The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...jdjkskmikdkmd
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...paws21610697
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...uddksemd8ud
The documents provide instructions for removing and installing various engine components on a 330B L Excavator with a 3306 engine. The steps include removing the cylinder head by first taking off the fuel injection lines. The rocker shaft is then disassembled by removing the rocker arms, springs and supports. The rocker shaft is assembled by installing these parts in the reverse order. Finally, the rocker shaft and pushrods are installed on the cylinder head and the valve lash is adjusted.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...f7djidksmd3e
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual Instant D...yan77xunhao
The documents provide instructions for removing and installing various engine components on a 330B L Excavator with a 3306 engine. The steps include removing the cylinder head by first taking off the fuel injection lines. The rocker shaft is then disassembled by removing the rocker arms, springs and supports. The rocker shaft is assembled by installing these parts in the reverse order. Finally, the rocker shaft and pushrods are installed on the cylinder head and the valve lash is adjusted.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...f8usiedkdmm
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar cat 330 b l excavator (prefix 6dr) service repair manual (6dr0000...udjdkkmdmdm
The documents provide instructions for removing and installing various engine components on a 330B L Excavator with a 3306 engine. The steps include removing the cylinder head by first taking off the fuel injection lines. The rocker shaft is then disassembled by removing the rocker arms, springs and supports. The rocker shaft is assembled by installing these parts in the reverse order. Finally, the rocker shaft and pushrods are installed on the cylinder head and the valve lash is adjusted.
Caterpillar cat 330 b l excavator (prefix 6dr) service repair manual (6dr0000...fikkskkdmmd
The documents provide instructions for removing and installing various engine components on a 330B L Excavator with a 3306 engine. The steps include removing the cylinder head by first taking off the fuel injection lines. The rocker shaft is then disassembled by removing the rocker arms, springs and supports. The rocker shaft is assembled by installing these parts in the reverse order. Finally, the rocker shaft and pushrods are installed on the cylinder head and the valve lash is adjusted.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...jdjkskmikdkmd
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...paws21610697
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...uddksemd8ud
The documents provide instructions for removing and installing various engine components on a 330B L Excavator with a 3306 engine. The steps include removing the cylinder head by first taking off the fuel injection lines. The rocker shaft is then disassembled by removing the rocker arms, springs and supports. The rocker shaft is assembled by installing these parts in the reverse order. Finally, the rocker shaft and pushrods are installed on the cylinder head and the valve lash is adjusted.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...f7djidksmd3e
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual Instant D...yan77xunhao
The documents provide instructions for removing and installing various engine components on a 330B L Excavator with a 3306 engine. The steps include removing the cylinder head by first taking off the fuel injection lines. The rocker shaft is then disassembled by removing the rocker arms, springs and supports. The rocker shaft is assembled by installing these parts in the reverse order. Finally, the rocker shaft and pushrods are installed on the cylinder head and the valve lash is adjusted.
Caterpillar Cat 330B L Excavator (Prefix 6DR) Service Repair Manual (6DR00001...f8usiedkdmm
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar cat 330 b l excavator (prefix 6dr) service repair manual (6dr0000...udjdkkmdmdm
The documents provide instructions for removing and installing various engine components on a 330B L Excavator with a 3306 engine. The steps include removing the cylinder head by first taking off the fuel injection lines. The rocker shaft is then disassembled by removing the rocker arms, springs and supports. The rocker shaft is assembled by installing these parts in the reverse order. Finally, the rocker shaft and pushrods are installed on the cylinder head and the valve lash is adjusted.
Caterpillar cat 330 b l excavator (prefix 6dr) service repair manual (6dr0000...fikkskkdmmd
The documents provide instructions for removing and installing various engine components on a 330B L Excavator with a 3306 engine. The steps include removing the cylinder head by first taking off the fuel injection lines. The rocker shaft is then disassembled by removing the rocker arms, springs and supports. The rocker shaft is assembled by installing these parts in the reverse order. Finally, the rocker shaft and pushrods are installed on the cylinder head and the valve lash is adjusted.
Caterpillar cat 330 b l excavator (prefix 6dr) service repair manual (6dr0000...fjsjekdmmeme
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar cat 330 b l excavator (prefix 6dr) service repair manual (6dr0000...fjskefkemms
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
The document provides instructions for removing and installing components related to the valve train of a Caterpillar 330 excavator engine. It describes removing the rocker shaft and pushrods, disassembling the rocker shaft, assembling the rocker shaft, and installing the rocker shaft and pushrods. Proper cleaning and lubrication of parts is emphasized to prevent premature wear. Torque specifications and sequences are provided for reinstalling components.
The document provides instructions for removing and installing components related to the valve mechanism of a Caterpillar 330 excavator engine, including the rocker shaft, pushrods, and cylinder head. The removal process involves disconnecting related components like fuel lines and the exhaust manifold. Individual parts are then removed in steps, taking care to properly contain fluids and mark components for reinstallation. Torque specifications and sequences are provided for reinstalling parts in the reverse order.
Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM0000...shudun96087
The document provides instructions for removing and installing components related to the valve train of a Caterpillar 330 excavator engine. It describes removing the rocker shaft and pushrods, disassembling the rocker shaft, assembling the rocker shaft, and installing the rocker shaft and pushrods. Proper cleaning and lubrication of parts is emphasized to prevent premature wear. Torque specifications and sequences are provided for reinstalling components.
The document provides instructions for removing and installing components related to the valve train of a Caterpillar 330 excavator engine, including the rocker shaft, pushrods, and cylinder head. The removal procedure describes disconnecting related components like fuel lines and exhaust manifolds. Individual parts are then removed, including the water pump elbow, air inlet pipe, and cylinder head bolts. Proper lifting equipment is recommended for removing the heavy cylinder head. Installation follows the reverse order.
Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM0000...cnp692569
The document provides instructions for removing and installing components related to the valve train of a Caterpillar 330 excavator engine. It describes removing the rocker shaft and pushrods, disassembling the rocker shaft, assembling the rocker shaft, and installing the rocker shaft and pushrods. Proper cleaning and lubrication of parts is emphasized to prevent premature wear. Torque specifications and sequences are provided for reinstalling components.
The document provides instructions for removing and installing components related to the valve train of a Caterpillar 330 excavator engine, including the rocker shaft, pushrods, and cylinder head. The removal process involves disconnecting related components like fuel lines and the exhaust manifold. Individual parts are then removed in steps, taking care to keep parts clean and contain fluids. Installation is generally the reverse of removal.
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual (MGF00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. It describes 40 steps to disassemble the various components of the travel motor including removing seals, springs, pistons, plates, and bearings. It then describes the assembly process in reverse, providing details on cleaning parts and applying lubricant before reinstalling components in the proper order and orientation.
The document provides instructions for removing and installing a piston pump used for hoist and steering functions on a Caterpillar 725C articulated truck. The removal process involves taking off the cab, then disconnecting hydraulic lines and electrical connectors from the pump. Individual components are then removed from the pump housing in reverse order of the installation instructions. Proper safety precautions and cleaning of parts is emphasized during disassembly and reassembly.
The document provides instructions for disassembling and assembling the freewheel stator of a torque converter. It lists 35 steps for disassembly, removing components like bolts, valves, sensors, gears, bearings and seals. It then lists 29 steps for assembly, installing these components in reverse order. Cleanliness is emphasized throughout to prevent dirt from entering components. Various tools are required, including link brackets, eyebolts and retaining ring pliers.
Caterpillar Cat 390F Mobile Hydraulic Excavator (Prefix B37) Service Repair M...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F Hydraulic Excavator. The disassembly procedure involves 40 steps to remove components like the head, relief valves, spools, pistons, and seals. The assembly procedure reverses the disassembly steps and involves installing components in the correct order and orientation, with notes about cleaning, marking, and applying lubricant to parts. Precautions are provided regarding spring-loaded components.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It describes 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then describes 36 steps for reassembly, including installing seals, bearings, pistons, springs and covers. Precise alignment marks are required for accurate reassembly. Cleanliness is critical and tools are needed to remove and install certain parts.
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
Caterpillar Cat 365B L MH EXCAVATOR (Prefix CTY) Service Repair Manual (CTY00...uddksemd8ud
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator. The disassembly procedure involves removing 17 components from the travel motor housing including the head assembly, brake housing, rotating group, barrel assembly, pistons, and bearings. The assembly procedure instructs installing the components in reverse order.
Caterpillar Cat 345C L Mobile Hydraulic Excavator (Prefix M3E) Service Repair...uddksemd8ud
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, and seals. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the correct order. Contamination of hydraulic systems must be avoided during the process.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts. Tools such as an eyebolt, retaining ring pliers, and bearing puller are required to complete the process.
The document provides instructions to remove the rear power take-off (RPTO) from a Caterpillar C9.3 engine. The steps are:
1. Remove the flywheel housing to access the RPTO.
2. Disconnect the drive shaft from the RPTO and remove retaining bolts.
3. Lift the RPTO straight up to remove.
Caterpillar Cat 340F L LRE Excavator (Prefix YBF) Service Repair Manual (YBF0...uddksemd8ud
This document provides the disassembly and assembly procedures for the travel motor on a 340F L LRE excavator. It includes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. The 27 steps to assemble list installing these same components in reverse order and include notes about lubrication, alignment and torque specifications. Required tools are listed for both procedures.
The document provides instructions for disassembling a piston motor (hydraulic fan) with the following key steps:
1. Remove the head and internal components like seals, plates, and bearings.
2. Extract the pistons, retainer, and bearings from the housing.
3. Use specialty tools to remove the retaining ring and springs, allowing removal of the swashplate and shaft.
Proper safety precautions and cleaning of parts is emphasized before disassembly.
More Related Content
Similar to Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM00001 and up).pdf
Caterpillar cat 330 b l excavator (prefix 6dr) service repair manual (6dr0000...fjsjekdmmeme
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
Caterpillar cat 330 b l excavator (prefix 6dr) service repair manual (6dr0000...fjskefkemms
The documents provide instructions for servicing the valve train components of a Caterpillar 3306 engine. The documents describe how to remove and install the rocker shaft and pushrods, disassemble and assemble the rocker shaft, and remove and install the cylinder head. The procedures note to keep parts clean, identify pushrod locations, torque fasteners correctly, and lift the cylinder head carefully due to its weight.
The document provides instructions for removing and installing components related to the valve train of a Caterpillar 330 excavator engine. It describes removing the rocker shaft and pushrods, disassembling the rocker shaft, assembling the rocker shaft, and installing the rocker shaft and pushrods. Proper cleaning and lubrication of parts is emphasized to prevent premature wear. Torque specifications and sequences are provided for reinstalling components.
The document provides instructions for removing and installing components related to the valve mechanism of a Caterpillar 330 excavator engine, including the rocker shaft, pushrods, and cylinder head. The removal process involves disconnecting related components like fuel lines and the exhaust manifold. Individual parts are then removed in steps, taking care to properly contain fluids and mark components for reinstallation. Torque specifications and sequences are provided for reinstalling parts in the reverse order.
Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM0000...shudun96087
The document provides instructions for removing and installing components related to the valve train of a Caterpillar 330 excavator engine. It describes removing the rocker shaft and pushrods, disassembling the rocker shaft, assembling the rocker shaft, and installing the rocker shaft and pushrods. Proper cleaning and lubrication of parts is emphasized to prevent premature wear. Torque specifications and sequences are provided for reinstalling components.
The document provides instructions for removing and installing components related to the valve train of a Caterpillar 330 excavator engine, including the rocker shaft, pushrods, and cylinder head. The removal procedure describes disconnecting related components like fuel lines and exhaust manifolds. Individual parts are then removed, including the water pump elbow, air inlet pipe, and cylinder head bolts. Proper lifting equipment is recommended for removing the heavy cylinder head. Installation follows the reverse order.
Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM0000...cnp692569
The document provides instructions for removing and installing components related to the valve train of a Caterpillar 330 excavator engine. It describes removing the rocker shaft and pushrods, disassembling the rocker shaft, assembling the rocker shaft, and installing the rocker shaft and pushrods. Proper cleaning and lubrication of parts is emphasized to prevent premature wear. Torque specifications and sequences are provided for reinstalling components.
The document provides instructions for removing and installing components related to the valve train of a Caterpillar 330 excavator engine, including the rocker shaft, pushrods, and cylinder head. The removal process involves disconnecting related components like fuel lines and the exhaust manifold. Individual parts are then removed in steps, taking care to keep parts clean and contain fluids. Installation is generally the reverse of removal.
Similar to Caterpillar Cat 330-A L Excavator (Prefix 5YM) Service Repair Manual (5YM00001 and up).pdf (8)
Caterpillar Cat 390F L Excavator (Prefix MGF) Service Repair Manual (MGF00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F L Excavator. It describes 40 steps to disassemble the various components of the travel motor including removing seals, springs, pistons, plates, and bearings. It then describes the assembly process in reverse, providing details on cleaning parts and applying lubricant before reinstalling components in the proper order and orientation.
The document provides instructions for removing and installing a piston pump used for hoist and steering functions on a Caterpillar 725C articulated truck. The removal process involves taking off the cab, then disconnecting hydraulic lines and electrical connectors from the pump. Individual components are then removed from the pump housing in reverse order of the installation instructions. Proper safety precautions and cleaning of parts is emphasized during disassembly and reassembly.
The document provides instructions for disassembling and assembling the freewheel stator of a torque converter. It lists 35 steps for disassembly, removing components like bolts, valves, sensors, gears, bearings and seals. It then lists 29 steps for assembly, installing these components in reverse order. Cleanliness is emphasized throughout to prevent dirt from entering components. Various tools are required, including link brackets, eyebolts and retaining ring pliers.
Caterpillar Cat 390F Mobile Hydraulic Excavator (Prefix B37) Service Repair M...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor on a 390F Hydraulic Excavator. The disassembly procedure involves 40 steps to remove components like the head, relief valves, spools, pistons, and seals. The assembly procedure reverses the disassembly steps and involves installing components in the correct order and orientation, with notes about cleaning, marking, and applying lubricant to parts. Precautions are provided regarding spring-loaded components.
Caterpillar Cat 390F L Excavator (Prefix TYE) Service Repair Manual (TYE00001...uddksemd8ud
This document provides instructions for disassembling and assembling the travel motor of a 390F L Excavator. It describes 40 steps for disassembly, including removing covers, pistons, springs, seals and other components. It then describes 36 steps for reassembly, including installing seals, bearings, pistons, springs and covers. Precise alignment marks are required for accurate reassembly. Cleanliness is critical and tools are needed to remove and install certain parts.
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
Caterpillar Cat 365B L MH EXCAVATOR (Prefix CTY) Service Repair Manual (CTY00...uddksemd8ud
This document provides assembly instructions for a final drive in 29 steps. It lists required tools and parts. Key steps include: installing bearings and seals; determining bearing preload using shims; assembling carrier assemblies with planetary gears; and installing ring gears, covers, and bolts. Proper cleaning, lubrication and torque specifications are noted throughout assembly.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3176C engine. It describes removing components like sensors, tubes, and manifolds. It instructs to clean mating surfaces and inspect for damage. The correct cylinder head gasket must be installed along with new seals. Bolts are tightened in a specific sequence to the proper torques. Removed components are reinstalled in reverse order.
This document provides instructions for disassembling and assembling the travel motor on a 352F excavator. The disassembly procedure involves removing 17 components from the travel motor housing including the head assembly, brake housing, rotating group, barrel assembly, pistons, and bearings. The assembly procedure instructs installing the components in reverse order.
Caterpillar Cat 345C L Mobile Hydraulic Excavator (Prefix M3E) Service Repair...uddksemd8ud
The document provides instructions for disassembling and assembling a travel motor. Key steps include removing the head, brake piston, rotating group, and seals. Components must be cleaned and any worn parts replaced with new ones. Proper identification and orientation of parts is important for correct reassembly, which involves installing seals, spacers, pistons and other components in the correct order. Contamination of hydraulic systems must be avoided during the process.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts. Tools such as an eyebolt, retaining ring pliers, and bearing puller are required to complete the process.
The document provides instructions to remove the rear power take-off (RPTO) from a Caterpillar C9.3 engine. The steps are:
1. Remove the flywheel housing to access the RPTO.
2. Disconnect the drive shaft from the RPTO and remove retaining bolts.
3. Lift the RPTO straight up to remove.
Caterpillar Cat 340F L LRE Excavator (Prefix YBF) Service Repair Manual (YBF0...uddksemd8ud
This document provides the disassembly and assembly procedures for the travel motor on a 340F L LRE excavator. It includes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, seals and bearings. The 27 steps to assemble list installing these same components in reverse order and include notes about lubrication, alignment and torque specifications. Required tools are listed for both procedures.
The document provides instructions for disassembling a piston motor (hydraulic fan) with the following key steps:
1. Remove the head and internal components like seals, plates, and bearings.
2. Extract the pistons, retainer, and bearings from the housing.
3. Use specialty tools to remove the retaining ring and springs, allowing removal of the swashplate and shaft.
Proper safety precautions and cleaning of parts is emphasized before disassembly.
The document provides instructions for removing and installing an engine oil filter base on a 336D LN excavator. It describes:
1) Removing various connectors, seals, valves, and plugs from the engine oil filter base during disassembly.
2) Assembling the engine oil filter base by installing plugs, seals, valves, and connectors in reverse order of removal.
3) Installing the engine oil filter base on the engine using guide studs and bolts, and reconnecting hoses.
The document provides instructions for installing a fuel injection pump on a Caterpillar 330 excavator engine:
1. Install alignment tools and spacers to hold the fuel injection pump and rack in position. Lubricate seals and install the pump, securing it with a bushing.
2. Use a measurement tool to check that the rack has the proper travel of 15.70 mm after installation.
3. Repeat the process to install the remaining fuel injection pumps and reinstall the cover.
The document provides instructions for installing a cylinder head on a Caterpillar 330 excavator engine. It describes:
1. Cleaning the cylinder head and ensuring it is free of contaminants before installation.
2. Attaching the cylinder head to the cylinder block using bolts in the specified tightening sequence and torque.
3. Reinstalling related components like the exhaust manifold, fuel injection lines, and valve train once the cylinder head is secured.
The summary highlights the key steps of cleaning the cylinder head, attaching it to the engine block, and reinstalling additional parts. It is provided in 3 sentences as requested.
Caterpillar Cat 330D N Hydraulic Excavator (Prefix RAS) Service Repair Manual...uddksemd8ud
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It lists required tools and outlines a 15 step procedure for removing the swivel that includes disconnecting hydraulic lines, removing bolts and other fasteners, and using lifting devices. A 7 step procedure is then given for disassembling the swivel once it is removed, which involves cleaning it, positioning it on a repair stand, and separating its outer housing from the rotor using bolts and other tools.
Caterpillar Cat 330D L Hydraulic Excavator (Prefix RAS) Service Repair Manual...uddksemd8ud
The document provides instructions for removing and disassembling the swivel component of a 330D L hydraulic excavator. It begins with preparing the hydraulic system by releasing pressure and applying vacuum. The swivel is then removed by disconnecting hoses, removing bolts and lifting it off. For disassembly, the swivel is cleaned and secured on a repair stand. Bolts, seals and housing components are then removed to separate the rotor from the outside housing.
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C MH excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly in reverse order, providing details on installing components and applying sealant or lubricant.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 5YM
Configuration: 330, 330L Excavators 5YM00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00921612
Compression Brake - Install
SMCS - 1119-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00471010
1. Install Compression Brake (B) and oil tube (4) .
2. Install Compression Brake (A) .
1/2(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Illustration 2 g00471009
3. Connect wires (3) and (2). Install four bolts (1) .
End By: Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 13 10:08:17 UTC+0800 2020
2/2(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 5YM
Configuration: 330, 330L Excavators 5YM00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00999978
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00539802
1/2(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. 1. Remove six bolts (3) and rocker shaft assembly (2). Remove the O-ring seal from the rear
rocker shaft support.
2. Put identification marks on pushrods (1) in order to identify the location of the pushrods in
the engine. Remove pushrods (1) from the engine. Repeat this process for each pushrod.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 13 10:09:13 UTC+0800 2020
2/2(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 5YM
Configuration: 330, 330L Excavators 5YM00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01001004
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Start By:
A. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00490026
1/3(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. 1. Remove O-ring seal (1) from the rear support bracket.
Note: Replace the O-ring seal when the head bolt is removed from the rear rocker shaft
support.
Illustration 2 g00490027
2. Remove retainer ring (6), washer (5), spring (4), washer (3) and rocker arm (2). Note the
number of washers (3) that are used at both ends of the shaft. Remove rocker arms (2) from
each end of the rocker shaft.
Illustration 3 g00449687
3. Remove the pin from the rear rocker shaft support (7) with a hammer and a suitable punch.
Remove rear rocker shaft support (7) .
4. Remove the remaining rocker arms, springs, washers and rocker shaft supports.
5. Remove the plugs from each end of the shaft, if necessary.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Tue Oct 13 10:10:09 UTC+0800 2020
2/3(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 5YM
Configuration: 330, 330L Excavators 5YM00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01138110
Rocker Shaft - Assemble
SMCS - 1102-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 1 g00449863
1. Install rocker arms (4), supports (1), washer (5) and springs (2) on the rocker shaft.
2. Install rear rocker shaft support (6) on the rocker shaft. Ensure that the hole in the rear
rocker shaft support is aligned with the hole in the rocker shaft.
3. Install pin (3) through the rocker shaft support and the rocker shaft with a hammer.
4. Pin (3) must extend 9.60 mm (.378 inch) above the rocker shaft support.
Illustration 2 g00449625
2/3(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Illustration 3 g00449628
5. Install O-ring seal (7). Install rocker arm (4), washer (8), springs (9), washer (10) and
retainer ring (11) .
Note: Make sure that the correct number of washers (8) are installed on the shaft.
6. Install the plugs in each end of the rocker shaft if the plugs were removed.
End By: Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrods - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 13 10:11:04 UTC+0800 2020
3/3(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 5YM
Configuration: 330, 330L Excavators 5YM00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07085956
Rocker Shaft and Pushrod - Install
SMCS - 1102-012; 1208-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00539829
1. Loosen adjusting screws (3). This will prevent a bent valve or a bent pushrod during the
installation of the rocker shaft assembly. Install pushrods (2) and ensure that the pushrods
are seated in the valve lifters.
1/3(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. 2. Install rocker shaft assembly (1) in position on the cylinder head.
NOTICE
Ensure that the dowels on each end of the rocker shaft assembly are in
alignment with the holes in the cylinder head.
Illustration 2 g00591852
3304B torque sequence
Illustration 3 g00544706
3306B torque sequence
2/3(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Note: Replace the O-ring seal when the bolt toward the rear of the engine is installed in the
rocker shaft support.
3. Apply 6V-4876 Lubricant on the threads of six bolts (4) except for the bolt that passes
through the rear rocker shaft support (bolt (6) in Illustration 3). Install six bolts (4) in the
rocker shaft assembly.
4. Refer to Illustration 3. Tighten six bolts (4) for the rocker shaft, as follows:
a. Tighten all the bolts in the numerical sequence to a torque of 155 N·m (115 lb ft).
b. Tighten all the bolts in the numerical sequence to a torque of 250 ± 17 N·m
(185 ± 13 lb ft).
c. Tighten all the bolts again in the numerical sequence to a final torque of
250 ± 17 N·m (185 ± 13 lb ft).
5. The assembled length of the springs at both ends of the rocker shaft must be 1.50 ± 0.25 mm
(.059 ± .010 inch). Remove the washers or install the washers behind the springs to change
the assembled length of the springs.
6. Adjust the inlet valve lash to 0.38 ± 0.08 mm (.015 ± .003 inch) and adjust the exhaust valve
lash to 0.64 ± 0.08 mm (.025 ± .003 inch). Refer to Testing and Adjusting, "Air Inlet and
Exhaust System" for more information on setting the valve lash. Tighten the locknuts for the
adjusting screws (3) to a torque of 29 ± 7 N·m (21 ± 5 lb ft). Refer to Specifications, "Valve
Rocker Arms and Lifters".
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 13 10:12:00 UTC+0800 2020
3/3(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 5YM
Configuration: 330, 330L Excavators 5YM00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00991114
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
B. Remove the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
C. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00505124
1. Loosen hose clamp (2) on the hose that connects the oil cooler to water pump elbow (1) .
Illustration 2 g00505164
2. Remove two bolts (3) that fasten water pump elbow (1) to the cylinder head. Remove two
bolts (4) that fasten water pump elbow (1) to the water pump.
3. Carefully remove water pump elbow (1) and the gaskets from the engine.
2/4(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Illustration 3 g00538842
4. Disconnect tube (5) from the inlet manifold.
Illustration 4 g00538845
5. Remove four bolts (6) and remove air inlet pipe (7) .
Illustration 5 g00541454
3/4(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. NOTICE
Do not set the cylinder head on a hard, flat surface. Damage may occur
to the fuel injection nozzle tips.
6. Remove all bolts (8) and (9) that hold the cylinder head to the cylinder block.
Illustration 6 g00505311
7. Attach the proper lifting device in order to remove cylinder head (10) from the engine.
Remove cylinder head (10) from the engine. The weight of cylinder head (10) is
approximately 95 kg (210 lb).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 13 10:12:56 UTC+0800 2020
4/4(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 5YM
Configuration: 330, 330L Excavators 5YM00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07489822
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: When the cylinder head is removed, a new spacer plate gasket must be installed. Refer to
Disassembly and Assembly, "Spacer Plate - Remove and Install".
1. Ensure that the surface of the cylinder head is clean and dry. Install a new dry cylinder head
gasket onto the cylinder block.
Illustration 1 g00541495
1/5(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. 2. Fasten the proper lifting device to cylinder head (1). Put cylinder head (1) in position on the
cylinder block. Remove the lifting device after cylinder head (1) is positioned.
Illustration 2 g00541497
3. Apply clean engine oil to the threads and the washer faces of cylinder head bolts (2) and (3).
Install cylinder head bolts (2) and (3). Tighten the cylinder head bolts finger tight.
Note: Do not tighten the cylinder head bolts at this time.
Illustration 3 g00511493
4. Install pushrods (4). Make sure that the pushrods are installed in the original location and
that the pushrods are seated correctly in the valve lifters.
5. Loosen the adjusting screws on rocker arms (5) for valve clearance. This will prevent a bent
valve or a broken pushrod during installation.
6. Install a new O-ring seal in the rear rocker arm support.
7. Apply clean engine oil to all the rocker shaft bolts except bolt (25). Refer to illustration 5.
8. Put rocker shaft assembly (5) in position on the cylinder head. Make sure that the dowels in
the rocker shaft supports are aligned with the dowel holes in the cylinder head.
9. Ensure that the rocker arms are aligned with the pushrods and install the rocker shaft
mounting bolts. Tighten the rocker shaft mounting bolts finger tight.
2/5(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Illustration 4 g00602759
3304B torque sequence
10. Tighten the cylinder head bolts by hand, as follows:
a. Tighten all the bolts (1 through 18) in the numerical sequence to a torque of
150 ± 15 N·m (115 ± 12 lb ft).
b. Tighten all the bolts (1 through 18) again in the numerical sequence to a torque of
250 ± 17 N·m (185 ± 13 lb ft).
c. Tighten all the bolts (1 through 18) again in the numerical sequence to a final torque
of 250 ± 17 N·m (185 ± 13 lb ft).
d. Tighten all the remaining bolts (A through E) to a torque of 43 ± 7 N·m (32 ± 5 lb ft).
3/5(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Illustration 5 g00328807
3306B torque sequence
11. Tighten the cylinder head bolts by hand, as follows:
a. Tighten all the bolts (1 through 26) in the numerical sequence to a torque of
150 ± 15 N·m (115 ± 12 lb ft).
b. Tighten all the bolts (1 through 26) in the numerical sequence to a torque of
250 ± 17 N·m (185 ± 13 lb ft).
c. Tighten all the bolts (1 through 26) again in the numerical sequence to a final torque
of 250 ± 17 N·m (185 ± 13 lb ft).
d. Tighten all the remaining bolts (A through G) to a torque of 43 ± 7 N·m (32 ± 5 lb ft).
12. Adjust the inlet valve lash to 0.38 mm (.015 inch) and the exhaust valve lash to 0.64 mm
(.025 inch). Tighten the locknuts for the adjusting screws to a torque of 29 ± 7 N·m
(22 ± 5 lb ft). Refer to the Testing and Adjusting, "Air Inlet and Exhaust System" topic for
additional information on valve lash adjustments.
Illustration 6 g00511911
13. Put the gasket and air inlet pipe (7) in position on the cylinder head. Install four bolts (6) to
fasten air inlet pipe (7) to the cylinder head.
Illustration 7 g00541522
4/5(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. 14. Connect tube (8) to the inlet manifold.
Illustration 8 g00541524
15. Put the gaskets and water pump elbow (11) in position on the engine. Install two bolts (9)
that fasten water pump elbow (11) to the cylinder head. Install two bolts (10) that fasten
water pump elbow (11) to the water pump.
Illustration 9 g00541527
16. Tighten hose clamp (12).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
b. Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold -
Remove and Install".
c. Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 13 10:13:52 UTC+0800 2020
5/5(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330-A L EXCAVATOR 5YM
Configuration: 330, 330L Excavators 5YM00001-UP (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01045029
Spacer Plate - Remove and Install
SMCS - 1221-010
Removal Procedure
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00540847
1/4(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
25. 1. Remove O-ring seal (1), water seals (3) and water directors (4) from spacer plate (2) .
Illustration 2 g00540857
NOTICE
Do not damage the dowels as the spacer plate is removed.
2. Remove spacer plate (2) from the cylinder head.
Illustration 3 g00540895
3. Remove O-ring seal (6) and spacer plate gasket (5) from the cylinder head.
Installation Procedure
2/4(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
26. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean the mating surfaces between the spacer plate and the cylinder block.
Illustration 4 g00540895
2. Install new spacer plate gasket (5) and new O-ring seal (6) .
Note: If the dowels in the cylinder block have been removed for any reason, the overall
height of the installation is 16.0 ± 5.0 mm (.63 ± .20 inch).
Illustration 5 g00540857
Note: Both surfaces of the spacer plate, spacer plate gasket and the top of the cylinder block
must be clean and dry. Do not use any gasket adhesive or other substances on these
surfaces.
3/4(W)
w
2020/10/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...