This document provides instructions for removing and installing components on a Caterpillar 3126B engine, including:
- Procedures for removing and installing the camshaft, camshaft gear, camshaft bearings, and engine oil pan.
- Important safety notices about containing fluids, keeping parts clean, and disposing of fluids properly.
- Lists of required tools for each job, such as a camshaft bearing tool group.
- Step-by-step instructions for each removal and installation, including aligning timing marks and orienting oil holes.
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...fjkskedmme
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Caterpillar cat 325 c excavator (prefix crb) service repair manual (crb00001 ...fjsjjekdkme
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
Caterpillar cat 325 c l excavator (prefix bfe) service repair manual (bfe0000...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C L Excavator powered by a 3126B engine, including:
- Camshaft removal and installation, requiring alignment of timing marks.
- Camshaft gear removal and installation, using a press and heating the gear.
- Camshaft bearing removal and installation, noting oil hole orientation.
- Engine oil pan removal and installation, after draining oil into an appropriate container.
Safety precautions are outlined, such as containing fluids and cleaning parts to prevent damage or rapid wear. Special tools required are also listed.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
Daewoo doosan dl420 wheel loader operator and maintenance manualfjskkksmemm
This document is an operation and maintenance manual for a Doosan DL420 wheel loader. It provides information on the intended use of the machine, its components like the engine, transmission, braking and hydraulic systems. It also describes the cabin, FOPS and ROPS safety structures. The manual discusses CE marking requirements and installing communication equipment safely. Product plates for identifying the machine and components are shown.
Caterpillar cat 428 d backhoe loader (prefix bxc) service repair manual (bxc0...ujdfjkkskmem
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifters
- Camshaft and camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep components clean and properly support parts.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...fjkskedmme
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Caterpillar cat 325 c excavator (prefix crb) service repair manual (crb00001 ...fjsjjekdkme
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Install the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft gear
Caterpillar cat 325 c l excavator (prefix bfe) service repair manual (bfe0000...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C L Excavator powered by a 3126B engine, including:
- Camshaft removal and installation, requiring alignment of timing marks.
- Camshaft gear removal and installation, using a press and heating the gear.
- Camshaft bearing removal and installation, noting oil hole orientation.
- Engine oil pan removal and installation, after draining oil into an appropriate container.
Safety precautions are outlined, such as containing fluids and cleaning parts to prevent damage or rapid wear. Special tools required are also listed.
Caterpillar cat 312 c l excavator (prefix dbn) service repair manual (dbn0000...fksjksmmde
The document provides instructions for removing and installing a fuel injection pump on a Caterpillar 3064 engine. It describes:
1) Removing the fuel lines, access cover, and mounting bolts to detach the pump.
2) Installing a new gasket and securing bolts to reattach the pump, ensuring proper alignment.
3) Reconnecting the fuel lines once the pump is secured.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
Daewoo doosan dl420 wheel loader operator and maintenance manualfjskkksmemm
This document is an operation and maintenance manual for a Doosan DL420 wheel loader. It provides information on the intended use of the machine, its components like the engine, transmission, braking and hydraulic systems. It also describes the cabin, FOPS and ROPS safety structures. The manual discusses CE marking requirements and installing communication equipment safely. Product plates for identifying the machine and components are shown.
Caterpillar cat 428 d backhoe loader (prefix bxc) service repair manual (bxc0...ujdfjkkskmem
This document provides instructions for removing and installing various engine components on a Caterpillar 3054C engine, including:
- Lifters
- Camshaft and camshaft bearings
- Engine oil pan
- Piston cooling jets
The instructions include lists of required tools, step-by-step procedures, torque specifications, and cautions to keep components clean and properly support parts.
Caterpillar cat 321 b lcr track excavator (prefix 2zd) service repair manual ...fujsfskekem
This document provides instructions for removing and installing various fuel system components on a Caterpillar 321B LCR Track Excavator engine, including:
- Fuel priming pump
- Fuel filter base
- Fuel injection lines
It describes removing nuts, bolts, lines, and filters, taking care to plug openings to prevent contamination. Reinstallation involves cleaning parts and reconnecting components with new washers or O-rings as needed, torquing to specifications.
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...fjskeazqkkdmme
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Caterpillar cat 325 c excavator (prefix amh) service repair manual (amh00001 ...ifosodkmsme
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Procedures for removing the camshaft, camshaft gear, camshaft bearings, and engine oil pan. Safety notices and required tools are listed.
2. Instructions for installing the camshaft, camshaft gear, camshaft bearings, and engine oil pan. Diagrams illustrate the component locations and installation steps. Torque specifications and seals/gaskets are addressed.
3. Component removal and installation is described in step-by-step format with references to other relevant sections for some components. Proper cleaning, handling and disposal of fluids
Caterpillar cat 325 c excavator (prefix amh) service repair manual (amh00001 ...fjskekdmjekm
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
This document provides instructions for removing and installing the engine oil pan on a Caterpillar 3126B engine. The removal procedure involves draining the oil, removing bolts, and lifting off the pan. The installation procedure specifies cleaning the pan and mating surfaces, applying sealant, installing bolts, and checking the seal. Tools and safety precautions are also outlined.
Caterpillar Cat 325C L Excavator (Prefix AMH) Service Repair Manual (AMH00001...shudun96087
The document provides instructions for removing and installing the camshaft, camshaft gear, camshaft bearings, and engine oil pan on a 325C excavator with a 3126B engine. The procedures describe draining fluids, using proper tools, cleaning parts, and ensuring proper alignment of components during installation for correct timing. Safety notices are provided regarding containing fluids and preventing contamination.
Caterpillar Cat 325C L Excavator (Prefix AMH) Service Repair Manual (AMH00001...yfbr995309
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine. It describes removing the lifter group and front cover, turning the crankshaft to top dead center, and wiring the valve lifters away from the camshaft. It then details removing the camshaft retainer plate and bolts and removing the camshaft from the cylinder block. Reinstallation is described as well.
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine. It describes removing the lifter group and front cover, turning the crankshaft to top dead center, and wiring the valve lifters away from the camshaft. It then details removing the camshaft retainer plate and bolts and removing the camshaft from the cylinder block. Reinstallation is described as well.
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine. It describes removing the lifter group and front cover, turning the crankshaft to top dead center, and wiring the valve lifters away from the camshaft. It then details removing the camshaft retainer plate and bolts and removing the camshaft from the cylinder block. Reinstallation is described as well.
Caterpillar Cat 325C L Excavator (Prefix AMH) Service Repair Manual (AMH00001...kesi7153062
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine. It describes removing the lifter group and front cover, turning the crankshaft to top dead center, and wiring the valve lifters away from the camshaft. It then details removing the camshaft retainer plate and bolts and removing the camshaft from the cylinder block. Reinstallation is described as well.
Caterpillar cat 325 c ln excavator (prefix crb) service repair manual (crb000...fjsjjekdkme
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Reinstall the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft
Caterpillar cat 325 c l excavator (prefix crb) service repair manual (crb0000...fjsjjekdkme
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. It describes removing the lifter group and front cover, turning the crankshaft to top dead center, and removing the camshaft retainer plate and camshaft. Reinstallation involves cleaning parts, installing the camshaft and ensuring proper timing marks are aligned, and replacing the retainer plate and covers.
Caterpillar cat 325 c l excavator (prefix bfe) service repair manual (bfe0000...fhsejkdkmen
The document provides instructions for servicing components of a Caterpillar 3126B diesel engine, including removing and installing the camshaft, camshaft gear, camshaft bearings, and engine oil pan. The procedures describe draining fluids, removing parts, cleaning surfaces, applying sealant, installing new gaskets, and tightening fasteners to specified torques. Tools required are also listed. Safety notices warn of hot oil and containing fluids during disassembly and repair.
Caterpillar cat 325 c excavator (prefix bfe) service repair manual (bfe00001 ...fjjskejdmdn
This document provides instructions for removing and installing various engine components on a 325C and 325C L Excavator, including:
1. Instructions for removing the camshaft, including ensuring proper timing marks are aligned.
2. Instructions for installing the camshaft, making sure number one cylinder is at top center and timing marks are aligned.
3. Instructions for removing the camshaft gear by first removing the camshaft, and then pressing the camshaft from the gear.
4. Instructions for installing the camshaft gear by aligning the key and pressing the gear onto the camshaft.
Caterpillar cat 325 c excavator (prefix bfe) service repair manual (bfe00001 ...fjskekdmjekm
This document provides instructions for removing and installing various engine components on a Caterpillar 325C L Excavator powered by a 3126B engine, including:
- Camshaft removal and installation, requiring alignment of timing marks.
- Camshaft gear removal and installation, using a press and heating the gear.
- Camshaft bearing removal and installation, noting oil hole orientation.
- Engine oil pan removal and installation, after draining oil into an appropriate container.
Safety precautions are outlined, such as containing fluids and cleaning parts to prevent damage or rapid wear. Special tools required are also listed.
Caterpillar cat 325 c excavator (prefix bfe) service repair manual (bfe00001 ...ifosodkmsme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator including:
1. The camshaft, camshaft bearings, camshaft gear, engine oil pan, and piston cooling jets. Detailed steps are given for each procedure, including necessary tools and safety precautions.
2. Camshaft removal requires removing the lifter group and front cover first. Camshaft bearings are removed one at a time using a special tool to maintain proper orientation.
3. Engine oil pan removal requires draining the oil first before removing bolts and gasket. Cleaning and applying sealant is important for installation.
Massey ferguson mf 788 combine parts catalogue manualfjjskejdmdn
This document contains parts listings and descriptions for a Massey Ferguson MF 788 combine diesel engine. It includes sections for the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction system, timing gear, lubricating oil sump, lubricating oil filter, and other engine parts. The listings provide part numbers, quantities, descriptions, and assembly/component details for each part.
Massey ferguson mf 625 combines parts catalogue manualfjjskejdmdn
This document contains parts lists and technical specifications for Massey Ferguson MF 620/625 combines. It includes lists of parts, part numbers, quantities and descriptions for the cylinder block, cylinder head, crankshaft, and cylinder head cover. Each part is accompanied by additional details like serial number ranges and replacement part numbers.
Massey ferguson mf 620 combines parts catalogue manualfjjskejdmdn
This document contains parts lists and technical specifications for Massey Ferguson MF 620/625 combines. It includes lists of parts, part numbers, quantities and descriptions for the cylinder block, cylinder head, crankshaft, and cylinder head cover. Notes are provided on application and replacement of certain parts based on the combine's serial number or engine number.
Massey ferguson mf 515 combines (gb) parts catalogue manualfjjskejdmdn
The document provides parts listings and technical specifications for components of Massey Ferguson 510/515 combines. It includes lists of parts, part numbers, quantities and other identifying information for the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction system, and timing gear of MF 510/515 combines. Notes are provided to indicate application details for some parts.
Massey ferguson mf 510 combines (gb) parts catalogue manualfjjskejdmdn
This document provides parts information for a Massey Ferguson MF 510/515 combine, including the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction system, and timing gear. It lists over 100 individual part numbers, quantities, descriptions, and other identifying information organized into sections for each component or assembly.
Massey ferguson mf 500 combine (gb) parts catalogue manualfjjskejdmdn
This document provides parts information for the cylinder block, cylinder head, crankshaft, and cylinder head cover of a Massey Ferguson MF 500 combine. It includes lists of parts with part numbers, quantities, descriptions, and notes on application and serial number ranges. Key assemblies like the cylinder block, head, crankshaft, and head cover can be ordered, and individual parts like pistons, rods, bearings, gaskets, and seals are also listed. Notes provide additional details on part application and changes over different serial number ranges.
Massey ferguson mf 430 combine parts catalogue manualfjjskejdmdn
This document provides a parts list for a Massey Ferguson 430 combine. It includes 3 tables of contents that list various systems of the combine including the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction and exhaust system, timing gear, and lubricating oil sump. Each system lists the relevant parts, part numbers, quantities, and additional part details.
More Related Content
Similar to Caterpillar cat 325 c excavator (prefix amh) service repair manual (amh00001 and up)
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...fjskeazqkkdmme
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Caterpillar cat 325 c excavator (prefix amh) service repair manual (amh00001 ...ifosodkmsme
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Procedures for removing the camshaft, camshaft gear, camshaft bearings, and engine oil pan. Safety notices and required tools are listed.
2. Instructions for installing the camshaft, camshaft gear, camshaft bearings, and engine oil pan. Diagrams illustrate the component locations and installation steps. Torque specifications and seals/gaskets are addressed.
3. Component removal and installation is described in step-by-step format with references to other relevant sections for some components. Proper cleaning, handling and disposal of fluids
Caterpillar cat 325 c excavator (prefix amh) service repair manual (amh00001 ...fjskekdmjekm
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
This document provides instructions for removing and installing the engine oil pan on a Caterpillar 3126B engine. The removal procedure involves draining the oil, removing bolts, and lifting off the pan. The installation procedure specifies cleaning the pan and mating surfaces, applying sealant, installing bolts, and checking the seal. Tools and safety precautions are also outlined.
Caterpillar Cat 325C L Excavator (Prefix AMH) Service Repair Manual (AMH00001...shudun96087
The document provides instructions for removing and installing the camshaft, camshaft gear, camshaft bearings, and engine oil pan on a 325C excavator with a 3126B engine. The procedures describe draining fluids, using proper tools, cleaning parts, and ensuring proper alignment of components during installation for correct timing. Safety notices are provided regarding containing fluids and preventing contamination.
Caterpillar Cat 325C L Excavator (Prefix AMH) Service Repair Manual (AMH00001...yfbr995309
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine. It describes removing the lifter group and front cover, turning the crankshaft to top dead center, and wiring the valve lifters away from the camshaft. It then details removing the camshaft retainer plate and bolts and removing the camshaft from the cylinder block. Reinstallation is described as well.
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine. It describes removing the lifter group and front cover, turning the crankshaft to top dead center, and wiring the valve lifters away from the camshaft. It then details removing the camshaft retainer plate and bolts and removing the camshaft from the cylinder block. Reinstallation is described as well.
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine. It describes removing the lifter group and front cover, turning the crankshaft to top dead center, and wiring the valve lifters away from the camshaft. It then details removing the camshaft retainer plate and bolts and removing the camshaft from the cylinder block. Reinstallation is described as well.
Caterpillar Cat 325C L Excavator (Prefix AMH) Service Repair Manual (AMH00001...kesi7153062
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine. It describes removing the lifter group and front cover, turning the crankshaft to top dead center, and wiring the valve lifters away from the camshaft. It then details removing the camshaft retainer plate and bolts and removing the camshaft from the cylinder block. Reinstallation is described as well.
Caterpillar cat 325 c ln excavator (prefix crb) service repair manual (crb000...fjsjjekdkme
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. The summary is:
1) Remove the lifter group and front cover to access the camshaft. Wire the valve lifters away from the camshaft. Remove the camshaft retainer plate and bolts, then remove the camshaft.
2) Install the camshaft, ensuring the timing marks are aligned. Install the camshaft retainer plate and bolts. Reinstall the lifter group and front cover.
3) The document provides step-by-step instructions for removing and installing the camshaft, camshaft
Caterpillar cat 325 c l excavator (prefix crb) service repair manual (crb0000...fjsjjekdkme
The document provides instructions for removing and installing the camshaft on a Caterpillar 3126B engine used in 325C excavators. It describes removing the lifter group and front cover, turning the crankshaft to top dead center, and removing the camshaft retainer plate and camshaft. Reinstallation involves cleaning parts, installing the camshaft and ensuring proper timing marks are aligned, and replacing the retainer plate and covers.
Caterpillar cat 325 c l excavator (prefix bfe) service repair manual (bfe0000...fhsejkdkmen
The document provides instructions for servicing components of a Caterpillar 3126B diesel engine, including removing and installing the camshaft, camshaft gear, camshaft bearings, and engine oil pan. The procedures describe draining fluids, removing parts, cleaning surfaces, applying sealant, installing new gaskets, and tightening fasteners to specified torques. Tools required are also listed. Safety notices warn of hot oil and containing fluids during disassembly and repair.
Caterpillar cat 325 c excavator (prefix bfe) service repair manual (bfe00001 ...fjjskejdmdn
This document provides instructions for removing and installing various engine components on a 325C and 325C L Excavator, including:
1. Instructions for removing the camshaft, including ensuring proper timing marks are aligned.
2. Instructions for installing the camshaft, making sure number one cylinder is at top center and timing marks are aligned.
3. Instructions for removing the camshaft gear by first removing the camshaft, and then pressing the camshaft from the gear.
4. Instructions for installing the camshaft gear by aligning the key and pressing the gear onto the camshaft.
Caterpillar cat 325 c excavator (prefix bfe) service repair manual (bfe00001 ...fjskekdmjekm
This document provides instructions for removing and installing various engine components on a Caterpillar 325C L Excavator powered by a 3126B engine, including:
- Camshaft removal and installation, requiring alignment of timing marks.
- Camshaft gear removal and installation, using a press and heating the gear.
- Camshaft bearing removal and installation, noting oil hole orientation.
- Engine oil pan removal and installation, after draining oil into an appropriate container.
Safety precautions are outlined, such as containing fluids and cleaning parts to prevent damage or rapid wear. Special tools required are also listed.
Caterpillar cat 325 c excavator (prefix bfe) service repair manual (bfe00001 ...ifosodkmsme
This document provides instructions for removing and installing various engine components on a Caterpillar 325C excavator including:
1. The camshaft, camshaft bearings, camshaft gear, engine oil pan, and piston cooling jets. Detailed steps are given for each procedure, including necessary tools and safety precautions.
2. Camshaft removal requires removing the lifter group and front cover first. Camshaft bearings are removed one at a time using a special tool to maintain proper orientation.
3. Engine oil pan removal requires draining the oil first before removing bolts and gasket. Cleaning and applying sealant is important for installation.
Similar to Caterpillar cat 325 c excavator (prefix amh) service repair manual (amh00001 and up) (15)
Massey ferguson mf 788 combine parts catalogue manualfjjskejdmdn
This document contains parts listings and descriptions for a Massey Ferguson MF 788 combine diesel engine. It includes sections for the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction system, timing gear, lubricating oil sump, lubricating oil filter, and other engine parts. The listings provide part numbers, quantities, descriptions, and assembly/component details for each part.
Massey ferguson mf 625 combines parts catalogue manualfjjskejdmdn
This document contains parts lists and technical specifications for Massey Ferguson MF 620/625 combines. It includes lists of parts, part numbers, quantities and descriptions for the cylinder block, cylinder head, crankshaft, and cylinder head cover. Each part is accompanied by additional details like serial number ranges and replacement part numbers.
Massey ferguson mf 620 combines parts catalogue manualfjjskejdmdn
This document contains parts lists and technical specifications for Massey Ferguson MF 620/625 combines. It includes lists of parts, part numbers, quantities and descriptions for the cylinder block, cylinder head, crankshaft, and cylinder head cover. Notes are provided on application and replacement of certain parts based on the combine's serial number or engine number.
Massey ferguson mf 515 combines (gb) parts catalogue manualfjjskejdmdn
The document provides parts listings and technical specifications for components of Massey Ferguson 510/515 combines. It includes lists of parts, part numbers, quantities and other identifying information for the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction system, and timing gear of MF 510/515 combines. Notes are provided to indicate application details for some parts.
Massey ferguson mf 510 combines (gb) parts catalogue manualfjjskejdmdn
This document provides parts information for a Massey Ferguson MF 510/515 combine, including the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction system, and timing gear. It lists over 100 individual part numbers, quantities, descriptions, and other identifying information organized into sections for each component or assembly.
Massey ferguson mf 500 combine (gb) parts catalogue manualfjjskejdmdn
This document provides parts information for the cylinder block, cylinder head, crankshaft, and cylinder head cover of a Massey Ferguson MF 500 combine. It includes lists of parts with part numbers, quantities, descriptions, and notes on application and serial number ranges. Key assemblies like the cylinder block, head, crankshaft, and head cover can be ordered, and individual parts like pistons, rods, bearings, gaskets, and seals are also listed. Notes provide additional details on part application and changes over different serial number ranges.
Massey ferguson mf 430 combine parts catalogue manualfjjskejdmdn
This document provides a parts list for a Massey Ferguson 430 combine. It includes 3 tables of contents that list various systems of the combine including the cylinder block, cylinder head, crankshaft, cylinder head cover, air induction and exhaust system, timing gear, and lubricating oil sump. Each system lists the relevant parts, part numbers, quantities, and additional part details.
Massey ferguson mf 415 combines parts catalogue manualfjjskejdmdn
This document provides part numbers and descriptions for components of the lubricating oil sump for Massey Ferguson MF 410/415 combines. It includes over 80 numbered items that make up the sump assembly, such as the sump, gaskets, bolts, gears, strainers, pumps, pipes, unions and other components. Precise part numbers are given to allow for ordering replacements. Notes provide additional details for some parts, such as applicable serial number ranges.
Massey ferguson mf 410 combines parts catalogue manualfjjskejdmdn
This document provides part numbers and descriptions for components of the lubricating oil sump for Massey Ferguson MF 410/415 combines. It includes over 80 numbered items that make up the sump assembly, such as the sump, gaskets, bolts, gears, strainers, pumps, pipes, unions and other components. Precise part numbers are given to allow for ordering replacements. Notes provide additional details for some parts, such as applicable serial number ranges.
Massey ferguson mf 400 combine (gb) parts catalogue manualfjjskejdmdn
This document provides parts information for a Massey Ferguson MF 400 combine engine. It includes lists of parts for various engine systems like the cylinder block, crankshaft, cylinder head cover, and lubricating oil sump. Each part is identified by number, description, and any relevant comments on application or changes over time. The parts lists contain technical specifications to aid in maintenance and repair of the engine.
Massey ferguson mf 330 combine parts catalogue manualfjjskejdmdn
This document provides a parts list for the cylinder block of a Massey Ferguson MF 330 combine. It contains 46 numbered items including the cylinder block, liners, plugs, bolts, and other components. Each item lists the part number, quantity, description, and any relevant comments. Tolerances or fits are indicated with an "X" next to the part number.
Massey ferguson mf 290 tractor, 387020 (gb) parts catalogue manualfjjskejdmdn
The document contains detailed parts lists and diagrams for components of a Massey Ferguson MF 290 tractor engine. It lists 56 items that make up the timing gear assembly of an A4 248 engine, including the camshaft, gears, covers, joints, screws, washers, and other individual parts. Similar details are provided for other engine assemblies like the cylinder block, cylinder head, crankshaft, air induction/exhaust systems, and cylinder head cover. The document acts as a service or repair manual containing precise part numbers and descriptions for replacing or servicing parts of the MF 290 tractor engine.
Massey ferguson mf 265 tractor, 193552 (gb) parts catalogue manualfjjskejdmdn
The document contains parts lists and technical specifications for components of a Massey Ferguson MF 265 tractor engine. It lists over 30 individual components of the engine including the cylinder block, crankshaft, pistons, connecting rods, cylinder head, rocker shaft, timing gear and camshaft. Each component item is accompanied by part numbers, quantities, descriptions and any relevant comments. The level of technical detail provided suggests this is a service or repair document for mechanics working on this engine.
The document provides parts listings and descriptions for various components of a Massey Ferguson 240 tractor, including the engine, cylinder block, crankshaft, pistons, connecting rods, and cylinder head. It includes the part numbers, quantities, descriptions, and additional comments for over 50 individual parts.
Massey ferguson mf 240 tractor, 522353 (gb) parts catalogue manualfjjskejdmdn
The document appears to be parts lists and technical specifications for a Massey Ferguson MF 240 tractor. It includes lists of over 60 individual parts for components like the cylinder block, cylinder head, crankshaft, and timing gear. Each part is given an item number, part number, quantity, description, and sometimes additional comments or specifications.
Massey ferguson 1760 m compact tractor parts catalogue manualfjjskejdmdn
The document is a table of contents and service manual sections for a Massey Ferguson 1760M compact tractor. It includes sections on the engine and fuel systems, steering, drivetrain, brakes, hydraulics, electrical systems, cab, chassis, decals, wheels, implement lift system and accessories. Each section includes detailed part listings, diagrams and specifications for repairing and servicing the tractor systems.
Massey ferguson 1755 m compact tractor parts catalogue manualfjjskejdmdn
The document provides a table of contents and technical specifications for the Massey Ferguson 1755M compact tractor. It lists 12 systems of the tractor, including the engine and fuel system, steering system, drive train system, and more. Each system section includes detailed part listings, diagrams, and specifications for repair and maintenance of the tractor.
Claas temis 650 z (type t05) tractor service repair manualfjjskejdmdn
This document provides instructions for removing and installing gearbox casings and components for three types of TEMIS gearboxes. It describes:
1) Removing and installing input housing covers, main gearbox covers, and the top cover.
2) Adjusting the gear and range control levers during top cover installation.
3) Key components of the selecter rails and forks such as the forks, liners, and locking pins.
4) The gear and range controls for each gearbox type, which include mechanical levers and electro-hydraulic controls.
Claas temis 650 x (type t05) tractor service repair manualfjjskejdmdn
This document provides instructions for removing and installing various components of three different gearbox models: B13.25, B13.29, and B13.35. It describes the controls for each gearbox and provides an exploded view diagram and key. The main steps outlined are:
1. Remove the input housing and disconnect the rear axle from the main gearbox.
2. Remove the main gearbox top cover to access the selector rails and forks.
3. Mark selector positions and loosen locking bolts and wires on forks and selectors.
4. Disconnect switches and extract push buttons and balls to remove selector rails.
Claas temis 650 rx (type t05) tractor service repair manualfjjskejdmdn
This document provides instructions for removing and installing gearbox casings and components for three types of TEMIS gearboxes. It describes:
1) Removing and installing input housing covers, main gearbox covers, and the top cover.
2) Adjusting the gear and range control levers during top cover installation.
3) Key components of the selecter rails and forks such as the forks, liners, and locking pins.
4) The gear and range controls for each gearbox type, which include mechanical levers and electro-hydraulic controls.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR AMH
Configuration: 325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01196838
Camshaft - Remove
SMCS - 1210-011
Removal Procedure
Start By:
a. Remove the lifter group. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
b. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/3
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Dispose of all fluids according to local regulations and mandates.
1. Turn the crankshaft to top center compression stroke for the No. 1 piston. Install the timing
bolt in the flywheel. This is for timing during installation.
2. Ensure that the timing marks on the following gears are aligned: the camshaft drive gear, the
idler gear and the crankshaft gear.
Note: It is not necessary to remove the cylinder head for removal of the camshaft.
3. Wire the valve lifters away from the camshaft.
Illustration 1 g00640035
4. Remove two bolts (3) and camshaft retainer plate (2) from camshaft gear (1).
Illustration 2 g00640030
5. Remove camshaft (4) from the cylinder block.
2/3
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR AMH
Configuration: 325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01196611
Camshaft - Install
SMCS - 1210-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00640030
1. Carefully install camshaft (4) in the engine.
NOTICE
1/2
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. When installing the camshaft, make sure the number one cylinder is at
top center of the compression stroke with the timing bolt installed in
the flywheel. The camshaft timing is very important. The timing mark
on the camshaft drive gear must line up with the timing mark on the
idler gear. Refer to the Specifications Manual for more information.
2. Ensure that the timing marks on the following gears are aligned: the camshaft drive gear, the
idler gear and the crankshaft gear.
Illustration 2 g00640035
3. Install camshaft retainer plate (2) and two bolts (3) on camshaft gear (1).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
b. Install the lifter group. Refer to Disassembly and Assembly, "Lifter Group - Remove and
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 12:34:23 UTC+0800 2020
2/2
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR AMH
Configuration: 325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01983227
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
1. Wrap the camshaft with a protective covering in order to prevent damage to the camshaft.
Illustration 1 g00987675
NOTICE
1/2
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Do not allow the camshaft to fall to the floor when pressing it from the
drive gear. Also make sure that the camshaft lobes do not catch on the
press plates.
2. Place camshaft (2) and camshaft gear (1) in a suitable press. Press camshaft (2) from
camshaft gear (1).
3. If necessary, remove the key (3) from the camshaft.
Installation Procedure
Illustration 2 g00987675
1. Raise the temperature of camshaft gear (1).
2. Align key (3) in the camshaft with the groove (keyway) in the camshaft gear.
3. Install camshaft gear (1) on the end of camshaft (2).
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 12:35:19 UTC+0800 2020
2/2
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR AMH
Configuration: 325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02183087
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
Start By:
a. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Note the oil hole orientation in each camshaft bearing prior to removal for assembly
purposes.
1. Use Tooling (A) to remove the camshaft bearings from the cylinder block.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-2241 Camshaft Bearing Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g01104577
3/4
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 2 g01104579
1. Use Tooling (A) to install all of the camshaft bearings except for the front bearing. Orient
oil hole (1) in each bearing so that oil hole (1) is located at the top of the bore.
2. Use Tooling (A) to install the front camshaft bearing. Align oil hole (1) in the front
camshaft bearing with the oil hole in the cylinder block. Locate joint (2) in the front
camshaft bearing in the proper position.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 12:36:15 UTC+0800 2020
4/4
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR AMH
Configuration: 325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02173704
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
Hot oil and components can cause personal injury.
Do not allow hot oil or components to contact skin.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/5
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the engine oil into a suitable container for storage or disposal.
Illustration 1 g00610543
Typical example
Note: Do not pry or gouge the sealing surface of the engine oil pan. Use a rubber mallet to
tap lightly on the engine oil pan, if it is necessary.
2. Remove the bolts for engine oil pan (1). Remove engine oil pan (1) .
Illustration 2 g00610550
Typical example
2/5
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 3. Remove gasket (2) from engine oil pan (1) .
4. Remove the drain plug and the O-ring seal from engine oil pan (1) .
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-9612 Silicone Sealant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Install the drain plug and the O-ring seal on the engine oil pan. Tighten the drain plug to 25
± 5 N·m (18 ± 4 lb ft).
2. Inspect the condition of the gasket. Replace the gasket, if necessary.
Note: On newer engines, the oil pan has an integral seal. Inspect the condition of the seal
and replace the seal, if necessary.
Illustration 3 g01010643
3/5
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 3. Clean the mating surface of the engine oil pan and the cylinder block.
4. Apply Tooling (A) to the T-shaped gasket joints of the oil pan. Refer to Illustration 3.
Illustration 4 g00610550
Typical example
Illustration 5 g00610543
Typical example
5. Position new gasket (2) and engine oil pan (1) on the cylinder block.
4/5
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 6 g00610574
6. Install the bolts for the engine oil pan. Tighten Bolts (X) to a torque of 31 ± 3 N·m (23 ± 2
lb ft).
7. Start at Bolt (Z) and tighten the remaining bolts in a counterclockwise direction. Tighten the
remaining bolts to a torque of 31 ± 3 N·m (23 ± 2 lb ft).
8. Start at Bolt (Z) and tighten the bolts again in a counterclockwise direction. Tighten the
bolts to a torque of 31 ± 3 N·m (23 ± 2 lb ft).
9. Fill the engine with oil to the correct level. Refer to the Operation and Maintenance Manual
for the correct filling procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 12:37:11 UTC+0800 2020
5/5
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR AMH
Configuration: 325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02372739
Piston Cooling Jets - Remove and Install
SMCS - 1331-010
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g00987444
1. Remove bolt (2) and piston cooling jet (1) from each cylinder.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 2 g00987444
1. Position piston cooling jet (1) in the cylinder block. Install bolt (2). Tighten the bolt to a
torque of 28 ± 7 N·m (21 ± 5 lb ft).
End By:
a. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 12:38:06 UTC+0800 2020
3/3
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR AMH
Configuration: 325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02180392
Pistons and Connecting Rods - Remove
SMCS - 1225-011
Removal Procedure
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
b. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
c. Remove the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
The joint between the connecting rod and the connecting rod cap is
produced by fracturing. The connecting rod assembly must be handled
with care in order to avoid damage to the mating surfaces. The
connecting rod assembly must be replaced if any damage occurs to the
mating surfaces. New connecting rod assemblies come with the
connecting rod caps bolted on the connecting rod.
1/2
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Use only a soft jawed vise to hold the connecting rod assembly when
removing the connecting rod cap bolts. Use only a soft faced hammer
to tap the connecting rod cap when separating the connecting rod cap
from the connecting rod.
Failure to use a soft jawed vise and a soft faced hammer may result in
damage to the connecting rod assembly.
1. Turn the crankshaft until the connecting rod caps are at the bottom center.
Illustration 1 g01062853
2. Inspect connecting rod (1) and connecting rod cap (3) for the proper identification mark.
The connecting rod and the connecting rod cap should have an etched number on the side
that is toward the right side of the engine. The number should match the cylinder number.
Mark the connecting rod and the connecting rod cap, if necessary. Do not etch new
markings on connecting rod or rod cap.
3. Remove connecting rod bolts (2) and connecting rod cap (3).
4. Remove the lower half of connecting rod bearing (5) from connecting rod cap (3).
5. Push the piston and the connecting rod away from the crankshaft. Remove the upper half of
connecting rod bearing (4) from connecting rod (1).
6. Remove the piston and connecting rod (1) from the cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 12:39:02 UTC+0800 2020
2/2
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR AMH
Configuration: 325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01983492
Pistons and Connecting Rods - Disassemble
SMCS - 1225-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6683 Ring Expander 1
B 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the pistons and the connecting rods. Refer to Disassembly and Assembly, "Pistons
and Connecting Rods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g00988677
1. Use Tooling (B) to remove retaining ring (2). Remove piston pin (4) and separate piston (1)
from connecting rod (3).
2/3
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 2 g00988681
2. Use Tooling (A) to remove piston rings (5).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 12:39:58 UTC+0800 2020
3/3
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325C EXCAVATOR AMH
Configuration: 325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01983502
Pistons and Connecting Rods - Assemble
SMCS - 1225-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6683 Ring Expander 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Verify correct assembly of the pistons and the connecting rods. Ensure
that the etched numbers on the rod and the rod cap are in the correct
positions. The etched number on the rod and the rod cap correspond to
the cylinder in which it should be installed.
1/4
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Illustration 1 g00988681
1. Check the clearance between the ends of piston rings (5). Refer to the Specifications
Manual, "Pistons and Rings".
Note: The oil ring must be installed over the spring with the end gap 180 degrees from the
oil ring spring joint.
2. Install the oil control piston ring with Tooling (A). The ends of the spring should be rotated
180 degrees from the ring end gap.
3. Install the intermediate piston ring with the side marked "UP-2" toward the top of the
piston. Use Tooling (A) in order to install the intermediate piston ring.
4. Install the top piston ring with the side marked "UP-1" toward the top of the piston. Use
Tooling (A) in order to install the top piston ring.
2/4
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 2 g00988732
5. Replace rod bearing (6) by pressing a new bearing into the connecting rod. Refer to Special
Instruction, SEHS7295 for the correct tooling and the correct installation procedure.
Illustration 3 g01027812
3/4
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. 6. The piston is a two-piece assembly. This piston consists of piston crown (7) and piston skirt
(8). Bearing (9) is nonserviceable.
Illustration 4 g00988677
NOTICE
An improperly installed retainer ring could cause the piston and
connecting rod to come apart during engine operation. This action can
result in a broken Piston Skirt and major engine damage.
7. Position piston (1) on connecting rod (3). Coat pin (4) with clean engine oil and install pin
(4). Ensure that the retainer rings are in the grooves of piston (1).
End By:
a. Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Pistons
and Connecting Rods - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed May 13 12:40:54 UTC+0800 2020
4/4
325C & 325C L Excavators AMH00001-UP (MACHINE) POWERED BY 3126B En...
2020/5/13
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...