The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3066 engine. It describes using lifting tools to remove the flywheel housing which weighs approximately 65 lbs. The procedure includes cleaning the mating surfaces, installing a new gasket, and securing the housing with bolts and washers. Tools are also used to remove the old oil seal and install a new seal and crankshaft wear sleeve.
Caterpillar cat 323 d ln excavator (prefix dkw) service repair manual (dkw000...fjjsekmsmmes
This document provides instructions for removing and installing a flywheel on a Caterpillar 3066 engine. The procedures include:
1. Removing bolts and washers to separate the flywheel housing from the cylinder block.
2. Using lifting equipment to remove the flywheel housing, which weighs approximately 65 pounds.
3. Inspecting the oil seal and replacing if needed before installing a new one along with the crankshaft wear sleeve.
4. Cleaning surfaces and installing a new gasket before reattaching the flywheel housing with bolts and washers.
Caterpillar cat 323 d s excavator (prefix dkw) service repair manual (dkw0000...fjjsekmsmmes
This document provides instructions for removing and installing a flywheel on a 323D LN and 323D S excavator. The removal procedure involves using tools to remove bolts securing the flywheel adapter, inner ring, and flywheel to the crankshaft. The flywheel and ring gear can then be lifted out. To install, the ring gear is heated and pressed onto the flywheel if removed previously. Tools are then used to lower the flywheel into place and bolts are installed to secure it to the crankshaft.
Caterpillar cat 312 b track type excavator (prefix 3fs) service repair manual...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and rings.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 312 b l excavator (prefix 2ns) service repair manual (2ns0000...fjsekksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the flywheel from the crankshaft, and using lifting tools to pull the flywheel out of the housing.
3) Reversing the process to install a new or repaired flywheel housing, making sure to tighten bolts to the specified torque and check flywheel runout.
Caterpillar cat 312 b excavator (prefix 2ns) service repair manual (2ns00001 ...fjsekksmemm
The document provides instructions for removing and installing a flywheel on a Caterpillar 312B excavator engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel out of the housing using a strap and lifting device.
3) Removing the ring gear by heating it and tapping it off.
4) Reversing the process to install a new flywheel, pressing the heated ring gear onto the flywheel if needed.
Caterpillar Cat 312B and 312B L EXCAVATOR (Prefix 2NS) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1. Removing the flywheel, inner ring, and adapter to access the flywheel housing.
2. Using lifting straps and tools to remove the flywheel housing, which weighs 50 kg.
3. Cleaning and inspecting the housing, flywheel, and related components before reinstallation. Precautions are given to prevent contamination.
Caterpillar Cat 312B and 312B L EXCAVATOR (Prefix 2NS) Service Repair Manual ...zan2736ban
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment to remove the flywheel housing and check the oil seal for wear.
2) Cleaning the mating surfaces and installing a new gasket before reinstalling the housing with bolts.
3) Installing a new oil seal and crankshaft wear sleeve using a special tool during reinstallation.
Caterpillar cat 323 d ln excavator (prefix dkw) service repair manual (dkw000...fjjsekmsmmes
This document provides instructions for removing and installing a flywheel on a Caterpillar 3066 engine. The procedures include:
1. Removing bolts and washers to separate the flywheel housing from the cylinder block.
2. Using lifting equipment to remove the flywheel housing, which weighs approximately 65 pounds.
3. Inspecting the oil seal and replacing if needed before installing a new one along with the crankshaft wear sleeve.
4. Cleaning surfaces and installing a new gasket before reattaching the flywheel housing with bolts and washers.
Caterpillar cat 323 d s excavator (prefix dkw) service repair manual (dkw0000...fjjsekmsmmes
This document provides instructions for removing and installing a flywheel on a 323D LN and 323D S excavator. The removal procedure involves using tools to remove bolts securing the flywheel adapter, inner ring, and flywheel to the crankshaft. The flywheel and ring gear can then be lifted out. To install, the ring gear is heated and pressed onto the flywheel if removed previously. Tools are then used to lower the flywheel into place and bolts are installed to secure it to the crankshaft.
Caterpillar cat 312 b track type excavator (prefix 3fs) service repair manual...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and rings.
Caterpillar cat 312 b l track type excavator (prefix 3fs) service repair manu...fjskkksmemm
This document provides instructions for removing and installing a flywheel on a Caterpillar 3064 engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel off using a strap and lifting device, as it weighs 50 kg.
3) Instructions for removing the ring gear by heating and tapping it off.
4) The installation procedure lists cleaning and applying compounds before securing the flywheel back onto the crankshaft using bolts and checking the runout.
Caterpillar cat 312 b l excavator (prefix 2ns) service repair manual (2ns0000...fjsekksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the flywheel from the crankshaft, and using lifting tools to pull the flywheel out of the housing.
3) Reversing the process to install a new or repaired flywheel housing, making sure to tighten bolts to the specified torque and check flywheel runout.
Caterpillar cat 312 b excavator (prefix 2ns) service repair manual (2ns00001 ...fjsekksmemm
The document provides instructions for removing and installing a flywheel on a Caterpillar 312B excavator engine. It describes:
1) Using various tools to remove the adapter, inner ring, and bolts securing the flywheel.
2) Lifting the flywheel out of the housing using a strap and lifting device.
3) Removing the ring gear by heating it and tapping it off.
4) Reversing the process to install a new flywheel, pressing the heated ring gear onto the flywheel if needed.
Caterpillar Cat 312B and 312B L EXCAVATOR (Prefix 2NS) Service Repair Manual ...fijsekkdmdm2w
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1. Removing the flywheel, inner ring, and adapter to access the flywheel housing.
2. Using lifting straps and tools to remove the flywheel housing, which weighs 50 kg.
3. Cleaning and inspecting the housing, flywheel, and related components before reinstallation. Precautions are given to prevent contamination.
Caterpillar Cat 312B and 312B L EXCAVATOR (Prefix 2NS) Service Repair Manual ...zan2736ban
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment to remove the flywheel housing and check the oil seal for wear.
2) Cleaning the mating surfaces and installing a new gasket before reinstalling the housing with bolts.
3) Installing a new oil seal and crankshaft wear sleeve using a special tool during reinstallation.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment to remove the flywheel housing and check the oil seal.
2) Cleaning the mating surfaces and installing a new gasket before reinstalling the housing.
3) Securing the housing with bolts and installing a new oil seal and crankshaft sleeve.
Caterpillar Cat 312B L EXCAVATOR (Prefix 2NS) Service Repair Manual (2NS00001...fusjekkdmdmd2w
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment to remove the flywheel housing and check the oil seal for wear.
2) Cleaning the mating surfaces and installing a new gasket before reinstalling the housing with bolts.
3) Installing a new oil seal and crankshaft wear sleeve with special tools during reinstallation.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing twelve bolts and the adapter to separate the housing from the flywheel.
2) Installing a new housing by positioning the adapter and securing it with twelve bolts.
3) Checking the flywheel runout after installation to ensure proper alignment.
Caterpillar Cat 312B L EXCAVATOR (Prefix 2NS) Service Repair Manual (2NS00001...f8usejkddmmd
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the adapter from the flywheel housing and remove the adapter.
2) Removing bolts to separate the inner ring from the flywheel and removing the inner ring.
3) Using lifting tools to remove the flywheel from the housing, which weighs 50kg.
4) Reversing the removal steps to install the flywheel housing, including securing the flywheel to the crankshaft with bolts and checking flywheel runout.
Caterpillar cat 312 b excavator (prefix 2ns) service repair manual (2ns00001 ...kmdddmm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment to remove the flywheel housing and check the oil seal for wear.
2) Cleaning the mating surfaces and installing a new gasket before reinstalling the housing with bolts.
3) Installing a new oil seal and crankshaft wear sleeve with special tools during reinstallation.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing the flywheel, adapter, inner ring, and bolts securing the flywheel to the crankshaft.
2) Installing the flywheel using lifting tools, bolts, and checking runout with a gauge.
3) Removing the crankshaft rear seal and wear sleeve using drilling, hammer, and distorter tools.
4) Installing a new rear seal and wear sleeve using a installer, locator, bolts, washer and compound.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual Instant D...fskekkdmdmdm3e
- The document provides instructions for removing and installing the idler gear of the front gear group on a C4.2 engine for Caterpillar built machines.
- To remove the idler gear, the front housing must first be removed. Then the idler gear bolt, thrust plate, and idler gear can be taken off the idler gear shaft. An idler shaft puller and driver group may be needed.
- To install the idler gear, first press in a new bushing if needed. Then install the idler shaft, idler gear, thrust plate, washer and idler gear bolt. Tighten the bolt to the specified torque.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly process removes components like housing, gears, seals and bearings. The 22 step assembly process reverses this to rebuild the final drive, applying loctite and torquing bolts to specification. Tools required include link brackets, crossblocks, drivers and torque wrenches. Safety precautions are noted for releasing spring forces.
Caterpillar Cat 336F and 336F L Excavator (Prefix DSW) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs and seals. Tools required include a transmission repair stand, lifting eye assembly, driver group and various bolts, pins and seals. Technicians are advised to mark components for reinstallation and take care when removing parts to avoid damage.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 345D L Excavator (Prefix JKN) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, bearings and other components into the travel motor housing and barrel. Measurements are taken throughout to ensure proper assembly. The travel motor is then installed on the excavator and filled with the correct oil type.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor. It details 27 steps for assembling the travel motor that include installing seals, springs, pistons, and other components in the proper order and orientation. Thirteen steps are listed for disassembling the final drive, which include removing the cover, gears, and planetary gear assembly. Personal injury warnings are provided and all components must be cleaned before assembly.
Caterpillar Cat 336E L Excavator (Prefix BZY) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor of a 336E L excavator. The disassembly procedure involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstalling parts. Special care must be taken when handling springs or parts under spring force to avoid injury.
Caterpillar Cat 330F and 330F L Excavator (Prefix LCG) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. It describes 37 steps to disassemble the final drive by removing gears, shafts, housings, seals and other components. It then describes 34 steps to reassemble the final drive, including pressing in new bearings, installing seals, adjusting bearing preload with shims, and applying threadlocker to bolts. Precise tools and lifting devices are required due to the heavy weights of up to 550 kg involved.
Caterpillar Cat 336E L Excavator (Prefix DPX) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor on a 336E L excavator. The disassembly process involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on lubricating parts and ensuring proper alignment of components.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fskekkdmdmdm3e
1) The document provides step-by-step instructions for disassembling the travel motor of a 336D2L excavator.
2) It describes removing over 30 components of the travel motor including the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates and more.
3) Detailed illustrations are provided to accompany each step showing how to remove each component using the recommended tools.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It describes 13 steps to remove the component, which include disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. 11 steps are listed to install the component, in reverse order, including attaching lifting devices, positioning the assembly, and reinstalling hoses and covers. Tools and torque specifications are provided.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLC) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for removing and installing a crankshaft wear sleeve and crankshaft gear on a 325C excavator. It describes using various tools to distort and remove the existing wear sleeve and instructions for installing a new sleeve using a multi-piece installer tool. It also outlines steps for removing the crankshaft gear using a bearing puller and installing the gear by heating it and pressing it onto the crankshaft. The document provides maintenance technicians with detailed parts and tool information as well as safety notices for completing these tasks.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for assembling and installing a travel motor. It outlines 34 steps for assembling components like pistons, seals, plates, and bearings. It also describes using tools to measure clearances and distances during assembly. Finally, it details installing the assembled travel motor using lifting devices and bolts, and connecting hydraulic hose assemblies.
More Related Content
Similar to Caterpillar Cat 323D LN and 323D S Excavator (Prefix DKW) Service Repair Manual Instant Download.pdf
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment to remove the flywheel housing and check the oil seal.
2) Cleaning the mating surfaces and installing a new gasket before reinstalling the housing.
3) Securing the housing with bolts and installing a new oil seal and crankshaft sleeve.
Caterpillar Cat 312B L EXCAVATOR (Prefix 2NS) Service Repair Manual (2NS00001...fusjekkdmdmd2w
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment to remove the flywheel housing and check the oil seal for wear.
2) Cleaning the mating surfaces and installing a new gasket before reinstalling the housing with bolts.
3) Installing a new oil seal and crankshaft wear sleeve with special tools during reinstallation.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing twelve bolts and the adapter to separate the housing from the flywheel.
2) Installing a new housing by positioning the adapter and securing it with twelve bolts.
3) Checking the flywheel runout after installation to ensure proper alignment.
Caterpillar Cat 312B L EXCAVATOR (Prefix 2NS) Service Repair Manual (2NS00001...f8usejkddmmd
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the adapter from the flywheel housing and remove the adapter.
2) Removing bolts to separate the inner ring from the flywheel and removing the inner ring.
3) Using lifting tools to remove the flywheel from the housing, which weighs 50kg.
4) Reversing the removal steps to install the flywheel housing, including securing the flywheel to the crankshaft with bolts and checking flywheel runout.
Caterpillar cat 312 b excavator (prefix 2ns) service repair manual (2ns00001 ...kmdddmm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Using lifting equipment to remove the flywheel housing and check the oil seal for wear.
2) Cleaning the mating surfaces and installing a new gasket before reinstalling the housing with bolts.
3) Installing a new oil seal and crankshaft wear sleeve with special tools during reinstallation.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing the flywheel, adapter, inner ring, and bolts securing the flywheel to the crankshaft.
2) Installing the flywheel using lifting tools, bolts, and checking runout with a gauge.
3) Removing the crankshaft rear seal and wear sleeve using drilling, hammer, and distorter tools.
4) Installing a new rear seal and wear sleeve using a installer, locator, bolts, washer and compound.
Similar to Caterpillar Cat 323D LN and 323D S Excavator (Prefix DKW) Service Repair Manual Instant Download.pdf (6)
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Removing bolts, seals and components to separate the swivel housing, rotor and cover.
2. Applying clean oil before reassembling components and installing seals, retainer and cover.
3. Draining swing motor oil before disconnecting hoses and removing bolts to detach the motor.
4. Dismantling the swing motor involves removing valves, seals, springs and using tools to separate individual parts like pistons, plates and barrels.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix YCF) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a piston pump. It outlines 30 steps for assembly, beginning with installing various bearings, seals, pistons, springs and other components in the proper order. Disassembly instructions describe 8 steps, including removing the head, port plate, bearings, pistons, pins and other parts. Safety warnings are provided to prevent injury from spring forces.
Caterpillar Cat 312D L Excavator (Prefix XGK) Service Repair Manual Instant D...fskekkdmdmdm3e
- The document provides instructions for removing and installing the idler gear of the front gear group on a C4.2 engine for Caterpillar built machines.
- To remove the idler gear, the front housing must first be removed. Then the idler gear bolt, thrust plate, and idler gear can be taken off the idler gear shaft. An idler shaft puller and driver group may be needed.
- To install the idler gear, first press in a new bushing if needed. Then install the idler shaft, idler gear, thrust plate, washer and idler gear bolt. Tighten the bolt to the specified torque.
Caterpillar Cat 336D L Excavator (Prefix J6D) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the final drive of a 336D L Mobile Hydraulic Power Unit. The 25 step disassembly process removes components like housing, gears, seals and bearings. The 22 step assembly process reverses this to rebuild the final drive, applying loctite and torquing bolts to specification. Tools required include link brackets, crossblocks, drivers and torque wrenches. Safety precautions are noted for releasing spring forces.
Caterpillar Cat 336F and 336F L Excavator (Prefix DSW) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling the travel motor on 336F and 336F L excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs and seals. Tools required include a transmission repair stand, lifting eye assembly, driver group and various bolts, pins and seals. Technicians are advised to mark components for reinstallation and take care when removing parts to avoid damage.
Caterpillar Cat 336D2 and 336D2 L Excavator (Prefix XBH) Service Repair Manua...fskekkdmdmdm3e
The document provides instructions for installing a swivel on an excavator. It describes using lifting devices and tools to position the swivel. O-rings and seals are installed on the swivel housing and rotor before assembling them together. Bolts are used to secure the parts and the swivel is tested for leaks by applying air pressure. Finally, hoses and fittings are reconnected to complete the installation.
Caterpillar Cat 345D L Excavator (Prefix JKN) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, bearings and other components into the travel motor housing and barrel. Measurements are taken throughout to ensure proper assembly. The travel motor is then installed on the excavator and filled with the correct oil type.
Caterpillar Cat 336E L Excavator (Prefix FJH) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling a travel motor. It details 27 steps for assembling the travel motor that include installing seals, springs, pistons, and other components in the proper order and orientation. Thirteen steps are listed for disassembling the final drive, which include removing the cover, gears, and planetary gear assembly. Personal injury warnings are provided and all components must be cleaned before assembly.
Caterpillar Cat 336E L Excavator (Prefix BZY) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor of a 336E L excavator. The disassembly procedure involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstalling parts. Special care must be taken when handling springs or parts under spring force to avoid injury.
Caterpillar Cat 330F and 330F L Excavator (Prefix LCG) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling a final drive on an excavator model 330F. It describes 37 steps to disassemble the final drive by removing gears, shafts, housings, seals and other components. It then describes 34 steps to reassemble the final drive, including pressing in new bearings, installing seals, adjusting bearing preload with shims, and applying threadlocker to bolts. Precise tools and lifting devices are required due to the heavy weights of up to 550 kg involved.
Caterpillar Cat 336E L Excavator (Prefix DPX) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor on a 336E L excavator. The disassembly process involves removing 27 individual parts from the travel motor in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on lubricating parts and ensuring proper alignment of components.
Caterpillar Cat 336D2 L Excavator (Prefix GJA) Service Repair Manual Instant ...fskekkdmdmdm3e
1) The document provides step-by-step instructions for disassembling the travel motor of a 336D2L excavator.
2) It describes removing over 30 components of the travel motor including the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates and more.
3) Detailed illustrations are provided to accompany each step showing how to remove each component using the recommended tools.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fskekkdmdmdm3e
The document provides instructions for removing and installing the final drive and travel motor on a 336D L excavator. It describes 13 steps to remove the component, which include disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. 11 steps are listed to install the component, in reverse order, including attaching lifting devices, positioning the assembly, and reinstalling hoses and covers. Tools and torque specifications are provided.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLD) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for disassembling and assembling the final drive of a 325C excavator. It lists required tools and gives step-by-step directions to remove and install components like gears, carriers, seals, and housings. Cleanliness is emphasized and O-rings, gaskets, and seals should always be replaced. The assembly procedure is the reverse of the disassembly with notes to apply lubricants and check parts for wear.
Caterpillar Cat 325C and 325C L Excavator (Prefix JLC) Service Repair Manual ...fskekkdmdmdm3e
The document provides instructions for removing and installing a crankshaft wear sleeve and crankshaft gear on a 325C excavator. It describes using various tools to distort and remove the existing wear sleeve and instructions for installing a new sleeve using a multi-piece installer tool. It also outlines steps for removing the crankshaft gear using a bearing puller and installing the gear by heating it and pressing it onto the crankshaft. The document provides maintenance technicians with detailed parts and tool information as well as safety notices for completing these tasks.
Caterpillar Cat 345D L Excavator (Prefix MLK) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for assembling and installing a travel motor. It outlines 34 steps for assembling components like pistons, seals, plates, and bearings. It also describes using tools to measure clearances and distances during assembly. Finally, it details installing the assembled travel motor using lifting devices and bolts, and connecting hydraulic hose assemblies.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual Instant D...fskekkdmdmdm3e
This document provides instructions for removing and installing the rear gear group and rear crankshaft seal of a C13 engine. The removal procedure involves 11 steps including removing bolts, gears, seals, and bearings. The installation procedure involves 12 steps including cleaning parts, installing bearings, seals, gears, and bolts while ensuring proper dimensions and torque specifications are followed. Tools required include drivers, link brackets, guide studs, and installation tools.
This document provides instructions for removing and installing a camshaft on a Caterpillar 3306B engine. It describes:
1) Marking the gears to ensure proper timing during removal and installation.
2) Removing the camshaft bolts and carefully removing the camshaft.
3) Cleaning and lubricating the camshaft lobes and bearings before installation.
4) Aligning the timing marks and installing the camshaft bolts to complete the process.
The document provides instructions for removing and installing various components of a Caterpillar 621E wheel scraper, including:
1) Removing and installing the push-pull plate that connects the push-pull spring to the support assembly.
2) Disassembling and assembling the push-pull spring itself by removing discs and plates.
3) A detailed process for removing and installing the ejector cylinder, which requires the use of lifting tools and wood blocks due to the cylinder's weight.
4) Brief instructions for removing and adjusting the position of the lower front and guide rollers on the ejector assembly.
This document provides assembly instructions for a final drive on an excavator. It involves assembling and installing several components in the following order: installing bearings and determining shim thickness; installing seals; installing dowel pins; installing the housing on the motor housing; installing coupling gear, bolts, and ring gear; assembling carrier assemblies; installing gears, shafts, and retaining rings; installing the cover and testing for leaks. The process requires precision measurements and uses several specialized tools to properly assemble the final drive.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567208
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B Forcing screws M16 X 2 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00605492
1. Remove twelve bolts (1) and washers from the adapter (2) .
2. Remove the adapter (2) from the flywheel housing.
Illustration 2 g00605497
3. Remove four socket head bolts (3) from the inner ring (4) .
4. Remove the inner ring (4) from the flywheel.
2/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00605501
5. Remove six bolts (5) that secure flywheel (6) to the crankshaft. Check all bolts for stripped
threads. Replace the bolts, if necessary.
Illustration 4 g00605504
6. Install Tool (A), a strap, and a suitable lifting device onto the flywheel (6).
7. Use Tool (B) in order to remove the flywheel and ring gear out of the housing. The weight
of the flywheel is 50 kg (110 lb).
8. Perform the following procedure in order to remove the flywheel ring gear.
Illustration 5 g00613038
a. Place the flywheel and ring gear assembly on a suitable support.
Note: Check the flywheel ring gear for the following conditions:cracks, damaged
dowel holes, worn ring gear and damaged ring gear.
Note: Identify the orientation of the old ring gear on the flywheel for proper
positioning, when the new ring gear is installed.
3/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Always wear protective gloves when handling parts that have been
heated.
b. Heat ring gear (7) uniformly.
c. Remove the ring gear (7) by tapping the ring gear all the way around the flywheel
(6) .
d. Reposition the flywheel in order to remove the ring gear.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 1 22:56:07 UTC+0800 2020
4/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01567260
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Heat the ring gear to 150 °C (302 °F) in an oven.
1/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. b. Press the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g00605504
2. Install Tool (A), a strap, and a suitable lifting device onto flywheel (6) .
3. Install flywheel (6). The weight of the flywheel is 50 kg (110 lb).
Illustration 2 g00605501
4. Install six bolts (5) in order to secure flywheel (6) onto the crankshaft. Tighten the bolts to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tool (A) from the flywheel.
2/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 3 g00605497
6. Place the inner ring (4) in position on the flywheel.
7. Install four socket head bolts (3) in order to secure the inner ring (4) to the flywheel.
Illustration 4 g00605492
8. Place the adapter (2) in position on the flywheel housing.
9. Install twelve bolts and washers (1) in order to secure the adapter (2) on the flywheel
housing.
10. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 1 22:57:06 UTC+0800 2020
3/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 1 22:59:05 UTC+0800 2020
3/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i05421135
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the electric starting motor.
B. Remove the flywheel and ring gear.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g00605593
1. Install Tooling (A) , a strap, and a suitable lifting device onto flywheel housing (2) .
2. Remove bolts (1) and the washers that secure flywheel housing (2) to the cylinder block.
Note: Identify the four shorter bolts for later installation into the flywheel housing.
3. Remove flywheel housing (2) . The weight of the flywheel is approximately.29 kg (65 lb).
4. Check oil seal (3) for serviceability. If necessary, replace the oil seal and crankshaft wear
sleeve.
Illustration 2 g00605601
5. Use Tooling (B) in order to remove the oil seal (3) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
2/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. B 9U-6170 Installer Gp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00605593
1. Clean old gasket material (4) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
2. Place flywheel housing (2) in position on the cylinder block.
3. Install the washers and bolts (1) in order to secure flywheel housing (2) to the cylinder
block.
4. Use Tooling (B) in order to install the oil seal (3) , and the crankshaft wear sleeve (not
shown).
End By:
a. Install the flywheel.
b. Install the electric starting motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 1 23:00:04 UTC+0800 2020
3/3
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01578488
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket (1)
1
( 1 )
Tool (B) is a 46 mm socket.
Start By:
A. Remove the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g00604778
1. Use Tool (B) to remove nut (1) and washer (2) from the threaded end of the crankshaft.
Illustration 2 g00604784
2. Use Tool (A) to remove crankshaft pulley (3) from the engine.
2/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 3 g00604792
3. If it is necessary to remove the wear sleeve (4) from the crankshaft pulley (3), use a hammer
and a chisel. Hold the chisel at right angles to the surface of the wear sleeve. Tap the wear
sleeve in three places. You can remove the wear sleeve once the tension is released.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 4 g00604778
3/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 1. Put crankshaft pulley (3) in position on the engine.
2. Install washer (2) and nut (1). Use Tool (B) to tighten nut (1) to a torque of 490 ± 10 N·m
(361 ± 7 lb ft).
End By: Install the V-belts. Refer to Disassembly and Assembly, "V-Belts - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 1 23:01:03 UTC+0800 2020
4/4
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01131366
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
A. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft front seal (1) .
2. Use Tool (A) and remove crankshaft front seal (1). Remove the seal evenly by alternating
the position of Tool (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 1 23:02:02 UTC+0800 2020
2/2
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i02080454
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 1 g00612743
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Install new crankshaft front seal (1) in the front housing with Tool (A) .
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By: Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Oct 1 23:03:02 UTC+0800 2020
2/2
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D S EXCAVATOR DKW
Configuration: 323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615339
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Note: Before removal, ensure that the marks on the timing gears are in alignment. Align the
fuel injection drive gear with the "33" mark with the "3" mark on the idler gear. Make an
alignment of the "2" mark on the camshaft gear with the "22" mark on the idler gear. Align
the "1" mark on the crankshaft gear with the "11" mark on the idler gear. The No. 1 cylinder
is at the top center position when these marks are in alignment.
Illustration 1 g00611568
1. Remove idler gear bolt (1) and the washer from the idler gear shaft .
2. Remove thrust plate (2) from the idler gear shaft.
2/5
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 2 g00611569
3. Remove idler gear (3) from the idler gear shaft.
Illustration 3 g00611570
4. If necessary, use Tool (B) to remove bushing (4) (not shown) from idler gear (3) .
Illustration 4 g00611572
3/5
323D LN & 323D S Excavators DKW00001-UP (MACHINE) POWERED BY 3066 ...
2020/10/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...