gear, and other internal gears, shafts, seals and bearings. Special tools are required for pressing, pulling, and removing components. Proper lifting devices and safety precautions are noted due to the heavy weights of components ranging from 32 to 550 kg.
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like link brackets, forcing bolts, and presses. Cleanliness is important to prevent dirt from entering during reassembly.
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
The document provides instructions for assembling and installing the swing drive of an excavator. It describes applying sealant and installing bearings, gears, housings, and other components in the proper order and orientation. Bolts are tightened to the specified torque using an impact wrench. The completed swing drive is then installed on the excavator frame and filled with oil.
Caterpillar Cat 330C L Excavator (Prefix MCA) Service Repair Manual (MCA00001...dujkdksmdmdm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The disassembly process involves removing 28 different components in a specific sequence. The assembly process reverses the disassembly steps and includes applying thread lock compound and lubricating components before reassembly. Cleanliness is emphasized throughout to prevent contamination.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The disassembly process involves removing 28 different components in a specific sequence. The assembly process reverses the disassembly steps and includes applying thread lock compound and lubricating components before reassembly. Cleanliness is emphasized throughout to prevent contamination.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
Caterpillar Cat 330 L EXCAVATOR (Prefix 8CK) Service Repair Manual (8CK00001 ...dujkdksmdmdm
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar 330 LN excavator. The procedures include using various tools to compress springs, remove and insert components, and check spring forces. Safety notices are provided to keep parts clean and prevent injury from compressed springs.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The travel motor disassembly procedure involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals.
2. Travel motor assembly requires installing components in reverse order, applying thread lock compound and oil, and torquing bolts to specified values.
3. Special tools are required to remove and install bearings, seals, and retaining rings. Marks must be made to ensure pistons and other parts are reinstalled in the original positions.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 8SR
Configuration: 330B & 330B L TRACK-TYPE EXCAVATORS 8SR00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00921540
Compression Brake - Remove
SMCS - 1119-011
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00471009
1/2(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. 1. Remove four bolts (1). Disconnect wires (2) and (3) .
Illustration 2 g00471010
2. Remove Compression Brake (A) by lifting Compression Brake (A) with one hand. Remove
Compression Brake (A) while you hold oil tube (4) in order to ensure that oil tube (4) does
not come out of Compression Brake (B) .
3. Remove Compression Brake (B) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 4 20:58:25 UTC+0800 2020
2/2(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 8SR
Configuration: 330B & 330B L TRACK-TYPE EXCAVATORS 8SR00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00921740
Compression Brake - Disassemble
SMCS - 1119-015
Disassembly Procedure
Start By:
A. Remove the Compression Brake. Refer to Disassembly and Assembly, "Compression Brake
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00471083
1/3(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. 1. Remove oil tubes (1) and (2). Remove the O-ring seals.
Note: If the O-ring seals are worn or damaged, use new parts for replacement.
Illustration 2 g00471084
2. Remove snap ring (7), cup (6), spacer (5), springs (4) and (3) and piston (8) .
Illustration 3 g00471085
3. Remove three retaining rings (13). Remove clip (12), springs (11) and (10) and piston (9)
from three locations on the Compression Brake.
2/3(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 4 g00471086
4. Remove three bolts (15), washers (16), clips (17) and piston (14) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 4 20:59:21 UTC+0800 2020
3/3(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 8SR
Configuration: 330B & 330B L TRACK-TYPE EXCAVATORS 8SR00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00921835
Compression Brake - Assemble
SMCS - 1119-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00471086
1. Install piston (14), clips (17), washers (16) and three bolts (15) .
1/3(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 2 g00471085
2. Install piston (9), springs (10) and (11) and clip (12) on three locations on the Compression
Brake. Install three retaining rings (13) .
Illustration 3 g00471084
3. Install piston (8), springs (3) and (4), spacer (5), cup (6) and snap ring (7) .
Illustration 4 g00471083
2/3(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Note: If the O-ring seals are worn or damaged, use new parts for replacement.
4. Install the O-ring seals. Install oil tubes (1) and (2) .
End By: Install the Compression Brake. Refer to Disassembly and Assembly, "Compression
Brake - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 4 21:00:16 UTC+0800 2020
3/3(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 8SR
Configuration: 330B & 330B L TRACK-TYPE EXCAVATORS 8SR00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00921612
Compression Brake - Install
SMCS - 1119-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00471010
1. Install Compression Brake (B) and oil tube (4) .
2. Install Compression Brake (A) .
1/2(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 2 g00471009
3. Connect wires (3) and (2). Install four bolts (1) .
End By: Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 4 21:01:12 UTC+0800 2020
2/2(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 8SR
Configuration: 330B & 330B L TRACK-TYPE EXCAVATORS 8SR00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00999978
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00539802
1/2(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. 1. Remove six bolts (3) and rocker shaft assembly (2). Remove the O-ring seal from the rear
rocker shaft support.
2. Put identification marks on pushrods (1) in order to identify the location of the pushrods in
the engine. Remove pushrods (1) from the engine. Repeat this process for each pushrod.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 4 21:02:08 UTC+0800 2020
2/2(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 8SR
Configuration: 330B & 330B L TRACK-TYPE EXCAVATORS 8SR00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01001004
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Start By:
A. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00490026
1/3(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. 1. Remove O-ring seal (1) from the rear support bracket.
Note: Replace the O-ring seal when the head bolt is removed from the rear rocker shaft
support.
Illustration 2 g00490027
2. Remove retainer ring (6), washer (5), spring (4), washer (3) and rocker arm (2). Note the
number of washers (3) that are used at both ends of the shaft. Remove rocker arms (2) from
each end of the rocker shaft.
Illustration 3 g00449687
3. Remove the pin from the rear rocker shaft support (7) with a hammer and a suitable punch.
Remove rear rocker shaft support (7) .
4. Remove the remaining rocker arms, springs, washers and rocker shaft supports.
5. Remove the plugs from each end of the shaft, if necessary.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Sun Oct 4 21:03:04 UTC+0800 2020
2/3(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 8SR
Configuration: 330B & 330B L TRACK-TYPE EXCAVATORS 8SR00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01138110
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 1 g00449863
1. Install rocker arms (4), supports (1), washer (5) and springs (2) on the rocker shaft.
2. Install rear rocker shaft support (6) on the rocker shaft. Ensure that the hole in the rear
rocker shaft support is aligned with the hole in the rocker shaft.
3. Install pin (3) through the rocker shaft support and the rocker shaft with a hammer.
4. Pin (3) must extend 9.60 mm (.378 inch) above the rocker shaft support.
Illustration 2 g00449625
2/3(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 3 g00449628
5. Install O-ring seal (7). Install rocker arm (4), washer (8), springs (9), washer (10) and
retainer ring (11) .
Note: Make sure that the correct number of washers (8) are installed on the shaft.
6. Install the plugs in each end of the rocker shaft if the plugs were removed.
End By: Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrods - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 4 21:03:59 UTC+0800 2020
3/3(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 8SR
Configuration: 330B & 330B L TRACK-TYPE EXCAVATORS 8SR00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07085956
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00539829
1. Loosen adjusting screws (3). This will prevent a bent valve or a bent pushrod during the
installation of the rocker shaft assembly. Install pushrods (2) and ensure that the pushrods
are seated in the valve lifters.
1/3(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 2. Install rocker shaft assembly (1) in position on the cylinder head.
NOTICE
Ensure that the dowels on each end of the rocker shaft assembly are in
alignment with the holes in the cylinder head.
Illustration 2 g00591852
3304B torque sequence
Illustration 3 g00544706
3306B torque sequence
2/3(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Note: Replace the O-ring seal when the bolt toward the rear of the engine is installed in the
rocker shaft support.
3. Apply 6V-4876 Lubricant on the threads of six bolts (4) except for the bolt that passes
through the rear rocker shaft support (bolt (6) in Illustration 3). Install six bolts (4) in the
rocker shaft assembly.
4. Refer to Illustration 3. Tighten six bolts (4) for the rocker shaft, as follows:
a. Tighten all the bolts in the numerical sequence to a torque of 155 N·m (115 lb ft).
b. Tighten all the bolts in the numerical sequence to a torque of 250 ± 17 N·m
(185 ± 13 lb ft).
c. Tighten all the bolts again in the numerical sequence to a final torque of
250 ± 17 N·m (185 ± 13 lb ft).
5. The assembled length of the springs at both ends of the rocker shaft must be 1.50 ± 0.25 mm
(.059 ± .010 inch). Remove the washers or install the washers behind the springs to change
the assembled length of the springs.
6. Adjust the inlet valve lash to 0.38 ± 0.08 mm (.015 ± .003 inch) and adjust the exhaust valve
lash to 0.64 ± 0.08 mm (.025 ± .003 inch). Refer to Testing and Adjusting, "Air Inlet and
Exhaust System" for more information on setting the valve lash. Tighten the locknuts for the
adjusting screws (3) to a torque of 29 ± 7 N·m (21 ± 5 lb ft). Refer to Specifications, "Valve
Rocker Arms and Lifters".
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 4 21:04:55 UTC+0800 2020
3/3(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 8SR
Configuration: 330B & 330B L TRACK-TYPE EXCAVATORS 8SR00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00991114
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
B. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
C. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00505124
1. Loosen hose clamp (2) on the hose that connects the oil cooler to water pump elbow (1) .
Illustration 2 g00505164
2. Remove two bolts (3) that fasten water pump elbow (1) to the cylinder head. Remove two
bolts (4) that fasten water pump elbow (1) to the water pump.
3. Carefully remove water pump elbow (1) and the gaskets from the engine.
2/4(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 3 g00538842
4. Disconnect tube (5) from the inlet manifold.
Illustration 4 g00538845
5. Remove four bolts (6) and remove air inlet pipe (7) .
Illustration 5 g00541454
3/4(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. NOTICE
Do not set the cylinder head on a hard, flat surface. Damage may occur
to the fuel injection nozzle tips.
6. Remove all bolts (8) and (9) that hold the cylinder head to the cylinder block.
Illustration 6 g00505311
7. Attach the proper lifting device in order to remove cylinder head (10) from the engine.
Remove cylinder head (10) from the engine. The weight of cylinder head (10) is
approximately 95 kg (210 lb).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 4 21:05:51 UTC+0800 2020
4/4(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330B EXCAVATOR 8SR
Configuration: 330B & 330B L TRACK-TYPE EXCAVATORS 8SR00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07489822
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: When the cylinder head is removed, a new spacer plate gasket must be installed. Refer to
Disassembly and Assembly, "Spacer Plate - Remove and Install".
1. Ensure that the surface of the cylinder head is clean and dry. Install a new dry cylinder head
gasket onto the cylinder block.
Illustration 1 g00541495
1/5(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
28. 2. Fasten the proper lifting device to cylinder head (1). Put cylinder head (1) in position on the
cylinder block. Remove the lifting device after cylinder head (1) is positioned.
Illustration 2 g00541497
3. Apply clean engine oil to the threads and the washer faces of cylinder head bolts (2) and (3).
Install cylinder head bolts (2) and (3). Tighten the cylinder head bolts finger tight.
Note: Do not tighten the cylinder head bolts at this time.
Illustration 3 g00511493
4. Install pushrods (4). Make sure that the pushrods are installed in the original location and
that the pushrods are seated correctly in the valve lifters.
5. Loosen the adjusting screws on rocker arms (5) for valve clearance. This will prevent a bent
valve or a broken pushrod during installation.
6. Install a new O-ring seal in the rear rocker arm support.
7. Apply clean engine oil to all the rocker shaft bolts except bolt (25). Refer to illustration 5.
8. Put rocker shaft assembly (5) in position on the cylinder head. Make sure that the dowels in
the rocker shaft supports are aligned with the dowel holes in the cylinder head.
9. Ensure that the rocker arms are aligned with the pushrods and install the rocker shaft
mounting bolts. Tighten the rocker shaft mounting bolts finger tight.
2/5(W)
w
2020/10/4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...