This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavator models. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, seals and housing cover. Corresponding assembly instructions are also provided, specifying the use of various tools and noting that all seals and gaskets must be replaced. Cleanliness is emphasized throughout the assembly process.
Caterpillar cat 326 d2 l excavator (prefix kgy) service repair manual (kgy000...fjsjekkmdmme
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavators. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, friction discs, and seals. The assembly procedure instructs putting the travel motor back together and notes that all O-rings and gaskets must be replaced and components should be cleaned before assembly. Proper alignment of parts is important during assembly.
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavators. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, friction discs, and seals. The assembly procedure instructs putting the travel motor back together in the reverse order and notes the importance of cleanliness, applying lubricant to parts, and ensuring correct alignment of components.
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the head, bearings, brake piston, seals, and housing cover. Corresponding assembly instructions are also provided, including applying thread lock compound and ensuring proper alignment of parts. Cleanliness is emphasized throughout the process.
Caterpillar cat 326 d2 l excavator (prefix mgw) service repair manual (mgw000...fjjskdmnenemm
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the head, port plate, bearings, brake piston, seals, plates, springs and retaining rings. Corresponding assembly instructions are also provided, including applying thread lock compound and ensuring proper alignment of keys and notches. Cleanliness is emphasized throughout the process.
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove and install over 25 components of the travel motor. Cleanliness is emphasized during disassembly and assembly. Several components, like pistons and springs, must be returned to their original positions.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...jdkskmdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using tools to install the bushing, idler shaft, idler gear, thrust plate, washer, and idler gear bolt while ensuring proper gear alignment and backlash. Tolerances for backlash and clearances are provided.
This document provides instructions for disassembling and assembling the travel motor of 324E and 324E LN excavators. The disassembly process involves removing 28 components from the travel motor in 27 steps. The assembly process reverses the disassembly with 28 steps and provides guidance on cleaning, lubricating, and installing components in the correct orientation. Tools required include retaining ring pliers, drivers, pullers, and adapters to securely hold components during disassembly and assembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations guide removal of additional components like the flywheel housing, crankshaft pulley, and crankshaft front seal. Tools and safety precautions are also listed.
Caterpillar cat 326 d2 l excavator (prefix kgy) service repair manual (kgy000...fjsjekkmdmme
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavators. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, friction discs, and seals. The assembly procedure instructs putting the travel motor back together and notes that all O-rings and gaskets must be replaced and components should be cleaned before assembly. Proper alignment of parts is important during assembly.
This document provides instructions for disassembling and assembling the travel motor of 326D2 and 326D2 L excavators. The disassembly procedure involves removing 28 different components of the travel motor including the head, port plate, bearings, brake piston, plates, friction discs, and seals. The assembly procedure instructs putting the travel motor back together in the reverse order and notes the importance of cleanliness, applying lubricant to parts, and ensuring correct alignment of components.
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the head, bearings, brake piston, seals, and housing cover. Corresponding assembly instructions are also provided, including applying thread lock compound and ensuring proper alignment of parts. Cleanliness is emphasized throughout the process.
Caterpillar cat 326 d2 l excavator (prefix mgw) service repair manual (mgw000...fjjskdmnenemm
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the head, port plate, bearings, brake piston, seals, plates, springs and retaining rings. Corresponding assembly instructions are also provided, including applying thread lock compound and ensuring proper alignment of keys and notches. Cleanliness is emphasized throughout the process.
The document provides instructions for disassembling and assembling the travel motor of a 326D2 or 326D2 L excavator. It lists the required tools and gives step-by-step procedures to remove and install over 25 components of the travel motor. Cleanliness is emphasized during disassembly and assembly. Several components, like pistons and springs, must be returned to their original positions.
Caterpillar Cat 312D L Excavator (Prefix RHL) Service Repair Manual (RHL00001...jdkskmdmdm
This document provides instructions for removing and installing the idler gear in the front gear group of a C4.2 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing, and idler shaft. The installation procedure specifies cleaning parts and using tools to install the bushing, idler shaft, idler gear, thrust plate, washer, and idler gear bolt while ensuring proper gear alignment and backlash. Tolerances for backlash and clearances are provided.
This document provides instructions for disassembling and assembling the travel motor of 324E and 324E LN excavators. The disassembly process involves removing 28 components from the travel motor in 27 steps. The assembly process reverses the disassembly with 28 steps and provides guidance on cleaning, lubricating, and installing components in the correct orientation. Tools required include retaining ring pliers, drivers, pullers, and adapters to securely hold components during disassembly and assembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 314D CR excavator, including:
1) Removing the idler gear from the front gear group by removing the bolt and washer securing it to the idler shaft and pulling it off using a puller tool.
2) Instructions specify ensuring timing marks are aligned before removal to maintain proper timing of gears.
3) Detailed steps and illustrations guide removal of additional components like the flywheel housing, crankshaft pulley, and crankshaft front seal. Tools and safety precautions are also listed.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, counterbalance valve housing assembly, and more. Safety notices are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, wrenches, and other equipment.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...jdkskmdmdm
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like bolts, covers, seals, springs, pistons, gears, and bearings. The corresponding 51 steps for assembly install these same components in reverse order, noting the tools required and proper installation of seals, bearings, and retaining rings. Precautions are included for released spring forces during disassembly and heating components during assembly.
Caterpillar Cat 330F L Excavator (Prefix GHT) Service Repair Manual (GHT00001...jdkskmdmdm
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and ensuring fluids are contained.
This document provides assembly instructions for repairing a hydraulic pump in 3 steps:
1. Install various internal components like bearings, seals, and pistons into the pump housing.
2. Attach the pump housing to the pump head and install additional external components.
3. Assemble the pump control mechanism by installing springs, pistons, and covers.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing using specialized tools over 30 detailed steps. Cleanliness is emphasized throughout to prevent dirt contamination during reassembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1. The flywheel, flywheel housing, crankshaft rear seal, and vibration damper and pulley. Tools and torque specifications are listed for each procedure.
2. Removing the crankshaft rear seal involves drilling holes in the seal and pulling it out with a slide hammer tool. Installing the new seal uses a seal installation tool.
3. Removing the flywheel housing first requires removing mounting bolts and the flywheel. Installing applies sealant and mounts the housing with bolts.
4. Instructions are provided to remove the crankshaft front
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precise tools and cleaning of parts is emphasized.
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs technicians to clean all parts thoroughly, apply lubricants where specified, and install over 30 parts into the final drive housing in the reverse order of disassembly using various tools. Technicians are advised to replace all seals, gaskets and O-rings during assembly and to keep all parts clean.
The document provides instructions for disassembling and assembling the piston motor (hydraulic fan) on 325C and 325C L excavator models. The disassembly procedure involves 22 steps to remove components like the key, cover, port plate, bearings, plugs, sleeves, pistons and housing. The assembly procedure describes 16 steps including pressing components, installing seals, pins and rings in the proper order and orientation to rebuild the piston motor. Cleanliness and applying a light oil film to parts is emphasized throughout.
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
This document provides instructions for removing and installing various components of the crankshaft and flywheel housing on a 325C Excavator. It describes how to remove and install the flywheel, crankshaft rear seal, rear seal carrier, and flywheel housing. The procedures include lists of required tools and step-by-step instructions describing how to remove each component and install the replacement parts. Safety notices are provided to keep parts clean and contain fluids appropriately during the repair work.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...jdkskmdmdm
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists the required tools and outlines 16 steps to disassemble parts like the traction control valve, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
1) The document provides disassembly instructions for components of a 313D excavator including the final drive, travel motor, counterbalance valve, and traction control valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification marks and order of components.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, plates, and seals. Proper handling and storage of fluids is also addressed.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...jdkskmdmdm
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, installing new gaskets, and tightening bolts in a specific sequence using torque wrenches and degree wheels to ensure proper torque.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...jdkskmdmdm
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like sprockets, valves, gears, plates, seals and more. Safety notices are included to warn of hazards like hydraulic pressure, heavy lifting, and released spring forces. The extensive instructions allow for complete disassembly of the specified systems for inspection or repair.
This document provides instructions for removing and installing a crankshaft rear seal on a 3054C engine. The removal procedure involves taking out setscrews and the housing assembly. For installation, a new pre-assembled seal and housing is used. It is pushed onto the crankshaft flange using a plastic sleeve for protection. Setscrews are then tightened to secure it after alignment. Proper cleaning, handling and lubrication of parts is emphasized to prevent damage.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) Drain coolant and oil, remove ancillary components, and loosen head bolts in a gradual, reverse sequence to prevent distortion.
2) Use lifting equipment to carefully remove the 57 kg cylinder head. Clean the head and block mating surfaces.
3) Install a new head gasket and guide bolts, then lower the head into place. Tighten bolts in stages to the specified torque values using a degree wheel.
4) Reinstall removed components, refill fluids, and complete additional specified tasks to finish the job.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar C4.2 engine. It describes:
1) Removing the electric starting motor, flywheel, and ring gear before removing the flywheel housing.
2) Using lifting tools to remove the flywheel housing bolts and separate the housing from the cylinder block.
3) Installing a new gasket and oil seal before reinstalling the flywheel housing with bolts and reattaching the flywheel and starting motor.
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists over 30 detailed steps to disassemble components like the final drive, travel motor barrel assembly, planetary gear assembly, counterbalance valve housing assembly, and more. Safety notices are provided throughout to warn of potential injuries from parts under spring tension or residual fluid pressure. Required tools include link brackets, a transmission repair stand, bolts, pullers, wrenches, and other equipment.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...jdkskmdmdm
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like bolts, covers, seals, springs, pistons, gears, and bearings. The corresponding 51 steps for assembly install these same components in reverse order, noting the tools required and proper installation of seals, bearings, and retaining rings. Precautions are included for released spring forces during disassembly and heating components during assembly.
Caterpillar Cat 330F L Excavator (Prefix GHT) Service Repair Manual (GHT00001...jdkskmdmdm
The document provides disassembly instructions for a 330F and 330F L excavator travel motor over 28 steps. It details removing components like the head, brake piston, rotating assembly, pistons, and seals. Tools include an adapter, nuts, threaded rod, eyebolts, drivers, and pullers. Safety notices warn of spring forces, pressurized air, and ensuring fluids are contained.
This document provides assembly instructions for repairing a hydraulic pump in 3 steps:
1. Install various internal components like bearings, seals, and pistons into the pump housing.
2. Attach the pump housing to the pump head and install additional external components.
3. Assemble the pump control mechanism by installing springs, pistons, and covers.
The document provides step-by-step instructions to disassemble a final drive assembly for excavator models 325D and 325D L. It begins by removing the final drive from the excavator and cleaning it. Then the cover is removed after fastening the final drive to a repair stand. Various internal components like gears, shafts, and seals are then dismantled from the housing using specialized tools over 30 detailed steps. Cleanliness is emphasized throughout to prevent dirt contamination during reassembly.
The document provides instructions for removing and installing various engine components on a Caterpillar 325D excavator including:
1. The flywheel, flywheel housing, crankshaft rear seal, and vibration damper and pulley. Tools and torque specifications are listed for each procedure.
2. Removing the crankshaft rear seal involves drilling holes in the seal and pulling it out with a slide hammer tool. Installing the new seal uses a seal installation tool.
3. Removing the flywheel housing first requires removing mounting bolts and the flywheel. Installing applies sealant and mounts the housing with bolts.
4. Instructions are provided to remove the crankshaft front
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator, including:
- Removing and installing the flywheel, which requires the use of lifting tools and torque wrenches.
- Removing the crankshaft rear seal using drilling and hammering tools, and removing any wear sleeves.
- Installing the new crankshaft rear seal with a seal installer tool.
- Additional procedures for removing and installing components like the vibration damper, pulley, flywheel housing and rear seal carrier. Precise tools and cleaning of parts is emphasized.
This document provides instructions for disassembling and assembling the final drive of 325C and 325C L excavator models. The disassembly procedure involves removing over 30 individual parts from the final drive housing in a specific sequence. The assembly procedure instructs technicians to clean all parts thoroughly, apply lubricants where specified, and install over 30 parts into the final drive housing in the reverse order of disassembly using various tools. Technicians are advised to replace all seals, gaskets and O-rings during assembly and to keep all parts clean.
The document provides instructions for disassembling and assembling the piston motor (hydraulic fan) on 325C and 325C L excavator models. The disassembly procedure involves 22 steps to remove components like the key, cover, port plate, bearings, plugs, sleeves, pistons and housing. The assembly procedure describes 16 steps including pressing components, installing seals, pins and rings in the proper order and orientation to rebuild the piston motor. Cleanliness and applying a light oil film to parts is emphasized throughout.
This document provides instructions for disassembling and assembling the travel motor of 324E L and 324E LN Excavator models. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing and installing components like the motor head, brake piston, rotating assembly, bearings, seals, and more. Precautions are included to properly handle springs and ensure correct positioning of parts.
This document provides instructions for removing and installing various components of the crankshaft and flywheel housing on a 325C Excavator. It describes how to remove and install the flywheel, crankshaft rear seal, rear seal carrier, and flywheel housing. The procedures include lists of required tools and step-by-step instructions describing how to remove each component and install the replacement parts. Safety notices are provided to keep parts clean and contain fluids appropriately during the repair work.
The document provides instructions for removing and installing various components of a Caterpillar C4.2 engine, including the flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures include using various tools to remove bolts, nuts, seals, and other parts. Technicians are advised to keep components clean and contain fluids properly during disassembly and reassembly.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...jdkskmdmdm
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists the required tools and outlines 16 steps to disassemble parts like the traction control valve, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluid.
1) The document provides disassembly instructions for components of a 313D excavator including the final drive, travel motor, counterbalance valve, and traction control valve.
2) It lists required tools and safety precautions and provides a step-by-step process to remove each part, noting identification marks and order of components.
3) Detailed illustrations accompany each step to show how to remove components like sprockets, valves, springs, gears, plates, and seals. Proper handling and storage of fluids is also addressed.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...jdkskmdmdm
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, installing new gaskets, and tightening bolts in a specific sequence using torque wrenches and degree wheels to ensure proper torque.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...jdkskmdmdm
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like sprockets, valves, gears, plates, seals and more. Safety notices are included to warn of hazards like hydraulic pressure, heavy lifting, and released spring forces. The extensive instructions allow for complete disassembly of the specified systems for inspection or repair.
This document provides instructions for removing and installing a crankshaft rear seal on a 3054C engine. The removal procedure involves taking out setscrews and the housing assembly. For installation, a new pre-assembled seal and housing is used. It is pushed onto the crankshaft flange using a plastic sleeve for protection. Setscrews are then tightened to secure it after alignment. Proper cleaning, handling and lubrication of parts is emphasized to prevent damage.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) Drain coolant and oil, remove ancillary components, and loosen head bolts in a gradual, reverse sequence to prevent distortion.
2) Use lifting equipment to carefully remove the 57 kg cylinder head. Clean the head and block mating surfaces.
3) Install a new head gasket and guide bolts, then lower the head into place. Tighten bolts in stages to the specified torque values using a degree wheel.
4) Reinstall removed components, refill fluids, and complete additional specified tasks to finish the job.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326D2 EXCAVATOR KGY
Configuration: 326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03124522
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded RodM12 x 1.75 by 250 mm (10 in) long 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
A. Remove the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Remove".
1/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
Spring force can cause personal injury or death.
Do not repair until you have read the Operation and Maintenance
Manual.
2/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 4. Remove bolts (1) .
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00887302
6. Remove O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 3 g00887311
7. Remove O-ring seals (6) . Remove springs (7) .
3/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B) .
8. Place a shop towel over brake piston (8) . Retain brake piston (8) with Tooling (B) . Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y) . Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
4/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g00887336
9. Remove seal (9) and backup ring (10) from the brake piston.
10. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
11. Remove plates (13) and friction discs (14) .
Illustration 8 g00887401
5/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 9 g00887405
12. Install Tooling (C) into shaft (15) . Use a prybar to remove the rotating assembly (16) from
the housing.
13. Remove Tooling (C) from shaft (15) .
Illustration 10 g00887424
14. Remove shaft (15) from rotating assembly (16) .
6/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 11 g00887426
15. Use Tooling (D) in order to remove retaining ring (17) from shaft (15) .
Illustration 12 g00887445
16. Install shaft (15) into a suitable press. Remove bearing race (18) from the shaft.
Illustration 13 g00887463
17. Rotate shaft (15) . Install shaft (15) into a suitable press. Install Tooling (E) . Remove
bearing race (19) from shaft (15) .
7/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 14 g00887501
18. Remove cam plate (20) from barrel assembly (21) .
Illustration 15 g00887520
19. Remove piston assemblies and retainer plate (22) from barrel assembly (21) .
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
8/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 16 g00887558
20. Remove ball (23) and springs (24) .
Illustration 17 g00887578
21. Remove bearing (25) .
22. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
23. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27) .
24. Remove seal (28) .
9/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g00887619
25. Remove bolts (29) and cover (30) .
Illustration 20 g00887729
26. Remove seal (31) and backup ring (32) .
Illustration 21 g00887754
27. Remove piston actuator (33) and seal (34) .
10/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 ...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 22 g00887762
28. Remove O-ring seal (35) from the housing of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 18:55:52 UTC+0800 2020
11/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 ...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326D2 EXCAVATOR KGY
Configuration: 326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03124523
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- Threaded Rod M12 x 1.75 X 250 mm (10 in) long 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G 9S-3263 Thread Lock Compound -
Note: Replace all O-ring seals and gaskets. Apply a light film of"10W" oil to all components
before assembly.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause trouble later. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
1/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33) .
2/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00887729
3. Install backup ring (32) and seal (31) .
Illustration 4 g00887619
4. Install cover (30) and bolts (29) . Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
3/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 5. Apply Tooling (G) to the mating surface of seal (28) . Use Tooling (E) in order to install
seal (28) .
6. Use Tooling (F) in order to install retaining ring (27) .
Illustration 6 g00887578
7. Rotate the housing.
8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25) .
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
4/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 10. Install springs (24) into the barrel. Install ball (23) onto springs (24) .
Illustration 8 g00887520
11. Install piston assemblies and retainer plate (22) into barrel assembly (21) .
Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Install cam plate (20) onto barrel assembly (21) .
5/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15) .
Illustration 11 g00887426
14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15) .
Illustration 12 g00888710
6/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 15. Install bearing race (18) onto shaft (15) .
Note: Bearing race (18) must contact retaining ring (17) .
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15) . Install shaft (15) into rotating assembly (16) .
17. Place the pump housing into Tooling (A) .
Illustration 14 g00887401
18. Use Tooling (C) in order to install rotating assembly (16) into the housing.
7/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 15 g00887501
Illustration 16 g00887578
19. The notches in cam plate (20) must align with keys (26) . The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
20. Install plates (13) and friction discs (14) into the housing.
8/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8) .
24. Install brake piston (8) into the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level in
order to prevent damage to the O-ring seals.
9/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6) .
Illustration 21 g00887302
26. Install O-ring seal (3) , port plate (4) , and bearing (5) .
Illustration 22 g00887295
27. Install head (2) onto the body of the travel motor.
10/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 ...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1) . Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By: Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 18:56:48 UTC+0800 2020
11/11
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 ...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326D2 EXCAVATOR KGY
Configuration: 326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i03808350
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded Rod 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/4
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g00878123
2. Install new O-ring seal (6) . Apply clean hydraulic oil on the O-ring seal.
Illustration 2 g00707267
3. Attach a suitable lifting device to travel motor (4) , as shown.
4. The weight of the travel motor is approximately 57 kg (125 lb).
Illustration 3 g00878121
2/4
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. 5. Carefully install travel motor (4) onto Tooling (A) . Slide the travel motor into the final
drive.
6. Install one of three bolts (5) that secures the travel motor to the final drive.
7. Remove Tooling (A) .
Illustration 4 g00707275
Typical example
8. Install remaining bolts (2) .
9. Connect hose assembly (3) . Connect hose assembly (1) .
10. Fill the final drive with oil.
ReferenceRefer to Operation and Maintenance Manual, "Lubricant Viscosities" for the
proper oil viscosity.
ReferenceRefer to Operation and Maintenance Manual, "Final Drive Oil Level - Check" for
the correct filling procedure.
11. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
12. Obtain a hydraulic oil sample from the main S·O·S port.
ReferenceRefer to Operation and Maintenance Manual, "Sampling Interval and Location of
Sampling Valve" for the correct location.
13. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system.
ReferenceRefer to Contamination Control Guidelines, SEBF8436, "Hydraulic System
Flushing Procedure for 322C Hydraulic Excavators" for further information.
3/4
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. End By: Install the travel brake valve. Refer to Disassembly and Assembly, "Travel Brake Valve
- Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 18:57:43 UTC+0800 2020
4/4
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326D2 EXCAVATOR KGY
Configuration: 326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326D2, 329D2 and 330D2 Excavators Machine Systems
Media Number -UENR6134-08 Publication Date -01/09/2018 Date Updated -12/09/2018
i05453056
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C
154-6184 Forcing Bolt (M 20) 2
154-6185(1)
Forcing Bolt (M 24) 2
(1)
For Use on 329 and 330 sales models
Start By:
a. Separate the track assembly.
b. Remove the travel motor.
1/3
326D2 & 326D2 L Excavators KGY00001-UP (MACHINE) POWERED BY C7.1 En...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...