The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a Caterpillar 330 LN excavator engine. The procedures describe using various specialty tools to compress springs, remove and insert parts, and ensure proper dimensions. Safety notices emphasize keeping parts clean and containing fluids to prevent damage and injury.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 325 c excavator (prefix blx) service repair manual (blx00001 ...fjsekkdmme
This document provides instructions for removing and installing engine components on a 325C excavator, including:
- Inlet and exhaust valves, using valve spring compressors and other tools.
- Inlet and exhaust valve guides, using driver tools.
- Inlet and exhaust valve seat inserts, using extractor tools and an installer tool.
- The engine oil filter base, using a strap wrench.
Detailed steps are given for each procedure, including required tools and safety notices.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
Caterpillar cat d400 e ii ejector truck (prefix apf) service repair manual (a...fjsqazkekdmme
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a D400E II Ejector Truck. It describes the required tools and safety precautions for each step. The procedure involves compressing springs, removing retainers, lubricating parts, and ensuring proper heights and locations are achieved during installation. A second section provides instructions for disassembling the engine oil filter base to access internal valves and springs.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 325 c excavator (prefix s2c) service repair manual (s2c00001 ...fjsekkdmme
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 325C excavator with a 3126 engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and ensuring parts are clean. Safety notices are included to warn of potential injury from parts propelled by springs.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...fkjsekksmem
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
Caterpillar cat 330 track type excavator (prefix 6 sk) service repair manual ...fjskefkemms
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, valve seat inserts, and the engine oil filter base on a 330L excavator. The procedures include using various tools to compress springs, extract components, and install new parts. Technicians are advised to keep components clean and replace seals and gaskets as needed.
Caterpillar cat 325 c excavator (prefix blx) service repair manual (blx00001 ...fjsekkdmme
This document provides instructions for removing and installing engine components on a 325C excavator, including:
- Inlet and exhaust valves, using valve spring compressors and other tools.
- Inlet and exhaust valve guides, using driver tools.
- Inlet and exhaust valve seat inserts, using extractor tools and an installer tool.
- The engine oil filter base, using a strap wrench.
Detailed steps are given for each procedure, including required tools and safety notices.
The document provides instructions for installing an engine oil filter base which includes:
1. Lubricating the O-rings and installing them on the engine oil filter base.
2. Positioning the engine oil filter base and installing bolts to secure it.
3. Reconnecting any disconnected tubes.
The instructions are intended for technicians and include safety warnings for containing fluids and wearing protective equipment.
Caterpillar cat d400 e ii ejector truck (prefix apf) service repair manual (a...fjsqazkekdmme
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a D400E II Ejector Truck. It describes the required tools and safety precautions for each step. The procedure involves compressing springs, removing retainers, lubricating parts, and ensuring proper heights and locations are achieved during installation. A second section provides instructions for disassembling the engine oil filter base to access internal valves and springs.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 325 c excavator (prefix s2c) service repair manual (s2c00001 ...fjsekkdmme
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 325C excavator with a 3126 engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and ensuring parts are clean. Safety notices are included to warn of potential injury from parts propelled by springs.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...fkjsekksmem
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
This document is a service manual for MerCruiser #26 GM 4-cylinder 181 cid (3.0L) marine engines. It provides information and procedures for technicians to service these engines, including removal/installation, mechanical systems, electrical systems, fuel systems, cooling systems, exhaust systems and power steering. The manual outlines safety warnings and identifies the models covered. It also provides general information to help technicians such as how to use the manual, read parts manuals, understand directional references and engine rotation.
Mercury mercruiser marine engines #28 bravo sterndrives service repair manualcdfzxs
This document is the service manual for MerCruiser #28 Bravo Sterndrives. It provides information on maintenance, troubleshooting, removal and installation procedures. The manual begins with important safety notices and outlines the document structure. Subsequent sections cover lubrication and maintenance schedules, troubleshooting common issues, and detailed removal and installation instructions for sterndrive components. Torque specifications, tool requirements and other technical details are included to aid mechanics in properly servicing these sterndrives.
This document is the service manual for MerCruiser #24 GM V-8 305 CID (5.0L) / 350 CID (5.7L) marine engines. The manual contains sections on important information, removal and installation, the engine, electrical systems, fuel systems, cooling systems, exhaust systems, drives, power steering systems, and troubleshooting. It provides information and instructions for mechanics to service these MerCruiser engines.
Komatsu sk510 5 skid steer loader service repair manual (sn 37 df00001 and up)cdfzxs
This document is a shop manual for the SK510-5 skid-steer loader. It provides information on structure and function, testing and adjusting procedures, disassembly and assembly instructions, and maintenance standards. The manual contains safety precautions that must be followed when working on the loader. It explains how to properly lift heavy components using hoists or cranes. Standard tightening torques are also provided for bolts, nuts, and other fasteners.
Komatsu d63 e 12 dozer bulldozer service repair manual (sn 2001 and up)cdfzxs
1) The document is a shop manual that provides instructions for servicing and repairing a Bulldozer model D63E-12 from serial numbers 2001 and up.
2) It consists of several sections that cover specifications, structure and maintenance standards, testing and adjustments, troubleshooting, and disassembly/assembly of components.
3) The sections are further divided into topics that each have a form number identifying individual documents covering specific components and systems.
Komatsu ck25 1 skid steer loader service repair manual (sn f00003 and up)cdfzxs
This document provides safety information and instructions for servicing a CK25-1 crawler skid-steer loader. It discusses general safety precautions, preparations for work, precautions during work, and hoisting instructions. Safety symbols are defined that mark important safety points in the manual. The document instructs technicians to carefully follow all safety cautions, prepare the work area and equipment properly before starting repairs, and use lifting equipment correctly when hoisting components.
Daewoo doosan de12 tis diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining Daewoo DE series diesel engines, including the DE12, DE12T, DE12TI, and DE12TIS models. It describes the engine components and specifications. The manual includes symbols to indicate maintenance tasks and instructions for proper disposal of waste. It aims to help customers and distributors maintain engines in optimum condition through correct operation and proper maintenance.
Daewoo doosan de12 ti diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration, replacing the fan belt if damaged, and checking the engine oil level is important to maintain optimum engine performance and durability. The manual explains maintenance procedures and contains symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo doosan de12 t diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining Daewoo DE series diesel engines, including the DE12, DE12T, DE12TI, and DE12TIS models. It describes the key features of the engines such as their OMEGA combustion bowl design and specifications including power, torque, and idle speeds. Exploded diagrams show the main engine components and assemblies in the various models. The manual instructs technicians on general repair procedures and identifies symbols used to indicate different service operations.
Daewoo doosan de12 diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Crown ws2000 series forklift service repair manualcdfzxs
This document is a service and parts manual for a series of trucks. It contains sections on maintenance, lubrication, hydraulic systems, drive units, electrical systems, and components. The manual provides instructions for inspection, maintenance, repair, and replacement of parts. It includes diagrams of hydraulic and electrical systems, lists of lubrication points, and torque specifications for fasteners.
Crown wp2300 s series pallet truck service repair manualcdfzxs
This document provides revisions and maintenance information for the WP2300S Series order number 812529-006. It includes:
- Revisions made to various pages and components, including additions and corrections to safety switches, platform control switches, and platform logic circuits.
- Sections covering maintenance procedures such as lubrication and adjustments, hydraulics, electrical components, brakes, steering and other systems.
- Electrical diagrams for standard and optional configurations of folded and fixed platforms.
Crown wp2300 series pallet truck service repair manualcdfzxs
The document provides an overview of maintenance and repair for a WP2300 series truck. It includes sections on lubrication and adjustment, hydraulics, drive unit, electrics, brakes, steering, lifting mechanism, cylinders, electrical diagrams and hydraulic schematics. Safety symbols and notes are defined. Only authorized personnel should perform maintenance following the procedures in this manual. Replacement parts must be original equipment.
Crown wp2000 s series pallet truck service repair manualcdfzxs
This document is a service manual that provides maintenance and repair instructions for a WP2000S series truck. It contains sections on safety, introduction, lubrication and adjustment, hydraulics, drive unit, electrics, brakes, steering, lifting mechanism, cylinders, electrical diagrams, and hydraulic schematics. The introduction section notes that the manual should be used by trained personnel, and covers operating instructions, service training, replacement parts orders, and the structure and numbering of the manual pages.
This document provides instructions for disassembling a travel motor from an excavator model 326D2 L. The 27 step procedure includes removing the head, brake piston, plates, and friction discs. Special tools are required to remove components like the rotating assembly, bearing races, and retaining rings. Technicians are advised to mark components like the pistons and barrel assembly to ensure correct reassembly.
The document provides instructions for disassembling a travel motor. It begins by having the technician remove the travel motor from the excavator and clean the outside. The technician is then instructed to fasten the motor vertically and mark it for alignment before disassembling. The summary proceeds to list the 27 steps to disassemble the various components of the travel motor, including removing the head, brake piston, barrel assembly, and shaft assembly. Tools required for the disassembly are also provided in a table.
The document provides instructions for disassembling a travel motor from an excavator. It describes 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, springs, seals, and other internal parts. Precautions are provided to watch for spring forces and use lifting devices due to the weight of some components. Detailed illustrations accompany each step.
Caterpillar cat 325 d mh excavator (prefix rjk) service repair manual (rjk000...cdfzxs
The document provides instructions for disassembling and assembling the travel motor of a 325D MH Excavator. It lists 28 steps for disassembly, requiring various tools to remove components like the head, port plate, springs, brake piston, plates, and seals. It then lists 23 steps for assembly, applying thread lock compound and ensuring proper installation of keys, cam plate, friction discs, backup rings, seals, and brake piston. Cleanliness is stressed and O-rings must be replaced.
Caterpillar cat 325 d mh excavator (prefix c4h) service repair manual (c4h000...cdfzxs
This document provides instructions to disassemble a final drive on a 325D MH EXCAVATOR. It outlines 31 steps to remove components like the cover, gears, carrier assemblies, housing and seals. Special tools are required and cleanliness is important to prevent dirt from entering during reassembly. The procedure includes notes on alignment marks, weights of parts, and disassembling planetary gears within carrier assemblies.
Caterpillar cat 325 c excavator (prefix s2c) service repair manual (s2c00001 ...cdfzxs
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and tapping guides into place. Safety notices warn of potential injury from parts propelled by springs and ensure clean parts to prevent premature wear.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
This document is a service manual for MerCruiser #26 GM 4-cylinder 181 cid (3.0L) marine engines. It provides information and procedures for technicians to service these engines, including removal/installation, mechanical systems, electrical systems, fuel systems, cooling systems, exhaust systems and power steering. The manual outlines safety warnings and identifies the models covered. It also provides general information to help technicians such as how to use the manual, read parts manuals, understand directional references and engine rotation.
Mercury mercruiser marine engines #28 bravo sterndrives service repair manualcdfzxs
This document is the service manual for MerCruiser #28 Bravo Sterndrives. It provides information on maintenance, troubleshooting, removal and installation procedures. The manual begins with important safety notices and outlines the document structure. Subsequent sections cover lubrication and maintenance schedules, troubleshooting common issues, and detailed removal and installation instructions for sterndrive components. Torque specifications, tool requirements and other technical details are included to aid mechanics in properly servicing these sterndrives.
This document is the service manual for MerCruiser #24 GM V-8 305 CID (5.0L) / 350 CID (5.7L) marine engines. The manual contains sections on important information, removal and installation, the engine, electrical systems, fuel systems, cooling systems, exhaust systems, drives, power steering systems, and troubleshooting. It provides information and instructions for mechanics to service these MerCruiser engines.
Komatsu sk510 5 skid steer loader service repair manual (sn 37 df00001 and up)cdfzxs
This document is a shop manual for the SK510-5 skid-steer loader. It provides information on structure and function, testing and adjusting procedures, disassembly and assembly instructions, and maintenance standards. The manual contains safety precautions that must be followed when working on the loader. It explains how to properly lift heavy components using hoists or cranes. Standard tightening torques are also provided for bolts, nuts, and other fasteners.
Komatsu d63 e 12 dozer bulldozer service repair manual (sn 2001 and up)cdfzxs
1) The document is a shop manual that provides instructions for servicing and repairing a Bulldozer model D63E-12 from serial numbers 2001 and up.
2) It consists of several sections that cover specifications, structure and maintenance standards, testing and adjustments, troubleshooting, and disassembly/assembly of components.
3) The sections are further divided into topics that each have a form number identifying individual documents covering specific components and systems.
Komatsu ck25 1 skid steer loader service repair manual (sn f00003 and up)cdfzxs
This document provides safety information and instructions for servicing a CK25-1 crawler skid-steer loader. It discusses general safety precautions, preparations for work, precautions during work, and hoisting instructions. Safety symbols are defined that mark important safety points in the manual. The document instructs technicians to carefully follow all safety cautions, prepare the work area and equipment properly before starting repairs, and use lifting equipment correctly when hoisting components.
Daewoo doosan de12 tis diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining Daewoo DE series diesel engines, including the DE12, DE12T, DE12TI, and DE12TIS models. It describes the engine components and specifications. The manual includes symbols to indicate maintenance tasks and instructions for proper disposal of waste. It aims to help customers and distributors maintain engines in optimum condition through correct operation and proper maintenance.
Daewoo doosan de12 ti diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration, replacing the fan belt if damaged, and checking the engine oil level is important to maintain optimum engine performance and durability. The manual explains maintenance procedures and contains symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo doosan de12 t diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining Daewoo DE series diesel engines, including the DE12, DE12T, DE12TI, and DE12TIS models. It describes the key features of the engines such as their OMEGA combustion bowl design and specifications including power, torque, and idle speeds. Exploded diagrams show the main engine components and assemblies in the various models. The manual instructs technicians on general repair procedures and identifies symbols used to indicate different service operations.
Daewoo doosan de12 diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Crown ws2000 series forklift service repair manualcdfzxs
This document is a service and parts manual for a series of trucks. It contains sections on maintenance, lubrication, hydraulic systems, drive units, electrical systems, and components. The manual provides instructions for inspection, maintenance, repair, and replacement of parts. It includes diagrams of hydraulic and electrical systems, lists of lubrication points, and torque specifications for fasteners.
Crown wp2300 s series pallet truck service repair manualcdfzxs
This document provides revisions and maintenance information for the WP2300S Series order number 812529-006. It includes:
- Revisions made to various pages and components, including additions and corrections to safety switches, platform control switches, and platform logic circuits.
- Sections covering maintenance procedures such as lubrication and adjustments, hydraulics, electrical components, brakes, steering and other systems.
- Electrical diagrams for standard and optional configurations of folded and fixed platforms.
Crown wp2300 series pallet truck service repair manualcdfzxs
The document provides an overview of maintenance and repair for a WP2300 series truck. It includes sections on lubrication and adjustment, hydraulics, drive unit, electrics, brakes, steering, lifting mechanism, cylinders, electrical diagrams and hydraulic schematics. Safety symbols and notes are defined. Only authorized personnel should perform maintenance following the procedures in this manual. Replacement parts must be original equipment.
Crown wp2000 s series pallet truck service repair manualcdfzxs
This document is a service manual that provides maintenance and repair instructions for a WP2000S series truck. It contains sections on safety, introduction, lubrication and adjustment, hydraulics, drive unit, electrics, brakes, steering, lifting mechanism, cylinders, electrical diagrams, and hydraulic schematics. The introduction section notes that the manual should be used by trained personnel, and covers operating instructions, service training, replacement parts orders, and the structure and numbering of the manual pages.
This document provides instructions for disassembling a travel motor from an excavator model 326D2 L. The 27 step procedure includes removing the head, brake piston, plates, and friction discs. Special tools are required to remove components like the rotating assembly, bearing races, and retaining rings. Technicians are advised to mark components like the pistons and barrel assembly to ensure correct reassembly.
The document provides instructions for disassembling a travel motor. It begins by having the technician remove the travel motor from the excavator and clean the outside. The technician is then instructed to fasten the motor vertically and mark it for alignment before disassembling. The summary proceeds to list the 27 steps to disassemble the various components of the travel motor, including removing the head, brake piston, barrel assembly, and shaft assembly. Tools required for the disassembly are also provided in a table.
The document provides instructions for disassembling a travel motor from an excavator. It describes 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, springs, seals, and other internal parts. Precautions are provided to watch for spring forces and use lifting devices due to the weight of some components. Detailed illustrations accompany each step.
Caterpillar cat 325 d mh excavator (prefix rjk) service repair manual (rjk000...cdfzxs
The document provides instructions for disassembling and assembling the travel motor of a 325D MH Excavator. It lists 28 steps for disassembly, requiring various tools to remove components like the head, port plate, springs, brake piston, plates, and seals. It then lists 23 steps for assembly, applying thread lock compound and ensuring proper installation of keys, cam plate, friction discs, backup rings, seals, and brake piston. Cleanliness is stressed and O-rings must be replaced.
Caterpillar cat 325 d mh excavator (prefix c4h) service repair manual (c4h000...cdfzxs
This document provides instructions to disassemble a final drive on a 325D MH EXCAVATOR. It outlines 31 steps to remove components like the cover, gears, carrier assemblies, housing and seals. Special tools are required and cleanliness is important to prevent dirt from entering during reassembly. The procedure includes notes on alignment marks, weights of parts, and disassembling planetary gears within carrier assemblies.
Caterpillar cat 325 c excavator (prefix s2c) service repair manual (s2c00001 ...cdfzxs
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and tapping guides into place. Safety notices warn of potential injury from parts propelled by springs and ensure clean parts to prevent premature wear.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa Warheit
Caterpillar cat 330 l excavator (prefix 8 ck) service repair manual (8ck00001 and up)
1. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 LN EXCAVATOR 8CK
Configuration: 330, 330 L AND 330 LN EXCAVATORS 8CK00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00962627
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
B 8S-2263 Valve Spring Tester 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and assembly, "Cylinder Head - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
2. Illustration 1 g00490614
1. Use Tool (A) to compress valve spring (2) and remove valve keepers (1) .
2. Remove Tool (A), the rotocoil, the valve spring and the valve stem oil shield. Remove the
valve from the cylinder head. Put identification marks on the valves for installation
purposes.
Illustration 2 g00490682
3. Check the valve spring force with Tool (B). Refer to Specifications, "Cylinder Head
Valves" for information on the valve springs.
4. Perform Steps 1 through 3 for the remaining inlet and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
B 5S-1322 Valve Keeper Inserter 1
2/4(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Lubricate the inlet and exhaust valves with clean engine oil. Install the inlet and exhaust
valves in the original location in the cylinder head.
Illustration 3 g00508681
2. Install valves (3), oil shield (4), valve spring (2) and rotocoil (1) in the cylinder head.
Illustration 4 g00490777
3. Use Tool (A) to compress valve spring (2). Install valve keeper (5) on the valve stem with
Tool (B) .
3/4(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
4. Carefully remove Tool (A). Strike the top of the valve with a soft faced hammer in order to
ensure that the valve keepers are properly installed.
5. Repeat Steps 3 through 4 for the remaining inlet and exhaust valves.
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove
and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 18 18:08:03 UTC+0800 2020
4/4(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 LN EXCAVATOR 8CK
Configuration: 330, 330 L AND 330 LN EXCAVATORS 8CK00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00962891
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7349 Valve Guide Driver 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. Illustration 1 g00490787
1. Use Tool (A) to remove the inlet and exhaust valve guides from the cylinder head.
2. Repeat Step 1 for the remaining inlet and exhaust valve guides.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 9U-7349 Valve Guide Driver 1
B 9U-6954 Valve Guide Collar 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Illustration 2 g00490790
1. Put clean engine oil on the outside diameter of the valve guide. Install the valve guide with
Tool (A) and Tool (B), as shown.
Illustration 3 g00508601
2. Dimension (X) from the top of the valve guide to the cylinder head must be 22.23 ± 0.25
mm (0.875 ± 0.010 inch). For more information on the inlet and exhaust valve guides, refer
to Specifications, "Cylinder Head Valves".
Note: In order to help prevent damage to the valve guides, Tool (B) must be used during
installation.
3. Repeat Steps 1 and 2 for the remaining inlet and exhaust valve guides.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 18 18:08:59 UTC+0800 2020
3/3(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 LN EXCAVATOR 8CK
Configuration: 330, 330 L AND 330 LN EXCAVATORS 8CK00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i02107684
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4805 Valve Seat Extractor Tool Group 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 1 g00490857
1. Use Tooling (A) in order to remove the valve seat insert from the cylinder head.
2. Clean the valve seat in the cylinder head. Remove any rough areas from the valve seat in the
cylinder head.
3. Repeat Steps 1 and 2 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 6V-4805 Valve Seat Extractor Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Illustration 2 g00508515
1. Shrink the new valve insert with reduced temperature. Use Tooling (A) in order to install
the new valve seat insert in the cylinder head.
Note: Do not increase the diameter of the extractor in the valve seat insert when the insert is
installed in the cylinder head.
2. Repeat Step 1 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 18 18:09:55 UTC+0800 2020
3/3(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 LN EXCAVATOR 8CK
Configuration: 330, 330 L AND 330 LN EXCAVATORS 8CK00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00981264
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8250 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
1/3(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00499430
1. Remove the oil filter from engine oil filter base (1) with Tool (A).
Illustration 2 g00499568
2. Remove bolts (5), tube assembly (3) and the gasket. Remove the O-ring seal in tube
assembly (3) and replace the O-ring seal, if necessary.
3. Remove the bolts that hold tube assembly (4) to the cylinder block. Remove tube assembly
(4) and the gasket. Remove the O-ring seal in tube assembly (4) and replace the O-ring seal,
if necessary.
4. Remove four bolts (2) and engine oil filter base (1) from the cylinder block. Remove the O-
ring seals from engine oil filter base (1), if necessary.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 18 18:10:51 UTC+0800 2020
2/3(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 LN EXCAVATOR 8CK
Configuration: 330, 330 L AND 330 LN EXCAVATORS 8CK00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00983225
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
A. Remove the engine oil filter and the engine oil filter base. Refer to Disassembly and
Assembly, "Engine Oil Filter Base - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00500551
1/2(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Typical Example
Illustration 2 g00500559
Typical Example
1. Remove O-ring seals (1) from the engine oil filter base. Remove four bolts (2), two covers
(3) and two gaskets (6) .
Note: Plunger (4) is for the oil filter bypass. Plunger (7) is for the engine oil cooler bypass.
2. Remove springs (5), plunger (4) and plunger (7) from the engine oil filter base.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 18 18:11:46 UTC+0800 2020
2/2(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 LN EXCAVATOR 8CK
Configuration: 330, 330 L AND 330 LN EXCAVATORS 8CK00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00983561
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00500559
1/2(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Illustration 2 g00500551
1. Install plunger (7), plunger (4) and springs (5) .
Note: Plunger (7) is for the engine oil cooler bypass. Plunger (4) is for the oil filter bypass.
Note: Check the condition of the O-ring seals and gaskets. If the seals or gaskets are worn
or damaged, use new parts for replacement.
2. Install two gaskets (6), two covers (3), four bolts (2) and O-ring seals (1) .
End By: Install the engine oil filter base and the oil filter. Refer to Disassembly and Assembly,
"Engine Oil Filter Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 18 18:12:42 UTC+0800 2020
2/2(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 LN EXCAVATOR 8CK
Configuration: 330, 330 L AND 330 LN EXCAVATORS 8CK00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00981970
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8250 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Check the condition of the O-ring seals and the gaskets. If the seals or the gaskets are worn
or damaged, use new parts for replacement.
1/2(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Illustration 1 g00499568
Note: Coat all of the O-ring seals with clean engine oil prior to installation.
2. Put the O-ring seals on engine oil filter base (1). Install engine oil filter base (1) on the
cylinder block with four bolts (2) .
3. Put the O-ring seal and the gasket in position on tube assembly (4). Install tube assembly (4)
on the cylinder block. Install the bolts that hold tube assembly (4) in position.
4. Put the O-ring seal and the gasket in position on tube assembly (3). Fasten the clip to tube
assembly (4). Position tube assembly (3) onto the cylinder block and install bolts (5).
Illustration 2 g00499430
5. Install engine oil filter (1) with Tool (A) .
Note: Follow the installation procedure on the engine oil filter in order to install the engine
oil filter on the engine oil filter base.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 18 18:13:38 UTC+0800 2020
2/2(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 LN EXCAVATOR 8CK
Configuration: 330, 330 L AND 330 LN EXCAVATORS 8CK00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01111322
Engine Oil Cooler - Remove
SMCS - 1378-011
3304B Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Illustration 1 g00590134
3304B engine
(1) Remove bolts (4), elbow (5) and the gasket from the engine block.
(2) Remove oil cooler (2) and the gasket.
(3) If necessary, loosen clamp (1), and remove pipe (7) from the engine.
3306B Removal Procedure
Start By:
A. Remove the engine oil filter and the engine oil filter base. Refer to Disassembly and
Assembly, "Engine Oil Filter Base - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
2/3(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. Dispose of all fluids according to local regulations and mandates.
Illustration 2 g00468427
1. Loosen two hose clamps (1) .
Illustration 3 g00468428
2. Disconnect hose assembly (5). Disconnect clip (3) for the engine oil level gauge. Remove
three bolts (4) and remove engine oil cooler (2).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 18 18:14:34 UTC+0800 2020
3/3(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330 LN EXCAVATOR 8CK
Configuration: 330, 330 L AND 330 LN EXCAVATORS 8CK00001-UP (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00921081
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
A. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00470817
1/2(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
24. 1. Remove pipe (1), two elbows (2) and bonnet (3) from cooler core (4) .
Illustration 2 g00470818
2. Clean the tubes of cooler core (4) with 3.96 mm (.156 inch) rod (5) .
Note: The O-ring seals should be removed and inspected for damage. If the O-ring seals are
worn or damaged, use new parts for replacement.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 18 18:15:29 UTC+0800 2020
2/2(W)
w
2020/10/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...