This service repair manual provides instructions for removing and installing inlet manifolds, valves, and valve guides on Caterpillar 325B and 325B LN excavator engines. The document outlines the required tools and safety procedures, and provides step-by-step instructions with illustrations for each repair procedure. Technicians are advised to keep parts clean, contain fluids properly, and refer to other documents for guidance on reusable components.
Caterpillar cat 325 b excavator (prefix 6dn) service repair manual (6dn00001 ...fjsjjekdkme
This service repair manual provides instructions for removing and installing inlet manifolds, valves, and valve guides on Caterpillar 325B and 325B LN excavator engines. The document outlines the required tools and safety procedures, and provides step-by-step instructions with illustrations for each repair procedure. Technicians are advised to keep parts clean, contain fluids properly, and refer to other documents for guidance on reusable components.
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
The document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325-A excavator. It lists the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and installing new inserts. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...fjsjjekdkme
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 track type excavator (prefix 7 cj) service repair manual ...jdfjskekmdme
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 track type excavator (prefix 7 cj) service repair manual ...cdfzxs
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 l track type excavator (prefix 7cj) service repair manual...jdfjskekmdme
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 b excavator (prefix 6dn) service repair manual (6dn00001 ...fjsjjekdkme
This service repair manual provides instructions for removing and installing inlet manifolds, valves, and valve guides on Caterpillar 325B and 325B LN excavator engines. The document outlines the required tools and safety procedures, and provides step-by-step instructions with illustrations for each repair procedure. Technicians are advised to keep parts clean, contain fluids properly, and refer to other documents for guidance on reusable components.
1. The document provides instructions for removing and installing inlet and exhaust valve seat inserts from an excavator engine.
2. It describes the required tools and gives illustrated step-by-step instructions for removing inserts using a valve seat extractor tool and installing new inserts.
3. Technicians are advised to keep parts clean and refer to other documents for specifications on reusable parts.
The document provides instructions for removing and installing inlet and exhaust valve seat inserts on a 325-A excavator. It lists the required tools and gives a step-by-step process that includes using a valve seat extractor tool to remove the inserts from the cylinder head and installing new inserts. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
Caterpillar cat 325 b excavator (prefix 8fn) service repair manual (8fn00001 ...fjsjjekdkme
This document provides instructions for removing and installing a cylinder head on an excavator. It begins by listing other components that must first be removed, such as the fuel filter base, governor, fuel linkage, and manifolds. The removal procedure then instructs technicians to attach a lifting device to the cylinder head and remove bolts holding it to the cylinder block before removing the gasket. The installation procedure lists cleaning the mating surfaces and applying lubricant to the gasket before positioning the head and torquing the bolts to specifications.
Caterpillar cat 325 track type excavator (prefix 7 cj) service repair manual ...jdfjskekmdme
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 track type excavator (prefix 7 cj) service repair manual ...cdfzxs
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 l track type excavator (prefix 7cj) service repair manual...jdfjskekmdme
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 l track type excavator (prefix 7cj) service repair manual...hfjsekekmmd
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids. References are made to other documents for additional specifications and guidelines.
Caterpillar cat 325 l track type excavator (prefix 7cj) service repair manual...cdfzxs
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar cat 325 track type excavator (prefix 7 cj) service repair manual ...hfjsekekmmd
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 l track type excavator (prefix 7cj) service repair manual...diskkdkdmdm
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...fuusejkddmmd3e
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...fuusejkddmmd3e
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...dujkdksmdmdm
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...dujkdksmdmdm
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...jdksmmdmdd
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...jdksmmdmdd
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...fujkse9didkke3
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar cat 325 track type excavator (prefix 7 cj) service repair manual ...diskkdkdmdm
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...fjkdksmmdm
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids. Referenced tools and their part numbers are listed.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...fjkdksmmdm
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...orrf0370383
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...orrf0370383
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fuusejkddmmd3e
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fuusejkddmmd3e
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
This document provides an outline and general precautions for a shop manual. It discusses the copyright of the manual, preparation for disassembling equipment, safety procedures, hydraulic and electrical equipment handling, welding repairs, and international unit systems. The outline covers topics to be included in the manual such as specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachment installation procedures.
Kobelco sk380 xdlc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides guidelines and safety precautions for maintenance and repairs of hydraulic excavators. It contains sections on specifications, maintenance procedures, systems overview, disassembly/assembly instructions, troubleshooting, engines, and optional attachment installation. The manual is intended to instruct repair and service technicians on proper procedures. Copyright of the manual belongs to Kobelco Construction Machinery and permission is required for copying or distributing its contents.
More Related Content
Similar to Caterpillar cat 325 b ln excavator (prefix 6dn) service repair manual (6dn00001 and up)
Caterpillar cat 325 l track type excavator (prefix 7cj) service repair manual...hfjsekekmmd
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids. References are made to other documents for additional specifications and guidelines.
Caterpillar cat 325 l track type excavator (prefix 7cj) service repair manual...cdfzxs
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar cat 325 track type excavator (prefix 7 cj) service repair manual ...hfjsekekmmd
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 l track type excavator (prefix 7cj) service repair manual...diskkdkdmdm
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...fuusejkddmmd3e
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...fuusejkddmmd3e
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...dujkdksmdmdm
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...dujkdksmdmdm
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...jdksmmdmdd
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...jdksmmdmdd
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...fujkse9didkke3
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...fujkse9didkke3
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar cat 325 track type excavator (prefix 7 cj) service repair manual ...diskkdkdmdm
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...fjkdksmmdm
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids. Referenced tools and their part numbers are listed.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...fjkdksmmdm
This document provides instructions for installing an inlet manifold on a 325L excavator engine. It describes:
1) Installing a new gasket on the cylinder head and positioning the air inlet manifold.
2) Installing bolts to secure the manifold and connecting air inlet elbows and solenoid.
3) The final step is to install the valve mechanism cover.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual ...orrf0370383
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR (Prefix 7CJ) Service Repair Manual (...orrf0370383
This document provides instructions for removing and installing inlet manifold components on a 325L excavator. The procedures include:
1. Installing a new gasket and positioning the air inlet manifold on the engine.
2. Installing bolts and air inlet elbows on the manifold.
3. Installing the valve mechanism cover to complete the job.
Precautions are provided to keep parts clean and contain fluids.
Caterpillar cat 325 track type excavator service repair manual (6 kk00001 and...diskkdkdmdm
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Caterpillar Cat 325L TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and...fuusejkddmmd3e
This document provides instructions for removing and installing inlet manifold, inlet and exhaust valves, valve guides, and valve seat inserts on a 325L excavator. The procedures describe using specialized tools to compress springs, extract components, and seat inserts. Technicians are advised to keep components clean and refer to other documents for guidance on reusable parts.
Caterpillar Cat 325 TRACK TYPE EXCAVATOR Service Repair Manual (6KK00001 and ...fuusejkddmmd3e
1. The document provides instructions for removing and installing inlet and exhaust valve guides on a 325L excavator engine. It lists the required tools and gives step-by-step procedures for both removal and installation.
2. The removal procedure instructs to use a valve guide driver tool to remove the guides from the cylinder head. For installation, a valve guide driver and guide collar are used to tap and fully seat the guides into the cylinder head.
3. References are provided for determining whether guides can be reused and the proper specifications. Following installation of the guides, the valves are reinstalled per a separate procedure.
Similar to Caterpillar cat 325 b ln excavator (prefix 6dn) service repair manual (6dn00001 and up) (20)
This document provides an outline and general precautions for a shop manual. It discusses the copyright of the manual, preparation for disassembling equipment, safety procedures, hydraulic and electrical equipment handling, welding repairs, and international unit systems. The outline covers topics to be included in the manual such as specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachment installation procedures.
Kobelco sk380 xdlc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides guidelines and safety precautions for maintenance and repairs of hydraulic excavators. It contains sections on specifications, maintenance procedures, systems overview, disassembly/assembly instructions, troubleshooting, engines, and optional attachment installation. The manual is intended to instruct repair and service technicians on proper procedures. Copyright of the manual belongs to Kobelco Construction Machinery and permission is required for copying or distributing its contents.
Kobelco sk300 lc 10 hydraulic excavator service repair manualfjsjjekdkme
This document is a shop manual that provides specifications, maintenance, system, disassembly, troubleshooting, and engine information for a hydraulic excavator model. It contains sections on specifications, maintenance, systems, disassembly, troubleshooting, engine, and installation of options. Safety information is provided throughout, including general safety, safety precautions, and warnings.
Kobelco sk270 srlc 5 (na 2018 yu08) hydraulic excavator service repair manualfjsjjekdkme
This document is the shop manual for a hydraulic excavator. It contains outlines, precautions, and general information for repairing and maintaining the excavator. The manual is divided into chapters covering specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachments. Precautions are provided for safety, preparing for disassembly, hydraulic and electrical equipment, and welding repairs. Copyright information is also included.
Kobelco sk260 lc 10 hydraulic excavator service repair manualfjsjjekdkme
This document outlines general precautions and guidelines for repairing excavator equipment according to the shop manual. It discusses preparing for disassembly, safety practices, hydraulic system repair, electrical work, and welding. Permission is required to copy or distribute content from the copyrighted manual. Measurements use the international unit system. Technicians should thoroughly read and understand the manual before performing any repair work.
Kobelco sk250 10 hydraulic excavator service repair manualfjsjjekdkme
This document outlines general precautions and guidelines for repairing excavator equipment according to the shop manual. It discusses preparing for disassembly, safety during disassembly and assembly, handling hydraulic and electrical equipment, welding repairs, and environmental issues. The outline notes that the copyright belongs to Kobelco and outlines rules for copying or distributing the manual's contents. It also introduces the international unit system used in specifications.
Kobelco sk60 8 hydraulic excavator service repair manualfjsjjekdkme
This document appears to be a shop manual that contains information for maintenance and repair of hydraulic excavators. It includes sections on specifications, maintenance, systems, disassembly, troubleshooting, engines, and optional attachment installation procedures. The document provides safety precautions for repairs and disassembly/assembly. It also includes a table for international unit conversion. The manual is intended as a technical reference for maintenance technicians to perform repairs and find fault equipment.
This shop manual provides information needed for the disassembly, reassembly, and repair of a Kawasaki 135ZV-2 wheel loader. It includes specifications, tightening torques, and service standards for the chassis, power, hydraulic, brake, and operator station systems. Safety precautions and symbols are defined. The manual instructs technicians on removing and installing major components like the engine, transmission, axles, cylinders, and more. Cautions are provided regarding parts handling and use of sealants or lock agents.
This shop manual provides information for performing maintenance and repairs on Kawasaki wheel loaders. It contains safety warnings and symbols, an outline of the loader components and maintenance schedule, recommended lubricants, and sections about inspecting and adjusting the chassis and power groups. Technical details are given for linkage pins, center pins, engine and transmission mounts, and the radiator mount. The purpose is to ensure good machine performance through following the correct maintenance and repair procedures.
Kawasaki 92 z7 wheel loader service repair manualfjsjjekdkme
This document provides specifications for the 90Z7 and 92Z7 wheel loaders. The 90Z7 is powered by a Hino E13C-VV diesel engine and has operating weights ranging from 24550-24870 kg. The 92Z7 also uses a Hino E13C-VV diesel engine and has operating weights from 26840-27090 kg. Both models have 4 speeds in forward and reverse and an articulation angle of 37 degrees left and right. Dimensional specifications like overall length, width, height and other measurements are provided for each model/bucket type.
Kawasaki 92 z7 wheel loader operation and maintenance manualfjsjjekdkme
The document provides safety instructions and component information for operating heavy machinery. It outlines proper procedures for starting and using the machine, transporting loads, and performing maintenance safely. Operators must follow guidelines to prevent injuries or accidents from improper or unsafe operation. The manual describes the various controls, switches, and components in the operator cab.
Kawasaki 90 z7 wheel loader service repair manualfjsjjekdkme
This document provides specifications for the 90Z7 and 92Z7 wheel loaders. The 90Z7 is powered by a Hino E13C-VV diesel engine and has operating weights ranging from 24550-24870 kg. The 92Z7 also uses a Hino E13C-VV diesel engine and has operating weights from 26840-27090 kg. Both models have 4 speeds in forward and reverse and an articulation angle of 37 degrees left and right. Dimensional specifications like overall length, width, height and other measurements are provided for each model/bucket type.
Kawasaki 90 z7 wheel loader operation and maintenance manualfjsjjekdkme
The document provides safety instructions and component descriptions for a machine. It outlines various hazards to avoid when operating or servicing the machine, such as ensuring safety before leaving the operator's seat, wearing protective clothing, and avoiding contact with moving parts. It also describes the machine's components, including the operator's station, consoles, switches, and monitoring systems. Maintenance procedures should follow safety practices like supporting the machine properly and avoiding high-pressure fluids.
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 9001 and up)fjsjjekdkme
This document provides guidelines and precautions for disassembling and reassembling a wheel loader. It discusses preparing the work area, inspecting components, draining fluids, cleaning parts, applying lubricants, and ensuring proper tightening of fasteners. Special attention should be given to sliding surfaces, seals, and markings for reassembly. Tools and loose parts should be accounted for after completion. Floating seals and nylon slings require special handling to prevent damage or improper installation.
Kawasaki 90 z6 wheel loader service repair manual (serial no. 90c7 0101 and up)fjsjjekdkme
This document provides specifications and component layout information for a 90Z6 wheel loader.
The specifications section lists operating weights, engine details, dimensions, speeds and other technical specifications for the GSC and LSC models.
The component layout sections include diagrams and lists showing the layout and weights of major components such as the chassis, powertrain, hydraulic, electrical and other systems. Component names, locations and approximate weights are provided.
Kawasaki 90 z6 wheel loader parts catalogue manual (serial no. 90c7 9001 and up)fjsjjekdkme
This document is a parts catalog for a wheel loader model 90Z6 powered by a Cummins QSM11 engine. It lists parts grouped by system including the front axle, rear axle, power train, engine systems, cab, chassis, electrical systems, hydraulic system, brake system and loader attachments. The document provides part numbers, part names, quantities and the applicable serial number range for each part listed.
Kawasaki 85 z7 wheel loader service repair manual (serial no. 85j1 5001 and up)fjsjjekdkme
This document provides specifications and layout diagrams for the components of a wheel loader. It includes:
- Specifications for dimensions, weights, engine details, speeds, and more.
- Overview diagrams showing the layout of main components such as the bucket, cylinders, lights, engine, and more.
- Detailed diagrams labeling locations of the engine, radiator, filters, tanks, valves, pumps, axles, and other parts.
- An overview of the electric system components around the cab, hydraulic oil tank, fuel tank, and engine.
- Sections providing specifications for the engine, hydraulic and electrical components.
The document contains detailed information on the specifications, component layout and electrical
Kawasaki 80 z7b wheel loader service repair manual (serial no. 80c8 5001 and up)fjsjjekdkme
The document contains sections from a shop manual for a wheel loader. It includes sections on general information, component layout, specifications, and maintenance procedures. The component layout sections describe and illustrate the main components of the wheel loader including the engine, hydraulic system, electrical system, cab, drive unit, and other key components. The specifications section lists technical specifications for the engine, operating weights, dimensions, travel speeds and other performance specifications.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01328419
Inlet Manifold - Remove
SMCS - 1058-011
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
1/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Dispose of all fluids according to local regulations and mandates.
1. Disconnect air inlet piping from the turbocharger to the aftercooler, if necessary.
Illustration 1 g00629952
2. Remove bolts (1) and disconnect air inlet heater solenoid (3).
3. Remove air inlet elbows (2) from air inlet manifold (5).
4. Remove bolts (4) from air inlet manifold (5).
5. Remove air inlet manifold (5) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:22:09 UTC+0800 2020
2/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01414226
Inlet Manifold - Install
SMCS - 1058-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00675794
1. Install a new gasket (6) on the cylinder head.
Illustration 2 g00629952
2. Position the air inlet manifold (5) on the engine.
3. Install bolts (4). Tighten the bolts to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
4. Install air inlet elbows (2) on air inlet manifold (5).
5. Install bolts (1) and connect air inlet heater solenoid (3).
End By:
a. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:23:04 UTC+0800 2020
2/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01943334
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
Start By:
a. Remove the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
1/5
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 1 g01011225
Note: The following components of the exhaust valves are different from the components of
the inlet valves: spring retainer (2), valve spring (3) and valve (5).
Illustration 2 g01011269
1. Use Tooling (A) to compress valve spring (3). Remove retainer lock (1).
2. Remove Tooling (A).
3. Remove spring retainer (2). Remove valve spring (3).
2/5
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 4. Remove valve seal (4) and valve (5).
5. Repeat Steps 1 through 4 in order to remove the remaining inlet valves and exhaust valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 5S-1330 Valve Spring Compressor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the inlet valves, the exhaust valves and the springs,
refer to Guideline For Reusable Parts And Salvage Operations, SEBF8002, "Valves, Valve
Springs, Valve Rotators, and Locks", Guideline For Reusable Parts And Salvage Operations,
SEBF8034, "Valve and Valve Spring Specifications", and Guideline For Reusable Parts And
Salvage Operations, SEBF8162, "Specifications to Measure and Salvage Cylinder Head
Assemblies and Related Components".
3/5
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g01011225
1. Lubricate valve (5) with clean engine oil. Install valve (5) in the cylinder head assembly.
Install new valve seal (4) against the valve guide.
2. Place the following items on the valve stem: valve spring (3) and spring retainer (2).
The valve keepers can be thrown from the valve when the valve spring
compressor is released. Ensure that the valve keepers are properly
installed on the valve stem. To help prevent personal injury, keep away
from the front of the valve keepers and valve springs during the
installation of the valves.
Note: A small amount of grease can be used to hold retainer locks (1) in position during
installation.
4/5
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 4 g01011269
3. Use Tooling (A) to compress valve spring (3). Install retainer lock (1).
4. Repeat Steps 1 through 3 in order to install the remaining inlet valves and exhaust valves.
End By:
a. Install the cylinder head assembly. Refer to Disassembly and Assembly, "Cylinder Head -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:24:00 UTC+0800 2020
5/5
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01961680
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Asseblies 3114, 3116, and
3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162, "Procedure
to Measure and Salvage Cylinder Head Assemblies and Related Components".
1/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00745735
Typical example
1. Use Tooling (A) to remove the inlet valve guides from the cylinder head assembly. Use
Tooling (A) to remove the exhaust valve guides from the cylinder head assembly.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7793 Valve Guide Driver (1)
1
B 1U-7792 Guide Collar (1)
1
C 9U-6895 Valve Guide Driver 1
D 149-4008 Guide Collar 1
( 1 )
Part of 1U-6685 Valve Guide Tool Kit
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Note: For information on the reusability of the valve guides, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines" and Guideline For Reusable Parts And Salvage Operations, SEBF8162,
"Procedure to Measure and Salvage Cylinder Head Assemblies and Related Components".
Illustration 2 g00745782
Typical example
1. Position inlet valve guide (1) and tap on the top of inlet valve guide (1). This is done in
order to start inlet valve guide (1) into the cylinder head assembly.
2. Use Tooling (A) and Tooling (B) to install inlet valve guide (1). Install inlet valve guides
(1) until tooling (B) contacts the cylinder head.
3/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g00745672
Typical example
3. Position exhaust valve guide (2) and tap on the top of exhaust valve guide (2). This is done
in order to start the exhaust valve guide into the cylinder head assembly.
Note: Some of the early engines have inlet valves and exhaust valves that are identical in
size. Use the same specifications and the same tools for both valves. Proceed to Step 4 if the
valves are not the same size.
4. Use Tooling (C) and Tooling (D) to install exhaust valve guide (2). Install inlet valve guides
(2) until tooling (D) contacts the cylinder head.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:24:56 UTC+0800 2020
4/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929146
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
6V-4194 Valve Seat Extractor 1
B(1)
165-5647 Valve Seat Extractor 1
C(1)
6V-4804 Handle 1
D(1)
6V-4192 Threaded Shaft 1
E(1)
6V-4199 Lifting Bracket 1
(1)
Part of the 166-7441 Valve Seat Extractor Tool
Start By:
a. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
Illustration 1 g00615519
Illustration 2 g00656459
Note: Replace Tooling (A) with Tooling (B) for the removal of the inlet valve seat insert.
1. Install Tooling (A) in the exhaust valve seat insert.
2. Install Tooling (C) and Tooling (D) in Tooling (A). Hand tighten Tooling (D). Tooling (A)
will expand below the edge of valve seat insert (1).
2/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00656462
3. Install Tooling (E) on the cylinder head under Tooling (C). Hold Tooling (D) while you turn
Tooling (C). Remove valve seat insert (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
F 1U-6685 Guide and Insert Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: For information on the reusability of the valve seats, refer to Guideline For Reusable Parts
And Salvage Operations, SEBF8218, "Specifications for Cylinder Head Assemblies 3114, 3116,
and 3126 Engines".
1. Cool the valve seat inserts for easier installation.
3/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 4 g01003799
2. Turn Tooling (F) upside-down and use Tooling (F) and a press to install the valve seat
inserts in the cylinder head assembly.
3. After the valve seat inserts are installed, grind the inserts to the final specification. Refer to
Guideline for Reusable Parts and Salvage Operation, SEBF8218, "Specifications for
Cylinder Head Assemblies 3114, 3116, and 3126 Engines" for the specifications.
End By:
a. Install the inlet valves and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:25:52 UTC+0800 2020
4/4
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929163
Engine Oil Filter Base - Remove
SMCS - 1306-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench 1
Start By:
a. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01009468
1. Use Tooling (A) to remove engine oil filter (3).
2. Disconnect the tube assembly for the turbocharger inlet (1) from the engine oil filter base
(4).
3. Remove bolts (2) and the washers that hold engine oil filter base (4) to the cylinder block.
4. Remove engine oil filter base (4) and the gasket.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:26:48 UTC+0800 2020
2/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929612
Engine Oil Filter Base - Disassemble
SMCS - 1306-015
Disassembly Procedure
Start By:
a. Remove the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Remove".
Illustration 1 g01011623
Personal injury can result from being struck by parts propelled by a
released spring force.
1/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove plugs (1) and (3) from oil filter base (2).
Illustration 2 g01011627
2. Remove springs (4) and valves (6). Remove O-ring seals (5) from plugs (1) and (3). Inspect
the parts for wear or damage. If the parts are worn or damaged, use new parts for
replacement.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:27:43 UTC+0800 2020
2/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i01929615
Engine Oil Filter Base - Assemble
SMCS - 1306-016
Assembly Procedure
Illustration 1 g01011627
1. Install O-ring seals (5) onto plugs (1) and (3). Install valves (6) and springs (4).
1/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 2 g01011623
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install plugs (1) and (3) onto oil filter base (2).
End By:
a. Install the engine oil filter base. Refer to Disassembly and Assembly, "Engine Oil Filter
Base - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Jul 18 17:28:39 UTC+0800 2020
2/2
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325B L EXCAVATOR 6DN
Configuration: 325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine
Disassembly and Assembly
446 and 446B Backhoe Loaders, Lexion 450 Combine, 3114 and 3116 Engines,
IT18F Integrated Toolcarrier, D6M Track-Type Tractor and 928F, 950F and 950G
Wheel Loaders
Media Number -SENR3611-18 Publication Date -01/05/2009 Date Updated -27/05/2009
i02376426
Engine Oil Filter Base - Install
SMCS - 1306-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01009468
1/3
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engi...
2020/7/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...