This document provides instructions for disassembling and assembling the travel motor of a 330C L excavator. It outlines 28 steps for disassembly, removing components like the head, springs, plates and seals. It then outlines 29 steps for assembly, replacing components and ensuring proper installation of items like pistons, bearings, seals and covers. Special tools are listed and safety notices provided. The overall process is described to thoroughly disassemble and then reassemble the travel motor.
Caterpillar cat 330 c l excavator (prefix dky) service repair manual (dky0000...hhjsekmdmm
The document provides instructions for disassembling and assembling the travel motor of a 330C L excavator. It lists 28 steps for disassembly, removing components like the head, plates, seals, and bearing races. It then lists 28 steps for assembly, reinstalling those components in reverse order and noting requirements like applying thread lock compounds and ensuring proper alignment of parts. Tools required are also listed. The overall document provides a detailed technical procedure for fully disassembling and reassembling the excavator's travel motor.
Caterpillar cat 330 c l excavator (prefix mca) service repair manual (mca0000...hhjsekmdmm
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat 330 c l excavator (prefix jcd) service repair manual (jcd0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The travel motor disassembly procedure involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals.
2. Travel motor assembly requires installing components in reverse order, applying thread lock compound and oil, and torquing bolts to specified values.
3. Special tools are required to remove races, seals, and retainers, and marks must be made to ensure correct piston and component positioning during reassembly.
Caterpillar cat 330 c l excavator (prefix gkx) service repair manual (gkx0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) Similarly, it outlines 28 steps for assembly, instructing technicians to replace all seals and gaskets and apply lubricant before reinstalling components in reverse order of disassembly. Cleanliness is emphasized throughout the process.
Hyster p177 (h3.5 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes lifting capacities, counterweight weights, tire sizes, fuel and fluid capacities, and electrical specifications for various Hyster truck models. It also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h3.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Caterpillar cat 330 c l excavator (prefix dky) service repair manual (dky0000...hhjsekmdmm
The document provides instructions for disassembling and assembling the travel motor of a 330C L excavator. It lists 28 steps for disassembly, removing components like the head, plates, seals, and bearing races. It then lists 28 steps for assembly, reinstalling those components in reverse order and noting requirements like applying thread lock compounds and ensuring proper alignment of parts. Tools required are also listed. The overall document provides a detailed technical procedure for fully disassembling and reassembling the excavator's travel motor.
Caterpillar cat 330 c l excavator (prefix mca) service repair manual (mca0000...hhjsekmdmm
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 23 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts to the specified torques.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat 330 c l excavator (prefix jcd) service repair manual (jcd0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The travel motor disassembly procedure involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals.
2. Travel motor assembly requires installing components in reverse order, applying thread lock compound and oil, and torquing bolts to specified values.
3. Special tools are required to remove races, seals, and retainers, and marks must be made to ensure correct piston and component positioning during reassembly.
Caterpillar cat 330 c l excavator (prefix gkx) service repair manual (gkx0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) Similarly, it outlines 28 steps for assembly, instructing technicians to replace all seals and gaskets and apply lubricant before reinstalling components in reverse order of disassembly. Cleanliness is emphasized throughout the process.
Hyster p177 (h3.5 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes lifting capacities, counterweight weights, tire sizes, fuel and fluid capacities, and electrical specifications for various Hyster truck models. It also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h3.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h2.5 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h2.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster n006 (h8.0 fts6) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h7.0 fts9) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h7.0 fts6) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications such as battery size and alternator output
- Transmission oil pressures and hydraulic system relief pressures
- Instructions for removing the drive axle, which include draining fluids and disconnecting brake and hydraulic lines
Hyster n006 (h7.0 ft) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h6.0 ft) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications such as battery size and alternator output
- Transmission oil pressures and hydraulic system relief pressures
- Instructions for removing the drive axle, which include draining fluids and disconnecting brake lines
Hyster l006 (h7.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models H6.0FT, H7.0FT, H8.0FT, and H9.0FT, including:
- Lifting capacities, weights, tire sizes, fuel and fluid capacities
- Engine oil, coolant, transmission oil, hydraulic oil, brake fluid specifications
- Electrical system components and specifications
- Transmission oil pressures
- Hydraulic and steering system relief pressures and components
- Instructions for removing the drive axle assembly, including draining fluids and disconnecting brake, cooling, and drive shaft components.
Hyster l006 (h6.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models H6.0FT, H7.0FT, H8.0FT, and H9.0FT, including:
- Lifting capacities and weights for each model
- Tire sizes, fuel capacities, fluid capacities and specifications for various systems
- Transmission oil pressures and relief pressures for hydraulic and steering systems
- Procedures for removing the drive axle, including draining fluids and disconnecting brake, cooling and driveline components.
Hyster k019 (h16 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h14 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h13 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Kion lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, mast speeds, hydraulic system specifications, transmission specifications, and torque specifications for servicing components. The document contains model-specific data for H8-H16XM and H6-H7XM-12EC units.
Hyster k019 (h10 xm 12 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h7 xm 12ec europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h6 xm 12ec europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Kion lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, mast speeds, hydraulic system specifications, transmission specifications, and torque specifications for servicing components. The document contains model-specific data for H8-H16XM lift trucks.
Hyster k007 (h12 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster k007 (h10 xms 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster k007 (h10 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster k007 (h9 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster k007 (h8 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Hyster p177 (h2.5 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster p177 (h2.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and repair information for Hyster lift trucks. It includes the lifting capacity, counterweight, tire size, fuel and fluid capacities, and electrical specifications for various Hyster truck models. The document also provides transmission oil pressure specifications and general transmission repair procedures.
Hyster n006 (h8.0 fts6) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h7.0 fts9) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h7.0 fts6) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications such as battery size and alternator output
- Transmission oil pressures and hydraulic system relief pressures
- Instructions for removing the drive axle, which include draining fluids and disconnecting brake and hydraulic lines
Hyster n006 (h7.0 ft) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications including battery, spark plug, and alternator specifications
- Transmission oil pressures for 2-speed and 3-speed transmissions
- Hydraulic system relief pressures
- Instructions for removing the drive axle, including draining fluids and disconnecting brake lines
Hyster n006 (h6.0 ft) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models, including:
- Lift capacities and counterweight weights for various models
- Tire sizes, fuel capacities, fluid capacities, and recommended fluids
- Electrical system specifications such as battery size and alternator output
- Transmission oil pressures and hydraulic system relief pressures
- Instructions for removing the drive axle, which include draining fluids and disconnecting brake lines
Hyster l006 (h7.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models H6.0FT, H7.0FT, H8.0FT, and H9.0FT, including:
- Lifting capacities, weights, tire sizes, fuel and fluid capacities
- Engine oil, coolant, transmission oil, hydraulic oil, brake fluid specifications
- Electrical system components and specifications
- Transmission oil pressures
- Hydraulic and steering system relief pressures and components
- Instructions for removing the drive axle assembly, including draining fluids and disconnecting brake, cooling, and drive shaft components.
Hyster l006 (h6.0 ft europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Hyster lift truck models H6.0FT, H7.0FT, H8.0FT, and H9.0FT, including:
- Lifting capacities and weights for each model
- Tire sizes, fuel capacities, fluid capacities and specifications for various systems
- Transmission oil pressures and relief pressures for hydraulic and steering systems
- Procedures for removing the drive axle, including draining fluids and disconnecting brake, cooling and driveline components.
Hyster k019 (h16 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h14 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h13 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Kion lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, mast speeds, hydraulic system specifications, transmission specifications, and torque specifications for servicing components. The document contains model-specific data for H8-H16XM and H6-H7XM-12EC units.
Hyster k019 (h10 xm 12 europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h7 xm 12ec europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Konecranes lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, transmission specifications, hydraulic system specifications like pump capacities and relief pressures, and specifications for items like tires, steering, brakes, and drive axles. Torque specifications are also provided for maintenance of components like transmissions, differentials, and steering systems.
Hyster k019 (h6 xm 12ec europe) forklift service repair manualhhjsekmdmm
This document provides specifications and service information for Cummins diesel engines and Kion lift trucks. It includes counterweight weights, basic truck weights, engine specifications like oil capacities and pressures, mast speeds, hydraulic system specifications, transmission specifications, and torque specifications for servicing components. The document contains model-specific data for H8-H16XM lift trucks.
Hyster k007 (h12 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster k007 (h10 xms 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster k007 (h10 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster k007 (h9 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Hyster k007 (h8 xm 6 europe) forklift service repair manualhhjsekmdmm
This document provides specifications for Caterpillar lift trucks including:
1) Counterweight weights ranging from 2900 kg to 7050 kg depending on the lift truck model.
2) Basic truck weights ranging from 9400 kg to 15,400 kg depending on options and tire type.
3) Engine specifications including displacement, compression ratio, oil pressure, and weight for Cummins QSB4.5 and QSB6.7 engines.
4) Capacities for engine oil, cooling system, hydraulic tank, transmission, drive axle, and fuel tank.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C L EXCAVATOR CYA
Configuration: 330C L Excavator CYA00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i03124522
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded RodM12 x 1.75 by 250 mm (10 in) long 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove".
1/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
2/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. 4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00887302
6. Remove O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 3 g00887311
7. Remove O-ring seals (6) . Remove springs (7) .
3/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B) .
8. Place a shop towel over brake piston (8) . Retain brake piston (8) with Tooling (B) . Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y) . Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
4/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. Illustration 6 g00887336
9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
11. Remove plates (13) and friction discs (14) .
Illustration 8 g00887401
5/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. Illustration 9 g00887405
12. Install Tooling (C) into shaft (15) . Use a prybar to remove the rotating assembly (16) from
the housing.
13. Remove Tooling (C) from shaft (15) .
Illustration 10 g00887424
14. Remove shaft (15) from rotating assembly (16) .
6/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. Illustration 11 g00887426
15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15) .
Illustration 12 g00887445
16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
Illustration 13 g00887463
17. Rotate shaft (15) . Install shaft (15) into a suitable press. Install Tooling (E) . Remove
bearing race (19) from shaft (15) .
7/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
9. Illustration 14 g00887501
18. Remove cam plate (20) from barrel assembly (21) .
Illustration 15 g00887520
19. Remove piston assemblies and retainer plate (22) from barrel assembly (21) .
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
8/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Illustration 16 g00887558
20. Remove ball (23) and springs (24) .
Illustration 17 g00887578
21. Remove bearing (25) .
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27) .
24. Remove seal (28) .
9/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. Illustration 19 g00887619
25. Remove bolts (29) and cover (30) .
Illustration 20 g00887729
26. Remove seal (31) and backup ring (32) .
Illustration 21 g00887754
27. Remove piston actuator (33) and seal (34) .
10/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. Illustration 22 g00887762
28. Remove O-ring seal (35) from the housing of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Sep 6 16:05:49 UTC+0800 2020
11/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C L EXCAVATOR CYA
Configuration: 330C L Excavator CYA00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i03124523
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded Rod M12 x 1.75 X 250 mm (10 in) long 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G 9S-3263 Thread Lock Compound -
Note: Replace all O-ring seals and gaskets. Apply a light film of"10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause trouble later. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
1/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33) .
2/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
15. Illustration 3 g00887729
3. Install backup ring (32) and seal (31) .
Illustration 4 g00887619
4. Install cover (30) and bolts (29) . Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
3/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. 5. Apply Tooling (G) to the mating surface of seal (28) . Use Tooling (E) in order to install
seal (28) .
6. Use Tooling (F) in order to install retaining ring (27) .
Illustration 6 g00887578
7. Rotate the housing.
8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25) .
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
4/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
17. 10. Install springs (24) into the barrel. Install ball (23) onto springs (24) .
Illustration 8 g00887520
11. Install piston assemblies and retainer plate (22) into barrel assembly (21) .
Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Install cam plate (20) onto barrel assembly (21) .
5/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15) .
Illustration 11 g00887426
14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15) .
Illustration 12 g00888710
6/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
19. 15. Install bearing race (18) onto shaft (15) .
Note: Bearing race (18) must contact retaining ring (17) .
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15) . Install shaft (15) into rotating assembly (16) .
17. Place the pump housing into Tooling (A) .
Illustration 14 g00887401
18. Use Tooling (C) in order to install rotating assembly (16) into the housing.
7/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Illustration 15 g00887501
Illustration 16 g00887578
19. The notches in cam plate (20) must align with keys (26) . The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
20. Install plates (13) and friction discs (14) into the housing.
8/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
21. Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8) .
24. Install brake piston (8) into the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level in
order to prevent damage to the O-ring seals.
9/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
22. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6) .
Illustration 21 g00887302
26. Install O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 22 g00887295
27. Install head (2) onto the body of the travel motor.
10/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
23. Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1) . Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By: Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Sep 6 16:06:45 UTC+0800 2020
11/11(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C L EXCAVATOR CYA
Configuration: 330C L Excavator CYA00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i02372696
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A Threaded Rod 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/3(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
26. Illustration 1 g00878123
2. Install new O-ring seal (5) . Apply clean hydraulic oil on the O-ring seal.
Illustration 2 g00707267
3. Fasten a suitable lifting device to travel motor (4) , as shown. The weight of travel motor (4)
is approximately 57 kg (125 lb).
Illustration 3 g00878121
2/3(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
27. 4. Carefully install travel motor (4) on Tooling (A) . Slide the travel motor into the final drive.
5. Install one of three bolts (5) that secures the travel motor to the final drive.
6. Remove Tooling (A) .
Illustration 4 g00707275
7. Install two remaining bolts (2) .
8. Connect hose assemblies (3) and (1) .
9. Fill the final drive with oil.
Reference: Refer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
Reference: Refer to Operation and Maintenance Manual, "Final Drive Oil Level - Check"
for the correct filling procedure.
10. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
End By: Install the travel brake valve. Refer to Disassembly and Assembly, "Counterbalance
Valve (Travel) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Sep 6 16:07:43 UTC+0800 2020
3/3(W)
w
2020/9/6
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...