The document provides instructions for removing and installing a vibration damper and pulley assembly on a Caterpillar C7.1 engine. To remove the assembly, the alternator belt must first be removed. Torx screws are then removed using a socket while the crankshaft is prevented from rotating. The assembly can be disassembled further by removing bolts to separate the damper, pulley, and adapter. Installation follows the removal steps in reverse, including reinstalling bolts and screws while ensuring proper orientation and torque specifications are followed.
Caterpillar cat 330 f excavator (prefix hbt) service repair manual (hbt00001 ...fjskekdmjekm
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, then remove the cover and gasket.
3. Clean the cover, housing, and install a new gasket. Use guide studs to position the cover and hand tighten bolts.
4. Align the cover and tighten the bolts. Install a new front seal. Reinstall the pulley, fan if equipped.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 330 c excavator (prefix rbh) service repair manual (rbh00001 ...hfjsekekmmd
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing all seals and installing components in the reverse order of disassembly.
- Special tools are required for tasks like removing bearings and installing retaining rings.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c l excavator (prefix mca) service repair manual (mca0000...hhjsekmdmm
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Caterpillar cat 330 f excavator (prefix hbt) service repair manual (hbt00001 ...fjskekdmjekm
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, then remove the cover and gasket.
3. Clean the cover, housing, and install a new gasket. Use guide studs to position the cover and hand tighten bolts.
4. Align the cover and tighten the bolts. Install a new front seal. Reinstall the pulley, fan if equipped.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 330 c excavator (prefix rbh) service repair manual (rbh00001 ...hfjsekekmmd
- The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
- It describes 27 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
- It then describes 28 steps for reassembling the travel motor, replacing all seals and installing components in the reverse order of disassembly.
- Special tools are required for tasks like removing bearings and installing retaining rings.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 c l excavator (prefix mca) service repair manual (mca0000...hhjsekmdmm
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Caterpillar cat 349 f excavator (prefix hlb) service repair manual (hlb00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f excavator (prefix bz2) service repair manual (bz200001 ...fjskekxcddmmme
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy. Diagrams illustrate each step for clarification. The goal is to fully disassemble the travel motor into its individual parts for repair or replacement.
Caterpillar cat 349 e l vg excavator (prefix etc) service repair manual (etc0...fjskekxcddmmme
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque is required for all bolts.
Caterpillar cat 349 e l vg excavator (prefix kfx) service repair manual (kfx0...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order. Tools, torque specifications, and component descriptions are provided in tables throughout.
Caterpillar cat 349 e l excavator (prefix whz) service repair manual (whz0000...fjskekxcddmmme
The document provides instructions for disassembling and assembling the final drive of a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...fjskekxcddmmme
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly process reverses the disassembly steps and includes applying sealant and pressing components together using various tools. Cleanliness is emphasized throughout.
Caterpillar cat 349 e l excavator (prefix spg) service repair manual (spg0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 24 steps to remove components like the head assembly, brake housing, barrel assembly, pistons, and bearings. The assembly process reverses this with 13 steps like installing seals, springs, pins and bearings onto components before lowering the rotating group into the motor housing. Precautions and torque specifications are provided for correct reassembly.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar cat 349 e l excavator (prefix mzw) service repair manual (mzw0000...fjskekxcddmmme
This document provides disassembly and assembly instructions for the final drive of a 349E L excavator. It includes specifications for the components, required tools, assembly procedures with illustrations, and torque specifications. The procedures describe cleaning and applying lubricants to parts, measuring clearances, installing bearings and seals, and adjusting shims to set proper spacing before tightening bolts and setscrews to specified torques.
Caterpillar cat 349 e l excavator (prefix mpz) service repair manual (mpz0000...fjskekxcddmmme
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts and lubricant is used where appropriate.
Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section lists 14 steps and specifies torque values and lubricants for reinstalling components in reverse order. Tools, torque specifications, and component descriptions are provided in supporting tables throughout.
Caterpillar cat 349 e l excavator (prefix fjb) service repair manual (fjb0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the hydraulic fan drive on a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 e l excavator (prefix etc) service repair manual (etc0000...fjskekxcddmmme
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque specifications are provided for reinstallation.
Caterpillar cat 349 e excavator (prefix whz) service repair manual (whz00001 ...fjskekxcddmmme
The document provides instructions for disassembling and assembling the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 e excavator (prefix spg) service repair manual (spg00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves removing 27 individual components from the motor housing, rotating group, and brake housing. The assembly process describes installing the components in reverse order and includes specifications for various parts. Proper lubrication and torque specifications are noted throughout.
Caterpillar cat 349 e excavator (prefix rgh) service repair manual (rgh00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 d2 l vg excavator (prefix sdm) service repair manual (sdm...fjskekxcddmmme
The document provides instructions for disassembling and assembling a travel motor. It lists 30 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 31 steps for assembly, reinstalling these components in reverse order. Precautions are given to prevent contamination and ensure proper installation of parts like O-rings, seals, and pins in their original locations. Tools required are listed in a table.
Caterpillar cat 349 d2 l vg excavator (prefix pfd) service repair manual (pfd...fjskekxcddmmme
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 27 steps for assembly, installing components like seals, pistons, housing, plates and head in reverse order of disassembly. Tools required are listed in tables. Cautions are provided regarding cleaning, marking parts, and applying lubricant before assembly.
Caterpillar cat 349 d2 l excavator (prefix zae) service repair manual (zae000...fjskekxcddmmme
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal of a C13 engine. It outlines 11 steps to remove the rear gear group involving removing bolts, gears, seals, and bearings. It then outlines 12 steps to install the rear gear group in reverse order, noting specific tools and torque specifications. Separate sections provide 2 step instructions each for removing the flywheel and installing the crankshaft rear seal.
Caterpillar cat 349 f excavator (prefix hlb) service repair manual (hlb00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349F and 349F L excavators. It begins by listing the required tools and safety precautions. The disassembly process is then described in 32 steps and illustrated with diagrams, removing components like the motor head assembly, piston assembly, barrel assembly, swashplate, and shaft assembly. The assembly section provides specifications, lubrication and torque requirements for components, and illustrated assembly steps in reverse order.
Caterpillar cat 349 f excavator (prefix bz2) service repair manual (bz200001 ...fjskekxcddmmme
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy. Diagrams illustrate each step for clarification. The goal is to fully disassemble the travel motor into its individual parts for repair or replacement.
Caterpillar cat 349 e l vg excavator (prefix etc) service repair manual (etc0...fjskekxcddmmme
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque is required for all bolts.
Caterpillar cat 349 e l vg excavator (prefix kfx) service repair manual (kfx0...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section has 13 steps and specifies torques and lubricants for reinstalling components in reverse order. Tools, torque specifications, and component descriptions are provided in tables throughout.
Caterpillar cat 349 e l excavator (prefix whz) service repair manual (whz0000...fjskekxcddmmme
The document provides instructions for disassembling and assembling the final drive of a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...fjskekxcddmmme
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly process reverses the disassembly steps and includes applying sealant and pressing components together using various tools. Cleanliness is emphasized throughout.
Caterpillar cat 349 e l excavator (prefix spg) service repair manual (spg0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves 24 steps to remove components like the head assembly, brake housing, barrel assembly, pistons, and bearings. The assembly process reverses this with 13 steps like installing seals, springs, pins and bearings onto components before lowering the rotating group into the motor housing. Precautions and torque specifications are provided for correct reassembly.
Caterpillar cat 349 e l excavator (prefix rgh) service repair manual (rgh0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar cat 349 e l excavator (prefix mzw) service repair manual (mzw0000...fjskekxcddmmme
This document provides disassembly and assembly instructions for the final drive of a 349E L excavator. It includes specifications for the components, required tools, assembly procedures with illustrations, and torque specifications. The procedures describe cleaning and applying lubricants to parts, measuring clearances, installing bearings and seals, and adjusting shims to set proper spacing before tightening bolts and setscrews to specified torques.
Caterpillar cat 349 e l excavator (prefix mpz) service repair manual (mpz0000...fjskekxcddmmme
This document provides instructions for removing and installing a crankshaft vibration damper and pulley on a 349E L excavator. The procedure involves removing the fan drive, support brackets, drive belt, and bolts securing the pulley assembly. Tooling such as guide studs is used to support the pulley assembly during removal. The installation procedure is the reverse of removal. Proper torque is applied to the securing bolts and lubricant is used where appropriate.
Caterpillar cat 349 e l excavator (prefix kfx) service repair manual (kfx0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E L VG excavator. It includes 27 steps for disassembly, removing components like seals, springs, bearings, and housing pieces. The assembly section lists 14 steps and specifies torque values and lubricants for reinstalling components in reverse order. Tools, torque specifications, and component descriptions are provided in supporting tables throughout.
Caterpillar cat 349 e l excavator (prefix fjb) service repair manual (fjb0000...fjskekxcddmmme
This document provides instructions for disassembling and assembling the hydraulic fan drive on a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 e l excavator (prefix etc) service repair manual (etc0000...fjskekxcddmmme
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque specifications are provided for reinstallation.
Caterpillar cat 349 e excavator (prefix whz) service repair manual (whz00001 ...fjskekxcddmmme
The document provides instructions for disassembling and assembling the final drive on a 349E excavator. It describes 33 steps to disassemble the final drive components including removing the carrier assembly, planetary gears, ring gear, and sprocket housing. It also lists the required tools and specifications. The assembly section outlines 14 steps, applying anti-seize compound and Loctite to bearings and seals during reinstallation of components in reverse order of disassembly.
Caterpillar cat 349 e excavator (prefix spg) service repair manual (spg00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves removing 27 individual components from the motor housing, rotating group, and brake housing. The assembly process describes installing the components in reverse order and includes specifications for various parts. Proper lubrication and torque specifications are noted throughout.
Caterpillar cat 349 e excavator (prefix rgh) service repair manual (rgh00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Torque specifications and lubrication requirements are provided for many components.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...fjskekxcddmmme
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 d2 l vg excavator (prefix sdm) service repair manual (sdm...fjskekxcddmmme
The document provides instructions for disassembling and assembling a travel motor. It lists 30 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 31 steps for assembly, reinstalling these components in reverse order. Precautions are given to prevent contamination and ensure proper installation of parts like O-rings, seals, and pins in their original locations. Tools required are listed in a table.
Caterpillar cat 349 d2 l vg excavator (prefix pfd) service repair manual (pfd...fjskekxcddmmme
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 27 steps for assembly, installing components like seals, pistons, housing, plates and head in reverse order of disassembly. Tools required are listed in tables. Cautions are provided regarding cleaning, marking parts, and applying lubricant before assembly.
Caterpillar cat 349 d2 l excavator (prefix zae) service repair manual (zae000...fjskekxcddmmme
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal of a C13 engine. It outlines 11 steps to remove the rear gear group involving removing bolts, gears, seals, and bearings. It then outlines 12 steps to install the rear gear group in reverse order, noting specific tools and torque specifications. Separate sections provide 2 step instructions each for removing the flywheel and installing the crankshaft rear seal.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018640
Rear Power Take-Off (RPTO) - Remove
SMCS - 1165-011-RE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove" for the
correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. If necessary, remove the OEM equipment from the rear power take-off (RPTO).
1/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. Illustration 1 g02069019
Illustration 2 g02069023
2. Remove bolts (1). Remove adapter (2) from flywheel housing (9). Remove O-ring seal (3)
(not shown).
2/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. Note: Make a temporary mark on the adapter and the flywheel housing in order to show the
correct orientation of the adapter.
3. Remove bolts (4). Remove adapter (5) from flywheel housing (9). Remove O-ring seal (6)
(not shown).
Note: Make a temporary mark on the adapter and the flywheel housing in order to show the
correct orientation of the adapter.
4. Remove gear (7) from crankshaft (8).
5. If necessary, follow Steps 5.a through Steps 5.b in order to remove the sleeve bearing from
the adapter.
a. Place adapter (2) onto suitable support.
b. Use Tooling (A) and a suitable press in order to remove sleeve bearing (10) from
adapter (2).
6. Repeat Steps 6.a through Step 6.b in order to remove the sleeve bearing from adapter (5).
a. Place adapter (5) onto suitable support.
b. Use Tooling (A) and a suitable press in order to remove sleeve bearing (10) from
adapter (5).
Illustration 3 g02069020
3/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. 7. Remove gear assembly (11) and gear assembly (12) from flywheel housing (9).
Illustration 4 g02069021
Illustration 5 g02069453
8. Remove bolts (13). Remove gear (17) and idler hub (15) from flywheel housing (9).
4/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. 9. Remove bolts (14). Remove gear (18) and idler hub (16) from flywheel housing (9).
10. If necessary, follow Steps 10.a through Steps 10.b in order to remove the sleeve bearing
from the gear.
a. Place gear (17) onto suitable support.
b. Use Tooling (A) and a suitable press in order to remove sleeve bearing (19) from gear
(17).
Illustration 6 g03453499
11. Repeat Steps 11.a through Step 11.b in order to remove the sleeve bearing from the
remaining gear.
a. Place gear (18) onto suitable support.
b. Use Tooling (A) and a suitable press in order to remove sleeve bearing (19a) from
gear (18).
5/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. Illustration 7 g02069024
12. If necessary, follow Steps 12.a through Steps 12.b in order to remove the sleeve bearings
from the flywheel housing.
a. Use a suitable tool in order to remove sleeve bearing (20) from flywheel housing (9).
b. Repeat Step 12.a in order to remove sleeve bearing (21) from flywheel housing (9).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:22:20 UTC+0800 2020
6/6(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018641
Rear Power Take-Off (RPTO) - Install
SMCS - 1165-012-RE
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that all components of the rear power take-off (RPTO) are clean and free from wear
and damage.
1/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Illustration 2 g02069024
2. If necessary, follow Steps 2.a through Steps 2.c in order to install the sleeve bearings from
the flywheel housing.
a. Accurately align oil Holes (X) in sleeve bearing (20) with the oil holes in flywheel
housing (9).
b. Use Tooling (A) in order to install sleeve bearing (20) into flywheel housing (9).
Note: Ensure that the oil holes are correctly aligned. If the oil holes are not correctly
aligned, the sleeve bearing should be removed.
c. Repeat Step 2.a through Steps 2.b in order to install sleeve bearing (21) to flywheel
housing (9).
3/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. Illustration 3 g02070455
3. If necessary, follow Steps 3.a through Steps 4 in order to install the sleeve bearing to the
gears.
a. Place gear (17) onto suitable support.
b. Accurately align Grooves (Z) in sleeve bearing (19) with Grooves (Y) in gear (17).
c. Use Tooling (A) and a suitable press in order to install sleeve bearing (19) into gear
(17).
4/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. Illustration 4 g03453500
4. Repeat Steps 3.a through Step 3.c in order to install the sleeve bearing to gear (18).
a. Place gear (18) onto suitable support.
b. Accurately align Grooves (Z) in sleeve bearing (19a) with Grooves (Y) in gear (18).
c. Use Tooling (A) and a suitable press in order to install sleeve bearing (19a) into gear
(18).
5/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. Illustration 5 g02069021
5. Lubricate idler hub (15) and gear (17) with clean oil. Install idler hub (15) to gear (17).
Note: Ensure that the gear and the idler hub are correctly oriented.
6. Install gear (17) and idler hub (15) assembly to flywheel housing (9).
Note: Ensure that the oil hole in the idler hub is correctly positioned.
7. Install bolts (13) to idler hub (15) and hand tighten bolts.
Note: Ensure that the idler hub is correctly aligned to the flywheel housing.
8. Repeat Steps 5 through Step 7 in order to install gear (18), idler hub (16) and bolts (14) to
flywheel housing (9).
9. Tighten bolts (13) and bolts (14) to a torque of 100 N·m (74 lb ft).
10. Ensure that there is tactile backlash between gear (17) and gear (18). Ensure that there is
end play between the idler hubs and the gears.
6/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. Illustration 6 g02069020
11. install gear assembly (11) and gear assembly (12) to flywheel housing (9).
7/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. Illustration 8 g02070473
12. If necessary, follow Steps 12.a through Steps 12.c in order to install the sleeve bearings to
the adapters.
a. Place adapter (2) onto suitable support.
b. Use Tooling (A) and a suitable press in order to install sleeve bearing (10) into
adapter (2).
c. Repeat Steps 12.a through Step 12.b in order to install the sleeve bearing into adapter
(5).
13. Install a new O-ring seal (3) (not shown) to adapter (2).
14. Install adapter (2) to flywheel housing (9).
Note: Ensure correct orientation of the adapter.
15. Install bolts (1) and tighten the bolts to a torque of 55 N·m (41 lb ft).
16. Install a new O-ring seal (6) (not shown) to adapter (5).
17. Install adapter (5) to flywheel housing (9).
Note: Ensure correct orientation of the adapter.
18. Install bolts (4) and tighten the bolts to a torque of 55 N·m (41 lb ft).
9/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
17. 19. Ensure that there is tactile backlash between the gears. Ensure that there is end play between
the gears and the flywheel housing and the adapters.
20. Install gear (7) to crankshaft (8).
21. If necessary, install the OEM equipment to the rear power take-off (RPTO).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct
procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:23:16 UTC+0800 2020
10/10(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05909511
Vibration Damper and Pulley - Remove
SMCS - 1205-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
Start By:
A. Remove the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove
and Install" for the correct procedure.
Note: The weight of the assembly of the crankshaft pulley, the vibration damper, and the
crankshaft adapter is approximately 22 kg (48 lb).
1/3(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
19. Illustration 1 g02368017
1. Use a suitable tool in order to prevent the crankshaft from rotating. Use Tooling (B) to
remove one Torx screws (1) from crankshaft pulley assembly (2) .
2. Install Tooling (A) into crankshaft pulley assembly (2) .
3. Remove remaining Torx screws (1) from crankshaft pulley assembly (2) .
4. Remove crankshaft pulley assembly (2) .
5. Remove Tooling (A) .
2/3(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Illustration 2 g02368018
6. If necessary, follow Step 6.a through Step 6.b in order to remove friction shim (3) from the
crankshaft.
a. Remove the front seal from the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
b. Remove friction shim (3) .
7. If necessary, follow Step 7.a through Step 7.c in order to disassemble vibration damper,
crankshaft pulley from crankshaft adapter.
a. Place the crankshaft pulley assembly onto a suitable support.
b. Remove bolts (7) from crankshaft pulley assembly (2) .
c. Remove vibration damper (6) and crankshaft pulley (5) from adapter (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 6 09:24:11 UTC+0800 2020
3/3(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05909517
Vibration Damper and Pulley - Install
SMCS - 1205-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
C 8T-3052 Degree Wheel 1
D -
Guide Studs
M12 x 1.75 by 50 mm
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
22. Illustration 1 g02368018
1. Ensure that the crankshaft adapter and the front of the crankshaft are clean and free from
damage.
2. Inspect vibration damper (6) for damage. If necessary, replace the vibration damper.
3. If necessary, follow Step 3.a through Step 3.f in order to install vibration damper, crankshaft
pulley to crankshaft adapter.
a. Place crankshaft adapter (4) onto a suitable support.
b. Install Tooling (D) crankshaft adapter (4) .
c. Install crankshaft pulley (5) and vibration damper (6) over Tooling (D) .
d. Install bolts (7) to the crankshaft pulley assembly.
Note: Evenly space bolts (7) around the crankshaft pulley assembly.
e. Remove Tooling (D) .
f. Tighten bolts (7) to a torque of 115 N·m (85 lb ft).
4. If necessary, install friction shim (3) . Follow Step 4.a through Step 4.b in order to install
friction shim (3) .
a. Install friction shim (3) .
2/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
23. b. Install a new front seal to the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
5. Install Tooling (A) to the crankshaft.
Illustration 2 g02368017
6. Install crankshaft pulley assembly (2) onto the crankshaft.
7. Install one Torx screws (1) to crankshaft pulley assembly (2) hand tighten.
8. Remove Tooling (A) .
9. Install remaining Torx screws (1) to crankshaft pulley assembly (2) .
10. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten Torx screws (1)
to a torque of 40 N·m (29 lb ft).
11. Use Tooling (B) and Tooling (C) to turn Torx screws (1) through an additional 120 degrees.
End By: Install the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt -
Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Mon Jul 6 09:25:07 UTC+0800 2020
3/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330F EXCAVATOR KFA
Configuration: 330F L & 330F LN Excavators KFA00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines for Caterpillar Built Machines
Media Number -UENR4468-15 Publication Date -01/06/2015 Date Updated -30/10/2018
i05018646
Crankshaft Front Seal - Remove and Install - Crankshaft
Front Seal for Heavy Duty Front Cover
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 278-2636 Front Oil Seal Removal Tool 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
26. Illustration 1 g02048634
1. Position Tooling (A) on the nose of the crankshaft. Screw Tooling (A) into crankshaft front
seal (2).
Note: Do not damage the edge of the front cover for the crankshaft front seal.
2. Screw the bolt into Tooling (A) in order to remove crankshaft front seal (2) from front cover
(1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B
9U-6206 Stud Front Seal Installer 1
9U-6207 Plate 1
9U-6209 Sleeve Plate 1
9U-6211 Seal Installer Tool 1
366-5984 Installer Assembly 1
2/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
27. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the bore for the crankshaft front oil seal in the front cover is clean and free from
damage.
Illustration 2 g03417117
2. Assemble Tooling (B).
3. Correctly position a new crankshaft front seal (2) to front cover (1).
Note: If the crankshaft front seal is supplied with a sleeve, remove the sleeve from the
crankshaft front seal before installation.
4. Use Tooling (B) to install crankshaft front seal (2) to front cover (1). Ensure that the front
face of the crankshaft front seal is installed to a depth of 6.5 ± 0.2 mm (0.256 ± 0.008 inch).
5. Remove Tooling (B) from the crankshaft.
End By:
3/4(W)
w
2020/7/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...