The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using various tools to remove components like the muffler, flywheel housing, and crankshaft rear seal prior to removing the flywheel. The removal procedure involves using a link bracket and forcing bolts to remove the flywheel from the housing. The installation procedure specifies cleaning and applying compounds before pressing the ring gear and wear sleeve onto the flywheel and crankshaft. Torque specifications and checks are also provided.
The document provides instructions for removing and installing a flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Instructions are given for removing the flywheel itself using a lifting device and forcing bolts. Reinstalling involves cleaning surfaces, applying retaining compound, and torquing bolts to the specified value. The process for removing and installing the crankshaft rear seal and flywheel housing are also summarized.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new wear sleeve and rear oil seal. Overall, the document contains detailed removal and installation steps for servicing the flywheel assembly.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new wear sleeve and rear oil seal. Overall, the document contains detailed removal and installation steps for servicing the flywheel assembly.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...dkdmidkkdk
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also describes installing a new oil seal during reinstallation using special tools and reinstalling the flywheel.
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also describes installing a new oil seal during reinstallation using special tools and reinstalling the flywheel.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new crankshaft rear seal and wear sleeve. Reinstallation involves cleaning surfaces, applying retaining compound, and reinstalling bolts and brackets.
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also details installing the housing, ensuring all parts are clean, and reinstalling the flywheel and electric starting motor.
The document provides instructions for removing and installing a flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, and rear crankshaft seal. Instructions are given for cleaning and preparing the components, installing a new rear seal and wear sleeve, and securing the flywheel housing and flywheel. Similar procedures are outlined for removing and installing the crankshaft pulley.
The document provides instructions for removing and installing a flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Instructions are given for removing the flywheel itself using a lifting device and forcing bolts. Reinstalling involves cleaning surfaces, applying retaining compound, and torquing bolts to the specified value. The process for removing and installing the crankshaft rear seal and flywheel housing are also summarized.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new wear sleeve and rear oil seal. Overall, the document contains detailed removal and installation steps for servicing the flywheel assembly.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new wear sleeve and rear oil seal. Overall, the document contains detailed removal and installation steps for servicing the flywheel assembly.
Caterpillar cat 320 d lrr excavator (prefix ejt) service repair manual (ejt00...dkdmidkkdk
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also describes installing a new oil seal during reinstallation using special tools and reinstalling the flywheel.
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also describes installing a new oil seal during reinstallation using special tools and reinstalling the flywheel.
The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the muffler brackets and flywheel bolts. Lifting devices are needed due to the flywheel's 50 kg weight. Instructions are given for removing the ring gear from the flywheel as well as installing a new crankshaft rear seal and wear sleeve. Reinstallation involves cleaning surfaces, applying retaining compound, and reinstalling bolts and brackets.
The document provides instructions for removing and installing a flywheel housing on a 320D LRR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It notes the housing weighs approximately 29 kg. It also details installing the housing, ensuring all parts are clean, and reinstalling the flywheel and electric starting motor.
The document provides instructions for removing and installing a flywheel on a 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, and rear crankshaft seal. Instructions are given for cleaning and preparing the components, installing a new rear seal and wear sleeve, and securing the flywheel housing and flywheel. Similar procedures are outlined for removing and installing the crankshaft pulley.
John Deere XUV 850D Gator Utility Vehicle Service Repair Manual (tm1737).pdffjskekmdmdm1
This technical manual provides service and repair information for the John Deere XUV 850D Gator utility vehicle. The manual is organized into sections covering specifications, safety, components, operation, diagnostics, and repairs. It is intended as a resource for experienced technicians to service and repair this vehicle. Safety notices and procedures are highlighted throughout to warn technicians of hazards.
This document provides instructions for removing and installing various engine components on a Caterpillar C9.3 engine, including:
1) Removing and installing the valve mechanism cover, involving disconnecting hoses and harnesses, removing nuts and bolts, and installing in reverse order.
2) Removing and installing the compression brake, which requires adjusting engine valve lash, removing/installing bolts, checking seals, and setting brake lash.
3) Disassembling and assembling the compression brake valve assembly by removing/installing bolts and O-rings.
4) Removing and installing the rocker arm shaft assembly, which involves disconnecting harnesses, removing nuts and bol
This document provides instructions for installing a flywheel on a Caterpillar 434F backhoe loader engine. It describes cleaning and preparing the flywheel and crankshaft, installing guide bolts and lifting the flywheel into place with bolts finger tight before fully tightening. It also describes inspecting the flywheel runout after installation and reinstalling other components like the electric starting motor.
1) The document provides instructions for removing and installing a lifter group on a C2.2 engine. It lists the required tool and removal steps, which include using a telescopic magnet to remove the lifters from the valve mechanism housing.
2) Installation instructions include cleaning components, lubricating the lifters, and inserting the lifters into the valve mechanism housing using the telescopic magnet. Proper lifter orientation is noted.
3) Completing the job involves installing the valve mechanism cover after checking lifter rotation.
This document provides instructions for removing and installing various engine components on a 246 Skid Steer Loader, including:
- Removing and installing the turbocharger
- Removing and installing the exhaust manifold
- Removing the inlet manifold
- Installing the inlet manifold
- Removing and installing inlet and exhaust valve springs
The document includes illustrations and multistep procedures for each component, with notices about keeping parts clean and containing fluids.
This document provides instructions for disassembling and assembling the governor components in a Caterpillar 3034 engine. It describes removing components like the governor weight assembly, speed control lever, and linkage for the fuel injection pump. Detailed steps are provided to disassemble each component and check for wear. The assembly section then describes reinstalling each part and adjusting any settings that may be affected. Precautions are noted to keep parts clean and contain fluids during the process.
The document provides instructions for removing and installing an exhaust manifold on a 249D Compact Track Loader powered by a C2.2 engine. The removal procedure involves loosening fasteners, removing the exhaust manifold and gasket, and removing any studs. For installation, clean surfaces are required, a new gasket is installed, the manifold is aligned and fastened, and bolts are tightened to the specified torque. Safety precautions and notes about different engine models are provided.
CASE IH AXIAL-FLOW 7230 Combine Service Repair Manual (PIN YDG222001 and abov...fjskekmdmdm1
This document is a service manual for Axial-Flow combine models 7230, 8230, and 9230 from CNH America LLC. It contains over 20 sections that provide technical specifications, diagrams, and repair instructions for the engine, transmission, axles, hydraulics, electrical systems, attachments/headers, and other major components of the combines. The service manual is intended to assist technicians in servicing and repairing the combines.
CASE IH AXIAL-FLOW 7230 Tier 4 Combine Service Repair Manual.pdffjskekmdmdm1
This document is the service manual for Case IH Axial-Flow combines. It contains sections on the engine, transmission, axles, hydraulics, electrical systems, attachments, and other components. The manual provides technical specifications and instructions for servicing and repairing parts. It aims to help qualified service technicians safely maintain and fix issues with the combines.
CASE IH AXIAL-FLOW 7150 Tier 4B (final) Combine Service Repair Manual (PIN YJ...fjskekmdmdm1
This document is a service manual that provides technical specifications and repair instructions for Case IH Axial-Flow combines, including the 5150, 6150, and 7150 models that meet Tier 4B emissions standards. It contains detailed sections on the engine, transmission, axles, hydraulic and electrical systems, cab climate control, and other components. Repair procedures are organized by system and subsection with part numbers listed. The manual is intended to guide maintenance and repairs of these combines.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...fjskekmdmdm1
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover by loosening the clamp.
3. Removing the bolts securing the regulator housing and removing the housing to access the internal components.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 320D L excavator. The removal procedure involves using a link bracket and lifting device to remove the flywheel housing after removing bolts and washers. A driver group is then used to remove the oil seal from the housing. The installation procedure is not described.
John Deere 47 and 59 Snowbowers Service Repair Manual.pdffjskekmdmdm1
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
The document provides instructions for removing and installing a flywheel housing on a 422E Backhoe Loader. Key steps include:
1. Removing the flywheel, bolts, and lifting the housing off the engine block using lifting devices.
2. Inspecting the crankshaft rear seal for leaks before installing a cleaned housing with dowels and bolts, checking alignment with a dial indicator.
3. Reinstalling the flywheel to complete the process.
Caterpillar Cat 307 EXCAVATOR (Prefix 2WM) Service Repair Manual (2WM00001-00...fjskekmdmdm1
This document provides instructions for removing, disassembling, assembling, and installing pistons and connecting rods in a 3054 engine. The removal process involves removing the cylinder head, oil pump, and piston cooling jets before pushing the pistons and connecting rods out of the cylinder block. Disassembly requires using tools to remove the piston rings and pins. Assembly requires lubricating and pressing components, and ensuring proper ring and bearing installation. Installation involves cleaning, lubricating, and inserting the assembled pistons and connecting rods into the cylinder liner and connecting to the crankshaft.
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure involves using a slide hammer puller to remove the existing seal after drilling holes in it. For installation, a front seal installer tool is used to carefully push the new seal onto the crankshaft flange. Proper cleaning and containment of fluids is emphasized.
Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Man...fjskekmdmdm1
The document provides instructions for removing and installing various engine components on a 307D Mini Hydraulic Excavator including the fuel filter and water separator base, engine oil filter and oil filter base, and air cleaner. The procedures describe draining fluids, disconnecting hoses, removing bolts and filters, cleaning parts, applying oil, and reinstalling components in the reverse order of removal. Safety precautions are provided to prevent injury and contain fluids.
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover and removing mounting bolts.
3. Installing the new regulator by reversing the removal steps, filling the cooling system, and tightening all connections to the specified torques.
Cleanliness is important to prevent contamination, and safety precautions are described for working with hot coolant and steam.
The document provides instructions for removing and installing various crankshaft and flywheel components on a Caterpillar 272D skid steer loader. The procedures include removing the flywheel, flywheel housing, crankshaft rear seal, crankshaft rear seal carrier, and crankshaft pulley. Illustrations and torque specifications are provided. Tools required are also listed. The document is from a Caterpillar service manual and aims to guide maintenance and repair of engine components.
John Deere XUV 850D Gator Utility Vehicle Service Repair Manual (tm1737).pdffjskekmdmdm1
This technical manual provides service and repair information for the John Deere XUV 850D Gator utility vehicle. The manual is organized into sections covering specifications, safety, components, operation, diagnostics, and repairs. It is intended as a resource for experienced technicians to service and repair this vehicle. Safety notices and procedures are highlighted throughout to warn technicians of hazards.
This document provides instructions for removing and installing various engine components on a Caterpillar C9.3 engine, including:
1) Removing and installing the valve mechanism cover, involving disconnecting hoses and harnesses, removing nuts and bolts, and installing in reverse order.
2) Removing and installing the compression brake, which requires adjusting engine valve lash, removing/installing bolts, checking seals, and setting brake lash.
3) Disassembling and assembling the compression brake valve assembly by removing/installing bolts and O-rings.
4) Removing and installing the rocker arm shaft assembly, which involves disconnecting harnesses, removing nuts and bol
This document provides instructions for installing a flywheel on a Caterpillar 434F backhoe loader engine. It describes cleaning and preparing the flywheel and crankshaft, installing guide bolts and lifting the flywheel into place with bolts finger tight before fully tightening. It also describes inspecting the flywheel runout after installation and reinstalling other components like the electric starting motor.
1) The document provides instructions for removing and installing a lifter group on a C2.2 engine. It lists the required tool and removal steps, which include using a telescopic magnet to remove the lifters from the valve mechanism housing.
2) Installation instructions include cleaning components, lubricating the lifters, and inserting the lifters into the valve mechanism housing using the telescopic magnet. Proper lifter orientation is noted.
3) Completing the job involves installing the valve mechanism cover after checking lifter rotation.
This document provides instructions for removing and installing various engine components on a 246 Skid Steer Loader, including:
- Removing and installing the turbocharger
- Removing and installing the exhaust manifold
- Removing the inlet manifold
- Installing the inlet manifold
- Removing and installing inlet and exhaust valve springs
The document includes illustrations and multistep procedures for each component, with notices about keeping parts clean and containing fluids.
This document provides instructions for disassembling and assembling the governor components in a Caterpillar 3034 engine. It describes removing components like the governor weight assembly, speed control lever, and linkage for the fuel injection pump. Detailed steps are provided to disassemble each component and check for wear. The assembly section then describes reinstalling each part and adjusting any settings that may be affected. Precautions are noted to keep parts clean and contain fluids during the process.
The document provides instructions for removing and installing an exhaust manifold on a 249D Compact Track Loader powered by a C2.2 engine. The removal procedure involves loosening fasteners, removing the exhaust manifold and gasket, and removing any studs. For installation, clean surfaces are required, a new gasket is installed, the manifold is aligned and fastened, and bolts are tightened to the specified torque. Safety precautions and notes about different engine models are provided.
CASE IH AXIAL-FLOW 7230 Combine Service Repair Manual (PIN YDG222001 and abov...fjskekmdmdm1
This document is a service manual for Axial-Flow combine models 7230, 8230, and 9230 from CNH America LLC. It contains over 20 sections that provide technical specifications, diagrams, and repair instructions for the engine, transmission, axles, hydraulics, electrical systems, attachments/headers, and other major components of the combines. The service manual is intended to assist technicians in servicing and repairing the combines.
CASE IH AXIAL-FLOW 7230 Tier 4 Combine Service Repair Manual.pdffjskekmdmdm1
This document is the service manual for Case IH Axial-Flow combines. It contains sections on the engine, transmission, axles, hydraulics, electrical systems, attachments, and other components. The manual provides technical specifications and instructions for servicing and repairing parts. It aims to help qualified service technicians safely maintain and fix issues with the combines.
CASE IH AXIAL-FLOW 7150 Tier 4B (final) Combine Service Repair Manual (PIN YJ...fjskekmdmdm1
This document is a service manual that provides technical specifications and repair instructions for Case IH Axial-Flow combines, including the 5150, 6150, and 7150 models that meet Tier 4B emissions standards. It contains detailed sections on the engine, transmission, axles, hydraulic and electrical systems, cab climate control, and other components. Repair procedures are organized by system and subsection with part numbers listed. The manual is intended to guide maintenance and repairs of these combines.
Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001...fjskekmdmdm1
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover by loosening the clamp.
3. Removing the bolts securing the regulator housing and removing the housing to access the internal components.
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 320D L excavator. The removal procedure involves using a link bracket and lifting device to remove the flywheel housing after removing bolts and washers. A driver group is then used to remove the oil seal from the housing. The installation procedure is not described.
John Deere 47 and 59 Snowbowers Service Repair Manual.pdffjskekmdmdm1
This technical manual provides information and specifications for John Deere commercial and consumer equipment, including several mower, tiller, broom, and snowblower models. The manual is organized systematically to keep all information for a particular system together. Safety is the first section and introduces safety symbols and guidelines to follow when operating the equipment.
The document provides instructions for removing and installing a flywheel housing on a 422E Backhoe Loader. Key steps include:
1. Removing the flywheel, bolts, and lifting the housing off the engine block using lifting devices.
2. Inspecting the crankshaft rear seal for leaks before installing a cleaned housing with dowels and bolts, checking alignment with a dial indicator.
3. Reinstalling the flywheel to complete the process.
Caterpillar Cat 307 EXCAVATOR (Prefix 2WM) Service Repair Manual (2WM00001-00...fjskekmdmdm1
This document provides instructions for removing, disassembling, assembling, and installing pistons and connecting rods in a 3054 engine. The removal process involves removing the cylinder head, oil pump, and piston cooling jets before pushing the pistons and connecting rods out of the cylinder block. Disassembly requires using tools to remove the piston rings and pins. Assembly requires lubricating and pressing components, and ensuring proper ring and bearing installation. Installation involves cleaning, lubricating, and inserting the assembled pistons and connecting rods into the cylinder liner and connecting to the crankshaft.
This document provides instructions for removing and installing the crankshaft front seal of a Caterpillar C6.4 engine.
The removal procedure involves using a slide hammer puller to remove the existing seal after drilling holes in it. For installation, a front seal installer tool is used to carefully push the new seal onto the crankshaft flange. Proper cleaning and containment of fluids is emphasized.
Caterpillar Cat 307D Mini Hydraulic Excavator (Prefix DSG) Service Repair Man...fjskekmdmdm1
The document provides instructions for removing and installing various engine components on a 307D Mini Hydraulic Excavator including the fuel filter and water separator base, engine oil filter and oil filter base, and air cleaner. The procedures describe draining fluids, disconnecting hoses, removing bolts and filters, cleaning parts, applying oil, and reinstalling components in the reverse order of removal. Safety precautions are provided to prevent injury and contain fluids.
This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover and removing mounting bolts.
3. Installing the new regulator by reversing the removal steps, filling the cooling system, and tightening all connections to the specified torques.
Cleanliness is important to prevent contamination, and safety precautions are described for working with hot coolant and steam.
The document provides instructions for removing and installing various crankshaft and flywheel components on a Caterpillar 272D skid steer loader. The procedures include removing the flywheel, flywheel housing, crankshaft rear seal, crankshaft rear seal carrier, and crankshaft pulley. Illustrations and torque specifications are provided. Tools required are also listed. The document is from a Caterpillar service manual and aims to guide maintenance and repair of engine components.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR PHX
Configuration: 320D & 320D L Excavators PHX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02743771
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B Forcing bolts M16 - 2 by 120 mm 2
Start By:
a. Remove the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
b. Remove the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. Illustration 1 g01374966
1. Remove muffler brackets (1).
Illustration 2 g01374968
Illustration 3 g01374970
2. Remove bolts (2).
3. Install Tooling (A) and a suitable lifting device onto flywheel (3).
4. Use Tooling (B) in order to remove flywheel (3) out of the housing. The weight of flywheel
(3) is approximately 50 kg (110 lb).
2/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. 5. Perform the following procedure in order to remove the flywheel ring gear.
Illustration 4 g01374977
Typical Example
a. Place flywheel (3) and ring gear (4) on suitable cribbing.
Note: Mark the orientation of ring gear (4) on flywheel (3) for assembly purposes.
Always wear protective gloves when handling parts that have been
heated.
b. Raise the temperature of ring gear (4) uniformly.
c. Remove the ring gear (4) by tapping ring gear (4) all the way around flywheel (3).
d. Reposition flywheel (3) in order to remove ring gear (4).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 2 23:18:23 UTC+0800 2020
3/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR PHX
Configuration: 320D & 320D L Excavators PHX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02744399
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Raise the temperature of the ring gear 149 °C (300 °F).
1/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. b. Use a suitable press in order to install the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g01374993
2. Install Tooling (A) and a suitable lifting device onto flywheel (3).
3. Install flywheel (3). The weight of flywheel (3) is approximately 50 kg (110 lb).
Illustration 2 g01374968
4. Install bolts (2) in order to secure flywheel (3) onto the crankshaft. Tighten bolts (2) to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tooling (A) from flywheel (3).
2/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. Illustration 3 g01374966
6. Install muffler brackets (1).
7. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
End By:
a. Install the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
b. Install the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 2 23:19:19 UTC+0800 2020
3/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR PHX
Configuration: 320D & 320D L Excavators PHX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
9. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR PHX
Configuration: 320D & 320D L Excavators PHX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 2 23:21:11 UTC+0800 2020
3/3(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR PHX
Configuration: 320D & 320D L Excavators PHX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742697
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
b. Remove the flywheel and ring gear. Refer to Disassembly and Assembly, "Flywheel -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. Illustration 1 g01374571
1. Install Tooling (A), and a suitable lifting device onto flywheel housing (3).
2. Remove bolts (2) and the washers that secure flywheel housing (3) to the cylinder block.
3. Remove flywheel housing (3). The weight of flywheel (3) is approximately 29 kg (65 lb).
4. Remove gasket (1) (not shown).
Illustration 2 g01374572
5. Use Tooling (B) in order to remove the oil seal (4) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
NOTICE
2/4(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
15. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01374614
1. Use Tooling (B) in order to install the oil seal (4) (not shown).
Illustration 4 g01374571
2. Check the condition of two dowels (not shown). If dowels are damaged, use new parts for
replacement.
3. Clean old gasket (1) (not shown) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
4. Place flywheel housing (3) in position on the cylinder block.
5. Install the washers and bolts (2) in order to secure flywheel housing (3) to the cylinder
block.
6. Remove Tooling (A).
End By:
3/4(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Feb 2 23:22:06 UTC+0800 2020
4/4(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D L EXCAVATOR PHX
Configuration: 320D & 320D L Excavators PHX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i06790404
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket(1)
1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Remove the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
1/4(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
19. Illustration 1 g00604778
2. Use Tooling (B) in order to remove nut (1) and washer (2) from the threaded end of the
crankshaft.
Illustration 2 g00604784
3. Use Tooling (A) in order to remove crankshaft pulley (3) from the engine.
2/4(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Illustration 3 g00604792
4. If it is necessary to remove wear sleeve (4) from crankshaft pulley (3), use a suitable
hammer and a suitable chisel. Hold the suitable chisel at right angles to the surface of the
wear sleeve. Tap the wear sleeve in three places. You can remove the wear sleeve once the
tension is released.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 6V-9120 Socket(1)
1
C 1P-0510 Driver Gp 1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Raise the temperature of the wear sleeve. Use Tooling (C) in order to install the wear sleeve
onto the crankshaft pulley.
3/4(W)
w
2020/2/2
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...