This document provides installation instructions for removing and installing a crankshaft front seal on a 323 excavator. It outlines 20 steps to remove the existing seal using a specialty tool. These include removing bolts, gears, and other components to access the seal. It then describes 11 steps to carefully install a new seal, aligning parts and torquing bolts to the specified values. Proper cleaning and protection from contamination are emphasized throughout.
This document provides installation instructions for a rear power takeoff (RPTO) on a 323 excavator with a C7.1 engine. It involves cleaning components, pressing bearings into housings, aligning gears and idler hubs, lubricating and installing components, and tightening bolts to specified torques. The instructions also cover removing and installing the crankshaft pulley assembly and front seal.
Caterpillar cat 329 d l excavator (prefix wdk) service repair manual (wdk0000...ufjsjekfksemm
This document provides removal and assembly procedures for a travel motor on Caterpillar 329D and 329D L excavators. The removal procedure involves draining fluid, disconnecting hoses, removing bolts and pulling the travel motor out of the final drive. Disassembly of the travel motor requires removing the head, port plate, bearings, seals, springs, brake piston and various other internal components using specialized tools. The assembly procedure instructs to replace all seals and gaskets, clean all parts thoroughly, and install components in reverse order of removal while applying a film of oil. Proper cleanliness and torque specifications are emphasized throughout.
Caterpillar cat 319 d l excavator (prefix rjp) service repair manual (rjp0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive on a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs installing 31 of the parts back into the final drive in reverse order and provides details on properly preloading the bearings and determining the correct shim thickness.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
This document provides instructions for removing and installing a crankshaft from a C7.1 engine. It describes removing components like the front housing, oil pump, seals and bearings. It then instructs how to attach lifting slings to the crankshaft and remove it from the engine block. Detailed steps are provided for cleaning, inspecting, and installing the crankshaft along with related components like thrust washers, bearing shells and caps. Tolerances and torques are specified to ensure proper installation.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 329 d l excavator (prefix ebm) service repair manual (ebm0000...fkjsekksmem
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and installing bolts to secure the jets in each cylinder.
- Procedures for removing pistons and connecting rods that include identifying parts, removing caps and bearings, and pushing components from the engine.
This document provides installation instructions for a rear power takeoff (RPTO) on a 323 excavator with a C7.1 engine. It involves cleaning components, pressing bearings into housings, aligning gears and idler hubs, lubricating and installing components, and tightening bolts to specified torques. The instructions also cover removing and installing the crankshaft pulley assembly and front seal.
Caterpillar cat 329 d l excavator (prefix wdk) service repair manual (wdk0000...ufjsjekfksemm
This document provides removal and assembly procedures for a travel motor on Caterpillar 329D and 329D L excavators. The removal procedure involves draining fluid, disconnecting hoses, removing bolts and pulling the travel motor out of the final drive. Disassembly of the travel motor requires removing the head, port plate, bearings, seals, springs, brake piston and various other internal components using specialized tools. The assembly procedure instructs to replace all seals and gaskets, clean all parts thoroughly, and install components in reverse order of removal while applying a film of oil. Proper cleanliness and torque specifications are emphasized throughout.
Caterpillar cat 319 d l excavator (prefix rjp) service repair manual (rjp0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive on a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs installing 31 of the parts back into the final drive in reverse order and provides details on properly preloading the bearings and determining the correct shim thickness.
Caterpillar cat 319 d l excavator (prefix wbj) service repair manual (wbj0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive component of a 319D LN excavator. It includes 33 steps for disassembly, removing components like the cover, carrier assembly, ring gears, and seals. The assembly section has 13 steps, including preloading the bearings to determine the correct shim thickness, installing seals and pins, and attaching the main housing to the motor housing. Precise cleaning and use of replacement parts is emphasized throughout.
This document provides instructions for removing and installing a crankshaft from a C7.1 engine. It describes removing components like the front housing, oil pump, seals and bearings. It then instructs how to attach lifting slings to the crankshaft and remove it from the engine block. Detailed steps are provided for cleaning, inspecting, and installing the crankshaft along with related components like thrust washers, bearing shells and caps. Tolerances and torques are specified to ensure proper installation.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 329 d l excavator (prefix ebm) service repair manual (ebm0000...fkjsekksmem
This document provides instructions for removing and installing various engine components on a Caterpillar 329D L and 329D LN excavator, including:
- Removing and installing the engine oil pan, which involves draining the oil, removing bolts and the pan, cleaning surfaces, applying sealant, and reinstalling with new bolts and gasket.
- Removing and installing piston cooling jets by removing and installing bolts to secure the jets in each cylinder.
- Procedures for removing pistons and connecting rods that include identifying parts, removing caps and bearings, and pushing components from the engine.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 d excavator (prefix jjm) service repair manual (jjm00001 ...jfdskekdmme
This document provides instructions for disassembling and assembling the travel motor on a 330D excavator. It lists the required tools and presents step-by-step procedures to remove and install various components of the travel motor like the head, brake piston, plates, seals, and bearings. Cleanliness is emphasized during disassembly and assembly to prevent contamination. All O-rings and gaskets must be replaced.
Caterpillar cat 318 f l excavator (prefix hcp) service repair manual (hcp0000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor of a 318F L Excavator. It lists the required tools and presents 31 steps for disassembly, including removing components like the springs, spools, caps, and head assembly. It then lists 29 steps for assembly, instructing technicians to install these components in reverse order. Safety warnings are provided throughout to avoid injury from spring forces. The document is intended to guide maintenance technicians through a complete travel motor overhaul.
Caterpillar cat 320 d rr excavator (prefix yds) service repair manual (yds000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor on a 320D RR excavator. It lists the required tools and parts. The disassembly procedure involves removing 25 components from the travel motor in a specific sequence. The assembly procedure instructs putting the travel motor back together in the reverse order and provides important notes to ensure proper installation.
Caterpillar cat 374 d l excavator (prefix pax) service repair manual (pax0000...fjkskedmme
The document provides instructions for disassembling and assembling components of a 374D L excavator travel motor and final drive system. It describes 17 steps to disassemble the final drive, including removing the final drive cover, ring gear, sun gears, carrier assemblies, planetary gears and shafts. Tools required include a transmission repair stand, link brackets, hydraulic wrench, hex bit socket and forcing bolts. Marks must be made to indicate original part locations for reassembly.
Caterpillar cat 336 e hvg excavator (prefix rbs) service repair manual (rbs00...f8isoeidkdk
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 349 d2 l excavator (prefix yae) service repair manual (yae000...cdsaas
The document provides instructions for assembling and installing a travel motor. It outlines 33 steps for assembling components like pistons, seals, plates, and bearings. Measurement checks are specified to ensure proper assembly. Tools required are listed. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 329 el excavator (prefix plw) service repair manual (plw00001...ufjjjskkemmd
This document provides instructions for removing and installing the crankshaft timing ring on a Caterpillar C7.1 engine. It describes removing the crankshaft, then removing the allen head screws and timing ring from the crankshaft. For installation, it instructs to clean the crankshaft flange, position the new timing ring on the crankshaft, and install new allen head screws to secure it. Proper cleaning and protection of parts from contamination is emphasized throughout.
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 323 excavator with a C7.1 engine.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The flywheel ring gear can then be removed by heating and punching.
3. Flywheel installation requires cleaning, installing the ring gear by heating and pressing it on, checking the rear seal for leaks, lifting the flywheel onto guide studs and torquing the bolts.
Caterpillar cat 160 h motor grader (prefix 2fm) service repair manual (2fm000...fiksfejjsekkmme
This document provides instructions for removing and installing the blade lift assembly on a 160H motor grader. It includes:
1) A list of required tools for removal and installation.
2) Step-by-step instructions for removing components like the blade lift arm, bar assembly, cylinder, and bearings.
3) Step-by-step instructions for installing replacement components in reverse order and adjusting shims to achieve proper clearance.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304 engine. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and applying lubricant before installing the camshaft back into the cylinder head.
2. Instructions detail cleaning the cylinder head before installing new camshaft bearings. The camshaft is then positioned and bolts are tightened to specifications.
3. Final steps include checking camshaft endplay and installing related components like the timing gear train before starting the engine.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v000...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 130G motor grader, including the cylinder head, spacer plate, and water directors. The removal process involves disconnecting related components like fuel lines, exhaust manifolds, and pushrods. Installation requires cleaning surfaces, applying new seals and gaskets, and torquing bolts to specified values. Precautions are outlined to prevent contamination and damage to parts.
Caterpillar cat 320 d lrr excavator (prefix zgb) service repair manual (zgb00...fjsekdmmeed
This document provides instructions for removing and installing the valve mechanism cover base on a 320D LRR excavator with a C6.4 engine. The removal procedure involves removing clips and disconnecting harnesses from the electronic unit injectors, then removing bolts to detach the cover base. The installation procedure specifies tightening bolts to the specified torques and reconnecting harnesses to reinstall the cover base. Precautions are provided to keep parts clean and prevent damage from contaminants.
Caterpillar cat 259 d compact track loader (prefix gtk) service repair manual...ujfjjskekfmmde
This document provides instructions for removing and installing pistons, connecting rods, and connecting rod bearings on a 259D Compact Track Loader. The removal procedure involves rotating the crankshaft, removing the connecting rod cap and bolts, pushing the piston and connecting rod out of the cylinder bore, and removing the piston and connecting rod. The installation procedure describes cleaning and lubricating components, inserting the piston and connecting rod into the cylinder bore, installing the connecting rod cap and bolts, and ensuring proper side play and no binding when rotating the crankshaft. Similar step-by-step processes are provided for disassembling, inspecting, and assembling the piston, connecting rod, and bearings.
Caterpillar cat 16 m motor grader (prefix b9h) service repair manual (b9h0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 16M motor grader in 50 steps. It lists all required tools and disassembles components such as sprockets, bearings, seals, gears, housings, and shafts. Safety notices are included to properly handle parts and avoid injury. Detailed illustrations accompany each step to ensure correct disassembly.
Kubota b20 tractor parts catalogue manualfhsejkdkmem
The document provides instructions and part numbers for a parts book. It includes 3 columns for each part: the reference number, part number, and description. There are over 200 parts listed across various systems of the machine like the engine, transmission, brakes, etc. Notes are provided to explain interchangeability of parts between different serial number ranges and country codes.
Kubota at70 s walk behind tiller parts catalogue manualfhsejkdkmem
The document provides instructions for parts books, including definitions of column headings in parts number pages such as Reference Number, Part Number, Description, Quantity, Serial Number range, Interchangeability, and Remarks. It notes country codes that may be included and their meanings. The remainder of the document is a sample parts book index and listing for an AT70S-AMERICA rotary tiller, with part numbers, descriptions, and other details for engine, transmission, rotary, and other systems components.
Hyundai r110 7 crawler excavator service repair manualfhsejkdkmem
This document provides instructions for removing and installing a hydraulic pump.
The key steps for removal are:
1) Draining the oil from the hydraulic tank and piping
2) Disconnecting all hoses and lines connected to the pump
3) Removing mounting bolts and pulling the pump assembly out of the housing
The key steps for installation are:
1) Cleaning and replacing any worn parts like filters or seals
2) Adding oil to the hydraulic tank
3) Bleeding air from the system by loosening vent plugs and running the engine
4) Checking for oil leaks after installation is complete.
The document also provides diagrams and part numbers for the pump components and instructions for
Hyundai r80 7 crawler excavator service repair manualfhsejkdkmem
This document provides instructions for disassembling and assembling the swing motor of an excavator. It details the removal and installation of the motor, as well as the disassembly and assembly procedures for the motor components. The motor contains over 40 parts including the housing, cylinder block, piston, valves, bearings, seals and more. Detailed steps are provided for removing each part, with notes on proper handling and marking of parts for reassembly. Safety precautions are highlighted, such as relieving hydraulic pressure before disconnection and not reusing seals.
Hyundai r75 7 mini excavator service repair manualfhsejkdkmem
This service manual provides maintenance and repair instructions for the excavator. It includes sections on safety precautions, equipment outlines, inspection and repair procedures, and troubleshooting. The goal is to help technicians efficiently and effectively service the excavator by providing accurate product details and proper repair techniques. Key systems covered include the engine, hydraulics, undercarriage, electrical components, and more. Maintaining the equipment according to the schedules outlined in the manual can help ensure long life.
Hyundai r55 7 a crawler excavator service repair manualfhsejkdkmem
This service manual contains 8 sections that provide technical information for operations performed in a service workshop. Section 1 provides general safety hints and specifications. Section 2 explains the structure and function of each major component. Section 3 describes the hydraulic system, including circuits and operation. Section 4 covers the electrical system, components, and circuits. Section 5 is about troubleshooting hydraulic, mechanical, and electrical systems. Section 6 includes maintenance standards and procedures. Section 7 gives instructions for disassembly and assembly of components. Section 8 provides recommended component mounting torques.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 d excavator (prefix jjm) service repair manual (jjm00001 ...jfdskekdmme
This document provides instructions for disassembling and assembling the travel motor on a 330D excavator. It lists the required tools and presents step-by-step procedures to remove and install various components of the travel motor like the head, brake piston, plates, seals, and bearings. Cleanliness is emphasized during disassembly and assembly to prevent contamination. All O-rings and gaskets must be replaced.
Caterpillar cat 318 f l excavator (prefix hcp) service repair manual (hcp0000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor of a 318F L Excavator. It lists the required tools and presents 31 steps for disassembly, including removing components like the springs, spools, caps, and head assembly. It then lists 29 steps for assembly, instructing technicians to install these components in reverse order. Safety warnings are provided throughout to avoid injury from spring forces. The document is intended to guide maintenance technicians through a complete travel motor overhaul.
Caterpillar cat 320 d rr excavator (prefix yds) service repair manual (yds000...fjkskedmme
This document provides instructions for disassembling and assembling the travel motor on a 320D RR excavator. It lists the required tools and parts. The disassembly procedure involves removing 25 components from the travel motor in a specific sequence. The assembly procedure instructs putting the travel motor back together in the reverse order and provides important notes to ensure proper installation.
Caterpillar cat 374 d l excavator (prefix pax) service repair manual (pax0000...fjkskedmme
The document provides instructions for disassembling and assembling components of a 374D L excavator travel motor and final drive system. It describes 17 steps to disassemble the final drive, including removing the final drive cover, ring gear, sun gears, carrier assemblies, planetary gears and shafts. Tools required include a transmission repair stand, link brackets, hydraulic wrench, hex bit socket and forcing bolts. Marks must be made to indicate original part locations for reassembly.
Caterpillar cat 336 e hvg excavator (prefix rbs) service repair manual (rbs00...f8isoeidkdk
The document provides instructions for installing a rear power take-off (RPTO) on a C9.3 engine. The procedure involves installing various components like a bearing, thrust washer, dowels, adapter assembly, idler gear and shaft. Tools like guide studs and driver groups are required. Torque specifications and the correct sequence are important to properly install the RPTO.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 349 d2 l excavator (prefix yae) service repair manual (yae000...cdsaas
The document provides instructions for assembling and installing a travel motor. It outlines 33 steps for assembling components like pistons, seals, plates, and bearings. Measurement checks are specified to ensure proper assembly. Tools required are listed. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 329 el excavator (prefix plw) service repair manual (plw00001...ufjjjskkemmd
This document provides instructions for removing and installing the crankshaft timing ring on a Caterpillar C7.1 engine. It describes removing the crankshaft, then removing the allen head screws and timing ring from the crankshaft. For installation, it instructs to clean the crankshaft flange, position the new timing ring on the crankshaft, and install new allen head screws to secure it. Proper cleaning and protection of parts from contamination is emphasized throughout.
1. The document provides instructions for removing and installing the flywheel and crankshaft rear seal on a Caterpillar 323 excavator with a C7.1 engine.
2. To remove the flywheel, bolts must first be removed and guide studs installed before lifting the flywheel off using a lifting device. The flywheel ring gear can then be removed by heating and punching.
3. Flywheel installation requires cleaning, installing the ring gear by heating and pressing it on, checking the rear seal for leaks, lifting the flywheel onto guide studs and torquing the bolts.
Caterpillar cat 160 h motor grader (prefix 2fm) service repair manual (2fm000...fiksfejjsekkmme
This document provides instructions for removing and installing the blade lift assembly on a 160H motor grader. It includes:
1) A list of required tools for removal and installation.
2) Step-by-step instructions for removing components like the blade lift arm, bar assembly, cylinder, and bearings.
3) Step-by-step instructions for installing replacement components in reverse order and adjusting shims to achieve proper clearance.
Caterpillar cat 130 g motor grader (prefix 12w) service repair manual (12w010...fjsekdmmeed
1. The document provides instructions for removing and installing a camshaft on a Caterpillar 3304 engine. Key steps include using a lifting device to remove the camshaft, checking camshaft journals for wear, and applying lubricant before installing the camshaft back into the cylinder head.
2. Instructions detail cleaning the cylinder head before installing new camshaft bearings. The camshaft is then positioned and bolts are tightened to specifications.
3. Final steps include checking camshaft endplay and installing related components like the timing gear train before starting the engine.
Caterpillar cat 130 g motor grader (prefix 74v) service repair manual (74v000...fjsekdmmeed
This document provides instructions for removing and installing various engine components on a Caterpillar 130G motor grader, including the cylinder head, spacer plate, and water directors. The removal process involves disconnecting related components like fuel lines, exhaust manifolds, and pushrods. Installation requires cleaning surfaces, applying new seals and gaskets, and torquing bolts to specified values. Precautions are outlined to prevent contamination and damage to parts.
Caterpillar cat 320 d lrr excavator (prefix zgb) service repair manual (zgb00...fjsekdmmeed
This document provides instructions for removing and installing the valve mechanism cover base on a 320D LRR excavator with a C6.4 engine. The removal procedure involves removing clips and disconnecting harnesses from the electronic unit injectors, then removing bolts to detach the cover base. The installation procedure specifies tightening bolts to the specified torques and reconnecting harnesses to reinstall the cover base. Precautions are provided to keep parts clean and prevent damage from contaminants.
Caterpillar cat 259 d compact track loader (prefix gtk) service repair manual...ujfjjskekfmmde
This document provides instructions for removing and installing pistons, connecting rods, and connecting rod bearings on a 259D Compact Track Loader. The removal procedure involves rotating the crankshaft, removing the connecting rod cap and bolts, pushing the piston and connecting rod out of the cylinder bore, and removing the piston and connecting rod. The installation procedure describes cleaning and lubricating components, inserting the piston and connecting rod into the cylinder bore, installing the connecting rod cap and bolts, and ensuring proper side play and no binding when rotating the crankshaft. Similar step-by-step processes are provided for disassembling, inspecting, and assembling the piston, connecting rod, and bearings.
Caterpillar cat 16 m motor grader (prefix b9h) service repair manual (b9h0000...fjsekdmmeed
This document provides disassembly instructions for the rear axle, differential, and final drive of a 16M motor grader in 50 steps. It lists all required tools and disassembles components such as sprockets, bearings, seals, gears, housings, and shafts. Safety notices are included to properly handle parts and avoid injury. Detailed illustrations accompany each step to ensure correct disassembly.
Kubota b20 tractor parts catalogue manualfhsejkdkmem
The document provides instructions and part numbers for a parts book. It includes 3 columns for each part: the reference number, part number, and description. There are over 200 parts listed across various systems of the machine like the engine, transmission, brakes, etc. Notes are provided to explain interchangeability of parts between different serial number ranges and country codes.
Kubota at70 s walk behind tiller parts catalogue manualfhsejkdkmem
The document provides instructions for parts books, including definitions of column headings in parts number pages such as Reference Number, Part Number, Description, Quantity, Serial Number range, Interchangeability, and Remarks. It notes country codes that may be included and their meanings. The remainder of the document is a sample parts book index and listing for an AT70S-AMERICA rotary tiller, with part numbers, descriptions, and other details for engine, transmission, rotary, and other systems components.
Hyundai r110 7 crawler excavator service repair manualfhsejkdkmem
This document provides instructions for removing and installing a hydraulic pump.
The key steps for removal are:
1) Draining the oil from the hydraulic tank and piping
2) Disconnecting all hoses and lines connected to the pump
3) Removing mounting bolts and pulling the pump assembly out of the housing
The key steps for installation are:
1) Cleaning and replacing any worn parts like filters or seals
2) Adding oil to the hydraulic tank
3) Bleeding air from the system by loosening vent plugs and running the engine
4) Checking for oil leaks after installation is complete.
The document also provides diagrams and part numbers for the pump components and instructions for
Hyundai r80 7 crawler excavator service repair manualfhsejkdkmem
This document provides instructions for disassembling and assembling the swing motor of an excavator. It details the removal and installation of the motor, as well as the disassembly and assembly procedures for the motor components. The motor contains over 40 parts including the housing, cylinder block, piston, valves, bearings, seals and more. Detailed steps are provided for removing each part, with notes on proper handling and marking of parts for reassembly. Safety precautions are highlighted, such as relieving hydraulic pressure before disconnection and not reusing seals.
Hyundai r75 7 mini excavator service repair manualfhsejkdkmem
This service manual provides maintenance and repair instructions for the excavator. It includes sections on safety precautions, equipment outlines, inspection and repair procedures, and troubleshooting. The goal is to help technicians efficiently and effectively service the excavator by providing accurate product details and proper repair techniques. Key systems covered include the engine, hydraulics, undercarriage, electrical components, and more. Maintaining the equipment according to the schedules outlined in the manual can help ensure long life.
Hyundai r55 7 a crawler excavator service repair manualfhsejkdkmem
This service manual contains 8 sections that provide technical information for operations performed in a service workshop. Section 1 provides general safety hints and specifications. Section 2 explains the structure and function of each major component. Section 3 describes the hydraulic system, including circuits and operation. Section 4 covers the electrical system, components, and circuits. Section 5 is about troubleshooting hydraulic, mechanical, and electrical systems. Section 6 includes maintenance standards and procedures. Section 7 gives instructions for disassembly and assembly of components. Section 8 provides recommended component mounting torques.
Hyundai r35 z 7a mini excavator service repair manualfhsejkdkmem
(1) The document provides instructions for removing and installing a hydraulic pump. It describes loosening bolts and disconnecting hoses to remove the pump and drain the oil tank.
(2) It also describes installing the pump by reversing the removal steps and includes cleaning parts and bleeding air from the system.
(3) The document provides detailed parts lists and diagrams to aid in disassembling and assembling the various components of the pump such as the shaft assembly, rotary group, and gear pump. It emphasizes cleaning parts and proper installation of seals and gaskets.
Hyundai r35 7 mini excavator service repair manualfhsejkdkmem
This service manual provides maintenance and repair instructions for the machine. It includes sections on safety precautions, machine outlines and specifications, maintenance schedules, troubleshooting, and repairs for individual machine systems. Proper maintenance following the schedules and procedures in the manual is important to ensure the long life of the machine and prevent failures.
Hyundai r28 7 mini excavator service repair manualfhsejkdkmem
This service manual provides instructions for maintaining a hydraulic excavator to ensure its long life. It covers inspection and repair procedures for the engine, pumps, cylinders, undercarriage, electrical components, and other parts. Proper maintenance following the schedules and procedures outlined is important for preventing failures and problems. The manual also provides part names and specifications to aid in repairs. Precautions are outlined to safely and efficiently perform disassembly, cleaning, inspection, assembly and adjustment of components as needed.
Daewoo doosan solar s220 lc v excavator operator and maintenance manualfhsejkdkmem
This document provides safety information for operating and maintaining a Daewoo excavator. It includes sections on general safety essentials, location of safety labels, lifting precautions, worksite precautions, operation, equipment, maintenance, transportation, and specifications. Operators must follow all safety guidelines and instructions from the manual to prevent injuries or damage from occurring.
Daewoo doosan solar 470 lc v excavator operator and maintenance manualfhsejkdkmem
1. The document provides safety information and instructions for operating a Daewoo excavator.
2. It identifies the location of various safety labels on the excavator and explains their meanings.
3. Operators and maintenance personnel are instructed to read the manual thoroughly before operating or servicing the excavator to avoid accidents.
Daewoo doosan solar 420 lc v excavator operator and maintenance manualfhsejkdkmem
The document provides safety information and instructions for operating a Daewoo excavator, including:
1. The location and descriptions of safety labels on the excavator.
2. A summary of safety precautions for lifting loads in digging mode.
3. General hazard information, safety precautions for starting the engine, machine operation, maintenance, batteries, towing, shipping, and lift capacity tables.
Daewoo doosan solar 400 lc v excavator operator and maintenance manualfhsejkdkmem
The document provides safety information and instructions for operating a Daewoo excavator, including:
1. Warnings to read all safety information and understand signal words before operating.
2. Locations of safety labels on the excavator and their meanings.
3. Precautions for lifting loads, including checking regulations, using approved lifting configurations, and having tag lines for secured loads.
Daewoo doosan solar 340 lc v excavator operator and maintenance manualfhsejkdkmem
The document provides safety information and instructions for operating a Daewoo excavator, including:
1. The location and descriptions of safety labels on the excavator.
2. A summary of safety precautions for lifting loads in digging mode.
3. General hazard information and safety precautions for before starting the engine, machine operation, maintenance, batteries, towing, shipping, and transportation.
Daewoo doosan solar 290 lc v excavator operator and maintenance manualfhsejkdkmem
This document provides safety information and operating instructions for a Daewoo excavator. It includes sections on safety essentials, locations of safety labels on the machine, lifting precautions, worksite precautions, operation, equipment, maintenance, transportation, and specifications. The document emphasizes following all safety guidelines and instructions to avoid injury or damage from machine hazards. It also warns operators to avoid contact with electric lines and other overhead hazards.
Crown ws2000 series forklift parts catalogue manualfhsejkdkmem
This document is a parts manual for the WE/WS2000 series. It contains 10 sections that list parts for different systems of the trucks, including covers, frames, hydraulic and electrical components, brakes, and more. Each section includes an index listing part numbers, part names, and quantities of parts required. Product information like model numbers and serial numbers are needed to order replacement parts.
Crown wp2300 s series pallet truck parts catalogue manualfhsejkdkmem
This document is a parts manual for a WP2300S series truck. It contains 10 sections that cover different parts of the truck such as covers, hydraulic parts, electrical parts, brakes, mast/lift structure, cylinders, and miscellaneous items. The sections include exploded diagrams of the assemblies and lists of the individual parts with part numbers. Fixed platforms were added to pages 82 and 83.
Crown wp2300 series pallet truck parts catalogue manualfhsejkdkmem
This parts manual provides exploded diagrams and lists of parts for a WP2300 series walk-behind pallet truck. Section 2 covers the hydraulic system, including the tube and hose layout, pump, motor and related parts. Diagrams show the configuration and connections of hydraulic hoses and tubes between the pump, lift cylinder, control valves and other components. Part numbers and descriptions are provided for each item.
Crown wp2000 s series pallet truck parts catalogue manualfhsejkdkmem
This parts manual provides exploded diagrams and part lists for replacing components on a WP2000S series forklift. The document includes 10 sections covering the truck's covers, hydraulic system, drive unit, electrical systems, brake system, mast/lift structure, cylinders, cabin/platform, and miscellaneous parts. Ordering replacement parts requires specifying the forklift model, serial number, and part number from the manual. Modifications to the forklift must be approved in writing by the manufacturer to ensure safety.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323 EXCAVATOR YBL
Configuration: 323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05292388
Rear Power Take-Off (RPTO) - Install
SMCS - 1165-012-RE
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that all components of the rear power take-off (RPTO) are clean and free from wear
and damage.
1/9
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g02069024
2. If necessary, follow Steps 2.a through Steps 2.c in order to install the sleeve bearing from
the flywheel housing.
a. Accurately align oil Holes (X) in sleeve bearing (20) with the oil holes in flywheel
housing (9).
b. Use Tooling (A) in order to install sleeve bearing (20) into flywheel housing (9).
Note: Ensure that the oil holes are correctly aligned. If the oil holes are not correctly
aligned, the sleeve bearing should be removed.
c. Repeat Step 2.a through Steps 2.c in order to install sleeve bearing (21) to flywheel
housing (9).
3/9
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 4 g02069021
3. If necessary, follow Steps 3.a through Steps 3.d in order to install the sleeve bearing to the
gears.
a. Place gear (17) onto suitable support.
b. Accurately align Grooves (Z) in sleeve bearing (20) with Grooves (Y) in gear (17).
c. Use Tooling (A) and a suitable press in order to install sleeve bearing (19) into gear
(17).
d. Repeat Steps 3.a through Step 3.c in order to install the sleeve bearing to gear (18).
4. Lubricate idler hub (15) and gear (17) with clean oil. Install idler hub (15) to gear (17).
Note: Ensure that the gear and the idler hub are correctly oriented.
5. Install gear (17) and idler hub (15) assembly to flywheel housing (9).
Note: Ensure that the oil hole in the idler hub is correctly positioned.
6. Install bolts (13) to idler hub (15) and hand tighten bolts.
Note: Ensure that the idler hub is correctly aligned to the flywheel housing.
7. Repeat Steps 4 through Step 6 in order to install gear (18), idler hub (16) and bolts (14) to
flywheel housing (9).
5/9
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 8. Tighten bolts (13) and bolts (14) to a torque of 100 N·m (74 lb ft).
9. Ensure that there is tactile backlash between gear (17) and gear (18). Ensure that there is
end play between the idler hubs and the gears.
Illustration 5 g02069020
10. install gear assembly (11) and gear assembly (12) to flywheel housing (9).
6/9
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 7 g02070473
11. If necessary, follow Steps 11.a through Steps 11.c in order to install the sleeve bearing to
the adapter.
a. Place adapter (2) onto suitable support.
b. Use Tooling (A) and a suitable press in order to install sleeve bearing (10) into
adapter (2).
c. Repeat Steps 11.a through Step 11.b in order to install the sleeve bearing into adapter
(5).
12. Install a new O-ring seal (3) (not shown) to adapter (2).
13. Install adapter (2) to flywheel housing (9).
Note: Ensure correct orientation of the adapter.
14. Install bolts (1) and tighten the bolts to a torque of 55 N·m (41 lb ft).
15. Install a new O-ring seal (6) (not shown) to adapter (5).
16. Install adapter (5) to flywheel housing (9).
Note: Ensure correct orientation of the adapter.
17. Install bolts (4) and tighten the bolts to a torque of 55 N·m (41 lb ft).
8/9
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 18. Ensure that there is tactile backlash between the gears. Ensure that there is end play between
the gears and the flywheel housing and the adapters.
19. Install gear (7) to crankshaft (8).
20. If necessary, install the OEM equipment to the rear power take-off (RPTO).
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install" for the correct
procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 25 01:14:00 UTC+0800 2020
9/9
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323 EXCAVATOR YBL
Configuration: 323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05909481
Vibration Damper and Pulley - Remove
SMCS - 1205-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
Start By:
A. Remove the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt - Remove
and Install" for the correct procedure.
Note: The weight of the assembly of the crankshaft pulley, the vibration damper, and the
crankshaft adapter is approximately 22 kg (48 lb).
1/3
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g02368017
1. Use a suitable tool in order to prevent the crankshaft from rotating. Use Tooling (B) to
remove one Torx screws (1) from crankshaft pulley assembly (2) .
2. Install Tooling (A) into crankshaft pulley assembly (2) .
3. Remove remaining Torx screws (1) from crankshaft pulley assembly (2) .
4. Remove crankshaft pulley assembly (2) .
5. Remove Tooling (A) .
2/3
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 2 g02368018
6. If necessary, follow Step 6.a through Step 6.b in order to remove friction shim (3) from the
crankshaft.
a. Remove the front seal from the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
b. Remove friction shim (3) .
7. If necessary, follow Step 7.a through Step 7.c in order to disassemble vibration damper,
crankshaft pulley from crankshaft adapter.
a. Place the crankshaft pulley assembly onto a suitable support.
b. Remove bolts (7) from crankshaft pulley assembly (2) .
c. Remove vibration damper (6) and crankshaft pulley (5) from adapter (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 25 01:15:00 UTC+0800 2020
3/3
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323 EXCAVATOR YBL
Configuration: 323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05909490
Vibration Damper and Pulley - Install
SMCS - 1205-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Stud
M14 x 1.5 by 100 mm
1
B 227-4393 E18 Torx Socket 1
C 8T-3052 Degree Wheel 1
D -
Guide Studs
M12 x 1.75 by 50 mm
2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 1 g02368018
1. Ensure that the crankshaft adapter and the front of the crankshaft are clean and free from
damage.
2. Inspect vibration damper (6) for damage. If necessary, replace the vibration damper.
3. If necessary, follow Step 3.a through Step 3.e in order to install vibration damper,
crankshaft pulley to crankshaft adapter.
a. Place crankshaft adapter (4) onto a suitable support.
b. Install Tooling (D) crankshaft adapter (4) .
c. Install crankshaft pulley (5) and vibration damper (6) over Tooling (D) .
d. Install bolts (7) to the crankshaft pulley assembly.
Note: Evenly space bolts (7) around the crankshaft pulley assembly.
e. Tighten bolts (7) to a torque of 115 N·m (85 lb ft).
4. If necessary, install friction shim (3) . Follow Step 4.a through Step 4.b in order to install
friction shim (3) .
a. Install friction shim (3) .
2/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. b. Install a new front seal to the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
5. Install Tooling (A) to the crankshaft.
Illustration 2 g02368017
6. Install crankshaft pulley assembly (2) onto the crankshaft.
7. Install one Torx screws (1) to crankshaft pulley assembly (2) hand tighten.
8. Remove Tooling (A) .
9. Install remaining Torx screws (1) to crankshaft pulley assembly (2) .
10. Use a suitable tool in order to prevent the crankshaft from rotating. Tighten Torx screws (1)
to a torque of 40 N·m (29 lb ft).
11. Use Tooling (B) and Tooling (C) to turn Torx screws (1) through an additional 120 degrees.
End By: Install the alternator belt. Refer to Disassembly and Assembly, "Alternator Belt -
Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Fri Sep 25 01:16:00 UTC+0800 2020
3/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323 EXCAVATOR YBL
Configuration: 323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05292118
Crankshaft Front Seal - Remove and Install - Crankshaft
Front Seal for Heavy Duty Front Cover
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 278-2636 Front Oil Seal Removal Tool 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g02048634
1. Position Tooling (A) on the nose of the crankshaft. Screw Tooling (A) into crankshaft front
seal (2).
Note: Do not damage the edge of the front cover for the crankshaft front seal.
2. Screw the bolt into Tooling (A) in order to remove crankshaft front seal (2) from front cover
(1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B
9U-6206 Stud Front Seal Installer 1
9U-6207 Plate 1
9U-6209 Sleeve Plate 1
9U-6211 Seal Installer Tool 1
366-5984 Installer Assembly
2/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the bore for the crankshaft front oil seal in the front cover is clean and free from
damage.
Illustration 2 g03413520
2. Assemble Tooling (B).
3. Correctly position a new crankshaft front seal (2) to front cover (1).
Note: If the crankshaft front seal is supplied with a sleeve, remove the sleeve from the
crankshaft front seal before installation.
4. Use Tooling (B) to install crankshaft front seal (2) to front cover (1). Ensure that the front
face of the crankshaft front seal is installed to a depth of 6.5 ± 0.2 mm (0.256 ± 0.008 inch).
5. Remove Tooling (B) from the crankshaft.
End By:
3/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 25 01:16:59 UTC+0800 2020
4/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323 EXCAVATOR YBL
Configuration: 323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05292119
Crankshaft Front Seal - Remove and Install
SMCS - 1160-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 278-2636 Front Oil Seal Removal Tool 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g03429500
1. Position Tooling (A) on the nose of the crankshaft. Screw Tooling (A) into crankshaft front
seal (1).
Note: Do not damage the edge of the housing for the crankshaft front seal.
2. Screw bolt (2) into Tooling (A) in order to remove crankshaft front seal (1).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B
9U-6206 Stud Front Seal Installer 1
9U-6207 Plate 1
9U-6209 Sleeve Plate 1
9U-6211 Seal Installer Tool 1
366-5984 Installer Assembly
2/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that the bore for the crankshaft front seal in the front housing is clean and free from
damage.
Illustration 2 g03429501
2. Assemble Tooling (B).
3. Align new crankshaft front seal (1) to the front housing.
Note: If the crankshaft front seal is supplied with a sleeve, remove the sleeve from the
crankshaft front seal before installation.
4. Use Tooling (B) to install crankshaft front seal (1). Ensure that the front face of the seal is
installed to a depth of 6.5 ± 0.2 mm (0.256 ± 0.008 inch) into the front housing.
5. Remove Tooling (B) from the crankshaft.
End By:
3/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 25 01:17:59 UTC+0800 2020
4/4
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323 EXCAVATOR YBL
Configuration: 323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
C7.1 Engines
Media Number -UENR0633-19 Publication Date -01/07/2015 Date Updated -29/10/2018
i05292301
Front Cover - Remove and Install - Heavy Duty Front Cover
SMCS - 1166-010
Removal Procedure
Start By:
a. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump- Remove" for
the correct procedure.
b. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Vibration Damper and
Pulley - Remove" for the correct procedure.
c. If the engine is equipped with a fan, remove the fan. Refer to Disassembly and Assembly,
"Fan - Remove and Install" for the correct procedure.
d. Remove the crankshaft front seal from the front cover. Refer to Disassembly and Assembly,
"Crankshaft Front Seal - Remove and Install" for the correct procedure.
1/5
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g03410400
1. Remove bolts (3), bolts (4), and bolts (5). Identify the positions of bolts of different length.
2. Remove front cover (1) from the front housing.
3. Remove gasket (2).
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A -
Guide Studs
M8 by 70 mm
2
B 364-7210 Front Cover Alignment Tool 1
2/5
323 Excavator YBL00001-UP (MACHINE) POWERED BY C7.1 Engine(M0085279 ...
2020/9/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...