The document provides step-by-step instructions for disassembling and assembling a travel motor. It lists 28 steps for disassembly, removing components like the head, port plate, bearings, brake piston, plates, and seals. It then lists 16 steps for assembly, replacing components in reverse order and noting specifics like lubrication, alignment marks, and press fittings. Precautions are provided around spring force, fluid containment, and correct positioning of parts like the cam plate and keys.
This document provides instructions for disassembling and assembling the travel motor of a 320D2 GC excavator. The disassembly procedure outlines 27 steps to fully disassemble the travel motor. These include removing the head, brake piston, piston guide, barrel assembly, and other components. The assembly procedure then lists 28 steps to reassemble all components in the reverse order, making sure to clean parts and apply the proper seals, oils, and torques. Precise alignment of parts is important for correct reassembly.
Caterpillar cat 323 d2 l excavator (prefix flc) service repair manual (flc000...fusjejkdkmse
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the head, barrel assembly, piston guide, brake piston, and shaft assembly. The assembly process describes 25 steps and requires applying clean oil and ensuring components like the cam plate and keys are correctly installed. Special tools and cautions are noted to properly complete the work.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
Caterpillar cat 323 d2 l excavator (prefix jeg) service repair manual (jeg000...fusjejkdkmse
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the head, brake piston, barrel assembly, and shaft. The assembly section lists 14 steps, starting with cleaning components and ending by installing the cam plate and keys into the motor body. Precise alignment of parts is emphasized to ensure proper reassembly.
Caterpillar cat 330 c l excavator (prefix jcd) service repair manual (jcd0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The travel motor disassembly procedure involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals.
2. Travel motor assembly requires installing components in reverse order, applying thread lock compound and oil, and torquing bolts to specified values.
3. Special tools are required to remove races, seals, and retainers, and marks must be made to ensure correct piston and component positioning during reassembly.
Caterpillar cat 323 d2 l excavator (prefix pjp) service repair manual (pjp000...fusjejkdkmse
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the head, barrel assembly, brake piston, and shaft. The assembly process describes 23 steps and includes precautions to ensure correct installation of components like the cam plate, piston shoe assemblies, and seals. Special tools may be required and clean hydraulic oil should be applied to sliding surfaces during reassembly.
Caterpillar cat 323 d2 l excavator (prefix ycr) service repair manual (ycr000...fusjejkdkmse
The document provides step-by-step instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, removing components like the head, check valves, fittings, seals, piston guide, barrel assembly, and shaft assembly. It then lists 26 steps for assembly, reinstalling these components in reverse order and ensuring proper alignment of parts. Special care must be taken with components like the cam plate and keys to avoid damage during assembly.
This document provides instructions for disassembling and assembling the travel motor of a 320D2 GC excavator. The disassembly procedure outlines 27 steps to fully disassemble the travel motor. These include removing the head, brake piston, piston guide, barrel assembly, and other components. The assembly procedure then lists 28 steps to reassemble all components in the reverse order, making sure to clean parts and apply the proper seals, oils, and torques. Precise alignment of parts is important for correct reassembly.
Caterpillar cat 323 d2 l excavator (prefix flc) service repair manual (flc000...fusjejkdkmse
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the head, barrel assembly, piston guide, brake piston, and shaft assembly. The assembly process describes 25 steps and requires applying clean oil and ensuring components like the cam plate and keys are correctly installed. Special tools and cautions are noted to properly complete the work.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
Caterpillar cat 323 d2 l excavator (prefix jeg) service repair manual (jeg000...fusjejkdkmse
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the head, brake piston, barrel assembly, and shaft. The assembly section lists 14 steps, starting with cleaning components and ending by installing the cam plate and keys into the motor body. Precise alignment of parts is emphasized to ensure proper reassembly.
Caterpillar cat 330 c l excavator (prefix jcd) service repair manual (jcd0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The travel motor disassembly procedure involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals.
2. Travel motor assembly requires installing components in reverse order, applying thread lock compound and oil, and torquing bolts to specified values.
3. Special tools are required to remove races, seals, and retainers, and marks must be made to ensure correct piston and component positioning during reassembly.
Caterpillar cat 323 d2 l excavator (prefix pjp) service repair manual (pjp000...fusjejkdkmse
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the head, barrel assembly, brake piston, and shaft. The assembly process describes 23 steps and includes precautions to ensure correct installation of components like the cam plate, piston shoe assemblies, and seals. Special tools may be required and clean hydraulic oil should be applied to sliding surfaces during reassembly.
Caterpillar cat 323 d2 l excavator (prefix ycr) service repair manual (ycr000...fusjejkdkmse
The document provides step-by-step instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, removing components like the head, check valves, fittings, seals, piston guide, barrel assembly, and shaft assembly. It then lists 26 steps for assembly, reinstalling these components in reverse order and ensuring proper alignment of parts. Special care must be taken with components like the cam plate and keys to avoid damage during assembly.
John deere 975 combines service repair manual (tm4387)fjjsekkksmeik
The document provides instructions for the reader to click on a link to access a complete manual with no waiting. It notes that if clicking the link does not work, the reader should first download the PDF document and then click on it to access the manual.
1996 polaris indy tran sport snowmobile service repair manualfjjsekkksmeik
This document provides publication numbers and service bulletin indexes for Polaris snowmobiles from 1994-1998. It lists the model, model number, owner's manual part number, parts manual part number, and other relevant documentation for each year. The section also indexes service bulletins by number and provides brief descriptions of the technical issues covered in each bulletin for 1994-1995 models.
This document provides instructions for renewing various components of the 2.9L Jaguar engine, including the auxiliary drive shaft, camshaft, crankshaft, cylinder head, oil pump, timing chains, and other parts. The renewal process involves removing worn parts and cleaning and inspecting components before fitting replacements and reassembling the engine. Special tools are required for some tasks like removing oil seals.
1989 polaris indy 500 sks snowmobile service repair manualfjjsekkksmeik
The document describes vehicle models and specifications for 1985-1995. It provides details on model identification numbers, engine types, dimensions, features and specifications for each model year. Model details are given for 1985 models including the Star, SS, Indy Trail, Indy 600, 600SE and LongTrack.
Yamaha outboard ft50 cet service repair manual l 450101 fjjsekkksmeik
The document is a service manual that provides general information and technical tips about an FT50C outboard motor. It includes:
1) An overview of the manual format and symbols used as well as safety procedures for working on the motor.
2) Details on the motor features such as its use of leaded gasoline, newly designed four carburetors, and CDI ignition unit.
3) Explanations of technical aspects like the carburetor operation including its starting, idle, medium and high speed functions.
Terex girolift 5022 perfora telescopic handler service repair manualfjjsekkksmeik
This document is a workshop manual that provides instructions for maintenance and repairs of a handler with a telescopic boom. It contains sections on general information, safety regulations, technical specifications, inspections, disassembly and assembly, troubleshooting, maintenance of specific components like the axle, engine, pumps, gearbox, and load limiter. The appendices provide information on tools, torque specifications, weights of parts, and refilling specifications. The manual is intended to allow safe and proper maintenance of the machine.
Perkins phaser 135 ti model al (euro 2) diesel engine service repair manualfjjsekkksmeik
This document provides a workshop manual for the Perkins Phaser 135 Ti 4 cylinder diesel engine. It contains specifications, instructions for disassembly and assembly of engine components, timing procedures, and safety information. The manual is divided into chapters covering the cylinder head, pistons and connecting rods, crankshaft, timing components, cylinder block, and other systems such as fuel, cooling, and aspiration.
Caterpillar cat m315 c wheeled excavator (prefix h2b) service repair manual (...fjjsekkksmeik
The document provides instructions for disassembling the piston pump (swing) of an M315C wheeled excavator. It describes removing 22 individual parts from the pump housing including the servo valve, charge pump, gears, head, port plate, relief valves, spool, and adjustment screw. Cleanliness is important when disassembling to prevent dirt from entering the internal mechanisms. Personal injury precautions are also noted regarding hydraulic pressure and spring force.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...fjjsekkksmeik
This document provides assembly and disassembly instructions for the main hydraulic pump of a M315C wheeled excavator. It lists 42 steps to disassemble the pump by removing components like valves, springs, pistons, seals and bearings. It notes to mark components' orientations. Reassembly follows the reverse of disassembly, noting to replace bolts and apply threadlock. Safety warnings caution of parts under spring pressure and ensuring fluid containment.
Caterpillar cat 330 d2 l excavator (prefix xdr) service repair manual (xdr000...fjjsekkksmeik
The document provides instructions for installing and removing an engine oil pump, water pump, and water temperature regulator on a Caterpillar 330D2 excavator. The oil pump installation involves cleaning components, installing various parts in sequence using specific tools and torques. The water pump removal requires draining coolant and removing hoses and bolts. Its installation aligns parts using guide studs and torques bolts in a given order. Removing the temperature regulator involves draining coolant and disconnecting hoses.
Caterpillar cat 330 d2 l excavator (prefix hsp) service repair manual (hsp000...fjjsekkksmeik
The document provides instructions for disassembling a 330D2 excavator travel motor. The 27 step procedure includes removing the head, brake piston, barrel assembly, cam plate, shaft assembly, and other components. Special tools are required and technicians are warned to contain fluids, mark components for reassembly, and use care when handling springs or moving parts that could cause injury.
Caterpillar cat 330 d2 l excavator (prefix her) service repair manual (her000...fjjsekkksmeik
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves 37 steps to remove all components of the final drive. Key steps include removing the final drive cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly process has 36 steps and involves installing components in reverse order while applying anti-seize compound and ensuring proper bearing preload using shims.
Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex000...fjjsekkksmeik
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps including removing the final drive cover, carrier assembly, planetary gears, ring gears, and other components. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components given their significant weights ranging from 32 to 550 kilograms. Cleanliness is emphasized to prevent dirt entry during disassembly.
Caterpillar cat 330 d2 l excavator (prefix ex7) service repair manual (ex7000...fjjsekkksmeik
The document provides instructions for disassembling and assembling a travel motor. It is a service repair manual for Caterpillar 330D2 and 330D2 L excavators. The disassembly procedure involves removing 28 different parts from the travel motor in 27 steps. The assembly procedure reverses this process and puts the travel motor back together in 25 steps, reinstalling the parts in the reverse order that they were removed. Precise instructions are given for each step to ensure correct reassembly.
Caterpillar cat 330 d2 l excavator (prefix ebp) service repair manual (ebp000...fjjsekkksmeik
The document provides disassembly instructions for a 330D2 and 330D2 L excavator travel motor in 28 steps. It begins by having the technician thoroughly clean and secure the travel motor vertically before disassembling. The steps then carefully describe removing components like the head, brake piston, plates, seals, bearings, and more. Pictures accompany each step to illustrate the proper procedure. Safety notices are included to handle fluids and springs carefully.
Caterpillar cat 330 d2 l excavator (prefix dtg) service repair manual (dtg000...fjjsekkksmeik
The document provides the disassembly procedure for a 330D2 excavator travel motor. It lists 28 steps to fully disassemble the travel motor, including removing the head, brake piston, plates and discs, rotating assembly, seals, and other internal components. Tools required are also listed. The procedure aims to clearly identify each part and ensure proper reinstallation of components in their original positions and orientations.
John deere 975 combines service repair manual (tm4387)fjjsekkksmeik
The document provides instructions for the reader to click on a link to access a complete manual with no waiting. It notes that if clicking the link does not work, the reader should first download the PDF document and then click on it to access the manual.
1996 polaris indy tran sport snowmobile service repair manualfjjsekkksmeik
This document provides publication numbers and service bulletin indexes for Polaris snowmobiles from 1994-1998. It lists the model, model number, owner's manual part number, parts manual part number, and other relevant documentation for each year. The section also indexes service bulletins by number and provides brief descriptions of the technical issues covered in each bulletin for 1994-1995 models.
This document provides instructions for renewing various components of the 2.9L Jaguar engine, including the auxiliary drive shaft, camshaft, crankshaft, cylinder head, oil pump, timing chains, and other parts. The renewal process involves removing worn parts and cleaning and inspecting components before fitting replacements and reassembling the engine. Special tools are required for some tasks like removing oil seals.
1989 polaris indy 500 sks snowmobile service repair manualfjjsekkksmeik
The document describes vehicle models and specifications for 1985-1995. It provides details on model identification numbers, engine types, dimensions, features and specifications for each model year. Model details are given for 1985 models including the Star, SS, Indy Trail, Indy 600, 600SE and LongTrack.
Yamaha outboard ft50 cet service repair manual l 450101 fjjsekkksmeik
The document is a service manual that provides general information and technical tips about an FT50C outboard motor. It includes:
1) An overview of the manual format and symbols used as well as safety procedures for working on the motor.
2) Details on the motor features such as its use of leaded gasoline, newly designed four carburetors, and CDI ignition unit.
3) Explanations of technical aspects like the carburetor operation including its starting, idle, medium and high speed functions.
Terex girolift 5022 perfora telescopic handler service repair manualfjjsekkksmeik
This document is a workshop manual that provides instructions for maintenance and repairs of a handler with a telescopic boom. It contains sections on general information, safety regulations, technical specifications, inspections, disassembly and assembly, troubleshooting, maintenance of specific components like the axle, engine, pumps, gearbox, and load limiter. The appendices provide information on tools, torque specifications, weights of parts, and refilling specifications. The manual is intended to allow safe and proper maintenance of the machine.
Perkins phaser 135 ti model al (euro 2) diesel engine service repair manualfjjsekkksmeik
This document provides a workshop manual for the Perkins Phaser 135 Ti 4 cylinder diesel engine. It contains specifications, instructions for disassembly and assembly of engine components, timing procedures, and safety information. The manual is divided into chapters covering the cylinder head, pistons and connecting rods, crankshaft, timing components, cylinder block, and other systems such as fuel, cooling, and aspiration.
Caterpillar cat m315 c wheeled excavator (prefix h2b) service repair manual (...fjjsekkksmeik
The document provides instructions for disassembling the piston pump (swing) of an M315C wheeled excavator. It describes removing 22 individual parts from the pump housing including the servo valve, charge pump, gears, head, port plate, relief valves, spool, and adjustment screw. Cleanliness is important when disassembling to prevent dirt from entering the internal mechanisms. Personal injury precautions are also noted regarding hydraulic pressure and spring force.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...fjjsekkksmeik
This document provides assembly and disassembly instructions for the main hydraulic pump of a M315C wheeled excavator. It lists 42 steps to disassemble the pump by removing components like valves, springs, pistons, seals and bearings. It notes to mark components' orientations. Reassembly follows the reverse of disassembly, noting to replace bolts and apply threadlock. Safety warnings caution of parts under spring pressure and ensuring fluid containment.
Caterpillar cat 330 d2 l excavator (prefix xdr) service repair manual (xdr000...fjjsekkksmeik
The document provides instructions for installing and removing an engine oil pump, water pump, and water temperature regulator on a Caterpillar 330D2 excavator. The oil pump installation involves cleaning components, installing various parts in sequence using specific tools and torques. The water pump removal requires draining coolant and removing hoses and bolts. Its installation aligns parts using guide studs and torques bolts in a given order. Removing the temperature regulator involves draining coolant and disconnecting hoses.
Caterpillar cat 330 d2 l excavator (prefix hsp) service repair manual (hsp000...fjjsekkksmeik
The document provides instructions for disassembling a 330D2 excavator travel motor. The 27 step procedure includes removing the head, brake piston, barrel assembly, cam plate, shaft assembly, and other components. Special tools are required and technicians are warned to contain fluids, mark components for reassembly, and use care when handling springs or moving parts that could cause injury.
Caterpillar cat 330 d2 l excavator (prefix her) service repair manual (her000...fjjsekkksmeik
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves 37 steps to remove all components of the final drive. Key steps include removing the final drive cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly process has 36 steps and involves installing components in reverse order while applying anti-seize compound and ensuring proper bearing preload using shims.
Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex000...fjjsekkksmeik
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps including removing the final drive cover, carrier assembly, planetary gears, ring gears, and other components. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components given their significant weights ranging from 32 to 550 kilograms. Cleanliness is emphasized to prevent dirt entry during disassembly.
Caterpillar cat 330 d2 l excavator (prefix ex7) service repair manual (ex7000...fjjsekkksmeik
The document provides instructions for disassembling and assembling a travel motor. It is a service repair manual for Caterpillar 330D2 and 330D2 L excavators. The disassembly procedure involves removing 28 different parts from the travel motor in 27 steps. The assembly procedure reverses this process and puts the travel motor back together in 25 steps, reinstalling the parts in the reverse order that they were removed. Precise instructions are given for each step to ensure correct reassembly.
Caterpillar cat 330 d2 l excavator (prefix ebp) service repair manual (ebp000...fjjsekkksmeik
The document provides disassembly instructions for a 330D2 and 330D2 L excavator travel motor in 28 steps. It begins by having the technician thoroughly clean and secure the travel motor vertically before disassembling. The steps then carefully describe removing components like the head, brake piston, plates, seals, bearings, and more. Pictures accompany each step to illustrate the proper procedure. Safety notices are included to handle fluids and springs carefully.
Caterpillar cat 330 d2 l excavator (prefix dtg) service repair manual (dtg000...fjjsekkksmeik
The document provides the disassembly procedure for a 330D2 excavator travel motor. It lists 28 steps to fully disassemble the travel motor, including removing the head, brake piston, plates and discs, rotating assembly, seals, and other internal components. Tools required are also listed. The procedure aims to clearly identify each part and ensure proper reinstallation of components in their original positions and orientations.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D2 EXCAVATOR EX7
Configuration: 330D2 L OEM EX700001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03124522
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded RodM12 x 1.75 by 250 mm (10 in) long 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove".
1/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
2/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. 4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00887302
6. Remove O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 3 g00887311
7. Remove O-ring seals (6) . Remove springs (7) .
3/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B) .
8. Place a shop towel over brake piston (8) . Retain brake piston (8) with Tooling (B) . Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y) . Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
4/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 6 g00887336
9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
11. Remove plates (13) and friction discs (14) .
Illustration 8 g00887401
5/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Illustration 9 g00887405
12. Install Tooling (C) into shaft (15) . Use a prybar to remove the rotating assembly (16) from
the housing.
13. Remove Tooling (C) from shaft (15) .
Illustration 10 g00887424
14. Remove shaft (15) from rotating assembly (16) .
6/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 11 g00887426
15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15) .
Illustration 12 g00887445
16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
Illustration 13 g00887463
17. Rotate shaft (15) . Install shaft (15) into a suitable press. Install Tooling (E) . Remove
bearing race (19) from shaft (15) .
7/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 14 g00887501
18. Remove cam plate (20) from barrel assembly (21) .
Illustration 15 g00887520
19. Remove piston assemblies and retainer plate (22) from barrel assembly (21) .
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
8/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 16 g00887558
20. Remove ball (23) and springs (24) .
Illustration 17 g00887578
21. Remove bearing (25) .
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27) .
24. Remove seal (28) .
9/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 19 g00887619
25. Remove bolts (29) and cover (30) .
Illustration 20 g00887729
26. Remove seal (31) and backup ring (32) .
Illustration 21 g00887754
27. Remove piston actuator (33) and seal (34) .
10/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Illustration 22 g00887762
28. Remove O-ring seal (35) from the housing of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 20:51:43 UTC+0800 2020
11/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D2 EXCAVATOR EX7
Configuration: 330D2 L OEM EX700001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i01706705
Travel Motor - Assemble
SMCS - 4351-016
S/N - DTG1-UP
S/N - EBP1-UP
S/N - EX71-UP
S/N - FEX1-UP
S/N - HSP1-UP
S/N - JFG1-UP
S/N - KER1-UP
S/N - LJE1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
1. Make sure that all of the components of the travel motor are thoroughly clean and free of
dirt and debris prior to assembly.
1/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 1 g00510595
2. Install retaining ring (35) in the groove on shaft (34).
3. Install bearing (36) on shaft (34) with a press. Install the bearing until the bearing contacts
the retaining ring.
4. Install the other retaining ring on the opposite side of bearing (36).
Illustration 2 g00510598
5. Install inner race (37) on the end of shaft (34) until the inner race is seated against the
shoulder on the shaft.
2/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 3 g00651891
(a) Body
6. Apply a thin coat of 5P-3413 Pipe Sealant on Surfaces (Y) of the body of the travel motor.
7. Use Tooling (A) in order to install lip seal (38).
8. Install lip type seal (38) in the body of the travel motor. Install the lip seal so that the sealing
lip is facing in the direction that is shown. Make sure that the lip seal contacts the
counterbore in the body of the travel motor.
Note: Slowly rotate shaft assembly (34) during the installation in order to make sure that the
shaft assembly does not bind in the body of the travel motor.
9. Apply clean hydraulic oil on the lip of lip seal (38).
10. Use a press to install shaft assembly (34) in the body of the travel motor. Slowly rotate the
shaft during the installation in order to make sure that the shaft does not bind. Make sure
that the bearing on the shaft contacts the counterbore in the body of the travel motor.
3/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 4 g00651960
NOTICE
The locating pin on each key is not centered. In order to prevent
damage to the barrel assembly during assembly of the travel motor, the
keys must be installed as shown. Also, the keys must be installed in the
key's original location in the body of the travel motor.
11. Install the two locating pins and two keys (31) in the body of the travel motor, as shown.
Illustration 5 g00510547
12. Install cam plate (30) in the body of the travel motor in the cam plate's original location.
Make sure that the two pistons and two keys (31) in the body of the travel motor engage
properly with the cam plate.
4/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 6 g00510504
13. Install nine springs (29) in the barrel. Install spacer (28) and guide (27) on the barrel.
Illustration 7 g00878253
14. Install piston shoe assemblies (25) in the piston shoe assembly's original bores in shoe
retainer (24).
15. Apply clean hydraulic oil in the bores of the barrel and on piston shoe assemblies (25).
Install the piston shoe assemblies with the shoe retainer in the piston shoe assembly's
original bore in barrel (26).
NOTICE
Make sure that the cam plate is correctly engaged with the two pistons
in the body of the travel motor prior to installing the barrel assembly.
When the body of the travel motor is tilted to allow the installation of
the barrel assembly, the cam plate can slide off of the two pistons. The
remaining parts of the travel motor can be assembled with the cam
plate in the incorrect position.
Extensive damage will result from the incorrect installation of the cam
plate. Follow the exact installation procedure to prevent damage.
5/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. 16. Apply clean hydraulic oil on the sliding surfaces of the cam plate, on the piston shoe
assemblies and on the splined shaft of the travel motor.
Illustration 8 g00485953
17. Route a piece of strong string through an opening for the cam plate tension adjusters. Route
the string over the sliding surface of cam plate (30) and through the opposite opening for the
cam plate tension adjusters. Hold the string taut in order to keep cam plate (30) correctly
engaged with keys (31). Keep the string taut and position the body of the travel motor on the
body's side. Do not release the tension on the string at this time. Install barrel assembly (23)
as a unit on the shaft. Pull the string out of the body of the travel motor. It may be necessary
to pull the barrel assembly and the piston shoe assemblies away from the cam plate slightly
in order to release the string.
Illustration 9 g00651967
18. Install O-ring seal (21) and backup ring (22) on piston guide (19), as shown.
6/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 10 g00510356
19. Place the body of the travel motor in a vertical position.
20. Apply clean hydraulic oil on five friction plates (20) and the four steel plates. Install the
plates in alternating order in the body of the travel motor. Start with a friction plate and end
with a friction plate.
21. Install piston guide (19) in the body of the travel motor until the piston guide contacts the
counterbore in the body of the travel motor.
Illustration 11 g00878297
Note: Make sure that brake piston (14) is thoroughly clean and free of dirt and debris.
22. Install O-ring seal (16). Install backup ring (15).
23. Install O-ring seal (17). Install backup ring (18).
24. Apply a thin coat of hydraulic oil on the surfaces of piston (14) which contact the body of
the travel motor. Install piston (14) in the body of the travel motor by hand. It may be
necessary to use a soft faced hammer to seat the piston correctly.
7/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 12 g00878299
Illustration 13 g00878239
25. Install washer set (12) in piston (14), as shown.
26. Install O-ring seals (13) in the body of the travel motor, as shown.
Illustration 14 g00510605
8/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. 27. Install the two pistons and two stoppers (39) in the housing of the travel motor. Tighten the
stoppers to a torque of 140 ± 14 N·m (105 ± 10 lb ft).
Illustration 15 g00510351
28. Install the O-ring seals on fittings (10). Apply 5P-3413 Pipe Sealant on the threads of
fittings (10). Install the fittings in the head, as shown.
29. Install plugs (11) in the head. Tighten each plug to a torque of 15 ± 2 N·m (11 ± 1 lb ft).
Illustration 16 g00510349
Illustration 17 g00510341
9/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. 30. Apply a thin coat of 9S-3263 Thread Lock Compound on the threads of the two check
valves. Install the check valves in the head.
31. Install seat (7), poppet (8) and spring (9) in the head at Location (X).
32. Install O-ring seal (6) in the head, as shown.
33. Install bearing (3) in the head until the bearing contacts the counterbore in the cover.
34. Apply 1U-6396 O-Ring Assembly Compound on port plate (4). Install the port plate in the
port plate's original position on the motor cover.
35. Use a shim or shims (5) so that the following requirements are met.
Note: During the following checks, turn the travel motor output shaft in a clockwise
direction.
a. The travel motor output shaft does not rotate with an applied torque of 440 N·m
(325 lb ft) or more with the parking brake release port open.
b. The travel motor output shaft rotates with an applied torque of 29 N·m (21 lb ft) or
less when the parking brake release port is pressurized to 780 kPa (115 psi) with both
the inlet port and the outlet port open to the hydraulic oil tank.
Note: It may be necessary to remove head (2) several times in order to determine the correct
thickness of shim or shims (5) that are used to adjust the rolling torque of the travel motor
output shaft.
36. Apply a thin layer of 5P-0960 Molybdenum Grease on shim or shims (5). Install the shim or
shims on the head. The grease will hold the shim or shims in place during the installation of
the head. Install the head on the body of the travel motor.
Illustration 18 g00510326
37. Place head (2) in the head's original position on the travel motor. Install socket head bolts
(1) that secure the head. Tighten the socket head bolts to a torque of 175 ± 18 N·m
(130 ± 13 lb ft).
NOTICE
10/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. To prevent possible damage to the travel motor, fill the unit with oil at
least to the fill port before operating the machine. Refer to the
Operation and Maintenance Manual for the correct oil specification.
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install" in this
manual.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jul 19 20:52:41 UTC+0800 2020
11/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330D2 EXCAVATOR EX7
Configuration: 330D2 L OEM EX700001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03124523
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded Rod M12 x 1.75 X 250 mm (10 in) long 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G 9S-3263 Thread Lock Compound -
Note: Replace all O-ring seals and gaskets. Apply a light film of"10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause trouble later. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
1/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33) .
2/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Illustration 3 g00887729
3. Install backup ring (32) and seal (31) .
Illustration 4 g00887619
4. Install cover (30) and bolts (29) . Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
3/11(W)
w
2020/7/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...