This document provides instructions for removing and installing inlet manifold components on a Caterpillar 325B excavator engine. The summary is:
1. Remove the valve mechanism cover and disconnect any attached lines and solenoids from the inlet manifold.
2. Remove bolts securing the inlet manifold and remove the manifold and gasket.
3. To install the inlet manifold, position a new gasket and manifold on the engine and secure it with bolts, reconnecting any lines or solenoids.
Caterpillar cat 325 l track type excavator (prefix 7cj) service repair manual...diskkdkdmdm
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...orrf0370383
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...orrf0370383
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...fuusejkddmmd3e
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...fuusejkddmmd3e
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...dujkdksmdmdm
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...dujkdksmdmdm
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...jdksmmdmdd
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar cat 325 l track type excavator (prefix 7cj) service repair manual...diskkdkdmdm
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...orrf0370383
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...orrf0370383
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...fuusejkddmmd3e
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...fuusejkddmmd3e
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...dujkdksmdmdm
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...dujkdksmdmdm
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...jdksmmdmdd
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...jdksmmdmdd
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...fujkse9didkke3
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar cat 325 track type excavator (prefix 7 cj) service repair manual ...diskkdkdmdm
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...fjkdksmmdm
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids. Referenced tools and their part numbers are listed.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...fjkdksmmdm
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fuusejkddmmd3e
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fuusejkddmmd3e
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...dujkdksmdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...jdksmmdmdd
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...dujkdksmdmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...jdksmmdmdd
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
DAEWOO DOOSAN MEGA 160TC TIER-II WHEEL LOADER Parts Catalogue Manual.pdfjfkskmmdmdm
The document provides a parts list and diagrams for components of a MEGA 160TC TIER-II engine. It includes lists of cylinder block, timing gear case, flywheel housing, crankshaft, and cylinder head parts with part numbers, descriptions, quantities, serial numbers and replacement part information. The parts are identified by key numbers on diagrams of each engine component.
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 325B L excavator engine. It describes:
- Disconnecting air inlet piping and removing bolts to detach the manifold
- Installing a new gasket and reattaching the manifold using bolts torqued to 28 Nm
- Reconnecting any disconnected components at the end of the process
This document provides instructions for disassembling and assembling the final drive of an excavator. The key steps include:
1. Removing the final drive assembly and disassembling its internal components like gears, shafts, and housings.
2. Cleaning all parts thoroughly before assembly to prevent dirt from entering mechanisms.
3. Assembling the components in reverse order and ensuring proper installation of seals and bearings, applying anti-seize compound as needed.
4. Using tools like a press and micrometer to set the bearing preload and determine the correct shim thickness.
This document provides instructions for removing and installing an exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325-A excavator engine. The procedures include removing bolts and studs, applying anti-seize compound and sealer, installing gaskets, and tightening fasteners in a specific sequence using proper torque values. Required tools are listed for each job.
Caterpillar Cat 325B L Excavator (Prefix 1GS) Service Repair Manual (1GS00001...jfkskmmdmdm
The document provides disassembly and assembly instructions for the final drive of a 325B L excavator. It details 33 steps to disassemble the final drive components including removing carriers, gears, seals and bearings. It also outlines 28 steps for reassembling the final drive, including pressing in bearings, determining the correct shim thickness, installing seals and gears, and torquing bolts. Tools and torque specifications are provided. The purpose is to provide maintenance technicians with a procedure to fully disassemble and reassemble the excavator's final drive system.
Caterpillar Cat 325B L Excavator (Prefix 6DN) Service Repair Manual (6DN00001...jfkskmmdmdm
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 325B L excavator engine. It describes:
- Disconnecting air inlet piping and removing bolts to detach the manifold
- Installing a new gasket and reattaching the manifold using bolts torqued to 28 Nm
- Reconnecting any disconnected components at the end of the process
More Related Content
Similar to Caterpillar Cat 325B LN Excavator (Prefix 6DN) Service Repair Manual (6DN00001 and up).pdf
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...jdksmmdmdd
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...fujkse9didkke3
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar cat 325 track type excavator (prefix 7 cj) service repair manual ...diskkdkdmdm
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...fjkdksmmdm
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids. Referenced tools and their part numbers are listed.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...fjkdksmmdm
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...orrf0370383
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fuusejkddmmd3e
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fuusejkddmmd3e
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...dujkdksmdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...jdksmmdmdd
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...dujkdksmdmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...jdksmmdmdd
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar cat 325 l track type excavator service repair manual (6kk00001 an...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Similar to Caterpillar Cat 325B LN Excavator (Prefix 6DN) Service Repair Manual (6DN00001 and up).pdf (16)
DAEWOO DOOSAN MEGA 160TC TIER-II WHEEL LOADER Parts Catalogue Manual.pdfjfkskmmdmdm
The document provides a parts list and diagrams for components of a MEGA 160TC TIER-II engine. It includes lists of cylinder block, timing gear case, flywheel housing, crankshaft, and cylinder head parts with part numbers, descriptions, quantities, serial numbers and replacement part information. The parts are identified by key numbers on diagrams of each engine component.
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 325B L excavator engine. It describes:
- Disconnecting air inlet piping and removing bolts to detach the manifold
- Installing a new gasket and reattaching the manifold using bolts torqued to 28 Nm
- Reconnecting any disconnected components at the end of the process
This document provides instructions for disassembling and assembling the final drive of an excavator. The key steps include:
1. Removing the final drive assembly and disassembling its internal components like gears, shafts, and housings.
2. Cleaning all parts thoroughly before assembly to prevent dirt from entering mechanisms.
3. Assembling the components in reverse order and ensuring proper installation of seals and bearings, applying anti-seize compound as needed.
4. Using tools like a press and micrometer to set the bearing preload and determine the correct shim thickness.
This document provides instructions for removing and installing an exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325-A excavator engine. The procedures include removing bolts and studs, applying anti-seize compound and sealer, installing gaskets, and tightening fasteners in a specific sequence using proper torque values. Required tools are listed for each job.
Caterpillar Cat 325B L Excavator (Prefix 1GS) Service Repair Manual (1GS00001...jfkskmmdmdm
The document provides disassembly and assembly instructions for the final drive of a 325B L excavator. It details 33 steps to disassemble the final drive components including removing carriers, gears, seals and bearings. It also outlines 28 steps for reassembling the final drive, including pressing in bearings, determining the correct shim thickness, installing seals and gears, and torquing bolts. Tools and torque specifications are provided. The purpose is to provide maintenance technicians with a procedure to fully disassemble and reassemble the excavator's final drive system.
Caterpillar Cat 325B L Excavator (Prefix 6DN) Service Repair Manual (6DN00001...jfkskmmdmdm
This document provides instructions for removing and installing an inlet manifold on a Caterpillar 325B L excavator engine. It describes:
- Disconnecting air inlet piping and removing bolts to detach the manifold
- Installing a new gasket and reattaching the manifold using bolts torqued to 28 Nm
- Reconnecting any disconnected components at the end of the process
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar Cat 325-A TRACK TYPE EXCAVATOR (Prefix 8NL) Service Repair Manual...jfkskmmdmdm
This document provides instructions for removing and installing a governor and fuel injection control linkage on a Caterpillar 325-A excavator powered by a 3116 engine. It describes the required tools and gives step-by-step procedures and illustrations for removing the governor, installing a new governor, removing the fuel injection control linkage, and installing the fuel injection control linkage. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar Cat 325-A TRACK TYPE EXCAVATOR (Prefix 8JG) Service Repair Manual...jfkskmmdmdm
This document provides instructions for removing and installing exhaust manifolds and inlet manifolds on Caterpillar 325 and 325L excavators powered by 3116 engines. It describes the required tools and outlines the step-by-step procedures for removing and installing exhaust manifolds, removing inlet manifolds, and installing inlet manifolds. It also provides instructions for removing and installing inlet and exhaust valves from the cylinder head assembly.
Caterpillar Cat 325-A FM L EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM0...jfkskmmdmdm
This document provides disassembly instructions for travel motors on 325, 325B, and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer, piston shoes, shaft assembly, seals, and other components. Special care must be taken to keep components in order and avoid damage during disassembly.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325 excavator engine. The removal procedure involves using a valve guide driver tool to push the guides out of the cylinder head from the intake/exhaust ports. For installation, new guides are lubricated and driven into the cylinder head with the driver tool. The instructions emphasize keeping parts clean to prevent wear and shortening component life.
Caterpillar Cat 325-A FM L EXCAVATOR (Prefix 7LM) Service Repair Manual (7LM0...jfkskmmdmdm
This document provides instructions for removing and installing an exhaust manifold and inlet and exhaust valves on a 325-A FM L EXCAVATOR 7LM. It describes:
1) Removing the bolts, exhaust manifold, and gaskets from the cylinder head to remove the exhaust manifold.
2) Installing new gaskets and mounting the exhaust manifold to the cylinder head, applying anti-seize compound and torqueing bolts.
3) Removing inlet and exhaust valves by compressing springs, removing retainers and springs, and removing seals and valves.
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The instructions conclude by stating to install the valve mechanism cover by referring to another section of the repair manual.
This document provides disassembly instructions for the travel motor on 325, 325B and 325L excavators. It describes 24 steps to fully disassemble the travel motor, including removing the head, brake piston, barrel assembly, shoe retainer and other components. Technicians are instructed to clean parts thoroughly, apply identifying marks, and note the original positions of components to ensure proper reassembly. Safety precautions are outlined for containing fluids and disposing of them properly.
Caterpillar Cat 325 L EXCAVATOR (Prefix 9ZK) Service Repair Manual (9ZK00001 ...jfkskmmdmdm
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using various tools to compress springs, extract components, and install new parts. Safety notices are provided to keep components clean and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valve guides on a Caterpillar 325-A excavator engine. The procedure involves using specialized tools to press the valve guides out of and back into the cylinder head assembly. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable components. The process includes lubricating and inserting the valves back into the guides once installed.
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using specific tools to compress springs, extract components, and install replacement parts. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 8NL) Service Repair Manual (...jfkskmmdmdm
This service repair manual provides instructions for installing a governor on a Caterpillar 3116 engine that powers 325 and 325L excavators. It details cleaning and lubricating parts, placing seals and the governor in the cylinder head, installing clips and pins to connect components, and setting fuel settings using specialized tools. The document provides illustrations and numbered steps for the installation process and refers to other manuals for additional guidance.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 8JG) Service Repair Manual (...jfkskmmdmdm
This document provides instructions for removing and installing exhaust manifolds and inlet manifolds on Caterpillar 325 and 325L excavators powered by 3116 engines. It describes the required tools and outlines the step-by-step procedures for removing components like bolts, studs, gaskets and manifolds. The installation section specifies applying anti-seize compound and sealer, installing new gaskets, bolts and manifolds, and tightening to the specified torques. It also includes warnings about keeping components clean and containing fluids.
This document provides instructions for removing and installing an exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325-A excavator engine. The procedures include removing bolts and studs, applying anti-seize compound and sealer, installing gaskets, and tightening fasteners in a specific sequence using proper torque values. Required tools are listed for each job.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01328419
Inlet Manifold - Remove
SMCS - 1058-011
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Dispose of all fluids according to local regulations and mandates.
1. Disconnect air inlet piping from the turbocharger to the aftercooler, if necessary.
Illustration 1 g00629952
2. Remove bolts (1) and disconnect air inlet heater solenoid (3).
3. Remove air inlet elbows (2) from air inlet manifold (5).
4. Remove bolts (4) from air inlet manifold (5).
5. Remove air inlet manifold (5) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:22:09 UTC+0800 2020
2/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01414226
Inlet Manifold - Install
SMCS - 1058-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00675794
1. Install a new gasket (6) on the cylinder head.
Illustration 2 g00629952
2. Position the air inlet manifold (5) on the engine.
3. Install bolts (4). Tighten the bolts to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
4. Install air inlet elbows (2) on air inlet manifold (5).
5. Install bolts (1) and connect air inlet heater solenoid (3).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:23:04 UTC+0800 2020
2/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01943334
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
1/5
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01011225
Note: The following components of the exhaust valves are different from the components of
the inlet valves: spring retainer (2), valve spring (3) and valve (5).
Illustration 2 g01011269
1. Use Tooling (A) to compress valve spring (3). Remove retainer lock (1).
2. Remove Tooling (A).
3. Remove spring retainer (2). Remove valve spring (3).
2/5
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 4. Remove valve seal (4) and valve (5).
5. Repeat Steps 1 through 4 in order to remove the remaining inlet valves and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
3/5
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g01011225
1. Lubricate valve (5) with clean engine oil. Install valve (5) in the cylinder head assembly.
Install new valve seal (4) against the valve guide.
2. Place the following items on the valve stem: valve spring (3) and spring retainer (2).
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
Note: A small amount of grease can be used to hold retainer locks (1) in position during
installation.
4/5
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 4 g01011269
3. Use Tooling (A) to compress valve spring (3). Install retainer lock (1).
4. Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves.
End By:
a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:24:00 UTC+0800 2020
5/5
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01961680
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Asseblies 3114, 3116, and
3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162, "Procedure
to Measure and Salvage Cylinder Head Assemblies and Related Components".
1/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00745735
Typical example
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (A) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
B 1U-7792 Guide Collar (1)
1
C 9U-6895 Valve Guide Driver 1
D 149-4008 Guide Collar 1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 2 g00745782
Typical example
1. Position inlet valve guide (1) and tap on the top of inlet valve guide (1). This is done in
order to start inlet valve guide (1) into the cylinder head assembly.
2. Use Tooling (A) and Tooling (B) to install inlet valve guide (1). Install inlet valve guides
(1) until tooling (B) contacts the cylinder head.
3/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g00745672
Typical example
3. Position exhaust valve guide (2) and tap on the top of exhaust valve guide (2). This is done
in order to start the exhaust valve guide into the cylinder head assembly.
Note: Some of the early engines have inlet valves and exhaust valves that are identical in
size. Use the same specifications and the same tools for both valves. Proceed to Step 4 if the
valves are not the same size.
4. Use Tooling (C) and Tooling (D) to install exhaust valve guide (2). Install inlet valve guides
(2) until tooling (D) contacts the cylinder head.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:24:56 UTC+0800 2020
4/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929146
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor 1
B(1)
165-5647 Valve Seat Extractor 1
C(1)
6V-4804 Handle 1
D(1)
6V-4192 Threaded Shaft 1
E(1)
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
Illustration 1 g00615519
Illustration 2 g00656459
Note: Replace Tooling (A) with Tooling (B) for the removal of the inlet valve seat insert.
1. Install Tooling (A) in the exhaust valve seat insert.
2. Install Tooling (C) and Tooling (D) in Tooling (A). Hand tighten Tooling (D). Tooling (A)
will expand below the edge of valve seat insert (1).
2/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00656462
3. Install Tooling (E) on the cylinder head under Tooling (C). Hold Tooling (D) while you turn
Tooling (C). Remove valve seat insert (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
F 1U-6685 Guide and Insert Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
1. Cool the valve seat inserts for easier installation.
3/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 4 g01003799
2. Turn Tooling (F) upside-down and use Tooling (F) and a press to install the valve seat
inserts in the cylinder head assembly.
3. After the valve seat inserts are installed, grind the inserts to the final specification. Refer to
Guideline for Reusable Parts and Salvage Operation, SEBF8218, "Specifications for
Cylinder Head Assemblies 3114, 3116, and 3126 Engines" for the specifications.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:25:52 UTC+0800 2020
4/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929163
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
Start By:
a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01009468
1. Use Tooling (A) to remove engine oil filter (3).
2. Disconnect the tube assembly for the turbocharger inlet (1) from the engine oil filter base
(4).
3. Remove bolts (2) and the washers that hold engine oil filter base (4) to the cylinder block.
4. Remove engine oil filter base (4) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:26:48 UTC+0800 2020
2/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929612
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Illustration 1 g01011623
Personal injury can result from being struck by parts propelled by a
released spring force.
1/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plugs (1) and (3) from oil filter base (2).
Illustration 2 g01011627
2. Remove springs (4) and valves (6). Remove O-ring seals (5) from plugs (1) and (3). Inspect
the parts for wear or damage. If the parts are worn or damaged, use new parts for
replacement.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:27:43 UTC+0800 2020
2/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929615
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
Illustration 1 g01011627
1. Install O-ring seals (5) onto plugs (1) and (3). Install valves (6) and springs (4).
1/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 2 g01011623
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install plugs (1) and (3) onto oil filter base (2).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:28:39 UTC+0800 2020
2/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02376426
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01009468
1/3
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...