1) The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It involves removing over 30 individual parts including gears, shafts, seals, and housings.
2) Special tools are required to remove some components, and safety precautions are noted regarding the weights of parts that need to be lifted, up to 550 kg for the entire final drive assembly.
3) Detailed illustrations accompany each step to show the specific components and orientation during disassembly. Cleanliness is emphasized to prevent dirt from entering internal mechanisms.
The document provides step-by-step instructions to disassemble a final drive assembly. It involves removing over 30 individual parts in a specific sequence, including covers, gears, shafts, seals, washers, and housings. Various tools are required to remove retaining rings, pins, bolts and separate connected pieces. Precautions are given regarding cleaning parts and using lifting devices due to components weighing up to 550 kg.
The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, shafts, carriers, and planetary gears. Tools needed are listed. Detailed illustrations accompany each step to show how to remove each component. Cleanliness is emphasized to prevent dirt from entering during disassembly.
The document provides step-by-step instructions to disassemble a final drive assembly. It begins by positioning the final drive on a repair stand and removing bolts and covers. Then various gears, shafts, seals and housings are dismantled. Disassembly includes pressing components out of carrier assemblies and using punches to remove pins from shafts. The process separates the sprocket housing from the motor housing and removes more than 30 individual parts.
The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Various components are then removed in order, including the cover, gears, shafts, carriers, pins and seals. Detailed illustrations accompany each step to show how to position lifting devices and tools. The process involves disassembling the planetary gears, carriers and housing sections to access all parts.
The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, shafts, carriers, and planetary gears. Tools needed are listed. Detailed illustrations accompany each step to show how to remove each component. Cleanliness is emphasized to prevent dirt from entering during disassembly.
The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, shafts, carriers, and planetary gears. Tools needed are listed. Detailed illustrations accompany each step to show how to remove each component. Cleanliness is emphasized to prevent dirt from entering during disassembly.
Caterpillar cat 323 e ln excavator (prefix rap) service repair manual (rap000...fikkskmmdm
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It details the disassembly and assembly procedures, including removing and installing the various components of the final drive such as the carrier assembly, ring gears, planetary gears, seals, and bearings. Precise instructions are provided for tasks like loosening bolts in a specific sequence, applying sealant, measuring clearances, and setting bearing preloads to ensure proper reassembly.
Caterpillar cat 323 e l excavator (prefix rap) service repair manual (rap0000...fikkskkdmmd
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides assembly instructions and specifies torque values and tools needed. Proper cleaning, application of sealant and anti-seize compound, and bearing preload are emphasized for correct reassembly.
The document provides step-by-step instructions to disassemble a final drive assembly. It involves removing over 30 individual parts in a specific sequence, including covers, gears, shafts, seals, washers, and housings. Various tools are required to remove retaining rings, pins, bolts and separate connected pieces. Precautions are given regarding cleaning parts and using lifting devices due to components weighing up to 550 kg.
The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, shafts, carriers, and planetary gears. Tools needed are listed. Detailed illustrations accompany each step to show how to remove each component. Cleanliness is emphasized to prevent dirt from entering during disassembly.
The document provides step-by-step instructions to disassemble a final drive assembly. It begins by positioning the final drive on a repair stand and removing bolts and covers. Then various gears, shafts, seals and housings are dismantled. Disassembly includes pressing components out of carrier assemblies and using punches to remove pins from shafts. The process separates the sprocket housing from the motor housing and removes more than 30 individual parts.
The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Various components are then removed in order, including the cover, gears, shafts, carriers, pins and seals. Detailed illustrations accompany each step to show how to position lifting devices and tools. The process involves disassembling the planetary gears, carriers and housing sections to access all parts.
The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, shafts, carriers, and planetary gears. Tools needed are listed. Detailed illustrations accompany each step to show how to remove each component. Cleanliness is emphasized to prevent dirt from entering during disassembly.
The document provides step-by-step instructions for disassembling the final drive of a 329DL excavator. It begins by removing the final drive assembly and placing it on a repair stand. Key steps include removing the cover, gears, shafts, carriers, and planetary gears. Tools needed are listed. Detailed illustrations accompany each step to show how to remove each component. Cleanliness is emphasized to prevent dirt from entering during disassembly.
Caterpillar cat 323 e ln excavator (prefix rap) service repair manual (rap000...fikkskmmdm
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It details the disassembly and assembly procedures, including removing and installing the various components of the final drive such as the carrier assembly, ring gears, planetary gears, seals, and bearings. Precise instructions are provided for tasks like loosening bolts in a specific sequence, applying sealant, measuring clearances, and setting bearing preloads to ensure proper reassembly.
Caterpillar cat 323 e l excavator (prefix rap) service repair manual (rap0000...fikkskkdmmd
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides assembly instructions and specifies torque values and tools needed. Proper cleaning, application of sealant and anti-seize compound, and bearing preload are emphasized for correct reassembly.
Caterpillar cat 323 e l excavator (prefix rap) service repair manual (rap0000...fikkskmmdm
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It details the disassembly and assembly procedures, including removing and installing the various components of the final drive such as the carrier assembly, ring gears, planetary gears, seals, and bearings. Precise instructions are given for tasks like loosening bolts in a specific sequence, applying sealant, measuring clearances, and setting bearing preloads to ensure correct reassembly.
Caterpillar cat 323 e sa excavator (prefix rap) service repair manual (rap000...ddkkddm
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides assembly instructions and specifies torque values and tools needed. Proper cleaning, application of sealant and anti-seize compound, and alignment of pins and bolts is emphasized for correct reassembly.
Caterpillar Cat 323E SA Excavator (Prefix RAP) Service Repair Manual (RAP0000...jdjkskmikdkmd
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes steps to disassemble and remove the final drive components, including the cover, carrier assemblies, ring gears, and seals. It also provides assembly instructions, specifying torque values and procedures for installing components like the bearings, seals, gears, and carrier assemblies back into the final drive housing. Tools required are listed. Detailed illustrations supplement the text instructions.
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and assembling the final drive components. The key steps are:
1. Remove the final drive from the excavator and disassemble its components, including the carrier assembly, ring gears, sun gears, and planetary gears.
2. Clean and inspect all parts, replacing any worn components.
3. Assemble the carrier assembly and other components in reverse order, applying anti-seize compound and torqueing bolts to the specified values.
4. Install the final drive back onto the excavator, ensuring proper alignment of parts
Caterpillar Cat 323E L Excavator (Prefix RAP) Service Repair Manual (RAP00001...jdjkskmikdkmd
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides instructions for reassembling these components, including installing seals, bearings, and gears, and adjusting preload on the bearings. Torque specifications and required tools are listed.
Caterpillar cat 323 e sa excavator (prefix rap) service repair manual (rap000...fikkskkdmmd
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides instructions for reassembling these components, including installing seals, bearings, and gears, and adjusting preload on the bearings. Torque specifications and required tools are listed.
CLAAS DOMINATOR 86 (Type 087) Combine Service Repair Manual.pdfudjkdksmmd
This document provides specifications for the CLAAS Dominator 106 combine harvester, including technical data, dimensions, weights, settings, capacities, and descriptions of components. Key details include the cutterbar widths ranging from 3.90 to 7.50 meters, overall machine width of 5565 to 9225 mm depending on cutterbar size, 6500 liter grain tank capacity, 151 kW six-cylinder engine, hydrostatic three-gear transmission for forward and reverse travel, and hydraulic brakes and steering. Dimensional drawings show the harvester in operating and transport positions.
CLAAS DOMINATOR 88 (Type 092) Combine Service Repair Manual.pdfudjkdksmmd
This document provides specifications for the CLAAS Dominator 106 combine harvester including technical data, dimensions, weights, settings, and capacities. It includes information on the cutterbar, threshing equipment, straw walkers, cleaning system, engines, transmission, hydraulics, electrical system, and auxiliary equipment. Dimensions and specifications are provided for operating and transport positions. Settings such as hydraulic oil pressures, tire pressures, and wheel bolt torques are also listed. The document contains detailed technical specifications for the CLAAS Dominator 106 combine harvester model.
CLAAS DOMINATOR 78H (Type 079) Combine Service Repair Manual.pdfudjkdksmmd
This document provides specifications for the CLAAS Dominator 106 combine harvester, including technical data, dimensions, weights, settings, capacities, and descriptions of components. Key details include the cutterbar widths of 3.90-7.50 meters, overall transport width of 4365-8025 mm depending on cutterbar size, 6500 liter grain tank capacity, 151 kW six-cylinder engine, hydrostatic ground drive with variable speeds up to 20 km/h, and straw walker system with six racks and two crankshafts for separation and cleaning.
CLAAS DOMINATOR 76 (Type 084) Combine Service Repair Manual.pdfudjkdksmmd
This document provides specifications for the CLAAS Dominator 106 combine harvester, including technical data, dimensions, weights, settings, capacities, and descriptions of components. Key details include the cutterbar widths ranging from 3.90 to 7.50 meters, overall machine width of 5565 to 9225 mm depending on cutterbar size, transport width of 4365 to 8025 mm, length of 7770 to 10640 mm, and empty weight ranging from 9060 kg to over 17,000 kg fully equipped. Engine specifications, hydraulic pressures, oil capacities, and other technical details are also listed.
CLAAS DOMINATOR 78 (Type 091) Combine Service Repair Manual.pdfudjkdksmmd
This document provides specifications for the CLAAS Dominator 106 combine harvester including technical data, dimensions, weights, settings, and capacities. It includes information on the cutterbar, threshing equipment, straw walkers, cleaning system, engines, transmission, hydraulics, electrical system, and auxiliary equipment. Dimensions and specifications are provided for operating and transport positions. Settings such as hydraulic oil pressures, reel speeds, and concave clearances are also listed. The document contains detailed technical information about the components and configurations of the CLAAS Dominator 106 combine.
The document provides disassembly instructions for the final drive carriers, hubs, and brakes of the front and rear axles of a M322D wheeled excavator. It lists the required tools and presents step-by-step instructions with accompanying illustrations to remove components such as carrier housings, planetary gears, ring gear housings, pistons, discs, seals, bearings, and hubs. Safety notices are included to warn of risks from released pressures and springs.
This document provides instructions for disassembling and assembling the front and rear axles of a M322D MH wheeled excavator. It details 22 steps for disassembling the front axle, removing components like carrier housings, gears, seals, bearings and pistons. It then provides 23 steps for reassembling the front axle in reverse order. A similar level of detail is given for the 23 step disassembly and 22 step assembly of the rear axle. Precautions and required specialty tools are also listed.
This document provides disassembly instructions for the front and rear axles, carriers, hubs, and brakes of an M322C wheeled excavator. The front axle disassembly procedure involves 41 steps to remove components like the carrier housing, planetary gears, ring gear assembly, hub assembly, and spindle components. The rear axle disassembly involves 27 steps including removing the brake drum, gear assemblies, axle, hub assembly, dust shield, brake assembly, and spindle. Detailed illustrations are provided to identify each part and tooling required is listed.
The document provides instructions for disassembling and assembling the front axle of a M322D MH Wheeled Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the carrier housing, planetary gears, bearings, seals, and brake discs. Reassembly instructions are also provided, with steps like installing bearings, seals, and torque specifications.
This document provides instructions for disassembling and assembling the swing drive of a M322C wheeled excavator. It describes 28 steps to disassemble the swing drive into individual components such as gears, shafts, bearings, seals and housing. It also lists the required tools. The assembly procedure is described in reverse order, with precautions noted for installing components with spring tension.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then lists 21 steps for reassembling the swing drive components in reverse order. Precautions and special tools required are listed. Lubrication and cleaning of parts is emphasized prior to assembly.
This document provides instructions for disassembling and assembling the swing drive of an M318C wheeled excavator. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and lifting out the swing drive unit. Disassembly of the swing drive further requires removing retaining rings, plates, discs, seals, gears, and bearings. Reassembly follows the reverse order, applying lubricant to components and setting proper torque specifications. Tools and safety precautions are also listed.
This document provides instructions for disassembling and assembling the swing drive of an M318D MH wheeled excavator. The disassembly procedure involves removing 28 parts from the swing drive assembly including discs, plates, pistons, seals, gears, and bearings. The assembly procedure instructs installing these same parts in reverse order and adjusting bearing preloads to specified torque values using various tools. Proper cleaning and lubrication of parts is emphasized.
This document provides instructions for disassembling and assembling the travel motor of an M318C Wheeled Excavator. It lists 48 steps to fully disassemble the travel motor by removing components like valves, springs, seals, plugs and housing parts. The assembly section lists 21 steps to reassemble the components in the reverse order, making sure to clean parts thoroughly and apply proper torque to bolts. Precautions are provided to watch out for spring loaded components. Tools required are also listed.
This document provides assembly instructions for the front axle final drive carriers, hubs, and brakes of a M318C Wheeled Excavator. It outlines 41 steps to disassemble and assemble these components, including removing retaining rings, planetary gears, seals, and bearings from housings and hubs. Precise torque specifications are provided for reinstalling components like spanner nuts to ensure proper rolling torque of roller bearings. Cleanliness is emphasized throughout to prevent damage to precision parts during reassembly.
This document provides instructions for assembling the swing drive of a M318C Wheeled Excavator. It describes 28 steps for installing various components like bearings, seals, gears, and plates. It specifies torque values and tolerances for tightening nuts. Dimensional checks are outlined to ensure the assembled swing brake travel is within the specified range of 1.1 to 1.4 mm. Proper cleaning, lubrication and tooling are emphasized to complete the assembly correctly.
More Related Content
Similar to Caterpillar Cat 329DL EXCAVATOR (Prefix MNB) Service Repair Manual (MNB00001 and up).pdf
Caterpillar cat 323 e l excavator (prefix rap) service repair manual (rap0000...fikkskmmdm
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It details the disassembly and assembly procedures, including removing and installing the various components of the final drive such as the carrier assembly, ring gears, planetary gears, seals, and bearings. Precise instructions are given for tasks like loosening bolts in a specific sequence, applying sealant, measuring clearances, and setting bearing preloads to ensure correct reassembly.
Caterpillar cat 323 e sa excavator (prefix rap) service repair manual (rap000...ddkkddm
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides assembly instructions and specifies torque values and tools needed. Proper cleaning, application of sealant and anti-seize compound, and alignment of pins and bolts is emphasized for correct reassembly.
Caterpillar Cat 323E SA Excavator (Prefix RAP) Service Repair Manual (RAP0000...jdjkskmikdkmd
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes steps to disassemble and remove the final drive components, including the cover, carrier assemblies, ring gears, and seals. It also provides assembly instructions, specifying torque values and procedures for installing components like the bearings, seals, gears, and carrier assemblies back into the final drive housing. Tools required are listed. Detailed illustrations supplement the text instructions.
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and assembling the final drive components. The key steps are:
1. Remove the final drive from the excavator and disassemble its components, including the carrier assembly, ring gears, sun gears, and planetary gears.
2. Clean and inspect all parts, replacing any worn components.
3. Assemble the carrier assembly and other components in reverse order, applying anti-seize compound and torqueing bolts to the specified values.
4. Install the final drive back onto the excavator, ensuring proper alignment of parts
Caterpillar Cat 323E L Excavator (Prefix RAP) Service Repair Manual (RAP00001...jdjkskmikdkmd
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides instructions for reassembling these components, including installing seals, bearings, and gears, and adjusting preload on the bearings. Torque specifications and required tools are listed.
Caterpillar cat 323 e sa excavator (prefix rap) service repair manual (rap000...fikkskkdmmd
This document provides instructions for servicing the final drive of excavator models 323E L, 323E LN, and 323E SA. It includes procedures for disassembling and removing components like the final drive, carrier assembly, ring gears, and seals. It also provides instructions for reassembling these components, including installing seals, bearings, and gears, and adjusting preload on the bearings. Torque specifications and required tools are listed.
Similar to Caterpillar Cat 329DL EXCAVATOR (Prefix MNB) Service Repair Manual (MNB00001 and up).pdf (6)
CLAAS DOMINATOR 86 (Type 087) Combine Service Repair Manual.pdfudjkdksmmd
This document provides specifications for the CLAAS Dominator 106 combine harvester, including technical data, dimensions, weights, settings, capacities, and descriptions of components. Key details include the cutterbar widths ranging from 3.90 to 7.50 meters, overall machine width of 5565 to 9225 mm depending on cutterbar size, 6500 liter grain tank capacity, 151 kW six-cylinder engine, hydrostatic three-gear transmission for forward and reverse travel, and hydraulic brakes and steering. Dimensional drawings show the harvester in operating and transport positions.
CLAAS DOMINATOR 88 (Type 092) Combine Service Repair Manual.pdfudjkdksmmd
This document provides specifications for the CLAAS Dominator 106 combine harvester including technical data, dimensions, weights, settings, and capacities. It includes information on the cutterbar, threshing equipment, straw walkers, cleaning system, engines, transmission, hydraulics, electrical system, and auxiliary equipment. Dimensions and specifications are provided for operating and transport positions. Settings such as hydraulic oil pressures, tire pressures, and wheel bolt torques are also listed. The document contains detailed technical specifications for the CLAAS Dominator 106 combine harvester model.
CLAAS DOMINATOR 78H (Type 079) Combine Service Repair Manual.pdfudjkdksmmd
This document provides specifications for the CLAAS Dominator 106 combine harvester, including technical data, dimensions, weights, settings, capacities, and descriptions of components. Key details include the cutterbar widths of 3.90-7.50 meters, overall transport width of 4365-8025 mm depending on cutterbar size, 6500 liter grain tank capacity, 151 kW six-cylinder engine, hydrostatic ground drive with variable speeds up to 20 km/h, and straw walker system with six racks and two crankshafts for separation and cleaning.
CLAAS DOMINATOR 76 (Type 084) Combine Service Repair Manual.pdfudjkdksmmd
This document provides specifications for the CLAAS Dominator 106 combine harvester, including technical data, dimensions, weights, settings, capacities, and descriptions of components. Key details include the cutterbar widths ranging from 3.90 to 7.50 meters, overall machine width of 5565 to 9225 mm depending on cutterbar size, transport width of 4365 to 8025 mm, length of 7770 to 10640 mm, and empty weight ranging from 9060 kg to over 17,000 kg fully equipped. Engine specifications, hydraulic pressures, oil capacities, and other technical details are also listed.
CLAAS DOMINATOR 78 (Type 091) Combine Service Repair Manual.pdfudjkdksmmd
This document provides specifications for the CLAAS Dominator 106 combine harvester including technical data, dimensions, weights, settings, and capacities. It includes information on the cutterbar, threshing equipment, straw walkers, cleaning system, engines, transmission, hydraulics, electrical system, and auxiliary equipment. Dimensions and specifications are provided for operating and transport positions. Settings such as hydraulic oil pressures, reel speeds, and concave clearances are also listed. The document contains detailed technical information about the components and configurations of the CLAAS Dominator 106 combine.
The document provides disassembly instructions for the final drive carriers, hubs, and brakes of the front and rear axles of a M322D wheeled excavator. It lists the required tools and presents step-by-step instructions with accompanying illustrations to remove components such as carrier housings, planetary gears, ring gear housings, pistons, discs, seals, bearings, and hubs. Safety notices are included to warn of risks from released pressures and springs.
This document provides instructions for disassembling and assembling the front and rear axles of a M322D MH wheeled excavator. It details 22 steps for disassembling the front axle, removing components like carrier housings, gears, seals, bearings and pistons. It then provides 23 steps for reassembling the front axle in reverse order. A similar level of detail is given for the 23 step disassembly and 22 step assembly of the rear axle. Precautions and required specialty tools are also listed.
This document provides disassembly instructions for the front and rear axles, carriers, hubs, and brakes of an M322C wheeled excavator. The front axle disassembly procedure involves 41 steps to remove components like the carrier housing, planetary gears, ring gear assembly, hub assembly, and spindle components. The rear axle disassembly involves 27 steps including removing the brake drum, gear assemblies, axle, hub assembly, dust shield, brake assembly, and spindle. Detailed illustrations are provided to identify each part and tooling required is listed.
The document provides instructions for disassembling and assembling the front axle of a M322D MH Wheeled Excavator. It lists the required tools and gives step-by-step instructions to remove components such as the carrier housing, planetary gears, bearings, seals, and brake discs. Reassembly instructions are also provided, with steps like installing bearings, seals, and torque specifications.
This document provides instructions for disassembling and assembling the swing drive of a M322C wheeled excavator. It describes 28 steps to disassemble the swing drive into individual components such as gears, shafts, bearings, seals and housing. It also lists the required tools. The assembly procedure is described in reverse order, with precautions noted for installing components with spring tension.
This document provides instructions for disassembling and assembling the swing drive of an M322C wheeled excavator. It begins with 28 steps to disassemble the swing drive components. This includes removing retaining rings, springs, discs, plates, seals, bearings, and gears. It then lists 21 steps for reassembling the swing drive components in reverse order. Precautions and special tools required are listed. Lubrication and cleaning of parts is emphasized prior to assembly.
This document provides instructions for disassembling and assembling the swing drive of an M318C wheeled excavator. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and lifting out the swing drive unit. Disassembly of the swing drive further requires removing retaining rings, plates, discs, seals, gears, and bearings. Reassembly follows the reverse order, applying lubricant to components and setting proper torque specifications. Tools and safety precautions are also listed.
This document provides instructions for disassembling and assembling the swing drive of an M318D MH wheeled excavator. The disassembly procedure involves removing 28 parts from the swing drive assembly including discs, plates, pistons, seals, gears, and bearings. The assembly procedure instructs installing these same parts in reverse order and adjusting bearing preloads to specified torque values using various tools. Proper cleaning and lubrication of parts is emphasized.
This document provides instructions for disassembling and assembling the travel motor of an M318C Wheeled Excavator. It lists 48 steps to fully disassemble the travel motor by removing components like valves, springs, seals, plugs and housing parts. The assembly section lists 21 steps to reassemble the components in the reverse order, making sure to clean parts thoroughly and apply proper torque to bolts. Precautions are provided to watch out for spring loaded components. Tools required are also listed.
This document provides assembly instructions for the front axle final drive carriers, hubs, and brakes of a M318C Wheeled Excavator. It outlines 41 steps to disassemble and assemble these components, including removing retaining rings, planetary gears, seals, and bearings from housings and hubs. Precise torque specifications are provided for reinstalling components like spanner nuts to ensure proper rolling torque of roller bearings. Cleanliness is emphasized throughout to prevent damage to precision parts during reassembly.
This document provides instructions for assembling the swing drive of a M318C Wheeled Excavator. It describes 28 steps for installing various components like bearings, seals, gears, and plates. It specifies torque values and tolerances for tightening nuts. Dimensional checks are outlined to ensure the assembled swing brake travel is within the specified range of 1.1 to 1.4 mm. Proper cleaning, lubrication and tooling are emphasized to complete the assembly correctly.
1) The document provides assembly and disassembly instructions for a gear motor and control valve used in a wheeled excavator.
2) The gear motor assembly instructions include installing bearings, seals, gears, and housing components in 12 steps.
3) The control valve disassembly instructions describe removing 33 parts in 12 steps, taking care with springs that could cause injury.
This document provides instructions for disassembling and assembling the rear axle of a M316C Wheeled Excavator. The disassembly procedure involves removing 23 components of the rear axle including the carrier housing, planetary gears, retaining rings, and hub. The assembly procedure describes installing these 23 components in reverse order and includes steps to measure clearances and install seals, bearings, and thrust washers correctly. Tools required are also listed.
This document provides instructions for disassembling and assembling the swing drive of an excavator model M318C MH. It lists required tools and gives step-by-step procedures for removing and installing over 30 individual parts. Proper cleaning and lubrication of parts is emphasized. Detailed illustrations accompany each step to ensure correct assembly. Safety warnings are provided for steps involving spring tension or press operations.
The document provides disassembly instructions for a piston pump (swing) in 3 sentences:
It outlines 49 steps to fully disassemble the piston pump, including removing components like the servo valve, charge pump, head, pistons, barrel assembly, swashplate assembly, shafts, seals, springs, and other internal parts. Special tools are required to compress springs and remove retaining rings safely. Cleanliness is important and parts should be marked for proper reinstallation.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
2. 3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
Illustration 3 g00708091
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
4/12
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engine...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 4 g00708235
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
Illustration 5 g00708092
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
Illustration 6 g01304883
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
5/12
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engine...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 7 g00708144
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
Illustration 8 g00708218
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
6/12
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engine...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 9 g00708162
13. Remove sun gear (14) from carrier assembly (15).
Illustration 10 g00708325
14. Remove spacer (16).
Illustration 11 g00708184
Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
7/12
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engine...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 12 g00708360
16. Use a screwdriver or a chisel in order to separate the two ring gears (17).
Note: The two ring gears are held together with Tooling (F). It may be necessary to heat the
ring gears in order to soften the sealant. Do not heat over 135 °C (275 °F) for more than
thirty minutes.
Illustration 13 g00708172
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
Illustration 14 g00708175
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
8/12
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engine...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 15 g00708370
Illustration 16 g00708220
b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
9/12
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engine...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 17 g00708186
22. Remove O-ring seal (24) from main housing (18).
Illustration 18 g00708187
23. Remove bolts (25) from gear (26).
Illustration 19 g00708202
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from the main housing (18) once gear (26) is
removed. Make sure that the motor housing is supported.
10/12
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engi...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 20 g00708211
25. Remove shims (27) from the main housing.
Illustration 21 g00708212
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from the motor housing (28). The combined weight of main housing (18) and the
final drive sprocket is approximately 82 kg (180 lb).
Illustration 22 g00708214
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
11/12
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engi...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 23 g00708215
Illustration 24 g00708216
30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Mar 3 23:41:49 UTC+0800 2020
12/12
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engi...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 138-7575 Link Bracket 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G 138-7576 Link Bracket 2
Start By:
a. Start by removing the final drive. Refer to Disassembly and Assembly, "Final Drive -
Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled to the original locations.
Illustration 1 g00892878
2. Use Tooling (G) and a suitable lifting device to position the final drive assembly onto
Tooling (A). The weight of the final drive assembly is approximately 550 kg (1200 lb).
3. Remove bolts (1).
3/13
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engine...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 2 g00892883
4. Use Tooling (B) and a suitable lifting device to remove cover (2). The weight of cover (2) is
approximately 32 kg (70 lb).
Illustration 3 g00892888
5. Remove bolts (3) and gear (4). Check plate (6). Replace plate (6) if plate (6) is worn.
Remove plugs (5) from cover (2).
Illustration 4 g00892906
6. Remove O-ring seals (7) from plugs (5).
4/13
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engine...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 5 g00892930
7. Remove gear (8) and spacer (9).
Illustration 6 g00892965
8. Use Tooling (C) to remove retaining ring (10). Remove washer (11) and gear (12). Remove
bearing assembly (13) and washer (14).
9. Repeat Step 8 for the other two gear assemblies.
Illustration 7 g00892968
10. Remove retaining ring (15).
5/13
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engine...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 8 g00892975
11. Remove carrier assembly (16).
Illustration 9 g01389804
12. Use a suitable press to remove the shafts from carrier assembly (16).
Illustration 10 g00892977
6/13
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engine...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. 13. Remove gear (17) and spacer (18).
Illustration 11 g00892997
14. Use Tooling (D) and a suitable lifting device to remove planetary carrier (19). The weight of
planetary carrier (19) is approximately 48 kg (105 lb).
Illustration 12 g00893019
15. Remove retaining ring (21). Lift planetary carrier (19) off sun gear (20).
Illustration 13 g00896860
16. Drive spring pin (23) into planetary shaft (22).
7/13
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engine...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 14 g00893043
17. Remove planetary shaft (22). Use a suitable punch to remove spring pin (23) from planetary
shaft (22).
Illustration 15 g00896863
18. Remove washers (24) and bearing (25) from planetary gear (26).
19. Repeat Steps 16 through 18 for the other two planetary gears.
Illustration 16 g01842853
20. Remove gear (27). Remove spacer (27A).
8/13
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engine...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 17 g01842974
21. Use two people to remove carrier assembly (28). The weight of carrier assembly (28) is
approximately 38 kg (85 lb).
Illustration 18 g01843140
22. Drive spring pin (30) into shaft (29).
Illustration 19 g00893658
23. Remove shaft (29). Use a suitable punch to remove spring pin (30) from shaft (29).
9/13
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engine...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 20 g00893674
24. Remove washers (31) and bearings (32) from planetary gear (33).
25. Repeat Steps 22 through 24 for the other three planetary gears.
Illustration 21 g01208300
26. Fasten Tooling (E) and a suitable lifting device to ring gear (34), as shown. Remove ring
gear (34) from sprocket housing (35). The weight of ring gear (34) is approximately 66 kg
(146 lb).
Illustration 22 g01208542
10/13
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engi...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. 27. Remove O-ring seal (36) from sprocket housing (35).
Illustration 23 g01208553
28. Remove bolts (37) from coupling gear (38).
Illustration 24 g01208572
29. Install suitable forcing bolts (39) in coupling gear (38). Tighten the forcing bolts evenly in
order to loosen coupling gear (38). Remove the coupling gear from the motor housing.
Illustration 25 g01208578
11/13
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engi...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
21. Illustration 26 g01208625
30. Remove shims (40) from the motor housing.
Note: Inner cones and outer bearing cones (42) are a slip fit on the motor housing. While
you remove sprocket housing (35) from the motor housing, inner bearing cone (42) may
stay with the sprocket housing or the inner bearing cone may stay on the motor housing.
31. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Separate the
sprocket housing from the motor housing. The weight of sprocket housing (35) is
approximately 109 kg (240 lb).
Illustration 27 g01208626
32. Remove the locating pins from the motor housing.
33. Remove Duo-Cone seal (41) from the motor housing.
34. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.
12/13
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engi...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 28 g01208633
35. Remove Duo-Cone seal (43) from the sprocket housing.
36. If inner bearing cone (42) remained on the sprocket housing, then remove the inner bearing
cone.
37. Remove the bearing cups from the sprocket housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Mar 3 23:42:45 UTC+0800 2020
13/13
329D & 329D L Excavators MNB00001-UP (MACHINE) POWERED BY C7 Engi...
2020/3/3
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...