The document provides a 27 step procedure for disassembling a travel motor on a 323F and 323F LN excavator. It involves removing components like the head, fittings, seals, pistons, springs, and more. Detailed illustrations are provided to identify each part and show their location. Safety precautions are noted for releasing spring forces to avoid personal injury while following the recommended procedure and tools.
Caterpillar cat 314 e cr excavator (prefix ecn) service repair manual (ecn000...jfdskekdmme
The document provides instructions for removing and installing the front gear group on a Caterpillar C4.4 engine. Key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
2. Removing the idler gear and camshaft gear, taking note of alignment marks for reinstallation.
3. Cleaning and inspecting components, then reinstalling the gears in proper alignment, checking backlash and end play with gauges.
4. Locking components again and tightening fasteners to specification before removing locking pins and returning the valve mechanism to the safe position.
The document provides instructions for removing and installing the idler gear on a C4.4 engine. There are separate procedures for a standard idler gear and a heavy-duty idler gear. The removal procedure involves locking the camshaft and crankshaft, removing mounting bolts, and tilting the gear out of position. The installation procedure involves cleaning and inspecting parts, aligning timing marks, lubricating components, and checking specifications such as end play and backlash. Tools and torque specifications are provided.
Caterpillar cat 323 d sa excavator (prefix nes) service repair manual (nes000...jfdskekdmme
The document provides instructions for removing and installing the flywheel, flywheel housing, and crankshaft rear seal of a C6.4 engine. The flywheel is removed using lifting tools and bolts, while the flywheel housing requires removal of mounting bolts and contains a oil seal. Installation follows the reverse process, ensuring clean surfaces and applying retaining compound to mating parts. Special tools are specified for removing and installing the crankshaft rear seal and wear sleeve.
Caterpillar cat 314 f cr excavator (prefix raf) service repair manual (raf000...jfdskekdmme
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 314F excavator. It lists the required tools and outlines 23 steps to disassemble the components, including draining fluids, removing covers, plates, gears, seals, pistons, springs and other parts. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluids.
Caterpillar cat 314 e cr excavator (prefix ycw) service repair manual (ycw000...jfdskekdmme
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning parts and installing the oil cooler assembly with new gaskets and bolts. Tools, safety precautions, and maintenance tips are also provided.
Caterpillar cat 314 e cr excavator (prefix gmd) service repair manual (gmd000...jfdskekdmme
This document provides instructions for disassembling various components of a 314E CR excavator, including the final drive, travel motor, counterbalance valve, and travel motor. It lists the required tools and outlines a step-by-step process for safely removing each part, noting precautions for releasing pressures and contained fluids. Detailed illustrations accompany each step to ensure correct reassembly.
Caterpillar cat 323 f excavator (prefix kby) service repair manual (kby00001 ...jfdskekdmme
This document provides instructions for removing and installing the rear power take-off (RPTO) on a Caterpillar 323F excavator engine. The removal procedure involves removing 12 components including gears, adapters, and sleeve bearings. The installation procedure describes installing these components in reverse order and ensuring proper alignment and torque specifications are followed.
Caterpillar cat 314 c lcr excavator (prefix kja) service repair manual (kja00...jfdskekdmme
This document provides disassembly instructions for the final drive, travel motor, and other components of a 314C excavator. It lists required tools and outlines over 30 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and planetary gear assemblies. Safety notices are included throughout to warn of hazards like released spring forces and hot or pressurized fluids.
Caterpillar cat 314 e cr excavator (prefix ecn) service repair manual (ecn000...jfdskekdmme
The document provides instructions for removing and installing the front gear group on a Caterpillar C4.4 engine. Key steps include:
1. Locking the crankshaft, camshaft, and fuel injection pump in position using timing pins to maintain proper timing.
2. Removing the idler gear and camshaft gear, taking note of alignment marks for reinstallation.
3. Cleaning and inspecting components, then reinstalling the gears in proper alignment, checking backlash and end play with gauges.
4. Locking components again and tightening fasteners to specification before removing locking pins and returning the valve mechanism to the safe position.
The document provides instructions for removing and installing the idler gear on a C4.4 engine. There are separate procedures for a standard idler gear and a heavy-duty idler gear. The removal procedure involves locking the camshaft and crankshaft, removing mounting bolts, and tilting the gear out of position. The installation procedure involves cleaning and inspecting parts, aligning timing marks, lubricating components, and checking specifications such as end play and backlash. Tools and torque specifications are provided.
Caterpillar cat 323 d sa excavator (prefix nes) service repair manual (nes000...jfdskekdmme
The document provides instructions for removing and installing the flywheel, flywheel housing, and crankshaft rear seal of a C6.4 engine. The flywheel is removed using lifting tools and bolts, while the flywheel housing requires removal of mounting bolts and contains a oil seal. Installation follows the reverse process, ensuring clean surfaces and applying retaining compound to mating parts. Special tools are specified for removing and installing the crankshaft rear seal and wear sleeve.
Caterpillar cat 314 f cr excavator (prefix raf) service repair manual (raf000...jfdskekdmme
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 314F excavator. It lists the required tools and outlines 23 steps to disassemble the components, including draining fluids, removing covers, plates, gears, seals, pistons, springs and other parts. Safety notices are included to warn of potential injuries from parts propelled by springs or pressurized hydraulic fluids.
Caterpillar cat 314 e cr excavator (prefix ycw) service repair manual (ycw000...jfdskekdmme
This document provides instructions for removing and installing an engine oil cooler on a Caterpillar C4.4 engine. The removal procedure involves draining coolant, removing mounting bolts and spacers, and removing the oil cooler assembly. The installation procedure specifies cleaning parts and installing the oil cooler assembly with new gaskets and bolts. Tools, safety precautions, and maintenance tips are also provided.
Caterpillar cat 314 e cr excavator (prefix gmd) service repair manual (gmd000...jfdskekdmme
This document provides instructions for disassembling various components of a 314E CR excavator, including the final drive, travel motor, counterbalance valve, and travel motor. It lists the required tools and outlines a step-by-step process for safely removing each part, noting precautions for releasing pressures and contained fluids. Detailed illustrations accompany each step to ensure correct reassembly.
Caterpillar cat 323 f excavator (prefix kby) service repair manual (kby00001 ...jfdskekdmme
This document provides instructions for removing and installing the rear power take-off (RPTO) on a Caterpillar 323F excavator engine. The removal procedure involves removing 12 components including gears, adapters, and sleeve bearings. The installation procedure describes installing these components in reverse order and ensuring proper alignment and torque specifications are followed.
Caterpillar cat 314 c lcr excavator (prefix kja) service repair manual (kja00...jfdskekdmme
This document provides disassembly instructions for the final drive, travel motor, and other components of a 314C excavator. It lists required tools and outlines over 30 steps to disassemble parts like the final drive, travel motor, counterbalance valve, and planetary gear assemblies. Safety notices are included throughout to warn of hazards like released spring forces and hot or pressurized fluids.
Caterpillar cat 314 c excavator (prefix sny) service repair manual (sny00001 ...jfdskekdmme
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of 314C and 314C CR excavators. It outlines 16 steps to disassemble the final drive which include removing fittings, bolts, and valves. It then details 14 steps to disassemble the counterbalance valve which involve removing springs, seals, pistons, and spools. Finally, it lists 10 steps to disassemble the travel motor which include removing seals, pistons, plates and barrel assemblies. Safety notices are included throughout to warn of hazards such as released pressures and falling/lifting heavy components.
Claas targo c50 40 (type 506) telehandlers service repair manualfjskekdmjekm
This document provides maintenance and repair information for CLAAS Targo C Series tractors. It covers axles and steering, the engine, transmission, boom, chassis, and technical specifications. Safety warnings are provided, and sections describe how to remove, repair, and install various components like the front and rear axles, steering system, engine, transmission, boom, cab, and other parts. Removal and installation procedures are outlined in detail with pictures to guide the repair work.
John deere 48 inch commercial walk behind mower service repair manualjfdskekdmme
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair procedures, and operational testing and adjustments. Safety precautions are outlined, including proper handling of fluids, preventing battery explosions, emergency preparedness, and protective equipment requirements.
Caterpillar cat 314 d lcr excavator (prefix ssz) service repair manual (ssz00...fjskekdmjekm
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 314D LCR excavator. It lists required tools and outlines 16 steps for disassembling the components, including draining fluids, removing fittings and valves, using pullers to remove bearings, and noting part orientations for reassembly. Safety notices are included to warn of potential injuries from pressurized fluids, heavy parts, and released spring forces.
Clark esm 12 forklift service repair manualjfdskekdmme
This service manual provides maintenance and repair information for Clark industrial lift trucks. It consists of modules covering specific systems, with each page numbered by group, section and page number. The drive axle group describes the drive axle components and removal/installation procedures. Key steps include draining the transmission fluid, removing mounting bolts in a specific order, and using lift straps to safely remove the drive axle and motors. Special tools are required for some drive axle fasteners.
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...fjkskedmme
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
Clark ewp45 forklift service repair manualjfdskekdmme
The document provides instructions for performing planned maintenance on lift trucks. It discusses the purpose and terminology of periodic service and planned maintenance. Recommended maintenance tasks are grouped into visual inspections and operational tests. Visual inspections include checking for oil leaks, damage to components, and tire condition. Operational tests involve testing brakes, steering, controls and other functions. Technicians are instructed to note any issues found using a coding system on a check sheet. Safety precautions are also provided, such as disconnecting the battery before exposing internal components.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...fjkskedmme
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices warn of potential spring forces and ensure fluids are contained.
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using lifting tools to remove the final drives from the excavator.
2. Detailed steps are given for disassembling the final drives, including removing gears, carriers, seals, and other components. Alignment marks should be made for reassembly.
3. Reassembly involves cleaning parts, applying threadlock and lubricant, and torquing bolts to specification. Seals and bearings must be installed correctly to prevent damage.
Claas targo k60 telehandlers service repair manualfjskekdmjekm
This document provides instructions for removing and installing the front and rear axles on a CLAAS agricultural machine. Key steps include draining hydraulic pressure and disconnecting electrical components before removing axles. Special care must be taken when removing the heavy axles, using proper lifting equipment. Torque specifications and bleeding procedures are listed for reinstallation. Safety warnings are also provided regarding proper protective equipment and following maintenance procedures.
This document provides instructions for removing and installing a swing motor and swing drive on an M315 excavator. It describes releasing hydraulic pressure, draining oil, disconnecting hoses, and removing and installing various components like bolts, seals, and motors. Safety precautions are provided regarding containing fluids, releasing pressure, and preventing personal injury. Detailed step-by-step instructions are given for disassembly and reassembly.
Caterpillar cat 314 c lcr excavator (prefix pca) service repair manual (pca00...jfdskekdmme
This document provides disassembly instructions for excavator models 314C, 314C CR, and 314C LCR. It describes how to disassemble components of the final drive, travel motor, counterbalance valve, and other systems. The instructions are detailed, listing each part and step in the disassembly process. Required tools are provided at the beginning. Safety notices are included throughout to warn of hazards like stored energy in springs.
Caterpillar cat 312 c excavator (prefix fds) service repair manual (fds00001 ...fjsjjekdkme
This document provides disassembly instructions for the 312C and 312C L excavator final drive, travel motor, and travel counterbalance valve systems. It outlines 17 steps to disassemble the final drive which includes removing covers, plates, gears, and bearings. It also details 13 steps to disassemble the travel motor such as removing piston assemblies, seals, and barrel components. Finally, it lists 15 steps for disassembling the travel counterbalance valve including removing springs, spools, valves, and housings. Personal safety notices are included throughout regarding releasing pressures and contained parts.
Caterpillar cat 326 d2 l excavator (prefix hm4) service repair manual (hm4000...fjsjekkmdmme
The document provides instructions for disassembling a travel motor. It involves 28 steps including removing the head, port plate, springs, pistons, seals, and other components. Tools required include an adapter, nuts, washers, threaded rod, bolts, eyebolts, retaining ring pliers, a bearing puller group, and other specialized tools to remove components in a specific sequence while taking safety precautions for parts under spring pressure.
Caterpillar cat 314 d lcr excavator (prefix txn) service repair manual (txn00...fjskekdmjekm
The document provides instructions for removing and installing the inlet manifold and inlet and exhaust valves on a Caterpillar 314D LCR excavator. The procedures include using various tools to compress springs, remove bolts and clips, and correctly position gaskets and other components. Precautions are outlined to prevent damage and ensure parts are clean prior to installation. Diagrams illustrate the components and steps in the processes.
Caterpillar cat 323 f ln excavator (prefix mfy) service repair manual (mfy000...jfdskekdmme
The document provides disassembly instructions for a travel motor in 3 sentences:
It begins by instructing the removal of the travel motor and cleaning of its exterior. Detailed steps are then given to disassemble the various components of the travel motor by removing fasteners, seals, plates, springs, and other parts. Precautions are included to safely release stored spring energy during disassembly.
Caterpillar cat 323 f excavator (prefix mfy) service repair manual (mfy00001 ...jfdskekdmme
This document provides disassembly instructions for a 323F and 323F LN excavator travel motor in 27 steps. It details removing components such as the head assembly, housing assembly, brake piston, friction discs, and rotating group. Proper tooling is required and safety precautions should be followed when releasing spring forces or using pressurized air. The travel motor must be thoroughly cleaned and components reinstalled in their original positions and orientations.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...djdksmmdmd
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, ensuring proper alignment and lubrication of parts.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, applying specified lubricants and ensuring proper alignment of parts.
Caterpillar cat 325 f l excavator (prefix yca) service repair manual (yca0000...dikskedmdm
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...shun96145luo
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Caterpillar cat 314 c excavator (prefix sny) service repair manual (sny00001 ...jfdskekdmme
This document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of 314C and 314C CR excavators. It outlines 16 steps to disassemble the final drive which include removing fittings, bolts, and valves. It then details 14 steps to disassemble the counterbalance valve which involve removing springs, seals, pistons, and spools. Finally, it lists 10 steps to disassemble the travel motor which include removing seals, pistons, plates and barrel assemblies. Safety notices are included throughout to warn of hazards such as released pressures and falling/lifting heavy components.
Claas targo c50 40 (type 506) telehandlers service repair manualfjskekdmjekm
This document provides maintenance and repair information for CLAAS Targo C Series tractors. It covers axles and steering, the engine, transmission, boom, chassis, and technical specifications. Safety warnings are provided, and sections describe how to remove, repair, and install various components like the front and rear axles, steering system, engine, transmission, boom, cab, and other parts. Removal and installation procedures are outlined in detail with pictures to guide the repair work.
John deere 48 inch commercial walk behind mower service repair manualjfdskekdmme
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair procedures, and operational testing and adjustments. Safety precautions are outlined, including proper handling of fluids, preventing battery explosions, emergency preparedness, and protective equipment requirements.
Caterpillar cat 314 d lcr excavator (prefix ssz) service repair manual (ssz00...fjskekdmjekm
The document provides disassembly instructions for the final drive, travel motor, and counterbalance valve of a 314D LCR excavator. It lists required tools and outlines 16 steps for disassembling the components, including draining fluids, removing fittings and valves, using pullers to remove bearings, and noting part orientations for reassembly. Safety notices are included to warn of potential injuries from pressurized fluids, heavy parts, and released spring forces.
Clark esm 12 forklift service repair manualjfdskekdmme
This service manual provides maintenance and repair information for Clark industrial lift trucks. It consists of modules covering specific systems, with each page numbered by group, section and page number. The drive axle group describes the drive axle components and removal/installation procedures. Key steps include draining the transmission fluid, removing mounting bolts in a specific order, and using lift straps to safely remove the drive axle and motors. Special tools are required for some drive axle fasteners.
Caterpillar cat 325 c l excavator (prefix amh) service repair manual (amh0000...fjkskedmme
This document provides instructions for removing and installing various engine components on Caterpillar 325C and 325C L excavators, including:
- Removing and installing the camshaft, camshaft gear, and camshaft bearings. Proper timing of the camshaft is emphasized.
- Removing and installing the engine oil pan. Safety precautions for hot oil and proper fluid containment are outlined.
- The document contains detailed step-by-step instructions, illustrations, and notes on proper component orientation for each procedure. Required tools are listed.
Caterpillar cat 325 c l excavator (prefix jlc) service repair manual (jlc0000...fjkskedmme
The document provides instructions for checking and servicing components of a Caterpillar 3126B engine, including:
1. Removing and installing a crankshaft rear wear sleeve, which requires using specialty tools to distort and remove the old sleeve before pressing in a new one.
2. Installing the crankshaft, which involves cleaning surfaces, applying oil, and torquing bolts to specifications while checking end play.
3. Removing and installing the crankshaft gear, which requires heating the gear and using a puller and hydraulic press for removal and installation.
4. Checking bearing clearance using a dial indicator in accordance with specifications.
Clark ewp45 forklift service repair manualjfdskekdmme
The document provides instructions for performing planned maintenance on lift trucks. It discusses the purpose and terminology of periodic service and planned maintenance. Recommended maintenance tasks are grouped into visual inspections and operational tests. Visual inspections include checking for oil leaks, damage to components, and tire condition. Operational tests involve testing brakes, steering, controls and other functions. Technicians are instructed to note any issues found using a coding system on a check sheet. Safety precautions are also provided, such as disconnecting the battery before exposing internal components.
Caterpillar cat 336 f lxe excavator (prefix pfl) service repair manual (pfl00...fjkskedmme
This document provides instructions for disassembling the travel motor on 336F XE and 336F LXE excavator models. The 27-step procedure includes removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals and plates. Detailed illustrations accompany each step to show how to position tools and disassemble individual parts. Safety notices warn of potential spring forces and ensure fluids are contained.
1. The document provides instructions for removing and installing final drives on 320-series excavators. It describes disconnecting hydraulic lines, removing mounting bolts, and using lifting tools to remove the final drives from the excavator.
2. Detailed steps are given for disassembling the final drives, including removing gears, carriers, seals, and other components. Alignment marks should be made for reassembly.
3. Reassembly involves cleaning parts, applying threadlock and lubricant, and torquing bolts to specification. Seals and bearings must be installed correctly to prevent damage.
Claas targo k60 telehandlers service repair manualfjskekdmjekm
This document provides instructions for removing and installing the front and rear axles on a CLAAS agricultural machine. Key steps include draining hydraulic pressure and disconnecting electrical components before removing axles. Special care must be taken when removing the heavy axles, using proper lifting equipment. Torque specifications and bleeding procedures are listed for reinstallation. Safety warnings are also provided regarding proper protective equipment and following maintenance procedures.
This document provides instructions for removing and installing a swing motor and swing drive on an M315 excavator. It describes releasing hydraulic pressure, draining oil, disconnecting hoses, and removing and installing various components like bolts, seals, and motors. Safety precautions are provided regarding containing fluids, releasing pressure, and preventing personal injury. Detailed step-by-step instructions are given for disassembly and reassembly.
Caterpillar cat 314 c lcr excavator (prefix pca) service repair manual (pca00...jfdskekdmme
This document provides disassembly instructions for excavator models 314C, 314C CR, and 314C LCR. It describes how to disassemble components of the final drive, travel motor, counterbalance valve, and other systems. The instructions are detailed, listing each part and step in the disassembly process. Required tools are provided at the beginning. Safety notices are included throughout to warn of hazards like stored energy in springs.
Caterpillar cat 312 c excavator (prefix fds) service repair manual (fds00001 ...fjsjjekdkme
This document provides disassembly instructions for the 312C and 312C L excavator final drive, travel motor, and travel counterbalance valve systems. It outlines 17 steps to disassemble the final drive which includes removing covers, plates, gears, and bearings. It also details 13 steps to disassemble the travel motor such as removing piston assemblies, seals, and barrel components. Finally, it lists 15 steps for disassembling the travel counterbalance valve including removing springs, spools, valves, and housings. Personal safety notices are included throughout regarding releasing pressures and contained parts.
Caterpillar cat 326 d2 l excavator (prefix hm4) service repair manual (hm4000...fjsjekkmdmme
The document provides instructions for disassembling a travel motor. It involves 28 steps including removing the head, port plate, springs, pistons, seals, and other components. Tools required include an adapter, nuts, washers, threaded rod, bolts, eyebolts, retaining ring pliers, a bearing puller group, and other specialized tools to remove components in a specific sequence while taking safety precautions for parts under spring pressure.
Caterpillar cat 314 d lcr excavator (prefix txn) service repair manual (txn00...fjskekdmjekm
The document provides instructions for removing and installing the inlet manifold and inlet and exhaust valves on a Caterpillar 314D LCR excavator. The procedures include using various tools to compress springs, remove bolts and clips, and correctly position gaskets and other components. Precautions are outlined to prevent damage and ensure parts are clean prior to installation. Diagrams illustrate the components and steps in the processes.
Caterpillar cat 323 f ln excavator (prefix mfy) service repair manual (mfy000...jfdskekdmme
The document provides disassembly instructions for a travel motor in 3 sentences:
It begins by instructing the removal of the travel motor and cleaning of its exterior. Detailed steps are then given to disassemble the various components of the travel motor by removing fasteners, seals, plates, springs, and other parts. Precautions are included to safely release stored spring energy during disassembly.
Caterpillar cat 323 f excavator (prefix mfy) service repair manual (mfy00001 ...jfdskekdmme
This document provides disassembly instructions for a 323F and 323F LN excavator travel motor in 27 steps. It details removing components such as the head assembly, housing assembly, brake piston, friction discs, and rotating group. Proper tooling is required and safety precautions should be followed when releasing spring forces or using pressurized air. The travel motor must be thoroughly cleaned and components reinstalled in their original positions and orientations.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...djdksmmdmd
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, ensuring proper alignment and lubrication of parts.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, applying specified lubricants and ensuring proper alignment of parts.
Caterpillar cat 325 f l excavator (prefix yca) service repair manual (yca0000...dikskedmdm
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...shun96145luo
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, ensuring proper alignment and lubrication of parts. Special tools and procedures are required for some steps.
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and keys in their proper positions and applying sealant and grease as needed. The goal is to take the travel motor fully apart and then rebuild it correctly with all components returned to their original locations.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...f7useijdkdmd1
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and ensuring keys and pins are in their proper positions. The goal is to take the travel motor apart piece by piece and then rebuild it correctly during assembly.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...fjdkksmemd
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...f7siejdkdmd
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and ensuring keys and pins are in their proper positions. The goal is to take the travel motor apart piece by piece and then rebuild it correctly during assembly.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 325F LCR. It describes 25 steps to disassemble the various components of the travel motor by removing seals, plates, pistons, springs and other parts. It then describes 11 steps for reassembling the components, including installing seals, bearings, pins and keys in the proper positions and applying grease or sealant as needed. Precise positioning of parts is emphasized for correct reassembly.
Caterpillar cat 325 f lcr excavator (prefix yca) service repair manual (yca00...dikskedmdm
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and ensuring keys and pins are in their proper positions. The goal is to take the travel motor apart piece by piece and then rebuild it correctly during assembly.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence, taking care to mark parts for proper reinstallation.
3. The assembly procedure instructs assembling the travel motor components in the reverse order, applying specified lubricants and fasteners, and using tools as needed.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, ensuring proper alignment and lubrication of parts. Special tools and procedures are required for some steps.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...dxem8295569
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure instructs assembling the travel motor components in the reverse order, noting proper installation of seals, lubricants, and alignment of parts.
Similar to Caterpillar cat 323 f ln excavator (prefix mfy) service repair manual (mfy00001 and up) (17)
John deere 230 cs chainsaws service repair manualdikskekmdmdm
This technical manual provides specifications and safety information for John Deere 200CS, 230CS, 300CS, and 550CS chainsaws. The manual is organized into sections covering general specifications, torque values, gasoline and oil specifications, and safety practices. Safety practices discussed include wearing protective equipment, handling chemicals and waste properly, and avoiding injury from rotating blades.
John deere 200 cs chainsaws service repair manualdikskekmdmdm
This technical manual provides specifications and safety information for John Deere 200CS, 230CS, 300CS, and 550CS chainsaws. It includes sections on general specifications, torque values, gasoline and oil recommendations, product identification numbers, and safety practices. The manual is intended as a reference for experienced technicians and contains detailed information organized by system.
John deere 200 sprayer attachment service repair manualdikskekmdmdm
This technical manual provides information on servicing a John Deere 200 Sprayer Attachment. It contains sections on specifications, component locations, schematics, theory of operation, troubleshooting, diagnostics, tests and adjustments, repair, and safety. The manual is intended for experienced technicians and provides all relevant information grouped by system to service that particular system.
John deere 54 inch commercial walk behind mower service repair manualdikskekmdmdm
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and safety information. The manual is intended for experienced technicians and covers engine, fuel, electrical, power train, steering, brake, and mower deck systems. Safety messages in the introduction emphasize the importance of following proper safety precautions when working on equipment.
John deere 51 & 246 rotary brooms service repair manualdikskekmdmdm
This technical manual provides specifications and lubrication information for John Deere lawn and grounds care equipment. It includes torque values, recommended gear case oils and greases, transmission fluids, and specifications for rotary mowers, snowblowers, and other attachments. The manual is intended to assist experienced technicians in servicing this equipment.
John deere 48, 450, 550 & 660 rotary tillers service repair manualdikskekmdmdm
This technical manual provides information for experienced technicians on inspecting, disassembling, and assembling various John Deere lawn and grounds care equipment including rotary mowers, snowblowers, snowthrowers, post hole diggers, rotary tillers, and rotary brooms with either 2000 or 540 RPM PTO. The manual is organized by equipment type and system and provides safety information for handling chemicals, high pressure fluids, batteries, and following other safe work procedures.
John deere 48, 50, 54, 60, 72, 76, 160, 172, 261 & 272 rotary mowers serv...dikskekmdmdm
This technical manual provides information for experienced technicians on inspecting, disassembling, and assembling various John Deere lawn and grounds care equipment including rotary mowers, snowblowers, snowthrowers, post hole diggers, rotary tillers, and rotary brooms with either 2000 or 540 RPM PTO. The manual is organized by equipment type and covers safety procedures, technical specifications, and repair instructions.
John deere 48 inch commercial walk behind mower service repair manualdikskekmdmdm
This technical manual provides service information for John Deere 38, 48, and 54-inch commercial walk-behind mowers. It contains specifications, repair and diagnostic procedures, and operational testing for the engine, fuel system, electrical system, power train, steering, brakes, mower deck, and other components. Safety messages are presented throughout and fastener torque specifications are provided. The manual is intended for experienced technicians and is part of John Deere's total product support program.
John deere 47, 59 & 359 snowblowers service repair manualdikskekmdmdm
This technical manual provides information for experienced technicians on inspecting, disassembling, and assembling various John Deere lawn and grounds care equipment including rotary mowers, snowblowers, snowthrowers, post hole diggers, rotary tillers, and rotary brooms with either 2000 or 540 RPM PTO. The manual is organized by equipment type and covers sections like safety procedures, fluid handling, battery handling, and service procedures.
John deere 46, 49 & 50 snowthrowers service repair manualdikskekmdmdm
This technical manual provides information for experienced technicians on inspecting, disassembling, and assembling various John Deere lawn and grounds care equipment including rotary mowers, snowblowers, snowthrowers, post hole diggers, rotary tillers, and rotary brooms with either 2000 or 540 RPM PTO. The manual is organized by equipment type and system and provides safety information for handling chemicals, high pressure fluids, batteries, and following other safe work procedures.
Clark gph 50 forklift service repair manualdikskekmdmdm
Planned maintenance is important for the long life and trouble-free operation of lift trucks. Regular inspections and lubrication on established intervals can help prevent major problems. Time intervals in maintenance manuals are based on operating hours and condition classifications like normal operation of 8 hours indoors or severe operation outdoors in dirty conditions. Records of inspections indicate maintenance needed to keep the truck safely operating as intended.
Clark gp127 e forklift service repair manualdikskekmdmdm
This document provides safety instructions for maintaining Clark industrial lift trucks. It discusses safety signs and messages, safe maintenance practices, and general shop precautions. Some key points include:
- Only trained personnel should maintain trucks according to manufacturer's recommendations.
- Properly ventilate work areas and keep floors dry. Avoid fire hazards.
- Before starting work, wear eye protection, raise drive wheels, disconnect power sources, and disconnect batteries when working on electrical systems.
- Close fuel valves before working on engine fuel systems. Test trucks only in safe areas.
Clark gp127 forklift service repair manualdikskekmdmdm
This document provides safety instructions for maintaining Clark industrial lift trucks. It discusses safety signs and messages, safe maintenance practices, and general shop precautions. Some key points include:
- Only trained personnel should maintain trucks according to manufacturer's recommendations.
- Properly ventilate work areas and keep floors dry. Avoid fire hazards.
- Before starting work, wear eye protection, raise drive wheels, disconnect power sources, and disconnect batteries when working on electrical systems.
- Close fuel valves before working on engine fuel systems. Test trucks only in safe areas.
Clark gex20 30 forklift service repair manualdikskekmdmdm
This document is the service manual for Clark Material Handling GEX 20-30 truck models. It provides information on maintenance and repair procedures organized into groups and sections. The manual consists of base modules that apply to all GEX 20-30 models as well as optional modules for specific truck configurations. It contains specifications, schematics, troubleshooting guides, and instructions for repairing or replacing components. Safety precautions are provided and users are instructed to read the operator's manual before working on the trucks.
Clark gcs standard forklift service repair manualdikskekmdmdm
This document provides safety guidelines and instructions for maintaining industrial lift trucks. It emphasizes that maintenance must be done by trained personnel according to the manufacturer's recommendations. Some key safety practices include properly ventilating the work area, avoiding fire hazards, raising the drive wheels before starting work, disconnecting batteries when working on electrical systems, and closing fuel valves before working on fuel systems. Following these procedures helps ensure safe maintenance of industrial lift trucks.
Clark g127 e forklift service repair manualdikskekmdmdm
This document provides safety instructions for maintaining Clark industrial lift trucks. It discusses safety signs and messages, safe maintenance practices, and general shop precautions. Some key points include:
- Only trained personnel should maintain trucks according to manufacturer's recommendations.
- Properly ventilate work areas and keep floors dry. Avoid fire hazards.
- Before starting work, wear eye protection, raise drive wheels, disconnect power sources, and disconnect batteries when working on electrical systems.
- Close fuel valves before working on engine fuel systems. Test trucks only in safe areas.
Clark g127 forklift service repair manualdikskekmdmdm
This document provides safety instructions for maintaining Clark industrial lift trucks. It discusses safety signs and messages, safe maintenance practices, and general shop precautions. Some key points include:
- Only trained personnel should maintain trucks according to manufacturer's recommendations.
- Properly ventilate work areas and keep floors dry. Avoid fire hazards.
- Before starting work, wear eye protection, raise drive wheels, disconnect power sources, and disconnect batteries when working on electrical systems.
- Close fuel valves before working on engine fuel systems. Test trucks only in safe areas.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323F EXCAVATOR MFY
Configuration: 323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
320F, 323F Excavators Machine Systems
Media Number -M0066628-06 Publication Date -01/09/2018 Date Updated -18/09/2018
i06225993
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Start By:
a. Remove the travel motor.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the
travel motor is 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the original position on the body of the travel
motor.
Illustration 1 g00510326
Note: During the removal of head (2) from the body of the travel motor, be careful not to
scratch or damage the mating surfaces of the components.
1/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 4. Remove socket head bolts (1).
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00510341
Illustration 3 g00510349
6. Turn over head (2).
7. Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head.
8. Remove the two check valve assemblies from the head.
Note: There is a retainer under spring (9). This retainer is a press fit in head (2). Do not
remove the retainer.
9. Insert a dowel rod with a small diameter into hole (X). Tap the dowel rod with a plastic
hammer in order to remove spring (9), poppet (8) and seat (7) from the head.
2/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00510351
10. Remove three fittings (10) and plugs (11) from the head. Remove the O-ring seal from each
fitting.
Illustration 5 g00510352
11. Remove three O-ring seals (12) and washer set (13) from the body of the travel motor.
12. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply
approximately 525 kPa (75 psi) of shop air pressure to brake release port (Y). Make sure
that the shop air pressure is free of water. Brake piston (14) will move up the piston guide,
and out of the piston guide. Remove brake piston (14) from the body of the travel motor.
Illustration 6 g00510353
3/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 13. Remove O-ring seal (15) from the brake piston. Remove backup ring (16) from the brake
piston.
14. Remove O-ring seal (17) from the brake piston. Remove backup ring (18) from the brake
piston.
Illustration 7 g00510356
15. Remove piston guide (19), five friction plates (20), and the four steel plates from the body
of the travel motor.
Illustration 8 g00510359
16. Remove O-ring seal (21) from the piston guide. Remove backup ring (22) from the piston
guide.
4/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g00510365
Note: Do not allow the components of barrel assembly (23) to come apart during the
removal from the travel motor. All of the components in the barrel assembly must be
reinstalled in the original location.
17. Use two large screwdrivers, as shown. Slowly remove barrel assembly (23) from the body
of the travel motor. Do not allow the components to fall apart.
Illustration 10 g00510502
Note: Shoe retainer (24) and piston shoe assemblies (25) are not serviced separately. Prior
to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put
identification marks on piston shoe assemblies (25) for assembly purposes. Identification
marks are used to identify the piston shoe assembly's location in shoe retainer (24) and
barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's
original bores in the shoe retainer and the barrel.
18. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the
piston shoe assemblies from the shoe retainer.
5/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00510504
19. Remove guide (27), spacer (28) and springs (29) from the barrel.
Illustration 12 g00510547
20. Remove cam plate (30) from the body of the travel motor.
Illustration 13 g00510550
21. Remove two keys (31) and the two locating pins (not shown) from the body of the travel
motor.
6/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00510551
22. Remove O-ring seal (33) from the body of the travel motor.
23. Use a soft faced hammer to remove shaft assembly (34) from the body of the travel motor.
Remove the shaft assembly in the direction that is indicated by the arrow. Refer to
Illustration 14.
Illustration 15 g00510595
24. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing
(36) with a press.
Illustration 16 g00510598
7/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 25. Remove inner race (37) from shaft (34).
Illustration 17 g00510599
26. Remove lip seal (38) from the body of the travel motor.
Illustration 18 g00510605
27. Remove two stoppers (39) and the two pistons from the body of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 17 16:06:10 UTC+0800 2020
8/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323F EXCAVATOR MFY
Configuration: 323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
320F, 323F Excavators Machine Systems
Media Number -M0066628-06 Publication Date -01/09/2018 Date Updated -18/09/2018
i07505849
Travel Motor - Disassemble
SMCS - 4351-015
S/N - MFY1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1P-2420 Transmission Repair Stand 1
FT-0957 Positioning Gp 4
B
- M16x2 Threaded Rod 3
8T-1757 Nut 6
9X-8268 Washer 6
C 421-5662 Lifting Eye Assembly 1
D 421-5663 Lifting Eye Assembly 2
E
1U-9895 Crossblock 1
3H-0465 Push-Puller Plate 2
8T-0298 Bolt 2
Start By:
a. Remove the travel motor.
1/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g06341880
1. Attach the travel motor to Tooling (A) and (B). The weight of the travel motor is
approximately 70 kg (154 lb).
2. Remove plugs (1) and the O-ring seals.
Illustration 2 g06344110
3. Remove plug (2) and the O-ring seal. Repeat for the opposite side.
Illustration 3 g06341912
2/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove plug (2A) and the O-ring seal. Repeat for the opposite side.
Illustration 4 g06341915
5. Remove spring (3).
Illustration 5 g06341917
6. Remove spool (4).
3/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 6 g06341942
Illustration 7 g06342000
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7. Remove bolts (5) and cap (6). Repeat for the opposite side.
8. Remove O-ring seal (10) from cap (6). Remove guide (9), spring (8), and washer (7) from
the head assembly. Repeat for the opposite side.
4/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 8 g06342005
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove plug (11), O-ring seal (12), spring (13), and ball (14) from cap (6). Repeat for the
other cap.
Illustration 9 g06342009
10. Remove spool (15).
5/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 10 g06343314
Illustration 11 g06343315
11. Remove relief valve (16). Remove O-ring seal (17) from relief valve (16).
12. Repeat for the opposite side.
Illustration 12 g06343359
6/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
13. Remove the nuts of Tooling (B). Remove bolts (19) from head assembly (18).
Illustration 13 g06343366
14. Use Tooling (C) and a suitable lifting device to remove head assembly (18). The weight of
head assembly (18) is approximately 21 kg (47 lb).
Illustration 14 g06343374
15. Remove control plate (20) and bearing (21) from head assembly (18).
7/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 15 g06343381
16. Remove pins (22) and springs (23).
17. Remove O-ring seals (24) and (25).
Illustration 16 g06343383
18. Use Tooling (D) and a suitable lifting device to remove housing assembly (26) from
Tooling (A) and place on a suitable bench.
Illustration 17 g06343417
8/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. To avoid personal injury, always wear eye and face protection when
using pressurized air.
19. Attach Tooling (E) to housing (26). Use air pressure to unseat brake piston (27). Remove
Tooling (E) and brake piston (27).
Illustration 18 g06343437
20. Remove back up rings (28) and O-ring seals (29) from brake piston (27).
Illustration 19 g06343462
21. Remove brake piston guide (30).
9/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 20 g06343464
22. Remove O-ring seal (31) from brake piston guide (30).
Illustration 21 g06343466
Illustration 22 g06343469
Note: Note the orientation of friction discs (32) and plates (33) for assembly purposes.
23. Remove friction discs (32) and plates (33).
10/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M0...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 23 g06343638
24. Remove rotating group (34) from housing (26).
Illustration 24 g06343777
25. Remove pistons (35) and retainer (36) from barrel (37).
Illustration 25 g06343783
26. Remove hold down ball (38) and springs (39) from barrel (37).
11/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M0...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 29 g06343795
30. Remove balls (46).
31. Remove bearing (44) and lip seal (45).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 17 16:07:09 UTC+0800 2020
13/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M0...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323F EXCAVATOR MFY
Configuration: 323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
320F, 323F Excavators Machine Systems
Media Number -M0066628-06 Publication Date -01/09/2018 Date Updated -18/09/2018
i06225999
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp. 1
B - Loctite Low Breakloose PST -
C - Loctite 242 -
D - O-ring Assembly Compound -
E - Molybdenum Grease -
1. Make sure that all of the components of the travel motor are thoroughly clean and free of
dirt and debris prior to assembly.
1/10
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 1 g00510595
2. Install retaining ring (35) in the groove on shaft (34).
3. Install bearing (36) on shaft (34) with a press. Install the bearing until the bearing contacts
the retaining ring.
4. Install the other retaining ring on the opposite side of bearing (36).
Illustration 2 g00510598
5. Install inner race (37) on the end of shaft (34) until the inner race is seated against the
shoulder on the shaft.
Illustration 3 g00651891
(a) Body
6. Apply Tooling (B) on Surfaces (Y) of the body of the travel motor.
7. Use Tooling (A) in order to install lip seal (38).
2/10
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 8. Install lip type seal (38) in the body of the travel motor. Install the lip seal so that the sealing
lip is facing in the direction that is shown. Make sure that the lip seal contacts the
counterbore in the body of the travel motor.
Note: Slowly rotate shaft assembly (34) during the installation in order to make sure that the
shaft assembly does not bind in the body of the travel motor.
9. Apply clean hydraulic oil on the lip of lip seal (38).
10. Use a press to install shaft assembly (34) in the body of the travel motor. Slowly rotate the
shaft during the installation in order to make sure that the shaft does not bind. Make sure
that the bearing on the shaft contacts the counterbore in the body of the travel motor.
Illustration 4 g00651960
NOTICE
The locating pin on each key is not centered. In order to prevent
damage to the barrel assembly during assembly of the travel motor, the
keys must be installed as shown. Also, the keys must be installed in the
key's original location in the body of the travel motor.
11. Install the two locating pins and two keys (31) in the body of the travel motor, as shown.
3/10
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 5 g00510547
12. Install cam plate (30) in the body of the travel motor in the original location. Make sure that
the two pistons and two keys (31) in the body of the travel motor engage properly with the
cam plate.
Illustration 6 g00510504
13. Install nine springs (29) in the barrel. Install spacer (28) and guide (27) on the barrel.
Illustration 7 g00878253
14. Install piston shoe assemblies (25) in the original bores in shoe retainer (24).
4/10
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...