The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It outlines the required tools and multi-step procedures for removal and installation, which include using various tools to turn the cylinder head, remove the guides and seats, and install new guides and seats at the proper depths. Safety notices are provided to keep parts clean and contain fluids properly during the process.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...shudun96087
The document provides instructions for removing and installing valve guides, valve seat inserts, and an engine oil cooler on a Caterpillar C6.4 engine. It describes the required tools and steps to remove the components, clean and prepare the parts, and install new components. The procedures include removing valves, electronic injectors, and other engine parts before accessing the components and reinstalling parts after replacing guides, seats, and the oil cooler.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...qme229722
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involves using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
This document provides instructions for removing and installing various components of the C6.4 engine, including the inlet and exhaust valve guides, inlet and exhaust valve seat inserts, engine oil cooler, and related tools. The procedures describe removing components, cleaning parts, installing new parts, and reassembling components in reverse order of removal. Precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...kesi7153062
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler by disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler by removing mounting hardware and components. Assembly is the reverse of disassembly.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...fijsekkdmdm2w
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...zan2736ban
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...shudun96087
The document provides instructions for removing and installing valve guides, valve seat inserts, and an engine oil cooler on a Caterpillar C6.4 engine. It describes the required tools and steps to remove the components, clean and prepare the parts, and install new components. The procedures include removing valves, electronic injectors, and other engine parts before accessing the components and reinstalling parts after replacing guides, seats, and the oil cooler.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...qme229722
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involves using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
This document provides instructions for removing and installing various components of the C6.4 engine, including the inlet and exhaust valve guides, inlet and exhaust valve seat inserts, engine oil cooler, and related tools. The procedures describe removing components, cleaning parts, installing new parts, and reassembling components in reverse order of removal. Precautions are provided to keep parts clean and contain fluids during maintenance.
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler, which involves disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler, which includes removing mounting hardware and separating the core from the cover.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...kesi7153062
This document provides instructions for removing and installing valve guides, valve seat inserts, and disassembling and assembling the engine oil cooler on a Caterpillar C6.4 engine. The summary includes:
1) Procedures are provided for removing and installing valve guides and valve seat inserts, which involve using various specialty tools to remove and install the components.
2) Instructions are given for removing the engine oil cooler by disconnecting electrical connections and removing mounting bolts.
3) Steps are outlined for disassembling the engine oil cooler by removing mounting hardware and components. Assembly is the reverse of disassembly.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...fijsekkdmdm2w
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...zan2736ban
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...f8uesjdkdmdm
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and cleaning procedures are provided, as well as instructions for lubricating and installing replacement parts.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...f7fujksekmdm8u
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...8ufjsekddm8u
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and cleaning procedures are provided, as well as instructions for lubricating and installing replacement parts.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar cat 323 d s excavator (prefix rac) service repair manual (rac0000...idkdkddmd
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and cleaning procedures are provided, as well as instructions for lubricating and installing replacement parts.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...fujkskemdmdm4r
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes:
1. Removing the valves, electronic unit injectors, and turning the cylinder head to access the valve guides.
2. Using specialty tools to remove the old valve guides and install new guides.
3. Grinding notches in the valve seats, extracting the old seats, and installing new seats using specialty tools and lowering the temperature of the seats.
4. Reinstalling the valves and electronic unit injectors after installing new guides and seats.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...ufjksemd8ujd
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described, including removal, disassembly, and reassembly steps.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...km7seydwuhdw
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...fskekkdmdmdm3e
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described, including removal, disassembly, and reassembly steps.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...jdkskmdmdm
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and associated parts. Precautions are provided to keep parts clean and contain fluids.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described, including removal, disassembly, and reassembly steps.
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves cleaning the crankshaft, applying retaining compound, and pressing the new seal into place using a slide hammer puller. Care must be taken not to damage the crankshaft flange during installation.
This document provides instructions for removing and installing track carrier rollers, track rollers, and separating the track on a 320C Excavator. It describes:
1) Releasing tension on the track and loosening a relief valve before removing components.
2) Using tools like a hydraulic jack and lifting forks to support the track assembly and remove rollers and bolts.
3) Cleaning surfaces, positioning components, and reinstalling bolts and rollers in the reverse order of removal.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320C excavator. The oil pump removal instructions involve removing bolts, gears, seals and other components. The installation involves cleaning parts, pressing components, heating items, and torquing bolts. The water pump instructions describe draining coolant and removing four bolts to take off the pump. Reassembly involves installing seals, bearings and an impeller on a shaft.
This document provides instructions for assembling and disassembling parts of a 320 GC Excavator model BR4, including the travel motor and final drive. It lists the required tools and parts and includes illustrations of the assembly and disassembly procedures. The travel motor assembly instructions involve installing positioning rods and lifting eyes to hold parts in place while bolts are tightened. The final drive disassembly involves removing the final drive housing from the excavator and using link brackets and forcing screws to separate connected components.
Caterpillar Cat 305.5 Mini Hydraulic Excavator (Prefix DCK) Service Repair Ma...f8usejkdmmd8i
The document provides instructions for removing and installing track components on a 305.5 Mini Hydraulic Excavator, including:
- Removing and installing track rollers by raising the machine, removing bolts, and lowering it onto cribbing
- Separating the track by rotating it, removing shoes and bolts, and removing the master pin
- Reconnecting the track by installing the master pin and shoes with bolts
- Removing the front idler and track adjuster by sliding the track assembly away and lifting it off
- Installing the front idler and track adjuster by lifting it into place and sliding the track assembly over it
- Removing the recoil spring assembly
More Related Content
Similar to Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix HJC) Service Repair Manual Instant Download.pdf
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...f8uesjdkdmdm
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and cleaning procedures are provided, as well as instructions for lubricating and installing replacement parts.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...f7fujksekmdm8u
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...8ufjsekddm8u
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and cleaning procedures are provided, as well as instructions for lubricating and installing replacement parts.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar cat 323 d s excavator (prefix rac) service repair manual (rac0000...idkdkddmd
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and cleaning procedures are provided, as well as instructions for lubricating and installing replacement parts.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...fujkskemdmdm4r
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes:
1. Removing the valves, electronic unit injectors, and turning the cylinder head to access the valve guides.
2. Using specialty tools to remove the old valve guides and install new guides.
3. Grinding notches in the valve seats, extracting the old seats, and installing new seats using specialty tools and lowering the temperature of the seats.
4. Reinstalling the valves and electronic unit injectors after installing new guides and seats.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...ufjksemd8ujd
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described, including removal, disassembly, and reassembly steps.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...km7seydwuhdw
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
Caterpillar Cat 323D LN and 323D S Excavator (Prefix RAC) Service Repair Manu...fskekkdmdmdm3e
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described, including removal, disassembly, and reassembly steps.
Caterpillar Cat 323D S Excavator (Prefix RAC) Service Repair Manual (RAC00001...jdkskmdmdm
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and associated parts. Precautions are provided to keep parts clean and contain fluids.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. Key steps include:
1. Removing the valves, electronic unit injectors, and turning the cylinder head upside down on a repair stand.
2. Using specialty tools to remove the old valve guides and valve seat inserts from the cylinder head.
3. Cleaning the cylinder head and installing new valve guides and valve seat inserts using installer tools, ensuring the guides protrude the correct amount above the cylinder head surface.
The document provides instructions for removing and installing valve guides and valve seat inserts on a Caterpillar C6.4 engine. It describes the required tools and gives step-by-step procedures for removing and installing valve guides, removing and installing valve seat inserts, and precautions to take to prevent contamination. Dismantling and assembling the engine oil cooler is also described, including removal, disassembly, and reassembly steps.
Similar to Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix HJC) Service Repair Manual Instant Download.pdf (16)
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves cleaning the crankshaft, applying retaining compound, and pressing the new seal into place using a slide hammer puller. Care must be taken not to damage the crankshaft flange during installation.
This document provides instructions for removing and installing track carrier rollers, track rollers, and separating the track on a 320C Excavator. It describes:
1) Releasing tension on the track and loosening a relief valve before removing components.
2) Using tools like a hydraulic jack and lifting forks to support the track assembly and remove rollers and bolts.
3) Cleaning surfaces, positioning components, and reinstalling bolts and rollers in the reverse order of removal.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320C excavator. The oil pump removal instructions involve removing bolts, gears, seals and other components. The installation involves cleaning parts, pressing components, heating items, and torquing bolts. The water pump instructions describe draining coolant and removing four bolts to take off the pump. Reassembly involves installing seals, bearings and an impeller on a shaft.
This document provides instructions for assembling and disassembling parts of a 320 GC Excavator model BR4, including the travel motor and final drive. It lists the required tools and parts and includes illustrations of the assembly and disassembly procedures. The travel motor assembly instructions involve installing positioning rods and lifting eyes to hold parts in place while bolts are tightened. The final drive disassembly involves removing the final drive housing from the excavator and using link brackets and forcing screws to separate connected components.
Caterpillar Cat 305.5 Mini Hydraulic Excavator (Prefix DCK) Service Repair Ma...f8usejkdmmd8i
The document provides instructions for removing and installing track components on a 305.5 Mini Hydraulic Excavator, including:
- Removing and installing track rollers by raising the machine, removing bolts, and lowering it onto cribbing
- Separating the track by rotating it, removing shoes and bolts, and removing the master pin
- Reconnecting the track by installing the master pin and shoes with bolts
- Removing the front idler and track adjuster by sliding the track assembly away and lifting it off
- Installing the front idler and track adjuster by lifting it into place and sliding the track assembly over it
- Removing the recoil spring assembly
This document provides instructions for installing the fuel injection pump housing and governor on an excavator engine. It outlines 18 steps, including setting the number 1 piston to top center, installing timing pins, attaching the housing and governor, and connecting various lines and covers. Tools required include an engine turning tool, spanner wrench, and two fuel pump timing pins. Precise timing of the fuel injection pump camshaft is critical when attaching the housing.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix HC5) Service Repair ...f8usejkdmmd8i
The document provides instructions for removing and installing various components of a 304E2 CR Mini Hydraulic Excavator engine, including the fuel manifold rail, fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, and electronic unit injector. Safety precautions are outlined that must be followed when working on the fuel system, such as risks of high pressure fuel and containing any spilled fluids.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix ZGZ) Service Repair Manu...f8usejkdmmd8i
The document provides instructions for disassembling and assembling the final drive of a 319D L excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling the final drive, including pressing in bearings, installing seals, and determining the correct shim thickness. The overall procedure involves separating, cleaning, and reassembling over 15 individual parts and components of the final drive.
Caterpillar Cat 319D L Excavator (Prefix KRM) Service Repair Manual Instant D...f8usejkdmmd8i
This document provides instructions for disassembling and assembling the final drive of a 319D L excavator. It describes 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It also describes 31 steps for reassembling these components, including pressing in bearings, determining shim thickness, and installing seals using a special tool. Proper cleaning, lubrication, and use of replacement parts is emphasized throughout.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix CJ2) Service Repair ...f8usejkdmmd8i
The document provides instructions for servicing components of a 304E2CR Mini Hydraulic Excavator engine. It describes procedures for removing and installing the crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The steps include using the proper tools, cleaning parts, applying sealant, and tightening to the specified torque values.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix KC4) Service Repair ...f8usejkdmmd8i
The document provides instructions for removing and installing various engine components on a 304E2CR Mini Hydraulic Excavator including the crankshaft rear seal carrier, flywheel housing, crankshaft pulley, crankshaft front seal, idler gear, front housing, and valve mechanism cover. The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Precautions are provided regarding keeping parts clean and containing fluids.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix FC2) Service Repair ...f8usejkdmmd8i
The document provides instructions for removing and installing an engine oil cooler on a Caterpillar 304E2CR mini hydraulic excavator. The steps include draining coolant, removing hoses and clamps connecting the cooler, and removing mounting bolts. Reinstallation is the reverse of removal. Proper cleaning and torqueing of connections is emphasized.
Caterpillar Cat 304E Mini Hydraulic Excavator (Prefix TSR) Service Repair Man...f8usejkdmmd8i
This document provides instructions for removing and installing various track components on a 304E Mini Hydraulic Excavator, including the evaporator coil, track carrier roller, track roller, track, front idler, recoil spring, and hydraulic track adjuster. The procedures note required tools and safety precautions, and include illustrations and multiple step-by-step instructions for each component.
Caterpillar Cat 305.5 Mini Hydraulic Excavator (Prefix CXZ) Service Repair Ma...f8usejkdmmd8i
The document is a service repair manual that provides instructions for removing and installing components like the sprocket, final drive, and travel motor on a 305.5 Mini Hydraulic Excavator. It includes detailed removal and installation procedures with illustrations and lists required tools. Procedures include draining fluids, removing bolts and covers, disconnecting hoses, and lifting out heavy components. Disassembly steps describe removing gears, bearings, springs, and other internal parts.
Caterpillar Cat 304E Mini Hydraulic Excavator (Prefix TTN) Service Repair Man...f8usejkdmmd8i
The document provides instructions for servicing a 304E Mini Hydraulic Excavator. It describes procedures for removing and installing the sprocket and removing the final drive and travel motor. The final drive and travel motor are then disassembled by removing gears, bearings, seals, springs, and other internal components using the specified tools. Detailed illustrations accompany each step.
Caterpillar Cat 303.5E2CR Mini Hydraulic Excavator (Prefix CR6) Service Repai...f8usejkdmmd8i
This document provides instructions for installing and removing the governor and camshaft, and fuel injection pump on a 303.5E2CR Mini Hydraulic Excavator. It includes illustrations and step-by-step instructions for disassembling, cleaning, and reassembling these components. The instructions note to keep all parts clean and free of contaminants to prevent premature wear.
Caterpillar Cat 301.6C and 301.8C Mini Hydraulic Excavator (Prefix JSB) Servi...f8usejkdmmd8i
The document provides instructions for removing and disassembling various components of 301.6C and 301.8C mini hydraulic excavators, including the final drive and travel motor. The removal process involves draining fluids, disconnecting hoses, and removing bolts. Disassembly of the final drive and travel motor further requires removing retaining rings, springs, pins, seals and additional components using various specialized tools. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 140M 3 MOTOR GRADER (Prefix N9M) Service Repair Manual Instan...f8usejkdmmd8i
1) The document provides instructions for disassembling the bank valve on the front and rear frames of a Caterpillar 140M 3 motor grader.
2) It describes removing 17 parts from the front bank valve including covers, seals, control valves, plugs, springs, balls, and fittings. Special precautions are listed for releasing spring forces.
3) Disassembling the rear bank valve involves removing 14 parts like covers, seals, control valves, plugs, springs, and tie rods. Again, warnings are given for spring-loaded components.
Caterpillar Cat 140M 2 MOTOR GRADER (Prefix M9D) Service Repair Manual Instan...f8usejkdmmd8i
This document provides assembly instructions for a transmission in a 140M 2 motor grader. It lists required tools and parts and provides step-by-step instructions with accompanying illustrations. The transmission assembly involves installing bearings, gears, seals, pistons, clutches, and housing components in the specified order and with the correct torques. Proper cleaning, heating, lifting, and safety procedures are noted throughout the detailed assembly process.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625003
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 384-8861 Valve Guide Remover 1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/4(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. Illustration 2 g01377121
2. Use Tooling (A) in order to remove valve guides (2) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8862 Valve Guide Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/4(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Illustration 3 g01377130
1. Lubricate the outside of valve guides (2) (not shown) with clean engine oil.
2. Use Tooling (E) in order to install new valve guides (2) . Install valve guide (2) so that
valve guide (2) protrudes 16.000 mm (0.6299 inch) above Surface (X) of cylinder head (1) .
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
b. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:15:14 UTC+0800 2020
4/4(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625001
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
166-7441 Valve Seat Extractor Tool 1
6V-4194 Valve Seat Extractor (1)
1
6V-4196 Valve Seat Extractor (1)
1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
( 1 )
Component of the Valve Seat Extractor Tool Group.
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Remove".
NOTICE
Keep all parts clean from contaminants.
1/5(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Contaminants may cause rapid wear and shortened component life.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B ) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B ) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/5(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Illustration 2 g01376571
2. Use the valve seat grinder of Tooling (A) in order to notch the valve seat.
Illustration 3 g01376578
3. Use the valve seat extractor of Tooling (A) to remove the inlet and exhaust valve seats.
4. Clean the valve seat in the cylinder head. Remove any rough areas from the valve seat in the
cylinder head.
5. Repeat Steps 2 through 4 for the remaining inlet valve seat inserts and exhaust valve seat
inserts.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8859 Valve Seat Installer 1
F 384-8860 Valve Seat Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. Illustration 4 g01377071
Typical Example
1. Lower the temperature of the new inlet valve seat inserts (2) . Use Tooling (E) in order to
install a new inlet valve seat insert (2) (not shown) in the cylinder head.
Illustration 5 g01376588
Typical Example
2. Lower the temperature of new exhaust valve seat inserts (3) . Use Tooling (E) and Tooling
(F) in order to install the new exhaust valve seat insert (3) (not shown) in the cylinder head.
Note: The temperature of exhaust valve seat insert (3) is lowered in order to ease the
installation of exhaust valve seat insert (3) .
3. Repeat Step 1 and 2 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
b. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Install".
4/5(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746253
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
a. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Illustration 1 g01375410
1. Disconnect harness assembly (1).
2. Remove bolts (2) and remove engine oil cooler (3). Remove gasket (4) (not shown) from the
engine cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:17:05 UTC+0800 2020
2/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746254
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
a. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the
components should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly
procedures on a clean work surface. Keep components covered and protected at all times.
1/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Illustration 1 g01375411
1. Remove bolts (9) and the washers. Remove cover (8) and gasket (7).
2. Remove nuts (5) and the washers from engine oil cooler cover (4). Remove nuts (6) and the washers
from engine oil cooler cover (4).
3. Remove engine oil cooler core (2) from engine oil cooler cover (4). Remove gaskets (1) and (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:18:01 UTC+0800 2020
2/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746255
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the gaskets for damage. Replace the components, if necessary.
1/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Illustration 1 g01375411
1. Install gaskets (3) and (1) to engine oil cooler core (2). Position engine oil cooler core (2) to engine
oil cooler cover (4).
2. Install the washers and nuts (6). Install the washers and nuts (5).
3. Install gasket (7) and position cover (8). Install the washers and bolts (9).
End By:
a. Install the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:18:56 UTC+0800 2020
2/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746256
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Illustration 1 g01375410
1. Install gasket (4) (not shown). Position engine oil cooler (3) to the engine block. Install bolts
(2).
1/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. 2. Connect harness assembly (1).
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:19:52 UTC+0800 2020
2/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751808
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
Start By:
a. Remove the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377673
1/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. 1. Remove engine oil relief valve (1).
2. Remove gasket (2) (not shown). Discard gasket (2).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01377673
1. Install a new gasket (2) (not shown).
2. Install engine oil relief valve (1). Tighten engine oil relief valve (1) to a torque of
49 ± 5 N·m (36 ± 4 lb ft).
End By:
a. Install the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:20:48 UTC+0800 2020
2/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751881
Engine Oil Bypass Valve - Remove and Install
SMCS - 1306-010-BV
Removal Procedure
Start By:
a. Remove the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377713
1. Remove engine oil bypass valve (1). Remove gasket (2) (not shown). Discard gasket (2).
1/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01377713
1. Install a new gasket (2) (not shown). Install engine oil bypass valve (1). Tighten engine oil
bypass valve (1) to a torque of 69 ± 5 N·m (51 ± 4 lb ft).
End By:
a. Install the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:21:44 UTC+0800 2020
2/2(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751822
Engine Oil Pump Relief Valve - Remove and Install
SMCS - 1304-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377698
1/3(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. Illustration 2 g01377701
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
1. Remove engine oil pump relief valve (1).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
2/3(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
24. Illustration 3 g01377701
Illustration 4 g01377698
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install engine oil pump relief valve (1). Tighten engine oil pump relief valve (1) to a torque
of 59 ± 10 N·m (44 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Oct 27 09:22:39 UTC+0800 2020
3/3(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR HJC
Configuration: 320D RR & 320D LRR Excavators HJC00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02741773
Engine Oil Pump - Remove
SMCS - 1304-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2320 Combination Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00607826
Note: Illustration 1 does not show that the front housing is removed from the cylinder
block.
1. Remove bolts (1) from the cover (2).
2. Remove cover (2) for the engine oil pump from the front housing. Remove gasket (3) (not
shown).
Illustration 2 g00607770
3. Remove driven gear (4) for the oil pump. Pull the gear straight out of the front housing (5)
(slip fit).
2/4(W)
w
2020/10/27
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...