The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and tapping guides into place. Safety notices warn of potential injury from parts propelled by springs and ensure clean parts to prevent premature wear.
Caterpillar cat 325 c excavator (prefix s2c) service repair manual (s2c00001 ...fjsekkdmme
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 325C excavator with a 3126 engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and ensuring parts are clean. Safety notices are included to warn of potential injury from parts propelled by springs.
The document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator including:
- Valves, valve guides, and valve seat inserts from the cylinder head. It describes the required tools and multi-step procedures.
- The engine oil filter base which connects the oil filter and oil cooler lines. Photos show its removal from the engine.
- Disassembling the engine oil filter base to access the oil cooler bypass valve and oil filter bypass valve.
- Assembly procedures for reinstalling components like the engine oil filter base after maintenance or repair. Precautions are given to prevent contamination of parts.
The document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator including:
- Valves, valve guides, and valve seat inserts from the cylinder head. It describes the required tools and multi-step procedures.
- The engine oil filter base which includes removing the oil filter assembly, disconnecting tubes, and removing the base.
- Disassembling the engine oil filter base by removing the oil cooler bypass valve and oil filter bypass valve.
- Reassembling the engine oil filter base, noting to keep all parts clean from contaminants.
The document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator including:
- Valves, valve guides, and valve seat inserts from the cylinder head. It describes the required tools and multi-step procedures.
- The engine oil filter base which connects the oil filter and oil cooler lines. Photos show its removal from the engine.
- Disassembling the engine oil filter base to access the oil cooler bypass valve and oil filter bypass valve.
- Reassembling the engine oil filter base before reinstalling it on the engine. Precautions are given to prevent contamination of parts.
Caterpillar cat 325 c excavator (prefix blx) service repair manual (blx00001 ...fjsekkdmme
This document provides instructions for removing and installing engine components on a 325C excavator, including:
- Inlet and exhaust valves, using valve spring compressors and other tools.
- Inlet and exhaust valve guides, using driver tools.
- Inlet and exhaust valve seat inserts, using extractor tools and an installer tool.
- The engine oil filter base, using a strap wrench.
Detailed steps are given for each procedure, including required tools and safety notices.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...yu5676962
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator. The instructions include:
1) Removing the idler gear from the front gear group using a puller tool and driver group.
2) Installing a new crankshaft rear seal using a installer tool, locator, bolts and washer. The seal is pressed onto the crankshaft using the tools.
3) Removing and installing the flywheel housing which requires lifting equipment and removal of bolts, washers and gaskets. The oil seal in the housing is also removed and installed using driver tools.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...ze6074xunong
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves cleaning the crankshaft, applying retaining compound, and pressing the new seal into place using a slide hammer puller. Care must be taken not to damage the crankshaft flange during installation.
Caterpillar cat 325 c excavator (prefix s2c) service repair manual (s2c00001 ...fjsekkdmme
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 325C excavator with a 3126 engine. It describes the required tools and multi-step procedures for each task, including compressing springs, removing retainers, and ensuring parts are clean. Safety notices are included to warn of potential injury from parts propelled by springs.
The document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator including:
- Valves, valve guides, and valve seat inserts from the cylinder head. It describes the required tools and multi-step procedures.
- The engine oil filter base which connects the oil filter and oil cooler lines. Photos show its removal from the engine.
- Disassembling the engine oil filter base to access the oil cooler bypass valve and oil filter bypass valve.
- Assembly procedures for reinstalling components like the engine oil filter base after maintenance or repair. Precautions are given to prevent contamination of parts.
The document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator including:
- Valves, valve guides, and valve seat inserts from the cylinder head. It describes the required tools and multi-step procedures.
- The engine oil filter base which includes removing the oil filter assembly, disconnecting tubes, and removing the base.
- Disassembling the engine oil filter base by removing the oil cooler bypass valve and oil filter bypass valve.
- Reassembling the engine oil filter base, noting to keep all parts clean from contaminants.
The document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator including:
- Valves, valve guides, and valve seat inserts from the cylinder head. It describes the required tools and multi-step procedures.
- The engine oil filter base which connects the oil filter and oil cooler lines. Photos show its removal from the engine.
- Disassembling the engine oil filter base to access the oil cooler bypass valve and oil filter bypass valve.
- Reassembling the engine oil filter base before reinstalling it on the engine. Precautions are given to prevent contamination of parts.
Caterpillar cat 325 c excavator (prefix blx) service repair manual (blx00001 ...fjsekkdmme
This document provides instructions for removing and installing engine components on a 325C excavator, including:
- Inlet and exhaust valves, using valve spring compressors and other tools.
- Inlet and exhaust valve guides, using driver tools.
- Inlet and exhaust valve seat inserts, using extractor tools and an installer tool.
- The engine oil filter base, using a strap wrench.
Detailed steps are given for each procedure, including required tools and safety notices.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...yu5676962
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator. The instructions include:
1) Removing the idler gear from the front gear group using a puller tool and driver group.
2) Installing a new crankshaft rear seal using a installer tool, locator, bolts and washer. The seal is pressed onto the crankshaft using the tools.
3) Removing and installing the flywheel housing which requires lifting equipment and removal of bolts, washers and gaskets. The oil seal in the housing is also removed and installed using driver tools.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...ze6074xunong
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves cleaning the crankshaft, applying retaining compound, and pressing the new seal into place using a slide hammer puller. Care must be taken not to damage the crankshaft flange during installation.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...yfjskemdmdm
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...f8usejdkdm3ed
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator. The instructions include:
1) Removing the idler gear from the front gear group using a puller tool and driver group.
2) Installing a new crankshaft rear seal using a installer tool, locator, bolts and washer. The seal is pressed onto the crankshaft using the tools.
3) Removing and installing the flywheel housing which requires lifting equipment and removal of bolts, washers and gaskets. The oil seal in the housing is also removed and installed using driver tools.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...gongfuao7509
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...mbk336997
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...fsejkddmmdmd
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...f8seodkdmdmed3
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...jdksmemd1
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator. The instructions include:
- Removing the idler gear from the front gear group using a puller tool and driver group.
- Installing a new crankshaft rear seal using a installer tool, locator, bolts and washer. The seal is pressed onto the crankshaft using the tools.
- Removing and installing the flywheel housing which requires lifting equipment and removal of bolts, washers and gaskets. The housing weighs approximately 29 kg.
- Procedures are provided in detail with illustrations and lists of required tools. Safety and contamination prevention notices are also
Caterpillar cat 325 c excavator (prefix jlc) service repair manual (jlc00001 ...fjjskejdmdn
The document provides instructions for checking and installing crankshaft components in a 3126B engine, including:
1. Removing the crankshaft rear seal and checking clearance of the crankshaft wear sleeve.
2. Installing the crankshaft rear seal and wear sleeve using various tools to set proper clearance.
3. Removing and installing the crankshaft gear from the crankshaft, ensuring the woodruff key is properly positioned.
4. Checking clearance of the installed crankshaft using a dial indicator.
The summary highlights the main components and steps discussed in the document - removing and installing the crankshaft rear seal, wear sleeve,
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fhsejkdkmen
The document provides instructions for checking and installing crankshaft components in a 3126B engine, including:
1. Removing the crankshaft rear seal and checking clearance of the crankshaft wear sleeve.
2. Installing the crankshaft rear seal and wear sleeve using various tools to set proper clearance.
3. Removing and installing the crankshaft gear from the crankshaft, ensuring the woodruff key is properly positioned.
4. Checking clearance of the installed crankshaft using a dial indicator.
The procedures describe cleaning parts, applying oil, using pullers and other tools to correctly position components while maintaining proper clearance and avoiding contamination.
This document provides instructions for removing and installing engine components on a 325C excavator, including:
- Removing and installing inlet and exhaust valves, using specialized tools to compress springs.
- Removing and installing valve guides with driver tools.
- Removing and installing valve seat inserts with an extractor tool.
- Removing the engine oil filter base using a strap wrench. Detailed steps and illustrations are provided for each procedure.
This document provides instructions for removing and installing engine components on a 325C excavator, including:
- Removing and installing inlet and exhaust valves, using specialized tools to compress springs.
- Removing and installing valve guides using driver tools to ensure proper height protrusion.
- Removing and installing valve seat inserts with an extractor tool and installer tool.
- Removing the engine oil filter base using a strap wrench to contain any fluids. Detailed illustrations and tables of required tools are provided for each procedure.
This document provides instructions for removing and installing engine components on a 325C excavator, including:
- Removing and installing inlet and exhaust valves, using specialized tools to compress springs.
- Removing and installing valve guides with driver tools.
- Removing and installing valve seat inserts with an extractor tool.
- Removing the engine oil filter base using a strap wrench. Detailed steps and illustrations are provided for each procedure.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures, highlighting important safety notices. Removal involves compressing springs with a tool and removing retaining components. Installation requires lubricating, inserting, and securing parts in the specified order and orientation.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual Instant D...fskekkdmdmdm3e
- The document provides instructions for removing and installing the idler gear of the front gear group on a C4.2 engine for Caterpillar built machines.
- To remove the idler gear, the front housing must first be removed. Then the idler gear bolt, thrust plate, and idler gear can be taken off the idler gear shaft. An idler shaft puller and driver group may be needed.
- To install the idler gear, first press in a new bushing if needed. Then install the idler shaft, idler gear, thrust plate, washer and idler gear bolt. Tighten the bolt to the specified torque.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly process removes components like housing, gears, seals and bearings. The 22 step assembly process reverses this to rebuild the final drive, applying loctite and torquing bolts to specification. Tools required include link brackets, crossblocks, drivers and torque wrenches. Safety precautions are noted for releasing spring forces.
More Related Content
Similar to Caterpillar Cat 325C EXCAVATOR (Prefix S2C) Service Repair Manual Instant Download.pdf
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...yfjskemdmdm
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...f8usejdkdm3ed
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator. The instructions include:
1) Removing the idler gear from the front gear group using a puller tool and driver group.
2) Installing a new crankshaft rear seal using a installer tool, locator, bolts and washer. The seal is pressed onto the crankshaft using the tools.
3) Removing and installing the flywheel housing which requires lifting equipment and removal of bolts, washers and gaskets. The oil seal in the housing is also removed and installed using driver tools.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...gongfuao7509
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...mbk336997
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...fsejkddmmdmd
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...f8seodkdmdmed3
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine:
1. Clean the crankshaft flange and inside of the new seal with a primer and retaining compound.
2. Install the new seal onto the crankshaft using a slide hammer puller, ensuring it is seated evenly without damaging the crankshaft flange.
3. Inspect the installed seal to ensure proper installation.
The document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. It lists the required tools which include an idler shaft puller and driver group. The procedure involves removing the front housing, then using the puller tool to remove the idler gear shaft from the front housing.
Caterpillar Cat 320D L Excavator (Prefix A8F) Service Repair Manual (A8F00001...jdksmemd1
The document provides instructions for removing and installing various engine components on a Caterpillar 320D L excavator. The instructions include:
- Removing the idler gear from the front gear group using a puller tool and driver group.
- Installing a new crankshaft rear seal using a installer tool, locator, bolts and washer. The seal is pressed onto the crankshaft using the tools.
- Removing and installing the flywheel housing which requires lifting equipment and removal of bolts, washers and gaskets. The housing weighs approximately 29 kg.
- Procedures are provided in detail with illustrations and lists of required tools. Safety and contamination prevention notices are also
Caterpillar cat 325 c excavator (prefix jlc) service repair manual (jlc00001 ...fjjskejdmdn
The document provides instructions for checking and installing crankshaft components in a 3126B engine, including:
1. Removing the crankshaft rear seal and checking clearance of the crankshaft wear sleeve.
2. Installing the crankshaft rear seal and wear sleeve using various tools to set proper clearance.
3. Removing and installing the crankshaft gear from the crankshaft, ensuring the woodruff key is properly positioned.
4. Checking clearance of the installed crankshaft using a dial indicator.
The summary highlights the main components and steps discussed in the document - removing and installing the crankshaft rear seal, wear sleeve,
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fhsejkdkmen
The document provides instructions for checking and installing crankshaft components in a 3126B engine, including:
1. Removing the crankshaft rear seal and checking clearance of the crankshaft wear sleeve.
2. Installing the crankshaft rear seal and wear sleeve using various tools to set proper clearance.
3. Removing and installing the crankshaft gear from the crankshaft, ensuring the woodruff key is properly positioned.
4. Checking clearance of the installed crankshaft using a dial indicator.
The procedures describe cleaning parts, applying oil, using pullers and other tools to correctly position components while maintaining proper clearance and avoiding contamination.
This document provides instructions for removing and installing engine components on a 325C excavator, including:
- Removing and installing inlet and exhaust valves, using specialized tools to compress springs.
- Removing and installing valve guides with driver tools.
- Removing and installing valve seat inserts with an extractor tool.
- Removing the engine oil filter base using a strap wrench. Detailed steps and illustrations are provided for each procedure.
This document provides instructions for removing and installing engine components on a 325C excavator, including:
- Removing and installing inlet and exhaust valves, using specialized tools to compress springs.
- Removing and installing valve guides using driver tools to ensure proper height protrusion.
- Removing and installing valve seat inserts with an extractor tool and installer tool.
- Removing the engine oil filter base using a strap wrench to contain any fluids. Detailed illustrations and tables of required tools are provided for each procedure.
This document provides instructions for removing and installing engine components on a 325C excavator, including:
- Removing and installing inlet and exhaust valves, using specialized tools to compress springs.
- Removing and installing valve guides with driver tools.
- Removing and installing valve seat inserts with an extractor tool.
- Removing the engine oil filter base using a strap wrench. Detailed steps and illustrations are provided for each procedure.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a 3126B engine. It describes the required tools and multi-step procedures, highlighting important safety notices. Removal involves compressing springs with a tool and removing retaining components. Installation requires lubricating, inserting, and securing parts in the specified order and orientation.
Similar to Caterpillar Cat 325C EXCAVATOR (Prefix S2C) Service Repair Manual Instant Download.pdf (18)
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual Instant D...fskekkdmdmdm3e
- The document provides instructions for removing and installing the idler gear of the front gear group on a C4.2 engine for Caterpillar built machines.
- To remove the idler gear, the front housing must first be removed. Then the idler gear bolt, thrust plate, and idler gear can be taken off the idler gear shaft. An idler shaft puller and driver group may be needed.
- To install the idler gear, first press in a new bushing if needed. Then install the idler shaft, idler gear, thrust plate, washer and idler gear bolt. Tighten the bolt to the specified torque.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly process removes components like housing, gears, seals and bearings. The 22 step assembly process reverses this to rebuild the final drive, applying loctite and torquing bolts to specification. Tools required include link brackets, crossblocks, drivers and torque wrenches. Safety precautions are noted for releasing spring forces.
Caterpillar Cat 336F and 336F L Excavator (Prefix DSW) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs and seals. Tools required include a transmission repair stand, lifting eye assembly, driver group and various bolts, pins and seals. Technicians are advised to mark components for reinstallation and take care when removing parts to avoid damage.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 345D L Excavator (Prefix JKN) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, bearings and other components into the travel motor housing and barrel. Measurements are taken throughout to ensure proper assembly. The travel motor is then installed on the excavator and filled with the correct oil type.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor. It details 27 steps for assembling the travel motor that include installing seals, springs, pistons, and other components in the proper order and orientation. Thirteen steps are listed for disassembling the final drive, which include removing the cover, gears, and planetary gear assembly. Personal injury warnings are provided and all components must be cleaned before assembly.
Caterpillar Cat 336E L Excavator (Prefix BZY) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor of a 336E L excavator. The disassembly procedure involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstalling parts. Special care must be taken when handling springs or parts under spring force to avoid injury.
Caterpillar Cat 330F and 330F L Excavator (Prefix LCG) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. It describes 37 steps to disassemble the final drive by removing gears, shafts, housings, seals and other components. It then describes 34 steps to reassemble the final drive, including pressing in new bearings, installing seals, adjusting bearing preload with shims, and applying threadlocker to bolts. Precise tools and lifting devices are required due to the heavy weights of up to 550 kg involved.
Caterpillar Cat 336E L Excavator (Prefix DPX) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor on a 336E L excavator. The disassembly process involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on lubricating parts and ensuring proper alignment of components.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fskekkdmdmdm3e
1) The document provides step-by-step instructions for disassembling the travel motor of a 336D2L excavator.
2) It describes removing over 30 components of the travel motor including the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates and more.
3) Detailed illustrations are provided to accompany each step showing how to remove each component using the recommended tools.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It describes 13 steps to remove the component, which include disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. 11 steps are listed to install the component, in reverse order, including attaching lifting devices, positioning the assembly, and reinstalling hoses and covers. Tools and torque specifications are provided.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLC) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for removing and installing a crankshaft wear sleeve and crankshaft gear on a 325C excavator. It describes using various tools to distort and remove the existing wear sleeve and instructions for installing a new sleeve using a multi-piece installer tool. It also outlines steps for removing the crankshaft gear using a bearing puller and installing the gear by heating it and pressing it onto the crankshaft. The document provides maintenance technicians with detailed parts and tool information as well as safety notices for completing these tasks.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for assembling and installing a travel motor. It outlines 34 steps for assembling components like pistons, seals, plates, and bearings. It also describes using tools to measure clearances and distances during assembly. Finally, it details installing the assembled travel motor using lifting devices and bolts, and connecting hydraulic hose assemblies.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for removing and installing the rear gear group and rear crankshaft seal of a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 12 steps including cleaning parts, installing bearings, seals, gears, and bolts while ensuring proper dimensions and torque specifications are followed. Tools required include drivers, link brackets, guide studs, and installation tools.
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306B engine. It describes:
1) Marking the gears to ensure proper timing during removal and installation.
2) Removing the camshaft bolts and carefully removing the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before installation.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
The document provides instructions for removing and installing various components of a Caterpillar 621E wheel scraper, including:
1) Removing and installing the push-pull plate that connects the push-pull spring to the support assembly.
2) Disassembling and assembling the push-pull spring itself by removing discs and plates.
3) A detailed process for removing and installing the ejector cylinder, which requires the use of lifting tools and wood blocks due to the cylinder's weight.
4) Brief instructions for removing and adjusting the position of the lower front and guide rollers on the ejector assembly.
This document provides assembly instructions for a final drive on an excavator. It involves assembling and installing several components in the following order: installing bearings and determining shim thickness; installing seals; installing dowel pins; installing the housing on the motor housing; installing coupling gear, bolts, and ring gear; assembling carrier assemblies; installing gears, shafts, and retaining rings; installing the cover and testing for leaks. The process requires precision measurements and uses several specialized tools to properly assemble the final drive.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR S2C
Configuration: 325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02374873
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. Illustration 1 g00991548
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Use Tooling (A) to compress valve spring (4). Remove retainer lock (6).
2. Remove Tooling (A). Remove spring retainer (5), valve spring (4), and washer (3).
3. Remove valve seal (1) and valve (2).
4. Repeat Steps 1 through 3 in order to remove the remaining inlet valves and exhaust valves.
Installation Procedure
2/4
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00991548
The valve spring keepers can be thrown from the valve when the valve
spring compressor is released. Ensure that the valve spring keepers are
3/4
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. properly installed on the valve stem. To help prevent personal injury,
keep away from the front of the valve spring keepers and valve springs
during the installation of the valves.
1. Lubricate valve (2) with clean engine oil. Install valve (2) in the cylinder head assembly.
Install new valve seal (1) onto the valve guide.
2. Place the following items on the valve stem: washer (3), valve spring (4) and spring retainer
(5).
Note: A small amount of grease can be used to hold the retainer locks in position during
installation.
3. Use Tooling (A) to compress valve spring (4). Install retainer lock (6).
4. Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves.
End By:
a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 7 07:31:25 UTC+0800 2020
4/4
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR S2C
Configuration: 325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01979506
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver 1
B 9U-6895 Valve Guide Driver 1
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 1 g01029395
1. Use Tooling (A) to remove inlet valve guides (2) from the cylinder head assembly. Use
Tooling (B) to remove exhaust valve guides (1) from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver 1
B 9U-6895 Valve Guide Driver 1
C 1U-7792 Guide Collar 1
D 149-4008 Guide Collar 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 2 g01029395
1. Position inlet valve guide (2) and tap on the top of inlet valve guide (2).
2. Use Tooling (A) and Tooling (C) to install inlet valve guide (2). Install inlet valve guides
(2) until the protrusion is 23.0 ± 0.5 mm (0.90 ± 0.02 inch) above the cylinder head
assembly.
3. Use Tooling (B) and Tooling (D) to install exhaust valve guide (1). Install exhaust valve
guide (1) until the protrusion is 17.8 ± 0.5 mm (0.70 ± 0.02 inch) above the cylinder head
assembly.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 7 07:32:20 UTC+0800 2020
3/3
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR S2C
Configuration: 325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02368759
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor 1
B(1)
165-5647 Valve Seat Extractor 1
C(1)
6V-4804 Handle 1
D(1)
6V-4192 Shaft 1
E(1)
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool Group
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 1 g00987231
Illustration 2 g00987198
Note: Replace Tooling (A) with Tooling (B) for the removal of the inlet valve seat insert.
1. Install Tooling (A) in the exhaust valve seat insert.
2/4
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. 2. Install Tooling (C) and Tooling (D) in Tooling (A). Hand tighten Tooling (D). Tooling (A)
will expand below the edge of valve seat insert (1).
Illustration 3 g00987225
3. Install Tooling (E) on the cylinder head under Tooling (C). Hold Tooling (D) while you turn
Tooling (C). Remove valve seat (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
F 149-6115 Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/4
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 4 g00987231
Note: Do not machine the prefinished valve seat inserts in order to correct the valve stem
projection. An excessive valve stem projection indicates that the valve seat insert is not
seated or material was not cleaned from the bottom of the counterbore.
1. Turn Tooling (F) upside-down and use Tooling (F) and a press to install valve seat inserts
(1) in the cylinder head assembly.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 7 07:33:16 UTC+0800 2020
4/4
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR S2C
Configuration: 325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02221389
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/2
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Dispose of all fluids according to local regulations and mandates.
Note: Remove the turbocharger, if necessary. Refer to Disassembly and Assembly,
"Turbocharger - Remove".
Illustration 1 g01026328
1. Remove oil filter assembly (1) with Tooling (A).
2. Disconnect tube assembly (2) from the elbow assembly.
3. Remove engine oil filter base (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 7 07:34:12 UTC+0800 2020
2/2
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR S2C
Configuration: 325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02229026
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base and the oil cooler. Refer to Disassembly and Assembly,
"Engine Oil Filter Base and Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. Illustration 1 g01124604
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
(1) Oil cooler bypass valve
(2) Oil filter bypass valve
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 7 07:35:07 UTC+0800 2020
2/2
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR S2C
Configuration: 325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02229174
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 1 g01124604
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
(1) Oil cooler bypass valve
(2) Oil filter bypass valve
End By:
a. Install the engine oil filter base and the oil cooler. Refer to Disassembly and Assembly,
"Engine Oil Filter Base and Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 7 07:36:03 UTC+0800 2020
2/2
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR S2C
Configuration: 325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02473092
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Illustration 1 g01026328
Illustration 2 g01185803
1. Position the gasket and engine oil filter base (3) over the engine oil cooler.
2/3
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. 2. Install the bolts that hold engine oil filter base (3) to the cylinder block. Tighten the bolts in
sequence according to the following procedure:
a. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 15 N·m (11
lb ft).
b. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 28 N·m (21
lb ft).
3. Connect tube assembly (2) to engine oil filter base (3) .
4. Install oil filter assembly (1) with Tooling (A) . Follow the instructions with the oil filter
assembly for the correct installation.
Note: Install the turbocharger, if necessary. Refer to Disassembly and Assembly,
"Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 7 07:36:59 UTC+0800 2020
3/3
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR S2C
Configuration: 325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02958037
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Personal injury can result from hot coolant, steam and alkali.
At operating temperature, engine coolant is hot and under pressure. The
radiator and all lines to heaters or the engine contain hot coolant or
steam. Any contact can cause severe burns.
Remove cooling system pressure cap slowly to relieve pressure only
when engine is stopped and cooling system pressure cap is cool enough
to touch with your bare hand.
Do not attempt to tighten hose connections when the coolant is hot, the
hose can come off causing burns.
Cooling System Coolant Additive contains alkali. Avoid contact with
skin and eyes.
NOTICE
1/3
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01026362
2/3
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. 1. Remove engine oil cooler (1) and the gasket from the cylinder block.
2. Remove O-ring seals (2) from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 7 07:37:55 UTC+0800 2020
3/3
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR S2C
Configuration: 325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01979965
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. Illustration 1 g01026362
1. Install O-ring seals (2) in the cylinder block.
2. Put the gasket and engine oil cooler (1) in the cylinder block.
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 7 07:38:50 UTC+0800 2020
2/2
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR S2C
Configuration: 325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01980628
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine(SE...
2020/7/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...