This document provides instructions for removing and installing an exhaust manifold, inlet manifold, valves, and valve guides on a 325B L excavator powered by a 3116 engine. The removal and installation procedures are described in steps and include required tools. Illustrations are provided to show typical examples.
Caterpillar cat 325 b l excavator (prefix 4ds) service repair manual (4ds0000...fjjskekdmme
This document provides instructions for removing and installing an exhaust manifold on a 325B L excavator powered by a 3116 engine. The removal procedure involves removing bolts and gaskets from the cylinder head assembly. The installation procedure specifies applying anti-seize compound to mounting studs and high temperature sealer if the manifold has multiple pieces, installing new gaskets, and tightening bolts to the specified torques. Tools required are also listed.
Caterpillar cat 325 b ln excavator (prefix 4ds) service repair manual (4ds000...fjjskekdmme
This document provides instructions for removing and installing an exhaust manifold on a 325B L & 325B LN excavator powered by a 3116 engine. The removal procedure involves removing bolts and gaskets from the cylinder head assembly. The installation procedure specifies applying anti-seize compound to mounting studs and bolts, installing new gaskets, and tightening bolts to the specified torques. Tools and torque specifications are provided. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting relevant components, removing mounting hardware, and replacing gaskets. Precautions are listed to prevent contamination and contain fluids. Required tools are also identified.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting relevant components, removing mounting hardware, and replacing gaskets. Precautions are outlined to prevent contamination and contain fluids. Required tools are listed for each job.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing mounting hardware, applying sealant or anti-seize compound, and torquing bolts to the specified values. Tools required are also listed. Following the procedures properly helps prevent contamination and contain fluids.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing bolts and studs, applying sealant, and torquing fasteners to the specified values. Tools required are also listed. Following the provided steps helps ensure components are properly disassembled and reassembled.
Caterpillar cat 325 l excavator (prefix 2sk) service repair manual (2sk00001 ...diskkdkdmdm
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing mounting hardware, applying sealant or anti-seize compound, and torquing bolts to the specified values. Tools required are also listed. Following the provided steps helps ensure components are properly disassembled and reassembled.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting relevant components, removing bolts and other fasteners, applying sealant if needed, and reinstalling components in reverse order while torquing bolts to the specified values. Tools required are also listed for each procedure.
Caterpillar cat 325 b l excavator (prefix 4ds) service repair manual (4ds0000...fjjskekdmme
This document provides instructions for removing and installing an exhaust manifold on a 325B L excavator powered by a 3116 engine. The removal procedure involves removing bolts and gaskets from the cylinder head assembly. The installation procedure specifies applying anti-seize compound to mounting studs and high temperature sealer if the manifold has multiple pieces, installing new gaskets, and tightening bolts to the specified torques. Tools required are also listed.
Caterpillar cat 325 b ln excavator (prefix 4ds) service repair manual (4ds000...fjjskekdmme
This document provides instructions for removing and installing an exhaust manifold on a 325B L & 325B LN excavator powered by a 3116 engine. The removal procedure involves removing bolts and gaskets from the cylinder head assembly. The installation procedure specifies applying anti-seize compound to mounting studs and bolts, installing new gaskets, and tightening bolts to the specified torques. Tools and torque specifications are provided. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting relevant components, removing mounting hardware, and replacing gaskets. Precautions are listed to prevent contamination and contain fluids. Required tools are also identified.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting relevant components, removing mounting hardware, and replacing gaskets. Precautions are outlined to prevent contamination and contain fluids. Required tools are listed for each job.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing mounting hardware, applying sealant or anti-seize compound, and torquing bolts to the specified values. Tools required are also listed. Following the procedures properly helps prevent contamination and contain fluids.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing bolts and studs, applying sealant, and torquing fasteners to the specified values. Tools required are also listed. Following the provided steps helps ensure components are properly disassembled and reassembled.
Caterpillar cat 325 l excavator (prefix 2sk) service repair manual (2sk00001 ...diskkdkdmdm
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing mounting hardware, applying sealant or anti-seize compound, and torquing bolts to the specified values. Tools required are also listed. Following the provided steps helps ensure components are properly disassembled and reassembled.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting relevant components, removing bolts and other fasteners, applying sealant if needed, and reinstalling components in reverse order while torquing bolts to the specified values. Tools required are also listed for each procedure.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing mounting hardware, applying sealant or anti-seize compound, and torquing bolts to the specified values. Tools required are also listed. Following the provided steps helps ensure components are properly disassembled and reassembled.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. It describes removing components like bolts, studs, gaskets and manifolds. It also details installing new gaskets and reinstalling components, noting specific torques for bolts. Tools required are listed for tasks like compressing valve springs during valve removal and installation.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. It describes removing components like bolts, studs, gaskets and manifolds. It also details installing new gaskets and torquing bolts to the specified values. Tools needed are listed along with maintenance notices to keep parts clean and contain fluids.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. It describes removing components like bolts, studs, gaskets and manifolds. It also details installing new gaskets and reinstalling components, noting specific torques for bolts. Tools required are listed for tasks like compressing valve springs during valve removal and installation.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The procedures include removing bolts and studs, applying anti-seize compound and sealer, installing gaskets, and tightening components to the specified torques. Tools required are also listed. Following the provided steps helps ensure proper disassembly and reassembly of these engine components.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing mounting hardware, applying sealant or anti-seize compound, and torquing bolts to the specified values. Tools required are also listed. Following the provided steps helps ensure components are properly disassembled and reassembled.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting relevant components, removing mounting hardware, and replacing gaskets. Precautions are outlined to prevent contamination and contain fluids. Required tools are listed for each job.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. It describes removing components like bolts, studs, gaskets and manifolds. It also details installing new gaskets and reinstalling components, noting specific torques for bolts. Tools required are listed for tasks like compressing valve springs during valve removal and installation.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing mounting hardware, applying sealant or anti-seize compound, and torquing bolts to the specified values. Tools required are also listed. Following the procedures properly helps prevent contamination and contain fluids.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting relevant components, removing mounting hardware, and replacing gaskets. Precautions are outlined to prevent contamination and contain fluids. Required tools are listed for each job.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing bolts and studs, applying sealant, and torquing fasteners to the specified values. Tools required are also listed. Following the procedures helps ensure components are properly disassembled and reassembled.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. It describes removing components like bolts, studs, gaskets and manifolds. It also details installing new gaskets and reinstalling components, noting specific torques for bolts. Tools required are listed for tasks like compressing valve springs during valve removal and installation.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting relevant components, removing mounting hardware, and replacing gaskets. Precautions are listed to prevent contamination and contain fluids. Required tools are also identified.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing mounting hardware, applying sealant or anti-seize compound, and torquing bolts to the specified values. Tools required are also listed. Following the procedures properly helps prevent contamination and contain fluids.
Clark C500, Y180 Forklift Service Repair Manual.pdfdjdksmmdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and lists parts, components, and procedures for repair and maintenance. Copyrighted material is not to be distributed. The index includes sections on engines, transmissions, hydraulics, electrical systems, brakes, steering and other components. Safety practices and proper maintenance procedures are outlined to avoid injury and ensure safe operation.
Clark C500, Y250S Forklift Service Repair Manual.pdfdjdksmmdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and should not be distributed. The document contains diagrams and descriptions of various forklift components and systems, grouped by number. Safety warnings and instructions for safe maintenance practices are also provided.
The document provides maintenance and safety information for a Clark lift truck model SM-560. It includes sections on safety signs and messages, user safe maintenance practices, and a planned maintenance program. The planned maintenance program outlines periodic inspections and maintenance tasks that should be performed, including inspecting nameplates, wheels and tires, controls, brakes, steering, batteries, and mechanisms. It stresses the importance of a clean lift truck and testing all functions before returning the truck to operation.
Clark TMG 12-25 Forklift Service Repair Manual.pdfdjdksmmdmd
This document is a service manual for Clark forklifts that contains information on safely maintaining the forklifts. It includes sections on safety procedures, periodic maintenance schedules, specifications for various parts, and procedures for servicing components such as motors, hydraulics, brakes, steering, and other systems. The manual uses a standardized grouping and numbering system to organize the content and make specific information easy to locate.
Clark TMG 13-20X Forklift Service Repair Manual.pdfdjdksmmdmd
This document provides a summary of safe maintenance practices for industrial trucks. It discusses safety signs and messages used in service manuals. Proper ventilation, fire safety, and authorized personnel are important. Before working on a truck, raise the wheels, disconnect the battery, and check for fuel and electrical hazards. Replacements parts must meet manufacturer standards. Modifications require approval. Overall, maintenance should follow manufacturer procedures to ensure safety.
Komatsu SK815-5 Skid Steer Loader Service Repair Manual (SN 37BF00902 and up)...djdksmmdmd
This shop manual provides instructions for servicing Komatsu skid-steer loaders models SK714-5, SK815-5, and SK815-5 turbo. It is divided into sections covering the machine's structure and function, testing and adjusting procedures, disassembly and assembly instructions, and maintenance standards. Safety precautions are prominently featured to ensure workers' safety during repair operations.
John Deere Alternators & Starter Motors Service Repair Manual.pdfdjdksmmdmd
This document is a Component Technical Manual from Deere & Company that provides service information for alternators and starter motors. It contains sections on safety, general information, and electrical system basics. The safety section outlines proper procedures and precautions for working on electrical components, including preventing battery explosions, handling fluids safely, and wearing protective equipment.
John Deere 12PC Walk-Behind Mower Service Repair Manual.pdfdjdksmmdmd
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications for various mower models, repair specifications for engines and components, information on fuels and lubricants, and locations for serial numbers. The document outlines sections on general information, engine repair, fuel and air systems, electrical systems, power trains, tests and adjustments, and miscellaneous repair items. It provides technicians with the information needed to service the components, diagnose issues, and perform repairs on the mowers.
More Related Content
Similar to Caterpillar Cat 325B LN Excavator (Prefix 4DS) Service Repair Manual (4DS00001 and up).pdf
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing mounting hardware, applying sealant or anti-seize compound, and torquing bolts to the specified values. Tools required are also listed. Following the provided steps helps ensure components are properly disassembled and reassembled.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. It describes removing components like bolts, studs, gaskets and manifolds. It also details installing new gaskets and reinstalling components, noting specific torques for bolts. Tools required are listed for tasks like compressing valve springs during valve removal and installation.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. It describes removing components like bolts, studs, gaskets and manifolds. It also details installing new gaskets and torquing bolts to the specified values. Tools needed are listed along with maintenance notices to keep parts clean and contain fluids.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. It describes removing components like bolts, studs, gaskets and manifolds. It also details installing new gaskets and reinstalling components, noting specific torques for bolts. Tools required are listed for tasks like compressing valve springs during valve removal and installation.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The procedures include removing bolts and studs, applying anti-seize compound and sealer, installing gaskets, and tightening components to the specified torques. Tools required are also listed. Following the provided steps helps ensure proper disassembly and reassembly of these engine components.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing mounting hardware, applying sealant or anti-seize compound, and torquing bolts to the specified values. Tools required are also listed. Following the provided steps helps ensure components are properly disassembled and reassembled.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting relevant components, removing mounting hardware, and replacing gaskets. Precautions are outlined to prevent contamination and contain fluids. Required tools are listed for each job.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. It describes removing components like bolts, studs, gaskets and manifolds. It also details installing new gaskets and reinstalling components, noting specific torques for bolts. Tools required are listed for tasks like compressing valve springs during valve removal and installation.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing mounting hardware, applying sealant or anti-seize compound, and torquing bolts to the specified values. Tools required are also listed. Following the procedures properly helps prevent contamination and contain fluids.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting relevant components, removing mounting hardware, and replacing gaskets. Precautions are outlined to prevent contamination and contain fluids. Required tools are listed for each job.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing bolts and studs, applying sealant, and torquing fasteners to the specified values. Tools required are also listed. Following the procedures helps ensure components are properly disassembled and reassembled.
This document provides instructions for removing and installing exhaust manifolds, inlet manifolds, and inlet/exhaust valves on Caterpillar 325, 325L, and 325LN excavators powered by 3116 engines. It describes removing components like bolts, studs, gaskets and manifolds. It also details installing new gaskets and reinstalling components, noting specific torques for bolts. Tools required are listed for tasks like compressing valve springs during valve removal and installation.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting relevant components, removing mounting hardware, and replacing gaskets. Precautions are listed to prevent contamination and contain fluids. Required tools are also identified.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on a Caterpillar 325 excavator. The removal and installation procedures include disconnecting components, removing mounting hardware, applying sealant or anti-seize compound, and torquing bolts to the specified values. Tools required are also listed. Following the procedures properly helps prevent contamination and contain fluids.
Similar to Caterpillar Cat 325B LN Excavator (Prefix 4DS) Service Repair Manual (4DS00001 and up).pdf (14)
Clark C500, Y180 Forklift Service Repair Manual.pdfdjdksmmdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and lists parts, components, and procedures for repair and maintenance. Copyrighted material is not to be distributed. The index includes sections on engines, transmissions, hydraulics, electrical systems, brakes, steering and other components. Safety practices and proper maintenance procedures are outlined to avoid injury and ensure safe operation.
Clark C500, Y250S Forklift Service Repair Manual.pdfdjdksmmdmd
This document contains a pictorial index and maintenance instructions for Clark forklifts. It is intended only for Clark dealers and should not be distributed. The document contains diagrams and descriptions of various forklift components and systems, grouped by number. Safety warnings and instructions for safe maintenance practices are also provided.
The document provides maintenance and safety information for a Clark lift truck model SM-560. It includes sections on safety signs and messages, user safe maintenance practices, and a planned maintenance program. The planned maintenance program outlines periodic inspections and maintenance tasks that should be performed, including inspecting nameplates, wheels and tires, controls, brakes, steering, batteries, and mechanisms. It stresses the importance of a clean lift truck and testing all functions before returning the truck to operation.
Clark TMG 12-25 Forklift Service Repair Manual.pdfdjdksmmdmd
This document is a service manual for Clark forklifts that contains information on safely maintaining the forklifts. It includes sections on safety procedures, periodic maintenance schedules, specifications for various parts, and procedures for servicing components such as motors, hydraulics, brakes, steering, and other systems. The manual uses a standardized grouping and numbering system to organize the content and make specific information easy to locate.
Clark TMG 13-20X Forklift Service Repair Manual.pdfdjdksmmdmd
This document provides a summary of safe maintenance practices for industrial trucks. It discusses safety signs and messages used in service manuals. Proper ventilation, fire safety, and authorized personnel are important. Before working on a truck, raise the wheels, disconnect the battery, and check for fuel and electrical hazards. Replacements parts must meet manufacturer standards. Modifications require approval. Overall, maintenance should follow manufacturer procedures to ensure safety.
Komatsu SK815-5 Skid Steer Loader Service Repair Manual (SN 37BF00902 and up)...djdksmmdmd
This shop manual provides instructions for servicing Komatsu skid-steer loaders models SK714-5, SK815-5, and SK815-5 turbo. It is divided into sections covering the machine's structure and function, testing and adjusting procedures, disassembly and assembly instructions, and maintenance standards. Safety precautions are prominently featured to ensure workers' safety during repair operations.
John Deere Alternators & Starter Motors Service Repair Manual.pdfdjdksmmdmd
This document is a Component Technical Manual from Deere & Company that provides service information for alternators and starter motors. It contains sections on safety, general information, and electrical system basics. The safety section outlines proper procedures and precautions for working on electrical components, including preventing battery explosions, handling fluids safely, and wearing protective equipment.
John Deere 12PC Walk-Behind Mower Service Repair Manual.pdfdjdksmmdmd
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications for various mower models, repair specifications for engines and components, information on fuels and lubricants, and locations for serial numbers. The document outlines sections on general information, engine repair, fuel and air systems, electrical systems, power trains, tests and adjustments, and miscellaneous repair items. It provides technicians with the information needed to service the components, diagnose issues, and perform repairs on the mowers.
John Deere 12PB Walk-Behind Mower Service Repair Manual.pdfdjdksmmdmd
This document contains sections and groups related to service information for John Deere 21-inch rear discharge walk-behind rotary mowers. It includes specifications for various mower models, repair specifications for engines and components, information on fuels and lubricants, and locations for identifying serial numbers. The document outlines sections for engine repair, fuel/air systems, electrical systems, power trains, tests and adjustments, and miscellaneous repairs. It provides technicians with information needed for diagnosis, repair, and maintenance of the mowers.
John Deere 5E 2BV Blower Service Repair Manual.pdfdjdksmmdmd
The document provides specifications for the 5E and 2BV blowers, including engine details like displacement, bore, stroke, compression ratio, carburetor, lubrication, fuel, idle and operating speeds, starter, ignition system, spark plug, magneto air gap, and fuel tank capacities. It also lists the blower type as centrifugal and single stage.
John Deere 3-179D OEM Engine Service Repair Manual.pdfdjdksmmdmd
This document provides an overview and table of contents for a technical manual covering 300 Series OEM Engines. It includes:
- Sections covering the engine and its components, auxiliary systems, electrical systems, sheet metal, PTO drive, and system testing.
- An index listing components and procedures alphabetically to aid navigation.
- Specification tables for torque values and engine data.
The manual is intended as a reference for experienced technicians servicing these engines, with concise instructions and specifications rather than theoretical background.
This document provides specifications, maintenance schedules, adjustment procedures, and safety information for Clark PT-5, PT-7, PTT-5, and PTT-7 trucks. It outlines an essential planned maintenance program to keep the trucks safely operating, including inspections, operational checks, cleaning, lubrication, and adjustments. The document emphasizes safety practices for maintenance, such as raising the wheels, disconnecting power, and using blocks before working under lifted components.
Kubota BX1500D Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions for using a parts book for an engine. It explains the column headings in parts book pages including reference number, part number, description, quantity, serial number range and interchangeability. It also notes country codes that may be included and what they represent. An example page from the parts book is then shown listing the specific parts for an engine with the corresponding information.
Clark EPG 15-18 Forklift Service Repair Manual.pdfdjdksmmdmd
This document is a service manual for Clark forklifts that contains information on safely maintaining the forklifts. It includes sections on safety procedures, periodic maintenance schedules, specifications for parts, and procedures for servicing various systems of the forklift such as the battery, wiring, motors, brakes, hydraulics, tilt cylinders, and more. The document uses a standardized grouping and numbering system to organize the content and make specific sections and pages easy to locate.
Kubota BX2230D Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions and part numbers for a parts book. It defines the column headings used on part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes that may be included and their meanings. The remainder of the document lists specific part numbers and descriptions for a BX2230D tractor organized by system or component.
Kubota L35 Tractor Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions and definitions for parts books. It explains that the heading on parts pages will match the picture page. It defines the column headings for part number pages including reference number, part number, description, quantity, serial number range and interchangeability. It notes country codes that may be included and their meanings. Finally, it provides an index of all product parts for reference L35 and lists the relevant parts book for each item.
Kubota G4200H Lawn mower Parts Catalogue Manual.pdfdjdksmmdmd
The document provides instructions for parts books, including definitions of column headings in parts number pages and notes about country codes. It then provides a sample page from a parts book for a G4200H product that lists over 200 individual part numbers, descriptions, quantities, serial number ranges, interchangeability, remarks and weights.
Komatsu SK714-5 Skid Steer Loader Service Repair Manual (SN 37AF01876 and up)...djdksmmdmd
This document provides shop manual instructions for adjusting valve clearance on Komatsu skid-steer loaders models SK714-5, SK815-5, and SK815-5 turbo. The instructions include removing covers to access the valves, rotating the drive shaft to specific positions, checking valve clearance with feeler gauges, adjusting clearance by turning screws, and reassembling covers. Clearance specifications and tightening torques are provided. The document also provides a zero setting procedure for the SK815-5 turbo model before performing the clearance adjustment.
John Deere Yanmar Engines 322, F912, F932 Service Repair Manual.pdfdjdksmmdmd
This document is a component technical manual for Yanmar gasoline engines. It contains instructions for repairing engines, fuel systems, and electrical systems. It also includes theory of operation, diagnostic procedures, and testing procedures. The manual should be used along with the machine's technical manual for information on removing and installing the engine, and accessing engine components. The manual emphasizes safety and provides illustrated, step-by-step instructions for diagnosis and repair of engine systems.
John Deere POWERTECH 4.5L & 6.8L Diesel Engines Base Engine Service Repair Ma...djdksmmdmd
This document provides instructions for servicing Powertech 4.5L and 6.8L diesel engines. It outlines five technical manuals that cover different aspects of the engines, with this document focusing on the base engine. The introduction provides safety information and explains how to use the manual, including cleaning the engine before repair. It directs technicians to companion manuals for fuel system repair, operation and diagnostics based on the specific fuel system for the engine being serviced.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 4DS
Configuration: 325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01928788
Exhaust Manifold - Remove and Install
SMCS - 1059-010
Removal Procedure
Start By:
a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
Illustration 1 g00652578
Typical example
1. Remove bolts (1), exhaust manifold (2), locks and the gaskets from the cylinder head
assembly.
2. If the engine is equipped with a three-piece exhaust manifold, disassemble exhaust manifold
(2) into three pieces.
3. Remove mounting studs (3) from exhaust manifold (2), if necessary.
1/4
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-3931 Anti-Seize Compound 1
B 2P-2333 High Temperature Sealer 1
Illustration 2 g00652578
Typical example
1. Apply Tooling (A) to the threads of mounting studs (3).
2. Install mounting studs (3). Tighten mounting studs (3) to a torque of 35 ± 5 N·m
(26 ± 4 lb ft).
3. If the engine is equipped with a three-piece exhaust manifold, apply a thin coat of Tooling
(B) to the male ends of exhaust manifold (2). Coat the inside of the female ends of exhaust
manifold (2) with clean engine oil. Assemble exhaust manifold (2) and remove the excess
sealant from the joints.
4. Install new exhaust manifold gaskets.
5. Apply Tooling (A) to the threads of bolts (1). Position the gaskets and exhaust manifold (2)
on the cylinder head assembly. Install locks and bolts (1).
2/4
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00617739
Typical example of a three-piece exhaust manifold
Illustration 4 g00641026
Exhaust manifold for a Four cylinder engine
3/4
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 5 g00641092
Water cooled exhaust manifold
6. Tighten bolts (1) in a numerical sequence to a torque of 4 ± 1 N·m (35 ± 9 lb in).
7. Tighten bolts (1) in a numerical sequence to a torque of 45 ± 5 N·m (33 ± 4 lb ft).
Illustration 6 g00675760
Typical example of locking tabs
8. Bend the locking tabs (4) over the flat of each bolt head.
End By:
a. Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 19:27:10 UTC+0800 2020
4/4
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 4DS
Configuration: 325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01328419
Inlet Manifold - Remove
SMCS - 1058-011
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/2
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Dispose of all fluids according to local regulations and mandates.
1. Disconnect air inlet piping from the turbocharger to the aftercooler, if necessary.
Illustration 1 g00629952
2. Remove bolts (1) and disconnect air inlet heater solenoid (3).
3. Remove air inlet elbows (2) from air inlet manifold (5).
4. Remove bolts (4) from air inlet manifold (5).
5. Remove air inlet manifold (5) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 19:28:06 UTC+0800 2020
2/2
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 4DS
Configuration: 325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01414226
Inlet Manifold - Install
SMCS - 1058-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g00675794
1. Install a new gasket (6) on the cylinder head.
Illustration 2 g00629952
2. Position the air inlet manifold (5) on the engine.
3. Install bolts (4). Tighten the bolts to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
4. Install air inlet elbows (2) on air inlet manifold (5).
5. Install bolts (1) and connect air inlet heater solenoid (3).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 19:29:02 UTC+0800 2020
2/2
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 4DS
Configuration: 325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01943334
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
1/5
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g01011225
Note: The following components of the exhaust valves are different from the components of
the inlet valves: spring retainer (2), valve spring (3) and valve (5).
Illustration 2 g01011269
1. Use Tooling (A) to compress valve spring (3). Remove retainer lock (1).
2. Remove Tooling (A).
3. Remove spring retainer (2). Remove valve spring (3).
2/5
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 4. Remove valve seal (4) and valve (5).
5. Repeat Steps 1 through 4 in order to remove the remaining inlet valves and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
3/5
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 3 g01011225
1. Lubricate valve (5) with clean engine oil. Install valve (5) in the cylinder head assembly.
Install new valve seal (4) against the valve guide.
2. Place the following items on the valve stem: valve spring (3) and spring retainer (2).
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
Note: A small amount of grease can be used to hold retainer locks (1) in position during
installation.
4/5
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 4 g01011269
3. Use Tooling (A) to compress valve spring (3). Install retainer lock (1).
4. Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves.
End By:
a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 19:29:58 UTC+0800 2020
5/5
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 4DS
Configuration: 325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01961680
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Asseblies 3114, 3116, and
3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162, "Procedure
to Measure and Salvage Cylinder Head Assemblies and Related Components".
1/4
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00745735
Typical example
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (A) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
B 1U-7792 Guide Collar (1)
1
C 9U-6895 Valve Guide Driver 1
D 149-4008 Guide Collar 1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 2 g00745782
Typical example
1. Position inlet valve guide (1) and tap on the top of inlet valve guide (1). This is done in
order to start inlet valve guide (1) into the cylinder head assembly.
2. Use Tooling (A) and Tooling (B) to install inlet valve guide (1). Install inlet valve guides
(1) until tooling (B) contacts the cylinder head.
3/4
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 3 g00745672
Typical example
3. Position exhaust valve guide (2) and tap on the top of exhaust valve guide (2). This is done
in order to start the exhaust valve guide into the cylinder head assembly.
Note: Some of the early engines have inlet valves and exhaust valves that are identical in
size. Use the same specifications and the same tools for both valves. Proceed to Step 4 if the
valves are not the same size.
4. Use Tooling (C) and Tooling (D) to install exhaust valve guide (2). Install inlet valve guides
(2) until tooling (D) contacts the cylinder head.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 19:30:53 UTC+0800 2020
4/4
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 4DS
Configuration: 325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929146
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor 1
B(1)
165-5647 Valve Seat Extractor 1
C(1)
6V-4804 Handle 1
D(1)
6V-4192 Threaded Shaft 1
E(1)
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
Illustration 1 g00615519
Illustration 2 g00656459
Note: Replace Tooling (A) with Tooling (B) for the removal of the inlet valve seat insert.
1. Install Tooling (A) in the exhaust valve seat insert.
2. Install Tooling (C) and Tooling (D) in Tooling (A). Hand tighten Tooling (D). Tooling (A)
will expand below the edge of valve seat insert (1).
2/4
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g00656462
3. Install Tooling (E) on the cylinder head under Tooling (C). Hold Tooling (D) while you turn
Tooling (C). Remove valve seat insert (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
F 1U-6685 Guide and Insert Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
1. Cool the valve seat inserts for easier installation.
3/4
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 4 g01003799
2. Turn Tooling (F) upside-down and use Tooling (F) and a press to install the valve seat
inserts in the cylinder head assembly.
3. After the valve seat inserts are installed, grind the inserts to the final specification. Refer to
Guideline for Reusable Parts and Salvage Operation, SEBF8218, "Specifications for
Cylinder Head Assemblies 3114, 3116, and 3126 Engines" for the specifications.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 19:31:49 UTC+0800 2020
4/4
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 4DS
Configuration: 325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929163
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
Start By:
a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01009468
1. Use Tooling (A) to remove engine oil filter (3).
2. Disconnect the tube assembly for the turbocharger inlet (1) from the engine oil filter base
(4).
3. Remove bolts (2) and the washers that hold engine oil filter base (4) to the cylinder block.
4. Remove engine oil filter base (4) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 19:32:45 UTC+0800 2020
2/2
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 4DS
Configuration: 325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929612
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Illustration 1 g01011623
Personal injury can result from being struck by parts propelled by a
released spring force.
1/2
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plugs (1) and (3) from oil filter base (2).
Illustration 2 g01011627
2. Remove springs (4) and valves (6). Remove O-ring seals (5) from plugs (1) and (3). Inspect
the parts for wear or damage. If the parts are worn or damaged, use new parts for
replacement.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 19:33:41 UTC+0800 2020
2/2
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 4DS
Configuration: 325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929615
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
Illustration 1 g01011627
1. Install O-ring seals (5) onto plugs (1) and (3). Install valves (6) and springs (4).
1/2
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 2 g01011623
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install plugs (1) and (3) onto oil filter base (2).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 19:34:37 UTC+0800 2020
2/2
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 En...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...