This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. The assembly process describes 24 steps and provides illustrations to reinstall all components in the reverse order of disassembly. Precautions are noted to ensure proper alignment of components and prevent damage during assembly.
Caterpillar cat 330 b l excavator (prefix 5lr) service repair manual (5lr0000...fjskefkemms
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the components and steps in the process.
Caterpillar cat 323 d s excavator (prefix rac) service repair manual (rac0000...fusjejkdkmse
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes:
1. Removing the valves, electronic unit injectors, and turning the cylinder head over to access the valve guides.
2. Using specialty tools to remove the old valve guides and install new guides.
3. Notching and extracting the valve seat inserts using specialty tools before cleaning and installing new inserts.
4. Installing the valve seat inserts, valves, and electronic unit injectors to complete the job.
Caterpillar cat 323 f l excavator (prefix yej) service repair manual (yej0000...fusjejkdkmse
This document provides instructions for removing and installing various components of the front end of a Caterpillar C7.1 diesel engine, including the crankshaft front seal, front cover, and gear group. The procedures describe using various specialized tools to correctly position and time components. Precautions are outlined for cleaning parts and installing new seals and gaskets.
The document provides instructions for removing and installing a cylinder head on a 3054C engine. Key steps include:
1. Draining fluids, removing related components like the exhaust manifold and fuel injectors before removing the cylinder head.
2. Gradually loosening and removing cylinder head bolts in reverse order to prevent distortion, then lifting off the head using a lifting device.
3. Cleaning the cylinder block and head mating surfaces, installing a new gasket and dowel pins before positioning the head back on using guide bolts for alignment.
4. Reinstalling the bolts and tightening them in stages to the specified torque in numerical order.
Hyundai 80 d 7e forklift truck service repair manualfjjsekmmm
The document provides instructions for disassembling and assembling a steering unit. It describes the individual parts of the steering unit and lists the necessary tools. The steps for disassembly include removing the end cover, gearwheel set, cardan shaft, distributor plate, check valve parts, thrust bearing and races from the sleeve and spool. Assembly involves reversing these steps, making sure to properly position springs, seals, and other small parts. Torque specifications are provided for mounting bolts.
Hyundai 50 df 7 forklift truck service repair manualfusjejkdkmse
This document provides an overview and table of contents for a service manual. It outlines the general safety information covered in Section 1 and describes the procedures for removal, installation, and repair covered in Sections 2 through 8. These sections address the power train system, brake system, steering system, hydraulic system, electrical system, and mast. The document also provides directions for how to read and organize the service manual.
Hyundai hbf18 t 5 forklift truck service repair manualfjjsekmmm
This document provides instructions for disassembling and assembling the steering unit of a machine. It includes the following sections:
1. Tools and torque specifications needed for the job.
2. Instructions for disassembling components like the end cover, gearwheel set, cardan shaft, distributor plate, seals and springs.
3. Instructions for assembling components like the spool, sleeve, seals, springs and end cover. Precise steps are provided to ensure correct assembly.
Kubota v3300 e2 b diesel engine service repair manualfusjejkdkmse
This workshop manual provides information on servicing the V3300-E2B and V3300-T-E2B diesel engines. It is divided into three parts: General, Mechanism, and Servicing. The General section includes engine identification, general precautions, maintenance checklists, and check and maintenance procedures. The Mechanism section describes the engine construction and functions. The Servicing section covers troubleshooting, specifications, torque values, adjustments, disassembly/assembly procedures, and servicing. The manual is intended to inform service personnel about servicing and maintaining these engines.
Caterpillar cat 330 b l excavator (prefix 5lr) service repair manual (5lr0000...fjskefkemms
This document provides instructions for removing and installing various engine components on Caterpillar 330B L and 330B LN excavator models, including the cylinder head, spacer plate, water directors, lifter group, and camshaft. The procedures describe cleaning parts, applying lubricants, and tightening bolts to specified torques. Detailed illustrations show the components and steps in the process.
Caterpillar cat 323 d s excavator (prefix rac) service repair manual (rac0000...fusjejkdkmse
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes:
1. Removing the valves, electronic unit injectors, and turning the cylinder head over to access the valve guides.
2. Using specialty tools to remove the old valve guides and install new guides.
3. Notching and extracting the valve seat inserts using specialty tools before cleaning and installing new inserts.
4. Installing the valve seat inserts, valves, and electronic unit injectors to complete the job.
Caterpillar cat 323 f l excavator (prefix yej) service repair manual (yej0000...fusjejkdkmse
This document provides instructions for removing and installing various components of the front end of a Caterpillar C7.1 diesel engine, including the crankshaft front seal, front cover, and gear group. The procedures describe using various specialized tools to correctly position and time components. Precautions are outlined for cleaning parts and installing new seals and gaskets.
The document provides instructions for removing and installing a cylinder head on a 3054C engine. Key steps include:
1. Draining fluids, removing related components like the exhaust manifold and fuel injectors before removing the cylinder head.
2. Gradually loosening and removing cylinder head bolts in reverse order to prevent distortion, then lifting off the head using a lifting device.
3. Cleaning the cylinder block and head mating surfaces, installing a new gasket and dowel pins before positioning the head back on using guide bolts for alignment.
4. Reinstalling the bolts and tightening them in stages to the specified torque in numerical order.
Hyundai 80 d 7e forklift truck service repair manualfjjsekmmm
The document provides instructions for disassembling and assembling a steering unit. It describes the individual parts of the steering unit and lists the necessary tools. The steps for disassembly include removing the end cover, gearwheel set, cardan shaft, distributor plate, check valve parts, thrust bearing and races from the sleeve and spool. Assembly involves reversing these steps, making sure to properly position springs, seals, and other small parts. Torque specifications are provided for mounting bolts.
Hyundai 50 df 7 forklift truck service repair manualfusjejkdkmse
This document provides an overview and table of contents for a service manual. It outlines the general safety information covered in Section 1 and describes the procedures for removal, installation, and repair covered in Sections 2 through 8. These sections address the power train system, brake system, steering system, hydraulic system, electrical system, and mast. The document also provides directions for how to read and organize the service manual.
Hyundai hbf18 t 5 forklift truck service repair manualfjjsekmmm
This document provides instructions for disassembling and assembling the steering unit of a machine. It includes the following sections:
1. Tools and torque specifications needed for the job.
2. Instructions for disassembling components like the end cover, gearwheel set, cardan shaft, distributor plate, seals and springs.
3. Instructions for assembling components like the spool, sleeve, seals, springs and end cover. Precise steps are provided to ensure correct assembly.
Kubota v3300 e2 b diesel engine service repair manualfusjejkdkmse
This workshop manual provides information on servicing the V3300-E2B and V3300-T-E2B diesel engines. It is divided into three parts: General, Mechanism, and Servicing. The General section includes engine identification, general precautions, maintenance checklists, and check and maintenance procedures. The Mechanism section describes the engine construction and functions. The Servicing section covers troubleshooting, specifications, torque values, adjustments, disassembly/assembly procedures, and servicing. The manual is intended to inform service personnel about servicing and maintaining these engines.
Hyundai 20253032 bc 7 forklift truck service repair manualfjjsekmmm
This document provides instructions for disassembling and assembling the steering unit of a machine. It describes removing components like the end cover, gearwheel set, cardan shaft, distributor plate, check valve parts, thrust bearing and springs. It then explains how to reassemble these parts, including pressing in seals and springs correctly. Tools needed are also listed along with tightening torques for mounting bolts.
Hyundai 50 ds 7e forklift truck service repair manualfusjejkdkmse
This document provides an overview and outline of the sections contained in a service manual for a machine. It begins with general safety information and specifications in Section 1. Section 2 covers removal and installation procedures. Sections 3 through 8 each describe a different mechanical system of the machine, including the power train, brakes, steering, hydraulics, electrical, and mast. Each section is divided into groups covering the structure and operation, maintenance, troubleshooting, disassembly and assembly of that system. Conversion tables are also provided as a reference.
Hyundai brj series forklift truck service repair manualfjjsekmmm
This document provides an overview and outline of the service manual for a machine. It includes 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. The foreword explains the structure and purpose of the manual. It also provides guidance on how to read page numbers and file pages in the correct order. The conversion table section includes tables to enable simple conversions between units of measurement like millimeters to inches, kilograms to pounds, liters to gallons, etc.
Hyundai 250 d 7e forklift truck service repair manualfjjsekmmm
This document contains an overview and table of contents for a service manual for an unspecified machine. It outlines 8 sections that will be covered in the manual, including general information, removal/installation procedures, descriptions of the power train, brake, steering, hydraulic, and electrical systems, and the mast. The foreword provides information on how the manual is organized and formatted. It is intended to help technicians properly service the machine by providing accurate technical information and instructions.
Hyundai 30 df forklift truck service repair manualfjjsekmsmmes
The document describes the power train system of a vehicle. It includes the engine, transmission, drive shaft, drive axle, and brakes. The transmission uses a torque converter and power shift transmission to transfer power from the engine to the drive axle. It includes a control valve that regulates oil pressure and directs it to engage either the forward or reverse clutch, allowing the vehicle to shift gears automatically based on engine speed. The transmission case houses the transmission components and control valve, and includes an oil filter and parking brake.
Kubota v3600 t-e3 b diesel engine service repair manualfusjejkdkmse
This document provides service technicians with information on servicing and maintaining various Kubota diesel engine models. It is divided into three parts covering general information, engine mechanisms, and servicing procedures.
The general section includes instructions on identifying engine models, general safety precautions, maintenance checklists, and maintenance schedules. Technicians are advised to check specific components and systems daily, every 50 hours, 250 hours, 500 hours, and longer intervals. The document also lists special tools needed for servicing tasks.
This document is a service manual for MerCruiser GM 4 cylinder 181 cid (3.0L) marine engines. It provides information on engine components, maintenance procedures, troubleshooting, removal and installation of engine systems, and specifications. Safety notices are included throughout to warn technicians of hazards.
Caterpillar cat 930 r wheel loader (prefix 57z) service repair manual (57z040...fujskekfmsme
This document provides instructions for installing the fuel injection pump housing and governor on a Caterpillar 930T wheel loader. It describes:
1) Using an engine turning tool to find the top center position of the No. 1 piston by turning the flywheel and installing a bolt in a hole in the flywheel.
2) Installing fuel pump timing pins and checking that the fuel injection pump gear teeth are aligned with the timing marks on the housing.
3) Installing the fuel injection pump housing and governor, and checking that the governor shaft turns freely once assembled.
Hyundai hdf15 3 forklift truck service repair manualfjjsekmmm
This document outlines the contents and structure of a service manual for a machine. It includes 8 sections that cover general information, removal and installation of components, power train, brake, steering, hydraulic, electrical, and mast systems. Each section contains groups that provide details on the structure, operation, troubleshooting, testing, and disassembly/assembly of the various systems. Specifications, conversions charts for measurements, and a temperature conversion table are also included at the beginning.
John deere f911 front mower service repair manualfjjskdmnenemm
This technical manual provides service information for John Deere F911, F915, F925, F932, and F935 front mowers. The manual contains sections on engine repair, fuel and air repair, electrical repair, power train repair, steering and brake repair, hydraulic repair, and miscellaneous repair. It includes specifications, component locations, theory of operation, diagnosis procedures, and repair instructions. Technicians should follow all safety instructions when working on the mowers.
Caterpillar cat 325 d l excavator (prefix lal) service repair manual (lal0000...hfjsekekmmd
This document provides the disassembly procedure for a 325D L excavator travel motor. It lists 28 steps to fully disassemble the travel motor including removing the head, port plate, springs, plates, friction discs, bearing races, cam plate, piston assemblies, seals, and other components. Precautions are given to contain fluids, mark components for reinstallation, and ensure cleanliness during disassembly and assembly. Required tools are also listed.
Yale a875 glp040 060 rg-tg-zg lift truck service repair manualfhjsekkemm
This document provides a summary of the service manual contents for a lift truck. It includes 3 sentences or less summaries of sections on the frame, operator module repair, hood and side cover repair, and overhead guard repair. Procedures are provided for removing and installing major components like the operator module, hood, and overhead guard. Details are also given on adjusting the hood latch and replacing LED backup and brake lights.
Caterpillar cat 323 d2 l excavator (prefix jeg) service repair manual (jeg000...fusjejkdkmse
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the head, brake piston, barrel assembly, and shaft. The assembly section lists 14 steps, starting with cleaning components and ending by installing the cam plate and keys into the motor body. Precise alignment of parts is emphasized to ensure proper reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...jdkskmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...f8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...ufjksemd8ujd
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly process describes 24 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...prmy389342
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft. The assembly process describes 25 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...f7fujksekmdm8u
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...8ufjsekddm8u
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly process describes 24 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual Instant ...zan2736ban
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar cat 323 d2 l excavator (prefix pjp) service repair manual (pjp000...idkdkddmd
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Hyundai 20253032 bc 7 forklift truck service repair manualfjjsekmmm
This document provides instructions for disassembling and assembling the steering unit of a machine. It describes removing components like the end cover, gearwheel set, cardan shaft, distributor plate, check valve parts, thrust bearing and springs. It then explains how to reassemble these parts, including pressing in seals and springs correctly. Tools needed are also listed along with tightening torques for mounting bolts.
Hyundai 50 ds 7e forklift truck service repair manualfusjejkdkmse
This document provides an overview and outline of the sections contained in a service manual for a machine. It begins with general safety information and specifications in Section 1. Section 2 covers removal and installation procedures. Sections 3 through 8 each describe a different mechanical system of the machine, including the power train, brakes, steering, hydraulics, electrical, and mast. Each section is divided into groups covering the structure and operation, maintenance, troubleshooting, disassembly and assembly of that system. Conversion tables are also provided as a reference.
Hyundai brj series forklift truck service repair manualfjjsekmmm
This document provides an overview and outline of the service manual for a machine. It includes 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. The foreword explains the structure and purpose of the manual. It also provides guidance on how to read page numbers and file pages in the correct order. The conversion table section includes tables to enable simple conversions between units of measurement like millimeters to inches, kilograms to pounds, liters to gallons, etc.
Hyundai 250 d 7e forklift truck service repair manualfjjsekmmm
This document contains an overview and table of contents for a service manual for an unspecified machine. It outlines 8 sections that will be covered in the manual, including general information, removal/installation procedures, descriptions of the power train, brake, steering, hydraulic, and electrical systems, and the mast. The foreword provides information on how the manual is organized and formatted. It is intended to help technicians properly service the machine by providing accurate technical information and instructions.
Hyundai 30 df forklift truck service repair manualfjjsekmsmmes
The document describes the power train system of a vehicle. It includes the engine, transmission, drive shaft, drive axle, and brakes. The transmission uses a torque converter and power shift transmission to transfer power from the engine to the drive axle. It includes a control valve that regulates oil pressure and directs it to engage either the forward or reverse clutch, allowing the vehicle to shift gears automatically based on engine speed. The transmission case houses the transmission components and control valve, and includes an oil filter and parking brake.
Kubota v3600 t-e3 b diesel engine service repair manualfusjejkdkmse
This document provides service technicians with information on servicing and maintaining various Kubota diesel engine models. It is divided into three parts covering general information, engine mechanisms, and servicing procedures.
The general section includes instructions on identifying engine models, general safety precautions, maintenance checklists, and maintenance schedules. Technicians are advised to check specific components and systems daily, every 50 hours, 250 hours, 500 hours, and longer intervals. The document also lists special tools needed for servicing tasks.
This document is a service manual for MerCruiser GM 4 cylinder 181 cid (3.0L) marine engines. It provides information on engine components, maintenance procedures, troubleshooting, removal and installation of engine systems, and specifications. Safety notices are included throughout to warn technicians of hazards.
Caterpillar cat 930 r wheel loader (prefix 57z) service repair manual (57z040...fujskekfmsme
This document provides instructions for installing the fuel injection pump housing and governor on a Caterpillar 930T wheel loader. It describes:
1) Using an engine turning tool to find the top center position of the No. 1 piston by turning the flywheel and installing a bolt in a hole in the flywheel.
2) Installing fuel pump timing pins and checking that the fuel injection pump gear teeth are aligned with the timing marks on the housing.
3) Installing the fuel injection pump housing and governor, and checking that the governor shaft turns freely once assembled.
Hyundai hdf15 3 forklift truck service repair manualfjjsekmmm
This document outlines the contents and structure of a service manual for a machine. It includes 8 sections that cover general information, removal and installation of components, power train, brake, steering, hydraulic, electrical, and mast systems. Each section contains groups that provide details on the structure, operation, troubleshooting, testing, and disassembly/assembly of the various systems. Specifications, conversions charts for measurements, and a temperature conversion table are also included at the beginning.
John deere f911 front mower service repair manualfjjskdmnenemm
This technical manual provides service information for John Deere F911, F915, F925, F932, and F935 front mowers. The manual contains sections on engine repair, fuel and air repair, electrical repair, power train repair, steering and brake repair, hydraulic repair, and miscellaneous repair. It includes specifications, component locations, theory of operation, diagnosis procedures, and repair instructions. Technicians should follow all safety instructions when working on the mowers.
Caterpillar cat 325 d l excavator (prefix lal) service repair manual (lal0000...hfjsekekmmd
This document provides the disassembly procedure for a 325D L excavator travel motor. It lists 28 steps to fully disassemble the travel motor including removing the head, port plate, springs, plates, friction discs, bearing races, cam plate, piston assemblies, seals, and other components. Precautions are given to contain fluids, mark components for reinstallation, and ensure cleanliness during disassembly and assembly. Required tools are also listed.
Yale a875 glp040 060 rg-tg-zg lift truck service repair manualfhjsekkemm
This document provides a summary of the service manual contents for a lift truck. It includes 3 sentences or less summaries of sections on the frame, operator module repair, hood and side cover repair, and overhead guard repair. Procedures are provided for removing and installing major components like the operator module, hood, and overhead guard. Details are also given on adjusting the hood latch and replacing LED backup and brake lights.
Caterpillar cat 323 d2 l excavator (prefix jeg) service repair manual (jeg000...fusjejkdkmse
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the head, brake piston, barrel assembly, and shaft. The assembly section lists 14 steps, starting with cleaning components and ending by installing the cam plate and keys into the motor body. Precise alignment of parts is emphasized to ensure proper reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...jdkskmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...f8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...ufjksemd8ujd
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly process describes 24 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...prmy389342
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft. The assembly process describes 25 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...f7fujksekmdm8u
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...8ufjsekddm8u
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly process describes 24 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual Instant ...zan2736ban
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar cat 323 d2 l excavator (prefix pjp) service repair manual (pjp000...idkdkddmd
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove all components of the travel motor. Key steps include removing the head, brake piston, barrel assembly, shoe retainer and piston shoe assemblies. The assembly process reverses the disassembly with 27 corresponding steps and provides details on cleaning, lubricating and installing each part in the proper orientation and location. Special tools and precautions are noted throughout.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual Instant ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly process describes 24 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual (PJP0000...km7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly process describes 24 steps and includes applying sealant and oil, and ensuring proper alignment of components like the cam plate and keys during installation. Special care must be taken to avoid damaging parts and ensure correct positioning of pieces like the cam plate.
Caterpillar Cat 323D2 L Excavator (Prefix PJP) Service Repair Manual Instant ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft. The assembly process describes 24 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and not allowing parts to fall apart during disassembly and assembly.
Caterpillar cat 323 d2 l excavator (prefix pjp) service repair manual (pjp000...fjkskekxsdcmdmme
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process involves 27 steps to remove components such as the motor head, check valves, fittings, brake piston, friction plates, barrel assembly, and shaft assembly. The assembly process describes 24 steps and requires cleaning and lubricating components before reinstalling them in the reverse order of disassembly. Special care must be taken with alignment marks and component positions during reassembly.
Caterpillar cat 323 d2 l excavator (prefix ycr) service repair manual (ycr000...fjkskekxsdcmdmme
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, check valves, fittings, piston guide, brake piston, barrel assembly and more. The assembly section lists 24 steps to reinstall these components in reverse order, noting proper orientation and cleaning of parts. Precautions are provided to avoid damage and ensure correct installation of components like the cam plate and piston shoe assemblies.
Caterpillar Cat 323D2 L Excavator (Prefix YCR) Service Repair Manual (YCR0000...ufjksemd8ujd
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the head, brake piston, barrel assembly, shoe retainer, and shaft. The assembly section outlines 13 steps including installing seals, the shaft assembly, cam plate, and barrel components. Special care must be taken to mark parts for proper reinstallation and not damage mating surfaces during disassembly.
Caterpillar Cat 323D2 L Excavator (Prefix YCR) Service Repair Manual (YCR0000...jdkskmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, check valves, fittings, brake piston, friction plates, barrel assembly and shaft. The assembly process describes 25 steps and includes applying sealant, installing seals, plates, springs and other components in the correct order and orientation. Special care must be taken with keys and pins to prevent damage during assembly.
Caterpillar Cat 323D2 L Excavator (Prefix YCR) Service Repair Manual (YCR0000...prmy389342
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, check valves, fittings, brake piston, friction plates, barrel assembly and shaft. The assembly process describes 25 steps and includes applying sealant, installing seals, plates, springs and other components in the correct order and orientation. Special care must be taken with keys and pins to prevent damage during assembly.
Caterpillar Cat 323D2 L Excavator (Prefix YCR) Service Repair Manual (YCR0000...f8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, check valves, fittings, brake piston, friction plates, barrel assembly and shaft. The assembly process describes 25 steps and includes precautions to ensure proper installation of components like the cam plate, piston shoe assemblies, keys and seals. Special tools and clean hydraulic oil are required for the assembly.
Caterpillar Cat 323D2 L Excavator (Prefix YCR) Service Repair Manual Instant ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, check valves, fittings, brake piston, friction plates, barrel assembly and shaft. The assembly process describes 25 steps and includes precautions to ensure correct installation of components like the cam plate, piston shoe assemblies, keys and seals. Special tools and clean hydraulic oil are required for the assembly.
Similar to Caterpillar cat 323 d2 l excavator (prefix jeg) service repair manual (jeg00001 and up) (20)
Kubota v3800 di t-e3cb diesel engine service repair manualidkdkddmd
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then lists general precautions and a maintenance checklist. The bulk of the document provides detailed checklists for various maintenance intervals, from daily checks to every 3000 hours. It concludes with an overview of special tools needed for servicing.
Kubota v3800 di t-e3bg diesel engine service repair manualidkdkddmd
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then lists general precautions and a maintenance checklist. The bulk of the document provides detailed checklists for periodic maintenance at intervals such as every 50 hours, 250 hours, and yearly. It concludes with a list of special tools needed for servicing.
Kubota v3800 di t-e3b diesel engine service repair manualidkdkddmd
This document provides information for servicing personnel on servicing and maintaining various Kubota diesel engine models. It is divided into three parts: General, Mechanism, and Servicing. The General section provides engine identification and safety information. The Mechanism section describes the engine construction and function. The Servicing section provides troubleshooting, maintenance, and repair procedures and specifications. The manual is intended to provide technicians with the information needed to service the specified Kubota diesel engine models.
Kubota v3600 t-e3 cb diesel engine service repair manualidkdkddmd
This document provides information on servicing Kubota diesel engines, including V3600-E3B, V3600-T-E3B, and V3800DI-T-E3B models. It is divided into three parts: General, Mechanism, and Servicing.
The General section includes engine identification information, general precautions, maintenance checklists, and maintenance schedules. The Mechanism section describes the engine construction and functions. The Servicing section provides troubleshooting, specification lists, disassembly/assembly procedures, and other servicing information. The document is intended to provide technicians with service and maintenance information to work on these engine models.
Kubota v3600 t-e3 bg diesel engine service repair manualidkdkddmd
This document provides information for servicing personnel on servicing and maintaining various Kubota diesel engine models. It is divided into three parts: General, Mechanism, and Servicing. The General section provides engine identification and safety information. The Mechanism section describes the engine construction and function. The Servicing section provides troubleshooting, maintenance, and repair procedures and specifications. The manual is intended to provide technicians with the information needed to service the specified Kubota diesel engine models.
Kubota v3600 t-e3 b diesel engine service repair manualidkdkddmd
This document provides information on servicing Kubota diesel engines, including V3600-E3B, V3600-T-E3B, and V3800DI-T-E3B models. It is divided into three parts: General, Mechanism, and Servicing.
The General section includes engine identification information, general precautions, maintenance checklists, and maintenance schedules. The Mechanism section describes the engine construction and functions. The Servicing section provides troubleshooting, specification lists, disassembly/assembly procedures, and other servicing information. The document is intended to provide technicians with service and maintenance information to work on these engine models.
Kubota v3600 e3 cb diesel engine service repair manualidkdkddmd
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then provides general safety precautions and a maintenance checklist. The bulk of the document consists of detailed checklists for performing maintenance at regular intervals, with items to check daily, after 50 hours, every 50 hours, every 250 hours and so on. It concludes by listing special tools needed for maintenance.
Kubota v3600 e3 b diesel engine service repair manualidkdkddmd
This document provides information for servicing personnel on servicing and maintaining various Kubota diesel engine models. It is divided into three parts: General, Mechanism, and Servicing. The General section provides engine identification and safety information. The Mechanism section describes the engine construction and function. The Servicing section provides troubleshooting, maintenance, and repair procedures and specifications. The manual is intended to provide technicians with the information needed to service the specified Kubota diesel engine models.
Kubota v3300 t-e2 b diesel engine service repair manualidkdkddmd
The document provides information on servicing a diesel engine. It begins with identifying the engine model and serial number. The second part describes the engine identification codes and emission control details. The third part lists general precautions for servicing including arranging removed parts carefully, using special tools as required, and disconnecting the battery before working on live wires.
Kubota v3300 e3 bg diesel engine service repair manualidkdkddmd
This document provides information on servicing Kubota diesel engines. It begins by outlining how to identify specific engine models and serial numbers. It then lists general precautions and a maintenance checklist. The bulk of the document provides detailed checklists for various maintenance intervals, from daily checks to every 3000 hours. It concludes with an overview of special tools needed for servicing.
Kubota v3300 e2 b diesel engine service repair manualidkdkddmd
The document provides information on servicing a diesel engine. It begins with identifying the engine model and serial number. The second part describes general precautions for maintenance and servicing such as arranging removed parts carefully, using special tools as required, and disconnecting the battery before working on live wires. The third part lists maintenance check points to inspect components at regular intervals.
This document provides a summary of tractor transmission mechanisms, including:
1. Sliding mesh, constant mesh, and synchronous mesh transmission gears that transfer power from the clutch to the drive wheels.
2. Hydraulic shuttle shift and swing shift mechanisms that allow changing the direction of travel.
3. Dual speed transmission that provides two gear ratios for high and low speeds.
4. Various types of hydrostatic transmissions and glide shift transmissions that provide continuously variable speed control through hydraulic components like pumps and motors.
Hyundai 70 ds 7e forklift truck service repair manualidkdkddmd
This document provides an overview and outline of the contents of a service manual for a machine. It is divided into 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. Each section contains multiple groups that go into further detail about the structure, operation, maintenance, troubleshooting and repair of components within each system. Safety symbols are defined and instructions are provided on how to read and reference the manual, including how to interpret page numbers and use the conversion tables.
Hyundai 70 df 7 forklift truck service repair manualidkdkddmd
This document provides an overview and outline of the contents of a service manual for a machine. It includes 8 sections that cover general information, removal and installation procedures, descriptions of the power train, brake, steering, hydraulic, electrical, and mast systems. Each section includes groups that describe the structures, operations, inspections, troubleshooting, disassembly/assembly procedures, and adjustments for the various components and systems. Conversion tables are also provided at the end to allow simple conversions between different units of measurement.
Hyundai 70 d 7e forklift truck service repair manualidkdkddmd
This document provides instructions for disassembling and assembling a steering unit. It includes diagrams labeling the parts and components. The instructions describe how to remove parts like the end cover, gearwheel set, cardan shaft, distributor plate, check valve, bearing races and thrust bearing. Reassembly instructions provide details on installing parts like the spool, sleeve, cross pin, neutral position springs, O-rings and lip seal in the correct order and orientation. Torque specifications are also provided for mounting bolts.
Hyundai 60 ds 7e forklift truck service repair manualidkdkddmd
This document provides an overview and outline of the contents of a service manual for a machine. It is divided into 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. Each section contains multiple groups that go into further detail about the structure, operation, maintenance, troubleshooting and repair of components within each system. Safety symbols are defined and instructions are provided on how to read and reference the manual, including how to interpret page numbers and use the conversion tables.
Hyundai 60 df 7 forklift truck service repair manualidkdkddmd
This document provides an overview and table of contents for a service manual. It outlines the general safety information covered in Section 1 and describes the contents of Sections 2 through 8, which cover the removal and installation of components, various mechanical systems including power train, brakes, steering, hydraulics, and electrical, and the mast. The document explains how to read and understand the manual, including how to reference page numbers and file additional pages. It also includes conversion tables to allow simple conversions between different units of measurement.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D2 L EXCAVATOR JEG
Configuration: 323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
323D2 Excavator Machine Systems
Media Number -UENR3338-02 Publication Date -01/07/2017 Date Updated -19/07/2017
i01219550
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Start By:
a. Remove the travel motor.
Reference: Refer to Disassembly and Assembly, "Travel Motor - Remove" in this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the
travel motor is 60 kg (132 lb).
1/8
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00510326
Note: During the removal of head (2) from the body of the travel motor, be careful not to
scratch or damage the mating surfaces of the components.
4. Remove socket head bolts (1).
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00510341
2/8
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00510349
6. Turn over head (2).
7. Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head.
8. Remove the two check valve assemblies from the head.
Note: There is a retainer under spring (9). This retainer is a press fit in head (2). Do not
remove the retainer.
9. Insert a dowel rod with a small diameter into hole (X). Tap the dowel rod with a plastic
hammer in order to remove spring (9), poppet (8) and seat (7) from the head.
Illustration 4 g00510351
10. Remove three fittings (10) and plugs (11) from the head. Remove the O-ring seal from each
fitting.
Illustration 5 g00510352
11. Remove three O-ring seals (12) and washer set (13) from the body of the travel motor.
12. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply
approximately 525 kPa (75 psi) of shop air pressure to brake release port (Y). Make sure
that the shop air pressure is free of water. Brake piston (14) will move up the piston guide,
and out of the piston guide. Remove brake piston (14) from the body of the travel motor.
3/8
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g00510353
13. Remove O-ring seal (15) from the brake piston. Remove backup ring (16) from the brake
piston.
14. Remove O-ring seal (17) from the brake piston. Remove backup ring (18) from the brake
piston.
Illustration 7 g00510356
15. Remove piston guide (19), five friction plates (20) and the four steel plates from the body of
the travel motor.
Illustration 8 g00510359
4/8
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. 16. Remove O-ring seal (21) from the piston guide. Remove backup ring (22) from the piston
guide.
Illustration 9 g00510365
Note: Do not allow the components of barrel assembly (23) to come apart during the
removal from the travel motor. All of the components in the barrel assembly must be
reinstalled in the component's original location.
17. Use two large screwdrivers, as shown. Slowly remove barrel assembly (23) from the body
of the travel motor. Do not allow the components to fall apart.
Illustration 10 g00510502
Note: Shoe retainer (24) and piston shoe assemblies (25) are not serviced separately. Prior
to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put
identification marks on piston shoe assemblies (25) for assembly purposes. Identification
marks are used to identify the piston shoe assembly's location in shoe retainer (24) and
barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's
original bores in the shoe retainer and the barrel.
18. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the
piston shoe assemblies from the shoe retainer.
5/8
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 11 g00510504
19. Remove guide (27), spacer (28) and springs (29) from the barrel.
Illustration 12 g00510547
20. Remove cam plate (30) from the body of the travel motor.
Illustration 13 g00510550
21. Remove two keys (31) and the two locating pins (not shown) from the body of the travel
motor.
6/8
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g00510551
22. Remove O-ring seal (33) from the body of the travel motor.
23. Use a soft faced hammer to remove shaft assembly (34) from the body of the travel motor.
Remove the shaft assembly in the direction that is indicated by the arrow. Refer to
Illustration 14.
Illustration 15 g00510595
24. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing
(36) with a press.
Illustration 16 g00510598
7/8
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 25. Remove inner race (37) from shaft (34).
Illustration 17 g00510599
26. Remove lip seal (38) from the body of the travel motor.
Illustration 18 g00510605
27. Remove two stoppers (39) and the two pistons from the body of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 23:12:05 UTC+0800 2020
8/8
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D2 L EXCAVATOR JEG
Configuration: 323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
323D2 Excavator Machine Systems
Media Number -UENR3338-02 Publication Date -01/07/2017 Date Updated -19/07/2017
i01706705
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
1. Make sure that all of the components of the travel motor are thoroughly clean and free of
dirt and debris prior to assembly.
Illustration 1 g00510595
2. Install retaining ring (35) in the groove on shaft (34).
3. Install bearing (36) on shaft (34) with a press. Install the bearing until the bearing contacts
the retaining ring.
1/10
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 4. Install the other retaining ring on the opposite side of bearing (36).
Illustration 2 g00510598
5. Install inner race (37) on the end of shaft (34) until the inner race is seated against the
shoulder on the shaft.
Illustration 3 g00651891
(a) Body
6. Apply a thin coat of 5P-3413 Pipe Sealant on Surfaces (Y) of the body of the travel motor.
7. Use Tooling (A) in order to install lip seal (38).
8. Install lip type seal (38) in the body of the travel motor. Install the lip seal so that the sealing
lip is facing in the direction that is shown. Make sure that the lip seal contacts the
counterbore in the body of the travel motor.
Note: Slowly rotate shaft assembly (34) during the installation in order to make sure that the
shaft assembly does not bind in the body of the travel motor.
9. Apply clean hydraulic oil on the lip of lip seal (38).
2/10
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 10. Use a press to install shaft assembly (34) in the body of the travel motor. Slowly rotate the
shaft during the installation in order to make sure that the shaft does not bind. Make sure
that the bearing on the shaft contacts the counterbore in the body of the travel motor.
Illustration 4 g00651960
NOTICE
The locating pin on each key is not centered. In order to prevent
damage to the barrel assembly during assembly of the travel motor, the
keys must be installed as shown. Also, the keys must be installed in the
key's original location in the body of the travel motor.
11. Install the two locating pins and two keys (31) in the body of the travel motor, as shown.
Illustration 5 g00510547
3/10
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 12. Install cam plate (30) in the body of the travel motor in the cam plate's original location.
Make sure that the two pistons and two keys (31) in the body of the travel motor engage
properly with the cam plate.
Illustration 6 g00510504
13. Install nine springs (29) in the barrel. Install spacer (28) and guide (27) on the barrel.
Illustration 7 g00878253
14. Install piston shoe assemblies (25) in the piston shoe assembly's original bores in shoe
retainer (24).
15. Apply clean hydraulic oil in the bores of the barrel and on piston shoe assemblies (25).
Install the piston shoe assemblies with the shoe retainer in the piston shoe assembly's
original bore in barrel (26).
NOTICE
Make sure that the cam plate is correctly engaged with the two pistons
in the body of the travel motor prior to installing the barrel assembly.
When the body of the travel motor is tilted to allow the installation of
the barrel assembly, the cam plate can slide off of the two pistons. The
remaining parts of the travel motor can be assembled with the cam
plate in the incorrect position.
4/10
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Extensive damage will result from the incorrect installation of the cam
plate. Follow the exact installation procedure to prevent damage.
16. Apply clean hydraulic oil on the sliding surfaces of the cam plate, on the piston shoe
assemblies and on the splined shaft of the travel motor.
Illustration 8 g00485953
17. Route a piece of strong string through an opening for the cam plate tension adjusters. Route
the string over the sliding surface of cam plate (30) and through the opposite opening for the
cam plate tension adjusters. Hold the string taut in order to keep cam plate (30) correctly
engaged with keys (31). Keep the string taut and position the body of the travel motor on the
body's side. Do not release the tension on the string at this time. Install barrel assembly (23)
as a unit on the shaft. Pull the string out of the body of the travel motor. It may be necessary
to pull the barrel assembly and the piston shoe assemblies away from the cam plate slightly
in order to release the string.
Illustration 9 g00651967
5/10
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 18. Install O-ring seal (21) and backup ring (22) on piston guide (19), as shown.
Illustration 10 g00510356
19. Place the body of the travel motor in a vertical position.
20. Apply clean hydraulic oil on five friction plates (20) and the four steel plates. Install the
plates in alternating order in the body of the travel motor. Start with a friction plate and end
with a friction plate.
21. Install piston guide (19) in the body of the travel motor until the piston guide contacts the
counterbore in the body of the travel motor.
Illustration 11 g00878297
Note: Make sure that brake piston (14) is thoroughly clean and free of dirt and debris.
22. Install O-ring seal (16). Install backup ring (15).
23. Install O-ring seal (17). Install backup ring (18).
6/10
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 24. Apply a thin coat of hydraulic oil on the surfaces of piston (14) which contact the body of
the travel motor. Install piston (14) in the body of the travel motor by hand. It may be
necessary to use a soft faced hammer to seat the piston correctly.
Illustration 12 g00878299
Illustration 13 g00878239
25. Install washer set (12) in piston (14), as shown.
26. Install O-ring seals (13) in the body of the travel motor, as shown.
7/10
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 14 g00510605
27. Install the two pistons and two stoppers (39) in the housing of the travel motor. Tighten the
stoppers to a torque of 140 ± 14 N·m (105 ± 10 lb ft).
Illustration 15 g00510351
28. Install the O-ring seals on fittings (10). Apply 5P-3413 Pipe Sealant on the threads of
fittings (10). Install the fittings in the head, as shown.
29. Install plugs (11) in the head. Tighten each plug to a torque of 15 ± 2 N·m (11 ± 1 lb ft).
Illustration 16 g00510349
8/10
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 17 g00510341
30. Apply a thin coat of 9S-3263 Thread Lock Compound on the threads of the two check
valves. Install the check valves in the head.
31. Install seat (7), poppet (8) and spring (9) in the head at Location (X).
32. Install O-ring seal (6) in the head, as shown.
33. Install bearing (3) in the head until the bearing contacts the counterbore in the cover.
34. Apply 1U-6396 O-Ring Assembly Compound on port plate (4). Install the port plate in the
port plate's original position on the motor cover.
35. Use a shim or shims (5) so that the following requirements are met.
Note: During the following checks, turn the travel motor output shaft in a clockwise
direction.
a. The travel motor output shaft does not rotate with an applied torque of 440 N·m
(325 lb ft) or more with the parking brake release port open.
b. The travel motor output shaft rotates with an applied torque of 29 N·m (21 lb ft) or
less when the parking brake release port is pressurized to 780 kPa (115 psi) with both
the inlet port and the outlet port open to the hydraulic oil tank.
Note: It may be necessary to remove head (2) several times in order to determine the correct
thickness of shim or shims (5) that are used to adjust the rolling torque of the travel motor
output shaft.
36. Apply a thin layer of 5P-0960 Molybdenum Grease on shim or shims (5). Install the shim or
shims on the head. The grease will hold the shim or shims in place during the installation of
the head. Install the head on the body of the travel motor.
9/10
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 18 g00510326
37. Place head (2) in the head's original position on the travel motor. Install socket head bolts
(1) that secure the head. Tighten the socket head bolts to a torque of 175 ± 18 N·m
(130 ± 13 lb ft).
NOTICE
To prevent possible damage to the travel motor, fill the unit with oil at
least to the fill port before operating the machine. Refer to the
Operation and Maintenance Manual for the correct oil specification.
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install" in this
manual.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 23:13:04 UTC+0800 2020
10/10
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEB...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D2 L EXCAVATOR JEG
Configuration: 323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
323D2 Excavator Machine Systems
Media Number -UENR3338-02 Publication Date -01/07/2017 Date Updated -19/07/2017
i03524320
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded Rod M16 by 381mm 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/3
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g00651795
2. Install a new O-ring seal (5) . Apply clean hydraulic oil on O-ring seal (5) .
Illustration 2 g00707267
3. Attach a suitable lifting device to travel motor (4) , as shown. The weight of travel motor (4)
is approximately 57 kg (125 lb).
Illustration 3 g00944825
2/3
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 4. Carefully install travel motor (4) on Tooling (A) . Slide travel motor (4) into the final drive.
5. Install bolt (2A) that secures travel motor (4) to the final drive.
6. Remove Tooling (A) .
Illustration 4 g00707275
Typical example
7. Install bolts (2) .
8. Connect hose assemblies (3) and (1) .
9. Fill the final drive with oil. Refer to Operation and Maintenance Manual, "Lubricant
Viscosities" for the proper oil viscosity. Refer to Operation and Maintenance Manual, "Final
Drive Oil Level - Check" for the correct filling procedure.
10. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
11. Obtain a hydraulic oil sample from the main S·O·S port. Refer to Operation and
Maintenance Manual, "Sampling Interval and Location of Sampling Valve" for the correct
location.
12. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system. Refer to Contamination
Control Guideline, SEBF8447 for further information.
End By: Install the counterbalance valve. Refer to Disassembly and Assembly, "Counterbalance
Valve (Travel) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 23:14:04 UTC+0800 2020
3/3
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D2 L EXCAVATOR JEG
Configuration: 323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
323D2 Excavator Machine Systems
Media Number -UENR3338-02 Publication Date -01/07/2017 Date Updated -19/07/2017
i05453056
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C
154-6184 Forcing Bolt (M 20) 2
154-6185(1)
Forcing Bolt (M 24) 2
(1)
For Use on 329 and 330 sales models
Start By:
a. Separate the track assembly.
b. Remove the travel motor.
1/3
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Illustration 1 g00489826
Typical Example
Note: Adjust the height of Tooling (A) so that there is sufficient clearance between the
sprocket and the track for the removal of the final drive.
1. Lift the side of the machine in order to install Tooling (A) under the frame, as shown.
Illustration 2 g00712767
2. Fasten Tooling (B) and a suitable lifting device to final drive (1), as shown. Put a slight
lifting tension on the final drive.
Illustration 3 g00712737
2/3
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Note: Mark the orientation of bolt holes (2) for the travel motor for installation purposes.
3. Remove bolts (3) and the washers from the final drive.
Illustration 4 g00712749
4. Use Tooling (C) in order to remove the final drive from the frame.
5. Carefully remove final drive (1). The weight of final drive (1) and the sprocket is
approximately 312 kg (688 lb).
6. Remove Tooling (C) from the frame.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 15 23:15:03 UTC+0800 2020
3/3
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D2 L EXCAVATOR JEG
Configuration: 323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
323D2 Excavator Machine Systems
Media Number -UENR3338-02 Publication Date -01/07/2017 Date Updated -19/07/2017
i02606369
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 154-6181 Forcing Screw 1
D 138-7574 Link Bracket 2
E
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F 1U-8846 Gasket Sealant 1
Start By:
a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".
1/11
323D2 L Excavator JEG00001-UP (MACHINE) POWERED BY C7.1 Engine(SEBP6...
2020/9/15
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...