The document provides instructions for disassembling the final drive of an excavator. Key steps include:
1. Marking the final drive for alignment and securing it to a repair stand.
2. Removing bolts and lifting devices to extract the cover and internal gears and shafts.
3. Using retaining ring pliers and presses to separate additional components like carriers.
4. Hammering out pins to dismantle planetary gear sets from within the carriers.
Caterpillar cat 324 d l excavator (prefix ejc) service repair manual (ejc0000...fjskekdmmem
The document provides disassembly instructions for a final drive component in 3 steps or less:
1. Clean and mark the final drive assembly. Remove the cover and disassemble the internal gears.
2. Remove the carrier assemblies and disassemble them by pressing out the shafts and removing the thrust washers and bearings.
3. Remove the remaining gears and spacers from the housing to fully disassemble the final drive.
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...zan2736ban
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...fujkskemdmdm4r
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...f8uesjdkdmdm
The document provides instructions for disassembling a final drive component. It lists required tools and outlines 33 steps to remove parts like the cover, carrier assembly, ring gears, and seals. Cleanliness is important to prevent dirt from entering during reassembly. Weights of removed parts are provided to assist with lifting.
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar cat 324 d l excavator (prefix ejc) service repair manual (ejc0000...fjskekdmmem
The document provides disassembly instructions for a final drive component in 3 steps or less:
1. Clean and mark the final drive assembly. Remove the cover and disassemble the internal gears.
2. Remove the carrier assemblies and disassemble them by pressing out the shafts and removing the thrust washers and bearings.
3. Remove the remaining gears and spacers from the housing to fully disassemble the final drive.
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...zan2736ban
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
Caterpillar Cat 324D and 324D L Excavator (Prefix T2D) Service Repair Manual ...fujkskemdmdm4r
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...f8uesjdkdmdm
The document provides instructions for disassembling a final drive component. It lists required tools and outlines 33 steps to remove parts like the cover, carrier assembly, ring gears, and seals. Cleanliness is important to prevent dirt from entering during reassembly. Weights of removed parts are provided to assist with lifting.
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...km7seydwuhdw
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...ufjksemd8ujd
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
The document provides instructions to disassemble a final drive assembly in 3 steps:
1. Remove the cover from the final drive assembly by lifting it with tooling.
2. Remove bolts and internal gear components from the cover.
3. Inspect and replace the check plate if wear is shown, and remove plugs from the cover.
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...8ufjsekddm8u
The document provides instructions to disassemble a final drive assembly in 3 steps:
1. Remove the cover from the final drive assembly by lifting it with tooling.
2. Remove bolts and internal gear components from the cover.
3. Inspect and replace the check plate if wear is shown. Remove plugs from the cover.
The document provides instructions to disassemble a final drive for an excavator. Key steps include:
1. Removing the final drive cover and gears.
2. Removing the carrier assembly and planetary gears.
3. Using presses and tools to remove shafts, gears, and bearings from the housing and carrier assembly.
Cleanliness is important to prevent dirt from entering during disassembly. Parts must be reinstalled in their original locations.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...prmy389342
The document provides instructions to disassemble a final drive for an excavator. Key steps include:
1. Removing the final drive cover and gears.
2. Removing the carrier assembly and planetary gears.
3. Using presses and tools to extract shafts, gears, and bearings from housings and other components.
Cleanliness is emphasized to prevent dirt from entering internal parts during disassembly.
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...jdkskmdmdm
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...f7fujksekmdm8u
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar cat 324 d excavator (prefix t2d) service repair manual (t2d00001 ...ujdkdkdmdm
The document provides instructions for disassembling a final drive component with 33 steps. It begins by removing the final drive and cleaning the exterior. Key steps include fastening the final drive to a repair stand, removing the cover using lifting tools, and dismantling internal parts like gears, shafts, seals, and housings through the use of specialized tools like pullers and hammers. The goal is to separate all individual parts for inspection or replacement.
Caterpillar cat 324 d excavator (prefix t2d) service repair manual (t2d00001 ...fjskekazswdmme
The document provides instructions to disassemble a final drive assembly in 3 steps:
1. Remove the cover and internal gears from the final drive housing.
2. Remove the carrier assemblies that contain the planetary gears.
3. Disassemble the carrier assemblies by removing the planetary shafts, thrust washers, and gears.
Caterpillar cat 324 d l excavator (prefix t2d) service repair manual (t2d0000...fhhsjdkmem
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
The document provides instructions for disassembling a final drive component in 3 steps:
1. Remove the cover and internal gears/shafts from the final drive housing.
2. Disassemble the carrier assemblies within the housing to remove planetary gears.
3. Extract the remaining gears and spacers from the housing to fully disassemble it.
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...f7fujksekmdm8u
The document provides instructions for disassembling the final drive of a 324D L excavator. Key steps include:
1. Marking the final drive sections and fastening it to a repair stand.
2. Removing the cover bolts and setscrews, then lifting the cover off using tooling.
3. Removing bolts from the gear, checking the plate, and removing plugs from the cover.
Caterpillar Cat 324D L Excavator (Prefix TSN) Service Repair Manual (TSN00001...f7fujksekmdm8u
This document provides the disassembly procedure for a service repair manual of excavator models 324D and 324D L. It outlines 28 steps to disassemble the travel motor, including removing components like the head, O-rings, plates, springs, piston assemblies, seals, and covers. Tools required include an adapter, nuts, threaded rod, eyebolt, retaining ring pliers, bearing puller, and thread lock compound. Cleanliness is emphasized and all O-rings and gaskets must be replaced during assembly.
Caterpillar Cat 324D L Excavator (Prefix TRH) Service Repair Manual (TRH00001...f7fujksekmdm8u
This document provides the disassembly and assembly procedures for a 324D LN excavator travel motor. It includes 28 steps for disassembly that remove components like the motor head, seals, plates, discs, bearings, and housing pieces. The 28 steps for assembly install these same components in reverse order and include notes about cleaning, applying lubricant, and ensuring correct part positioning. Tools required are also listed.
Caterpillar Cat 324D L Excavator (Prefix PYT) Service Repair Manual (PYT00001...f7fujksekmdm8u
This document provides instructions for disassembling and assembling the final drive of a 324D L Excavator. It lists 37 steps for disassembly, removing components like gears, shafts, seals and housings. It then lists 7 steps for assembly, including installing bearings, determining the correct shim thickness to preload the bearings, and reinstalling components in reverse order of disassembly. Cleanliness is emphasized throughout and tools including various link brackets and eyebolts are listed.
The document provides instructions for disassembling the final drive of a 324D excavator. It lists required tools and a multi-step process involving removing bolts, covers, gears, seals, and other components. Individual parts are removed using various tools, with attention to alignment marks and component weights. The carrier assembly, ring gears, and housing components are then further disassembled to access internal planetary gears and bearings.
Caterpillar Cat 324D L Excavator (Prefix MND) Service Repair Manual (MND00001...f7fujksekmdm8u
The document provides instructions for disassembling a final drive assembly. Key steps include removing the cover, gears, carrier assembly, planetary carrier, and planetary gears. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be reinstalled in their original locations and alignment marks can aid this. Various tools are required, including link brackets and eyebolts to lift components by weight.
Caterpillar Cat 324D L Excavator (Prefix JZR) Service Repair Manual (JZR00001...f7fujksekmdm8u
This document provides the disassembly and assembly procedures for a travel motor in a 324D or 324D L excavator. It includes 28 steps for disassembly that remove components like the head, seals, springs, plates, and pistons. The 27 steps for assembly install these components in reverse order, noting that all seals and pins must be replaced and components cleaned before assembly. Proper tooling is required and safety precautions mentioned.
More Related Content
Similar to Caterpillar Cat 324D LN Excavator (Prefix EJC) Service Repair Manual (EJC00001 and up).pdf
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...km7seydwuhdw
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...ufjksemd8ujd
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
The document provides instructions to disassemble a final drive assembly in 3 steps:
1. Remove the cover from the final drive assembly by lifting it with tooling.
2. Remove bolts and internal gear components from the cover.
3. Inspect and replace the check plate if wear is shown, and remove plugs from the cover.
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...8ufjsekddm8u
The document provides instructions to disassemble a final drive assembly in 3 steps:
1. Remove the cover from the final drive assembly by lifting it with tooling.
2. Remove bolts and internal gear components from the cover.
3. Inspect and replace the check plate if wear is shown. Remove plugs from the cover.
The document provides instructions to disassemble a final drive for an excavator. Key steps include:
1. Removing the final drive cover and gears.
2. Removing the carrier assembly and planetary gears.
3. Using presses and tools to remove shafts, gears, and bearings from the housing and carrier assembly.
Cleanliness is important to prevent dirt from entering during disassembly. Parts must be reinstalled in their original locations.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...prmy389342
The document provides instructions to disassemble a final drive for an excavator. Key steps include:
1. Removing the final drive cover and gears.
2. Removing the carrier assembly and planetary gears.
3. Using presses and tools to extract shafts, gears, and bearings from housings and other components.
Cleanliness is emphasized to prevent dirt from entering internal parts during disassembly.
The document provides instructions to disassemble a final drive assembly in 3 steps:
1) Remove the cover from the final drive assembly by lifting it with tooling.
2) Remove bolts and internal gear components from the cover.
3) Remove O-rings from plugs that were in the cover.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...jdkskmdmdm
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar Cat 324D L Excavator (Prefix T2D) Service Repair Manual (T2D00001...f7fujksekmdm8u
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
Caterpillar cat 324 d excavator (prefix t2d) service repair manual (t2d00001 ...ujdkdkdmdm
The document provides instructions for disassembling a final drive component with 33 steps. It begins by removing the final drive and cleaning the exterior. Key steps include fastening the final drive to a repair stand, removing the cover using lifting tools, and dismantling internal parts like gears, shafts, seals, and housings through the use of specialized tools like pullers and hammers. The goal is to separate all individual parts for inspection or replacement.
Caterpillar cat 324 d excavator (prefix t2d) service repair manual (t2d00001 ...fjskekazswdmme
The document provides instructions to disassemble a final drive assembly in 3 steps:
1. Remove the cover and internal gears from the final drive housing.
2. Remove the carrier assemblies that contain the planetary gears.
3. Disassemble the carrier assemblies by removing the planetary shafts, thrust washers, and gears.
Caterpillar cat 324 d l excavator (prefix t2d) service repair manual (t2d0000...fhhsjdkmem
The document provides instructions to disassemble a final drive. Key steps include:
1. Removing the cover and gears from the final drive housing.
2. Using tools to remove the carrier assembly and planetary gears.
3. Pressing the shafts out of the carrier assembly and disassembling it.
The document provides instructions for disassembling a final drive component in 3 steps:
1. Remove the cover and internal gears/shafts from the final drive housing.
2. Disassemble the carrier assemblies within the housing to remove planetary gears.
3. Extract the remaining gears and spacers from the housing to fully disassemble it.
Similar to Caterpillar Cat 324D LN Excavator (Prefix EJC) Service Repair Manual (EJC00001 and up).pdf (15)
Caterpillar Cat 324D L Excavator (Prefix JJG) Service Repair Manual (JJG00001...f7fujksekmdm8u
The document provides instructions for disassembling the final drive of a 324D L excavator. Key steps include:
1. Marking the final drive sections and fastening it to a repair stand.
2. Removing the cover bolts and setscrews, then lifting the cover off using tooling.
3. Removing bolts from the gear, checking the plate, and removing plugs from the cover.
Caterpillar Cat 324D L Excavator (Prefix TSN) Service Repair Manual (TSN00001...f7fujksekmdm8u
This document provides the disassembly procedure for a service repair manual of excavator models 324D and 324D L. It outlines 28 steps to disassemble the travel motor, including removing components like the head, O-rings, plates, springs, piston assemblies, seals, and covers. Tools required include an adapter, nuts, threaded rod, eyebolt, retaining ring pliers, bearing puller, and thread lock compound. Cleanliness is emphasized and all O-rings and gaskets must be replaced during assembly.
Caterpillar Cat 324D L Excavator (Prefix TRH) Service Repair Manual (TRH00001...f7fujksekmdm8u
This document provides the disassembly and assembly procedures for a 324D LN excavator travel motor. It includes 28 steps for disassembly that remove components like the motor head, seals, plates, discs, bearings, and housing pieces. The 28 steps for assembly install these same components in reverse order and include notes about cleaning, applying lubricant, and ensuring correct part positioning. Tools required are also listed.
Caterpillar Cat 324D L Excavator (Prefix PYT) Service Repair Manual (PYT00001...f7fujksekmdm8u
This document provides instructions for disassembling and assembling the final drive of a 324D L Excavator. It lists 37 steps for disassembly, removing components like gears, shafts, seals and housings. It then lists 7 steps for assembly, including installing bearings, determining the correct shim thickness to preload the bearings, and reinstalling components in reverse order of disassembly. Cleanliness is emphasized throughout and tools including various link brackets and eyebolts are listed.
The document provides instructions for disassembling the final drive of a 324D excavator. It lists required tools and a multi-step process involving removing bolts, covers, gears, seals, and other components. Individual parts are removed using various tools, with attention to alignment marks and component weights. The carrier assembly, ring gears, and housing components are then further disassembled to access internal planetary gears and bearings.
Caterpillar Cat 324D L Excavator (Prefix MND) Service Repair Manual (MND00001...f7fujksekmdm8u
The document provides instructions for disassembling a final drive assembly. Key steps include removing the cover, gears, carrier assembly, planetary carrier, and planetary gears. Cleanliness is important to prevent dirt from entering during disassembly. Parts must be reinstalled in their original locations and alignment marks can aid this. Various tools are required, including link brackets and eyebolts to lift components by weight.
Caterpillar Cat 324D L Excavator (Prefix JZR) Service Repair Manual (JZR00001...f7fujksekmdm8u
This document provides the disassembly and assembly procedures for a travel motor in a 324D or 324D L excavator. It includes 28 steps for disassembly that remove components like the head, seals, springs, plates, and pistons. The 27 steps for assembly install these components in reverse order, noting that all seals and pins must be replaced and components cleaned before assembly. Proper tooling is required and safety precautions mentioned.
Caterpillar Cat 324D L Excavator (Prefix JAT) Service Repair Manual (JAT00001...f7fujksekmdm8u
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D and 324D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves applying thread lock compound and ensuring proper installation of keys, seals, and bearing races. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 324D L Excavator (Prefix DFP) Service Repair Manual (DFP00001...f7fujksekmdm8u
This service repair manual provides instructions for repairing Caterpillar 324D and 324D L excavators with C7 engines. It describes how to remove and install various engine components like the front housing, camshaft idler gear, valve mechanism cover, and valve mechanism cover base. The procedures provide the required tools and step-by-step instructions for each repair, emphasizing the need to keep components clean and free of contaminants.
Caterpillar Cat 324D L Excavator (Prefix CJX) Service Repair Manual (CJX00001...f7fujksekmdm8u
1) The documents provide instructions for removing and installing various engine components on a 324D excavator, including the flywheel, crankshaft rear seal, flywheel housing, vibration damper, and crankshaft front seal.
2) The procedures describe using various tools to remove components like the flywheel and seals, and reinstalling them in the reverse order. Precautions are given to keep parts clean and contain fluids.
3) Detailed illustrations and torque specifications are provided to correctly position and tighten components like the flywheel housing, crankshaft pulley, and seal during installation.
Caterpillar Cat 324D L Excavator (Prefix BTK) Service Repair Manual (BTK00001...f7fujksekmdm8u
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D L and 324D LN. The disassembly procedure is outlined in 28 steps and includes removing components like the head, seals, springs, plates, and bearings. The assembly procedure is outlined in 15 steps and includes installing components in the reverse order of disassembly and applying thread lock compound to seals. Tools required are also listed.
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D and 324D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure instructs to install components in the reverse order and notes that all seals and gaskets must be replaced, parts must be cleaned before assembly, and lubricant applied to components. Proper tooling is listed for removing and installing retaining rings, seals, and races.
This document provides the disassembly and assembly procedures for a travel motor in a 324D or 324D L excavator. It includes 28 steps for disassembly that remove components like the head, seals, springs, plates, and pistons. The 27 steps for assembly install these components in reverse order, noting that all seals and pins must be replaced and components cleaned before assembly. Proper tooling is required and safety precautions mentioned.
This service repair manual provides instructions for repairing Caterpillar 324D and 324D L excavators with C7 engines. It describes how to remove and install various engine components like the front housing, camshaft idler gear, valve mechanism cover, and valve mechanism cover base. The procedures provide the required tools and step-by-step instructions for each repair, emphasizing the need to keep components clean and free of contaminants.
This document provides the disassembly and assembly procedures for a travel motor on excavator models 324D and 324D L. The disassembly procedure involves 28 steps to remove components from the travel motor including the head, springs, plates, seals, bearings, and housing cover. The assembly procedure reverses the disassembly steps and involves applying thread lock compound and ensuring proper installation of keys, seals, and bearing races. Cleanliness is emphasized throughout to prevent contamination.
This document provides instructions for removing and installing various engine components on a Caterpillar 324D excavator powered by a C7 engine. The components include:
- The flywheel, which is removed using lifting brackets and guide bolts.
- The crankshaft rear seal, which is removed using a drill bit and slide hammer puller.
- The flywheel housing, which is removed after draining fluids using lifting brackets and bolts.
- The vibration damper and pulley, which are removed after loosening bolts and removing the drive belt.
Caterpillar Cat 323F L Excavator (Prefix NCW) Service Repair Manual (NCW00001...f7fujksekmdm8u
This document provides instructions for removing and installing the cylinder head on a Caterpillar C7.1 engine. The removal process involves draining coolant, disconnecting wiring harnesses and sensors, and removing mounting brackets. Bolts are then loosened in a specific sequence before lifting the cylinder head off. Installation requires cleaning surfaces, installing a new gasket, and lifting the cylinder head into place using guide studs before tightening bolts in the reverse removal sequence.
Caterpillar Cat 323D2 L Excavator (Prefix YCR) Service Repair Manual (YCR0000...f7fujksekmdm8u
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, check valves, fittings, brake piston, friction plates, barrel assembly and shaft. The assembly process describes 25 steps and includes applying sealant, installing seals, plates, springs and other components in the correct order and orientation. Special care must be taken with keys and pins to prevent damage during assembly.
Caterpillar Cat 323D2 L Excavator (Prefix XBK) Service Repair Manual (XBK0000...f7fujksekmdm8u
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the head, brake piston, barrel assembly, and shaft assembly. The assembly process describes 25 steps and includes installing seals, plates, springs and ensuring proper alignment of components. Special tools and precautions are noted to correctly reinstall parts in their original positions and prevent damage during the travel motor's reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...f7fujksekmdm8u
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, which include removing the head, brake piston, barrel assembly, and other components. It then lists 13 steps for assembly, which involve installing seals, the shaft assembly, cam plate, springs and other parts back into the travel motor body. Safety precautions are noted, such as containing fluids and applying sealant to surfaces.
Kalyan chart DP boss guessing matka results➑➌➋➑➒➎➑➑➊➍
8328958814Satta Matka is a number-based game. There are several markets, each with its owner responsible for releasing the lottery satta Matka market results on time. Kalyan market, Worli market, main Mumbai market, Rajdhani market, and Milan market are some of the main markets or bazaars involved in the satta Matka game. The oldest and most legitimate markets are in Kalyan and Main Mumbai. Every Satta Market has an open and close time. The satta results for these markets are published on or shortly after the open and close times. During the open result, two numbers are decoded, one of which is a three-digit number and the other a single-digit number. Similarly, three-digit and single-digit numbers are declared during the satta market's close. The last digit after adding the three digits of the open or close result is usually the single digit declared during the open and close results.KALYAN MATKA | MATKA RESULT | KALYAN MATKA TIPS | SATTA MATKA | MATKA.COM | MATKA PANA JODI TODAY | BATTA SATKA | MATKA PATTI JODI NUMBER | MATKA RESULTS | MATKA CHART | MATKA JODI | SATTA COM | FULL RATE GAME | MATKA GAME | MATKA WAPKA | ALL MATKA RESULT LIVE ONLINE | MATKA RESULT | KALYAN MATKA RESULT | DPBOSS MATKA 143 | MAINSATTA MATKA SATTA FAST RESULT KALYAN TOP MATKA RESULT KALYAN SATTA MATKA FAST RESULT MILAN RATAN RAJDHANI MAIN BAZAR MATKA FAST TIPS RESULT MATKA CHART JODI CHART PANEL CHART FREE FIX GAME SATTAMATKA ! MATKA MOBI SATTA 143 spboss.in TOP NO1 RESULT FULL RATE MATKA ONLINE GAME PLAY BY APP SPBOSSdp boss net, dp satta, dpboss dpboss, indian satta matka, kalyan matkà result today , matka boss, matka result live, matka satta result today, satamatka com, satta boss, satta matka king, sattamatkà, sattamatkà result, sattamatta com, sattmatka sattmatka, star matka, tara matka, tara satta matka, worli matka, indian matka, matka live, kalyan guessing, satta fix, kalyan final ank, dp matka, dpboss net, sata mata com, सट्टा मटका, sattamatkà 143, golden matka, satta matta matka 143, satta fast, kalyan open, satta 143, dpboss 143 guessing, dpboss satta, golden satta matka, satta bajar
Satta Matka Market is India's leading website providing the quickest sattamatka outcome, experienced in Satta Matka game. Our services include free Satta Matka Trick and Tips for Kalyan Matka and Disawar Satta King, as well as satta matka graphs, online play, tips and more. Our team of experts strive to help you recoup your losses quickly through our proposals such as Free Satta Matka Tips and Kalyan Bazar Tips. We are known as India's best Matka DpBoss portal site, here to deliver updates on all sorts of Satta Market like Kalyan Bazar, Milan, Rajdhani, Time Bazaar, Main and the most current charts. Stay tuned with us for more live updates on the Satta market
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Automotive Engine Valve Manufacturing Plant Project Report.pptxSmith Anderson
The report provides a complete roadmap for setting up an Automotive Engine Valve. It covers a comprehensive market overview to micro-level information such as unit operations involved, raw material requirements, utility requirements, infrastructure requirements, machinery and technology requirements, manpower requirements, packaging requirements, transportation requirements, etc.
2. Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 154-6181 Forcing Screw 1
D 138-7574 Link Bracket 2
E
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F 1U-8846 Gasket Sealant 1
Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3/12
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
Illustration 3 g00708091
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
4/12
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00708235
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
Illustration 5 g00708092
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
Illustration 6 g01304883
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
5/12
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 7 g00708144
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
Illustration 8 g00708218
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
6/12
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g00708162
13. Remove sun gear (14) from carrier assembly (15).
Illustration 10 g00708325
14. Remove spacer (16).
Illustration 11 g00708184
Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
7/12
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 12 g00708360
16. Use a screwdriver or a chisel in order to separate the two ring gears (17).
Note: The two ring gears are held together with Tooling (F). It may be necessary to heat the
ring gears in order to soften the sealant. Do not heat over 135 °C (275 °F) for more than
thirty minutes.
Illustration 13 g00708172
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
Illustration 14 g00708175
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
8/12
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g00708370
Illustration 16 g00708220
b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
9/12
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g00708186
22. Remove O-ring seal (24) from main housing (18).
Illustration 18 g00708187
23. Remove bolts (25) from gear (26).
Illustration 19 g00708202
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from the main housing (18) once gear (26) is
removed. Make sure that the motor housing is supported.
10/12
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g00708211
25. Remove shims (27) from the main housing.
Illustration 21 g00708212
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from the motor housing (28). The combined weight of main housing (18) and the
final drive sprocket is approximately 82 kg (180 lb).
Illustration 22 g00708214
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
11/12
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g00708215
Illustration 24 g00708216
30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jul 21 11:51:19 UTC+0800 2020
12/12
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 324D LN EXCAVATOR EJC
Configuration: 324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine
Disassembly and Assembly
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power
Unit Machine Systems
Media Number -RENR8646-22 Publication Date -01/02/2015 Date Updated -12/09/2018
i02783051
Final Drive - Disassemble
SMCS - 4050-015
S/N - A3R1-1021
S/N - AZP1-UP
S/N - DBH1-UP
S/N - EJC1-643
S/N - GBR1-UP
S/N - GPB1-801
S/N - JJG1-813
S/N - KBE1-UP
S/N - LAB1-415
S/N - LAL1-250
S/N - MCL1-201
S/N - NAC1-250
S/N - PAL1-UP
S/N - PKE1-814
S/N - SCR1-774
S/N - SYM1-617
1/13
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. S/N - T2D1-322
S/N - T2S1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 194-3878 Spanner Socket 1
E 138-7574 Link Bracket 2
F
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
G
1U-7600 Slide Hammer Puller Gp 1
8T-0266 Bolt 1
Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.
Note: Some of the images that are in this procedure do not show the sprocket assembly that
is attached to the final drive housing. If necessary, the weights that are given include the
weight of the sprocket assembly.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
2/13
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The weight of the final drive assembly is
approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. Remove the cover. The weight of the cover is approximately 32 kg
(70 lb).
Illustration 3 g00879362
3/13
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 5. Remove bolts (3). Remove gear (5). Check plate (6). Replace plate (6) if wear is shown.
Remove plugs (4) from cover (2).
Illustration 4 g00879365
6. Remove O-ring seal (7) from plugs (4).
Illustration 5 g00780428
7. Remove gear (8). Remove spacer (9).
Illustration 6 g00780432
4/13
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 8. Remove retaining ring (10) with Tooling (C). Remove washer (11). Remove gear (12).
Remove bearing assembly (13). Remove second washer (11).
9. Repeat Step 8 for the remaining two gear assemblies.
Illustration 7 g00781401
10. Remove retaining ring (14).
Illustration 8 g00781407
11. Remove carrier assembly (15).
5/13
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 9 g01389593
12. Use a suitable press in order to remove the shafts from carrier assembly (15).
Illustration 10 g00781412
13. Remove gear (16). Remove spacer (17).
Illustration 11 g00781466
6/13
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 14. Remove retaining ring (18).
15. Remove carrier assembly (19).
Illustration 12 g00879368
16. Disassemble carrier assembly (19), as follows.
a. Drive spring pin (20) into planetary shaft (21) with a hammer and a punch.
Illustration 13 g00781476
b. Remove planetary shaft (21).
c. Remove spring pin (20) from planetary shaft (21) with a hammer and a punch.
7/13
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 14 g00781516
d. Remove thrust washers (22) and planetary gear (24) from the carrier assembly.
e. Remove bearing (23) from planetary gear (24).
17. Repeat Steps 16.a through 16.e for the other two planetary.
Illustration 15 g00781529
18. Remove gear (25). Remove spacer (26).
Illustration 16 g00781559
19. Remove carrier assembly (27).
20. Use two people to remove carrier assembly (27). The weight of the carrier assembly is
approximately 38 kg (85 lb).
21. Disassemble carrier assembly (27), as follows.
8/13
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 17 g00781719
a. Drive spring pin (29) into planetary shaft (28) with a hammer and a punch.
Illustration 18 g00781601
b. Remove planetary shaft (28).
c. Remove spring pin (29) from planetary shaft (28) with a hammer and a punch.
Illustration 19 g00781607
d. Remove thrust washers (30) and planetary gear (32) from the carrier assembly.
e. Remove two bearings (31) from the planetary gear.
9/13
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(SE...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 22. Repeat Steps 21.a through 21.e for the other two planetary gears.
Illustration 20 g00781730
23. Use two people to remove gear (33). The weight of gear is approximately 41 kg (90 lb).
Illustration 21 g00781807
24. Remove O-ring seal (34).
Illustration 22 g01147650
25. Remove bolts (35A) and plates (35B).
10/13
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Illustration 23 g01147651
26. Use Tooling (G) to remove dowel (37) from stopper plate (35).
Illustration 24 g01147759
27. Secure Tooling (D) to stopper plate (35). Use Tooling (D) to remove stopper plate (35).
Illustration 25 g01147930
28. Use Tooling (E) and a suitable lifting device to remove housing (36). The weight of housing
(36) is approximately 100 kg (220 lb).
11/13
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 26 g01147951
29. Remove Duo-Cone seal (39A) from housing (38).
Illustration 27 g01147975
Illustration 28 g01147934
30. Remove Duo-Cone seal (39B) from housing (36).
31. Use Tooling (F) in order to remove bearings (40) and (41) from housing (36).
32. If necessary, remove the final drive sprocket from the sprocket housing. Refer to
Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
12/13
324D L & LN Excavator EJC00001-UP (MACHINE) POWERED BY C-7 Engine(...
2020/7/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...