The document provides disassembly instructions for a travel motor in 3 steps or less:
1. Thoroughly clean and secure the travel motor before removing components like the head, springs, plates, and seals.
2. Use tools and air pressure to carefully remove additional internal parts such as the brake piston, friction discs, and rotating group.
3. The final components that can be removed are the pistons, retainer, and hold down springs from the barrel of the motor.
Caterpillar cat 323 f excavator (prefix mfy) service repair manual (mfy00001 ...jfdskekdmme
This document provides disassembly instructions for a 323F and 323F LN excavator travel motor in 27 steps. It details removing components such as the head assembly, housing assembly, brake piston, friction discs, and rotating group. Proper tooling is required and safety precautions should be followed when releasing spring forces or using pressurized air. The travel motor must be thoroughly cleaned and components reinstalled in their original positions and orientations.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...cdsaas
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly process reverses the disassembly steps and includes applying sealant and pressing components together using various tools.
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Caterpillar cat 319 d l excavator (prefix ayf) service repair manual (ayf0000...fjkskedmme
The document provides instructions for disassembling and assembling the final drive of a 319D L excavator. It lists 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. It then lists 29 steps for assembly, reinstalling those components in reverse order and noting that cleanliness is important, O-rings and seals should be replaced, and bearings should be preloaded to determine the correct shim thickness. The procedure involves using various tools to separate, lift, and install parts carefully due to their weights.
Caterpillar cat 349 d l excavator (prefix pzg) service repair manual (pzg0000...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, disks, seals and pins. It then lists 28 steps for assembly, installing components like washers, spacers, seals and the piston in reverse order of disassembly. Precautions are provided to keep parts clean and properly identify components to ensure correct reassembly.
Caterpillar cat 349 e l excavator (prefix etc) service repair manual (etc0000...cdsaas
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque is required for all bolts.
Caterpillar cat 349 e excavator (prefix spg) service repair manual (spg00001 ...cdsaas
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves removing 27 individual components from the motor housing, rotating group, and brake housing. The assembly process describes installing the components in reverse order and includes specifications for various parts. Proper lubrication and torque specifications are noted throughout.
Caterpillar cat 349 d excavator (prefix nnf) service repair manual (nnf00001 ...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, disks, seals and more. It then lists 28 steps for assembly, installing components like seals, spacers, washers, pistons and plugs in the reverse order of disassembly. Precautions are provided to keep parts clean and properly identify components to ensure correct reassembly.
Caterpillar cat 323 f excavator (prefix mfy) service repair manual (mfy00001 ...jfdskekdmme
This document provides disassembly instructions for a 323F and 323F LN excavator travel motor in 27 steps. It details removing components such as the head assembly, housing assembly, brake piston, friction discs, and rotating group. Proper tooling is required and safety precautions should be followed when releasing spring forces or using pressurized air. The travel motor must be thoroughly cleaned and components reinstalled in their original positions and orientations.
Caterpillar cat 349 e l excavator (prefix tfg) service repair manual (tfg0000...cdsaas
1) The document provides step-by-step instructions for disassembling and assembling the hydraulic fan drive of a 349E L excavator.
2) The disassembly process involves removing 22 components including bolts, seals, plates, and housing pieces.
3) The assembly process reverses the disassembly steps and includes applying sealant and pressing components together using various tools.
This document provides instructions for removing and installing various engine components on a Caterpillar 349D2 excavator, including:
1. Removing and installing the rear gear group, which involves removing several gears, seals, bolts and bearings.
2. Removing the flywheel using lifting equipment and tools.
3. Installing the flywheel and ensuring it is properly seated.
4. Removing and installing the crankshaft rear seal using bolts and following inspection procedures.
Caterpillar cat 319 d l excavator (prefix ayf) service repair manual (ayf0000...fjkskedmme
The document provides instructions for disassembling and assembling the final drive of a 319D L excavator. It lists 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. It then lists 29 steps for assembly, reinstalling those components in reverse order and noting that cleanliness is important, O-rings and seals should be replaced, and bearings should be preloaded to determine the correct shim thickness. The procedure involves using various tools to separate, lift, and install parts carefully due to their weights.
Caterpillar cat 349 d l excavator (prefix pzg) service repair manual (pzg0000...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, disks, seals and pins. It then lists 28 steps for assembly, installing components like washers, spacers, seals and the piston in reverse order of disassembly. Precautions are provided to keep parts clean and properly identify components to ensure correct reassembly.
Caterpillar cat 349 e l excavator (prefix etc) service repair manual (etc0000...cdsaas
This document provides instructions for removing and installing an air control valve on a Caterpillar C13 engine. The removal procedure involves disconnecting hoses and tubes, removing bolts, and separating housing components. The installation procedure is the reverse of removal. Proper torque is required for all bolts.
Caterpillar cat 349 e excavator (prefix spg) service repair manual (spg00001 ...cdsaas
This document provides instructions for disassembling and assembling the travel motor on 349E and 349E L excavator models. The disassembly process involves removing 27 individual components from the motor housing, rotating group, and brake housing. The assembly process describes installing the components in reverse order and includes specifications for various parts. Proper lubrication and torque specifications are noted throughout.
Caterpillar cat 349 d excavator (prefix nnf) service repair manual (nnf00001 ...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, disks, seals and more. It then lists 28 steps for assembly, installing components like seals, spacers, washers, pistons and plugs in the reverse order of disassembly. Precautions are provided to keep parts clean and properly identify components to ensure correct reassembly.
Caterpillar cat 349 d2 l excavator (prefix yag) service repair manual (yag000...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pistons, and housing. Precautions are outlined to prevent contamination and ensure proper installation of parts in their original locations. The assembly section instructs installation of components in reverse order and includes applying sealant and lubricant.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 27 steps for assembly, installing components like seals, pistons, housing, plates and head in reverse order of disassembly. Tools required are listed in tables. Cautions are provided about cleaning parts and preventing contamination of hydraulic systems.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, replacing components in reverse order and noting to keep parts clean to prevent contamination of the hydraulic system. Precise measurements and proper orientation of parts like washers is emphasized for correct reassembly.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...cdsaas
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 e excavator (prefix rgh) service repair manual (rgh00001 ...cdsaas
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Precise torques and specifications are provided for correct installation of components.
Caterpillar cat 349 d excavator (prefix men) service repair manual (men00001 ...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 13 steps for assembly, including installing seals, spacers, pistons, housing, and tightening components. Required tools include eyebolts, pullers, drivers, and seals. Cleanliness is emphasized to prevent contamination of hydraulic components.
The document provides instructions for disassembling and assembling a travel motor. It lists 30 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 31 steps for assembly, reinstalling these components in reverse order. Precautions are given to prevent contamination and ensure proper installation of parts like O-rings, seals, and pins in their original locations. Tools required are listed in a table.
Caterpillar cat 349 d2 l excavator (prefix zae) service repair manual (zae000...cdsaas
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a C13 engine. The removal procedure involves using various tools to remove 11 components in 9 steps. The installation procedure involves preparing and installing 14 components in 12 steps, ensuring proper dimensions and torque specifications are followed. Proper cleaning and use of locking compounds is emphasized.
Caterpillar cat 349 d2 l excavator (prefix xac) service repair manual (xac000...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, housing keys and more. It then lists 13 steps for assembly, replacing components in reverse order and noting to clean all parts, apply lubricant, and ensure proper orientation of washers and spacers. Tools required are listed for both disassembly and assembly processes.
Caterpillar cat 349 f l excavator (prefix bz2) service repair manual (bz20000...fjsjjekdkme
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy. Diagrams illustrate each step for clarifying proper disassembly procedures.
Caterpillar cat 323 f ln excavator (prefix mfy) service repair manual (mfy000...jfdskekdmme
The document provides disassembly instructions for a travel motor in 3 sentences:
It begins by instructing the removal of the travel motor and cleaning of its exterior. Detailed steps are then given to disassemble the various components of the travel motor by removing fasteners, seals, plates, springs, and other parts. Precautions are included to safely release stored spring energy during disassembly.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...djdksmmdmd
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, ensuring proper alignment and lubrication of parts.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, applying specified lubricants and ensuring proper alignment of parts.
Caterpillar cat 325 f l excavator (prefix yca) service repair manual (yca0000...dikskedmdm
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...shun96145luo
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, ensuring proper alignment and lubrication of parts. Special tools and procedures are required for some steps.
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and keys in their proper positions and applying sealant and grease as needed. The goal is to take the travel motor fully apart and then rebuild it correctly with all components returned to their original locations.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...f7useijdkdmd1
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and ensuring keys and pins are in their proper positions. The goal is to take the travel motor apart piece by piece and then rebuild it correctly during assembly.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...fjdkksmemd
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...f7siejdkdmd
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and ensuring keys and pins are in their proper positions. The goal is to take the travel motor apart piece by piece and then rebuild it correctly during assembly.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 325F LCR. It describes 25 steps to disassemble the various components of the travel motor by removing seals, plates, pistons, springs and other parts. It then describes 11 steps for reassembling the components, including installing seals, bearings, pins and keys in the proper positions and applying grease or sealant as needed. Precise positioning of parts is emphasized for correct reassembly.
Caterpillar cat 349 d2 l excavator (prefix yag) service repair manual (yag000...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It lists the required tools and gives step-by-step instructions to remove components such as the head, plates, seals, pistons, and housing. Precautions are outlined to prevent contamination and ensure proper installation of parts in their original locations. The assembly section instructs installation of components in reverse order and includes applying sealant and lubricant.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 27 steps for assembly, installing components like seals, pistons, housing, plates and head in reverse order of disassembly. Tools required are listed in tables. Cautions are provided about cleaning parts and preventing contamination of hydraulic systems.
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, replacing components in reverse order and noting to keep parts clean to prevent contamination of the hydraulic system. Precise measurements and proper orientation of parts like washers is emphasized for correct reassembly.
Caterpillar cat 349 e excavator (prefix fjb) service repair manual (fjb00001 ...cdsaas
This document provides instructions for disassembling and assembling the hydraulic fan drive of a 349E excavator. The disassembly process involves removing 22 components in sequential order, taking care to note locations and orientations. Assembly is the reverse of disassembly, applying sealant and torque specifications as indicated. Precision and cleanliness are important to prevent damage to components.
Caterpillar cat 349 e excavator (prefix rgh) service repair manual (rgh00001 ...cdsaas
This document provides instructions for disassembling and assembling the travel motor on a 349E excavator. The disassembly process includes 27 steps to remove components like the head assembly, brake housing, rotating group, barrel assembly and more. The assembly process reverses the disassembly with 13 steps like installing seals, springs, pistons and plates in the proper order and orientation. Precise torques and specifications are provided for correct installation of components.
Caterpillar cat 349 d excavator (prefix men) service repair manual (men00001 ...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 13 steps for assembly, including installing seals, spacers, pistons, housing, and tightening components. Required tools include eyebolts, pullers, drivers, and seals. Cleanliness is emphasized to prevent contamination of hydraulic components.
The document provides instructions for disassembling and assembling a travel motor. It lists 30 steps for disassembly, removing components like the head, plates, seals, pistons, and housing. It then lists 31 steps for assembly, reinstalling these components in reverse order. Precautions are given to prevent contamination and ensure proper installation of parts like O-rings, seals, and pins in their original locations. Tools required are listed in a table.
Caterpillar cat 349 d2 l excavator (prefix zae) service repair manual (zae000...cdsaas
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a C13 engine. The removal procedure involves using various tools to remove 11 components in 9 steps. The installation procedure involves preparing and installing 14 components in 12 steps, ensuring proper dimensions and torque specifications are followed. Proper cleaning and use of locking compounds is emphasized.
Caterpillar cat 349 d2 l excavator (prefix xac) service repair manual (xac000...cdsaas
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, housing keys and more. It then lists 13 steps for assembly, replacing components in reverse order and noting to clean all parts, apply lubricant, and ensure proper orientation of washers and spacers. Tools required are listed for both disassembly and assembly processes.
Caterpillar cat 349 f l excavator (prefix bz2) service repair manual (bz20000...fjsjjekdkme
The document provides step-by-step instructions to disassemble a travel motor on an excavator model 349F L. It details 27 steps to remove components such as plugs, seals, springs, pistons, plates, and housings. Safety precautions are provided to wear protective equipment when removing parts with stored spring energy. Diagrams illustrate each step for clarifying proper disassembly procedures.
Caterpillar cat 323 f ln excavator (prefix mfy) service repair manual (mfy000...jfdskekdmme
The document provides disassembly instructions for a travel motor in 3 sentences:
It begins by instructing the removal of the travel motor and cleaning of its exterior. Detailed steps are then given to disassemble the various components of the travel motor by removing fasteners, seals, plates, springs, and other parts. Precautions are included to safely release stored spring energy during disassembly.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...djdksmmdmd
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, ensuring proper alignment and lubrication of parts.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, applying specified lubricants and ensuring proper alignment of parts.
Caterpillar cat 325 f l excavator (prefix yca) service repair manual (yca0000...dikskedmdm
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...shun96145luo
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, ensuring proper alignment and lubrication of parts. Special tools and procedures are required for some steps.
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and keys in their proper positions and applying sealant and grease as needed. The goal is to take the travel motor fully apart and then rebuild it correctly with all components returned to their original locations.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...f7useijdkdmd1
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and ensuring keys and pins are in their proper positions. The goal is to take the travel motor apart piece by piece and then rebuild it correctly during assembly.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...fjdkksmemd
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, with notes to ensure proper alignment and installation of keys and seals.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...f7siejdkdmd
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and ensuring keys and pins are in their proper positions. The goal is to take the travel motor apart piece by piece and then rebuild it correctly during assembly.
The document provides instructions for disassembling and assembling the travel motor of an excavator model 325F LCR. It describes 25 steps to disassemble the various components of the travel motor by removing seals, plates, pistons, springs and other parts. It then describes 11 steps for reassembling the components, including installing seals, bearings, pins and keys in the proper positions and applying grease or sealant as needed. Precise positioning of parts is emphasized for correct reassembly.
Caterpillar cat 325 f lcr excavator (prefix yca) service repair manual (yca00...dikskedmdm
The document provides instructions for disassembling and assembling the travel motor of a 325F LCR excavator. It describes 25 steps to disassemble the travel motor by removing components like the head, fittings, plates, seals, pistons, and shaft. It then describes 11 steps for assembling the travel motor, including installing seals, bearings, springs, and ensuring keys and pins are in their proper positions. The goal is to take the travel motor apart piece by piece and then rebuild it correctly during assembly.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence, taking care to mark parts for proper reinstallation.
3. The assembly procedure instructs assembling the travel motor components in the reverse order, applying specified lubricants and fasteners, and using tools as needed.
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure involves installing the components in the reverse order, ensuring proper alignment and lubrication of parts. Special tools and procedures are required for some steps.
Caterpillar Cat 325F L Excavator (Prefix YCA) Service Repair Manual (YCA00001...dxem8295569
1. The document provides step-by-step instructions for disassembling and assembling the travel motor of an excavator model 325F LCR.
2. The disassembly procedure involves removing 24 components from the travel motor in a specific sequence.
3. The assembly procedure instructs assembling the travel motor components in the reverse order, noting proper installation of seals, lubricants, and alignment of parts.
Similar to Caterpillar cat 323 f excavator (prefix mfy) service repair manual (mfy00001 and up) (16)
Caterpillar cat m315 c wheeled excavator (prefix h2b) service repair manual (...jfdjskmdmme
The document provides instructions for disassembling the piston pump of a M315C wheeled excavator. It describes removing 31 individual parts from the pump in a specific sequence, including the servo valve, charge pump, gears, head, relief valves, pistons, barrel assembly, swashplate assembly, and other components. Cleanliness is important during disassembly to prevent dirt from entering the internal mechanisms. Personal injury can result from hydraulic pressure still remaining in the system, so precautions are described.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...jfdjskmdmme
This document provides instructions for disassembling and assembling the main hydraulic pump of a M315C wheeled excavator. It lists 42 steps to disassemble the pump by removing components like valves, springs, seals, pistons, and bearings. It then lists the assembly steps in reverse order, noting to clean parts and apply new thread lock before reinstalling components. Precautions are provided to mark parts for orientation and contain fluids during maintenance.
Caterpillar cat 330 d2 l excavator (prefix xdr) service repair manual (xdr000...jfdjskmdmme
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 330 d2 l excavator (prefix hsp) service repair manual (hsp000...jfdjskmdmme
The document provides instructions for disassembling a 330D2 excavator travel motor. It is a 28 step process that includes removing components like the motor head, brake piston, rotating assembly, cam plate, piston assemblies and seals. Special tools are required for tasks like removing retaining rings and bearing races. Technicians are advised to mark components for proper reinstallation and contain any fluids during disassembly.
Caterpillar cat 330 d2 l excavator (prefix her) service repair manual (her000...jfdjskmdmme
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex000...jfdjskmdmme
The document provides instructions for disassembling a final drive assembly in 3 steps:
1. Remove the final drive assembly and disassemble it by removing the cover, gears, carrier assembly, planetary gears, and ring gear.
2. Disassemble the planetary carrier by removing the planetary shafts, washers, and gears.
3. Remove the ring gear from the sprocket housing and disassemble the motor housing by removing coupling gear, shims, and seals.
Caterpillar cat 330 d2 l excavator (prefix ex7) service repair manual (ex7000...jfdjskmdmme
The document provides instructions for disassembling and assembling a travel motor. It is a service repair manual for Caterpillar 330D2 and 330D2 L excavators. The disassembly procedure involves removing 28 different parts from the travel motor in 27 steps. The assembly procedure involves installing the parts in the reverse order over 23 steps. Precise alignment and cleanliness of parts is emphasized to ensure proper function of the travel motor.
Caterpillar cat 330 d2 l excavator (prefix ebp) service repair manual (ebp000...jfdjskmdmme
The document provides instructions for disassembling an excavator travel motor. It begins by having the technician remove the travel motor from the excavator. The disassembly instructions then detail 27 steps to fully disassemble the travel motor. These include removing components like the motor head, brake piston, barrel assembly, cam plate, and shaft assembly. Throughout the process, technicians are warned to take care with components and contain any fluids.
Caterpillar cat 330 d2 l excavator (prefix dtg) service repair manual (dtg000...jfdjskmdmme
The document provides the disassembly procedure for a 330D2 excavator travel motor in 28 steps. It begins by instructing the technician to clean and secure the travel motor vertically, then remove the head by taking out bolts and marking parts for reassembly. Several internal components are then removed, including brake pistons, plates, and seals. The rotating assembly is separated from the housing using a prybar. Bearings and seals are removed from the shaft. Finally, the cam plate, pistons, seals and other remaining parts are disassembled from the housing. Throughout, precise steps and illustrations are provided to guide disassembly while maintaining part orientation.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
The document provides instructions for disassembling a 330D2 excavator travel motor. It is a 28 step process that includes removing components like the motor head, brake piston, rotating assembly, cam plate, piston assemblies and seals. Special tools are required for tasks like removing retaining rings and bearing races. Technicians are advised to mark components for proper reinstallation and contain any fluids removed from the motor.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves removing 37 individual parts in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on setting the bearing preload and installing seals correctly.
The document provides instructions for disassembling a final drive assembly in 3 steps:
1. Remove the final drive assembly and disassemble it by removing the cover, gears, carrier assembly, planetary gears, and ring gear.
2. Disassemble the planetary carrier by removing the planetary shafts, washers, and gears.
3. Remove the ring gear from the sprocket housing and disassemble the motor housing by removing coupling gear, shims, and seals.
The document provides instructions for disassembling and assembling a travel motor. It is a service repair manual for Caterpillar 330D2 and 330D2 L excavators. The disassembly procedure involves removing 28 different parts from the travel motor in 27 steps. The assembly procedure reverses this process and puts the travel motor back together in 25 steps, reinstalling the parts in the reverse order that they were removed. Precise instructions are given for each step to ensure correct reassembly.
The document provides disassembly instructions for a 330D2 and 330D2 L excavator travel motor in 28 steps. It begins by having the technician thoroughly clean and secure the travel motor vertically before disassembling. The steps then carefully describe removing components like the head, brake piston, plates, seals, bearings, and more. Pictures accompany each step to illustrate the proper procedure. Safety notices are included to handle fluids and springs carefully.
The document provides the disassembly procedure for a 330D2 excavator travel motor. It lists 28 steps to fully disassemble the travel motor, including removing the head, brake piston, plates and discs, rotating assembly, seals, and other internal components. Tools required are also listed. The procedure aims to clearly identify each part and ensure proper reinstallation of components in their original positions and orientations.
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...jfdjskmdmme
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a 330D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and covers. Precautions are listed to keep parts clean and prevent damage. The installation procedure specifies how to position gears, bearings, seals and other components, applying threadlock and noting torque specifications. Dimensions and angles are provided to ensure proper installation of bearings.
Caterpillar cat 330 d l excavator (prefix thj) service repair manual (thj0000...jfdjskmdmme
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. This includes removing covers, gears, shafts, bearings, seals and other components. Special tools are required to remove some parts, and safety notes are provided about cleanliness and part weights which require multiple people to handle. The overall goal is to break the final drive down into all of its individual parts for repair or replacement.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...jfdjskmdmme
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations supplement the written instructions.
3. Proper cleaning and application of sealant or retaining compound is emphasized to prevent contamination and ensure proper component life.
Caterpillar cat 330 d l excavator (prefix nbd) service repair manual (nbd0000...jfdjskmdmme
The document provides disassembly instructions for a final drive on an excavator model 330D L excavator. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing the cover, gears, plates, plugs, seals, carrier assembly, planetary gear assembly, shafts, springs, and bearings. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323F EXCAVATOR MFY
Configuration: 323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
320F, 323F Excavators Machine Systems
Media Number -M0066628-06 Publication Date -01/09/2018 Date Updated -18/09/2018
i06225993
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Start By:
a. Remove the travel motor.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the
travel motor is 60 kg (132 lb).
3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the original position on the body of the travel
motor.
Illustration 1 g00510326
Note: During the removal of head (2) from the body of the travel motor, be careful not to
scratch or damage the mating surfaces of the components.
1/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 4. Remove socket head bolts (1).
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00510341
Illustration 3 g00510349
6. Turn over head (2).
7. Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head.
8. Remove the two check valve assemblies from the head.
Note: There is a retainer under spring (9). This retainer is a press fit in head (2). Do not
remove the retainer.
9. Insert a dowel rod with a small diameter into hole (X). Tap the dowel rod with a plastic
hammer in order to remove spring (9), poppet (8) and seat (7) from the head.
2/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00510351
10. Remove three fittings (10) and plugs (11) from the head. Remove the O-ring seal from each
fitting.
Illustration 5 g00510352
11. Remove three O-ring seals (12) and washer set (13) from the body of the travel motor.
12. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply
approximately 525 kPa (75 psi) of shop air pressure to brake release port (Y). Make sure
that the shop air pressure is free of water. Brake piston (14) will move up the piston guide,
and out of the piston guide. Remove brake piston (14) from the body of the travel motor.
Illustration 6 g00510353
3/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 13. Remove O-ring seal (15) from the brake piston. Remove backup ring (16) from the brake
piston.
14. Remove O-ring seal (17) from the brake piston. Remove backup ring (18) from the brake
piston.
Illustration 7 g00510356
15. Remove piston guide (19), five friction plates (20), and the four steel plates from the body
of the travel motor.
Illustration 8 g00510359
16. Remove O-ring seal (21) from the piston guide. Remove backup ring (22) from the piston
guide.
4/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 9 g00510365
Note: Do not allow the components of barrel assembly (23) to come apart during the
removal from the travel motor. All of the components in the barrel assembly must be
reinstalled in the original location.
17. Use two large screwdrivers, as shown. Slowly remove barrel assembly (23) from the body
of the travel motor. Do not allow the components to fall apart.
Illustration 10 g00510502
Note: Shoe retainer (24) and piston shoe assemblies (25) are not serviced separately. Prior
to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put
identification marks on piston shoe assemblies (25) for assembly purposes. Identification
marks are used to identify the piston shoe assembly's location in shoe retainer (24) and
barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's
original bores in the shoe retainer and the barrel.
18. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the
piston shoe assemblies from the shoe retainer.
5/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00510504
19. Remove guide (27), spacer (28) and springs (29) from the barrel.
Illustration 12 g00510547
20. Remove cam plate (30) from the body of the travel motor.
Illustration 13 g00510550
21. Remove two keys (31) and the two locating pins (not shown) from the body of the travel
motor.
6/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00510551
22. Remove O-ring seal (33) from the body of the travel motor.
23. Use a soft faced hammer to remove shaft assembly (34) from the body of the travel motor.
Remove the shaft assembly in the direction that is indicated by the arrow. Refer to
Illustration 14.
Illustration 15 g00510595
24. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing
(36) with a press.
Illustration 16 g00510598
7/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 25. Remove inner race (37) from shaft (34).
Illustration 17 g00510599
26. Remove lip seal (38) from the body of the travel motor.
Illustration 18 g00510605
27. Remove two stoppers (39) and the two pistons from the body of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 17 16:06:10 UTC+0800 2020
8/8
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323F EXCAVATOR MFY
Configuration: 323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
320F, 323F Excavators Machine Systems
Media Number -M0066628-06 Publication Date -01/09/2018 Date Updated -18/09/2018
i07505849
Travel Motor - Disassemble
SMCS - 4351-015
S/N - MFY1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1P-2420 Transmission Repair Stand 1
FT-0957 Positioning Gp 4
B
- M16x2 Threaded Rod 3
8T-1757 Nut 6
9X-8268 Washer 6
C 421-5662 Lifting Eye Assembly 1
D 421-5663 Lifting Eye Assembly 2
E
1U-9895 Crossblock 1
3H-0465 Push-Puller Plate 2
8T-0298 Bolt 2
Start By:
a. Remove the travel motor.
1/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g06341880
1. Attach the travel motor to Tooling (A) and (B). The weight of the travel motor is
approximately 70 kg (154 lb).
2. Remove plugs (1) and the O-ring seals.
Illustration 2 g06344110
3. Remove plug (2) and the O-ring seal. Repeat for the opposite side.
Illustration 3 g06341912
2/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Remove plug (2A) and the O-ring seal. Repeat for the opposite side.
Illustration 4 g06341915
5. Remove spring (3).
Illustration 5 g06341917
6. Remove spool (4).
3/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 6 g06341942
Illustration 7 g06342000
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7. Remove bolts (5) and cap (6). Repeat for the opposite side.
8. Remove O-ring seal (10) from cap (6). Remove guide (9), spring (8), and washer (7) from
the head assembly. Repeat for the opposite side.
4/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 8 g06342005
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
9. Remove plug (11), O-ring seal (12), spring (13), and ball (14) from cap (6). Repeat for the
other cap.
Illustration 9 g06342009
10. Remove spool (15).
5/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 10 g06343314
Illustration 11 g06343315
11. Remove relief valve (16). Remove O-ring seal (17) from relief valve (16).
12. Repeat for the opposite side.
Illustration 12 g06343359
6/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
13. Remove the nuts of Tooling (B). Remove bolts (19) from head assembly (18).
Illustration 13 g06343366
14. Use Tooling (C) and a suitable lifting device to remove head assembly (18). The weight of
head assembly (18) is approximately 21 kg (47 lb).
Illustration 14 g06343374
15. Remove control plate (20) and bearing (21) from head assembly (18).
7/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 15 g06343381
16. Remove pins (22) and springs (23).
17. Remove O-ring seals (24) and (25).
Illustration 16 g06343383
18. Use Tooling (D) and a suitable lifting device to remove housing assembly (26) from
Tooling (A) and place on a suitable bench.
Illustration 17 g06343417
8/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. To avoid personal injury, always wear eye and face protection when
using pressurized air.
19. Attach Tooling (E) to housing (26). Use air pressure to unseat brake piston (27). Remove
Tooling (E) and brake piston (27).
Illustration 18 g06343437
20. Remove back up rings (28) and O-ring seals (29) from brake piston (27).
Illustration 19 g06343462
21. Remove brake piston guide (30).
9/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 20 g06343464
22. Remove O-ring seal (31) from brake piston guide (30).
Illustration 21 g06343466
Illustration 22 g06343469
Note: Note the orientation of friction discs (32) and plates (33) for assembly purposes.
23. Remove friction discs (32) and plates (33).
10/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M0...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 23 g06343638
24. Remove rotating group (34) from housing (26).
Illustration 24 g06343777
25. Remove pistons (35) and retainer (36) from barrel (37).
Illustration 25 g06343783
26. Remove hold down ball (38) and springs (39) from barrel (37).
11/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M0...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 29 g06343795
30. Remove balls (46).
31. Remove bearing (44) and lip seal (45).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Aug 17 16:07:09 UTC+0800 2020
13/13
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M0...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323F EXCAVATOR MFY
Configuration: 323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
320F, 323F Excavators Machine Systems
Media Number -M0066628-06 Publication Date -01/09/2018 Date Updated -18/09/2018
i06225999
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp. 1
B - Loctite Low Breakloose PST -
C - Loctite 242 -
D - O-ring Assembly Compound -
E - Molybdenum Grease -
1. Make sure that all of the components of the travel motor are thoroughly clean and free of
dirt and debris prior to assembly.
1/10
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 1 g00510595
2. Install retaining ring (35) in the groove on shaft (34).
3. Install bearing (36) on shaft (34) with a press. Install the bearing until the bearing contacts
the retaining ring.
4. Install the other retaining ring on the opposite side of bearing (36).
Illustration 2 g00510598
5. Install inner race (37) on the end of shaft (34) until the inner race is seated against the
shoulder on the shaft.
Illustration 3 g00651891
(a) Body
6. Apply Tooling (B) on Surfaces (Y) of the body of the travel motor.
7. Use Tooling (A) in order to install lip seal (38).
2/10
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 8. Install lip type seal (38) in the body of the travel motor. Install the lip seal so that the sealing
lip is facing in the direction that is shown. Make sure that the lip seal contacts the
counterbore in the body of the travel motor.
Note: Slowly rotate shaft assembly (34) during the installation in order to make sure that the
shaft assembly does not bind in the body of the travel motor.
9. Apply clean hydraulic oil on the lip of lip seal (38).
10. Use a press to install shaft assembly (34) in the body of the travel motor. Slowly rotate the
shaft during the installation in order to make sure that the shaft does not bind. Make sure
that the bearing on the shaft contacts the counterbore in the body of the travel motor.
Illustration 4 g00651960
NOTICE
The locating pin on each key is not centered. In order to prevent
damage to the barrel assembly during assembly of the travel motor, the
keys must be installed as shown. Also, the keys must be installed in the
key's original location in the body of the travel motor.
11. Install the two locating pins and two keys (31) in the body of the travel motor, as shown.
3/10
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 5 g00510547
12. Install cam plate (30) in the body of the travel motor in the original location. Make sure that
the two pistons and two keys (31) in the body of the travel motor engage properly with the
cam plate.
Illustration 6 g00510504
13. Install nine springs (29) in the barrel. Install spacer (28) and guide (27) on the barrel.
Illustration 7 g00878253
14. Install piston shoe assemblies (25) in the original bores in shoe retainer (24).
4/10
323F LN Excavator MFY00001-UP (MACHINE) POWERED BY C4.4 Engine(M008...
2020/8/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...