The document provides instructions to disassemble a final drive for a 325D L excavator. Key steps include:
1. Marking the final drive for alignment and securing it in a repair stand.
2. Removing bolts and lifting devices to extract the cover and internal gears and shafts.
3. Using tools like retaining ring pliers to detach components like carrier assemblies.
4. Pressing shafts from carriers and disassembling carriers by removing pins, washers and gears.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...prmy389342
The document provides instructions to disassemble a final drive for a 324D L excavator. It involves removing over 30 individual parts in a specific sequence, including covers, gears, carriers, shafts, seals, and housings. Cleanliness is important to prevent dirt from entering during disassembly. Many parts need to be removed using specialized tools like retaining ring pliers, press machines, and lifting devices due to the weights of components ranging from 30 to 312 kg. Detailed illustrations are provided to identify each part.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...f7fujksekmdm8u
The document provides instructions for disassembling the final drive of a 324D L excavator. Key steps include:
1. Marking the final drive sections and fastening it to a repair stand.
2. Removing the cover bolts and setscrews, then lifting the cover off using tooling.
3. Removing bolts from the gear, checking the plate, and removing plugs from the cover.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...ufjksemd8ujd
The document provides instructions for disassembling a final drive on an excavator. It lists required tools and a multi-step process involving removing bolts, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be marked for proper reinstallation. Weights of removed parts are provided.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...8ufjsekddm8u
The document provides instructions for disassembling the final drive of a 324D L excavator. It lists required tools and a 33 step procedure that includes removing the final drive, cover, carrier assembly components, ring gears, and other internal parts. Disassembly requires the use of various tools, lifting devices, and forcing screws to separate components by driving out pins, removing bolts, and prying parts away from housings. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual Instant D...shanruliu7360
The document provides instructions for disassembling a final drive on an excavator. It lists required tools and a multi-step process involving removing bolts, gears, washers, seals, and other components. Key parts that are disassembled include the cover, carrier assemblies, planetary gears, and housings. Cleanliness is emphasized throughout the procedure.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual Instant D...kubei069369925
The document provides instructions for disassembling a final drive on an excavator. It lists required tools and a multi-step process involving removing bolts, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be marked for proper reinstallation. Weights of removed parts are provided.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...f8uesjdkdmdm
The document provides instructions for disassembling the final drive of a 324D L excavator. It lists required tools and a 33 step procedure involving removing bolts, gears, plates, seals, and housing components using various tools. Key components dismantled include the cover, carrier assembly, ring gears, sun gears, and housings. Cleanliness is emphasized and alignment marks should be made for reassembly.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...jdkskmdmdm
The document provides instructions for disassembling a final drive on an excavator. It lists required tools and a multi-step process involving removing bolts, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be marked for proper reinstallation. Weights of removed parts are provided.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...prmy389342
The document provides instructions to disassemble a final drive for a 324D L excavator. It involves removing over 30 individual parts in a specific sequence, including covers, gears, carriers, shafts, seals, and housings. Cleanliness is important to prevent dirt from entering during disassembly. Many parts need to be removed using specialized tools like retaining ring pliers, press machines, and lifting devices due to the weights of components ranging from 30 to 312 kg. Detailed illustrations are provided to identify each part.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...f7fujksekmdm8u
The document provides instructions for disassembling the final drive of a 324D L excavator. Key steps include:
1. Marking the final drive sections and fastening it to a repair stand.
2. Removing the cover bolts and setscrews, then lifting the cover off using tooling.
3. Removing bolts from the gear, checking the plate, and removing plugs from the cover.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...ufjksemd8ujd
The document provides instructions for disassembling a final drive on an excavator. It lists required tools and a multi-step process involving removing bolts, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be marked for proper reinstallation. Weights of removed parts are provided.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...8ufjsekddm8u
The document provides instructions for disassembling the final drive of a 324D L excavator. It lists required tools and a 33 step procedure that includes removing the final drive, cover, carrier assembly components, ring gears, and other internal parts. Disassembly requires the use of various tools, lifting devices, and forcing screws to separate components by driving out pins, removing bolts, and prying parts away from housings. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual Instant D...shanruliu7360
The document provides instructions for disassembling a final drive on an excavator. It lists required tools and a multi-step process involving removing bolts, gears, washers, seals, and other components. Key parts that are disassembled include the cover, carrier assemblies, planetary gears, and housings. Cleanliness is emphasized throughout the procedure.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual Instant D...kubei069369925
The document provides instructions for disassembling a final drive on an excavator. It lists required tools and a multi-step process involving removing bolts, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be marked for proper reinstallation. Weights of removed parts are provided.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...f8uesjdkdmdm
The document provides instructions for disassembling the final drive of a 324D L excavator. It lists required tools and a 33 step procedure involving removing bolts, gears, plates, seals, and housing components using various tools. Key components dismantled include the cover, carrier assembly, ring gears, sun gears, and housings. Cleanliness is emphasized and alignment marks should be made for reassembly.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...jdkskmdmdm
The document provides instructions for disassembling a final drive on an excavator. It lists required tools and a multi-step process involving removing bolts, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be marked for proper reinstallation. Weights of removed parts are provided.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual Instant D...rishang96299
The document provides instructions for disassembling a final drive on an excavator. It lists required tools and a multi-step process involving removing bolts, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be reinstalled in their original locations later. Various components like covers, gears and carriers are removed using lifting devices due to their significant weights ranging from 30-312 kg.
Caterpillar cat 324 d l excavator (prefix jjg) service repair manual (jjg0000...ujdkdkdmdm
The document provides instructions for disassembling the final drive of a 324D L excavator. It lists required tools and a 33 step procedure involving removing bolts, gears, plates, seals, and housing components using various tools. Key components dismantled include the cover, carrier assembly, ring gears, sun gears, and housings. Cleanliness is emphasized and weights of parts are provided.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...km7seydwuhdw
The document provides instructions for disassembling the final drive of a 324D L excavator. Key steps include:
1. Marking the final drive sections and fastening the drive to a repair stand.
2. Removing the cover bolts and setscrews, then lifting the cover off using tooling.
3. Removing bolts from the gear, checking the plate, and removing plugs from the cover.
Caterpillar cat 324 d l excavator (prefix jjg) service repair manual (jjg0000...fjskekazswdmme
The document provides instructions to disassemble a final drive for a 324D L excavator. Key steps include:
1. Marking the final drive for alignment and securing it in a repair stand.
2. Removing bolts, seals, gears, washers, and bearings from the final drive cover and carrier assemblies.
3. Using tools like retaining ring pliers and a press to remove additional components from within the assemblies.
4. Disassembling the carrier assemblies by driving out spring pins, removing thrust washers and planetary gears.
Caterpillar cat 324 d l excavator (prefix jjg) service repair manual (jjg0000...fjskekdmmem
The document provides instructions to disassemble a final drive for an excavator in 31 steps. It begins by removing the final drive assembly and cover, then disassembles the internal gears and carrier assemblies. Planetary gears, shafts, bearings and other small parts are removed from the carrier assemblies using punches and presses. Cleanliness is important to prevent dirt from entering during reassembly.
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...zan2736ban
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...fujkskemdmdm4r
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...f8uesjdkdmdm
The document provides instructions for disassembling a final drive component. It lists required tools and outlines 33 steps to remove parts like the cover, carrier assembly, ring gears, and seals. Cleanliness is important to prevent dirt from entering during reassembly. Weights of removed parts are provided to assist with lifting.
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...km7seydwuhdw
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...ufjksemd8ujd
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
The document provides instructions to disassemble a final drive assembly in 3 steps:
1. Remove the cover from the final drive assembly by lifting it with tooling.
2. Remove bolts and internal gear components from the cover.
3. Inspect and replace the check plate if wear is shown, and remove plugs from the cover.
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...8ufjsekddm8u
The document provides instructions to disassemble a final drive assembly in 3 steps:
1. Remove the cover from the final drive assembly by lifting it with tooling.
2. Remove bolts and internal gear components from the cover.
3. Inspect and replace the check plate if wear is shown. Remove plugs from the cover.
The document provides instructions to disassemble a final drive for an excavator. Key steps include:
1. Removing the final drive cover and gears.
2. Removing the carrier assembly and planetary gears.
3. Using presses and tools to remove shafts, gears, and bearings from the housing and carrier assembly.
Cleanliness is important to prevent dirt from entering during disassembly. Parts must be reinstalled in their original locations.
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for disassembling and assembling axle shaft assemblies and brake groups for a 938F wheel loader. It describes removing and installing the front and rear axle housing groups. The procedures are the same for both groups. Key steps include removing retaining rings, planetary carrier assemblies, seals, and applying shop air to remove brake pistons. New seals and lubrication with SAE 30 oil are required for reassembly.
This document provides instructions for removing and installing various components of a C27 Industrial Engine, including:
1. Removing the front gear group by removing bolts and gear assemblies.
2. Removing the front housing by removing covers, dampers, brackets, and bolts to detach the housing.
3. Removing the rear housing by removing elbow assemblies, bolts connecting the oil pan, and disconnecting hose assemblies.
More Related Content
Similar to Caterpillar Cat 325D L EXCAVATOR (Prefix T2S) Service Repair Manual (T2S00001 and up).pdf
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual Instant D...rishang96299
The document provides instructions for disassembling a final drive on an excavator. It lists required tools and a multi-step process involving removing bolts, gears, carriers, shafts, seals, and other components. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be reinstalled in their original locations later. Various components like covers, gears and carriers are removed using lifting devices due to their significant weights ranging from 30-312 kg.
Caterpillar cat 324 d l excavator (prefix jjg) service repair manual (jjg0000...ujdkdkdmdm
The document provides instructions for disassembling the final drive of a 324D L excavator. It lists required tools and a 33 step procedure involving removing bolts, gears, plates, seals, and housing components using various tools. Key components dismantled include the cover, carrier assembly, ring gears, sun gears, and housings. Cleanliness is emphasized and weights of parts are provided.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...km7seydwuhdw
The document provides instructions for disassembling the final drive of a 324D L excavator. Key steps include:
1. Marking the final drive sections and fastening the drive to a repair stand.
2. Removing the cover bolts and setscrews, then lifting the cover off using tooling.
3. Removing bolts from the gear, checking the plate, and removing plugs from the cover.
Caterpillar cat 324 d l excavator (prefix jjg) service repair manual (jjg0000...fjskekazswdmme
The document provides instructions to disassemble a final drive for a 324D L excavator. Key steps include:
1. Marking the final drive for alignment and securing it in a repair stand.
2. Removing bolts, seals, gears, washers, and bearings from the final drive cover and carrier assemblies.
3. Using tools like retaining ring pliers and a press to remove additional components from within the assemblies.
4. Disassembling the carrier assemblies by driving out spring pins, removing thrust washers and planetary gears.
Caterpillar cat 324 d l excavator (prefix jjg) service repair manual (jjg0000...fjskekdmmem
The document provides instructions to disassemble a final drive for an excavator in 31 steps. It begins by removing the final drive assembly and cover, then disassembles the internal gears and carrier assemblies. Planetary gears, shafts, bearings and other small parts are removed from the carrier assemblies using punches and presses. Cleanliness is important to prevent dirt from entering during reassembly.
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...zan2736ban
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...fujkskemdmdm4r
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...f8uesjdkdmdm
The document provides instructions for disassembling a final drive component. It lists required tools and outlines 33 steps to remove parts like the cover, carrier assembly, ring gears, and seals. Cleanliness is important to prevent dirt from entering during reassembly. Weights of removed parts are provided to assist with lifting.
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...km7seydwuhdw
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...ufjksemd8ujd
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
The document provides instructions to disassemble a final drive assembly in 3 steps:
1. Remove the cover from the final drive assembly by lifting it with tooling.
2. Remove bolts and internal gear components from the cover.
3. Inspect and replace the check plate if wear is shown, and remove plugs from the cover.
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...8ufjsekddm8u
The document provides instructions to disassemble a final drive assembly in 3 steps:
1. Remove the cover from the final drive assembly by lifting it with tooling.
2. Remove bolts and internal gear components from the cover.
3. Inspect and replace the check plate if wear is shown. Remove plugs from the cover.
The document provides instructions to disassemble a final drive for an excavator. Key steps include:
1. Removing the final drive cover and gears.
2. Removing the carrier assembly and planetary gears.
3. Using presses and tools to remove shafts, gears, and bearings from the housing and carrier assembly.
Cleanliness is important to prevent dirt from entering during disassembly. Parts must be reinstalled in their original locations.
Similar to Caterpillar Cat 325D L EXCAVATOR (Prefix T2S) Service Repair Manual (T2S00001 and up).pdf (19)
This document provides instructions for disassembling and assembling components of a C27 Industrial Engine, including:
1. Removing and installing the auxiliary drive by removing nuts, studs, pulley, gear, bearings, seals, and shaft.
2. Removing and installing the valve mechanism cover by removing and installing bolts and covers.
3. Removing and installing the valve mechanism cover base by removing tubes, harnesses, bolts, and installing seals and components.
This document provides instructions for disassembling and assembling axle shaft assemblies and brake groups for a 938F wheel loader. It describes removing and installing the front and rear axle housing groups. The procedures are the same for both groups. Key steps include removing retaining rings, planetary carrier assemblies, seals, and applying shop air to remove brake pistons. New seals and lubrication with SAE 30 oil are required for reassembly.
This document provides instructions for removing and installing various components of a C27 Industrial Engine, including:
1. Removing the front gear group by removing bolts and gear assemblies.
2. Removing the front housing by removing covers, dampers, brackets, and bolts to detach the housing.
3. Removing the rear housing by removing elbow assemblies, bolts connecting the oil pan, and disconnecting hose assemblies.
1) The document provides instructions for removing and installing various components of a Caterpillar C9.3 industrial engine, including disconnecting snap-to-connect fittings, removing and installing a muffler, and removing and installing a fuel priming pump and fuel filter base.
2) The procedures include illustrations showing the components and numbered steps for disassembly and reassembly. Safety warnings are provided at the beginning regarding relieving pressures before disconnection.
3) Torque specifications and required tools are listed for relevant installation steps.
This document provides instructions for removing and installing various fuel system components on a Caterpillar C9 Industrial Engine, including:
- Removing and installing the fuel priming pump
- Removing and installing the fuel filter base
- Removing a unit injector from the engine cylinder head
The procedures describe draining fluids, using specialty tools to remove and install parts, cleaning components, lubricating seals, and torquing bolts to the specified values. Technicians are advised to take precautions to prevent spills and contamination when working on the fuel system.
This document provides instructions for disassembling and assembling components of a 938F wheel loader transmission. It describes removing the transmission from the vehicle and then disassembling it into individual parts like shafts, gears, seals, and clutches. The multi-step process includes using various tools to compress springs, remove snap rings, and disassemble interconnected sub-assemblies. Reassembly follows the reverse order and includes inspecting parts for wear and replacing as needed.
This document provides instructions for removing and installing an engine oil filter base and oil cooler from a Caterpillar C9 Industrial Engine. It describes:
- Draining the coolant from the cooling system before removal
- Using a strap wrench to remove the oil filter
- Disconnecting hoses and removing bolts to take off the oil filter base and oil cooler
- Cleaning and installing replacement parts in the reverse order
This document provides instructions for removing and installing various engine components on a Caterpillar C27 Industrial Engine, including:
1) Valves, springs, and related parts using specialized tools to compress springs.
2) Valve guides using a driver tool and ensuring proper height.
3) Valve seat inserts using an extractor tool and driver to install new inserts.
4) The engine oil filter base and related internal parts, noting any spring pressure hazards.
Caterpillar Cat 345D L Excavator (Prefix EEH) Service Repair Manual (EEH00001...jdkskmmdmd1
This document provides instructions for disassembling and assembling the final drive components of a 345D L Excavator. It describes removing 28 components in 28 steps, including the final drive cover, carrier assemblies, ring gear, and sprocket housing. Reassembly is described in 21 steps, beginning with installing bearing cups into the sprocket housing and ending by attaching the coupling to the motor housing. Tools required are listed.
This document provides instructions for removing and installing various engine components on a C27 Industrial Engine, including:
1) Inlet and exhaust valves, springs, and related parts.
2) Inlet and exhaust valve guides.
3) Inlet and exhaust valve seat inserts.
4) The engine oil filter base.
The procedures describe the required tools and provide illustrations showing the parts. Safety notices are included regarding spring-loaded components.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...jdkskmmdmd1
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps to disassemble the motor by removing components like the head, plates, seals, pins, and brake piston. Identification marks should be made on parts for reassembly. To assemble, the document instructs reversing the 31 disassembly steps and notes that parts must be cleaned and reinstalled in their original locations and orientations.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...jdkskmmdmd1
1. The document provides instructions for removing and installing the rear gear group and flywheel on a C13 engine.
2. It details the required tools and presents a step-by-step process with illustrations for disassembling, inspecting, and reassembling each component.
3. Special attention is given to bearing installation and torque specifications for fasteners.
This document provides instructions for removing and installing various engine components on a Caterpillar C9 Industrial Engine, including:
1. Valves, valve guides, and valve seat inserts. It describes using specialized tools to compress springs and extract/install parts.
2. The engine oil filter base, oil cooler, and oil pump. It emphasizes cleaning parts and contains fluids properly during removal and installation.
3. Safety precautions are provided, such as wearing protective equipment when working with spring-loaded parts and ensuring contaminants are avoided. Numerical sequences and specifications are given for installing certain parts correctly.
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic systems. Used parts should be replaced with new ones and marks made to ensure correct reinstallation of parts.
Massey Ferguson 1652 COMPACT TRACTORS Parts Catalogue Manual.pdfjdkskmmdmd1
This document is a table of contents for the engine, fuel, and exhaust systems of Massey Ferguson 1648, 1652, and 1655 compact tractors. It contains 91 pages listing component part numbers and references for the engine, fuel injection, cooling, exhaust, and related systems. The pages are organized by component and sub-components.
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, pins, plates, seals, pistons, disks, and bearings. The assembly procedure reverses the disassembly process in 30 steps and provides notes about cleaning parts, applying lubricant, and ensuring proper orientation of components like washers. Tools required are listed for both procedures.
Caterpillar Cat 345D L Excavator (Prefix BYC) Service Repair Manual (BYC00001...jdkskmmdmd1
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a C13 engine, including:
- Removing the rear gear group which involves taking out multiple gears, covers, seals, and bearings.
- Removing the flywheel which requires lifting equipment due to its weight and removing the ring gear.
- Installing the rear gear group and flywheel components in reverse order, noting specific requirements like matching dimensions and applying threadlocker to bolts.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...jdkskmmdmd1
The document provides instructions for disassembling a travel motor. It lists 31 steps to remove parts like the head, plates, seals, pins, and piston assemblies. Proper cleaning and identification of parts is emphasized to ensure correct reassembly. Tools required are listed in a table.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...jdkskmmdmd1
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, port plate, brake piston, disks, and rotating group. The assembly procedure reverses the disassembly with 13 steps like installing seals, spacers, washers, and plugs. Proper cleaning, identification of parts, and use of recommended tools are emphasized to avoid contamination and ensure correct assembly.
Massey Ferguson MF 840 COMBINES Parts Catalogue Manual.pdfjdkskmmdmd1
The document contains parts lists and diagrams for Massey Ferguson MF 840/845 combines. It lists over 50 individual parts for the engine and accessories, including the cylinder block, crankshaft, cylinder head, rocker arm assembly and other components. Each part is given an item number, part number, quantity, description and any relevant comments. Diagrams illustrate the layout and components of the engine systems.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 154-6181 Forcing Screw 1
D 138-7574 Link Bracket 2
E
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F 1U-8846 Gasket Sealant 1
Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3/12
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. 3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
Illustration 3 g00708091
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
4/12
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 4 g00708235
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
Illustration 5 g00708092
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
Illustration 6 g01304883
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
5/12
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 7 g00708144
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
Illustration 8 g00708218
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
6/12
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 9 g00708162
13. Remove sun gear (14) from carrier assembly (15).
Illustration 10 g00708325
14. Remove spacer (16).
Illustration 11 g00708184
Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
7/12
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 12 g00708360
16. Use a screwdriver or a chisel in order to separate the two ring gears (17).
Note: The two ring gears are held together with Tooling (F). It may be necessary to heat the
ring gears in order to soften the sealant. Do not heat over 135 °C (275 °F) for more than
thirty minutes.
Illustration 13 g00708172
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
Illustration 14 g00708175
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
8/12
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 15 g00708370
Illustration 16 g00708220
b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
9/12
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 17 g00708186
22. Remove O-ring seal (24) from main housing (18).
Illustration 18 g00708187
23. Remove bolts (25) from gear (26).
Illustration 19 g00708202
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from the main housing (18) once gear (26) is
removed. Make sure that the motor housing is supported.
10/12
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 20 g00708211
25. Remove shims (27) from the main housing.
Illustration 21 g00708212
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from the motor housing (28). The combined weight of main housing (18) and the
final drive sprocket is approximately 82 kg (180 lb).
Illustration 22 g00708214
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
11/12
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Illustration 23 g00708215
Illustration 24 g00708216
30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Jun 5 12:08:25 UTC+0800 2020
12/12
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D L EXCAVATOR T2S
Configuration: 325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine
Disassembly and Assembly
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8646-22 Publication Date -01/02/2015 Date Updated -12/09/2018
i02783051
Final Drive - Disassemble
SMCS - 4050-015
S/N - A3R1-1021
S/N - AZP1-UP
S/N - DBH1-UP
S/N - EJC1-643
S/N - GBR1-UP
S/N - GPB1-801
S/N - JJG1-813
S/N - KBE1-UP
S/N - LAB1-415
S/N - LAL1-250
S/N - MCL1-201
S/N - NAC1-250
S/N - PAL1-UP
S/N - PKE1-814
S/N - SCR1-774
S/N - SYM1-617
1/13
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. S/N - T2D1-322
S/N - T2S1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 194-3878 Spanner Socket 1
E 138-7574 Link Bracket 2
F
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
G
1U-7600 Slide Hammer Puller Gp 1
8T-0266 Bolt 1
Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
Note: Some of the images that are in this procedure do not show the sprocket assembly that
is attached to the final drive housing. If necessary, the weights that are given include the
weight of the sprocket assembly.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
2/13
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The weight of the final drive assembly is
approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. Remove the cover. The weight of the cover is approximately 32 kg
(70 lb).
Illustration 3 g00879362
3/13
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. 5. Remove bolts (3). Remove gear (5). Check plate (6). Replace plate (6) if wear is shown.
Remove plugs (4) from cover (2).
Illustration 4 g00879365
6. Remove O-ring seal (7) from plugs (4).
Illustration 5 g00780428
7. Remove gear (8). Remove spacer (9).
Illustration 6 g00780432
4/13
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. 8. Remove retaining ring (10) with Tooling (C). Remove washer (11). Remove gear (12).
Remove bearing assembly (13). Remove second washer (11).
9. Repeat Step 8 for the remaining two gear assemblies.
Illustration 7 g00781401
10. Remove retaining ring (14).
Illustration 8 g00781407
11. Remove carrier assembly (15).
5/13
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 9 g01389593
12. Use a suitable press in order to remove the shafts from carrier assembly (15).
Illustration 10 g00781412
13. Remove gear (16). Remove spacer (17).
Illustration 11 g00781466
6/13
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 14. Remove retaining ring (18).
15. Remove carrier assembly (19).
Illustration 12 g00879368
16. Disassemble carrier assembly (19), as follows.
a. Drive spring pin (20) into planetary shaft (21) with a hammer and a punch.
Illustration 13 g00781476
b. Remove planetary shaft (21).
c. Remove spring pin (20) from planetary shaft (21) with a hammer and a punch.
7/13
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 14 g00781516
d. Remove thrust washers (22) and planetary gear (24) from the carrier assembly.
e. Remove bearing (23) from planetary gear (24).
17. Repeat Steps 16.a through 16.e for the other two planetary.
Illustration 15 g00781529
18. Remove gear (25). Remove spacer (26).
Illustration 16 g00781559
19. Remove carrier assembly (27).
20. Use two people to remove carrier assembly (27). The weight of the carrier assembly is
approximately 38 kg (85 lb).
21. Disassemble carrier assembly (27), as follows.
8/13
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 17 g00781719
a. Drive spring pin (29) into planetary shaft (28) with a hammer and a punch.
Illustration 18 g00781601
b. Remove planetary shaft (28).
c. Remove spring pin (29) from planetary shaft (28) with a hammer and a punch.
Illustration 19 g00781607
d. Remove thrust washers (30) and planetary gear (32) from the carrier assembly.
e. Remove two bearings (31) from the planetary gear.
9/13
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. 22. Repeat Steps 21.a through 21.e for the other two planetary gears.
Illustration 20 g00781730
23. Use two people to remove gear (33). The weight of gear is approximately 41 kg (90 lb).
Illustration 21 g00781807
24. Remove O-ring seal (34).
Illustration 22 g01147650
25. Remove bolts (35A) and plates (35B).
10/13
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 23 g01147651
26. Use Tooling (G) to remove dowel (37) from stopper plate (35).
Illustration 24 g01147759
27. Secure Tooling (D) to stopper plate (35). Use Tooling (D) to remove stopper plate (35).
Illustration 25 g01147930
28. Use Tooling (E) and a suitable lifting device to remove housing (36). The weight of housing
(36) is approximately 100 kg (220 lb).
11/13
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 26 g01147951
29. Remove Duo-Cone seal (39A) from housing (38).
Illustration 27 g01147975
Illustration 28 g01147934
30. Remove Duo-Cone seal (39B) from housing (36).
31. Use Tooling (F) in order to remove bearings (40) and (41) from housing (36).
32. If necessary, remove the final drive sprocket from the sprocket housing. Refer to
Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
12/13
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engi...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325D L EXCAVATOR T2S
Configuration: 325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine
Disassembly and Assembly
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8646-22 Publication Date -01/02/2015 Date Updated -12/09/2018
i03949150
Final Drive - Assemble
SMCS - 4050-016
S/N - A3R1-UP
S/N - AZP1-UP
S/N - BFC1-UP
S/N - BYS1-UP
S/N - CZF1-UP
S/N - DBH1-UP
S/N - DJF1-UP
S/N - DTZ1-UP
S/N - EBM1-UP
S/N - EJC1-UP
S/N - GBR1-UP
S/N - GPB1-UP
S/N - GPK1-UP
S/N - JAT1-UP
S/N - JHJ1-UP
S/N - JJG1-UP
1/15
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
D 138-7574 Link Bracket 2
G 126-3994 Duo-Cone Seal Installer 1
H 5P-3931 Anti-Seize Compound
F 1U-8846 Gasket Sealant
Note: Cleanliness is an important factor. Before assembly, all parts should be cleaned in
cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry
parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If
any parts are worn or damaged, use new parts for replacement. All disassembly and all
assembly procedures must be performed on a clean work surface and in a clean hydraulic
area. Keep cleaned parts covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have
the same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound
during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
1. Install the final drive sprocket if the sprocket was removed from the main housing.
2. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Illustration 1 g00708215
3. Apply Tooling (H) to the outer diameter of the bearings.
4. Install bearings (32) and (33) in main housing (18) with a suitable press.
5. Make sure that bearing (32) and bearing (33) contact the counterbore in the main housing.
6. Use the following procedure to preload the bearings and determine the correct thickness of
shims.
3/15
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. Illustration 2 g00713058
a. Fasten Tooling (D) and a suitable lifting device to main housing (18) . Install the main
housing on the motor housing.
b. Put the main housing and the motor housing in a suitable press.
Illustration 3 g00709278
(a) Bearing surface
(b) Housing surface
c. Use a suitable press and a spacer in order to apply a load of 4000 kg (8818.5 lb) on
the bearings. Rotate the housing in order to seat the bearings.
d. Reduce the load on the bearings to 1000 ± 100 kg (2204.6 ± 220.5 lb).
e. Use a depth micrometer in order to measure the step length between the bearing
surface and the housing surface. Take measurements at several different locations
around the housing. Compute the average of the measured dimensions and record the
number. Call this Dimension (Y) .
4/15
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Illustration 4 g00709276
f. Use a depth micrometer in order to measure the step length of the coupling gear (26) .
Take measurements at several different locations around the gear. Compute the
average of the measured dimensions and record the number. Call this Dimension (X) .
g. The thickness of the shims is equal to (X - Y) ± 0.05 mm (0.002 inch).
Note: Use no more than two shims. If two shims are required, install the thinner shim
next to the gear.
h. Remove the main housing from the motor housing.
Illustration 5 g01021370
7. Use Tooling (G) in order to install Duo-Cone seal (31) in main housing (18) . Refer to
Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contact the seals must be clean and dry. After
installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal seals.
5/15
325D L Hydraulic Excavator T2S00001-UP (MACHINE) POWERED BY C-7 Engine...
2020/6/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...