This document provides instructions for disassembling and assembling the final drive of an excavator model 323F SA. It outlines 32 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then outlines 13 steps for reassembling the final drive, which includes pressing bearings into the housing, measuring clearances to determine the correct shim thickness, and reinstalling removed components in reverse order. Precise assembly is needed to properly preload the bearings.
Caterpillar Cat 329D L Excavator (Prefix CZF) Service Repair Manual Instant D...yin9niaojiao
The document provides instructions for disassembling an excavator final drive transmission. It begins by removing the final drive from the excavator and securing it to a repair stand. Various components are then removed in the following order: cover, gears, carrier assembly, planetary gears, ring gear, and coupling gear. Cleanliness is emphasized and tools/lifting devices are specified. The process involves over 30 individual steps.
Caterpillar Cat 329D L Excavator (Prefix CZF) Service Repair Manual Instant D...shibi1322
The document provides instructions for disassembling an excavator final drive transmission. It involves removing over 30 individual parts in a specific sequence, starting with removing the final drive from the machine and securing it to a repair stand. Key steps include removing the transmission cover, carrier assemblies, planetary gears, and separating the main housing from the motor housing. Cleanliness is emphasized and special tools are required to remove several components due to their weight.
Caterpillar Cat 329D L Excavator (Prefix CZF) Service Repair Manual Instant D...8foskkdjdkdm3e
The document provides instructions for servicing the transmission of a 329D L Excavator. It begins by having the technician remove the final drive by referring to another section of the manual. It then lists 33 steps to fully disassemble the transmission components, identifying required tools and cautioning to mark parts for reinstallation. Key steps include removing the cover, carrier assembly, planetary gears, and separating housing components, weighing parts to assist with lifting. Thorough cleaning is stressed before disassembly to prevent dirt intrusion.
Caterpillar Cat 329D L Excavator (Prefix CZF) Service Repair Manual Instant D...jkdkkdsmmd
The document provides instructions for disassembling a final drive transmission. It begins by removing the final drive from the excavator and securing it to a repair stand. Various components are then removed in sequential order, including the cover, gears, carrier assembly, planetary gears, and seals. Cleanliness is emphasized throughout the process to prevent dirt from entering the mechanism. Over 30 individual steps are outlined with descriptions and illustrations.
Caterpillar cat 329 d l excavator (prefix czf) service repair manual (czf0000...ufjskefsmekm
The document provides instructions for disassembling a final drive assembly. It involves removing 33 parts in 23 steps, including removing the cover, gears, carrier assembly, planetary carrier, and seals. Cleanliness is important to prevent dirt from entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and eyebolts to lift components by weight.
Caterpillar cat 329 d l excavator (prefix czf) service repair manual (czf0000...fjjskekdmem
The document provides instructions for disassembling a final drive assembly. It involves removing 33 parts in 23 steps, including removing the cover, gears, carrier assembly, planetary carrier, and seals. Cleanliness is important to prevent dirt from entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and eyebolts to lift components by weight.
This document provides instructions for disassembling and assembling the final drive of a 319D Excavator. It lists 33 steps for disassembly, which include removing covers, plates, gears, seals, and housing pieces. It also lists 29 steps for assembly, which include pressing bearings into place, measuring clearances, installing seals, pins, gears, and housing pieces in the reverse order of disassembly. Precautions are provided regarding cleanliness and applying lubricants to ensure proper operation of the reassembled final drive.
This document provides instructions for disassembling and assembling the final drive of a 319D Excavator. It details 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. It then details 13 steps for assembly, including pressing in bearings, installing seals with a special tool, and applying sealant between components. Proper cleaning and use of new parts is emphasized throughout.
Caterpillar Cat 329D L Excavator (Prefix CZF) Service Repair Manual Instant D...yin9niaojiao
The document provides instructions for disassembling an excavator final drive transmission. It begins by removing the final drive from the excavator and securing it to a repair stand. Various components are then removed in the following order: cover, gears, carrier assembly, planetary gears, ring gear, and coupling gear. Cleanliness is emphasized and tools/lifting devices are specified. The process involves over 30 individual steps.
Caterpillar Cat 329D L Excavator (Prefix CZF) Service Repair Manual Instant D...shibi1322
The document provides instructions for disassembling an excavator final drive transmission. It involves removing over 30 individual parts in a specific sequence, starting with removing the final drive from the machine and securing it to a repair stand. Key steps include removing the transmission cover, carrier assemblies, planetary gears, and separating the main housing from the motor housing. Cleanliness is emphasized and special tools are required to remove several components due to their weight.
Caterpillar Cat 329D L Excavator (Prefix CZF) Service Repair Manual Instant D...8foskkdjdkdm3e
The document provides instructions for servicing the transmission of a 329D L Excavator. It begins by having the technician remove the final drive by referring to another section of the manual. It then lists 33 steps to fully disassemble the transmission components, identifying required tools and cautioning to mark parts for reinstallation. Key steps include removing the cover, carrier assembly, planetary gears, and separating housing components, weighing parts to assist with lifting. Thorough cleaning is stressed before disassembly to prevent dirt intrusion.
Caterpillar Cat 329D L Excavator (Prefix CZF) Service Repair Manual Instant D...jkdkkdsmmd
The document provides instructions for disassembling a final drive transmission. It begins by removing the final drive from the excavator and securing it to a repair stand. Various components are then removed in sequential order, including the cover, gears, carrier assembly, planetary gears, and seals. Cleanliness is emphasized throughout the process to prevent dirt from entering the mechanism. Over 30 individual steps are outlined with descriptions and illustrations.
Caterpillar cat 329 d l excavator (prefix czf) service repair manual (czf0000...ufjskefsmekm
The document provides instructions for disassembling a final drive assembly. It involves removing 33 parts in 23 steps, including removing the cover, gears, carrier assembly, planetary carrier, and seals. Cleanliness is important to prevent dirt from entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and eyebolts to lift components by weight.
Caterpillar cat 329 d l excavator (prefix czf) service repair manual (czf0000...fjjskekdmem
The document provides instructions for disassembling a final drive assembly. It involves removing 33 parts in 23 steps, including removing the cover, gears, carrier assembly, planetary carrier, and seals. Cleanliness is important to prevent dirt from entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and eyebolts to lift components by weight.
This document provides instructions for disassembling and assembling the final drive of a 319D Excavator. It lists 33 steps for disassembly, which include removing covers, plates, gears, seals, and housing pieces. It also lists 29 steps for assembly, which include pressing bearings into place, measuring clearances, installing seals, pins, gears, and housing pieces in the reverse order of disassembly. Precautions are provided regarding cleanliness and applying lubricants to ensure proper operation of the reassembled final drive.
This document provides instructions for disassembling and assembling the final drive of a 319D Excavator. It details 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. It then details 13 steps for assembly, including pressing in bearings, installing seals with a special tool, and applying sealant between components. Proper cleaning and use of new parts is emphasized throughout.
This document provides instructions for disassembling and assembling the final drive of a 319D Excavator. It lists 33 steps for disassembly, which include removing covers, plates, gears, seals, and housing pieces. It also lists 29 steps for assembly, which include pressing bearings into place, measuring clearances, installing seals, pins, gears, and housing pieces in the reverse order of disassembly. Precautions are provided regarding cleanliness and applying lubricants to ensure proper operation of the reassembled final drive.
This document provides instructions for disassembling and assembling the final drive of a 319D Excavator. It lists 33 steps for disassembly, which include removing covers, plates, gears, seals, and housing pieces. It also lists 13 steps for assembly, which include pressing bearings into place, measuring clearances, installing seals, pins, and gears, and using shims to set proper bearing preload. Cleanliness and applying lubricant to parts are emphasized throughout.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual (WZS00001...tingrm81805
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, housings and other parts. Precise steps are outlined for disassembly, and specifications and procedures are provided for reassembling each component in the proper order and with the correct tools, fasteners, seals and other materials. Torque specifications and application of sealants are noted throughout.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual (WZS00001...fujskemdidk8u
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, and housings. Tools and specifications required for assembly are also listed, with an emphasis on applying sealants, lubricants and torque specifications to reassemble components properly.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual (WZS00001...nkog14651119
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, housings and other parts. Precise steps are outlined for disassembly, and specifications and procedures are provided for reassembling each component in the proper order and with the correct tools, fasteners, seals and other materials. Torque specifications and application of sealants are noted throughout.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual Instant D...yu5676962
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, housings and other parts. Precise steps are outlined for disassembly, and specifications and procedures are provided for reassembling each component in the proper order and with the correct tools, fasteners, seals and other materials. Torque specifications and application of sealants are noted throughout.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, and housings. Precise steps are outlined for disassembling the carrier assemblies, separating the ring gears, and removing other parts from the main housing. Specifications and required tools are also provided to ensure proper reassembly of the final drive.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual (WZS00001...fujjsekmdm3ed
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, housings and other parts. Precise steps are outlined for disassembly, and specifications and procedures are provided for reassembling each component in the proper order and with the correct tools, fasteners, seals and other materials. Torque specifications and application of sealants are noted throughout.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual Instant D...f8usejkdmmd8i
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, and housings. Tools and specifications required for assembly are also listed, with an emphasis on applying sealants, lubricants and torque specifications to reassemble components properly.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual Instant D...tengtui535
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, housings and other parts. Precise steps are outlined for disassembly, and specifications and procedures are provided for reassembling each component in the proper order and with the correct tools, fasteners, seals and other materials. Torque specifications and application of sealants are noted throughout.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual Instant D...f8seodkdmdmed3
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, and housings. Tools and specifications required for assembly are also listed, including torque specifications and types of sealant to apply between mating parts.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual (WZS00001...hdjsjndndnd
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, and housings. Instructions are provided with illustrations and include precautions for lifting heavy parts and applying sealants. Torque specifications and part numbers are listed for reassembly.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual Instant D...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, and housings. Instructions are provided with illustrations and include precautions for lifting heavy parts and applying sealants. Torque specifications and part numbers are listed for reassembly.
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. The disassembly process involves removing 28 individual parts and components from the final drive and related assemblies using various tools. The assembly process reverses the disassembly steps and requires aligning identification marks to ensure correct positioning of parts.
This document provides disassembly and assembly instructions for the final drive of a 345D excavator. It details 30 steps to disassemble the final drive components including removing the final drive cover, carrier assemblies, ring gear, and other parts. It then lists 21 steps to reassemble the final drive, applying anti-seize compound to bearings, installing bearing cups and cones, and refitting the various components removed during disassembly. The document includes detailed illustrations and references other service manuals for additional information.
This document provides disassembly and assembly instructions for the final drive of a 345D excavator. It details 30 steps to disassemble the final drive components including removing the final drive cover, carrier assemblies, ring gear, and other parts. It then lists 21 steps for reassembling the final drive, including pressing in bearing cups, installing bearing cones and inner races, and attaching the sprocket housing using lifting devices. Tools required include retaining ring pliers, eyebolts, and a transmission repair stand.
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. It begins with removing the final drive and describes dismantling it into individual parts like the ring gear, carrier assemblies, planetary gears and shafts. Alignment marks are noted to aid reassembly. The instructions then describe assembling the final drive components back into the final drive housing.
Caterpillar cat 345 d excavator (prefix neg) service repair manual (neg00001 ...fios9dkksd
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. It begins with removing the final drive and associated parts like the cover, ring gear, carrier assemblies, and sprocket housing. It then describes disassembling each of these components and their internal parts. The assembly section provides the reverse steps for reassembling the final drive.
This document provides disassembly and assembly instructions for the final drive of a 345D excavator. It details 30 steps to disassemble the final drive components including removing the ring gear, carrier assemblies, planetary gears, and sprocket housing. It then lists 21 steps to reassemble the final drive, including pressing in new bearing cups, installing bearing cones and inner races, and attaching the sprocket housing using lifting devices. Tools required include retaining ring pliers, eyebolts, and a transmission repair stand.
This document provides disassembly and assembly instructions for the final drive of a 345D excavator. It details 30 steps to disassemble the final drive components including removing the final drive cover, carrier assemblies, ring gear, and other parts. It then lists 21 steps to reassemble the final drive, applying anti-seize compound to bearings, installing bearing cups and cones, and refitting the various components removed during disassembly. The document includes detailed illustrations and references other manuals for additional information.
Caterpillar Cat 336E H and 336E LH EXCAVATOR (Prefix JEA) Service Repair Manu...f89siekkmdmm2w
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps to disassemble the motor, removing components like the head, springs, brake piston, and bearing races. It then lists 28 steps for reassembling the motor, describing how to install seals, plates, springs and other parts in the reverse order of disassembly. Precautions are included to properly release spring forces and avoid damaging mating surfaces. Tools required include an eyebolt, retaining ring pliers, bearing puller, and adapter to securely hold parts during disassembly and assembly.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix PPN) Service Repair Manu...f89siekkmdmm2w
1. The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators.
2. The disassembly procedure includes using various tools to remove over 30 individual parts from the pump in the correct order.
3. Reassembly requires carefully installing each part in the reverse order, ensuring proper placement and installation of seals, bearings, springs and other components.
4. Cleanliness is emphasized as important during both disassembly and assembly to prevent dirt from damaging internal parts.
More Related Content
Similar to Caterpillar Cat 323F SA and 323F LN Excavator (Prefix FA2) Service Repair Manual Instant Download.pdf
This document provides instructions for disassembling and assembling the final drive of a 319D Excavator. It lists 33 steps for disassembly, which include removing covers, plates, gears, seals, and housing pieces. It also lists 29 steps for assembly, which include pressing bearings into place, measuring clearances, installing seals, pins, gears, and housing pieces in the reverse order of disassembly. Precautions are provided regarding cleanliness and applying lubricants to ensure proper operation of the reassembled final drive.
This document provides instructions for disassembling and assembling the final drive of a 319D Excavator. It lists 33 steps for disassembly, which include removing covers, plates, gears, seals, and housing pieces. It also lists 13 steps for assembly, which include pressing bearings into place, measuring clearances, installing seals, pins, and gears, and using shims to set proper bearing preload. Cleanliness and applying lubricant to parts are emphasized throughout.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual (WZS00001...tingrm81805
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, housings and other parts. Precise steps are outlined for disassembly, and specifications and procedures are provided for reassembling each component in the proper order and with the correct tools, fasteners, seals and other materials. Torque specifications and application of sealants are noted throughout.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual (WZS00001...fujskemdidk8u
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, and housings. Tools and specifications required for assembly are also listed, with an emphasis on applying sealants, lubricants and torque specifications to reassemble components properly.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual (WZS00001...nkog14651119
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, housings and other parts. Precise steps are outlined for disassembly, and specifications and procedures are provided for reassembling each component in the proper order and with the correct tools, fasteners, seals and other materials. Torque specifications and application of sealants are noted throughout.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual Instant D...yu5676962
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, housings and other parts. Precise steps are outlined for disassembly, and specifications and procedures are provided for reassembling each component in the proper order and with the correct tools, fasteners, seals and other materials. Torque specifications and application of sealants are noted throughout.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual Instant D...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, and housings. Precise steps are outlined for disassembling the carrier assemblies, separating the ring gears, and removing other parts from the main housing. Specifications and required tools are also provided to ensure proper reassembly of the final drive.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual (WZS00001...fujjsekmdm3ed
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, housings and other parts. Precise steps are outlined for disassembly, and specifications and procedures are provided for reassembling each component in the proper order and with the correct tools, fasteners, seals and other materials. Torque specifications and application of sealants are noted throughout.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual Instant D...f8usejkdmmd8i
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, and housings. Tools and specifications required for assembly are also listed, with an emphasis on applying sealants, lubricants and torque specifications to reassemble components properly.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual Instant D...tengtui535
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, housings and other parts. Precise steps are outlined for disassembly, and specifications and procedures are provided for reassembling each component in the proper order and with the correct tools, fasteners, seals and other materials. Torque specifications and application of sealants are noted throughout.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual Instant D...f8seodkdmdmed3
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, and housings. Tools and specifications required for assembly are also listed, including torque specifications and types of sealant to apply between mating parts.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual (WZS00001...hdjsjndndnd
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, and housings. Instructions are provided with illustrations and include precautions for lifting heavy parts and applying sealants. Torque specifications and part numbers are listed for reassembly.
Caterpillar Cat 318E L Excavator (Prefix WZS) Service Repair Manual Instant D...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318E L excavator. It describes in detail how to remove over 30 individual components of the final drive including gears, shafts, seals, and housings. Instructions are provided with illustrations and include precautions for lifting heavy parts and applying sealants. Torque specifications and part numbers are listed for reassembly.
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. The disassembly process involves removing 28 individual parts and components from the final drive and related assemblies using various tools. The assembly process reverses the disassembly steps and requires aligning identification marks to ensure correct positioning of parts.
This document provides disassembly and assembly instructions for the final drive of a 345D excavator. It details 30 steps to disassemble the final drive components including removing the final drive cover, carrier assemblies, ring gear, and other parts. It then lists 21 steps to reassemble the final drive, applying anti-seize compound to bearings, installing bearing cups and cones, and refitting the various components removed during disassembly. The document includes detailed illustrations and references other service manuals for additional information.
This document provides disassembly and assembly instructions for the final drive of a 345D excavator. It details 30 steps to disassemble the final drive components including removing the final drive cover, carrier assemblies, ring gear, and other parts. It then lists 21 steps for reassembling the final drive, including pressing in bearing cups, installing bearing cones and inner races, and attaching the sprocket housing using lifting devices. Tools required include retaining ring pliers, eyebolts, and a transmission repair stand.
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. It begins with removing the final drive and describes dismantling it into individual parts like the ring gear, carrier assemblies, planetary gears and shafts. Alignment marks are noted to aid reassembly. The instructions then describe assembling the final drive components back into the final drive housing.
Caterpillar cat 345 d excavator (prefix neg) service repair manual (neg00001 ...fios9dkksd
This document provides step-by-step instructions for disassembling and assembling the final drive components of a 345D Excavator. It begins with removing the final drive and associated parts like the cover, ring gear, carrier assemblies, and sprocket housing. It then describes disassembling each of these components and their internal parts. The assembly section provides the reverse steps for reassembling the final drive.
This document provides disassembly and assembly instructions for the final drive of a 345D excavator. It details 30 steps to disassemble the final drive components including removing the ring gear, carrier assemblies, planetary gears, and sprocket housing. It then lists 21 steps to reassemble the final drive, including pressing in new bearing cups, installing bearing cones and inner races, and attaching the sprocket housing using lifting devices. Tools required include retaining ring pliers, eyebolts, and a transmission repair stand.
This document provides disassembly and assembly instructions for the final drive of a 345D excavator. It details 30 steps to disassemble the final drive components including removing the final drive cover, carrier assemblies, ring gear, and other parts. It then lists 21 steps to reassemble the final drive, applying anti-seize compound to bearings, installing bearing cups and cones, and refitting the various components removed during disassembly. The document includes detailed illustrations and references other manuals for additional information.
Similar to Caterpillar Cat 323F SA and 323F LN Excavator (Prefix FA2) Service Repair Manual Instant Download.pdf (20)
Caterpillar Cat 336E H and 336E LH EXCAVATOR (Prefix JEA) Service Repair Manu...f89siekkmdmm2w
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps to disassemble the motor, removing components like the head, springs, brake piston, and bearing races. It then lists 28 steps for reassembling the motor, describing how to install seals, plates, springs and other parts in the reverse order of disassembly. Precautions are included to properly release spring forces and avoid damaging mating surfaces. Tools required include an eyebolt, retaining ring pliers, bearing puller, and adapter to securely hold parts during disassembly and assembly.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix PPN) Service Repair Manu...f89siekkmdmm2w
1. The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators.
2. The disassembly procedure includes using various tools to remove over 30 individual parts from the pump in the correct order.
3. Reassembly requires carefully installing each part in the reverse order, ensuring proper placement and installation of seals, bearings, springs and other components.
4. Cleanliness is emphasized as important during both disassembly and assembly to prevent dirt from damaging internal parts.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix MFA) Service Repair ...f89siekkmdmm2w
This document provides instructions for disassembling the travel motor on 336D2 XE and 336D2 LXE excavator models. It outlines 27 steps to remove parts like the motor head assembly, springs, pistons, seals, plates and other components. Various tools are required including bolts, retaining ring pliers, drivers and pullers. Precautions are mentioned to relieve spring pressure safely and contain fluids. The process yields individual parts to allow inspection and replacement of worn items.
The document provides instructions for removing and installing a cab on a 336 excavator. It lists required tools including eyebolts. Steps include removing the air cleaner mount first. Various illustrations show disconnecting wiring harnesses and brackets, and lifting the cab off using the eyebolts. Reinstallation follows the removal steps in reverse order.
The document provides instructions for disassembling and assembling the final drive of a 336 Excavator. It lists 24 steps for disassembly, removing components like gears, shafts, seals and housings. It then lists 29 steps for assembly, installing components in reverse order and noting specifics like torque values and tooling used. Precise assembly is emphasized, including bearing installation and shim thickness measurement to set proper backlash.
The document provides instructions for removing and installing various engine components on a Caterpillar 336 Excavator including the lifter group, camshaft, camshaft gear, camshaft bearings, and engine oil pan. The instructions include lists of required tools and multi-step procedures accompanied by illustrations of each step. Safety notices are also provided throughout the document.
Caterpillar Cat 336D and 336D L Excavator (Prefix M3N) Service Repair Manual ...f89siekkmdmm2w
This document provides instructions for removing the swing gear and bearing from an excavator undercarriage frame. The procedure involves removing all grease, marking the swing gear and bearing and frame for alignment, attaching lifting tools, and using a hydraulic torque wrench to remove bolts and spacers. The swing gear and bearing assembly weighs approximately 280 kg and must be lifted carefully after the bolts are removed.
Caterpillar Cat 335F and 335F L Excavator (Prefix SGJ) Service Repair Manual ...f89siekkmdmm2w
This document provides instructions for disassembling and assembling the travel motor on a 335F excavator model. The disassembly process involves removing 27 different components from the travel motor in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on lubricating parts and tightening bolts to the correct torque specifications.
The document provides instructions for removing and installing components on a 336 excavator, including the operator monitor, hydraulic lockout control, and piston motor. It lists the required tools and includes illustrations showing the component locations and step-by-step removal and installation procedures. Safety warnings are provided to prevent injury when working with spring loaded parts. The document also identifies the excavator model and powered engine to ensure the correct repair manual is referenced.
The document is a service repair manual that provides instructions for connecting and disconnecting various components of an excavator model 336. It includes:
1) A list of required tools and replacement parts for the procedures.
2) Step-by-step illustrated instructions for connecting components like the hydraulic pump, boom cylinder, and undercarriage frame.
3) Directions for draining fluids like oil from the final drive before disconnecting it.
4) Notes on installation being the reverse of removal steps and requirements like torquing nuts to specification.
Caterpillar Cat 330F and 330F LN Excavator (Prefix HBT) Service Repair Manual...f89siekkmdmm2w
This document provides instructions for removing and installing components related to the crankshaft and front cover of a Caterpillar 330F excavator engine. The procedures include removing and installing the crankshaft pulley, vibration damper, front seal, and heavy duty front cover. Tools required are listed for each procedure. Illustrations show the components and steps to disassemble and reassemble the assemblies.
Caterpillar Cat 330D2 and 330D2 L Excavator (Prefix FEX) Service Repair Manua...f89siekkmdmm2w
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps including removing the final drive cover, carrier assembly, planetary gears, ring gears, and other components. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components weighing up to 550 kg during disassembly. Cleanliness is important to prevent dirt from entering internal mechanisms.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Installation requires matching dimensions and orientations when pressing in new bearings and reinstalling components.
To remove the flywheel, bolts are first removed 180 degrees apart using a guide stud before lifting the flywheel off. Installation involves heating and pressing in a ring gear, lifting the flywheel into place using guide studs, and torquing bolts to the specified value
Caterpillar Cat 330D L Excavator (Prefix JLP) Service Repair Manual Instant D...f89siekkmdmm2w
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts before disassembly and have additional assistance when removing heavier parts weighing over 30 kg. The detailed process takes the final drive completely apart down to individual planetary gears and shafts.
This document provides installation instructions for a main hydraulic pump on a 330D excavator. It lists 54 steps to assemble components like pistons, gears, brackets, hoses and sensors. Tools include lever pullers, link brackets and torque wrenches. Precautions are given for spring loaded parts. The process involves lifting heavy pump assemblies into place and tightening hundreds of bolts and fittings to specified torques.
Caterpillar Cat 330D L Excavator (Prefix LRM) Service Repair Manual Instant D...f89siekkmdmm2w
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It describes disconnecting hydraulic lines and removing mounting bolts, covers, and seals. Special tools are required to safely lift the heavy parts and create a vacuum in the hydraulic system. Proper cleaning, containment of fluids, and use of anti-seize coating are emphasized to prevent contamination.
Caterpillar Cat 330D and 330D L Excavator (Prefix NBD) Service Repair Manual ...f89siekkmdmm2w
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing individual parts like springs pins, washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar Cat 330D and 330D L Excavator (Prefix EDX) Service Repair Manual ...f89siekkmdmm2w
The document provides instructions for assembling and installing the swing drive of an excavator. It describes 30 steps for assembling the internal components of the swing drive, including installing bearings, gears, seals, and housing components. It then describes 6 steps for installing the entire assembled swing drive into the excavator frame, including attaching lifting brackets, applying sealant, tightening bolts to the specified torque, and filling it with oil. The overall process installs and secures the fully assembled swing drive subsystem into the excavator.
Caterpillar Cat 330C L Excavator (Prefix CYA) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for disassembling and assembling the travel motor of a 330C L excavator. It lists the required tools and presents step-by-step procedures for removing and installing each component of the travel motor. Some key steps include removing the head from the motor body, taking apart the rotating assembly, and disassembling the brake piston. Special care must be taken to avoid damaging parts and ensure proper alignment during reassembly.
Caterpillar Cat 330D and 330D L Excavator (Prefix GBC) Service Repair Manual ...f89siekkmdmm2w
This document provides instructions for removing and installing components in the cylinder head of a Caterpillar C9 engine, including the rocker arm shaft, cylinder head, lifter group, and camshaft. The procedures describe draining coolant, removing mounting bolts and connections, and lifting components out of the engine. Torque specifications and the proper sequence for installing mounting bolts are also included.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323F SA EXCAVATOR FA2
Configuration: 323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
320F, 323F Excavators Machine Systems
Media Number -M0066628-06 Publication Date -01/09/2018 Date Updated -18/09/2018
i06226012
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 154-6181 Forcing Bolt 1
D 138-7574 Link Bracket 2
E
5F-7366 Forcing Bolt 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F 1U-8846 Gasket Sealant 1
Start By:
a. Remove the final drive.
1/10
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
2/10
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00708091
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
Illustration 4 g00708235
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
Illustration 5 g00708092
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
3/10
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g01304883
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 7 g00708144
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
Illustration 8 g00708218
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
4/10
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
Illustration 9 g00708162
13. Remove sun gear (14) from carrier assembly (15).
Illustration 10 g00708325
14. Remove spacer (16).
Illustration 11 g00708184
5/10
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
Illustration 12 g00708360
16. Use a screwdriver or a chisel in order to separate the two ring gears (17).
Note: The two ring gears are held together with Tooling (F). It may be necessary to heat the
ring gears in order to soften the sealant. Do not heat over 135 °C (275 °F) for more than
thirty minutes.
Illustration 13 g00708172
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
6/10
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00708175
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
Illustration 15 g00708370
Illustration 16 g00708220
b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
7/10
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
Illustration 17 g00708186
22. Remove O-ring seal (24) from main housing (18).
Illustration 18 g00708187
23. Remove bolts (25) from gear (26).
Illustration 19 g00708202
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
8/10
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Note: The motor housing will separate from the main housing (18) once gear (26) is
removed. Make sure that the motor housing is supported.
Illustration 20 g00708211
25. Remove shims (27) from the main housing.
Illustration 21 g00708212
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from the motor housing (28). The combined weight of main housing (18) and the
final drive sprocket is approximately 82 kg (180 lb).
9/10
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 22 g00708214
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
Illustration 23 g00708215
Illustration 24 g00708216
30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 7 22:36:16 UTC+0800 2020
10/10
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M00...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323F SA EXCAVATOR FA2
Configuration: 323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
320F, 323F Excavators Machine Systems
Media Number -M0066628-06 Publication Date -01/09/2018 Date Updated -18/09/2018
i06226016
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
D 138-7574 Link Bracket 2
G 126-3994 Duo-Cone Seal Installer 1
H 5P-3931 Anti-Seize Compound
F 1U-8846 Gasket Sealant
Note: Apply a light film of hydraulic oil to all components before assembly.
1. Install the final drive sprocket if the sprocket was removed from the main housing.
2. Remove the final drive sprocket.
1/13
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g00708215
3. Apply Tooling (H) to the outer diameter of the bearings.
4. Install bearings (32) and (33) in main housing (18) with a suitable press.
5. Make sure that bearing (32) and bearing (33) contact the counterbore in the main housing.
6. Use the following procedure to preload the bearings and determine the correct thickness of
shims.
Illustration 2 g00713058
a. Fasten Tooling (D) and a suitable lifting device to main housing (18). Install the main
housing on the motor housing.
b. Put the main housing and the motor housing in a suitable press.
2/13
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g00709278
(a) Bearing surface
(b) Housing surface
c. Use a suitable press and a spacer in order to apply a load of 4000 kg (8819 lb) on the
bearings. Rotate the housing in order to seat the bearings.
d. Reduce the load on the bearings to 1000 ± 100 kg (2205 ± 221 lb).
e. Use a depth micrometer in order to measure the step length between the bearing
surface and the housing surface. Take measurements at several different locations
around the housing. Compute the average of the measured dimensions and record the
number. Call this Dimension (Y).
Illustration 4 g00709276
f. Use a depth micrometer in order to measure the step length of the coupling gear (26).
Take measurements at several different locations around the gear. Compute the
average of the measured dimensions and record the number. Call this Dimension (X).
g. The thickness of the shims is equal to (X − Y) ± 0.05 mm (0.002 inch).
Note: Use no more than two shims. If two shims are required, install the thinner shim
next to the gear.
h. Remove the main housing from the motor housing.
3/13
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 5 g01021370
7. Use Tooling (G) in order to install Duo-Cone seal (31) in main housing (18). Refer to
Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contact the seals must be clean and dry. After
installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal seals.
Illustration 6 g01021371
8. Use Tooling (G) in order to install Duo-Cone seal (29) in motor housing (28).
Illustration 7 g00708214
4/13
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 9. Apply Tooling (H) to the surfaces that contact pins (30).
10. Install alignment pins (30).
Note: Do not damage the Duo-Cone seals in the main housing or in the motor housing
during the assembly of the two components. After installation of the main housing on the
motor housing, there will be a small gap between the components. The gap is caused by the
Duo-Cone seals. This gap will be eliminated during installation of gear (26).
Illustration 8 g00713058
11. Fasten Tooling (D) and a suitable lifting device to main housing (18). Install the main
housing on the motor housing.
Illustration 9 g00708211
12. Install shims (27) that were determined in Step 6.g in the main housing.
Note: If two shims are required, install the thinner shim next to the gear.
5/13
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 10 g00708187
13. Install gear (26).
14. Install bolts (25) in gear (26). Install the bolts in an even pattern until the gear is seated
against the bearing. Tighten bolts (25) in a crisscross pattern.
Illustration 11 g00708186
15. Install O-ring seal (24) to main housing (18).
Illustration 12 g00708175
16. Assemble carrier assembly (15), as follows.
6/13
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 13 g00708220
a. Install bearings (22) in planetary gear (23).
b. Install thrust washers (21) and planetary gear (23) in the carrier assembly.
c. Use a deburring tool in order to remove the metal burr from the openings in the
carrier. Install planetary shaft (19) in the carrier assembly.
d. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
Illustration 14 g00513451
e. Orient the split in spring pin (20) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.50 mm (0.059 inch) from
the outside diameter of the spring pin hole.
17. Repeat Steps 16.a through 16.e in order to install the remaining planetary gears in the carrier
assembly.
7/13
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 15 g00708172
18. Install a lifting sling through the middle of carrier assembly (15). Fasten a 12.7 mm
(0.50 inch) shackle to the suitable lifting device.
19. Install carrier assembly (15) on the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Remove the shackle and the suitable lifting device.
Illustration 16 g00713148
21. Apply Tooling (F) to the mating surface of ring gear (17b).
22. Install ring gear (17a) on ring gear (17b).
8/13
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 17 g00708184
23. Fasten a suitable lifting device to ring gears (17), as shown. Install the ring gears to main
housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
Illustration 18 g00708325
24. Install spacer (16) in the carrier assembly.
Illustration 19 g00708162
25. Install sun gear (14) in carrier assembly (15).
9/13
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 20 g01304883
Illustration 21 g00708218
26. Assemble carrier assembly (7), as follows.
a. Install bearing (12) in planetary gear (13).
b. Install thrust washers (11) and planetary gear (13) in the carrier assembly.
c. Install planetary shaft (9) in the carrier assembly.
d. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 22 g00513451
e. Orient the split in spring pin (10) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.50 mm (0.059 inch) from
the outside diameter of the spring pin hole.
10/13
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M00...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 27. Repeat Steps 26.a through 26.e in order to install the remaining planetary gears in the carrier
assembly.
Illustration 23 g00708092
28. Install carrier assembly (7) in the ring gear. The weight of carrier assembly (7) is
approximately 14 kg (30 lb).
29. Install sun gear (8) in carrier assembly (7).
30. Install spacer (6) in carrier assembly (7).
Illustration 24 g00708235
31. Install new O-ring seals (5) on plugs (4) that were in the cover.
11/13
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M00...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 25 g00708091
32. Install plugs (4) in cover (2). Tighten plugs (4) to a torque of 80 ± 10 N·m (59 ± 7 lb ft).
33. Install thrust plate (3) in cover (2).
34. Apply Tooling (F) to the mating surface of the ring gear.
Illustration 26 g00708090
35. Fasten Tooling (B) and a suitable lifting device to cover (2), as shown. The weight of cover
(2) is approximately 32 kg (70 lb). Install cover (2).
36. Remove Tooling (B). Install the setscrews in cover (2).
Illustration 27 g00708089
37. Install bolts (1) and the washers that hold the cover in position. Tighten bolts (1) in a
crisscross pattern.
38. Remove the final drive from Tooling (A). The combined weight of the final drive and final
drive sprocket is approximately 310 kg (683 lb).
End By:
a. Install the final drive.
12/13
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M00...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323F SA EXCAVATOR FA2
Configuration: 323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
320F, 323F Excavators Machine Systems
Media Number -M0066628-06 Publication Date -01/09/2018 Date Updated -18/09/2018
i07240392
Final Drive and Travel Motor - Remove and Install
SMCS - 4050; 4351
S/N - FA21-UP
S/N - MFY1-UP
S/N - NHD1-UP
S/N - REW1-UP
S/N - YBM1-UP
S/N - YEC1-UP
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439–3939 Link Bracket As 1
B - Loctite C5A Copper Anti-Seize -
Start By:
a. Separate the track.
1. Drain the oil from the final drive.
1/3
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g02708415
2. Remove bolts (1) and cover (2).
Illustration 2 g02708757
3. Remove six bolts (3). Relocate the counterbalance valve.
Illustration 3 g02708761
2/3
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 4 g02708759
4. Attach Tooling (A) and a suitable lifting device to final drive (4). The weight of final drive
(4) is approximately 312 kg (688 lb).
5. Disconnect hose assemblies (5). Remove bolts (6) and remove final drive (4).
Installation Procedure
1. Install final drive (4) in the reverse order of removal.
a. Before assembly, remove compound, oil, and dust from female threads, then apply
Tooling (B) to the threads of bolts (6).
b. Tighten bolts (6) in an alternating sequence to a torque of 150 ± 25 N·m
(111 ± 18 lb ft). Turn an additional angle of 55 ± 5 degrees. Refer to Service
Magazine , M0083843 , "An Improved Bolt Tightening Procedure for the Critical
Joints Is Now Used on all Excavators" for more detailed information.
c. Tighten bolts (3) to a torque of 80 ± 8 N·m (59 ± 6 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 7 22:38:15 UTC+0800 2020
3/3
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323F SA EXCAVATOR FA2
Configuration: 323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
320F, 323F Excavators Machine Systems
Media Number -M0066628-06 Publication Date -01/09/2018 Date Updated -18/09/2018
i06280845
Swivel - Remove and Install
SMCS - 5060-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1
B 5P-3050 Floor Jack Gp 1
C 138-7575 Link Bracket 2
D - Loctite 242 -
E 1P-2420 Transmission Repair Stand 1
Illustration 1 g02726974
1/5
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 1. Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach
an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This
procedure will pull vacuum on the hydraulic system.
Illustration 2 g02615566
2. Attach Tooling (B) under guard (2). The weight of guard (2) is approximately 75 kg
(165 lb). Loosen bolts (1), slide bolts inward to release the locks. Remove guard (2).
Illustration 3 g02626110
3. Remove bracket (3). Remove hose assemblies (4).
Illustration 4 g02626112
2/5
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. 4. Remove hose assemblies (6). Remove fittings (5).
Illustration 5 g02615556
5. Remove hose assemblies (7), hose assemblies (8), and fittings (9) from swivel (10).
Illustration 6 g02615564
6. Remove hose assemblies and fittings (11). Remove bolts (12).
Illustration 7 g02727286
7. Attach Tooling (C) and a suitable lifting device to swivel (10). The weight of the swivel
(10) is approximately 50 kg (110 lb). Remove clamp (13), retainer (14) and boot (15).
3/5
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
32. Illustration 11 g02615562
10. Attach Tooling (C) and a suitable lifting device to the swivel and locate in Tooling (E). The
weight of swivel (10) is approximately 45 kg (100 lb). Remove rotor (18) from swivel
housing (19).
Illustration 12 g02615563
11. Remove seals (20).
Installation Procedure
1. Install swivel (10) in the reverse order of removal.
Note: Lubricate seals (20) and rotor (18) with clean hydraulic oil for assembly.
a. Apply sealant between the mating surface of swivel (10) and the undercarriage before
installing swivel (10). Apply Tooling (D) to bolts (12).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 7 22:39:14 UTC+0800 2020
5/5
323F LN Excavator FA210101-UP (MACHINE) POWERED BY C4.4 Engine(M0092...
2020/10/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...