This document provides instructions for removing and installing inlet and exhaust valve guides on 325, 325L and 325LN excavator models powered by a 3116 engine. It outlines the required tools and gives a step-by-step process for both removing the old guides and pressing in the new ones. Proper cleaning and lubrication is emphasized to prevent premature wear of components. Salvage guidelines are referenced for determining whether guides can be reused.
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The instructions conclude by stating to install the valve mechanism cover by referring to another section of the repair manual.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on Caterpillar 325, 325L and 325LN excavator models. The procedure includes using specific tools to extract the valve seat inserts from the cylinder head. New valve seat inserts should be installed and lubricated before reinstalling the valves and valve guides. Safety precautions are provided to keep parts clean and contain fluids during the repair process.
Caterpillar Cat 325 L EXCAVATOR (Prefix 9ZK) Service Repair Manual (9ZK00001 ...f8usiejdkmdd
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using various tools to compress springs, extract components, and install new parts. Safety notices are provided to keep components clean and contain fluids.
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using specific tools to compress springs, extract components, and install replacements. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325-A, 325, 325 L AND 325 LN EXCAVATOR (Prefix 9ZK) Service R...yan77xunhao
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The final step is to install the valve mechanism cover.
Caterpillar cat 325 l excavator (prefix 9 zk) service repair manual (9zk00001...ifoseidkkd
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The final step is to install the valve mechanism cover.
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using various tools to compress springs, extract components, and install new parts. Safety notices are provided to keep components clean and contain fluids.
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The final step is to install the valve mechanism cover.
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The instructions conclude by stating to install the valve mechanism cover by referring to another section of the repair manual.
This document provides instructions for removing and installing inlet and exhaust valve seat inserts on Caterpillar 325, 325L and 325LN excavator models. The procedure includes using specific tools to extract the valve seat inserts from the cylinder head. New valve seat inserts should be installed and lubricated before reinstalling the valves and valve guides. Safety precautions are provided to keep parts clean and contain fluids during the repair process.
Caterpillar Cat 325 L EXCAVATOR (Prefix 9ZK) Service Repair Manual (9ZK00001 ...f8usiejdkmdd
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using various tools to compress springs, extract components, and install new parts. Safety notices are provided to keep components clean and contain fluids.
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using specific tools to compress springs, extract components, and install replacements. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325-A, 325, 325 L AND 325 LN EXCAVATOR (Prefix 9ZK) Service R...yan77xunhao
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The final step is to install the valve mechanism cover.
Caterpillar cat 325 l excavator (prefix 9 zk) service repair manual (9zk00001...ifoseidkkd
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The final step is to install the valve mechanism cover.
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include using various tools to compress springs, extract components, and install new parts. Safety notices are provided to keep components clean and contain fluids.
This document provides instructions for installing an inlet manifold on a 325-A excavator engine. It involves installing a new gasket on the cylinder head, positioning the air inlet manifold and installing bolts to secure it, then installing air inlet elbows and connecting the air inlet heater solenoid. The final step is to install the valve mechanism cover.
This document provides instructions for servicing components of a Caterpillar 330D L excavator engine. It describes procedures for removing and installing the cylinder head, camshaft, lifter group, and associated parts. The steps include draining coolant, removing mounting hardware, lifting components with tools, applying lubricant, and torquing fasteners to specified values. Safety notices are provided to keep parts clean and prevent damage during removal and installation.
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, shafts, seals, and housings and attaching the assembly to the excavator frame using bolts.
3. Proper cleaning, lubrication, and heating of parts is emphasized to ensure correct assembly. Tools, torque specifications, and maintenance procedures are also outlined.
Caterpillar Cat 330C L Excavator (Prefix MCA) Service Repair Manual (MCA00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The disassembly process involves removing 28 different components in a specific sequence. The assembly process reverses the disassembly steps and includes applying thread lock compound and lubricating components before reassembly. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...fjkdksmmdm
This document provides instructions for disassembling and assembling a 330C excavator travel motor. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then describes 13 steps for assembly, including installing seals, bearings, springs, cam plate, and rotating assembly into the housing. Special tools are listed and safety notices are provided throughout regarding cleaning, pressurized air, and spring loading.
Caterpillar Cat 330C L Excavator (Prefix JNK) Service Repair Manual (JNK00001...fjkdksmmdm
The document provides instructions for assembling and installing a piston motor (hydraulic fan). It is a 3 page document that details 20 steps for assembly, including installing various components like bearings, seals, springs and retaining rings. It then provides 11 steps for installing the assembled piston motor and attaching hoses and guards. Proper cleaning and lubrication of parts is emphasized.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...fjkdksmmdm
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by listing the required tools. The instructions then state to clean all parts, set the number 1 piston to top center, and align the camshaft and idler gears. The camshaft is then lubricated and inserted into the cylinder block. The thrust plate and bolts are installed and tightened. Lifters are repositioned and the procedure ends by installing the front cover and rocker arm assembly.
Caterpillar Cat 330C L Excavator (Prefix JCD) Service Repair Manual (JCD00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavators. It outlines 28 steps for disassembly, removing components like the head, springs, brake piston, and bearings. It then outlines 13 steps for assembly, replacing seals and installing components in the reverse order of disassembly, taking care to mark parts and return them to their original positions. Special tools are listed that may be required for tasks like removing races and seals.
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and seals. It then describes 15 steps for reassembling the motor and installing components in the reverse order, making sure to clean parts and apply thread lock compound as needed. Tools required include retaining ring pliers, a bearing puller, an eyebolt, and an adapter.
Caterpillar Cat 330C L Excavator (Prefix GKX) Service Repair Manual (GKX00001...fjkdksmmdm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components. Special tools are required.
3) It then lists 28 steps for reassembly, providing notes on cleaning, lubrication, and proper installation of O-rings and other parts to ensure correct assembly. The keys and notches must be properly aligned and torques applied to specifications.
Caterpillar Cat 330C L Excavator (Prefix DKY) Service Repair Manual (DKY00001...fjkdksmmdm
- The document provides disassembly and assembly instructions for the travel motor of a 330C L excavator.
- It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, and bearing races.
- It then describes 28 steps for assembling the travel motor, providing notes on cleaning, applying sealant, and ensuring proper alignment of components like the cam plate and keys.
- Tools required include retaining ring pliers, a bearing puller, threaded rod, and eyebolt for installation and removal of components.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then describes 13 steps for assembly, including installing seals, bearings, springs, and securing the rotating assembly back into the housing. Special tools are listed and safety notices are provided throughout regarding handling pressurized components and ensuring cleanliness during reassembly.
Caterpillar Cat 330C L Excavator (Prefix CYA) Service Repair Manual (CYA00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on a 330C L excavator. The disassembly process involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and includes installing seals, bearings, and retaining rings in their proper positions. Cleanliness is important during assembly to prevent contamination.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...fjkdksmmdm
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with no control movement to further release pressure across systems.
The document aims to safely depressurize hydraulic lines and components before disconnection or removal during maintenance.
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It describes 28 steps to disassemble the motor by removing components like the head, port plate, bearings, brake piston, plates, and seals. It then describes 13 steps for assembling the motor, replacing all seals and installing components in reverse order of removal. Special tools are required and cleanliness is important when handling parts.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The travel motor disassembly procedure involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals.
2. Travel motor assembly requires installing components in reverse order, applying thread lock compound and oil, and torquing bolts to specified values.
3. Special tools are required to remove races, seals, and retainers, and care must be taken to avoid damaging parts and ensure proper alignment of keys and plates.
This document provides instructions for assembling a piston motor (hydraulic fan) with 20 steps. It involves installing various components like bearing cups, seals, pins, springs, pistons, and plates in the proper sequence and orientation. Safety notes are included to handle parts carefully and apply oil during assembly. The summary is complete in 3 sentences.
1) The document provides disassembly and assembly instructions for a travel motor on 330C and 330C L excavator models.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, bearings, and housing covers.
3) It then lists 28 steps for reassembling the travel motor, replacing all seals and applying lubricant before reinstalling the components in reverse order of disassembly. Proper cleanliness and torque specifications are emphasized.
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
3) It then lists 28 steps for reassembling the travel motor, placing components back in reverse order and noting alignment and torque specifications. Precise reassembly is emphasized for correct operation.
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components. Special tools are required.
3) It then lists 28 steps for reassembly, providing notes on cleaning, lubrication, and proper installation of O-rings and other parts to ensure correct assembly. The keys and notches must be properly aligned and torques applied to specifications.
1) The document provides disassembly and assembly instructions for the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 29 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts in the proper order and with specified torques.
This document provides instructions for servicing components of a Caterpillar 330D L excavator engine. It describes procedures for removing and installing the cylinder head, camshaft, lifter group, and associated parts. The steps include draining coolant, removing mounting hardware, lifting components with tools, applying lubricant, and torquing fasteners to specified values. Safety notices are provided to keep parts clean and prevent damage during removal and installation.
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, shafts, seals, and housings and attaching the assembly to the excavator frame using bolts.
3. Proper cleaning, lubrication, and heating of parts is emphasized to ensure correct assembly. Tools, torque specifications, and maintenance procedures are also outlined.
Caterpillar Cat 330C L Excavator (Prefix MCA) Service Repair Manual (MCA00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The disassembly process involves removing 28 different components in a specific sequence. The assembly process reverses the disassembly steps and includes applying thread lock compound and lubricating components before reassembly. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...fjkdksmmdm
This document provides instructions for disassembling and assembling a 330C excavator travel motor. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then describes 13 steps for assembly, including installing seals, bearings, springs, cam plate, and rotating assembly into the housing. Special tools are listed and safety notices are provided throughout regarding cleaning, pressurized air, and spring loading.
Caterpillar Cat 330C L Excavator (Prefix JNK) Service Repair Manual (JNK00001...fjkdksmmdm
The document provides instructions for assembling and installing a piston motor (hydraulic fan). It is a 3 page document that details 20 steps for assembly, including installing various components like bearings, seals, springs and retaining rings. It then provides 11 steps for installing the assembled piston motor and attaching hoses and guards. Proper cleaning and lubrication of parts is emphasized.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...fjkdksmmdm
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by listing the required tools. The instructions then state to clean all parts, set the number 1 piston to top center, and align the camshaft and idler gears. The camshaft is then lubricated and inserted into the cylinder block. The thrust plate and bolts are installed and tightened. Lifters are repositioned and the procedure ends by installing the front cover and rocker arm assembly.
Caterpillar Cat 330C L Excavator (Prefix JCD) Service Repair Manual (JCD00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavators. It outlines 28 steps for disassembly, removing components like the head, springs, brake piston, and bearings. It then outlines 13 steps for assembly, replacing seals and installing components in the reverse order of disassembly, taking care to mark parts and return them to their original positions. Special tools are listed that may be required for tasks like removing races and seals.
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and seals. It then describes 15 steps for reassembling the motor and installing components in the reverse order, making sure to clean parts and apply thread lock compound as needed. Tools required include retaining ring pliers, a bearing puller, an eyebolt, and an adapter.
Caterpillar Cat 330C L Excavator (Prefix GKX) Service Repair Manual (GKX00001...fjkdksmmdm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components. Special tools are required.
3) It then lists 28 steps for reassembly, providing notes on cleaning, lubrication, and proper installation of O-rings and other parts to ensure correct assembly. The keys and notches must be properly aligned and torques applied to specifications.
Caterpillar Cat 330C L Excavator (Prefix DKY) Service Repair Manual (DKY00001...fjkdksmmdm
- The document provides disassembly and assembly instructions for the travel motor of a 330C L excavator.
- It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, and bearing races.
- It then describes 28 steps for assembling the travel motor, providing notes on cleaning, applying sealant, and ensuring proper alignment of components like the cam plate and keys.
- Tools required include retaining ring pliers, a bearing puller, threaded rod, and eyebolt for installation and removal of components.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then describes 13 steps for assembly, including installing seals, bearings, springs, and securing the rotating assembly back into the housing. Special tools are listed and safety notices are provided throughout regarding handling pressurized components and ensuring cleanliness during reassembly.
Caterpillar Cat 330C L Excavator (Prefix CYA) Service Repair Manual (CYA00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on a 330C L excavator. The disassembly process involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and includes installing seals, bearings, and retaining rings in their proper positions. Cleanliness is important during assembly to prevent contamination.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...fjkdksmmdm
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with no control movement to further release pressure across systems.
The document aims to safely depressurize hydraulic lines and components before disconnection or removal during maintenance.
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It describes 28 steps to disassemble the motor by removing components like the head, port plate, bearings, brake piston, plates, and seals. It then describes 13 steps for assembling the motor, replacing all seals and installing components in reverse order of removal. Special tools are required and cleanliness is important when handling parts.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The travel motor disassembly procedure involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals.
2. Travel motor assembly requires installing components in reverse order, applying thread lock compound and oil, and torquing bolts to specified values.
3. Special tools are required to remove races, seals, and retainers, and care must be taken to avoid damaging parts and ensure proper alignment of keys and plates.
This document provides instructions for assembling a piston motor (hydraulic fan) with 20 steps. It involves installing various components like bearing cups, seals, pins, springs, pistons, and plates in the proper sequence and orientation. Safety notes are included to handle parts carefully and apply oil during assembly. The summary is complete in 3 sentences.
1) The document provides disassembly and assembly instructions for a travel motor on 330C and 330C L excavator models.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, bearings, and housing covers.
3) It then lists 28 steps for reassembling the travel motor, replacing all seals and applying lubricant before reinstalling the components in reverse order of disassembly. Proper cleanliness and torque specifications are emphasized.
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
3) It then lists 28 steps for reassembling the travel motor, placing components back in reverse order and noting alignment and torque specifications. Precise reassembly is emphasized for correct operation.
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components. Special tools are required.
3) It then lists 28 steps for reassembly, providing notes on cleaning, lubrication, and proper installation of O-rings and other parts to ensure correct assembly. The keys and notches must be properly aligned and torques applied to specifications.
1) The document provides disassembly and assembly instructions for the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 29 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts in the proper order and with specified torques.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01414226
Inlet Manifold - Install
SMCS - 1058-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00675794
1. Install a new gasket (6) on the cylinder head.
Illustration 2 g00629952
2. Position the air inlet manifold (5) on the engine.
3. Install bolts (4). Tighten the bolts to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
4. Install air inlet elbows (2) on air inlet manifold (5).
5. Install bolts (1) and connect air inlet heater solenoid (3).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 13:17:22 UTC+0800 2020
2/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01943334
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
1/5
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g01011225
Note: The following components of the exhaust valves are different from the components of
the inlet valves: spring retainer (2), valve spring (3) and valve (5).
Illustration 2 g01011269
1. Use Tooling (A) to compress valve spring (3). Remove retainer lock (1).
2. Remove Tooling (A).
3. Remove spring retainer (2). Remove valve spring (3).
2/5
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 4. Remove valve seal (4) and valve (5).
5. Repeat Steps 1 through 4 in order to remove the remaining inlet valves and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
3/5
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 3 g01011225
1. Lubricate valve (5) with clean engine oil. Install valve (5) in the cylinder head assembly.
Install new valve seal (4) against the valve guide.
2. Place the following items on the valve stem: valve spring (3) and spring retainer (2).
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
Note: A small amount of grease can be used to hold retainer locks (1) in position during
installation.
4/5
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 4 g01011269
3. Use Tooling (A) to compress valve spring (3). Install retainer lock (1).
4. Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves.
End By:
a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 13:18:18 UTC+0800 2020
5/5
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01961680
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Asseblies 3114, 3116, and
3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162, "Procedure
to Measure and Salvage Cylinder Head Assemblies and Related Components".
1/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g00745735
Typical example
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (A) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
B 1U-7792 Guide Collar (1)
1
C 9U-6895 Valve Guide Driver 1
D 149-4008 Guide Collar 1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 2 g00745782
Typical example
1. Position inlet valve guide (1) and tap on the top of inlet valve guide (1). This is done in
order to start inlet valve guide (1) into the cylinder head assembly.
2. Use Tooling (A) and Tooling (B) to install inlet valve guide (1). Install inlet valve guides
(1) until tooling (B) contacts the cylinder head.
3/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00745672
Typical example
3. Position exhaust valve guide (2) and tap on the top of exhaust valve guide (2). This is done
in order to start the exhaust valve guide into the cylinder head assembly.
Note: Some of the early engines have inlet valves and exhaust valves that are identical in
size. Use the same specifications and the same tools for both valves. Proceed to Step 4 if the
valves are not the same size.
4. Use Tooling (C) and Tooling (D) to install exhaust valve guide (2). Install inlet valve guides
(2) until tooling (D) contacts the cylinder head.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 13:19:14 UTC+0800 2020
4/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929146
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor 1
B(1)
165-5647 Valve Seat Extractor 1
C(1)
6V-4804 Handle 1
D(1)
6V-4192 Threaded Shaft 1
E(1)
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
Illustration 1 g00615519
Illustration 2 g00656459
Note: Replace Tooling (A) with Tooling (B) for the removal of the inlet valve seat insert.
1. Install Tooling (A) in the exhaust valve seat insert.
2. Install Tooling (C) and Tooling (D) in Tooling (A). Hand tighten Tooling (D). Tooling (A)
will expand below the edge of valve seat insert (1).
2/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 3 g00656462
3. Install Tooling (E) on the cylinder head under Tooling (C). Hold Tooling (D) while you turn
Tooling (C). Remove valve seat insert (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
F 1U-6685 Guide and Insert Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
1. Cool the valve seat inserts for easier installation.
3/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g01003799
2. Turn Tooling (F) upside-down and use Tooling (F) and a press to install the valve seat
inserts in the cylinder head assembly.
3. After the valve seat inserts are installed, grind the inserts to the final specification. Refer to
Guideline for Reusable Parts and Salvage Operation, SEBF8218, "Specifications for
Cylinder Head Assemblies 3114, 3116, and 3126 Engines" for the specifications.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 13:20:10 UTC+0800 2020
4/4
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929163
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
Start By:
a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01009468
1. Use Tooling (A) to remove engine oil filter (3).
2. Disconnect the tube assembly for the turbocharger inlet (1) from the engine oil filter base
(4).
3. Remove bolts (2) and the washers that hold engine oil filter base (4) to the cylinder block.
4. Remove engine oil filter base (4) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 13:21:05 UTC+0800 2020
2/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929612
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Illustration 1 g01011623
Personal injury can result from being struck by parts propelled by a
released spring force.
1/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plugs (1) and (3) from oil filter base (2).
Illustration 2 g01011627
2. Remove springs (4) and valves (6). Remove O-ring seals (5) from plugs (1) and (3). Inspect
the parts for wear or damage. If the parts are worn or damaged, use new parts for
replacement.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 13:22:01 UTC+0800 2020
2/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929615
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
Illustration 1 g01011627
1. Install O-ring seals (5) onto plugs (1) and (3). Install valves (6) and springs (4).
1/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Illustration 2 g01011623
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install plugs (1) and (3) onto oil filter base (2).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jul 30 13:22:57 UTC+0800 2020
2/2
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02376426
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01009468
1/3
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 2 g01185803
Illustration 3 g00676791
1. Position the gasket and engine oil filter base (4) on the cylinder block.
2. Install the washers and bolts (2) that hold engine oil filter base (4) to the cylinder block.
Tighten the bolts according to the following procedure:
a. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 15 N·m (11
lb ft).
b. Tighten Bolt (1) through Bolt (15) in a numerical sequence to a torque of 28 N·m (21
lb ft).
3. Apply lubricant to new O-ring seal (5) . Install O-ring seal (5) in the fitting on the engine oil
filter base.
4. Connect tube assembly (1) to engine oil filter base (4) .
Note: Never install an oil filter with a wrench. Follow the instructions on the oil filter.
2/3
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED B...
2020/7/30
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...