The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
- Removing and installing the crankshaft vibration damper and pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing and installing the front cover.
- Removing and installing the front housing.
The summaries provide the high level steps for removing and installing the listed components from the Caterpillar service manual in 3 sentences or less.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...fujsfskekem
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...uudfjjjskkemmd
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...uujjfjjkskmme
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...fujsjefskekmm
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...yhfhjjkdksmme
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...ujjfdjkjskkmdm
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...fujsjefkksekmme
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...fujsefjfkksekem
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...fujsfskekem
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...uudfjjjskkemmd
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...uujjfjjkskmme
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...fujsjefskekmm
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...yhfhjjkdksmme
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...ujjfdjkjskkmdm
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c l hydraulic excavator (prefix emr) service repair manua...fujsjefkksekmme
The document provides instructions for removing and installing the camshaft idler on a Caterpillar 3126B engine. The removal procedure involves removing bolts to access the idler gear. The installation procedure specifies applying sealant and installing the idler gear with bolts, tightening them to the specified torque.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...fujsefjfkksekem
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...yhfhjjkdksmme
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...yushantuanjing
This document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It describes how to:
1. Remove the crankshaft vibration damper, pulley, and belt.
2. Remove the front cover by taking off mounting bolts and brackets.
3. Remove the front housing by taking off engine mountings and supports.
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing, which requires removing other components like the alternator first.
3. Cleaning and applying sealant when installing the front housing.
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing, which requires draining fluids first.
3. Cleaning and applying sealant when reinstalling the front housing.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...sijipang18046
This document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It describes how to:
1. Remove the crankshaft vibration damper, pulley, and belt.
2. Remove the front cover by taking off mounting bolts and brackets.
3. Remove the front housing by taking off engine mountings and supports.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...r8qvui4a
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing and installing new gaskets.
3. Procedures for removing and installing the camshaft and front crankshaft seal.
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing and installing new gaskets.
3. Procedures for removing and installing the camshaft and front crankshaft seal.
Caterpillar Cat 322C FM EXCAVATOR (Prefix M2H) Service Repair Manual (M2H0000...jfksemmdm3e
This document provides instructions for removing and installing the camshaft idler gear on a Caterpillar 3126B engine. The removal procedure involves rotating the crankshaft to align timing marks, removing mounting bolts and plates, and pressing the bearing out of the idler gear. The installation procedure specifies cleaning parts, pressing the bearing into the idler gear, positioning the idler shaft and securing with a bolt, and aligning timing marks. Tools include a driver and press. Proper containment of fluids is emphasized.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft. Safety notes are included to warn of potential injury from improper assembly of spring-loaded parts.
The document provides instructions for removing and installing various components of a Caterpillar 992K wheel loader, including:
1) Removing and disassembling the rear power take-off, which involves using various tools to remove nuts, bearings, and other parts.
2) Instructions for reassembling the rear power take-off by installing bearings and other components in the reverse order of disassembly.
3) Procedures for removing and installing the vibration damper and pulley, which includes using guide studs and lifting equipment to handle the heavy components.
The document contains detailed step-by-step instructions along with illustrations to correctly perform maintenance on specific parts of the 992K
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
This document provides instructions for removing and disassembling the transmission of a 416D Backhoe Loader. It outlines 14 steps to remove the transmission, which includes draining fluids, removing mounting bolts, and lowering the transmission. It then details disassembling the transmission into its major components, such as removing the front and rear output shafts, planetary gears, clutch packs, seals, and bearings. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
The document provides instructions for removing and installing the fuel transfer pump on a Caterpillar 322N excavator powered by a 3116 engine. It details removing the pump cover, spring, piston and seals. It also describes inspecting parts and lubricating them with oil during installation. Installation involves reversing the removal steps and ensuring proper alignment of components.
The document provides instructions for removing and installing final drive sprockets, travel brake valves, and travel motors on a 322-A excavator model. Key steps include separating the track assemblies, using tools to support heavy components like the sprocket while removing fasteners, cleaning mating surfaces, replacing seals, and torquing fasteners to the specified values. The process also requires draining oil from the final drive and hydraulic system before removing components.
This document provides instructions for disassembling the control valve (auxiliary) on a 322C excavator. It describes removing and disassembling various components of the control valve such as solenoid valves, line relief valves, fittings, seals, and spools. Cleanliness is emphasized to prevent contamination of hydraulic systems during disassembly and reassembly. Detailed illustrations and part numbers are provided for each step. Personal protective equipment is recommended when removing or releasing parts under spring pressure.
Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...udjkskdmmd
This document provides instructions for removing and installing a governor from a 322 L, 322 LN, and 322 N excavator powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and tubes connecting the governor to the engine. Individual parts like O-rings and seals must be removed and replaced. The installation procedure specifies lubricating new seals and using tools to reconnect everything in the reverse order of removal. Special attention is given to properly adjusting the fuel setting after installing the new governor.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...udjkskdmmd
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
- Removing and installing the crankshaft vibration damper and pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing and installing the front cover.
- Removing and installing the front housing.
The summaries provide the high level steps for removing and installing the listed components from the 3126B engine in 3 sentences or less per the request.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
This document provides instructions for removing and installing various engine components on a Caterpillar 993K wheel loader, including:
- Inlet and exhaust valves, guides, and seat inserts
- Engine oil filter base
- Engine oil cooler
The procedures describe using various tools to remove parts like the cylinder head, valves, guides, filters, hoses, and the oil cooler assembly. Installation is generally the reverse of removal, with instructions to clean parts, apply sealant or lubricant, and torque fasteners to the specified values. Safety notices warn of spring hazards and keeping parts clean to prevent wear.
This document provides instructions for removing and installing various components of the rear power take-off (RPTO) and vibration damper on a 993K wheel loader. It describes in detail how to disassemble the RPTO by removing nuts, bearings, and gears. It then explains the reverse process to assemble the RPTO. Separate sections provide procedures for installing the RPTO and removing/installing the vibration damper and pulley, including the use of various tools. Detailed illustrations accompany each step.
This document provides instructions for disassembling and assembling the parking brake on a Caterpillar 993K Wheel Loader. It describes removing 16 different components of the parking brake including pistons, springs, discs, plates, and housings. Detailed illustrations and torque specifications are provided for each step of disassembly and assembly. Tools required include a slide hammer, puller, driver group, link brackets, lever puller hoist, and sealant. Personnel safety warnings and proper procedures are noted throughout.
More Related Content
Similar to Caterpillar Cat 322C LN Hydraulic Excavator (Prefix EMR) Service Repair Manual Instant Download.pdf
Caterpillar cat 322 c ln hydraulic excavator (prefix emr) service repair manu...yhfhjjkdksmme
The document provides instructions for removing and installing various engine components on a Caterpillar 322C L and 322C LN hydraulic excavator. It describes:
1. Removing the crankshaft vibration damper, pulley, and belt.
2. Removing the crankshaft front seal by drilling holes in it and pulling it out with a slide hammer tool.
3. Removing the front cover and housing by removing mounting bolts.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...yushantuanjing
This document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It describes how to:
1. Remove the crankshaft vibration damper, pulley, and belt.
2. Remove the front cover by taking off mounting bolts and brackets.
3. Remove the front housing by taking off engine mountings and supports.
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing, which requires removing other components like the alternator first.
3. Cleaning and applying sealant when installing the front housing.
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing, which requires draining fluids first.
3. Cleaning and applying sealant when reinstalling the front housing.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...sijipang18046
This document provides instructions for removing and installing various engine components on a Caterpillar 322C excavator. It describes how to:
1. Remove the crankshaft vibration damper, pulley, and belt.
2. Remove the front cover by taking off mounting bolts and brackets.
3. Remove the front housing by taking off engine mountings and supports.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...r8qvui4a
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing and installing new gaskets.
3. Procedures for removing and installing the camshaft and front crankshaft seal.
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
1. Removing and installing the crankshaft vibration damper, pulley, and front seal.
2. Removing the front cover and housing and installing new gaskets.
3. Procedures for removing and installing the camshaft and front crankshaft seal.
Caterpillar Cat 322C FM EXCAVATOR (Prefix M2H) Service Repair Manual (M2H0000...jfksemmdm3e
This document provides instructions for removing and installing the camshaft idler gear on a Caterpillar 3126B engine. The removal procedure involves rotating the crankshaft to align timing marks, removing mounting bolts and plates, and pressing the bearing out of the idler gear. The installation procedure specifies cleaning parts, pressing the bearing into the idler gear, positioning the idler shaft and securing with a bolt, and aligning timing marks. Tools include a driver and press. Proper containment of fluids is emphasized.
Similar to Caterpillar Cat 322C LN Hydraulic Excavator (Prefix EMR) Service Repair Manual Instant Download.pdf (8)
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft. Safety notes are included to warn of potential injury from improper assembly of spring-loaded parts.
The document provides instructions for removing and installing various components of a Caterpillar 992K wheel loader, including:
1) Removing and disassembling the rear power take-off, which involves using various tools to remove nuts, bearings, and other parts.
2) Instructions for reassembling the rear power take-off by installing bearings and other components in the reverse order of disassembly.
3) Procedures for removing and installing the vibration damper and pulley, which includes using guide studs and lifting equipment to handle the heavy components.
The document contains detailed step-by-step instructions along with illustrations to correctly perform maintenance on specific parts of the 992K
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
This document provides instructions for removing and disassembling the transmission of a 416D Backhoe Loader. It outlines 14 steps to remove the transmission, which includes draining fluids, removing mounting bolts, and lowering the transmission. It then details disassembling the transmission into its major components, such as removing the front and rear output shafts, planetary gears, clutch packs, seals, and bearings. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
The document provides instructions for removing and installing the fuel transfer pump on a Caterpillar 322N excavator powered by a 3116 engine. It details removing the pump cover, spring, piston and seals. It also describes inspecting parts and lubricating them with oil during installation. Installation involves reversing the removal steps and ensuring proper alignment of components.
The document provides instructions for removing and installing final drive sprockets, travel brake valves, and travel motors on a 322-A excavator model. Key steps include separating the track assemblies, using tools to support heavy components like the sprocket while removing fasteners, cleaning mating surfaces, replacing seals, and torquing fasteners to the specified values. The process also requires draining oil from the final drive and hydraulic system before removing components.
This document provides instructions for disassembling the control valve (auxiliary) on a 322C excavator. It describes removing and disassembling various components of the control valve such as solenoid valves, line relief valves, fittings, seals, and spools. Cleanliness is emphasized to prevent contamination of hydraulic systems during disassembly and reassembly. Detailed illustrations and part numbers are provided for each step. Personal protective equipment is recommended when removing or releasing parts under spring pressure.
Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...udjkskdmmd
This document provides instructions for removing and installing a governor from a 322 L, 322 LN, and 322 N excavator powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and tubes connecting the governor to the engine. Individual parts like O-rings and seals must be removed and replaced. The installation procedure specifies lubricating new seals and using tools to reconnect everything in the reverse order of removal. Special attention is given to properly adjusting the fuel setting after installing the new governor.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...udjkskdmmd
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
- Removing and installing the crankshaft vibration damper and pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing and installing the front cover.
- Removing and installing the front housing.
The summaries provide the high level steps for removing and installing the listed components from the 3126B engine in 3 sentences or less per the request.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
This document provides instructions for removing and installing various engine components on a Caterpillar 993K wheel loader, including:
- Inlet and exhaust valves, guides, and seat inserts
- Engine oil filter base
- Engine oil cooler
The procedures describe using various tools to remove parts like the cylinder head, valves, guides, filters, hoses, and the oil cooler assembly. Installation is generally the reverse of removal, with instructions to clean parts, apply sealant or lubricant, and torque fasteners to the specified values. Safety notices warn of spring hazards and keeping parts clean to prevent wear.
This document provides instructions for removing and installing various components of the rear power take-off (RPTO) and vibration damper on a 993K wheel loader. It describes in detail how to disassemble the RPTO by removing nuts, bearings, and gears. It then explains the reverse process to assemble the RPTO. Separate sections provide procedures for installing the RPTO and removing/installing the vibration damper and pulley, including the use of various tools. Detailed illustrations accompany each step.
This document provides instructions for disassembling and assembling the parking brake on a Caterpillar 993K Wheel Loader. It describes removing 16 different components of the parking brake including pistons, springs, discs, plates, and housings. Detailed illustrations and torque specifications are provided for each step of disassembly and assembly. Tools required include a slide hammer, puller, driver group, link brackets, lever puller hoist, and sealant. Personnel safety warnings and proper procedures are noted throughout.
The document provides instructions for disassembling and assembling the torque converter of a 966F wheel loader. It describes 31 steps to disassemble the various components of the torque converter including removing housing bolts, gears, bearings, seals, and other parts. It then describes 26 steps for reassembling the torque converter components in reverse order, noting specific alignment and torque specifications. The overall document provides detailed technical instructions for maintenance personnel to fully disassemble and reassemble the machine's torque converter.
The document provides instructions for disassembling and assembling the service brake on a Caterpillar 993K wheel loader. The disassembly procedure involves removing reaction plates, discs, springs, pistons, seals and other brake components. The assembly procedure describes installing these components in reverse order and applying grease and torques as specified. Safety precautions are provided to prevent injury from spring forces.
The document provides instructions for servicing components of a Caterpillar 3306 engine, including:
- Installing and removing fuel injection nozzles
- Disassembling and assembling the fuel ratio control
- Removing and installing the fuel shutoff solenoid
The instructions include diagrams illustrating the components and numbered steps for disassembly, cleaning, inspection, and reassembly of the parts. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the swing drive of a M325C MH wheeled excavator. It lists 31 steps for disassembly, removing components like the cover, carrier assembly, gears, shafts, and seals. It then lists 35 steps for assembly, installing these components in reverse order along with tools needed and special instructions. Precautions are given to contain fluids, clean parts thoroughly, and use lifting devices due to component weights up to 310 kg.
This document provides instructions for disassembling the front final drive, carrier, hubs, and brakes of an M320 Excavator. It outlines 28 steps to remove components like the planetary carrier, sun gear, ring gear, brake piston, hub, bearings and seals. Various tools are required including retaining ring pliers, pullers, wrenches and adapters. Safety notices are included about containing fluids, releasing hydraulic pressure and avoiding damage during disassembly.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02370081
Vibration Damper and Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Illustration 1 g00612677
1. Remove bolts (2), crankshaft vibration damper (1), and the spacers from the crankshaft
pulley.
1/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 2 g00612684
2. Remove belt (3). Refer to Operation and Maintenance Manual, "Belt - Inspect".
3. Remove bolts (4).
4. Remove crankshaft pulley (5).
Installation Procedure
Illustration 3 g00612684
1. Position crankshaft pulley (5) on the crankshaft. Install bolts (4) and tighten the bolts to a
torque of 160 ± 30 N·m (118 ± 22 lb ft).
2. Install belt (3). Refer to Operation and Maintenance Manual, "Belt - Inspect".
Note: Check the alignment marks on the rubber vibration dampers for proper alignment.
The rubber vibration damper should be replaced if the rubber vibration damper is out of
alignment. Refer to Specifications, "Vibration Damper".
2/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00612677
3. Install the spacers and crankshaft vibration damper (1). Install bolts (2) and tighten to a
torque of 55 ± 10 N·m (40 ± 7 lb ft).
4. Adjust the tension of the belt. Refer to Specifications, "Belt Tension Chart".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:10:23 UTC+0800 2019
3/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01982085
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B 1U-8145 Drill Bit 1
Start By:
a. Remove the vibration damper and the pulley. Refer to Disassembly and Assembly,
"Vibration Damper and Pulley - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00989224
1. Use Tooling (B) and carefully drill three evenly spaced holes in crankshaft front seal (1).
2. Alternate between the drilled holes and use Tooling (A) to remove crankshaft front seal (1).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:11:19 UTC+0800 2019
2/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01982092
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
C 1U-7430 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00989228
1. Use Tooling (C) to install crankshaft front seal (1).
Note: The crankshaft seal is designed to be installed dry.
End By:
a. Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration
Damper and Pulley - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:12:15 UTC+0800 2019
2/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01379367
Front Cover - Remove
SMCS - 1166-011
Removal Procedure
Start By:
a. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g00728351
1. Remove four bolts (1) that fasten bracket (2) on the front of the engine.
Illustration 2 g00728369
2. Remove the bolts (3) and front cover (4) from the front housing.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:13:10 UTC+0800 2019
2/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01379400
Front Cover - Install
SMCS - 1166-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The rear face of the cover and the front face of the housing must be clean.
1. Inspect the condition of the housing cover gasket. Replace the gasket, if necessary.
1/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00728369
2. Install the housing cover gasket.
3. Position front cover (4) on the front housing. Install the bolts (3) on front cover (4).
Illustration 2 g00728351
4. Position bracket (2) on the front of the engine.
5. Install four bolts (1) that fasten bracket (2) on the engine.
End By:
a. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:14:06 UTC+0800 2019
2/2
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01983906
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front
Seal - Remove".
b. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove".
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g01028155
2. Remove belt tightener (2).
3. Remove front housing (3).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:15:02 UTC+0800 2019
3/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01983976
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-9011 Component Cleaner 1
B 4C-9500 Quick Cure Primer 1
C 1U-8846 Gasket Sealant 1
1/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01028155
1. Clean the joint face on front housing (3) with Tooling (A).
2. Apply Tooling (B) to the joint face. Allow the primer to dry for at least three to five
minutes.
Note: Do not allow Tooling (C) to seal the main oil passage on front housing (3).
3. Apply Tooling (C) to the joint face. Spread the sealant uniformly. Front housing (3) must be
installed within ten minutes of applying the sealant.
4. Install front housing (3) on the cylinder block.
5. Install belt tightener (2).
2/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 2 g01028154
6. Install front engine support (1).
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Install".
b. Install the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front
Seal - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:15:58 UTC+0800 2019
3/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02375078
Camshaft Idler Gear - Remove and Install
SMCS - 1206-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01027207
1. Rotate the crankshaft until the number one piston is at the top center position. Timing mark
(4) for camshaft idler gear (2) should be in line with timing mark (5) for crankshaft drive
gear (6).
2. Remove the bolts that fasten plate (1) to idler shaft (3). Remove plate (1).
3. Slide camshaft idler gear (2) from idler shaft (3).
4. Use Tooling (A) and a suitable press to remove the bearing from camshaft idler gear (2).
5. Remove the bolt and idler shaft (3) from the cylinder block.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Gp 1
NOTICE
2/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01027207
1. Position idler shaft (3) on the cylinder block. Install the bolt that holds idler shaft (3) to the
cylinder block. Tighten the bolt to a torque of 70 ± 15 N·m (51 ± 11 lb ft).
2. Use Tooling (A) and a suitable press to install the bearing in camshaft idler gear (2). Install
the bearing until the bearing is 0.40 ± 0.25 mm (0.016 ± 0.010 inch) below the front face of
camshaft idler gear (2).
3. Install camshaft idler gear (2) on idler shaft (3). Align timing mark (4) for camshaft idler
gear (2) with timing mark (5) for crankshaft drive gear (6).
4. Position plate (1) and install the bolts. Tighten the bolts to a torque of 70 ± 15 N·m
(51 ± 11 lb ft).
End By:
a. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:16:53 UTC+0800 2019
3/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i02370572
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01182877
1/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 1. Remove bolts (2) and valve mechanism cover (1).
2. Remove the seal from valve mechanism cover (1).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01182877
2/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 3 g01182875
1. Install the seal in valve mechanism cover (1).
2. Position valve mechanism cover (1) on the engine and install bolts (2). Tighten the bolts in a
numerical sequence.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Sep 10 20:17:49 UTC+0800 2019
3/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 322C EXCAVATOR EMR
Configuration: 322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED BY 3126 Engine
Disassembly and Assembly
3126B Engines for Caterpillar Built Machines
Media Number -SENR9581-06 Publication Date -01/08/2018 Date Updated -17/08/2018
i01982239
Valve Mechanism Cover Base - Remove and Install
SMCS - 1120-010
Removal Procedure
Start By:
a. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Disconnect the harness assembly from the valve mechanism cover base.
1/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. Illustration 1 g01027286
2. Disconnect harness assemblies (1) from each of the unit injectors.
3. Remove valve mechanism cover base (2).
Installation Procedure
Illustration 2 g01027286
2/3
322C L, 322C LN Hydraulic Excavators EMR00001-UP (MACHINE) POWERED B...
2019/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...