The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under spring load.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
This document provides instructions for removing and installing a pump control valve on a 725 Articulated Truck. It begins by noting safety precautions for working with hydraulic systems and outlines necessary tools. The removal procedure includes marking all lines and hoses for identification before disconnection, and disconnecting the tee fitting from the pump control valve by loosening the retaining nut. The installation procedure is not shown, but presumably involves reconnecting the tee fitting and any other disconnected components.
Caterpillar cat 950 k wheel loader (prefix j5m) service repair manual (j5m000...fjsqazkekdmme
The document provides instructions for installing the rear power take-off (RPTO) on a 950K wheel loader. It describes cleaning components, aligning sleeve bearings, installing gears and idler hubs onto the flywheel housing using press tools, lubricating parts, and tightening bolts to specified torques. The 20-step procedure includes installing adapters and seals, checking backlash and end play, and attaching the gear assembly to the crankshaft.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
Caterpillar cat 330 d mh excavator (prefix pel) service repair manual (pel000...fjjskekdmme
This document provides installation instructions for a main hydraulic pump on a 330D excavator. It lists 54 steps to assemble various components of the pump such as pistons, bearings, gears, covers, and valves. Tools required include lever pullers, link brackets, and retaining ring pliers. Photos illustrate each step, and torque specifications are provided for fasteners. The overall process installs the pump, connects hoses and wiring, and mounts related components back onto the excavator.
Caterpillar cat 324 e l excavator (prefix pnw) service repair manual (pnw0000...JayHaines2
This document provides instructions for disassembling and assembling the travel motor of a 324E L Excavator. It lists the required tools and parts and provides 28 steps to disassemble the travel motor by removing components like the head, O-rings, springs, brake piston, plates, and bearings. It then lists 19 steps to assemble the travel motor by reinstalling these components in the reverse order, noting proper lubrication and alignment of parts.
Caterpillar cat 424 d backhoe loader (prefix bgp) service repair manual (bgp0...fjjsefkskemmm
This document provides instructions for disassembling and assembling the front drive and steering axle of a Caterpillar 424D backhoe loader. The disassembly process involves removing components like the carrier gear, hub, seals, bearings and kingpins. The assembly process describes installing these components in reverse order and adjusting shims to achieve the correct rolling resistance. Required tools are listed.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
This document provides instructions for removing and installing a pump control valve on a 725 Articulated Truck. It begins by noting safety precautions for working with hydraulic systems and outlines necessary tools. The removal procedure includes marking all lines and hoses for identification before disconnection, and disconnecting the tee fitting from the pump control valve by loosening the retaining nut. The installation procedure is not shown, but presumably involves reconnecting the tee fitting and any other disconnected components.
Caterpillar cat 950 k wheel loader (prefix j5m) service repair manual (j5m000...fjsqazkekdmme
The document provides instructions for installing the rear power take-off (RPTO) on a 950K wheel loader. It describes cleaning components, aligning sleeve bearings, installing gears and idler hubs onto the flywheel housing using press tools, lubricating parts, and tightening bolts to specified torques. The 20-step procedure includes installing adapters and seals, checking backlash and end play, and attaching the gear assembly to the crankshaft.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
Caterpillar cat 330 f ln excavator (prefix kfa) service repair manual (kfa000...fksjksmmde
The document provides instructions to remove the rear power take-off (RPTO) from an excavator engine. It involves removing gears, hubs, adapters and sleeve bearings from the flywheel housing using press tools. O-rings and seals should also be replaced before installing the components in reverse order. Proper alignment of oil holes and lubrication of parts is important for correct installation.
Caterpillar cat 330 d mh excavator (prefix pel) service repair manual (pel000...fjjskekdmme
This document provides installation instructions for a main hydraulic pump on a 330D excavator. It lists 54 steps to assemble various components of the pump such as pistons, bearings, gears, covers, and valves. Tools required include lever pullers, link brackets, and retaining ring pliers. Photos illustrate each step, and torque specifications are provided for fasteners. The overall process installs the pump, connects hoses and wiring, and mounts related components back onto the excavator.
Caterpillar cat 324 e l excavator (prefix pnw) service repair manual (pnw0000...JayHaines2
This document provides instructions for disassembling and assembling the travel motor of a 324E L Excavator. It lists the required tools and parts and provides 28 steps to disassemble the travel motor by removing components like the head, O-rings, springs, brake piston, plates, and bearings. It then lists 19 steps to assemble the travel motor by reinstalling these components in the reverse order, noting proper lubrication and alignment of parts.
Caterpillar cat 424 d backhoe loader (prefix bgp) service repair manual (bgp0...fjjsefkskemmm
This document provides instructions for disassembling and assembling the front drive and steering axle of a Caterpillar 424D backhoe loader. The disassembly process involves removing components like the carrier gear, hub, seals, bearings and kingpins. The assembly process describes installing these components in reverse order and adjusting shims to achieve the correct rolling resistance. Required tools are listed.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat 336 e h excavator (prefix hdw) service repair manual (hdw0000...fjskekdmjekm
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes installing seals, springs, plates, pistons, bearings and other parts back into their proper positions, taking care to align markings and lubricate components. Tools and torque specifications are provided for each step.
Caterpillar cat 336 e l excavator (prefix bzy) service repair manual (bzy0000...fjskekmdm
This document provides instructions for disassembling and assembling a 336E L excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate and keys. Special tools are listed that are required for tasks like removing races and installing seals. Safety notices advise wearing protective equipment when working with spring-loaded parts.
Caterpillar cat 336 e lh excavator (prefix rza) service repair manual (rza000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly procedure involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly procedure describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lh excavator (prefix gny) service repair manual (gny000...fjskekdmjekm
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 336 e l excavator (prefix dpx) service repair manual (dpx0000...fjskekmdm
This document provides instructions for disassembling and assembling a 336E L excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, O-rings, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly process in 21 steps and provides warnings about spring-loaded components and ensuring proper alignment of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, bearing puller group, and Loctite.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...cdsaas
The document provides instructions for assembling a travel motor. It describes 33 steps for installing various components like seals, pistons, plates, and bearings. Measurements are taken throughout to ensure proper assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system. The travel motor must be filled with the correct oil type before operation to prevent damage.
This document is a service manual for MerCruiser #26 GM 4-cylinder 181 cid (3.0L) marine engines. It provides information and procedures for technicians to service these engines, including removal/installation, mechanical systems, electrical systems, fuel systems, cooling systems, exhaust systems and power steering. The manual outlines safety warnings and identifies the models covered. It also provides general information to help technicians such as how to use the manual, read parts manuals, understand directional references and engine rotation.
Mercury mercruiser marine engines #28 bravo sterndrives service repair manualcdfzxs
This document is the service manual for MerCruiser #28 Bravo Sterndrives. It provides information on maintenance, troubleshooting, removal and installation procedures. The manual begins with important safety notices and outlines the document structure. Subsequent sections cover lubrication and maintenance schedules, troubleshooting common issues, and detailed removal and installation instructions for sterndrive components. Torque specifications, tool requirements and other technical details are included to aid mechanics in properly servicing these sterndrives.
This document is the service manual for MerCruiser #24 GM V-8 305 CID (5.0L) / 350 CID (5.7L) marine engines. The manual contains sections on important information, removal and installation, the engine, electrical systems, fuel systems, cooling systems, exhaust systems, drives, power steering systems, and troubleshooting. It provides information and instructions for mechanics to service these MerCruiser engines.
Komatsu sk510 5 skid steer loader service repair manual (sn 37 df00001 and up)cdfzxs
This document is a shop manual for the SK510-5 skid-steer loader. It provides information on structure and function, testing and adjusting procedures, disassembly and assembly instructions, and maintenance standards. The manual contains safety precautions that must be followed when working on the loader. It explains how to properly lift heavy components using hoists or cranes. Standard tightening torques are also provided for bolts, nuts, and other fasteners.
Komatsu d63 e 12 dozer bulldozer service repair manual (sn 2001 and up)cdfzxs
1) The document is a shop manual that provides instructions for servicing and repairing a Bulldozer model D63E-12 from serial numbers 2001 and up.
2) It consists of several sections that cover specifications, structure and maintenance standards, testing and adjustments, troubleshooting, and disassembly/assembly of components.
3) The sections are further divided into topics that each have a form number identifying individual documents covering specific components and systems.
Komatsu ck25 1 skid steer loader service repair manual (sn f00003 and up)cdfzxs
This document provides safety information and instructions for servicing a CK25-1 crawler skid-steer loader. It discusses general safety precautions, preparations for work, precautions during work, and hoisting instructions. Safety symbols are defined that mark important safety points in the manual. The document instructs technicians to carefully follow all safety cautions, prepare the work area and equipment properly before starting repairs, and use lifting equipment correctly when hoisting components.
Daewoo doosan de12 tis diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining Daewoo DE series diesel engines, including the DE12, DE12T, DE12TI, and DE12TIS models. It describes the engine components and specifications. The manual includes symbols to indicate maintenance tasks and instructions for proper disposal of waste. It aims to help customers and distributors maintain engines in optimum condition through correct operation and proper maintenance.
Daewoo doosan de12 ti diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration, replacing the fan belt if damaged, and checking the engine oil level is important to maintain optimum engine performance and durability. The manual explains maintenance procedures and contains symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo doosan de12 t diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining Daewoo DE series diesel engines, including the DE12, DE12T, DE12TI, and DE12TIS models. It describes the key features of the engines such as their OMEGA combustion bowl design and specifications including power, torque, and idle speeds. Exploded diagrams show the main engine components and assemblies in the various models. The manual instructs technicians on general repair procedures and identifies symbols used to indicate different service operations.
Daewoo doosan de12 diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Crown ws2000 series forklift service repair manualcdfzxs
This document is a service and parts manual for a series of trucks. It contains sections on maintenance, lubrication, hydraulic systems, drive units, electrical systems, and components. The manual provides instructions for inspection, maintenance, repair, and replacement of parts. It includes diagrams of hydraulic and electrical systems, lists of lubrication points, and torque specifications for fasteners.
Crown wp2300 s series pallet truck service repair manualcdfzxs
This document provides revisions and maintenance information for the WP2300S Series order number 812529-006. It includes:
- Revisions made to various pages and components, including additions and corrections to safety switches, platform control switches, and platform logic circuits.
- Sections covering maintenance procedures such as lubrication and adjustments, hydraulics, electrical components, brakes, steering and other systems.
- Electrical diagrams for standard and optional configurations of folded and fixed platforms.
Crown wp2300 series pallet truck service repair manualcdfzxs
The document provides an overview of maintenance and repair for a WP2300 series truck. It includes sections on lubrication and adjustment, hydraulics, drive unit, electrics, brakes, steering, lifting mechanism, cylinders, electrical diagrams and hydraulic schematics. Safety symbols and notes are defined. Only authorized personnel should perform maintenance following the procedures in this manual. Replacement parts must be original equipment.
Crown wp2000 s series pallet truck service repair manualcdfzxs
This document is a service manual that provides maintenance and repair instructions for a WP2000S series truck. It contains sections on safety, introduction, lubrication and adjustment, hydraulics, drive unit, electrics, brakes, steering, lifting mechanism, cylinders, electrical diagrams, and hydraulic schematics. The introduction section notes that the manual should be used by trained personnel, and covers operating instructions, service training, replacement parts orders, and the structure and numbering of the manual pages.
This document provides instructions for disassembling a travel motor from an excavator model 326D2 L. The 27 step procedure includes removing the head, brake piston, plates, and friction discs. Special tools are required to remove components like the rotating assembly, bearing races, and retaining rings. Technicians are advised to mark components like the pistons and barrel assembly to ensure correct reassembly.
This document provides instructions for removing the rear power take-off (RPTO) from a C7.1 engine. It outlines 10 steps to remove gears, hubs, adapters and other components from the flywheel housing. These include removing bolts, gears, seals and sleeve bearings from housings, gears and adapters. Special tools and marks are recommended to ensure correct reinstallation. Cleaning and inspection of removed parts is also specified.
Caterpillar cat 336 e h excavator (prefix hdw) service repair manual (hdw0000...fjskekdmjekm
The document provides instructions for disassembling and assembling the travel motor on a 336E excavator model. It outlines 27 steps for disassembly, which includes removing the head, seals, springs, brake piston, plates, and seals from various components. It then outlines 28 steps for assembly, which reverses the disassembly process and includes installing seals, springs, plates, pistons, bearings and other parts back into their proper positions, taking care to align markings and lubricate components. Tools and torque specifications are provided for each step.
Caterpillar cat 336 e l excavator (prefix bzy) service repair manual (bzy0000...fjskekmdm
This document provides instructions for disassembling and assembling a 336E L excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate and keys. Special tools are listed that are required for tasks like removing races and installing seals. Safety notices advise wearing protective equipment when working with spring-loaded parts.
Caterpillar cat 336 e lh excavator (prefix rza) service repair manual (rza000...fjskekdmjekm
This document provides instructions for disassembling and assembling the travel motor on 336E LH and 336E LNH excavator models. The disassembly procedure involves removing 27 components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly procedure describes installing these 27 components in reverse order and provides notes to ensure proper installation of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, and bearing puller group.
Caterpillar cat 336 e lh excavator (prefix gny) service repair manual (gny000...fjskekdmjekm
The document provides assembly instructions for a travel motor in 28 steps. It details installing various components like seals, springs, pistons, and plates in the proper sequence. It also describes attaching the travel motor to the excavator and tightening bolts to the specified torques. The removal and installation procedures for a final drive and travel motor are also outlined in 13 steps, including draining oil first and marking components for reinstallation.
Caterpillar cat 336 e l excavator (prefix dpx) service repair manual (dpx0000...fjskekmdm
This document provides instructions for disassembling and assembling a 336E L excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, O-rings, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly process in 21 steps and provides warnings about spring-loaded components and ensuring proper alignment of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, bearing puller group, and Loctite.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...cdsaas
The document provides instructions for assembling a travel motor. It describes 33 steps for installing various components like seals, pistons, plates, and bearings. Measurements are taken throughout to ensure proper assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system. The travel motor must be filled with the correct oil type before operation to prevent damage.
This document is a service manual for MerCruiser #26 GM 4-cylinder 181 cid (3.0L) marine engines. It provides information and procedures for technicians to service these engines, including removal/installation, mechanical systems, electrical systems, fuel systems, cooling systems, exhaust systems and power steering. The manual outlines safety warnings and identifies the models covered. It also provides general information to help technicians such as how to use the manual, read parts manuals, understand directional references and engine rotation.
Mercury mercruiser marine engines #28 bravo sterndrives service repair manualcdfzxs
This document is the service manual for MerCruiser #28 Bravo Sterndrives. It provides information on maintenance, troubleshooting, removal and installation procedures. The manual begins with important safety notices and outlines the document structure. Subsequent sections cover lubrication and maintenance schedules, troubleshooting common issues, and detailed removal and installation instructions for sterndrive components. Torque specifications, tool requirements and other technical details are included to aid mechanics in properly servicing these sterndrives.
This document is the service manual for MerCruiser #24 GM V-8 305 CID (5.0L) / 350 CID (5.7L) marine engines. The manual contains sections on important information, removal and installation, the engine, electrical systems, fuel systems, cooling systems, exhaust systems, drives, power steering systems, and troubleshooting. It provides information and instructions for mechanics to service these MerCruiser engines.
Komatsu sk510 5 skid steer loader service repair manual (sn 37 df00001 and up)cdfzxs
This document is a shop manual for the SK510-5 skid-steer loader. It provides information on structure and function, testing and adjusting procedures, disassembly and assembly instructions, and maintenance standards. The manual contains safety precautions that must be followed when working on the loader. It explains how to properly lift heavy components using hoists or cranes. Standard tightening torques are also provided for bolts, nuts, and other fasteners.
Komatsu d63 e 12 dozer bulldozer service repair manual (sn 2001 and up)cdfzxs
1) The document is a shop manual that provides instructions for servicing and repairing a Bulldozer model D63E-12 from serial numbers 2001 and up.
2) It consists of several sections that cover specifications, structure and maintenance standards, testing and adjustments, troubleshooting, and disassembly/assembly of components.
3) The sections are further divided into topics that each have a form number identifying individual documents covering specific components and systems.
Komatsu ck25 1 skid steer loader service repair manual (sn f00003 and up)cdfzxs
This document provides safety information and instructions for servicing a CK25-1 crawler skid-steer loader. It discusses general safety precautions, preparations for work, precautions during work, and hoisting instructions. Safety symbols are defined that mark important safety points in the manual. The document instructs technicians to carefully follow all safety cautions, prepare the work area and equipment properly before starting repairs, and use lifting equipment correctly when hoisting components.
Daewoo doosan de12 tis diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining Daewoo DE series diesel engines, including the DE12, DE12T, DE12TI, and DE12TIS models. It describes the engine components and specifications. The manual includes symbols to indicate maintenance tasks and instructions for proper disposal of waste. It aims to help customers and distributors maintain engines in optimum condition through correct operation and proper maintenance.
Daewoo doosan de12 ti diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration, replacing the fan belt if damaged, and checking the engine oil level is important to maintain optimum engine performance and durability. The manual explains maintenance procedures and contains symbols to indicate removal, installation, cleaning, and other service operations.
Daewoo doosan de12 t diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining Daewoo DE series diesel engines, including the DE12, DE12T, DE12TI, and DE12TIS models. It describes the key features of the engines such as their OMEGA combustion bowl design and specifications including power, torque, and idle speeds. Exploded diagrams show the main engine components and assemblies in the various models. The manual instructs technicians on general repair procedures and identifies symbols used to indicate different service operations.
Daewoo doosan de12 diesel engine service repair manualcdfzxs
This maintenance manual provides instructions for maintaining DAEWOO DE series diesel engines, models DE12, DE12T, DE12TI, and DE12TIS. It describes the engine components and specifications. Proper maintenance like checking coolant concentration and fan belt tension are important to maintain optimum engine performance and durability. The manual explains maintenance procedures and includes symbols to indicate removal, installation, cleaning, and other service operations.
Crown ws2000 series forklift service repair manualcdfzxs
This document is a service and parts manual for a series of trucks. It contains sections on maintenance, lubrication, hydraulic systems, drive units, electrical systems, and components. The manual provides instructions for inspection, maintenance, repair, and replacement of parts. It includes diagrams of hydraulic and electrical systems, lists of lubrication points, and torque specifications for fasteners.
Crown wp2300 s series pallet truck service repair manualcdfzxs
This document provides revisions and maintenance information for the WP2300S Series order number 812529-006. It includes:
- Revisions made to various pages and components, including additions and corrections to safety switches, platform control switches, and platform logic circuits.
- Sections covering maintenance procedures such as lubrication and adjustments, hydraulics, electrical components, brakes, steering and other systems.
- Electrical diagrams for standard and optional configurations of folded and fixed platforms.
Crown wp2300 series pallet truck service repair manualcdfzxs
The document provides an overview of maintenance and repair for a WP2300 series truck. It includes sections on lubrication and adjustment, hydraulics, drive unit, electrics, brakes, steering, lifting mechanism, cylinders, electrical diagrams and hydraulic schematics. Safety symbols and notes are defined. Only authorized personnel should perform maintenance following the procedures in this manual. Replacement parts must be original equipment.
Crown wp2000 s series pallet truck service repair manualcdfzxs
This document is a service manual that provides maintenance and repair instructions for a WP2000S series truck. It contains sections on safety, introduction, lubrication and adjustment, hydraulics, drive unit, electrics, brakes, steering, lifting mechanism, cylinders, electrical diagrams, and hydraulic schematics. The introduction section notes that the manual should be used by trained personnel, and covers operating instructions, service training, replacement parts orders, and the structure and numbering of the manual pages.
This document provides instructions for disassembling a travel motor from an excavator model 326D2 L. The 27 step procedure includes removing the head, brake piston, plates, and friction discs. Special tools are required to remove components like the rotating assembly, bearing races, and retaining rings. Technicians are advised to mark components like the pistons and barrel assembly to ensure correct reassembly.
The document provides instructions for disassembling a travel motor. It begins by having the technician remove the travel motor from the excavator and clean the outside. The technician is then instructed to fasten the motor vertically and mark it for alignment before disassembling. The summary proceeds to list the 27 steps to disassemble the various components of the travel motor, including removing the head, brake piston, barrel assembly, and shaft assembly. Tools required for the disassembly are also provided in a table.
The document provides instructions for disassembling a travel motor from an excavator. It describes 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, springs, seals, and other internal parts. Precautions are provided to watch for spring forces and use lifting devices due to the weight of some components. Detailed illustrations accompany each step.
Caterpillar cat 325 d mh excavator (prefix rjk) service repair manual (rjk000...cdfzxs
The document provides instructions for disassembling and assembling the travel motor of a 325D MH Excavator. It lists 28 steps for disassembly, requiring various tools to remove components like the head, port plate, springs, brake piston, plates, and seals. It then lists 23 steps for assembly, applying thread lock compound and ensuring proper installation of keys, cam plate, friction discs, backup rings, seals, and brake piston. Cleanliness is stressed and O-rings must be replaced.
Caterpillar cat 325 d mh excavator (prefix c4h) service repair manual (c4h000...cdfzxs
This document provides instructions to disassemble a final drive on a 325D MH EXCAVATOR. It outlines 31 steps to remove components like the cover, gears, carrier assemblies, housing and seals. Special tools are required and cleanliness is important to prevent dirt from entering during reassembly. The procedure includes notes on alignment marks, weights of parts, and disassembling planetary gears within carrier assemblies.
Caterpillar cat 325 c excavator (prefix s2c) service repair manual (s2c00001 ...cdfzxs
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and tapping guides into place. Safety notices warn of potential injury from parts propelled by springs and ensure clean parts to prevent premature wear.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i02344155
Piston Motor (Hydraulic Fan) - Assemble
SMCS - 1386-016-QP; 5058-016-FM; 5058-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9152 Bearing Puller Gp 1
C 1P-1857 Retaining Ring Pliers 1
D 1P-0510 Driver Gp 1
E 1U-6396 O-Ring Assembly Compound 1
F 1P-1854 Retaining Ring Pliers 1
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. A reconditioning procedure should not be degraded
because of a low cost component such as an O-ring or a gasket. Use Tooling (E) during the
assembly procedure.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: Apply a light film of SAE 10W oil to all components before assembly.
1/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00882512
1. Use Tooling (D) in order to install bearing cup (27) .
Note: Bearing cup (27) must be fully seated. Bearing cup (27) must be properly seated in
order for the motor to assemble properly.
Illustration 2 g00882505
2. Rotate housing (3) . Use Tooling (D) in order to install seal (26) .
3. Use Tooling (C) in order to install retaining ring (25) .
2/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Illustration 3 g00883246
4. Install shaft (2) and bearing cone (16) in a suitable press. Press bearing cone (16) onto shaft
(2) .
Note: Bearing cone (16) must be fully seated. Bearing cone (16) must be properly seated in
order for the motor to assemble properly.
5. Assemble the rotating group in the following manner:
Illustration 4 g00882894
a. Install pins (24) in the top of barrel assembly (19) .
3/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 5 g00882494
b. Rotate barrel assembly (19) . Install washer (23) and spring (22) . Place retaining ring
(21) on top of spring (22) .
Note: Do not attempt to install retaining ring (21) .
Illustration 6 g00882927
c. Rotate the barrel assembly. Retain the contents of the barrel. Position guide (20) on
pins (24) .
d. Install shaft (2) and the bearing through the barrel assembly.
Note: The shaft will align the barrel assembly.
Illustration 7 g01163862
4/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
e. Install Tooling (A) and barrel assembly (19) into a suitable press.
f. Compress the spring. Use Tooling (F) in order to install retaining ring (21) .
g. Slowly release the pressure on barrel assembly (19) .
h. Remove the shaft from barrel assembly (19) .
Illustration 8 g00882451
6. Install pistons and plate (18) into barrel assembly (19) .
Illustration 9 g00882324
7. Install swashplate (17) onto rotating group (14) .
5/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Note: Barrel assembly (19) is rotating group (14) upon the installation of the pistons.
Note: Place identifying marks on swashplate (17) in order to locate two holes on the top of
the swashplate.
Illustration 10 g00882976
8. Install shaft (2) into rotating group (14) .
Note: Splines in shaft (2) must engage splines in rotating group (14) .
Illustration 11 g00882984
6/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 12 g00882988
9. Align swashplate (17) with housing (3) .
Note: The holes on the top of swashplate (17) must engage the dowels in housing (3) .
Illustration 13 g00882991
10. Install rotating group (14) into housing (3) .
Illustration 14 g00882992
7/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. 11. Raise the temperature of sleeve (15) . Install sleeve (15) onto shaft (2) .
Illustration 15 g00882156
12. Install shim (13) onto shaft (2) .
Illustration 16 g00882123
13. Install bearing cone (12) onto shaft (2) .
Note: Bearing cone (12) is a slip fit.
8/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 17 g00882112
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install valve assembly (9) , sleeve (10) , and plug (11) into cover (5) .
Illustration 18 g00881963
15. Use Tooling (A) to install bearing cup (8) into cover (5) .
9/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 19 g00883138
Illustration 20 g00881953
16. Install port plate (6) onto cover (5) .
Note: Take note of the slot in the reverse side of port plate (6) . The slot will receive the
dowel in cover (5) .
17. Install O-ring seal (7) on cover (5) .
Illustration 21 g00881945
10/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. 18. Install cover (5) onto housing (3) .
19. Secure cover (5) with bolts (4) .
Illustration 22 g00881939
20. Install key (1) into shaft (2) .
End By: Install the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Install ".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 17 13:43:50 UTC+0800 2020
11/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i02344156
Piston Motor (Hydraulic Fan) - Install
SMCS - 1386-012-QP; 5058-012-FM
Installation Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 1 g00883712
1. Position piston motor (23) into the bracket. Secure the piston motor with bolts (22) .
Illustration 2 g00883819
2. Install adapter (21) onto the piston motor.
Illustration 3 g00883705
3. Install nut (20) , fan blade (19) , and bolts (18) .
2/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 4 g00883690
4. Attach a suitable lifting device to the piston motor and fan assembly (17) . The weight of the
piston motor and fan assembly (17) is approximately 29 kg (65 lb). Position the piston
motor and fan assembly (17) . Install bolts (16) .
Illustration 5 g00883675
5. Install hose assemblies (15) .
3/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 6 g00883666
6. Install upper fan guard (14) and bolts (13) .
Illustration 7 g00883641
7. Install tube assemblies (10) and (9) . Install bolts (12) and (11) .
Illustration 8 g00883636
8. Slide the hoses from tube assemblies (10) and (9) into position. Install hose clamps (8) .
4/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 9 g00883581
9. Install strap (7) and bolts (6) .
Illustration 10 g00883563
10. Install brace (5) and bolts (4) .
Illustration 11 g00883517
11. Install plates (1) , (2) , and (3) . Install the bolts.
5/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i04776349
Gear Pump (Fan Drive) - Remove
SMCS - 1387-011-GT; 5073-011-HFN
Removal Procedure
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release" in this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the oil from the hydraulic oil tank into a suitable container for storage or disposal.
The capacity of the hydraulic oil tank is 175 L (46 US gal).
1/2(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 1 g02883378
Illustration 2 g02879096
2. Remove hose assemblies (2) and (3).
3. Remove nuts (1). Remove gear pump (4).
4. Remove nut (5). Remove gear (6), gasket (8), flange (9), key (10), and the O-ring seal.
5. Use a suitable press to remove bearing (7) from gear (6).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 17 13:45:42 UTC+0800 2020
2/2(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i04959810
Gear Pump (Fan Drive) - Install
SMCS - 1387-012-GT; 5073-012-HFN; 5073
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
1/3(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 1 g02879096
1. Use a suitable press to Install bearing (7) onto gear (6).
2. Install key (10). Install the O-ring seal onto flange (9). Install flange (9), gasket (8). Install
gear (6) and nut (5).
Note: Do not tighten nut at this time. The gear pump must be installed on the engine before
the nut is tightened. This procedure will prevent the pump from being damaged internally.
Illustration 2 g02883378
3. Position gear pump (4).
4. Secure gear pump (4) into position with bolts and nuts (1).
5. Remove the front access cover (not shown) in order to tighten nut (5). Tighten nut (5) to a
torque of 80 ± 8 N·m (59 ± 6 lb ft).
6. Install the front access cover.
7. Connect hose assemblies (2) and (3).
2/3(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i01796054
Handle (Joystick) - Remove and Install
SMCS - 5705-010
Removal Procedure
Illustration 1 g00739085
1. Remove the cover from the front of the console. Remove screws (1) .
1/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 2 g00739101
2. Remove screws (2) from the rear of the console.
Illustration 3 g00739106
3. Open armrest (3). Remove screws (4). Remove armrest (3) .
Illustration 4 g00739111
2/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. 4. Reposition cover (6) in order to access the harness assembly on the right hand console.
Disconnect harness assembly (5) .
5. Remove cover (6) from the console.
Illustration 5 g00739116
6. Disconnect harness assembly (7) from the joystick.
Illustration 6 g00739127
7. Lift rubber boot (8) over handle (9) .
Note: Mark the location of locknut (10) and the handle for installation procedures.
8. Hold nut (11). Loosen locknut (10). Unscrew handle (9) in order to remove the handle.
9. Remove rubber boot (8) from the handle.
Installation Procedure
3/6(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...