This document provides instructions for disassembling and assembling the travel motor of a 323D and 323D L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, brake piston, barrel assembly, and shaft assembly. It then describes 11 steps to assemble the travel motor by installing components like the lip seal, shaft assembly, cam plate, and barrel assembly. The goal is to thoroughly clean components prior to assembly and ensure all parts are reinstalled in their original locations and orientations.
Caterpillar cat 323 d excavator (prefix sdc) service repair manual (sdc00001 ...soeldksejdksem
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly instructions, listing 27 steps to remove components such as the head, brake piston, barrel assembly, and shaft assembly. It then provides assembly instructions in 26 steps, placing components back into the travel motor in reverse order, and noting to clean parts and apply lubricants. Precise positioning and alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar cat 323 d l excavator (prefix sdc) service repair manual (sdc0000...fjskksmem
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly instructions, listing 27 steps to remove components such as the head, check valves, fittings, seals, brake piston, plates, and shaft. It then provides assembly instructions in 25 steps, listing the components to be installed in reverse order, and noting to clean parts and apply oil or seals at various steps. Precise positioning and alignment of parts is emphasized to ensure proper reassembly.
Caterpillar cat 323 d2 l excavator (prefix tdt) service repair manual (tdt000...fjkskekxsdcmdmme
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly section lists 24 steps to reinstall these components in reverse order, noting specific installation procedures and component orientations. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...f7fujksekmdm8u
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, which include removing the head, brake piston, barrel assembly, and other components. It then lists 13 steps for assembly, which involve installing seals, the shaft assembly, cam plate, springs and other parts back into the travel motor body. Safety precautions are noted, such as containing fluids and applying sealant to surfaces.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...f8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes precautions to ensure correct installation of components like the cam plate, piston shoe assemblies, and brake piston. Special tools may be required and clean hydraulic oil should be applied to sealing surfaces during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...ufjksemd8ujd
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly section lists 24 steps to reinstall these components in the reverse order, noting proper orientation and cleaning of parts. Precautions are provided to avoid damaging components and ensure correct assembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...jdkskmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes precautions to ensure correct installation of components like the cam plate, piston shoe assemblies, and brake piston. Special tools may be required and clean hydraulic oil should be applied to sealing surfaces during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...prmy389342
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during reassembly.
Caterpillar cat 323 d excavator (prefix sdc) service repair manual (sdc00001 ...soeldksejdksem
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly instructions, listing 27 steps to remove components such as the head, brake piston, barrel assembly, and shaft assembly. It then provides assembly instructions in 26 steps, placing components back into the travel motor in reverse order, and noting to clean parts and apply lubricants. Precise positioning and alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar cat 323 d l excavator (prefix sdc) service repair manual (sdc0000...fjskksmem
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly instructions, listing 27 steps to remove components such as the head, check valves, fittings, seals, brake piston, plates, and shaft. It then provides assembly instructions in 25 steps, listing the components to be installed in reverse order, and noting to clean parts and apply oil or seals at various steps. Precise positioning and alignment of parts is emphasized to ensure proper reassembly.
Caterpillar cat 323 d2 l excavator (prefix tdt) service repair manual (tdt000...fjkskekxsdcmdmme
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly section lists 24 steps to reinstall these components in reverse order, noting specific installation procedures and component orientations. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...f7fujksekmdm8u
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, which include removing the head, brake piston, barrel assembly, and other components. It then lists 13 steps for assembly, which involve installing seals, the shaft assembly, cam plate, springs and other parts back into the travel motor body. Safety precautions are noted, such as containing fluids and applying sealant to surfaces.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...f8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes precautions to ensure correct installation of components like the cam plate, piston shoe assemblies, and brake piston. Special tools may be required and clean hydraulic oil should be applied to sealing surfaces during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...ufjksemd8ujd
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly section lists 24 steps to reinstall these components in the reverse order, noting proper orientation and cleaning of parts. Precautions are provided to avoid damaging components and ensure correct assembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...jdkskmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes precautions to ensure correct installation of components like the cam plate, piston shoe assemblies, and brake piston. Special tools may be required and clean hydraulic oil should be applied to sealing surfaces during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...prmy389342
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...8ufjsekddm8u
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, which include removing the head, brake piston, barrel assembly, and other components. It then lists 13 steps for assembly, which involve installing seals, the shaft assembly, cam plate, springs and other parts back into the travel motor body. Safety precautions are noted, such as containing fluids and applying pipe sealant to seal surfaces.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual Instant ...zan2736ban
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, brake piston, barrel assembly, shoe retainer, and shaft assembly. It then lists 13 steps for assembling the travel motor, including installing seals, keys, cam plate and other components in the reverse order of disassembly. Safety precautions are provided to contain fluids and properly handle components.
Caterpillar cat 323 d2 l excavator (prefix tdt) service repair manual (tdt000...idkdkddmd
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, which include removing the head, brake piston, barrel assembly, and other components. It then lists 13 steps for assembly, which involve installing seals, the shaft assembly, cam plate, springs and other parts back into the travel motor body. Safety precautions are noted, such as containing fluids and applying sealant to surfaces.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual Instant ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during assembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...km7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual Instant ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during reassembly.
Caterpillar cat 323 d2 l excavator (prefix ycr) service repair manual (ycr000...fjkskekxsdcmdmme
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, check valves, fittings, piston guide, brake piston, barrel assembly and more. The assembly section lists 24 steps to reinstall these components in reverse order, noting proper orientation and cleaning of parts. Precautions are provided to avoid damage and ensure correct installation of components like the cam plate and piston shoe assemblies.
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...ufjksemd8ujd
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, barrel assembly, and piston assemblies. Detailed illustrations are provided to identify the specific components and guide the disassembly process.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires draining fluids, removing mounting bolts and seals, and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and sockets, which may require removing a wear sleeve.
- Removing the crankshaft front seal using a slide hammer puller after drilling holes in the seal.
- Installing a new crankshaft front seal using a installer tool and applying oil to the seal and crankshaft pulley.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding containing fluids, releasing pressures, and being struck by parts under spring force.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the motor head, brake piston, barrel assembly, springs and seals. The assembly process is outlined in 13 steps and provides details on cleaning, lubricating and installing components in the reverse order of disassembly. Special notes are provided regarding alignment marks, spring pressure hazards and orientation of parts.
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...ufjksemd8ujd
This document provides instructions for disassembling various components of an excavator final drive and travel motor system. It outlines 16 steps to disassemble the final drive which include draining fluids, removing fittings and valves, and using tools to pull bearings. It also details 14 steps to disassemble the travel motor which involve removing seals, pistons, plates and springs. Safety notices are included throughout to warn of potential injuries from parts or released pressures.
Caterpillar Cat 312D2 L Excavator (Prefix KLE) Service Repair Manual (KLE0000...ufjksemd8ujd
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and noting part orientations for reassembly. Safety notices warn of risks such as fluid pressure, heavy component weights, and released spring forces.
This document provides instructions for removing and installing the front gear group on Caterpillar C4.4 engines. The removal procedure involves locking the crankshaft, camshaft, and fuel injection pump in position using timing pins. Components like the idler gears, camshaft gear, and housing bearing are then removed. Installation follows the reverse order, with lubrication of gears and checking of timing, backlash, and end play measurements upon completion. Tools and torque specifications are provided.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...ufjksemd8ujd
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to clearly show how to disassemble the various systems.
Caterpillar Cat 312D2 L Excavator (Prefix WHJ) Service Repair Manual (WHJ0000...ufjksemd8ujd
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening bolts to specification.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing a crankshaft rear seal housing assembly using alignment tools and tightening setscrews in a specific order.
- Removing and installing a crankshaft wear sleeve using pullers and installation sleeves to reclaim worn seal surfaces.
Caterpillar Cat 312D2 L Excavator (Prefix MGJ) Service Repair Manual (MGJ0000...ufjksemd8ujd
The document provides instructions for installing a flywheel and crankshaft rear seal on a 3054C engine. It includes:
1) Heating the ring gear to install it on the flywheel, then installing the flywheel using guide bolts and tightening bolts to the specified torque.
2) Removing the crankshaft rear seal housing assembly by removing setscrews, as the seal is non-serviceable and the housing must be replaced.
3) Installing the new crankshaft rear seal housing assembly by positioning it over the crankshaft, aligning it, and tightening setscrews to the specified torque using an alignment tool.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...ufjksemd8ujd
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists the required tools and outlines 16 steps to disassemble parts like the traction control valve, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluids.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...ufjksemd8ujd
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, torquing bolts in a specific sequence, and refilling fluids before installing removed components.
More Related Content
Similar to Caterpillar Cat 323D Excavator (Prefix SDC) Service Repair Manual (SDC00001 and up).pdf
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...8ufjsekddm8u
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, which include removing the head, brake piston, barrel assembly, and other components. It then lists 13 steps for assembly, which involve installing seals, the shaft assembly, cam plate, springs and other parts back into the travel motor body. Safety precautions are noted, such as containing fluids and applying pipe sealant to seal surfaces.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual Instant ...zan2736ban
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, brake piston, barrel assembly, shoe retainer, and shaft assembly. It then lists 13 steps for assembling the travel motor, including installing seals, keys, cam plate and other components in the reverse order of disassembly. Safety precautions are provided to contain fluids and properly handle components.
Caterpillar cat 323 d2 l excavator (prefix tdt) service repair manual (tdt000...idkdkddmd
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, which include removing the head, brake piston, barrel assembly, and other components. It then lists 13 steps for assembly, which involve installing seals, the shaft assembly, cam plate, springs and other parts back into the travel motor body. Safety precautions are noted, such as containing fluids and applying sealant to surfaces.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual Instant ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during assembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...km7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual Instant ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during reassembly.
Caterpillar cat 323 d2 l excavator (prefix ycr) service repair manual (ycr000...fjkskekxsdcmdmme
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, check valves, fittings, piston guide, brake piston, barrel assembly and more. The assembly section lists 24 steps to reinstall these components in reverse order, noting proper orientation and cleaning of parts. Precautions are provided to avoid damage and ensure correct installation of components like the cam plate and piston shoe assemblies.
Similar to Caterpillar Cat 323D Excavator (Prefix SDC) Service Repair Manual (SDC00001 and up).pdf (8)
Caterpillar Cat 313F L Excavator (Prefix NLG) Service Repair Manual (NLG00001...ufjksemd8ujd
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides instructions for disassembling the final drive, travel motor, and various other components of a 313D2 excavator. It lists the required tools and safety precautions and then outlines 16 steps to disassemble parts like the final drive, traction control valve, counterbalance valve, travel motor, barrel assembly, and piston assemblies. Detailed illustrations are provided to identify the specific components and guide the disassembly process.
The document provides instructions for removing and installing various engine components on a Caterpillar C4.2 engine, including:
- Removing and installing the flywheel housing, which requires draining fluids, removing mounting bolts and seals, and installing a new gasket.
- Removing and installing the crankshaft pulley using pullers and sockets, which may require removing a wear sleeve.
- Removing the crankshaft front seal using a slide hammer puller after drilling holes in the seal.
- Installing a new crankshaft front seal using a installer tool and applying oil to the seal and crankshaft pulley.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 313D2 excavator. It lists the required tools and parts and outlines 16 steps to disassemble the final drive, 13 steps to disassemble the travel motor, and 15 steps to disassemble the counterbalance valve. Safety notices are included regarding containing fluids, releasing pressures, and being struck by parts under spring force.
This document provides instructions for removing the front housing on a C4.4 engine. It involves:
1. Removing various other components first like the fan, crankshaft pulley, oil pan, accessory drive, water pump and timing gears.
2. Disconnecting a harness assembly and removing bolts that secure a bypass tube to the front housing.
3. Removing bolts of various lengths that secure the front housing, and then removing the front housing from the engine.
This document provides instructions for disassembling and assembling the travel motor of a 313D2 excavator. The disassembly process involves 27 steps to remove components like the motor head, brake piston, barrel assembly, springs and seals. The assembly process is outlined in 13 steps and provides details on cleaning, lubricating and installing components in the reverse order of disassembly. Special notes are provided regarding alignment marks, spring pressure hazards and orientation of parts.
Caterpillar Cat 312D2 L Excavator (Prefix MPP) Service Repair Manual (MPP0000...ufjksemd8ujd
This document provides instructions for disassembling various components of an excavator final drive and travel motor system. It outlines 16 steps to disassemble the final drive which include draining fluids, removing fittings and valves, and using tools to pull bearings. It also details 14 steps to disassemble the travel motor which involve removing seals, pistons, plates and springs. Safety notices are included throughout to warn of potential injuries from parts or released pressures.
Caterpillar Cat 312D2 L Excavator (Prefix KLE) Service Repair Manual (KLE0000...ufjksemd8ujd
This document provides instructions for disassembling components of an excavator including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists required tools and outlines multi-step procedures involving removing fittings, draining fluids, loosening bolts, using pullers to remove bearings and seals, and noting part orientations for reassembly. Safety notices warn of risks such as fluid pressure, heavy component weights, and released spring forces.
This document provides instructions for removing and installing the front gear group on Caterpillar C4.4 engines. The removal procedure involves locking the crankshaft, camshaft, and fuel injection pump in position using timing pins. Components like the idler gears, camshaft gear, and housing bearing are then removed. Installation follows the reverse order, with lubrication of gears and checking of timing, backlash, and end play measurements upon completion. Tools and torque specifications are provided.
Caterpillar Cat 312D2 L Excavator (Prefix GWN) Service Repair Manual (GWN0000...ufjksemd8ujd
This document provides instructions for disassembling the final drive, travel motor, and other components of an excavator model 312D2. It lists the required tools and gives step-by-step procedures to remove parts like sprockets, valves, gears, plates, and seals. Safety warnings are provided to release pressures and springs carefully due to risk of injury from propelled parts. Detailed illustrations accompany each step to clearly show how to disassemble the various systems.
Caterpillar Cat 312D2 L Excavator (Prefix WHJ) Service Repair Manual (WHJ0000...ufjksemd8ujd
The document provides instructions for installing and removing various engine components on a Caterpillar 3054C engine, including:
- Installing the flywheel, which involves heating the ring gear, positioning the flywheel with guide bolts, and tightening bolts to specification.
- Removing the crankshaft rear seal housing assembly, which is non-serviceable and must be replaced as a unit.
- Installing a crankshaft rear seal housing assembly using alignment tools and tightening setscrews in a specific order.
- Removing and installing a crankshaft wear sleeve using pullers and installation sleeves to reclaim worn seal surfaces.
Caterpillar Cat 312D2 L Excavator (Prefix MGJ) Service Repair Manual (MGJ0000...ufjksemd8ujd
The document provides instructions for installing a flywheel and crankshaft rear seal on a 3054C engine. It includes:
1) Heating the ring gear to install it on the flywheel, then installing the flywheel using guide bolts and tightening bolts to the specified torque.
2) Removing the crankshaft rear seal housing assembly by removing setscrews, as the seal is non-serviceable and the housing must be replaced.
3) Installing the new crankshaft rear seal housing assembly by positioning it over the crankshaft, aligning it, and tightening setscrews to the specified torque using an alignment tool.
Caterpillar Cat 312D2 L Excavator (Prefix FAB) Service Repair Manual (FAB0000...ufjksemd8ujd
This document provides instructions for disassembling various components of an excavator, including the final drive, travel motor, counterbalance valve, and barrel assembly. It lists the required tools and outlines 16 steps to disassemble parts like the traction control valve, piston assemblies, springs, and seals. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluids.
Caterpillar Cat 312D2 L Excavator (Prefix EAB) Service Repair Manual (EAB0000...ufjksemd8ujd
1. The document provides instructions for removing and installing the cylinder head and lifter group on a Caterpillar 3054C engine.
2. Key steps include draining fluids, removing components like the exhaust manifold and fuel injectors, then gradually loosening and removing cylinder head bolts.
3. Reinstallation requires cleaning surfaces, torquing bolts in a specific sequence, and refilling fluids before installing removed components.
Caterpillar Cat 312D2 L Excavator (Prefix DGF) Service Repair Manual (DGF0000...ufjksemd8ujd
This document provides instructions for removing and installing a camshaft on a Caterpillar 3054C engine. The key steps are:
1. Remove the rocker shaft assembly, pushrods, and front housing.
2. Turn the engine upside down so the valve lifters are away from the camshaft.
3. Carefully remove the camshaft from the cylinder block.
4. Ensure the camshaft is clean and lubricated with oil before installing it in the reverse order of removal. Special care must be taken not to damage the lobes or bearings.
The document provides instructions for removing and installing a cylinder head on a Caterpillar 3054C engine:
1) Drain coolant and oil, remove ancillary components, and loosen head bolts in a gradual, reverse order to prevent distortion.
2) Use lifting equipment to carefully remove the 57 kg cylinder head. Clean the head and block mating surfaces.
3) Install a new head gasket and guide bolts, then lower the head into place. Tighten bolts in stages to the specified torque values using a degree wheel.
4) Reinstall removed components, refill fluids, and complete installation by installing glow plugs and other components removed earlier.
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 312D2 GC excavator. It lists the required tools and outlines 16 steps for disassembling the components. Safety notices are included to warn of potential injuries from parts under spring pressure, hydraulic oil pressure, and hot oil. The components are to be marked for proper reassembly.
This document provides instructions for removing and installing a crankshaft rear seal on a 3054C engine. The removal procedure involves taking out setscrews and the housing assembly. For installation, the new seal assembly is pushed onto the crankshaft flange with a plastic sleeve for protection. Setscrews are then tightened to secure the housing assembly to the cylinder block. Proper cleaning, alignment with tools, and torque specifications are emphasized to complete the process.
This document provides instructions for removing and installing various components of a Caterpillar 312D excavator engine, including:
- Removing and installing the flywheel housing, which requires lifting devices and bolts.
- Removing and installing the crankshaft rear seal, using a slide hammer, distorter, and installer tool.
- Removing and installing the crankshaft pulley, using a combination puller and socket tools. Heating may be required to install wear sleeves.
- Guidelines are provided for cleaning parts and applying retaining compounds during installation. Torque specifications and required tools are listed for each procedure.
The document provides instructions for installing a flywheel on a 3054C engine. It includes the following steps:
1. Clean the flywheel housing and inspect the crankshaft rear seal for leaks.
2. Heat the ring gear to 250°C and quickly install it on the flywheel, ensuring correct orientation.
3. Install guide bolts and lifting brackets to position the flywheel, then install and tighten the bolts to the specified torque.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR SDC
Configuration: 323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
323D Excavator Machine Systems
Media Number -RENR7500-07 Publication Date -01/02/2012 Date Updated -14/02/2012
i01219550
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Start By:
a. Remove the travel motor.
Reference: Refer to Disassembly and Assembly, "Travel Motor - Remove" in this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the
travel motor is 60 kg (132 lb).
1/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. 3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00510326
Note: During the removal of head (2) from the body of the travel motor, be careful not to
scratch or damage the mating surfaces of the components.
4. Remove socket head bolts (1).
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00510341
2/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 3 g00510349
6. Turn over head (2).
7. Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head.
8. Remove the two check valve assemblies from the head.
Note: There is a retainer under spring (9). This retainer is a press fit in head (2). Do not
remove the retainer.
9. Insert a dowel rod with a small diameter into hole (X). Tap the dowel rod with a plastic
hammer in order to remove spring (9), poppet (8) and seat (7) from the head.
Illustration 4 g00510351
10. Remove three fittings (10) and plugs (11) from the head. Remove the O-ring seal from each
fitting.
Illustration 5 g00510352
11. Remove three O-ring seals (12) and washer set (13) from the body of the travel motor.
12. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply
approximately 525 kPa (75 psi) of shop air pressure to brake release port (Y). Make sure
that the shop air pressure is free of water. Brake piston (14) will move up the piston guide,
and out of the piston guide. Remove brake piston (14) from the body of the travel motor.
3/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 6 g00510353
13. Remove O-ring seal (15) from the brake piston. Remove backup ring (16) from the brake
piston.
14. Remove O-ring seal (17) from the brake piston. Remove backup ring (18) from the brake
piston.
Illustration 7 g00510356
15. Remove piston guide (19), five friction plates (20) and the four steel plates from the body of
the travel motor.
Illustration 8 g00510359
4/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. 16. Remove O-ring seal (21) from the piston guide. Remove backup ring (22) from the piston
guide.
Illustration 9 g00510365
Note: Do not allow the components of barrel assembly (23) to come apart during the
removal from the travel motor. All of the components in the barrel assembly must be
reinstalled in the component's original location.
17. Use two large screwdrivers, as shown. Slowly remove barrel assembly (23) from the body
of the travel motor. Do not allow the components to fall apart.
Illustration 10 g00510502
Note: Shoe retainer (24) and piston shoe assemblies (25) are not serviced separately. Prior
to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put
identification marks on piston shoe assemblies (25) for assembly purposes. Identification
marks are used to identify the piston shoe assembly's location in shoe retainer (24) and
barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's
original bores in the shoe retainer and the barrel.
18. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the
piston shoe assemblies from the shoe retainer.
5/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 11 g00510504
19. Remove guide (27), spacer (28) and springs (29) from the barrel.
Illustration 12 g00510547
20. Remove cam plate (30) from the body of the travel motor.
Illustration 13 g00510550
21. Remove two keys (31) and the two locating pins (not shown) from the body of the travel
motor.
6/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 14 g00510551
22. Remove O-ring seal (33) from the body of the travel motor.
23. Use a soft faced hammer to remove shaft assembly (34) from the body of the travel motor.
Remove the shaft assembly in the direction that is indicated by the arrow. Refer to
Illustration 14.
Illustration 15 g00510595
24. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing
(36) with a press.
Illustration 16 g00510598
7/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. 25. Remove inner race (37) from shaft (34).
Illustration 17 g00510599
26. Remove lip seal (38) from the body of the travel motor.
Illustration 18 g00510605
27. Remove two stoppers (39) and the two pistons from the body of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 5 00:52:58 UTC+0800 2020
8/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR SDC
Configuration: 323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
323D Excavator Machine Systems
Media Number -RENR7500-07 Publication Date -01/02/2012 Date Updated -14/02/2012
i01706705
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
1. Make sure that all of the components of the travel motor are thoroughly clean and free of
dirt and debris prior to assembly.
Illustration 1 g00510595
2. Install retaining ring (35) in the groove on shaft (34).
3. Install bearing (36) on shaft (34) with a press. Install the bearing until the bearing contacts
the retaining ring.
1/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. 4. Install the other retaining ring on the opposite side of bearing (36).
Illustration 2 g00510598
5. Install inner race (37) on the end of shaft (34) until the inner race is seated against the
shoulder on the shaft.
Illustration 3 g00651891
(a) Body
6. Apply a thin coat of 5P-3413 Pipe Sealant on Surfaces (Y) of the body of the travel motor.
7. Use Tooling (A) in order to install lip seal (38).
8. Install lip type seal (38) in the body of the travel motor. Install the lip seal so that the sealing
lip is facing in the direction that is shown. Make sure that the lip seal contacts the
counterbore in the body of the travel motor.
Note: Slowly rotate shaft assembly (34) during the installation in order to make sure that the
shaft assembly does not bind in the body of the travel motor.
9. Apply clean hydraulic oil on the lip of lip seal (38).
2/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. 10. Use a press to install shaft assembly (34) in the body of the travel motor. Slowly rotate the
shaft during the installation in order to make sure that the shaft does not bind. Make sure
that the bearing on the shaft contacts the counterbore in the body of the travel motor.
Illustration 4 g00651960
NOTICE
The locating pin on each key is not centered. In order to prevent
damage to the barrel assembly during assembly of the travel motor, the
keys must be installed as shown. Also, the keys must be installed in the
key's original location in the body of the travel motor.
11. Install the two locating pins and two keys (31) in the body of the travel motor, as shown.
Illustration 5 g00510547
3/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. 12. Install cam plate (30) in the body of the travel motor in the cam plate's original location.
Make sure that the two pistons and two keys (31) in the body of the travel motor engage
properly with the cam plate.
Illustration 6 g00510504
13. Install nine springs (29) in the barrel. Install spacer (28) and guide (27) on the barrel.
Illustration 7 g00878253
14. Install piston shoe assemblies (25) in the piston shoe assembly's original bores in shoe
retainer (24).
15. Apply clean hydraulic oil in the bores of the barrel and on piston shoe assemblies (25).
Install the piston shoe assemblies with the shoe retainer in the piston shoe assembly's
original bore in barrel (26).
NOTICE
Make sure that the cam plate is correctly engaged with the two pistons
in the body of the travel motor prior to installing the barrel assembly.
When the body of the travel motor is tilted to allow the installation of
the barrel assembly, the cam plate can slide off of the two pistons. The
remaining parts of the travel motor can be assembled with the cam
plate in the incorrect position.
4/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Extensive damage will result from the incorrect installation of the cam
plate. Follow the exact installation procedure to prevent damage.
16. Apply clean hydraulic oil on the sliding surfaces of the cam plate, on the piston shoe
assemblies and on the splined shaft of the travel motor.
Illustration 8 g00485953
17. Route a piece of strong string through an opening for the cam plate tension adjusters. Route
the string over the sliding surface of cam plate (30) and through the opposite opening for the
cam plate tension adjusters. Hold the string taut in order to keep cam plate (30) correctly
engaged with keys (31). Keep the string taut and position the body of the travel motor on the
body's side. Do not release the tension on the string at this time. Install barrel assembly (23)
as a unit on the shaft. Pull the string out of the body of the travel motor. It may be necessary
to pull the barrel assembly and the piston shoe assemblies away from the cam plate slightly
in order to release the string.
Illustration 9 g00651967
5/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. 18. Install O-ring seal (21) and backup ring (22) on piston guide (19), as shown.
Illustration 10 g00510356
19. Place the body of the travel motor in a vertical position.
20. Apply clean hydraulic oil on five friction plates (20) and the four steel plates. Install the
plates in alternating order in the body of the travel motor. Start with a friction plate and end
with a friction plate.
21. Install piston guide (19) in the body of the travel motor until the piston guide contacts the
counterbore in the body of the travel motor.
Illustration 11 g00878297
Note: Make sure that brake piston (14) is thoroughly clean and free of dirt and debris.
22. Install O-ring seal (16). Install backup ring (15).
23. Install O-ring seal (17). Install backup ring (18).
6/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. 24. Apply a thin coat of hydraulic oil on the surfaces of piston (14) which contact the body of
the travel motor. Install piston (14) in the body of the travel motor by hand. It may be
necessary to use a soft faced hammer to seat the piston correctly.
Illustration 12 g00878299
Illustration 13 g00878239
25. Install washer set (12) in piston (14), as shown.
26. Install O-ring seals (13) in the body of the travel motor, as shown.
7/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 14 g00510605
27. Install the two pistons and two stoppers (39) in the housing of the travel motor. Tighten the
stoppers to a torque of 140 ± 14 N·m (105 ± 10 lb ft).
Illustration 15 g00510351
28. Install the O-ring seals on fittings (10). Apply 5P-3413 Pipe Sealant on the threads of
fittings (10). Install the fittings in the head, as shown.
29. Install plugs (11) in the head. Tighten each plug to a torque of 15 ± 2 N·m (11 ± 1 lb ft).
Illustration 16 g00510349
8/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 17 g00510341
30. Apply a thin coat of 9S-3263 Thread Lock Compound on the threads of the two check
valves. Install the check valves in the head.
31. Install seat (7), poppet (8) and spring (9) in the head at Location (X).
32. Install O-ring seal (6) in the head, as shown.
33. Install bearing (3) in the head until the bearing contacts the counterbore in the cover.
34. Apply 1U-6396 O-Ring Assembly Compound on port plate (4). Install the port plate in the
port plate's original position on the motor cover.
35. Use a shim or shims (5) so that the following requirements are met.
Note: During the following checks, turn the travel motor output shaft in a clockwise
direction.
a. The travel motor output shaft does not rotate with an applied torque of 440 N·m
(325 lb ft) or more with the parking brake release port open.
b. The travel motor output shaft rotates with an applied torque of 29 N·m (21 lb ft) or
less when the parking brake release port is pressurized to 780 kPa (115 psi) with both
the inlet port and the outlet port open to the hydraulic oil tank.
Note: It may be necessary to remove head (2) several times in order to determine the correct
thickness of shim or shims (5) that are used to adjust the rolling torque of the travel motor
output shaft.
36. Apply a thin layer of 5P-0960 Molybdenum Grease on shim or shims (5). Install the shim or
shims on the head. The grease will hold the shim or shims in place during the installation of
the head. Install the head on the body of the travel motor.
9/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 18 g00510326
37. Place head (2) in the head's original position on the travel motor. Install socket head bolts
(1) that secure the head. Tighten the socket head bolts to a torque of 175 ± 18 N·m
(130 ± 13 lb ft).
NOTICE
To prevent possible damage to the travel motor, fill the unit with oil at
least to the fill port before operating the machine. Refer to the
Operation and Maintenance Manual for the correct oil specification.
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install" in this
manual.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 5 00:53:57 UTC+0800 2020
10/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engi...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR SDC
Configuration: 323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
323D Excavator Machine Systems
Media Number -RENR7500-07 Publication Date -01/02/2012 Date Updated -14/02/2012
i03524320
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded Rod M16 by 381mm 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/3
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 1 g00651795
2. Install a new O-ring seal (5) . Apply clean hydraulic oil on O-ring seal (5) .
Illustration 2 g00707267
3. Attach a suitable lifting device to travel motor (4) , as shown. The weight of travel motor (4)
is approximately 57 kg (125 lb).
Illustration 3 g00944825
2/3
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. 4. Carefully install travel motor (4) on Tooling (A) . Slide travel motor (4) into the final drive.
5. Install bolt (2A) that secures travel motor (4) to the final drive.
6. Remove Tooling (A) .
Illustration 4 g00707275
Typical example
7. Install bolts (2) .
8. Connect hose assemblies (3) and (1) .
9. Fill the final drive with oil. Refer to Operation and Maintenance Manual, "Lubricant
Viscosities" for the proper oil viscosity. Refer to Operation and Maintenance Manual, "Final
Drive Oil Level - Check" for the correct filling procedure.
10. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
11. Obtain a hydraulic oil sample from the main S·O·S port. Refer to Operation and
Maintenance Manual, "Sampling Interval and Location of Sampling Valve" for the correct
location.
12. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system. Refer to Contamination
Control Guideline, SEBF8447 for further information.
End By: Install the counterbalance valve. Refer to Disassembly and Assembly, "Counterbalance
Valve (Travel) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 5 00:54:57 UTC+0800 2020
3/3
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR SDC
Configuration: 323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
323D Excavator Machine Systems
Media Number -RENR7500-07 Publication Date -01/02/2012 Date Updated -14/02/2012
i05453056
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C
154-6184 Forcing Bolt (M 20) 2
154-6185(1)
Forcing Bolt (M 24) 2
(1)
For Use on 329 and 330 sales models
Start By:
a. Separate the track assembly.
b. Remove the travel motor.
1/3
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 1 g00489826
Typical Example
Note: Adjust the height of Tooling (A) so that there is sufficient clearance between the
sprocket and the track for the removal of the final drive.
1. Lift the side of the machine in order to install Tooling (A) under the frame, as shown.
Illustration 2 g00712767
2. Fasten Tooling (B) and a suitable lifting device to final drive (1), as shown. Put a slight
lifting tension on the final drive.
Illustration 3 g00712737
2/3
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Note: Mark the orientation of bolt holes (2) for the travel motor for installation purposes.
3. Remove bolts (3) and the washers from the final drive.
Illustration 4 g00712749
4. Use Tooling (C) in order to remove the final drive from the frame.
5. Carefully remove final drive (1). The weight of final drive (1) and the sprocket is
approximately 312 kg (688 lb).
6. Remove Tooling (C) from the frame.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 5 00:55:57 UTC+0800 2020
3/3
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR SDC
Configuration: 323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
323D Excavator Machine Systems
Media Number -RENR7500-07 Publication Date -01/02/2012 Date Updated -14/02/2012
i05453130
Final Drive - Disassemble
SMCS - 4050-015
S/N - BYM1-UP
S/N - CWG1-UP
S/N - CYD1-UP
S/N - DCJ1-UP
S/N - DKW1-UP
S/N - GTF1-UP
S/N - JLG1-UP
S/N - LFL1-UP
S/N - NDE1-UP
S/N - NES1-UP
S/N - PBE1-UP
S/N - PBM1-UP
S/N - RAC1-UP
S/N - SDC1-UP
S/N - SED1-UP
S/N - WGC1-UP
1/11
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. S/N - WNE1-UP
S/N - YSD1-UP
S/N - ZMF1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3938 Link Bracket 2
C 154-6181 Forcing Bolt 1
D 439-3940 Link Bracket 2
E
5F-7366 Forcing Bolt 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F - Loctite 5127 1
Start By:
a. Remove the final drive.
Note: Cleanliness is an important factor. Before the disassembly procedure, thoroughly
clean the exterior of the component. This action will prevent dirt from entering the internal
mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the original locations.
2/11
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from cover (2), and fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
Illustration 3 g00708091
3/11
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...